user manual

user manual
P/N 35010031-G
K1 HAZER
user manual
TM
Safety information...................................................................................................................... 3
Product overview ....................................................................................................................... 6
Product description................................................................................................................ 6
Features at a glance .............................................................................................................. 6
Product details ....................................................................................................................... 7
Quick Start ................................................................................................................................. 8
Setting up............................................................................................................................... 8
Making haze........................................................................................................................... 8
Shutting down........................................................................................................................ 8
Installation and setting up ......................................................................................................... 9
Location ................................................................................................................................. 9
AC power ............................................................................................................................... 9
Setting up............................................................................................................................. 10
Final checks ......................................................................................................................... 10
Turning on the power........................................................................................................... 10
Shutting down after use....................................................................................................... 10
Control settings ....................................................................................................................... 11
Overview .............................................................................................................................. 11
Fast access buttons............................................................................................................. 11
Setting haze density............................................................................................................. 11
Setting fan speed ................................................................................................................. 12
Auto fan mode...................................................................................................................... 12
Setting Run mode ................................................................................................................ 12
Setting the Timer.................................................................................................................. 12
Setting the DMX base address ............................................................................................ 13
Setting the master-slave link mode ..................................................................................... 13
Aux option ............................................................................................................................ 13
Priming the machine after fluid out ...................................................................................... 13
Resetting options to factory settings ................................................................................... 14
Remote control ........................................................................................................................ 15
Overview .............................................................................................................................. 15
Functions ............................................................................................................................. 15
DMX control ............................................................................................................................. 16
Overview .............................................................................................................................. 16
Connection........................................................................................................................... 16
DMX functions...................................................................................................................... 16
Fog fluid type........................................................................................................................... 17
Basic service............................................................................................................................ 18
Cleaning............................................................................................................................... 18
Fuse replacement ................................................................................................................ 18
Troubleshooting ...................................................................................................................... 19
Status messages ..................................................................................................................... 20
Specifications .......................................................................................................................... 21
Notes ....................................................................................................................................... 23
2
Safety information
Safety information
READ AND SAVE THESE INSTRUCTIONS
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Before operating the machine – Read and retain these Instructions
Avant l'opération – Lire et conserber ces instructions
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
Preventing electric shocks
•
Always ground (earth) the machine electrically.
•
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload-and ground-fault protection.
•
Before connecting the JEM K1 Hazer to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service for assistance.
•
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Martin Service for assistance. If the supply cord is
damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
•
Disconnect the machine from AC power before servicing and when not
in use.
Safety information
3
•
This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.
•
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
•
Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin.
•
Do not operate the machine if any parts are damaged, defective or
missing.
•
Moisture and electricity do not mix. Do not aim the haze output at
electrical connections or devices.
Preventing burns and fire
•
The haze produced by the machine is hot enough to cause burns when
it leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 1 meter (39 inches) away from the
haze output nozzle.
•
Do not touch the haze output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.
•
Haze output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point the haze output at sources of
ignition such as open flames or pyrotechnic effects.
•
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•
Provide a minimum free space of 100mm (4 inches) around the
machine.
•
Provide a minimum free space of 500mm (20 inches) around fans and
air vents and ensure free and unobstructed air flow to and around the
machine.
•
Keep the machine at least 600mm (24 inches) away from combustible
and heat-sensitive materials.
•
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•
Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
4
•
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•
Do not install the machine over areas where people are present.
•
This appliance is not intended for use by persons (including children)`
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•
Haze machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
Safety information
•
Ensure at least 2m visibility in areas where haze is being produced.
•
Haze fluid contains food-grade glycols in solution but may present
health risks if swallowed. Do not drink it. Store it securely. If eye contact
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.
Preventing breathing problems
•
A haze machine can operate safely only with the haze fluid it is
designed for. Use the machine only with the fluid specified under “Haze
fluid options” on page 17 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.
•
Do not create dense haze in confined or poorly ventilated areas.
•
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to haze output.
•
Do not point the haze output directly at a person’s face or at face height.
General warnings
•
Read instructions before use - Lisez les instructions avant l´emploi.
•
Keep output 60 cm away from people and surfaces - Maintenir la buse à
60 cm des personnes et des surfaces.
•
Avoid installing over people’s heads - Evitez d' installer au dessus des
personnes.
•
Use only Martin K1 Haze fluid - Utilisez que du fluide Martin K1.
•
Prolonged use may cause condensation to form; check floors and
surfaces regularly - Une utilisation prolongée peut causer la formation de
condensation; vérifiez les sols et les surfaces régulièrement.
•
May affect sufferers of severe respiratory disorders - Peut affecter les
victimes souffrantes de troubles respiratoires sévères.
•
Disconnect supply before opening case; refer servicing to qualified
personal - coupez l´alimentation avant d' ouvrir la machine; confiez
l´entretient à un personnel qualifié.
•
Not for domestic use - Pas fait pour une utilisation domestique
•
Surfaces may become very hot during use - Les surfaces peuvent
devenir trés chaudes pendant l' utilisation.
Safety information
5
Product overview
Product description
The JEM K1 Hazer™ from Martin is a top of the range solution to a wide variety
of atmospheric requirements whether permanently installed or taken on the
road.
Featuring a revolutionary new block design and a high volume radial blower, the
JEM K1 Hazer™ can quickly produce large volumes of haze to create large
scale effects in the biggest venues.
Congratulations on your purchase of the JEM K1 Hazer™ from Martin. Details of
the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
6
•
Attractive and rugged design
•
High speed radial blower
•
Revolutionary block design for high output and reliability
•
Control panel with alphanumeric display
•
Optional full function digital remote with display (25m max cable length)
•
Carrying handles
•
DMX control (2 channels)
•
Standby battery runs shutdown procedure after power down
Product overview
Product details
Fast access
buttons
Digital control
panel
3 pin DMX
input and
link
Remote
control
socket
5 pin DMX
input and
link
Main power
switch
Power inlet
connector
External fuse
Flying kit eyelet
mounting points
x4
Air intake
Fluid tank
Haze output
nozzle
Warning, high
temperature vapour and
surfaces!
Product overview
7
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of haze. This section tells you how to do that. However, please also make the
time to read the safety and servicing instructions in the remainder of this
manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the haze
output.
Fill the fluid tank with MARTIN-approved haze fluid (see page 17).
Connect a suitably rated power supply to the machine. The power requirements
are:
6.3A at 230V (EU) or 10A at 120V (US)
If you are using the optional remote control, connect it to the REMOTE IN
connector on the rear panel.
Turn on the main power switch located next to the power cable inlet.
Making haze
Press either ECO / PRE1 / PRE2 from the Fast Access Mode on the onboard
control panel. If using the optional remote control, press the HAZE button. The
display will show  for about 5-7 minutes, once heated the machine will
start to produce haze at the selected level. If the machine is new or has run out
of fluid, page 13 ‘Priming the machine’ should be referenced.
Shutting down
When you turn off the power, the unit will switch to its backup battery and enter
a 3 minute shutdown procedure. This clears the block of any residual fluid to
prevent clogging. During shutdown the display shows “WT” with a countdown.
8
Quick Start
Installation and setting up
DANGER! DO NOT operate the JEM K1 Hazer™ until you have read and
observed all the precautions listed under “Safety information” on page 3.
Location
The JEM K1 Hazer™ should be located on a solid surface such as the floor.
The machine can operate in any orientation from 45 degrees upwards to 45
degrees downwards. Steeper tilting may cause fluid leakage.
Do not suspend the machine over areas where people will be underneath.
Ensure that there is at least 100mm clearance all round the machine and at least
600mm in front of the haze output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• EU (230V) fit a plug rated 6 amp minimum
• US (120V) fit a plug rated 10 amp minimum
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the JEM K1 Hazer™ to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
6.3A at 230V (EU) or 10A at 120V (US)
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
Installation and setting up
9
Setting up
Fill the fluid tank with Martin approved fluid (see page 17).
If DMX control is being used, connect the machine to the DMX line (see page
16).
If the JEM K1™ Digital Remote is being used (optional accessory), connect the
remote to the Remote socket. (see page 16)
Final checks
Before applying power to the JEM K1 Hazer™, verify the following:
• the machine is safely located or installed and meets the location
requirements stated on page 9
•
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 3
•
the haze fluid is genuine Martin fluid listed under “Haze fluid options” on
page 17
•
the machine is electrically grounded (earthed)
•
the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power cable inlet and select
(Standby) from the  menu.
The display will show  for about 5-7 minutes as the machine heats up to
operating temperature and will then change to  (Ready).
You can then use the remote control, control panel or dmx signal to start haze
production.
Shutting down after use
When you turn off the power, the unit will switch to its backup battery and enter
a 3 minute shutdown procedure. This clears the block of any residual fluid to
prevent clogging. During shutdown the display shows “WT” with a countdown.
You can also shut down the machine by setting the  menu to . The 3
minute shutdown procedure will be activated. This can be done from the digital
remote or from the onboard control panel. The heater, fan and pump will be
shut down but the machine will remain powered and can be reactivated by
either following the steps above in ‘Turning on the power’ or following the ‘Quick
Start’ guide.
10
Installation and setting up
Control settings
Overview
By selecting either ECO / PRE1/ PRE2 from the Fast Access buttons below the
digital display at the rear of the unit allow you to quickly turn the haze on or off
at three different settings.
The digital display allows you to configure all options of the machine using
menus, if you need more detailed control.
Digital display

Menu previous/next
buttons
Value down/up
buttons
Enter/store button
Fast Access buttons
The four Fast Access buttons allow you to quickly set the machine to one of
three haze output levels and a Silent mode (SLNT). The display shows the
current setting.
If you press the same button again, haze output will stop and the machine will
go back to Ready mode. (SLNT) mode returns to previous state.
Fast Access
Mode
Haze and Fan settings

Drops Fan levels by 30% relative to
current values

DMX Value Equivalent
CH1
CH2
-
Reduce by 30%
of current value
Haze 5%, Fan 5%
30
11

Haze 50%, Fan 50%
120
110

Haze 100%, Fan 100%
219
219
Setting haze density
Use the Menu Previous / Next buttons to select the  option.
Use the Up/Down buttons to select the density from  – .
Press the Enter button to store the haze setting. The display shows .
The machine will only produce haze if the RUN menu is set to TIME or CONT.
(Or, if using the digital remote, if you press the Timer or Haze buttons).
If you want to temporarily change the haze density, do not press Enter.
The haze setting will go back to its stored value next time the machine
is powered up. This applies to all options.
Control settings
11
Setting Fan speed
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to select the fan speed from  – .
Press the Enter button to store the fan setting.
The fan will run continuously if set above 0% and the  menu is set to
,  or .
If haze is being produced and the fan is off or set to a low speed, the fan speed
will be automatically increased to prevent build-up of haze at the machine
output.
Auto Fan Mode
In some circumstances where an improved vertical distribution of haze is
required, can be selected from the menu. This causes the fan
speed to vary over a 5 minute period.
Setting Run mode
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to select the operating mode.
: heater off, fan off. Used when the machine is to be shut down.
: heater on, fan off. The machine is ready but not hazing
Fan on. Machine ready but not hazing.
: enable timed pulses of haze.
: enable continuous haze.
Press the Enter button to store the Run setting.
When the mode is changed to , the unit will enter a 3 minute shut down
sequence before powering down, to prevent block clogging. The display shows
 then  with a countdown. You can cancel the shut down sequence
by changing the run mode back to an active state.
Setting the Timer
If smaller amounts of haze are required the machine has an automatic timer to
give timed bursts of haze. You can set the “Run” and “Off” times independently
between 1 and 90 seconds.
Use the Previous / Next buttons to select the  or  option.
Use the Up/Down buttons to select the run or off time from  seconds to 
seconds. If you hold down the button the time will count up or down, getting
faster the longer you hold it.
Press the Enter button to store the timer setting.
To enable timer mode, select  from the RUN menu (or, if using the digital
remote, press the Timer button).
When the timer is running and the display is not showing a menu, the
display shows a countdown for the run time  and the off time
.
12
Control settings
Setting the DMX base address
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to set the DMX base address from  to . If
you hold down the button the address will count up or down, getting faster the
longer you hold it.
Press the Enter button to store the address setting.
The machine will automatically respond to a DMX controller whenever it is
connected.
Setting the master-slave link mode
It is possible to control several machines from one digital remote. The machine
with the remote plugged into it becomes the Master. The other machines are
Slaves. The machines are interconnected with DMX cabling.
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to select  or .
Press the Enter button to store the link setting.
The machine should be set to  only if it is running as a master. If running
as a slave, stand-alone or DMX controlled it should be set to .
Aux option
This option is not currently used and has no effect on the machine.
Priming the machine
If the machine runs out of fluid or you are priming a new machine, use the
PRIME function:
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to change the option to .
Press the Enter button to start the priming function.
The machine will pump until it detects fluid entering the block
To exit this menu if you decide not to activate the Prime function, select  and
press Enter.
If the machine is not up to operating temperature the Prime function will do
nothing.
Control settings
13
Resetting options to factory settings
The factory settings configure a standard mode of operation for the machine.
Use the Previous / Next buttons to select the  option.
Use the Up/Down buttons to change the option to .
Press the Enter button to reset all options.
To exit this menu if you decide not to reset the options, select  and press
Enter.
The factory settings are:
14
option
setting
HAZE

FAN

TRUN

TOFF

RUN

LINK

Control settings
Remote control
Overview
The JEM K1™ Digital Remote control, available separately, may be used for
remote control of the JEM K1 Hazer™. Several machines may be controlled from
one remote using the LINK function (see page 13).
Display
XLR socket
XLR socket
(on rear)
Timer button
Haze button
Functions
The remote control provides the following functions:
•
Haze button: turns haze output on and off. Press once to start haze and
again to stop.
•
Timer button: turns the haze timer on and off.
•
Haze level setting (HAZE = 0 -100%)
•
Fan speed setting (FAN = 0 -100%)
•
Timer run time/off time settings (,  = 0 - 90 seconds)
•
Run mode (RUN = , , , , )
The functions are the same as on the built in control panel and are described on
page 11.
The Haze button works by setting RUN to  (or ). The Timer
button sets RUN to  or . These buttons are simply a quick way to
control this menu function.
Remote control
15
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512 standard may be used to control
and program the haze output of the JEM K1 Hazer™.
When a DMX signal is present, the JEM K1 Hazer™ stand-alone
functions do not work. To fire the unit from the control panel or remote
control, the DMX controller must be powered off or disconnected.
Connection
The JEM K1 Hazer™ provides both 3-pin and 5-pin XLR sockets on the rear
panel of the machine for DMX connection. The sockets are interconnected: a
DMX line connected to the 3-pin IN socket may be continued through the 5-pin
OUT socket and vice versa. Do not, however, attempt to split a DMX line by
using both the 3-pin and 5-pin OUT sockets.
For best results, use cable designed for high speed digital data transmission.
Suitable DMX cable is available from your Martin dealer.
DMX functions
The JEM K1 Hazer™ address setting must match the DMX address allocated to
it on the controller. To set the address, see “Setting the DMX base address” on
page 13. The JEM K1 Hazer™ requires two DMX channels.
DMX channel 1
Function: Haze Density
0-19
Standby
20-219
Proportional output level control
220-255
Prime
DMX channel 2
Function: Fan Speed
0-219
0-100%, heaters on
220-244
Auto fan mode
245-255
Machine shutdown, heaters off
For example if the JEM K1 Hazer™ is set to DMX address 100, channel 1 will be
controlled by address 100 and channel 2 will be controlled by address 101.
When the machine is at running temperature and is under DMX control it
displays .
16
DMX control
Fog fluid types
The following type of Martin fog fluid is suitable for use in this machine. Martin
supplies high quality fog fluids that are based on ultra-pure deionised water.
Use only the following genuine Martin fog fluid. No other fluid is suitable for use.
DANGER! The JEM K1 Hazer™ can run safely only on the specific haze fluid it is
designed for. Use ONLY the Martin haze fluid designated in this manual. NEVER
use any other type of fluid, or toxic gas may be produced. You will probably also
cause damage to the system that is not covered by the product warranty. Do not
dilute haze fluid with water or any other liquid. Discard haze fluid if it becomes
contaminated.
JEM K1™ Haze Fluid
JEM K1™ fluid is a light molecular fluid which generates an invisible canvas,
specially designed to project light beams and lasers. The haze is slow
dispersing with an extended, long hang time.
Fog fluid types
17
Basic service
Before servicing the JEM K1 Hazer™, read and observe all the precautions listed
in “Safety information” on page 3. Any service not described in this section must
be carried out by a Martin service technician.
Cleaning
Excessive dust, haze fluid, and dirt build-up will degrade performance and
cause overheating and damage to the machine that is not covered by the
product warranty. To maintain adequate cooling, dust must be cleaned from the
outer casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The haze output nozzle remains hot for up to 10 hours after use.
•
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•
Clean haze fluid residues from the output of the machine.
•
Clean the outer casing with a damp cloth only.
Error messages
If the display shows , the machine has detected an internal fault. Switch off
the machine and contact Martin Service.
Fuse replacement
The main fuse for the JEM K1 Hazer™ is in a fuse holder located adjacent to the
power inlet. To replace the fuse, disconnect the power cord from the supply,
unscrew the cap of the fuse holder and pull out the fuse. Remove the spent fuse
and replace with one of exactly the same size and rating. The fuse type is
indicated on the serial number label as well as below. Contact Martin Service if
the fuse blows repeatedly.
18
Basic service
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait 5 to 7 minutes
 set to 0
Increase setting
 set to 0
Increase setting
DMX signal present
Disconnect or turn off DMX
controller
Machine can be fired from
control panel or remote
control, but not by DMX
controller
DMX address setting
incorrect
Change DMX address (page
13)
Poor connection in DMX line
Check DMX cables and
connections
Haze output is weak
Machine requires priming
Prime machine (page 13)
Wet, greasy, non-uniform
haze output, fluid drips or
spits from nozzle, or very
loud noise when firing
machine
Incompatible haze fluid
Use approved fluid!
Mains fuse blown
Replace fuse (page 18)
No power at AC cable inlet
Check power cable and
circuit breaker
Machine will not produce
haze when control panel or
remote control HAZE switch
turned on
Machine appears dead
Troubleshooting
19
Status messages
message


reason
The heaters are Off, the unit is shut down.
The unit is heating up to operating temperature.
The heater is at operating temperature, but Haze is not turned

on.
The heater is at operating temperature and the unit is under

DMX control.
(Number may be 01 to 90): Machine is in timer mode,

counting down the run period.
(Number may be 01 to 90): Machine is in timer mode,

counting down the off period.
(Number may be 90 to 00): The machine is carrying out its

shutdown sequence.
The machine has detected an error with its calibration

settings and will not operate. Call Martin Service.
The air pump is not working. This indicates a fault. Turn the

machine off and call Martin Service.
The fluid pump is not working. This indicates a fault. Turn the

machine off and call Martin Service.
The heater is at too high a temperature. This indicates a fault.

Turn the machine off and call Martin Service.
(on start-up) The machine’s run time has passed its
recommended service interval. The machine is safe to use

but should be serviced as soon as is convenient.
(on start-up) The internal battery is low and the last shutdown
did not complete. If this message displays on every start-up,

call Martin Service to obtain a replacement battery.
20
Status messages
Specifications
P h ys i c a l
Length .........................................................................................................544mm
Width ........................................................................................................... 459mm
Height..........................................................................................................344mm
Dry weight ....................................................................................................21.5Kg
Performance
Effect coverage ....................................................................................5000m3/min
Operating time ...................................................................................... continuous
Warm up time ......................................................................................... 5 minutes
Safety device.........................................................................................DTP device
Control and programming
Control options ...................................................................... DMX, digital remote
DMX channels ...................................................................................................... 2
F l u i d s ys t e m
Capacity ...................................................................................................... 2.5 litre
Fluid consumption (max) .........................................................................140ml/hr
Compatible fluids ...................................................................................... K1 Haze
Connections
DMX.................................................................................................. 3 or 5 pin XLR
Remote / machine link .............................................................................3 pin XLR
AC power .............................................................................................. PowerCon
Electrical
AC voltage ........................................................................... 120V / 230V, 50/60Hz
Main fuse (120V US version) ..........................................................................10AT
Main fuse (230V EU version) ............................................................................5AT
Power usage (120V US version) ........................................................ 675W (6.0A)
Power usage (230V EU version) ........................................................ 675W (3.1A)
Thermal
Maximum ambient temperature (Ta max)............................................ 40°C (104°F)
Exterior surface temperature, steady state, at 20°C ambient .............. 40°C (104°F)
Approvals
European EMC:......................................................... EN 61000-6-3:2001 – Part 6-3
European safety: ......................................................................... EN 60 335-1:2002
Immunity: ................................................................... EN 61000-6-1:2001 – Part6-1
ETL approval (cETLus) ..................... UL Std.998, CAN/CSA Std. C22.2 No 104-01
Specifications
21
Included items:
EU Model:
2.5m (6.56ft) power cable 3x1.0mm² with PowerCoN™ male connector
US Model:
2m (6.5ft) US power cable 18AWG with Nema 5-15 plug to PowerCoN™ male
connector (UL approved)
1 x 2.5L fluid container (empty)
Ordering information
Martin JEM K1 Hazer™ 120V ....................................................................92225900
Martin JEM K1 Hazer™ 230V ....................................................................92225901
JEM K1™ digital remote control................................................................92765036
Flying Kit for Martin JEM K1 Hazer™ ........................................................92610002
Flightcase for Martin JEM K1 Hazer™.......................................................91540012
22
Specifications
Notes
Notes
23
Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N
Phone: +45 87 40 00 00 Internet: www.martin.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement