Shine series Solar controller User Manual-En Ver
Lumiax”
Shine series
Solar charge controller
6A/10A
User Manual
Lumiax Qingdao
www.Lumiax.com
[ISO9001:2008
CE, RoHS
Solar Charge Controller Shine06/10 User Manual
Solar charge controller
Dear Clients,
Thanks for selecting the Shine™ series solar controller. Please take the time to read this user manual, this will help you to make
full use of many advantages the controller can provide your solar system.
This manual gives important recommendations for installing and using and so on. Read it carefully in your own interest please.
1.Description of Function
Shine series solar controller is specifically designed to meet
the needs of solar home systems. It provides the best cost-
effective.
It comes with a number of outstanding features, such as:
® Low cost and high reliability design
e 12V/24V automatic recognition
e Clear readable display of charge/discharge and error
description
e Temperature compensation
e Four stage charge way: fast, boost, equalization, float
e Full automatic electronic protect function
Instructions and waiver of liabilit
2.1 Safety
@The solar charge controller may only be used in PV
systems in accordance with this user manual and the
specifications of other modules manufacturers. No
energy source other than a solar generator may be
connected to the solar charge controller.
@Batteries store a large amount of energy, never short
circuit a battery under all circumstances. We strongly
recommend connecting a fuse directly to the battery to
protect any short circuit at the battery wiring.
(Batteries can produce flammable gases. Avoid making
sparks, using fire or any naked flame. Make sure that the
battery room is ventilated.
@Avoid touching or short circuiting wires or terminals.
Be aware that the voltages on special terminals or wires
can be as much as twice the battery voltage. Use
isolated tools, stand on dry ground, and keep your
hands dry.
©Keep children away from batteries and the charge
controller.
2.2 Liability Exclusion
The manufacturer shall not be liable for damages,
especially on the battery, caused by use other than
as intended or as mentioned in this manual or if the
recommendations of the battery manufacturer are
neglected. The manufacturer shall not be liable if
there has been service or repair carried out by any
unauthorized person, unusual use, wrong
installation, or bad system design.
3. Dimensions
150
3.5
o EJ ól — 10
| |
4. Installation
The following diagrams provide an overview of the
connections and the proper order.
® Shine series
L u m I a X Solar Charge Controller
| +
О
№ To avoid any voltage on the wires, first connect the wire to
the controller, then to the battery, panel or load.
H Make sure the wire length between battery and controller
is as short as possible.
H Recommended minimum wire size: Shine06: 1.5 mmz;
Shine10: 2.5mm?.
H Be aware that the positive terminal of Shine are connected
together and therefore have the same electrical potential.
If any grounding is required, always do this on the positive
wires.
EM Connecting capacitive load may trigger short circuit
protection.
rd
battery negative on the chassis, loads connected to the
controller must not have an electric connection to the car
body, otherwise the Low Voltage disconnect and electronic
fuse functions of the controller are short circuited.
Remark: If the device is used in a vehicle which has the
Page 1 of 3 pages
Solar Charge Controller Shine06/10 User Manual
5.Starting up the controller
5.1Self Test
As soon as the controller is supplied with battery,
it starts a self test routine. Then the display changes
to normal operation.
5.2System Voltage
The controller adjusts itself automatically to 12V
or 24V system voltage. As soon as the battery
voltage at the time of start-up is within 10V to 16V,
the controller implies a 12V system, else if the
battery voltage is within 20V to 30V, the controller
implies a 24V system.
If the battery voltage is not within the normal
operating rang(ca.10 to 16V or ca.20 to 30V)at start-
up, a status display according to the section 7.2
Error description occur.
5.3Battery Type
The Shine series controller applies to Liquid and
Gel battery, the factory default setting is suitable for
liquid battery.
6.Display Functions
The controller is equipped with 5 LEDS.
In normal operation, the controller shows charge or discharge
status, battery capacity and load status.
PA ‘Gy
6.1 Battery Capacity display :
Yellow
Red NB 7, Green
Red On, Energy of Battery <25%
Yellow On, Energy of Battery 25-75%
Green On, Energy of Battery >75%
LP
until low voltage disconnect in relation to a fully charged
battery.
The percentage corresponds to the available energy
6.2 Charge & Error display (INFO) :
Red Green
INFO
INFO Green On, is charging, else is discharge ;
INFO Red On, is Error Status, according to the section 7.2
Error description.
7.Safety Features and Error description
7.1 Safety features
Solar terminal | Battery terminal | Load terminal
Reverse
polarity Protected *1 |Protected *1 Protected *2
но, a Switches off
Short circuit Protected Protected *3 immediately
Switches off
Over current| — — with delay
Reverse
Current Protected — —
Over voltage|Max.55V *4 | Max. 40V —
Under
voltage — — Switches off
Over temp switches off the load if the temperature
"| reaches the set value.
*1 Controller can not protect itself in a 24V system when
polarity of battery or solar is reversed.
*2 Controller can protect itself, but loads might be damaged.
*3 Battery must be protected by fuse, or battery will be
permanently damaged.
*4 The solar panel voltage should not exceed this limit for a
long time as voltage protection is done by a varistor.
Warning: The combination of different error
conditions may cause damage to the controller.
Always remove the error before you continue
connecting the controller.
7.2 Error description
Error Display |Reason Remedy
Red .
Ze Load will reconnect
[a]
Loads "| Battery is low [as soon as battery
ot Red LED is recharged
no |
. Red
supplied nro] Over current/ Switch off all loads.
RedLED [short circuit Remove short
Batt . Red —
attery is ela
empty after nd Battery has Change battery
. RedLED |low capacity
a short time| .
IS ON
Battery i is Red Сгееп
not bein | 8) wel soaramay fauty [T0000
due Green LED| Or Wrong polarity ;
the day of reverse polarity
Battery voltage Check if other
= y 9 sources overcharge
Over e- “too high the battery.
voltage Red(INFO) |(>15.5V/31V) If not, controller
protection [and is damaged.
Green(Bat.) | Battery wires or
LED are battery fuse Check battery
lighted damaged, battery battel use an
has high resistance attery.
Th ;
Does not The batte У + Charge or discharge
recognize All LED |... pin h | the battery to make
the syst ; within the norma h | ithi
ystem Lighted | operating ran the voltage within
voltage Р 9 7ang the normal range
at startup
Page 2 of 3 pages
Solar Charge Controller Shine06/10 User Manual
8.Low Voltage Disconnect Function
The controller uses state of charge to protect the
battery form being deeply discharged, Shine series
controller is disconnect at 11.0V/22.0V.
7 Note:
1. If the controller goes into low voltage protection, it will
restore only when the battery being recharged and the
voltage reaching the reconnect voltage.
2. Around oblique line value separately on behalf of 12V
and 24V system's value.
9.Technical Data
Model Shine06 | Shine10
System voltage 12V/24V automatic recognition
Max solar current or load current 6A 10A
Fast voltage 14.0V/28.0V (25°C)
Boost voltage 14.5V/29.0V (25°C)
Equalization voltage 14.8V/29.6V (25°C) ( Liquid )
Float voltage 13.7V/27.4V (25°C)
Load disconnect voltage 11.0V/22.0V
Load reconnect voltage 12.5V/25.0V
Battery type Liquid, Gel
Temperature compensation -4.17mV/K per cell (boost, equalization), -3.33mV/K per cell (float)
Max solar voltage 55V
Max battery voltage 40V
Over voltage protection 15.5V/31.0V
Dimensions/Weight 150x72x35mm / 130g
Wire size 06A: 1.5 mm?z; 10A: 2.5mm?
Own consumption 4mA
Ambient temperature -40% ~ +60 °C
Degree of protection IP22
Subject to change without notice. Version: DC27
Page 3 of 3 pages
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement