Axiomtek SBC84620 3.5-inch Embedded Board User Manual

SBC84620 Series

AMD

®

Geode GX3 All-In-One

Capa Board

User’s Manua

l

Disclaimers

This manual has been carefully checked and believed to contain accurate information. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use.

AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.

AXIOMTEK reserves the right to change or revise this document and/or product at any time without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AXIOMTEK Co., Ltd.

CAUTION

If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturer’s instructions to only replace the same or equivalent type of battery, and dispose of used ones.

©

Copyright 2009 AXIOMTEK Co., Ltd.

All Rights Reserved

February 2009, Version A4

Printed in Taiwan

ii

ESD Precautions

Computer boards have integrated circuits sensitive to static electricity.

To prevent chipsets from electrostatic discharge damage, please take care of the following jobs with precautions: z z z

Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them.

Before holding the board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds.

It discharges static electricity from your body.

Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components.

Trademarks Acknowledgments

AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.

Windows

®

is a trademark of Microsoft Corporation.

Phoenix & AWARD are trademarks of Phoenix Technology Ltd.

IBM, PC/AT, PS/2, VGA are trademarks of International Business

Machines Corporation.

LX800 and CS5536 are registered trademarks of AMD Corporation.

Winbond is a trademark of Winbond Electronics Corp.

Other brand names and trademarks are the properties and registered brands of their respective owners. iii

Table of Contents

Disclaimers ........................................................................................................... ii

ESD Precautions ................................................................................................. iii

Chapter 1 Introduction .................................................................... 1

1.1 Specifications .......................................................................................... 2

Chapter 2 Jumpers and Connectors ............................................. 5

2.1 Board Dimensions and Fixing Holes ....................................................... 5

2.3.1 Audio Output Select Jumper (JP1)................................................. 10

2.3.2 LCD Voltage Select Jumper (JP2) ................................................. 10

2.3.3 CMOS Clear Jumper (JP3) ............................................................ 11

2.3.4 CompactFlash Power Jumper (JP4) .............................................. 11

2.3.5 COM1 Mode Select Jumpers for RS-232/422/485......................... 12

2.3.6

2.3.7

COM1 Mode Select Jumper (JP6) ................................................. 13

COM2 Mode Select Jumper (JP8) ................................................. 14

2.3.8 Compact Flash Setting Jumper (JP9) ............................................ 15

2.3.9 COM4 Mode Select Jumper (JP11) ............................................... 15

2.3.10 COM3 Mode Select Jumper (JP12) ............................................... 16

2.4 Connectors ............................................................................................ 17

2.4.1 Enhanced IDE Interface Connector (CN1_IDE) ............................. 18

2.4.2 LCD Connector (CN2_LCD)........................................................... 19

2.4.3 -5V Power Connector (CN3) .......................................................... 21

2.4.4 Audio Connector (CN4) .................................................................. 21

2.4.5 Digital I/O Port (DIO) Connector (CN5) .......................................... 22

2.4.6 SM BUS Connector (CN6) ............................................................. 22

2.4.7 Mini PCI Connector (CN7)............................................................. 23

2.4.8

2.4.9

ATX Power Connector (CN8) ........................................................ 24

Parallel Port Connector (CN9)...................................................... 25

2.4.10 Ethernet PJ-45 Connectors (LAN1, LAN2)..................................... 26

2.4.11 PC/104 Connectors (ISA1)............................................................. 27

2.4.12 Serial Port Interface Connectors (CN10, CN12, CN13) ................. 28

2.4.13 Flat Panel Bezel Connector (CN11) .............................................. 30

2.4.14 Keyboard and PS/2 Mouse Connector (CN14) ............................. 31

2.4.15 VGA Connector (CN15)................................................................. 31

2.4.16 CompactFlash

TM

Connector (CN17)............................................... 32

2.4.17 USB Connectors (USB1, USB2) .................................................... 33

Chapter 3 Hardware Description.................................................. 35

3.1 Microprocessors .................................................................................... 35

3.2 BIOS...................................................................................................... 35

3.4 I/O Port Address Map ............................................................................ 36 iv

Chapter 4 Award BIOS Utility ....................................................... 39

4.1 Entering Setup.............................................................................. 39

4.4

4.5

4.6

4.7

The Main Menu ..................................................................................... 41

Standard CMOS Setup Menu................................................................ 42

Advanced BIOS Features...................................................................... 44

Advanced Chipset Features .................................................................. 47

4.9

4.10

4.11

4.12

4.13

4.14

4.15

4.16

Power Management Setup .................................................................... 53

PnP/PCI Configuration Setup................................................................ 55

PC Health Status................................................................................... 57

Load Fail-Safe Default........................................................................... 58

Load Optimized Defaults ....................................................................... 59

Set Supervisor/User Password ............................................................. 60

Save & Exit Setup ................................................................................. 61

Exit Without Saving ............................................................................... 62

Appendix A Watchdog Timer ....................................................... 63

Appendix B Installation of Drivers............................................... 65

Appendix C Digital I/O ................................................................... 81 v

MEMO

vi

SBC84620 AMD

®

Geode GX3 All-in-One Capa Board User’s Manual

C h a p t e r 1

Introduction

The SBC84620 is a Capa board with support for AMD

®

LX800 CPU at FSB 500 MHz (optional LX700 433 MHz) that features graphics,

Fast Ethernet and an audio interface. The board can be adapted to

AMD

®

processors with its designing for space-limited applications, and a standard format conforming to the size of a 3.5” Hard Disk drive.

To simplify the system integration, super I/Os, LCD, Ethernet and solid state disk are provided to make all on one single borad. Four serial ports (3 x RS-232, 1 x RS-232/422/485) with +5V/12V power capability make a unique embedded feature to apply an extensive array of PC peripherals. The industrial-grade construction of

SBC84620 Series allows your system to endure the continuous operation in hostile environments where most require stability and reliability. The system dependability of SBC84620 Series can be enhanced by its built-in watchdog timer, a special industrial feature not commonly seen on other motherboards.

Introduction

1

SBC84620 AMD

®


1.1 Specifications

z

CPU

AMD

®

LX800 (GX3) and optional LX700 processors

z

System Chipset

CS5536AD

z

CPU Frequency

LX800 500 MHz (optional LX700 433 MHz) z

BIOS:

Phoenix-Award BIOS, Y2K compliant

4Mbit Flash, DMI, Plug and Play

PXE Ethernet Boot ROM

“Load Optimized Default” to backup customized Setting in the BIOS flash chip to prevent from CMOS battery fail z

System Memory:

One 200-Pin DDR SODIMM socket

Maximum DDR of up to 1GB DDR333 z

Onboard IDE:

One PATA-100 with 44-pin 2.0 pitch box-header

PATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra

DMA/33/66/100 z

Compact Flash Socket:

One Compact Flash Type II Socket z

Onboard Multi I/O:

Three RS-232 and one RS-232/422/485

PC/104 z

NOTE The PCI/104 slot supports I/O mode module only.

USB Interface

Four USB ports with fuse protection and comply with USB

Sepc. Rev. 2.0

2

Introduction

z

SBC84620 AMD

®


Real Time Clock

Integrated CS5536AD z

Watchdog Timer:

1~255 seconds; up to 255 levels z

Graphics/Streaming:

Integrate LX800

Unified Memory Architecture shares system memory up to

254MB

LCD Interface -- Supports up to 24-bit TFT LCD (TTL signal)

CRT: 1600 x 1200 x 32 bpp

LCD: 1600 x 1200 x 32 bpp z

Ethernet:

Realtek RTL8139DL PCI Bus 10/100M Base-T

Wake On LAN (via ATX power supply)

Equipped with RJ-45 interface z

Audio:

Realtek ALC202A AC’97 codec audio

Amplify for speaker-out with 1W for each channel

MIC-in, Line-in, Line-out/Speaker-out (jumper selectable) z

Power Management

ACPI (Advanced Configuration and Power Interface) / APM z

Form Factor: 3.5” hard disk drive form factor

NOTE All specifications and images are subject to change without notice.

Introduction

3

SBC84620 AMD

®


z z z z z

Chipset Driver

VGA Driver

PCI Bridge Driver

LAN Driver

Audio Driver

4

Introduction

SBC84620 AMD

®


C h a p t e r 2

Jumpers and Connectors

2.1 Board Dimensions and Fixing Holes

Jumpers and Connectors

Component Side

5

SBC84620 AMD

®


6

Solder Side


SBC84620 AMD

®


CN4 CN3 CN1_IDE

CN2_LCD

JP1

CN5

CN6

BAT1

CN7

ISA1

JP4

CN9

CN10

CN12

JP5

USB1

JP6

JP8

JP11

JP12

JP7 JP10

CN13

JP9

USB2 LAN1 CN14 LAN2

Component Side

Note The Limited Height of Component Side is 30mm.

CN15

JP2

JP3

CN8

CN11


7

SBC84620 AMD

®


Solder Side

8 Jumpers and Connectors

SBC84620 AMD

®


The SBC84620 Series is configured to match the needs of your application with the proper jumper settings. The table below is a summary of all the jumpers and their corresponding functions onboard the SBC84620 Series. The succeeding tables show the correct jumper settings for the onboard devices.

Jumper Default Setting Jumper Setting

JP1

Audio Line Out/Speaker Out: Line

Short 1-3, 2-4

Out

JP2 LCD Voltage select : 3.3V Short 1-2

Short 1-2 JP3 Clear CMOS Setting : Normal

JP4

Compact Flash Power Select :

3.3V

Short 1-2

JP5 COM1 Mode Select: RS-232

JP6

COM1 Mode

Select

CN13 Pin 1:

DCD

Short 3-5,4-6

Short 3-5

CN13 Pin 9: RI Short 4-6


JP8

COM2 Mode

Select

CN10 Pin 1:

DCD

Short 3-5,4-6

Short 3-5


JP9 Compact Flash Select : Slave Short 1-2


JP11

COM4 Mode

Select

CN10 Pin 11:

DCD

JP12

COM3 Mode

Select

Short 1-2

Short 3-5


CN12 Pin 1:

DCD

Short 3-5



9

SBC84620 AMD

®


2.3.1 Audio Output Select Jumper (JP1)

Description

Audio Output

Selection

Function

Line Out

(Default)

Jumper Setting

JP1

Speak Out

JP1

2.3.2 LCD Voltage Select Jumper (JP2)

Description

LCD Voltage

Select

Function

3.3V (Default)

Jumper Setting

JP2

5V

JP2


SBC84620 AMD

®


2.3.3 CMOS Clear Jumper (JP3)

Description

CMOS Clear

Function

Normal (Default)

Jumper Setting

JP3

Clear CMOS

JP3

2.3.4 CompactFlash Power Jumper (JP4)

Description

CompactFlash

Power Select

Function

3.3V (Default)

Jumper Setting

JP4

5V

JP4


11

SBC84620 AMD

®


2.3.5 COM1 Mode Select Jumpers for RS-232/422/485

(JP5, JP7, JP10)

Description Function

COM1 RS-232

(Default)

JP10

Jumper Setting

JP5 JP7

RS-422

JP10

JP5

JP7

RS-485

JP10 JP5 JP7


SBC84620 AMD

®


2.3.6 COM1 Mode Select Jumper (JP6)

Description Function Jumper Setting

COM1 (JP6) *Pin 1=DCD

(Default)

JP6

*Pin 1=5V

JP6

*Pin 9=RI

JP6

*Pin 9=+12V

JP6


13

SBC84620 AMD

®



Description Function Jumper Setting

COM2 (JP8) *Pin 1=DCD

(Default)

JP8

*Pin 1=5V

JP8

*Pin 9=RI

JP8

*Pin 9=+12V

JP8


SBC84620 AMD

®


2.3.8 Compact Flash Setting Jumper (JP9)

Description

Compact Flash

Master/Slave

Selection

Function

Master

Jumper Setting

JP9

Slave (Default)

JP9


Description

COM4 (JP11)

Function

*Pin 1=DCD

(Default)

Jumper Setting

JP11

*Pin 1=5V

JP11

*Pin 9=RI

JP11

*Pin 9=+12V

JP11


15

SBC84620 AMD

®



Description

COM3 (JP12)

Function

*Pin 1=DCD

(Default)

Jumper Setting

JP12

*Pin 1=5V

JP12

*Pin 9=RI

JP12

*Pin 9=+12V

JP12


SBC84620 AMD

®


2.4 Connectors

The connectors allow the CPU card to connect with other parts of the system. Some problems encountered by your system may be a result from loose or improper connections. Ensure that all connectors are in place and firmly attached. The following table lists the function of each connector on the SBC84620 Series.

Connectors

LCD Connector

Label Connectors

Parallel IDE Connector CN1_IDE Serial Port2 Connector

Serial Port4 Connector

Label

CN10

CN2_LCD Front Panel Bezel Connector CN11

-5V Power Connector CN3

Audio Connector CN4

Digital I/O Connector CN5



6-PinMiniDim Keyboard/Mouse

Connector

CN12

CN13

CN14

SMBUS Connector

MINIPCI Connector

CN6

CN7

ATX Power Connector CN8

Printer Port Connector CN9

LAN1 Connector LAN1

LAN2 Connector

PC104 Slot

LAN2

ISA1

VGA Connector

Compact Flash Connector

CN15

CN17

USB Port0 & Port1 Connector USB2

USB Port2 & Port3 Connector USB1

DDR SO-DIMM DIMM1


17

SBC84620 AMD

®


2.4.1 Enhanced IDE Interface Connector (CN1_IDE)

There is a PCI bus enhanced IDE controller that supports master/slave mode, post write transaction mechanisms with 64-byte buffer and master data transaction.

Pin Signal Pin Signal Pin Signal

1 Reset # 2 GND 3 Data 7

7 Data 5

10 Data 11

13 Data 2

16 Data 14

8

11

14

17

Data 10

Data 3

Data 13

Data 0

9

12

15

18

Data 4

Data 12

Data 1

Data 15

19 GND 20 No connector 21 No connector

22 GND 23 IOW 24 GND

25 IOR # 26 GND 27 IOCHRDY

28 No connector 29 No connector 30 GND-Default

31 Interrupt 32 No 33 SA1

34 No connector 35 SA0

37 HDC CS0 # 38 HDC CSI #

36 SA2

39 HDD Active #

40 GND 41 VCC 42 VCC

43 GND 44 N.C

CN1_IDE


SBC84620 AMD

®


2.4.2 LCD Connector (CN2_LCD)

The LCD connector on the board supports 24bit TTL flat panel displays.

Pin Signal

3 GND

5 VDDM

7 FPDISP

9 B0 (P0)

Pin Signal

2 +12VM

4 GND

6 VDDM

8 GND

10 B1(P1)

15 B6 (P6)

17 G0 (P8)

16 B7 (P7)

18 G1 (P9)

23 G6 (P14)

25 R0 (P16)

27 R2 (P18)

29 R4 (P20)

31 R6 (P22)

33 GND

35 FPCLK

37 M(DE)

39 GND

41 GND

43 VDDM

CN2_LCD

24 G7 (P15)

26 R1 (P17)

28 R3 (P19)

30 R5 (P21)

32 R7 (P23)

34 GND

40 FPENABKL

44 VDDM


19

SBC84620 AMD

®


Note

* If using the 18-bit LCD panel, please refer to this table below:

(B6,B7,G6,G7,R6,R7 is LSB)


SBC84620 AMD

®


2.4.3 -5V Power Connector (CN3)

The SBC84620 Series has a -5V Power Connector for PC104 expansion slot.

Pin Signal

1 -5V

2 GND

2

CN3

1 r

2.4.4 Audio Connector (CN4)

The SBC84620 supports an audio interface. CN4 is a 10-pin header connector commonly for the audio function.

Pin Signal Pin Signal

1 MIC-IN 2 GND

CN4

3 Line

5 Line

7

L

R

Audio Out L

4 GND

6 GND

8 GND

9 Audio Out R 10 GND


21

SBC84620 AMD

®


2.4.5 Digital I/O Port (DIO) Connector (CN5)

The board is equipped an 8-channel digital I/O connector CN5 that meets requirements for a system customary automation control. The digital I/O can be configured to control cash drawers and sense warning signals from an Uninterrupted Power System (UPS), or perform store security control. The digital I/O is controlled via software programming.


1 DO0 2 DI0

3 DO1 4 DI1

5 DO2 6 DI2

7 DO3 8 DI3

9 DO4 10 DI4

11 DO5 12 DI5

13 DO6 14 DI6

15 DO7 16 DI7

17 GND 18 GND

19 N.C. 20 N.C.

CN5

2.4.6 SM BUS Connector (CN6)

Connector CN6 is for SMBUS interface support.

Pin Signal

1 CLOCK

2 DATA

3 GND

CN6


SBC84620 AMD

®


2.4.7 Mini PCI Connector (CN7)


1 TIP

KEY

3 LAN_RD+

2 RING

KEY

4 LAN_TD+

5 LAN_RD-

7 RJ45 termination

6 LAN_TD-

8 RJ45 termination

9 RJ45 termination 10 RJ45 termination

11 LAN_LED1+ 12 LAN_LED2+

13 LAN_LED1- 14 LAN_LED2-

15 CHGND

17 INTB#

19 3.3V

21 RESERVED

23 GND

25 CLK

16 RESERVED

18 5V

20 INTA#

22 RESERVED

24 3.3VAUX

26 RST#

27 GND

29 REQ#

31 3.3V

33 AD31

35 AD29

37 GND

39 AD27

41 AD25

43 RESERVED

45 C/BE3#

47 AD23

49 GND

51 AD21

53 AD19

55 GND

57 AD17

59 C/BE2#

61 IRDY#

63 3.3V

65 CLKRUN#

28 3.3V

30 GNT#

32 GND

34 PME#

36 RESERVED

38 AD30

40 3.3V

42 AD28

44 AD26

46 AD24

48 IDSEL

50 GND

52 AD22

54 AD20

56 PAR

58 AD18

60 AD16

62 GND

64 FRAME#

66 TRDY#


23

SBC84620 AMD

®


Pin Signal

67 SERR#

69 GND

71 PERR#

73 C/BE1#

75 AD14

77 GND

79 AD12

81 AD10

83 GND

85 AD08

87 AD07

89 3.3V

91 AD05

93 RESERVED

95 5V

97 5V

99 AD01

101 GND

103 RESERVED

105 RESERVED

107 RESERVED

109 RESERVED

111 RESERVED

113 RESERVED

115 RESERVED

117 RESERVED

119 RESERVED

121 RESERVED

123 RESERVED

Pin Signal

68 STOP#

70 3.3V

72 DEVSEL#

74 GND

76 AD15

78 AD13

80 AD11

82 GND

84 AD09

86 C/BE0#

88 3.3V

90 AD06

92 AD04

94 AD02

96 AD00

98 RESERVED

102 GND

104 RESERVED

106 RESERVED

108 RESERVED

110 RESERVED

112 RESERVED

114 GND

116 RESERVED

118 RESERVED

120 RESERVED

122 RESERVED

124 RESERVED

2.4.8 ATX Power Connector (CN8)

Steady and sufficient power can be supplied to all components on the board by connecting the power connector. Please make sure all components and devices are properly installed before connecting the power connector. Align the power connector with its proper location on the board, and connect it tightly.


SBC84620 AMD

®



1 PS_ON

3 GND

7 +5V

9 N.C.

2 GND

4 +12V*

6 +SB5V

8 +5V

10 GND

CN8

NOTE * +12V is only for LCD Invreter, PC/104 and COM Port pin 9.

2.4.9 Parallel Port Connector (CN9)

The SBC84620 has a multi-mode parallel port connector CN9 to support:

1. Standard mode:

IBM PC/XT, PC/AT and PS/2

™ compatible with bi-directional parallel port

2. Enhanced mode:

Enhance parallel port (EPP) compatible with EPP 1.7 and EPP 1.9

(IEEE 1284 compliant)

3. High speed mode:

Microsoft and Hewlett Packard extended capabilities port (ECP)

IEEE 1284 compliant


1 Strobe# 2 Auto Form Feed#

3 Data Error#

7 Data 2 8 Printer Select In#

9 Data GND

11 Data GND

13 Data GND

15 Data GND

17 Data GND

19 Acknowledge# 20 GND


25

SBC84620 AMD

®



21 Busy 22 GND

24 GND

NC

CN9

2.4.10 Ethernet PJ-45 Connectors (LAN1, LAN2)

The RJ-45 connector is for Ethernet. To connect the board to a 100/10

Base-T hub, just plug one end of the cable into LAN1/LAN2, and connect the other end (phone jack) to a 1000/100/10-Base-T hub.

Pin Signal

LAN1/LAN2

2 Tx-(Data transmission negative)

3 Rx+(Data reception positive)

1 2 3 4 5 6 7 8

6 Rx- (Data reception negative)

RJ-45


SBC84620 AMD

®


2.4.11 PC/104 Connectors (ISA1)

PC/104 Bus Pin Assignment Table

Pin Pin Name Pin Pin Name Pin Pin Name Pin Pin Name

1 IOCHCHK 2 GND 3 SD7 4 RESETDRV

5 SD6

9 SD4

13 SD2

17 SD0

21 AEN

6 +5V

10 -5V

14 -12V

18 +12V

7 SD5

11 SD3

15 SD1

22 SMEMW 23 SA19

8 IRQ9

12 DRQ2

16 ENDXFR

19 IOCHRDY 20 GND

24 SMEMR

25 SA18

29 SA16

33 SA14

37 SA12

41 SA10

45 SA8

49 SA6

53 SA4

57 SA2

61 SA0

26 IOW

30 DACK3

34 DACK1

38 REFRESH 39 SA11

42 IRQ7

46 IRQ5

50 IRQ3

54 TC

58 +5V

62 GND

27 SA17

31 SA15

35 SA13

43 SA9

47 SA7

51 SA5

55 SA3

59 SA1

63 GND

28 IOR

32 DRQ3

36 DRQ1

40 SYSCLK

44 IRQ6

48 IRQ4

52 DACK2

56 SALE

60 OSC

64 GND

PC/104 Bus Pin Assignment Table

Pin Pin Name Pin Pin Name Pin Pin Name Pin Pin Name

1 GND 2 GND

5 IOCS16 6 LA23

9 IRQ11 10 LA21

13 IRQ15 14 LA19

17 DACK0

21 DACK5

25 DACK6

18 LA17

22 MEMW

26 SD9

29 DACK7

33 +5V

37 GND

30 SD11

34 SD13

38 SD15

3 MEMCS16 4 SBHE

7 IRQ10

11 IRQ12

15 IRQ14

19 DRQ0

23 DRQ5

27 DRQ6

8 LA22

12 LA20

16 LA18

20 MEMR

24 SD8

28 SD10

31 DRQ7 32 SD12

35 MASTER 36 SD14

39 GND 40 (KEY)

* NOTE The PCI/104 slot supports I/O mode module only.


27

SBC84620 AMD

®


2.4.12 Serial Port Interface Connectors (CN10, CN12,

CN13)

The board has four onboard serial ports, COM2~COM4 (RS-232) and

COM1 (RS-232/422/485). They are jumper selectable with auto flow control features. All ports supply +5V power capability on DCD, and

+12V on RI (excluding 5V), depending on jumper setting.

2.4.12.1 COM1 Port Connector (CN13)

The COM 1 Port connector CN13 is a standard DB-9 connector.

Pin Signal

1 DCD, Data carrier detect

2 RXD, Receive data

3 TXD, Transmit data

4 DTR, Data terminal ready

CN13

6 DSR, Data set ready

7 RTS, Request to send

8 CTS, Clear to send

2.4.12.2 COM3 Port Connector (CN12)


1 Data Carrier Detect (DCD)

3 Receive Data (RXD)

2 Data Set Ready (DSR)

4 Request to Send (RTS)

5 Transmit Data (TXD) 6 Clear to Send (CTS)

7 Data Terminal Ready (DTR) 8 Ring Indicator (RI)

9 Ground (GND) 10 NC

CN12


SBC84620 AMD

®


2.4.12.3 COM2/COM4 Port Connector (CN10)


1 NDCD2 11 NDCD4

2 NDSR2 12 NDSR4

3 NRX2 13 NRX4

4 NRTS2 14 NRTS4

5 NTX2 15 NTX4

6 NCTS2 16 NCTS4

7 NDTR2 17 NDTR4

8 NRI2 18 NRI4

9 GND

10 N.C

19 GND

20 N.C

2

1

CN10

20

19

2.4.12.4 COM1 (CN13) RS-422/485 Pin Assignment Table

Pin #

RS-422

Signal Name

RS-485

1 TX- DATA-

2 TX+ DATA+

9 GND GND


29

SBC84620 AMD

®


2.4.13 Flat Panel Bezel Connector (CN11)

Power LED

This 3-pin connector denoted as Pin 1 and Pin 5 connects the system power LED indicator to such a switch on the case. Pin 1 is assigned as +, and Pin 5 as -. The Power LED lights up when the system is powered ON.

External Speaker and Internal Buzzer Connector

Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker unit or internal buzzer. While connecting the CPU card to an internal buzzer, please short pins 2-4; while connecting to an external speaker, you need to set pins 2-4 to Open and connect the speaker cable to pin 8 (+) and pin 2 (-).

ATX Power On/Off Button

This 2-pin connector denoted as Pin 9 and 10 connects the front panel’s ATX power button to the CPU card, which allows users to control ATX power supply to be power on/off.

System Reset Switch

Pin 11 and 12 can be connected to the case-mounted reset switch that reboots your computer instead of turning OFF the power switch.

It is a better way to reboot your system for a longer life of the system’s power supply.


SBC84620 AMD

®


HDD Activity LED

This connection is linked to hard drive activity LED on the control panel. LED flashes when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front panel HDD LED, Pin 13 assigned as -, and Pin 14 as +

2.4.14 Keyboard and PS/2 Mouse Connector (CN14)

The board supports a keyboard and Mouse interface. Connector CN14 is a DIN connector for PS/2 keyboard Connection VIA “Y” Cable.

Pin Signal

CN14

3 GND

4 VCC

2.4.15 VGA Connector (CN15)

The board has three connectors to support CRT VGA and flat panel displays, individually or simultaneously. CN15 is a slim type 15-pin D-

Sub connector commonly for the CRT VGA display. The VGA interface configuration is done via the software utility, and no jumper setting is required.

Pin Signal Pin Signal Pin Signal

7 AGND 8 AGND 9 N/A

10 GND 11 N/A 12

15

CN15


31

SBC84620 AMD

®


2.4.16 CompactFlash

TM

Connector (CN17)

The board is equipped with a CompactFlash disk type-II socket on the solder side that supports the IDE interface CompactFlash disk card with DMA mode supported. The socket is especially designed to avoid any incorrect installation of the CompactFlash disk card.

When installing or removing the CompactFlash disk card, please make sure that the system power is off.


1 GND

2 Data 3

3 Data 4

4 Data 5

5 Data 6

6 Data 7

7 CS0#

9 ATASEL

13 VCC

26 CD1-

27 Data 11

28 Data 12

29 Data 13

30 Data 14

31 Data 15

32 CS1#

33 VS1#

34 IORD#

35 IOWR#

36 WE#

37 INTR

38 VCC

39 CSEL#

40 VS2#

41 RESET#

42 IORDY#

43 DMAREQ

44 DMAACK-

45 DASP#

46 PDIAG#


SBC84620 AMD

®



22 Data 1

23 Data 2

24 IOCS16#

25 CD2#

CN17

47 Data 8

48 Data 9

50 GND

2.4.17 USB Connectors (USB1, USB2)

The board supports four Universal Serial Bus (USB) connectors compliant with USB 2.0 (480 Mbps) that can be adapted to any USB peripherals, such as monitor, keyboard, and mouse.

2.4.17.1 USB Port Connector (USB2)

The Universal Serial Bus (USB) port connector on the board is for the installation of peripherals supporting the USB interface. USB2 consists of two 4-pin standard USB ports.

USB0 and USB1

Pin Signal

USB2

1, 5

2, 6

3, 7

USB Vcc

USB -

USB +

4, 8 USB GND


33

SBC84620 AMD

®


2.4.17.2 USB Connector (USB1)

The Universal Serial Bus (USB) connector on the board is for the installation of peripherals supporting the USB interface. USB1 is a 10pin standard onboard USB connector.

USB2 and USB3


1 VCC

3 D0-

5 D0+

2 VCC

4 D1-

6 D1+

USB1

9 Ground (GND) 10 Ground (GND)


SBC84620 AMD

®


C h a p t e r 3

Hardware Description

3.1 Microprocessors

The SBC84620 Series supports LX700/LX800.Systems based on these CPUs can be operated under Windows XP and Linux environments. The system performance depends on the microprocessor installed onboard. Make sure all settings are correct for the installed microprocessor to prevent any damage to the CPU.

3.2 BIOS

System BIOS used on the SBC84620 Series is Phoenix-Award Plug and Play BIOS. The SBC84620 Series contains a single 4Mbit Flash.

The SBC84620 Series industrial CPU card supports one 200-pin DDR

SODIMM socket for a maximum memory of 1GB DDR SDRAMs. The memory module can come in sizes of 64MB, 128MB, 256MB, 512MB and 1GB.

Hardware Description

35

SBC84620 AMD

®


3.4 I/O Port Address Map

It has a total of 1KB port addresses available for assignment to other devices via I/O expansion cards.

Address Devices

274-277

279-279

2E8-2EF

2F8-2FF

ISAPNP Read Data Port

ISAPNP Read Data Port

Serial port #4 (COM4)


3B0-3BA MDA video card (including LPT1)

3E8-3EF

3F0-3F5

3F6-3F6

3F7-3F7

3F8-3FF


Standard floppy disk controller

Primary IDE Channel

Standard floppy disk controller


36 Hardware Description

SBC84620 AMD

®


The SBC84620 Series is a 100% PC compatible control board. It consists of 16 interrupt request lines. Four out of the sixteen can either be programmable. The mapping list of the 16 interrupt request lines is shown on the following table.

IRQ Parity check error

IRQ0 System timer output

IRQ1 Keyboard

IRQ3

IRQ4

IRQ5

IRQ7

IRQ8

Serial port #2

Serial port #1

PCI Device Share

Parallel port #1

Real time clock

IRQ10

IRQ11

Serial port #3

Serial port #4

IRQ13 Math coprocessor

IRQ14 Primary IDE channel

IRQ15 —

Hardware Description

37

SBC84620 AMD

®


MEMO

38 Hardware Description

SBC84620 AMD

®


C h a p t e r 4

Award BIOS Utility

The Phoenix-Award BIOS has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in a battery-backed RAM (CMOS RAM) that retains the Setup information each time the power is turned off.

There are two ways to enter the Setup program. You may either turn

ON the computer and press <Del> immediately, or press the <Del> and/or <Ctrl>, <Alt>, and <Esc> keys simultaneously when the following message appears at the bottom of the screen during POST

(Power on Self Test).

TO ENTER SETUP PRESS DEL KEY

If the message disappears before you respond and you still want to enter Setup, please restart the system to try it again. Turning the system power OFF and ON, pressing the “RESET” button on the system case or simultaneously pressing <Ctrl>, <Alt>, and <Del> keys can restart the system. If you do not press keys at the right time and the system doesn’t boot, an error message will pop out to prompt you the following information:

PRESS <F1> TO CONTINUE, <CTRL-ALT-ESC> OR <DEL> TO ENTER SETUP

Award BIOS Utility

39

SBC84620 AMD

®


Up arrow

Down arrow

Left arrow

Right arrow

Esc key

PgUp/“+” key

PgDn/“

−“ key

F1 key

(Shift) F2 key

F3 key

F4 key

F5 key

F6 key

F7 key

F8 key

F9 key

F10 key

Moves cursor to the previous item

Moves cursor to the next item

Moves cursor to the item on the left hand

Move to the item in the right hand

Main Menu -- Quits and deletes changes into CMOS

Status Page Setup Menu and Option Page Setup

Menu -- Exits current page and returns to Main Menu

Increases the numeric value or makes changes

Decreases the numeric value or makes changes

General help, only for Status Page Setup Menu and

Option Page Setup Menu

Change color from total 16 colors. F2 to select color forward, (Shift) F2 to select color backward

Reserved

Reserved

Restores the previous CMOS value from CMOS, only for Option Page Setup Menu

Loads the default CMOS value from BIOS default table, only for Option Page Setup Menu

Loads the Setup default, only for Option Page Setup

Menu

Reserved

Reserved

Saves all the CMOS changes, only for Main Menu z z

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu/Option Page Setup Menu

Press <F1> to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <F1> or <Esc>.

40 Award BIOS Utility

SBC84620 AMD

®


Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from ten setup functions and two exit choices. Use the arrow keys to select the setup function you intend to configure then press <Enter> to accept or enter its sub-menu.

NOTE If you find that your computer cannot boot after making and saving system changes with Setup, the Award BIOS, via its built-in override feature, resets your system to the

CMOS default settings.

We strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both

Award and your system manufacturer to provide the absolute maximum performance and reliability.


41

SBC84620 AMD

®


4.5 Standard CMOS Setup Menu

The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the

<PgUp> or <PgDn> keys to select the value you want in each item. z

Date

The date format is <day>, <date> <month> <year>. Press <F3> to show the calendar.

day date

The day of week, from Sun to Sat, determined by the

BIOS, is read only

The date, from 1 to 31 (or the maximum allowed in the month), can key in the numerical / function key

month

The month, Jan through Dec.

year

The year, depends on the year of BIOS z

Time

The time format is <hour> <minute> <second> accepting either functions key or numerical key. The time is calculated based on the

24-hour military-time clock. For example, 1 p.m. is 13:00:00.


z

SBC84620 AMD

®


IDE Primary Master / Primary Slave

The categories identify the types of one channel that have been installed in the computer. There are 45 predefined types and 2 users definable types are for Enhanced IDE BIOS. Type 1 to Type

45 is predefined. Type User is user-definable.

Press <PgUp>/<+> or <PgDn>/<

−> to select a numbered hard disk type or type the number and press <Enter>. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information within this category. If your hard disk drive type does not match or is not listed, you can use Type User to define your own drive type manually.

If you select Type User, related information is asked to be entered to the following items. Enter the information directly from the keyboard and press <Enter>. This information should be provided in the documentation from your hard disk vendor or the system manufacturer.

If the controller of HDD interface is ESDI, select “Type 1”.

If the controller of HDD interface is SCSI, select “None”.

If the controller of HDD interface is CD-ROM, select “None”.

CYLS.

HEADS

number of cylinders LANDZONE landing zone number of heads

PRECOMP

write precom

SECTORS

MODE

number of sectors

HDD access mode z

If there is no hard disk drive installed, select NONE and press

<Enter>.

Halt On

This field determines whether the system will halt if an error is detected during power up.

No errors

All errors

All, But

Keyboard

All, But

Diskette

The system boot will halt on any error detected.

(default)

Whenever the BIOS detect a non-fatal error, the system will stop and you will be prompted.

The system boot will not stop for a keyboard error; it will stop for all other errors.

The system boot will not stop for a disk error; it will stop for all other errors.


43

SBC84620 AMD

®


All, But

Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all other errors.

Press <Esc> to return to the Main Menu page.

4.6 Advanced BIOS Features

This section allows you to configure and improve your system and allows you to set up some system features according to your preference. z

CPU Internal Cache

This option speed up memory access. However, it depends on the

CPU/chipset design. The default setting is “Enabled”. CPUs with no built-in internal cache will not provide the “CPU Internal Cache” item on the menu.

Enabled

Enable cache

Disabled

Disable cache


z

SBC84620 AMD

®


Quick Power On Self Test

This option speeds up Power on Self Test (POST) after you turn on the system power. If set as Enabled, BIOS will shorten or skip some check items during POST. The default setting is “Enabled”.

Enabled

Enable Quick POST

Disabled

Normal POST z

First/Second/Third Boot Device

These items allow the selection of the 1 st

, 2 nd

, and 3 rd

devices that the system will search for during its boot-up sequence. The wide range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM. z

Boot Other Device

This item allows the user to enable/disable the boot device not listed on the First/Second/Third boot devices option above. The default setting is “Enabled”. z

Boot Up NumLock Status

Selects power on state for NumLock. The default value is “On”. z

Gate A20 Option

The default value is “Fast”.

Normal

The A20 signal is controlled by keyboard controller or chipset hardware.

Fast

Default: Fast. The A20 signal is controlled by Port

92 or chipset specific method. z

Typematic Rate Setting

This determines the typematic rate of the keyboard. The default value is “Disabled”.

Enabled

Disabled

Enable typematic rate and typematic delay programming

Disable typematic rate and typematic delay programming. The system BIOS will use default value of these 2 items and the default is controlled by keyboard. z

Typematic Rate (Chars/Sec)

This option refers to the number of characters the keyboard can type per second. The default value is “6”.


45

SBC84620 AMD

®


6

8

10

12

15

20

24

30

6 characters per second







30 characters per second z

Typematic Delay (Msec)

This option sets the display time interval from the first to the second character when holding a key. The default value is “250”.

250

500

750

1000

250 msec

500 msec

750 msec

1000 msec z

Security Option

This item allows you to limit access to the system and Setup, or just to Setup. The default value is “Setup”.

System

Setup

The system will not boot and access to Setup will be denied if the incorrect password is entered at the prompt.

The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt.

NOTE To disable security, select PASSWORD SETTING

at Main Menu and then you will be asked to enter password. Do not type anything, just press

<Enter> and it will disable security. Once the security is disabled, the system will boot and you can enter Setup freely.

z

Small Logo (EPA) Show

If enabled, the EPA logo will appear during system booting up; if disabled, the EPA logo will not appear.



SBC84620 AMD

®


4.7 Advanced Chipset Features

Since the features in this section are related to the chipset on the CPU board and are completely optimized, you are not recommended to change the default settings in this setup table unless you are well oriented with the chipset features. z

CPU Frequency

Use this item to set the CPU Frequency with these options: Auto,

333MHz, 400MHz, 433MHz and 500MHz. The default setting is

“Auto”. z

CAS Latency

You can select CAS latency time in 1.5, 2.0, 2.5, 3.0, 3.5, or Auto.

The board designer should set the values in this field, depending on the DRAM installed. Do not change the values in this field unless you change specifications of the installed DRAM or the installed

CPU. z

Interleave Select

Select the address interleaving mode. The choice: HOI, LOI.

The GLMC(GeodeLink™ Memory Controller) module supports two address translations depending on the method used to interleave pages. High Order Interleaving (HOI) uses fixed upper address bits to map the GLIU address to a component bank. LOI uses variable lower address bits depending on page size, number of module banks, and number of component banks of the DIMMs, plus an


47

SBC84620 AMD

®


option to XOR with upper address bits.

The default setting is “LOI”. z

XOR BA0/ BA1/MB0

Enables XORing of component bank select BA0/BA1/MB0 with upper GLIU address bit. The default value is “Disabled”. z

XOR Bit Select

Select which upper GLIU address bit to XOR with MB0, BA1 or

BA0. Only applies to LOI mode. The choice: 18, 19, 20, 21. The default value is “18”. z

Video Memory Size

The options available are [8M] [16M] [32M] [64M] [128M] [254M]. z

Output Display

This allows you to choose output for your system display.

Configuration options: [CRT] [Flat Panel] [Panel +CRT]. The default value is “Panel +CRT”. z

Flat Panel Configuration

Press Enter to set the following items. z

Resolution

Select the resolution for LVDS panel. z

Data Bus Type

Select the Data Bus Type for LVDS panel. z

Refresh Rate

Select the refresh rate for LVDS panel. z

HSYNC Polarity

The choice: HI, LOW. z

VSYNC Polarity Active

The choice: HI, LOW. z

SHFCLK Active Period

Select the shift clock (SHFCLK) to be either free running, or active only during the display period. Some TFT panels recommend keeping the shift clock running during the retrace time. z

LP Active Period

Select the polarity of the LDE/MOD pin. This can be used for panels that require an active low timing LDE interface signal.


z

SBC84620 AMD

®


Overcurrent reporting

Select for USB controller. The options available are Enabled and

Disabled. z

Port 4 assigment

Select for USB Port.


This section allows you to configure your SuperIO Device, IDE

Function, Onboard Device, and ITE8888. z z

Onboard Serial Port 1/Port 2

Select an address and corresponding interrupt for the first and second serial ports.

Parallel Port Mode

Select an operating mode for the onboard parallel (printer) port.

Select Normal unless your hardware and software require one of the other modes offered in this field. The options available are

“EPP1.9”, “ECP”, “SPP”, “ECPEPP1.7” and “EPP1.7”.


49

SBC84620 AMD

®


z

ECP Mode Use DMA

Select a DMA channel for the parallel port for use during ECP mode. z

Onboard Serial Port 3/Port 4

Select an address for the third and fourth serial ports. The options available are “3F8”, “2E8”, “3E8”, “2F8” and “Disabled”. z

Serial Port 3/Port 4 Use IRQ

Select corresponding interrupt for the third and fourth serial ports.

The options available are “IRQ10” and “IRQ11”. z

IDE Primary Master/Slave PIO

The four IDE PIO (Programmed Input/Output) fields let you set a

PIO mode (0-4) for each of the four IDE devices that the onboard

IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The options available are “Auto“, “Mode 0“, “Mode 1“, “Mode 2“, “Mode 3“ and “Mode 4“. z

IDE Primary Master/Slave UDMA

Ultra DMA 66/100 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software support Ultra DMA

33/66/100, select Auto to enable BIOS support. The options available are “Auto“, “Mode 0“, “Mode 1“ and “Mode 2“. z

IDE HDD Block Mode

This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive. z

Onboard Audio

Select Enabled if your system contains a Audio controller and you want to use it. z

Onboard LAN Boot ROM

This item allows you to decide to boot from whether LAN1 or LAN2.

The options available are “LAN1“, “LAN2“ and “Disabled“.


z

SBC84620 AMD

®


ITE8888 Configuration

z

Positively Decode I/O

Press Enter to set ITE8888 decode I/O function. z

Positively Decode I/O 0/1/2/3/4/5 IO Space 0 Size

This item allows the user to enable/disablee the Positively Decode

I/O 0/1/2/3/4/5. The default setting is “Disabled”.


51

SBC84620 AMD

®


z

IO Space 0/1/2/3/4/5 Size

This item allows the user to decide the Size of I/O Space

0/1/2/3/4/5. The options available are “1, 2, 4, 8, 16, 32, 64 and

128”. z

IO Base Address 0/1/2/3/4/5

This item allows the user to decide the Base Address of Decode

I/O 0/1/2/3/4/5. The available value are 0000~FFFF. z

Positively Decode Memory

Press Enter to set ITE8888 Decode Memory function. z

Positively Decode Mem 0/1/2/3 IO Space 0 Size

This item allows the user to enable/disablee the Positively Decode

Mem 0/1/2/3. The default setting is “Disabled”. z

Mem Space 0/1/2/3 Size

This item allows the user to decide the Size of Memory Space

0/1/2/3. The options available are “16KB, 32 KB, 64 KB, 128 KB,

256 KB, 512 KB, 1MB and 2MB”. z

Mem Base Address 0/1/2/3

This item allows the user to decide the Base Address of Decode

Memory 0/1/2/3/4/5. The available value are 0000~FFFF.



SBC84620 AMD

®


4.9 Power Management Setup

The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity. z z

ACPI Function

This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The function is always Enabled.

Power Management

This option allows you to select the type of power Management.

The options available are APM, ACPI. z

Standby Mode

After the selected period of system inactivity (1 minute to 1 hour), the fixed disk drive and the video shut off while all other devices still operate at full speed. The default value is “Disabled”.

Disabled

1/2/4/6/8/10/20/30/4

0 Min/1 Hr

System will never enter STANDBY mode.

Defines the continuous idle time before the system entering STANDBY mode.

If any item defined in (J) is enabled & active,

STANDBY timer will be reloaded.


53

SBC84620 AMD

®


z

Suspend Mode

After the selected period of system inactivity (1 minute to 1 hour), all devices except the CPU shut off. The default value is “Disabled”.

Disabled

1/2/4/6/8/10/2

0/30/40

Min/1 Hr

System will never enter SUSPEND mode

Defines the continuous idle time before the system entering SUSPEND mode.

If any item defined in (J) is enabled & active,

SUSPEND timer will be reloaded z

Modem Use IRQ

3, 4, 5, 7, 9,

10, 11, NA

For external modem, 3 or 4 will be used for card type modem. It is up to card definition. Default is 3. z

Soft-Off by PWR-BTTN

This option only works with systems using an ATX power supply. It also allows the user to define which type of soft power OFF sequence the system will follow. The default value is “Instant-Off”.

Instant-Off

Delay 4 Sec.

This option follows the conventional manner systems perform when power is turned OFF. Instant-Off is a soft power OFF sequence requiring only the switching of the power supply button to OFF

Upon turning OFF system from the power switch, this option will delay the complete system power OFF sequence by approximately 4 seconds. Within this delay period, system will temporarily enter into Suspend Mode enabling you to restart the system at once. z

PWRON After PWR-Fail

This option allows you to select the type of power loss function.

The options available are On, Off. The default value is “Off”.



SBC84620 AMD

®


4.10 PnP/PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or

Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. z z z

PNP OS Installed

Select Yes if the system operating environment is Plug-and-Play aware (e.g., Windows 95). The default value is “No”.

Reset Configuration Data

Normally, you leave this item Disabled. Select Enabled to reset

Extended System Configuration Data (ESCD) when you exit Setup or if installing a new add-on cause the system reconfiguration a serious conflict that the operating system can not boot. Options are:

“Enabled, Disabled”.

Resources Controlled By

The Award Plug and Play BIOS can automatically configure all boot and Plug and Play-compatible devices. If you select Auto, all interrupt request (IRQ), DMA assignment, and Used DMA fields disappear, as the BIOS automatically assigns them. The default value is “Manual”.


55

SBC84620 AMD

®


z

IRQ Resources

When resources are controlled manually, assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt:

1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1).

2. PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.

The default value is “PCI/ISA PnP”. z

DMA Resources

When resources are controlled manually, assign each system DMA channel as one of the following types, depending on the type of device using the interrupt:

Legcy ISA Devices compliant with the original PC AT bus specification, requiring a specific DMA channel.

PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.

The default value is “PCI/ISA PnP”. z

Memory Resources

This sub menu can let you control the memory resource. z

PCI/VGA Palette Snoop

Some non-standard VGA display cards may not show colors properly. This item allows you to set whether MPEG ISA/VESA

VGA Cards can work with PCI/VGA or not. When enabled, a

PCI/VGA can work with a MPEG ISA/VESA VGA card; when disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.



SBC84620 AMD

®


4.11 PC Health Status

This section supports hardware monitering that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. z

Current CPU Temperature

These read-only fields reflect the functions of the hardware thermal sensor that monitors the chip blocks and system temperatures to ensure the system is stable.



57

SBC84620 AMD

®


4.12 Load Fail-Safe Default

When you press <Enter> on this item, a confirmation dialog box pops out to show you such a message:

Please press “Y” to load default values that will be factory settings for accomplishing the optimal performance of system operations.


SBC84620 AMD

®


4.13 Load Optimized Defaults

This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features.

To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter

“N”.


59

SBC84620 AMD

®


4.14 Set Supervisor/User Password

You can set either supervisor or user password, or both of then. The differences between are:

1.

2.

Supervisor password: can enter and change the options of the setup menus.

User password: just can enter but do not have the right to change the options of the setup menus.

When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

ENTER PASSWORD:

Type the password with eight characters at most, and press <Enter>.

The password typed will now clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.

To disable password, just press <Enter> when you are prompted to enter password. A message will confirm the password being disabled.

Once the password is disabled, the system will boot and you can enter

Setup freely.

PASSWORD DISABLED.

When a password is enabled, you have to type it every time you enter

Setup. This prevents any unauthorized person from changing your system configuration.

Additionally when a password is enabled, you can also require the

BIOS to request a password every time the system reboots. This would prevent unauthorized use of your computer.

You determine when the password is required within the BIOS

Features Setup Menu and its Security option. If the Security option is set to “System”, the password is required during boot up and entry into

Setup. If set as “Setup”, prompting will only occur prior to entering

Setup.


SBC84620 AMD

®


4.15 Save & Exit Setup

This allows you to determine whether or not to accept the modifications.

Typing “Y” quits the setup utility and saves all changes into the CMOS memory. Typing “N” brigs you back to Setup utility.


61

SBC84620 AMD

®


4.16 Exit Without Saving

Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility.


SBC84620 AMD

®


A p p e n d i x A

Watchdog Timer

Watchdog Timer Setting

The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.

Using the Watchdog Function

Start

↓

Un-Lock WDT:

↓

O 2E 87 ; Un-lock super I/O


Select Logic device:

O 2E 07

O 2F 08

↓

Activate WDT:

↓

Set Second or Minute :

↓

Set base timer :

O 2F 01

O 2F N N=00 or 08(See below table)

O 2F M=00,01,02,…FF(Hex) ,Value=0 to 255

↓

WDT counting re-set timer :

O 2F M ; M=00,01,02,…FF(See below table)

Watchdog Timer

63

SBC84620 AMD

®


; IF to disable WDT:

O 2F 00 ; Can be disable at any time

z

Timeout Value Range

1 to 255

Minute / Second z

Program Sample

Watchdog timer setup as system reset with 5 second of timeout

2E, 87

2E, 87

2E, 07

2F, 08

2E, 30

2F, 01

2E, F5

2F, N

2E, F6

2F, M

Logical Device 8

Activate

Set Minute or Second

N=08 (Min),00(Sec)

Set Value

M = 00 ~ FF

64 Watchdog Timer

1.

SBC84620 AMD

®


A p p e n d i x B

Installation of Drivers

Installation of AES Driver

1-1. Click the “Device Manager” button.

Installation of Drivers

65

SBC84620 AMD

®


1-2. Click the “Update Driver” option.

1-3. Click the “Next” button.

66 Installation of Drivers

SBC84620 AMD

®



1-5. Click the “Browse” button to select AES Driver Folder, and then click the “Next” button.


67

SBC84620 AMD

®


1-6. Click the “Finish” button.

1-7. The Geode LX AES Crypto Driver installation is finished.


2.

SBC84620 AMD

®


Installation of Audio Driver

2-1. Enter the “Device Manager” window, click right mouse button on the “Multimedia Audio Control” icon, and a pull-down list pops out. Please slect the “Update Driver” option.

2-2. Click the “Next” button


69

SBC84620 AMD

®



2-4. Click the “Browse” button to access the correct location of the Audio Driver folder, and then click the “Next” button.


SBC84620 AMD

®


2-5. Click the “Continue Anyway” button.



71

SBC84620 AMD

®


2-7. The Audio Driver installation is finished.


3.

SBC84620 AMD

®


Installation of LAN Driver

3-1. Click the “Setup” icon



73

SBC84620 AMD

®


3-3. Click the “Install” button.



SBC84620 AMD

®


4. Installation of PCI Bridge Driver

4-1. Enter the “Device Manager” window, click right mouse button on the “Other PCI Brige Device” icon, and a pulldown list pops out. Please select the “Update Driver” option.



75

SBC84620 AMD

®



4-4. Click the “Browse” button to access the correct location of PCI Bridge for ITE8888 driver.


SBC84620 AMD

®




77

SBC84620 AMD

®


5. Installation of VGA Driver

5-1. Enter the “Device Manager” window, click right mouse button on the “Video Controller” ican, and a pull-down list pops out. Please click the “Update Driver” option.



SBC84620 AMD

®



5-4. Click the “Browse” button to access the correct location of

VGA driver.


79

SBC84620 AMD

®


5-5. Click the “Continue Anyway” button.


*

Please reboot the syster after finishing all drivers’ installation.


SBC84620 AMD

®


A p p e n d i x C

Digital I/O

Using the Digital Input Function

Start

↓

Un-Lock SuperI /O:

↓



SelectMultiplexed pin to GPIO Function :

O 4E 2A

O 4F FF

↓


O 4E 07

O 4F 07

↓

Activate Logic Device:

↓

Select GPI Function:

O 4F 01

↓

Read Data:

O 4F FF

XX ( XX is input Data; if no input source,the value is FF)

Digital I/O

81

SBC84620 AMD

®


Using the Digital Output Function

Start

↓

Un-Lock SuperI /O:

↓



SelectMultiplexed pin to GPIO Function :

O 2E 2A

O 2F FF

↓


O 2E 07

O 2F 07

↓

Activate Logic Device:

O 2F 01

↓

Select GPO Function:

↓

Output Data:

O 2F 00

O 2F 00

O 2F XX=00,01,02,…FF(XX is Output Data)

82 Digital I/O

Axiomtek SBC84620 3.5-inch Embedded Board User Manual

Assistant Bot

®

l

Disclaimers

CAUTION

©

ESD Precautions

Trademarks Acknowledgments

1.1 Specifications

2.1 Board Dimensions and Fixing Holes

2.4 Connectors

3.1 Microprocessors

3.2 BIOS

3.4 I/O Port Address Map

4.5 Standard CMOS Setup Menu

4.6 Advanced BIOS Features

4.7 Advanced Chipset Features

4.9 Power Management Setup

4.10 PnP/PCI Configuration Setup

4.11 PC Health Status

4.12 Load Fail-Safe Default

4.13 Load Optimized Defaults

4.14 Set Supervisor/User Password

4.15 Save & Exit Setup

4.16 Exit Without Saving

Watchdog Timer Setting

Using the Watchdog Function

1.

Installation of AES Driver

2.

Installation of Audio Driver

3.

Installation of LAN Driver

4. Installation of PCI Bridge Driver

5. Installation of VGA Driver

Using the Digital Input Function

Using the Digital Output Function

Key Features

Frequently Answers and Questions

What is the power consumption of the SBC84620?

Does the SBC84620 support remote management capabilities?

What operating systems are compatible with the SBC84620?

Can the SBC84620 be used in industrial automation applications?

What is the maximum storage capacity supported by the SBC84620?

Does the SBC84620 have built-in wireless connectivity?

What is the warranty period for the SBC84620?

Related manuals

AXIOMTEK

SBC8243

AXIOMTEK

SBC84620 Series

AXIOMTEK

SBC81610 VIA C3-800MHz

AXIOMTEK

SBC82400

AXIOMTEK

SBC8354 Pentium All-in-One

AXIOMTEK

SBC817

AXIOMTEK

SBC84820 Series

AXIOMTEK

NA-100

AXIOMTEK

SBC84620

AXIOMTEK

SBC8440