User Manual v.1.2
User Manual v.1.2
Safety instructions
Pleasereadandfollowthesesafetyguidelinesinordertomaintainsafetyofoperatorsandpeople around:
•
•
•
•
•
•
AlarmsystemELDESEPIR(laterreferencedassystemordetector)hasradiotransceiver
operating in GSM900 and GSM1800 bands.
Don’tusethesystemwhereitcanbeinterferewithotherdevicesandcauseanypotential danger.
Don’tusethesystemwithmedicaldevices.
Don’tusethesysteminhazardousenvironment.
Don’t expose the system to high humidity, chemical environment or mechanical impacts.
Don’tattempttopersonallyrepairthesystem.Anysystemrepairsmustbedoneonlyby
qualified, safety aware personnel
Thesystemmustbepoweredbypowersupplysourceshouldnotexceed15VApower
supplywhichmustbeapprovedbyLSTEN60950-1standard
AnyadditionaldeviceconnectedtotheELDESEPIRsystemmustbepoweredupbya
LSTEN60950-1approvedsupply
External power supply can be con15V
nected to AC mains only inside
AC/DC
installation room with automatic
Dvipolė automatinė apsauga
2-pole circuit breaker capable of
L
disconnectingcircuitintheevent
N
of short circuit or over-current
condition. Open circuit breaker
musthaveagapbetweenconnectionsofmorethan3mm.
230V AC
Mainspowermustbedisconnectedbeforeanyinstallationortuningworkstarts.The
system installation or maintenance must not be done during stormy conditions.
Thesystemmustbeusedonlywithapprovedback-upbatterytoavoidfireorexplosion hazards. Special care must be taken connecting positive and negative battery
terminals.
Electrical socket from which the system is powered must be in an easily accessible
place.
EN
Thedeviceispoweredbyabackupbattery.Thedeviceisswitchedoffbyunplugging
external electrical power supply and disconnecting battery connector which is accessed by opening device frame cover.
FuseF1type-C1S2.5A.Blownfusecannotbereplacedbytheuserandthereplacementfuseshavetobeexactlythesameasindicatedbythemanufacturer.
WARNING:inordertoavoidfireorexplosionhazardsthesystemmustbeusedonly
withapprovedback-upbattery.Specialcaremustbetakenwhenconnectingpositive
and negative battery terminals
TheWEEE(WasteElectricalandElectronicEquipment)markingonthisproduct(see
right)oritsdocumentationindicatesthattheproductmustnotbedisposedoftogetherwithhouseholdwaste.Topreventpossibleharmtohumanhealthand/ortheenvironment,theproductmustbedisposedoninanapprovedandenvironmentallysafe
recyclingprocess.Forfurtherinformationonhowtodisposeofthisproductcorrectly,
contactthesystemsupplier,orthelocalauthorityresponsibleforwastedisposalin
your area.
Copyright©“ELDESUAB”,2009.Allrightsreserved
Itisnotallowedtocopyanddistributeinformationinthisdocumentorpasstoathirdparty
withoutadvancedwrittenauthorizationby“ELDESUAB”“ELSDESUAB”reservestherightto
updateormodifythisdocumentand/orrelatedproductswithoutawarning.Hereby,ELDES
UABdeclaresthatthisGSMAlarmSystemELDESEPIRisincompliancewiththeessential
requirementsandotherrelevantprovisionsofDirective1999/5/EC.
Thedeclarationofconformitymaybeconsultedatwww.eldes.lt/ce
Limited Liability
Thebuyermustagreethatthesystemwillreducetheriskoffire,theft,burglaryorotherdangersbutdoesnotguaranteeagainstsuchevents.
“ELDESUAB”willnottakeanyresponsibilityregardingpersonalorpropertyorrevenueloss
whileusingthesystem.
“ELDESUAB”liabilityaccordingtolocallawsdoesnotexceedvalueofthepurchasedsystem.
“ELDESUAB”isnotaffiliatedwithanyofthecellularprovidersthereforeisnotresponsiblefor
thequalityofcellularservice.
Manufacturer Warranty
Thesystemcarriesa24-monthwarrantybythemanufacturer“ELDESUAB ”.
Warrantyperiodstartsfromthedaythesystemhasbeenpurchasedbytheenduser.Thewarrantyisvalidonlyifthesystemhasbeenusedasintended,followingallguidelineslistedinthe
manualandwithinspecifiedoperatingconditions.Receiptmustbekeptasaproofofpurchase
date.
Thewarrantyisvoidedifthesystemhasbeenexposedtomechanicalimpact,chemicals,high
humidity,fluids,corrosiveandhazardousenvironmentorotherforcemajeurefactors.
Package content:
1. ELDES EPIR ............................................................................................. qty. 1
2.GSMantenna.......................................................................................... qty. 1
3.PowerSupply. ........................................................................................ qty. 1
4. ELDES EPIR User Manual .................................................................... qty. 1
5.MicroUSB-USBcable(onlyfromELDESEPIRv2version)....... gty. 1
About User Manual
ThisdocumentdescribesalarmsecuritysystemELDESEPIRinstallationandoperation.
ItisveryimportanttoreadUserManualbeforestartusingthesystem.
A quick start guide is located in first two chapters. Chapter 3 and 4 describe additional system
capabilities.
22
EN
CONTENT
1. General Information
1.1
1.2
1.3
1.4
1.5
Functionality................................................................................................................................................ 24
Operationdescription .............................................................................................................................. 24
Technicalspecifications .......................................................................................................................... 25
Main functions ........................................................................................................................................... 25
Systeminstallation .................................................................................................................................... 26
2. System pre-operation and essential control commands
2.1 SelectingdevicelanguageandverificationofSMScentralnumber ...................................... 28
2.2 Passwordchange ...................................................................................................................................... 29
2.3 Usernumbers .............................................................................................................................................. 29
2.3.1 SavingorChangingnumbers .............................................................................................. 30
2.3.2 Verificationofsavednumbers .............................................................................................. 30
2.3.3 Deletionofsavednumbers................................................................................................... 30
2.4Dateandtimesettings ............................................................................................................................... 31
3. Additional system capabilities
3.1 Renamingsecurityzones..................................................... ................................................................... 32
3.2 SystemandZonestatus .......................................................................................................................... 32
3.3 Exittime-outconfiguration.................................................................................................................... 32
3.4 InfoonstatusSMS............................................................. ....................................................................... 33
3.5 Blockingunknownincomingnumbers............................................................. ................................ 34
3.6 Externalpowersupplycontrol. ............................................................................................................. 34
3.7 EnablingRemoteMicrophonelistening .......................................................................................... 34
3.8 SMSmessagedeliverytomultipleusers ........................................................................................... 35
3.9 SMSmessageinformingaboutsystemarming/disarming ....................................................... 35
3.10 Settingdetectorsensitivitylevel.......................................................................................................... 35
4. Appendix
4.1
4.2
4.3
4.4
Restoring default parameters .............................................................................................................. 36
ELDESEPIRConfigToolconfigurationsoftware .............................................................................. 36
Replacingback-upbattery ................................................................................................................... 36
Technicalsupport ..................................................................................................................................... 37
USERMANUALV.1.2
23
1. General Information
1.1 Functionality
ELDESEPIR–microcontrollerbasedsecuritysystemforhouses,cottages,countryhomes,garages
andotherbuildings.
Thesystemcanbeusedinfollowingapplications:
• Propertysecurity
• Mains230VpowerstatuswithSMSmessage
• Remotelisteningofwhatishappeninginthesecuredpropertywithbuiltinmicrophone
Alsocapableofinforminguseraboutmains230VpowerstatusovercellularGSMnetwork.
1.2 Operation Description
SecurityalarmsystemELDESEPIRworkswithGSMnetwork.Thesystemisarmedordisarmed
byacallfromyourmobilephonewhichdoesn’tincuranycost.Toarmordisarmthealarmsystem
theuserhastocalltothenumberoftheSIMcardinsertedinELDESEPIRdevice.Beforedoingthis
itisnecessarytochangethedefaultpasswordandenteratleastoneuser.
Whenalarmsystemnumberhasbeendialedandringingisdroppedafterthreecallsignals–
meansthesystemwassuccessfullyarmed.Ifringingisdroppedafteronlyonecallsignal–system
disarmed.Theusershouldwaituntilthesystemdropscallsautomatically.
TheuserlistedasNr.1getsshortSMSmessageeachtimethesystemissuccessfullyarmedor
disarmed.Whensystemisarmedviaphonecall,thereis15seconddelaybeforeactivation,meant
for leaving premises.The time delay is user configurable parameter (see chapter 3.3). Red light
emitting diode indicator (LED) located on detector lense will start to blink informing that time
delayhasbeenengagedandusermustleaveroom.Theredlightgoesoffupontime-outdelay
expiration and system is engaged.
When detector is disarmed and motion is detected in the room, LED on the lense will be
turnedonshortly.
Whendetectorisarmedandupondetectionofmotion,systemwillsendSMSmessageuntil
successful delivery and ring preprogrammed numbers until user picks up or call expires. If user
answersthecall,remotemicrophonegetsactivatedforlistening.
SMSmessagecanbesenttoallpreprogrammedusers(seechapter3.8formoredetails).
Thesystemwillautomaticallyswitchtoback–upbatterysupplyincaseofmainspowerfailure,
andusergetsSMSwarningmessage.SMSmessagewillalsonotifywhenmainspowerisrestored
orback-upbatteryisabouttogetdischargedandsystemwillbeswitchedoff.
Theusercanalsoinquirethesystemaboutsystemstatus,powersupplystatus,networkquality
aswellasconnectandlistenthrougharemotemicrophone.
ThesystemwillignorerequestscomingfromunknowntelephonenumberorSMSmessage
withwrongpassword.WithcorrectpassworduserhasthecapabilitytoaccesssystemmanagementfromanyGSMphone(notnecessarypre-programmed).Seemoredetailsinchapter3.5.
24
EN
1.3 Technical Specifications
Electrical and mechanical specifications
15V
SupplyVoltage
Back-upBatteryvoltage,capacity
Back-upBatterytype
GSM modem frequency
Dimensions
Operating temperature range
Back-upbatteryoperatingtime
Detection angle
Maximum detection range
500mAmax
8.4V;150-250mAh
Ni-Mh
900/1800Mhz
104x60x33mm
-10…+40oC
upto6hours
90°
10 meters
1.4 Main Functions
7
9
5
1
3
13
10
12
4
2
6
Short description
of main functions:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
ELDESEPIRholderusedforwallfixing
SIMcardsocket
DetectorlensewithLEDindicatorlight
ELDES EPIR sensor
Powersupplysocket
Powersupply
Power supply connector
Buttontorestoredefaultparameters
SMA type connector for GSM modem
Microphone
Holderfixingplace
BackupBattery
Micro-USBconnector
(onlyfromELDESEPIRv2version)
8
9
11
BACK SIDE
USERMANUALV.1.2
25
1.5 System installation
The system should be installed indoors. Choose location where unauthorized entry is most
likely.
To avoid fault alarms, avoid installing in following locations:
• locatinglenstowardsdirectsunshine,e.g.facingwindows
• neardeviceswithhightemperaturefluctuations,e.g.fireplaceorheatingboiler
• placeswithincreaseddustorairflowtraffic
• metalorshieldedwallwhereGSMconnectionmightbelost
PlaceSIMcardinthemobilephoneandmakesurethatSIMcardPINcodeisdisabledbyfollowingappropriatemenus.SIMcardshouldnothaveanyremainingSMSmessages.
RECOMMENDATION
ItisworthtochoosethesameGSMcellularproviderasmostusersuseassuringfastandreliableSMSmessagedeliveryandphonecallconnection.
RECOMMENDATION
To increase system reliability, it is recommended not to use prepaid SIM cards.The system
would fail to send any messages upon depletion of prepaid account. Also it is recommended
to disable call forwarding and voice mail.
EN
1. Fixtheholderto
thewall
2. InsertSIMcard
withPINcode
disabled
3. Connect
antenna
4. Plug power
supply
connector
5. PlaceELDES
EPIRintothe
holder
6. Plugpower
supply into
mains socket
7.Thesystemstartsin1-2minutes.WhenLEDisoff,moveyourhandinfrontofELDESEPIRlense
andwatchthesystemdetectingmotionandturningonLEDforfewseconds.IfLEDindicator
isblinkingfast(fewtimesasecond),couldbethatSIMcardinnotinsertedproperlyorPIN
codehasnotbeendisabled.
* TheSIMcardisinsertedintotheslotfacingthecutend.SIMcardcontactsshouldface
ELDESEPIRlowercover.AfterinsertingSIMcardpushitinuntilyouhearaclick.Inthisway
thecardlocksintheslot.IfyoudonothearaclickcheckifyouinsertedSIMcardcorrectly.
Donotuseexcessiveforce.ToremoveSIMcardfromtheslotpushitin.Youshouldhearthe
clickagainandSIMcardshouldcomeoutfromtheslot.
USERMANUALV.1.2
27
2. System pre-operation
and essential control commands
VERY IMPORTANT!!!
Underscoresymbol‘_’inthismanualisusedtorepresentspace.WhenwritingSMSmessages,
everyunderscoresymbolshouldbereplacedbysinglespacesymbol.XXXX–meanspassword.
Don’tleaveanyspaceatthebeginningandtheendofthemessage.
TosetELDESEPIRsystemparameterseasierandquickeryoucanusethecomputer,USBcable
andconfigurationprogramELDESEPIRConfigTool.Youcanreadmoreinchapter4.2.
2.1 Selecting device language and
verification of SMS central number
Thelanguageinwhichthedevicecommunicateswiththeusercanbe
chosenbeforechangingfactorydefaultpassword.Tochangethelanguageinthesystemthatisalreadyconfiguredresetdefaultsettingsas
described in 4.1 appendix.
SendSMSmessagewiththerequiredlanguagecodetothenumberof
theSIMcardinsertedinELDESEPIR.
Table of possible
languages
Language
Code
lithuanian
LT
english
EN
russian
RU
E.g., if you want to set the English language send the following SMS message: EN
30-60secondslateryoushouldgetanSMSmessage:„Englishlanguageconfirmed.“Gotochapter2.2
uponreceptionofthismessage.
OtherwisecheckfornetworkconnectionandcallELDESEPIRsystemfromyourmobileandwaituntil
thesystemdropsthecall.YoushouldgetanSMSmessageaskingtochangedefaultpassword.OtherwisecheckfornetworkconnectionandchangeSMScentralnumber.
SMScentralnumberissavedinSIMcard,thereforeifSIMcardhasbeenusedtosendSMSmessageswithamobilephone,thenyoudon’t’needtochangeSMScentralnumber.OftenSMScentral
number is already saved in SIM card by cellular operator.
28
EN
Central number can be entered by sending SMS message:
XXXX_SMS_+37011111111
XXXX–isapassword.Defaultpasswordisfourzeros:0000.SMScentralnumberisprovidedbycellular
network provider.
Example: 0000_SMS_+37069899992
MessageshouldbesenttothenumberofSIMcardwhichisplacedintothesystem.Ifallwentcorrect,
thesystemwillsendamessage:SMS central number has been successfully changed to +37011111111
2.2 Password change
All SMS commands start with a password, so please memorize it
well. Manufacturer default password is four zeros 0000, which
is necessary to change. Manufacturer default password can be
changedbysendingSMSmessagetoELDESEPIR:
0000_
PSW_1111
0000_PSW_XXXX
To replace your password, send SMS message:
YYYY_PSW_XXXX
XXXX–anyfourdigitnumberexceptfourzeros.Non-numericalcharacterslikedots,colons,spaces
arenotallowed.YYYY–oldsystempassword.
E.g. 0000_PSW_1111
Defaultmanufacturerpasswordcanberestored,seechapter4.1formoredetails.
2.3 User numbers
SystemELDESEPIRallowstopre-programuptofivedifferentmobilenumberswhichwillhave
access to and controls the system. Number NR1 is mandatory while others can be skipped. All
numbersmustbeenteredstartingwithinternationalcountrycode.E.g.nationalcodeforLithuania
is370,UK–44.Numbersshouldbeenteredbasedonpriority,sincethesystemwilltrytocontact
firstenterednumberandincaseoffailurewillfollowwithsecondandsoon.
USERMANUALV.1.2
29
2.3.1 Saving or Changing numbers
SendSMSmessagewithtexttoELDESEPIR:
XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_
NR4:37011111111_NR5:37011111111
Onesshouldbereplacedwithusernumbers.Numbersdon’thave
tobeenteredallorinsequentialorderrightaway.E.g.usecanenterfirstandfourthnumberbysendingfollowingSMSmessage:
XXXX_NR1:37011111111_NR4:37011111111
0000_NR1:
37011111
111
Or individually one number at a time:
XXXX_NR3:37011111111
Numbers can be changed same way as described above. New number will overwrite old one,
thereforenoerasingisnecessary.
E.g. 0000_NR1:37011111111
2.3.2 Verification of saved numbers
Toinquirethesystemaboutpre-programmednumbers,sendSMS
message:
0000_
HELPNR
XXXX_HELPNR
E.g. 0000_HELPNR
Thesystemwillreplywithallpre-programmednumbers.
2.3.3 Deletion of saved numbers
Pre-programmed numbers can be erased by sending SMS message
withnumberstobeerased.
XXXX_NR2:DEL_NR3:DEL_NR4:DEL_NR5:DEL
ToeraseNR2sendfollowing:
E.g. 0000_NR2:DEL
ThesystemwillnotallowerasingfirstnumberNR1.Itcanonlybechanged.
0000_
NR2:DEL
EN
2.4 Date and time settings
Itisimportanttosetcorrectdateandtime,sothatthesystemcansendreportsatspecifiedtimes.
Date and time can be set by sending following format SMS message:
XXXX_MMMM.mn.dd_hh:mi
WhereMMMM–meansyear,mn–month,dd–day,hh–hour,
mi–minutes
0000_
2009.01.
01_14:15
E.g. 0000_2009.01.01_14:15
USERMANUALV.1.2
31
3. Additional system capabilities
3.1 Renaming security zones
Manufacturerinitiallysetfollowingzonenames:Z1-Motion.Userisfreetochangeanyofthese
nameskeepinginmindthatnamescannotbesameormatchsystemcommands.
ZonenamescanbechangedwithfollowingSMSmessage:
0000_Z1:NewZoneName
0000_Z1:
passage
Zonenamescanhaveupto14characters.
E.g. 0000_Z1:passage
3.2 System and Zone status
To find out current zone names, settings and status, send SMS message
XXXX_STATUS
Thesystemwillreply,e.g.System is armed/disarmed Z1:MOTION:ON/OFF
ON- means enabled. OFF- disabled
3.3 Exit time-out configuration
Whensystemisarmed,theusershouldleavepremiseswithinspecifiedtime(manufacturerdefault
15seconds).Duringthisperioddetectorignoresmotion.Runningtime-outisindicatedbyblinking
LED(onceasecond).
Time-outperiodcanbeconfiguredwithSMSmessage:
XXXX_INOUT:SSO
WhereSSO–exittime-outinseconds.
Thereisnotime-outifperiodissetto0.
32
XXXX_
INOUT:30
EN
3.4 Info on status SMS
Security system EPIR can be inquired at any time about its status, signal strength, zone status.
At the same time system can be tested. If SMS response message is received, means system is
functioning properly.
ThisisalsousefulforuserswithprepaidSIMcards.ItcanbecheckedwhetherSIMcardhasenough
remaining balance for sending SMS. Send SMS message:
XXXX_INFO
0000_INFO
E. g. 0000_INFO
TheresponseSMSmessagewillbereceived,e.g.2008.08.07 11:15
System armed/disarmed Signal Strength Fair. Z1:OK/ALARM
Where OK – if zone has not been activated, ALARM – if been activated
Bydefault,thisstatusSMSmessagewillbesentdailyat11:00inthe
morning.TheseparameterscanbeconfiguredwithSMSmessage:
XXXX_INFO:PP.VV
0000_INFO:
01.10
PP–messageperiodindays,validvalues[00–10]
VV-timewhenmessageissent,validvalues[00–23]
E.g XXXX_INFO:01:10, meansthatstatusmessagewillbesentevery1
dayat10:00.IfPPvalueis0,andVVintherangeof[1-23],thenperiodic
statusmessageswillbesentmultipletimesperday,withperiodbeing
specifiedasVVtime.
E.g. XXXX_INFO:0.2, meansthatstatusmessagewillbesentevery
2hours.
0000_INFO:
0.2
To disable periodic status messages, send SMS:
XXXX_INFO:00.00
E.g. XXXX_INFO:00:00
The status messages will not be sent until enabling or restoring
default parameters.
USERMANUALV.1.2
0000_INFO:
00.00
33
3.5 Blocking unknown incoming numbers
Bydefault ELDES EPIRcanbecontrolled fromanyofthepre-programmed n umbers NR1..NR5.
Butusercanaccessthesystemandcontrolparametersfromanynumber aslongaspassw ord
is know.
Toenablethisfeature,sendSMSmessage:
XXXX_STR:ON
0000_STR:
ON
E. g. 0000_STR:ON
Todisablethisfeature,sendSMSmessage:
XXXX_STR:OFF
3.6 External power supply control
ThesystemELDESEPIRwillreporteverytimemains230Vpowersupplyfailsorrecovers.Insome
remoteplaceswheremainspowersupplyisunreliable,thesystemcanbeconfiguredtoignore
thesechanges.SendSMS:
XXXX_M:OFF
E.g.. 0000_M:OFF
0000_M:
OFF
Or it can be enabled by SMS message:
XXXX_M:ON
3.7 Remote Microphone listening
To be able to listen what is going on in remote house can be done in two different ways:
1. Whenalarmhasbeenactivated,thesystemwillringpre-programmednumbersanduser
cananswerthecall.Remotemicrophonewillbeenabledforlistening.
2. BysendingSMSmessage
XXXX_MIC
ThesystemwillringthesenderofformerSMS,anduponanswering thecall,usercanlisten
toanysounds inthebuilding.Thephone callmustbeanswered within 20seconds otherwisethesystemwillstoptryingandreturntopreviousstate.
EN
3.8 SMS message delivery to multiple users
Uponactivatedalarm,SMSmessagesarerepeatedlysentuntilfirstsuccessfuldeliverytooneofthe
users.SystemstartswithNR1,andifdeliveryfails,followswithNR2,etc.
ItisalsopossiblethatSMSmessagewillbesenttoallrecordedusers.
Toenablethisfunction,sendSMSmessage:
XXXX_SMSALL:ON
Todisablethisfunction,sendSMSmessage:
XXXX_SMSALL:OFF
3.9 SMS message informing about system arming/disarming
BydefaulttheuserNR1willreceiveashortmessageeverytimesystemisarmedordisarmed.To
disablethisfunction,sendSMSmessage:
XXXX_MASTER:OFF
Tore-enablethisfunction,sendSMSmessage
XXXX_MASTER:ON
3.10 Setting detector sensitivity level
Themanufacturerhassetoptimaldetectorsensitivitylevel.However,insomecasesthesystemis
installedinwindypremiseswheretheairflowcancausefalsealarms.
Insuchcasessensitivitylevelcanbereduced.
Inordertoincreaseorreducemotiondetectorsensitivitytheuserhas
tosendthefollowingtextmessagetothesystemELDESEPIR:
XXXX
LEVEL:XX
XXXX_LEVEL:XX
whereXXisatwo-digitnumberthatcanbe[20-99].Factorydefault
valueis40.Thegreaterthenumbervalue,thelowerdetectorsensitivity level.
InordertofindoutthesetsensitivityleveltheusershouldsendthefollowingSMSmessage:
XXXX_LEVEL
USERMANUALV.1.2
35
4. Appendix
4.1 Restoring default parameters
Torestoresystemdefaultparameters,pressandholdon~5secondsbuttononthebacksideof
detectorusinganeedleorothersharppointeddeviceuntilLEDwillblink5times.
4.2 ELDES EPIR ConfigTool configuration software
ConfigurationprogramworksonlywithELDESEPIRdevicesstartingwithv2version.
Toconfigurethesystemquickerandeasieraswellasusemoresystemcapabilitiesuseconfigurationprogram„ELDESEPIRConfigTool”whichcanbedownloadedfromourwebsitewww.eldes.lt
BeforeconnectingUSBcabletothecomputerreadELDESEPIRConfigTooluserguideavailablein
theprogramchapterHELP.
4.3 Replacing back-up battery
Normallyrealback-upbatterywilllastatleast2years.Thislargelydependsonsurroundingtemperature and frequency of mains power disruptions.
To change back-up battery, follow these steps:
1. Unplug power supply form mains power
2. RemoveELDESEPIRfromholder
3. Unplugpowersupplyconnector
4. RemovescrewlocatedonthebacksideofELDESEPIR
5. OpenELDESEPIRenclosure
6. Carefullyremoveback-upbattery
7. Withonehandholdingback-upbattery,unplugbatteryconnector
8. Replacebattery.Usebatterytypeasspecifiedintechnicalspecifications.
9. Repeat all steps in inverse order
EN
4.4 Technical support
Indication
Possible reason
Lense indicator OFF
· Nomains230Vpower
· Power supply connector unplugged
· out of coverage or to weak signal.
Indicator is blinking once a second
· missing SIM card
· PINcodehasn’tbeendisabled
· SIM card not active
System does not send any SMS
messages and/or does not ring
· SIM card account depleted
· Incorrect SIM central number
· No network signal
· Usernumberisnotprogrammedin(ordisabled
accessfromunknownnumbers)
Received SMS message
“IncorrectFormat”
· Wrong syntax
· Could be space left in wrong SMS message place
· Manufacturerdefaultpasswordnotchanged
· Missing user NR1
Ifyourproblemcouldnotbefixedbytheguideabove,plea[email protected]eldes.lt
Moreuptodateinformationaboutyourdeviceandotherproductscanbefoundatmanufacturer’s
website www.eldes.lt
USERMANUALV.1.2
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement