User Manual v1.0

User Manual v1.0
User Manual v1.0
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
•
•
•
•
•
•
•
GSM communicator ET07 (further referenced as system) contains a radio transceiver operating in GSM900 and GSM1800 bands.
Don’t use the system where it can interfere with other devices and cause any potential danger.
Don’t use the system with medical devices if this is required in the manual of the medical device.
Don’t use the system in hazardous environment.
Don’t expose the system to high humidity, chemical environment or mechanical impacts.
Don’t attempt to personally repair the system.
System labelling sticker is at the bottom of the device.
System ET07 is a device mounted in limited access areas. Any system repairs must be done only by qualified, safety aware
personnel.
Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance
must not be done during stormy conditions.
The system must be powered by main 11-24V 50Hz ~300mA AC or 11-24V --- 300mA DC power supply which must be approved by LST EN 60950-1 standard and be easily accessible.
Any additional devices linked to the system ET07 (computer, alarm control panel etc.) must be approved by LST EN 60950-1
standard.
External power supply can be connected to AC mains only inside
installation room with automatic 2-pole circuit breaker capable of
disconnecting circuit in the event of short circuit or over-current condition. Open circuit breaker must have a gap between connections of
more than 3mm.
Phase
Null
Grounding
AC 230V
50 Hz/DC 24V
ET07
USB cable
Fuse F1 type 5x20 mm 3A Slow blown. Blown fuse cannot be replaced by the user and the replacement fuses have to be
exactly the same as indicated by the manufacturer.
The device is fully turned off by disconnecting 2-pole switch off device of the external power supply or any other linked
device that the system ET07 is powered from.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that in the EU
the product must not be disposed of together with household waste.
Copyright © “ELDES UAB”, 2009. All rights reserved.
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from “ELDES
UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this
COMMUNICATOR ET07 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt/ce.
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers
but does not guarantee against such events. “ELDES UAB” will not take any responsibility regarding
personal, property or revenue loss while using the
system. “ELDES UAB” responsibility according to
local laws does not exceed value of the purchased
system. “ELDES UAB” is not affiliated with GSM operators providing cellular services, therefore is not
responsible for network services, coverage or its
operation.
Manufacturer Warranty
The system carries a 24-month warranty by the
manufacturer “ELDES UAB”.
Warranty period starts from the day the system
has been purchased by the end user. The warranty
is valid only if the system has been used as intended, following all guidelines listed in the manual
and within specified operating conditions. Receipt
with purchase date must be kept as a proof.
Content
1 General Information
1.1 Function........................................................................................................ 12
1.2 Operation Description..............................................................................12
1.3 Technical Specifications...........................................................................12
1.4 Connection Circuit.................................................................................... 13
1.5 Connectors and LED Indicators Functionality................................. 13
1.6 System Installation.................................................................................... 14
1.7 Light Emitting Indicators Functionality............................................. 15
2. System Pre-operation
2.1 Informing Security Service Mode........................................................ 16
2.2 Informing Users via SMS Messages Mode........................................ 16
2.3 Informing Security Service and Users Mode.................................... 16
3. Appendix
3.1 Restoring Factory Default Parameters.................................................17
3.2 ET07 Configuration Program................................................................. 17
3.3 Technical Support...................................................................................... 17
The warranty is voided if the system has been
exposed to mechanical impacts, chemicals, high
humidity, fluids, corrosive and hazardous environment or other force majeure factors.
Package Content
1. System ET07.............................................................1 pcs
2. ET07 user manual..................................................1 pcs
3. GSM antenna...........................................................1 pcs
About User Manual. Quick Start.
This document describes remote informing system ET07, its operation and installation. It is very important to read User Manual before
start using the system. A quick start guide is located in first two chapters.
1. General Information
1.1 Function
Communicator ET07 is for transferring information from the Alarm Control Panel to the monitoring station via GSM audio connection channel or/and users via SMS message.
The system van be used in the following applications:
•
Property security
•
To make and receive telephone calls via GSM audio connection channel
1.2 Operation Description
Communicator ET07 works over GSM network. The communicator transmits CONTACT ID and 4+2 protocol messages and fully
imitates telephone line. When dialling a number with a telephone or via Alarm Control Panel, tonal (DTMF) number dialling mode
must be enabled. The user can also call from communicator to the telephone.
Communicator ET07 can operate in 3 modes, i. e.:
1. transmits information from the Alarm Control Panel to the monitoring station via GSM audio connection signal;
2. transmits information from the Alarm Control Panel only to the registered users via SMS message;
3. transmits information from the Alarm Control Panel to the monitoring station via GSM audio connection signal as well as
to registered users via SMS message.
An additional computer program ET07 Configuration Tool is also used for configurations which are necessary for the system to
operate in the second and third modes, i. e., to send SMS messages to the registered users. The device is connected to the computer via USB or RS232 type connection (depending on which type of connection is implemented in the card – see fig. 1).
1.3 Technical Specifications
Electrical and Mechanical Specifications
Supply voltage
Current used in standby mode
GSM modem frequency
Supported protocols
Maximum number of users to whom SMS messages are delivered
Dimensions
Operating temperature range
Generated phone line voltage
Generated phone line current
Generated phone line impedance
Ringing voltage of generated phone line
Dial tone of generated phone line
12
11-24V 50 Hz ~ 300mA max ar 11-24V
70mA max
900/1800/1900 MHz
CONTACT ID, 4+2
5
139x84 mm
-20...+55oC
48 V
25 mA
600 Ohm
± 72 V (25 Hz)
350 Hz
300mA max
1.4 Connection Circuit
For configurations
GSM antenna
SET
MODE
PROG
GSM MODEM
DEFAULT
ANT
RS232
USB
SIM CARD
Connection
for telephone
RJ11
FUSE
3A
AC/DC
1.1/3.5mm
INFO
STATUS
GSM TEL LINE
AC/DC
Power
Supply DC
RING/TIP
ALARM
CONTROL PANEL
AUX
1.5 Connectors and LED Indicators Functionality
Main Units
Light Emitting Diodes LED
GSM MODEM
GSM network 900/1800/1900 MHz modem
INFO
Working mode indicator
SIM CARD
SIM card
STATUS
Device activity indicator
ANT
GSM antenna SMA type connector
GSM
GSM network quality indicator
FUSE
3A fuse
Connector Functionality
Labelling
Explanation
AC/DC
Power supply connection pins
AC/DC 1,1/3,5mm
Alternative power supply connection pins. Connected in parallel with AC/DC connection. Internal diameter of
the plug is 1.1 mm, , external diameter of the plug is 3.5 mm
TEL LINE
Pins connected to the Alarm Control Panel pins RING and TIP. Connected in parallel with RJ11 connection.
RJ11
RJ11 type connection for telephone. Connected in parallel with TEL LINE connection.
DEFAULT
Connectors for restoring factory default settings
RS232
COM port connection
USB
Mini USB port
SET
Connectors for enabling the 3rd operation mode of the device
MODE
Connectors for connecting the 2nd operation mode of the device
PROG
Not used
User manual ELDES ET07 v1.0
13
1.6 System Installation
Note
Due to GSM network characteristics it is recommended to use the system ET07 with the same GSM operator which is used by
system users. Thus you will ensure the quickest SMS message delivery and receipt.
Note
To ensure maximum system operation reliability we recommend do not use prepaid cards. If the balance is insufficient the
system will not be able to inform users about the alarm.
IMPORTANT
Power supply at Alarm Control Panel must be disconnected before any installation or tuning work.
Device installation and Pre-operation:
1.
Fasten the system in the box using fastening holders
2.
Place SIM card in the holder but make sure that SIM card PIN code is disabled. (PIN code can be disabled by putting SIM card
into mobile phone and following proper menus). SIM card should not have any remaining SMS messages.
3.
Connect the antenna (the device cannot be turned on without antenna).
4.
Connect the circuit as shown in fig. no. 2 – connect telephone line output of the Alarm Control Panel (RING/TIP) to TEL LINE
connectors of communicator ET07. In this case power supply is usually used as AUX output of Alarm Control Panel.
5.
When AC power supply (ground transformer) is used, connect according to circuit no. 3. In this case you do not need to
connect any other power supplies.
6.
The system should start in less than a minute. STATUS indicator should be blinking every five seconds indicating connection
to GSM network. If the indicator is blinking very frequently, i. e., several times per second, it is possible that SIM card is inserted incorrectly or PIN code request is not disabled.
TEL LINE
ET07
AC/DC
AC/DC
Fuse 500 mA
RING/TIP
Fig. No. 2
Alarm Control Panel
~10-24V
~230V 50Hz
AUX
Fig. No. 3
The system can be installed only in a metal or non-flammable plastic box. When the metal box is also used as power supply
ground transformer it is necessary to ground the box using yellow/green colour cable. For the connection of ground 230V transformer use 3x0.75 mm2 1 thread double isolated cable. The initial winding of the ground transformer must be connected through
0.5A fuse. 230V power supply cables cannot be grouped with low voltage cable group. For the connection of power supply and
output connectors use 1 thread 2x0.75 mm2 cable. For the connection of input/output connectors use 0.50 mm2 1 thread cable.
14
1.7 Light Emitting Indicators Functionality
Connection Strength Indicator
To identify connection strength GSM indicator is used. To ensure the best quality of the network adjust the position of GSM
antenna and find the best possible connection by watching the frequency of indicator blinking.
GSM indicator blinking
Meaning
Off
No connection
Every 3 seconds
The connection is not reliable
Every second
Satisfactory
Several times per second
Good
Indicator is lit
Excellent
It is recommended to install the antenna remotely from communicator panel. Thus you will ensure better quality of audio
signal. We do not recommend installing the antenna in a metal box.
It is also used few others indicators – device activity indicator STATUS and working mode indicator INFO.
Device Activity Indication
STATUS indicator blinking
Meaning
Off
No power supply or some fault is present
Blinking several times per second
SIM card is used improperly/is not used
Indicator is lit
The device is working properly and ready for use
Working Mode Indication
INFO indicator blinking
Reikšmė
Off
The device is in passive mode
Blinking several times per second
The device retransmits the data sent from Security Control Panel to the panel of security service.
(this indication is possible then device is working
in first mode)
Indicator is lit
The device decodes the data sent via CONTACT
ID protocol to textual, user-understandable
information.
User manual ELDES ET07 v1.0
15
2. System Pre-operation
Communicator ET07 can operate in 3 modes:
1.
Informing security service mode – transmits information from the Alarm Control Panel via GSM audio connection
signal only to security service panel;
2.
Informing users via SMS messages mode – transmits information from the Alarm Control Panel via SMS messages only
to registered users;
3.
Informing security service and user mode – transmits information from the Alarm Control Panel via GSM audio connection signal to security service panel as well as to registered users via SMS messages.
This chapter describes pre-operation and system operation when each of the above mentioned modes is enabled.
Attention:
On the Alarm Control Panel you should enable tonal (DTMF) number dialling mode, activate CONTACT ID or 4+2 data transmission protocol and enter telephone number of security service panel.
Attention:
It is also necessary to enter telephone number of security service on the Alarm Control Panel when you do not need to transmit
data to security service and you are using only SMS messaging mode. In such a case you can use any telephone number (you can
use the number consisting of one digit).
2.1 Informing Security Service Mode
If you want the device to operate in this operating mode you must ensure that all connectors in connector group SET-MODE-PROG are not short-circuited (jumper is not used).
When this mode is enabled communicator ET07 only retransmits data sent from Alarm Control Panel via
CONTACT ID or 4+2 protocol to security service panel via GSM audio connection channel. The device does
not require any additional configurations.
SET
MODE
PROG
2.2 Informing Users via SMS Messages Mode
This operation mode is enabled by putting a jumper on MODE connectors in connector group SET-MODE-PROG (as demonstrated in the example). Other connectors must not be short-circuited.
When this operation mode is used the information about the secured object is delivered only to user
(users) and security service is not informed. In this case the device decodes the data sent from the Alarm
Control Panel via CONTACT ID protocol to user-understandable text and sends it via SMS message. This
decoding is performed according to the preset parameters which can be specified by the user only by using
the program ET07 Configuration Tool (for more information please refer to user manual of this program). SMS
messages can be received by up to 5 users.
SET
MODE
PROG
2.3 Informing Security Service and Users via SMS Messages Mode
This operation mode is enabled by putting a jumper on SET connectors in connector group SET-MODEPROG (as demonstrated in the example). Other connectors must not be short-circuited.
When this operation mode is used the information about the secured object is received by the user
(users) as well as security service. Device retransmits the data sent from the Alarm Control Panel via CONTACT ID protocol to the panel of security service and decodes this data to user-understandable text and
sends it via SMS message (indicator INFO informs only about decoding).The text is created by the user. This
decoding is performed according to the preset parameters which can be specified by the user only by using
the program ET07 Configuration Tool (for more information please refer to user manual of this program).
SMS messages can be received by up to 5 users.
16
SET
MODE
PROG
3. Appendix
3.1 Restoring Factory Default Parameters
To restore factory default parameters:
•
disconnect power supply;
•
short circuit (connect) connectors DEFAULT;
•
connect power supply for 5 seconds;
•
disconnect power supply;
•
disconnect connectors DEFAULT.
3.2 ET07 Configuration Program
System configuration is performed by using program software ET07 Configuration Tool that can be downloaded from internet
website www.eldes.lt
Before connecting the cable to the computer via USB (or RS232 type) port read ET07 Configuration Tool user manual that can be
found in HELP section of the program.
3.3 Technical Support
Indicator STATUS is off and not blinking
•
•
•
•
no external power supply
circuit not properly connected
blown fuse
no network signal
Indicator STATUS is blinking several times per second
•
•
•
SIM card is not inserted
SIM card PIN code request has not been disabled
SIM card not active
System does not deliver any SMS messages
•
•
•
•
•
SIM card account depleted
incorrect SMS central number
no network signal
user telephone number is not programmed in users list
user telephone number is indicated improperly (read more
about it in ET07 Configuration Tool user manual which can
be founf in Help section of the program)
If your problem could not be fixed by the self-guide above, please contact your distributor or ELDES technical support by e-mail
[email protected] More up to date information about your device and other products can be found at the manufacturer’s website
www.eldes.lt
User manual ELDES ET07 v1.0
17
Pagaminta Lietuvoje. Made in Lithuania. Сделано в Литве.
www.eldes.lt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement