Area SX srl HTTP PUSH SMS Machine User Manual

Area SX srl HTTP PUSH SMS Machine User Manual

Below you will find brief information for SMS Machine HTTP PUSH. The SMS Machine HTTP PUSH is a telecommunication device that allows your Web applications to be quickly integrated with SMS messaging over a GSM network. The new of this updated version is the deployment of WAP PUSH technology that allows sending not only ordinary SMS text messages but also active SMS. This powerful device allows you to send and receive SMS messages, even formatted ones, using a GSM modem and an Ethernet connection. It also provides advanced features for optimizing HTTP communication with the destination script.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

SMS Machine HTTP PUSH User Manual | Manualzz
SMS Machine ® 2009 Area SX srl
http://www.areasx.com
SMS Machine HTTP PUSH
Gateway LAN – SMS with WAP Push Technology
User Manual
Firmware Version 1.0.9
SMS Machine/HTTP Wap Push – User Manual
Page 1
SMS Machine ® 2009 Area SX srl
Congratulation for choosing SMS Machine!
Area SX srl thanks You for the preference you gave us by choosing an SMS Machine device and is
always available for any commercial or technical information.
Contacts
Updated information about SMS Machine devices and latest software release are available on our
Web Site at the address http://www.areasx.com.
http://www.areasx.com
It’s also possible to contact us at the following:
Phone: +39 06.57.17.26.90 and +39 06.57.17.26.79
Fax: +39 06.57.17.26.95
E-mail: [email protected]
SMS Machine/HTTP Wap Push – User Manual
Page 2
SMS Machine ® 2009 Area SX srl
Warnings
Contents and copyright
Information belonging to this manual may be changed or updated without any warning.
Some terms used throughout this document may be other company registered trademark. They are
mentioned only with explanation aim and the intention of respecting authorized owner rights.
Area SX srl will not be considered responsible for eventual damages or losses deriving from this
document wrong information.
SMS Machine is an Area Sx srl registered trademark. All rights reserved.
Safety information
SMS Machine/HTTP PUSH usage may disturb or damage some nearest electronic equipments
operations.
So it is recommended to avoid SMS Machine/HTTP PUSH installation close to:
•
Biomedical electronic devices
•
Aircraft onboard equipments
•
Security devices
•
Audio, radio and television systems
A complete Dual Band GSM Modem is part of SMS Machine/HTTP PUSH.
This device has the same technical characteristics as normal Dual Band cellular phone, so it is
recommended the same usage precautions.
In particular it is recommended not to use SMS Machine/HTTP PUSH wherever it is explicitly forbidden
the use of cellular phone or generic telecommunication equipment.
SMS Machine/HTTP Wap Push – User Manual
Page 3
SMS Machine ® 2009 Area SX srl
Introduction to this manual
This manual is intended for users who have to manage the following kind of SMS Machine:
• SMS Machine/HTTP PUSH
Basic knowledge of computer science, in particular TCP/IP network, is necessary to read this manual.
Updated versions of this manual may be freely downloaded from our web site at the address
http://www.areasx.com.
SMS Machine/HTTP Wap Push – User Manual
Page 4
SMS Machine ® 2009 Area SX srl
Table of contents
Congratulation for choosing SMS Machine!..................................................................................................2
Contacts ............................................................................................................................................................2
Warnings ...........................................................................................................................................................3
Contents and copyright..................................................................................................................................3
Safety information..........................................................................................................................................3
Introduction to this manual .............................................................................................................................4
Product description..........................................................................................................................................7
SMS Machine/HTTP PUSH installation ...........................................................................................................9
Package description ......................................................................................................................................9
Installation requirements..............................................................................................................................10
SIM card insertion........................................................................................................................................10
Connections ....................................................................................................................................................12
Rear panel ...................................................................................................................................................12
GSM antenna connection ............................................................................................................................12
Power supply connection .............................................................................................................................13
Ethernet network connection .......................................................................................................................13
SMS Machine/HTTP turning on .....................................................................................................................14
Front panel...................................................................................................................................................14
Front panel LEDs meaning ..........................................................................................................................14
GSM yellow LED.....................................................................................................................................14
PWR green LED.....................................................................................................................................14
ERR red LED..........................................................................................................................................14
L 1 green LED ........................................................................................................................................14
L 2 green LED ........................................................................................................................................14
SMS Machine/HTTP PUSH configuration .....................................................................................................15
Network configuration ..................................................................................................................................15
Configuration WEB interface .......................................................................................................................15
Get ID Number ............................................................................................................................................17
LAN..............................................................................................................................................................17
IP Address ..............................................................................................................................................17
Netmask .................................................................................................................................................18
Gateway..................................................................................................................................................18
DNS ........................................................................................................................................................18
New password – Repeat password ........................................................................................................18
GSM.............................................................................................................................................................18
Message service center number ............................................................................................................18
HTTP ...........................................................................................................................................................19
Destination server Address ....................................................................................................................19
Destination server Page .........................................................................................................................19
TCP Port number....................................................................................................................................19
Security code ..........................................................................................................................................19
Use HTTP HEAD for script checking......................................................................................................19
Advanced.....................................................................................................................................................20
Maximum server delivery tries................................................................................................................20
Timeout waiting for server answer..........................................................................................................21
Incoming messages buffer length ..........................................................................................................21
Communication parameters name .........................................................................................................21
Current Status..............................................................................................................................................22
GSM Status ............................................................................................................................................23
HTTP Status ...........................................................................................................................................23
Delivery Status........................................................................................................................................23
Other Info................................................................................................................................................24
Configuration test.........................................................................................................................................24
Send an RX simulation ...........................................................................................................................24
Send Message........................................................................................................................................24
Logout..........................................................................................................................................................25
Factory configuration restoring ....................................................................................................................26
SMS Machine/HTTP Wap Push – User Manual
Page 5
SMS Machine ® 2009 Area SX srl
Technical characteristics...............................................................................................................................27
Performances ..............................................................................................................................................27
GSM modem characteristics .......................................................................................................................27
Network microprocessor characteristic .......................................................................................................27
Power adapter electrical characteristics ......................................................................................................27
SMS Machine/http electrical characteristics ................................................................................................27
Technical support...........................................................................................................................................28
SMS Machine Home Page ..........................................................................................................................28
Firmware update..........................................................................................................................................28
Appendix A) HTTP interface .........................................................................................................................29
SMS Machine identification .........................................................................................................................29
SMS reception .............................................................................................................................................29
SMS transmission........................................................................................................................................30
SMS unsuccessful transmission..................................................................................................................31
Configuration ...............................................................................................................................................32
Operation status request .............................................................................................................................32
Network and configuration parameters request...........................................................................................33
SMS reception emulation.............................................................................................................................34
SMS Machine/HTTP Wap Push – User Manual
Page 6
SMS Machine ® 2009 Area SX srl
Product description
SMS Machine/HTTP PUSH is a telecommunication device that allows your Web applications to be
quickly integrated with SMS messaging over GSM network.
The new of this updated version is the deployment of WAP PUSH technology that allows sending not
only ordinary SMS text messages but also active SMS.
In fact the Push mode allows sending SMS messages formatted so they can directly interact with
destination mobile device. In particular it is the parameter called Destination Port that determines the
action to be taken on the terminal.
A typical example is that regarding the hyperlinks sending. An SMS text message containing a link
causes on destination terminal only visualization (only few devices can recognize the link), but an SMS
Push allows notifying directly the information with the option of immediate connection (if this option is
enabled).
Another example needs a further and deeper level of interaction with terminals supporting Java J2ME
applications. In this case, the SMS Push message can be handled directly by the application running
and listening on a specific port so that a related action, according to the message content, may be
executed. For example remote control applications, chat, games, etc.
SMS Machine/HTTP PUSH
In a 125x175x45 mm case, SMS Machine/HTTP PUSH encloses a Quad Band GSM modem, capable
of receiving and sending SMS messages over GSM network, and a network processor with Ethernet
connection, capable of internetworking with Web applications on every platform.
In order to work properly, SMS Machine/HTTP PUSH needs an ordinary SIM card, belonging to any
mobile operator that is qualified to send and receive SMS messages.
On reception: SMS Machine/HTTP PUSH receives SMS on the SIM card inserted in the modem and
it forwards the messages contents towards any Web script (.asp, .php,.pl, .cgi, .jsp, etc..) with an
HTTP POST transaction. Some HTTP parameters will contain the message sender phone number, the
message sending date and text.
On transmission: SMS Machine/HTTP PUSH accepts HTTP transactions in POST mode, it extracts
message text and addressee phone number from HTTP parameters and sends the SMS on GSM
network. Of course among these needed parameters, there is also the port related to the SMS that
determines if it is text message or Wap Push message.
SMS Machine/HTTP Wap Push – User Manual
Page 7
SMS Machine ® 2009 Area SX srl
Connections between SMS Machine/HTTP PUSH and Web Server
Using SMS Machine/HTTP PUSH, there’s no need of serial RS232 modem or managing applications
that run apart the Web Server, but you need only to write simple interface scripts, maybe in the same
programming language you use for the rest of your Web site or application.
SMS Machine/HTTP Wap Push – User Manual
Page 8
SMS Machine ® 2009 Area SX srl
SMS Machine/HTTP PUSH installation
Package description
SMS Machine/HTTP PUSH is delivered inside its cardboard box, well protected from mechanical
shocks that may occur during transport.
Once you opened the package, you will find the following:
1. SMS Machine/HTTP PUSH
2. A set of screws to lock SMS Machine/HTTP PUSH case after SIM insertion in the GSM modem
3. User documentation both the paper one and over a CD
4. A GSM antenna with magnetic base and 2.5m cable
5. A power adapter
SMS Machine/HTTP PUSH package
Each component has been accurately checked before delivering SMS Machine/HTTP PUSH, as
testified by the technical certificate given with the device.
Please avoid using third party components that may damage SMS Machine/HTTP PUSH inner
devices!
SMS Machine/HTTP Wap Push – User Manual
Page 9
SMS Machine ® 2009 Area SX srl
Installation requirements
To succeed in SMS Machine/HTTP PUSH installation, you need:
1. A SIM card belonging to any mobile operator, both prepaid or not. Before inserting the SIM card
into SMS Machine/HTTP PUSH, you should try it with an ordinary mobile phone to verify that it is
able to send and receive SMS and PIN is disabled. You have also to cancel the mobile operator
Service Centre number from the SIM: you will choose it during configuration.
2. A good GSM field level. Before inserting the SIM card into SMS Machine/HTTP PUSH, you should
use it with an ordinary mobile phone to verify that there is a good GSM field level where you will
place the antenna. The provided antenna can be positioned up to 2.5m far from the device so a
better signal coverage can be obtained for a regular operation.
3. Ethernet connection. SMS Machine/HTTP PUSH has a 10Mbit Ethernet socket to be connected
on your LAN by an Hub/Switch. Please be sure that the Hub/Switch socket is 10Mbit or 10/100Mbit.
Beyond physical connection to your network, you need some information about it (IP addresses,
Netmask, Gateway, DNS Server) to configure SMS Machine/HTTP PUSH. So you may need to
refer to your network administrator to collect this kind of information.
4. A 220 VAC power supply.
SIM card insertion
To protect SIM card by accidental removing from the modem during operation, its socket is inside SMS
Machine/HTTP PUSH aluminium case. So to reach SIM card socket, unlock the four screws using a
crossed screwdriver and make the case cover slide ahead as you can see in the next figure.
SMS Machine/HTTP PUSH case opening
Once you opened the case, find the GSM modem and insert the SIM card in its socket with the golden
electric contacts turned towards the bottom and the cut corner ahead, as showed by the sketch on the
modem itself or by the next figure.
SMS Machine/HTTP Wap Push – User Manual
Page 10
SMS Machine ® 2009 Area SX srl
SIM card insertion
Push the SIM card to the bottom of its socket until you will feel a little leap which means it is locked.
When it is necessary to unlock the SIM and release it, you need to slightly push on its edge in the
same direction of insertion. An inner spring will push the SIM card outside enough to grab it.
To close the case, make its cover slide backward paying attention to the signalling LEDs: they must be
correctly aligned to their front panel holes. Now you need to lock the case with the provided four
screws, as shown by the next figure.
SMS Machine/HTTP PUSH case locking
SMS Machine/HTTP Wap Push – User Manual
Page 11
SMS Machine ® 2009 Area SX srl
Connections
Rear panel
Next figure shows a sketch of SMS Machine/HTTP PUSH rear panel. Here the description:
1. FME socket for GSM antenna. In order to protect GSM modem from damage, avoid carefully
turning on SMS Machine/HTTP PUSH without having already connected antenna cable to this
socket.
2. Power supply. Use only the provided power adapter to protect SMS Machine/HTTP PUSH inner
device from damage due to third party component.
3. Power switch
4. Ethernet RJ45 socket for LAN connection, pin hole for link LEDs status checking
5. Entry for optional expansions
6. Button for factory configuration restore
SMS Machine/HTTP PUSH rear panel
GSM antenna connection
Free the provided GSM antenna cable and insert the FME connector into the socket on SMS
Machine/HTTP PUSH rear panel as previously described. This connector has a threaded metal ring
that has to be screwed till the end without forcing.
GSM antenna connection
SMS Machine/HTTP Wap Push – User Manual
Page 12
SMS Machine ® 2009 Area SX srl
Attention!! Avoid absolutely turning on SMS Machine/HTTP PUSH without having already connected
the antenna. Otherwise irreparable damage may occur to the inner GSM modem.
Power supply connection
Insert the power adapter connector on SMS Machine/HTTP PUSH rear panel, then plug it into a power
supply socket. Turn on the switch and check if the green LED on front panel is correctly lit.
Power supply connection
Ethernet network connection
Use an ordinary UTP cable with RJ45 plug to connect SMS Machine/HTTP PUSH to a network
Hub/Switch. Be sure that Hub/Switch socket supports 10Mbit Ethernet devices. After turning on SMS
Machine/HTTP PUSH check if the link LED next the socket is correctly lit. You can see it through the
pin hole next the Ethernet socket on the rear panel.
Network connection
SMS Machine/HTTP Wap Push – User Manual
Page 13
SMS Machine ® 2009 Area SX srl
SMS Machine/HTTP turning on
Once all the connections are realized as previously described, you may turn on SMS Machine/HTTP
PUSH using the switch on the rear panel.
Front panel
On front panel you would be able to see signalling LEDs as the following:
•
GSM LED (yellow) Blinking
•
PWR LED (green) Turned on
•
ERR LED (red) Turned on
•
L 1 and L 2 LED (green) Turned off
After about 30 seconds, ERR red LED has to turn off to showing modem registration over GSM
network and firmware correct operating status. If it doesn’t happen, try to move GSM antenna and turn
on SMS Machine/HTTP PUSH again.
If it doesn’t happen again, be sure you have done the following:
•
Disabled SIM card PIN request, using an ordinary mobile phone
•
Checked that SIM card is qualified
•
Checked that there is good GSM field level where you placed the antenna
Front panel LEDs meaning
GSM yellow LED
This LED shows GSM modem operation. A fast blinking means that the modem is attempting to
register over GSM network. When blinking becomes slower, it means modem is registered and SMS
Machine/HTTP PUSH is ready.
PWR green LED
This LED shows a correct power supply status.
ERR red LED
This LED is on when SMS Machine/HTTP PUSH microprocessor encounters an error. It is also on
when you have just turned on SMS Machine/HTTP PUSH until the modem is registered over GSM
network, then it turns off.
L 1 green LED
This LED shows that SMS Machine/HTTP PUSH is sending or receiving a massage over GSM
network. If L1 and ERR are on together, it means that SIM card is missing or it haven’t been correctly
inserted in the modem.
L 2 green LED
When this LED is turned on, it means that the Web Server for incoming SMS receipt, is unreachable
on the network.
SMS Machine/HTTP Wap Push – User Manual
Page 14
SMS Machine ® 2009 Area SX srl
SMS Machine/HTTP PUSH configuration
Network configuration
First of all, you need to configure SMS Machine/HTTP PUSH with right IP address and netmask in
order to connect it to your network.
SMS Machine/HTTP PUSH has a default network configuration with IP address 192.168.0.101 and
netmask 255.255.0.0.
Be sure that SMS Machine/HTTP PUSH is connected to your LAN through an 10/100Mb Hub/Switch
and your PC IP address is between 192.168.0.1 and 192.168.0.254, except obviously 192.168.0.101,
and netmask is 255.255.0.0.
You may connect your PC and SMS Machine/HTTP PUSH not only through an Hub/Switch, but also
directly with a network crossed cable (CROSS-OVER).
Once your PC is under this condition, you would have to reach SMS Machine/HTTP PUSH by a simple
ping towards its default address 192.168.0.101.
To execute a ping towards SMS Machine/HTTP PUSH, you have to launch a DOS command prompt
and type:
C:>ping 192.168.0.101
If the ping answer is correct, you may go ahead to configuration step.
Configuration WEB interface
Of course, in order to work properly, SMS Machine/HTTP PUSH must be configured as a first step.
This operation is very simple in the current firmware version, since no additional software is needed. In
fact the machine supports a micro web server with a front page developed in Macromedia Flesh, so
you have just to use your favourite browser from a PC and link it toward the machine default IP
address:
http://192.168.0.101
The accessed main page is shown in next picture. No operation is possible yet at this step, but only
status monitor is allowed. In fact the home page summarizes the status of the SMS Machine/HTTP
PUSH and all the displayed parameters will be analyzed in the following sections.
Home page of the SMS Machine web interface
SMS Machine/HTTP Wap Push – User Manual
Page 15
SMS Machine ® 2009 Area SX srl
It is now important to remind that the browser you use must support an appropriate Flash Player.
From the home page you may enter the login page, that is needed to actually execute configuration
operation, simply by clicking on Go to configuration page.
The login page is shown in the following picture, the default password to type in is SMS1234 and then
just clock on Login button.
Login page
If the login is successful, you will enter the functions menu page that you can see in the following
picture. If it is not the case, then check the password or the network settings as described in the
previous section.
Functions menu
Starting from this menu, it possible to access the configuration of all the SMS Machine/HTTP PUSH
parameters. Each configuration interface has a button labeled SAVE, to actually load SMS
Machine/HTTP PUSH with new parameters. Please note that if this buttons is not clicked, SMS
Machine/HTTP PUSH will not be updated with the changes you made.
Machine ID Number window allows SMS Machine/HTTP PUSH identification with its Mac Address.
Each function and configuration parameter description follows.
SMS Machine/HTTP Wap Push – User Manual
Page 16
SMS Machine ® 2009 Area SX srl
Get ID Number
As soon as you logged, SMS Machine/HTTP PUSH identifier is not yet available, as shown in the
windows in the middle of the interface. Clicking on Get ID Number button, it is retrieved with a request
to the SMS Machine/HTTP PUSH. The ID is the Mac Address itself.
To come back to this function, you need to logout and login once again.
SMS Machine/HTTP PUSH ID Number
LAN
This interface allows the configuration of all parameters related to SMS Machine/HTTP PUSH
networking. Be careful in configuring correctly these parameters: in case of mistake, you would not be
able to reach SMS Machine/HTTP PUSH on your network anymore. If it happens, you may follow the
procedure described ahead for factory configuration restoring.
LAN: network parameters configurations
IP Address
It is the new IP address you eventually want to assign to SMS Machine/HTTP PUSH. In fact, if default
IP address 192.168.0.101 doesn’t fit to your network, you may chose whichever other address to
assign to SMS Machine/HTTP PUSH.
SMS Machine/HTTP Wap Push – User Manual
Page 17
SMS Machine ® 2009 Area SX srl
Attention: once changed the IP address or other network parameters, see also next sections, SMS
Machine/HTTP PUSH notifies with a popup that configuration has changed and it reboots network
interface. So it doesn’t respond anymore to menu commands, except for the information stored in
browser cache memory. For this reason you have to logut and link the browser to the new address
assigned to the SMS Machine/HTTP PUSH.
Netmask
It is the netmask of the network where you want to use SMS Machine/HTTP PUSH. Default value is
255.255.0.0. As said before, changing the netmask you need to login once again.
Gateway
It is the IP address of a server able to route on the outside network all the packets not addressed to
local network machines. This parameter must be configured only if SMS Machine/HTTP PUSH needs
to reach a server outside from the local network (e.g. on the Internet).
DNS
It is the IP address of an effective DNS server. This parameter must be configured only if server
names are used instead of their IP address.
New password – Repeat password
These two fields have to be filled with the same string, if it is desired to change SMS Machine/HTTP
PUSH access password. If you forget this password, you may follow the procedure described ahead
for factory configuration restoring.
GSM
This page allows configuring the Service Centre of the Mobile Operator to which belongs the SIM card
used in the SMS Machine/HTTP PUSH.SIM card parameters configuration.
GSM: Service Centre configuration
Message service center number
It is the Service Centre number for SMS sending and it is different from one Mobile Operator to
another. Clicking one of the three major mobile operator logos, you will automatically fill this field.
Please remember to cancel this information from the SIM card, with an ordinary mobile phone, before
using it on SMS Machine/HTTP PUSH.
SMS Machine/HTTP Wap Push – User Manual
Page 18
SMS Machine ® 2009 Area SX srl
HTTP
When an SMS is received, SMS Machine/HTTP PUSH sends its information (message text, sending
number, sending date and optionally an authentication code) to a web server script and cancels it from
the SIM card memory. In other words, the machine works as a browser does when it sends to a web
script some data inserted in a form. So the Machine executes an HTTP/POST request and the
parameters of this page define this communication mode.
HTTP: SMS receipt script configuration
Destination server Address
This parameter must be configured with the IP address or name of the web server where the SMS
Machine/HTTP PUSH sends the received SMS. Please note it must be typed without the http://
protocol, e.g. www.areasx.com or 192.168.0.1.
Destination server Page
This parameter must be configured with the complete path and the name of the script listening on the
Web Server where the SMS Machine/HTTP PUSH sends the received SMS. Please note it must be
typed
with
an
initial
slash
/
and
with
the
classical
nested
path,
e.g.
/SMS_Machine/Received_SMS/rxsms.php.
In other words the two previous parameters joined together form the complete URL used by the SMS
Machine/HTTP PUSH at SMS messages reception.
TCP Port number
It is the port number on which the HTTP request is sent. Default value is 80, “HTTP well kwon port”.
Security code
It is the key word that SMS Machine/HTTP PUSH may use for its authentication to the reception web
script. Of course this value must match the one used by the web script itself.
Use HTTP HEAD for script checking
SMS Machine/HTTP PUSH checks for the availability of the web script destination of the received
SMS, configured as described above. In fact, if the script were unavailable then it would be useless to
start http transaction engaging the microprocessor and its network interface.
This control may be carried out in two ways, depending on this parameter setting.
SMS Machine/HTTP Wap Push – User Manual
Page 19
SMS Machine ® 2009 Area SX srl
If this box is unchecked, then SMS Machine/HTTP PUSH executes the control simply opening and
closing a TCP/IP connection toward the server and its port, configured as described above. On the
contrary if the box is checked, then the script control is deeper and it is carried out using an
HTTP/HEAD request.
Please note that for some web server implementation, this request causes the response of just the
script header without the complete script code execution. For other versions this request may cause
the complete script code execution, so you have to keep in mind and/or verify this aspect when the
option is used.
Enable TCP Server checking
Sometimes it may be useful disabling completely this check, in one of the two ways just described. To
do so, just keep the checkbox not flagged.
Please note that in this case the SMS Machine/HTTP PUSH will always try to send to the Server the
received messages.
Send a POST when a RING is received
The SMS Machine/HTTP PUSH can manage also an incoming call, if the used SIM card is enabled for
voice traffic.
The behaviour of the machine, in case of incoming call, is very similar to that when an SMS is
received. For this reason, please see the next section dedicated to this function for further details.
At this moment, just note that the incoming call managing function is enabled or disabled according to
the selection of this checkbox.
Advanced
Even if the parameters, configured as described in the above sections, are sufficient to let the SMS
Machine/HTTP PUSH work properly, there are also other advanced parameters under the user control
designed to optimized the http communication with the destination script. In this section they will be
described in detail reminding also their default value.
Advanced: advanced parameters of http communication
Maximum server delivery tries
This parameter means the maximum number of attempts that SMS Machine/HTTP PUSH executes for
transmitting the received SMS data toward the destination script. In fact, it is not ensured that the
transaction is successful at the first attempt, for example for a temporary unavailability of the server,
network traffic or, simply, because the script is not correctly configured. In these cases, the machine
SMS Machine/HTTP Wap Push – User Manual
Page 20
SMS Machine ® 2009 Area SX srl
will discard the SMS message, after the number of attempts configured, and passes to manage next
message.
On the contrary, if this parameter is set to 0, the default value, then the SMS Machine/HTTP PUSH will
never discard the message and try forever the transmission to the reception script.
So it is evident that in the first condition an higher speed in transmission of received SMS to the script
can be obtained, but the risk is SMS messages lost in case of discarding for any transient reason of
failed attempts. In the second case, no message will be lost, but the communication could slow down
in difficult condition, for example for exceeding network traffic.
An extreme case is the definite unavailability of the reception script that can cause the overflow of SIM
card memory reserved for received SMS. Then the Service Centre of the Mobile Operator will cease
new delivery attempts, waiting for SIM card memory emptying by the SMS Machine/HTTP PUSH, and
store the exceeding messages for hours, as configured in mobile phone settings typically from 24h to
72h.
Timeout waiting for server answer
This parameter means the maximum time that can pass between an HTTP/POST request, carried out
by the SMS Machine/HTTP PUSH toward the reception script, and the related response with a 200OK.
Once this timeout has expired, the machine assumes the transaction failed and executes the
configured operations as described in previous section: so it tries a new attempt or discards the SMS
message cancelling it from SIM card memory. The unit is millisecond and the default value is 5000 ms
(5 sec).
The criterion in choosing this parameter needs the knowledge of the reception script behaviour in
normal condition (e.g. elaboration delay, delay for database access, etc.) and the network traffic or the
routing delay (e.g. over LAN to Internet).
In fact you have to note that low values for this timeout may speed up the communication, but the risk
is that SMS Machine/HTTP POST assumes as failed simply a slow transaction so causing useless
new transmission attempts. Vice versa, high values for this timeout may slow down the communication
since it takes much time in recognizing the failed ones, but on the other hand prevent from useless
retransmission in case of elaboration/routing delay.
Incoming messages buffer length
The SMS Machine/HTTP PUSH can search for new SMS messages received on the SIM card one by
one or more. In this second case, they will be temporarily stored in a buffer waiting to be forwarded to
the reception script. This parameter just defines the buffer length, default value is 1 and maximum
value is 10.
A larger buffer can speed up reception operations since fewer accesses to SIM card memory are
needed, but on the other hand the risk is messages lost since the buffer memory is cancelled, for
example, if the machine is turned off. On the contrary buffer length value to 1 prevents from messages
lost even in case of accidental machine power down, since they are stored in SIM card memory, but it
could slow down reception operations.
Now it is clear that the reception operations may be speeded up or slowed down rather they may be
more or less reliable, in terms of SMS lost, according to the modulation of three parameters described
above. For this reason it is highly recommended their accurate evaluation according to the condition of
the network where the SMS Machine/HTTP PUSH will work and the service reliability features.
Communication parameters name
Even though the communication http interface used by the Machine will be described in appendix A, by
now it can be already useful to describe, with a certain level of details, the http parameters for the
communication between the Machine and the external application, both for sending and receiving
SMS.
Anyway, please refer to the Appendix for all the details about the new functions: the reception of
extended SMS (also know as chained message, with more than 160 chars), transmission of SMS with
SMS Machine/HTTP Wap Push – User Manual
Page 21
SMS Machine ® 2009 Area SX srl
delivery notification request.
•
Ordinary SMS reception (up to 160 chars)
Web script invoked by SMS Machine/HTTP PUSH must manage four parameters for each received
SMS, using POST method. Name and meaning of these parameters are the following:
o
sms_num is the sending phone number
o
sms_text is the message text
o
sms_date is the date and time of SMS registration on GSM network (i.e. transmission date) in
format YYYY-MM-DD HH:MM:SS +GMT:XX where
o
•
YYYY-MM-DD is the date in format year, month, day
HH:MM:SS is the time in format hour, minute, second
+GMT:XX is the offset from Greenwich time. Sometimes this information is
not correctly managed by mobile operators
sms_code may contain the key word for SMS Machine/HTTP PUSH authentication upon the
web script
Incoming call reception
As briefly described in a previous section, when an incoming call is received by the SMS
Machine/HTTP PUSH then it hangs up and executes the same Http Post request toward the
configured web script and sending the same parameters. Some further details is needed.
•
o
sms_num is the calling phone number
o
sms_text has always the content “INCOMING CALL RECEIVED”
o
sms_date has always a null date as “00-00-00 00:00:00 +GMT:00”
o
sms_code may contain the key word for SMS Machine/HTTP PUSH authentication upon the
web script
Ordinary and extended SMS transmission (up to 300 chars)
For SMS sending, SMS Machine/HTTP PUSH acts like Web server using its smssend.cgi inner script
that accepts four parameters delivered in an HTTP POST transaction. Name and values of these
parameters are the following:
o
num is the addressee phone number
o
text is the message text. 160 chars are available for ordinary SMS, up to 300 for extended
SMS (or chained SMS). The exceeding chars are ignored.
o
Push defines if the SMS message is the normal kind (Push=0) or Wap Push (Push=1 or other
value different form 0). Wap Push kind messages are able to interact with the destination
mobile phone, as already described in previous section. In particular with the value Push=1,
the SMS delivers a hyperlink while different values can interact with J2ME application, for
example. See following sections for the exact message format description when the SMS Wap
Push kind is used
o
Pwd is the script access password and it is the same you use with the login
Current Status
This interface shows some information about SMS Machine/HTTP PUSH current operation status.
Refresh button reloads this information.
SMS Machine/HTTP Wap Push – User Manual
Page 22
SMS Machine ® 2009 Area SX srl
Operation status
GSM Status
•
GSM Field Level
It is an indicator of GSM field just found by SMS Machine/HTTP PUSH modem. This value is
measured in dBm but also a graphical representation is shown.
•
Modem Status
It is a message sent by the modem and it describes the modem status on GSM network.
HTTP Status
•
Lan Status
It is a message that describes SMS Machine/HTTP PUSH status on the local network and the
availability of the destination script.
Delivery Status
In this section you find some counters related to SMS transmission and reception. All these
parameters are not permanent, it means they are set to zero when the SMS Machine is turned off.
•
SMS Received via HTTP
It is a counter of messages sent to the SMS Machine by mean of HTTP POST requests and accepted
in the Microcontroller sending queue.
•
SMS Queued to GSM Modem
It is a counter of SMS messages that the SMS Machine actually sends to its modem, ready to be
transmitted by the SIM card.
•
SMS Received from GSM Modem
It is a counter of messages received by the SIM card inside the SMS Machine/HTTP PUSH modem.
•
SMS sent to the Server
It is a counter of messages received by the SMS Machine and forwarded through HTTP POST
requests to the configured script.
•
SMS Transmissions failed
It is a counter of SMS messages that the SMS Machine wasn’t actually able to delivery to the GSM
SMS Machine/HTTP Wap Push – User Manual
Page 23
SMS Machine ® 2009 Area SX srl
network, for example because of no credit, wrong SMS Center or low field. These messages, after the
sending attempts, are discarded from the queue.
Other Info
It is the firmware version stored in SMS Machine/HTTP PUSH memory.
Configuration test
This page allows you to test SMS Machine/HTTP PUSH settings, both for sending and receiving
messages.
Configuration test page
Send an RX simulation
This is the button to emulate SMS reception and it allows easy checking of HTTP configuration. In fact
SMS Machine makes an HTTP request to the web server and the script you set in HTTP page, using
default parameters.
Send Message
This is the button to make the SMS Machine send a message and so it allows easy checking of the
correct modem working, of the SIM card and of the mobile operator Service Centre setting.
•
Message Text
If you want to send an ordinary SMS, then this field has to be filled with the message text, up to 160
chars available. The Push Destination Port parameter must be left blank or equal to 0 (see also next
items).
If you want to send a Push SMS containing a web-link to the destination mobile phone, then this field
has to be filled with the following format:
www.areasx.com*This is a link to Area SX web site
It means that the format must contain the destination URL (without the http:// protocol) and the text
displayed in the SMS, joined together by the character * without any space. Please note that the Push
Destination Port parameter must be set to 1 (see also next item).
Finally, if you want to send a SMS formatted on a different destination port, then the text will be
composed according with the specific features of the application that will manage it.
•
Destination number
It is the SMS addressee phone number.
SMS Machine/HTTP Wap Push – User Manual
Page 24
SMS Machine ® 2009 Area SX srl
•
Push Destination Port
It is the option indicating the SMS message transmission mode.
If this parameter is set to 0 or it is missing (since 0 is the default value), then a ordinary text SMS will
be sent.
If this parameter is set to 1, then a WAP PUSH SMS message will be sent, driving a hyperlink on the
destination mobile terminal. Of course the text field has to be configured as described above.
Finally, if this parameter is set to other values, then you have to know first that just this port number is
used by the application running on the mobile terminal (typically J2ME) and responsible for
management of SMS messages sent with this format.
Logout
It is the configuration interface exit and then the main page will be shown.
SMS Machine/HTTP Wap Push – User Manual
Page 25
SMS Machine ® 2009 Area SX srl
Factory configuration restoring
Whenever you want, it is possible to restore SMS Machine/HTTP PUSH factory default configuration.
This operation may be useful when it is impossible to access to SMS Machine/HTTP PUSH because,
for example, you forgot IP address or password.
In order to complete this operation follow this procedure:
• Turn off SMS Machine/HTTP PUSH
• Find the reset button on the rear panel, as shown in next figure
• Press this button and keep on pressing it while you turn on SMS Machine/HTTP PUSH again
• Keep on pressing the button and wait until ERR and L2 LEDs are lit at the same time.
This way SMS Machine/HTTP PUSH will restart with all parameters default configuration, in particular
you will access it again using IP address 192.168.0.101 (netmask 255.255.0.0) and password
SMS1234.
Button for factory default configuration restoring
SMS Machine/HTTP Wap Push – User Manual
Page 26
SMS Machine ® 2009 Area SX srl
Technical characteristics
Performances
•
Transmission top speed: 300 SMS per hour
•
Reception top speed: 300 SMS per hour
GSM modem characteristics
•
GSM Modem Telit GM862 Quad band
Network microprocessor characteristic
•
Core module Rabbit Semiconductor RCM3700 16 bit 22Mhz
•
512Kb SRAM memory, 512Kb FLASH memory
•
Ethernet RJ45 10Base-T socket on board
Power adapter electrical characteristics
•
Wall plug
•
Input voltage 230 Volt AC 50-60Hz
•
Output voltage 12 Volt CC/DC 500mA
SMS Machine/http electrical characteristics
•
Average current consumption 300mA
•
SMS Machine/HTTP PUSH operating temperature: 0 – 55 °C
SMS Machine/HTTP Wap Push – User Manual
Page 27
SMS Machine ® 2009 Area SX srl
Technical support
SMS Machine Home Page
At the URL http://www.smsmachine.it you will find all SMS Machine products official home page.
Starting from this page it is possible retrieve the following information:
•
SMS Machine new version announcement
•
Updated version of user documentation
•
Detailed technical documentation
•
PHP, ASP and Visual Basic using examples
•
Support software
If you have any technical or commercial question, you may contact us by mail, phone or fax. Our
references are shown throughout this manual.
Firmware update
SMS Machine/HTTP PUSH firmware is periodically updated by Area SX srl technical staff in order to
improve performances and functionalities.
SMS Machine/HTTP PUSH firmware update availability is announced on the official SMS Machine
home page at the URL www.smsmachine.it or on our company web site www.areasx.com.
For firmware updating, you need optional Rabbit programming cable R101-0542 and its managing
software. These products are available on the same web sites. This cable will be connected, on one
side, to a RS232 serial port of a Windows PC and, on the other side, to the core module Rabbit 3700.
The managing software will download new SMS Machine/HTTP PUSH firmware.
An alternative and easier way to execute firmware update is over the LAN. Contact Area SX for
detailed information.
Further information about Rabbit 3700 Network Processor, that are used on SMS Machine products
are available on web site http://www.rabbitsemiconductor.it
SMS Machine/HTTP Wap Push – User Manual
Page 28
SMS Machine ® 2009 Area SX srl
Appendix A) HTTP interface
In this section all the cgi scripts supported by the SMS Machine/HTTP PUSH will be described in detail
when it acts like an http server, but also its behaviour as an http client. Please note that in the following
sections the device will be simply called with the name SMS Machine.
SMS Machine identification
SMS Machine is identified not only by its IP address, that can be changed as you want, but also by its
Mac Address that cannot be changed. Mac Address is a twelve hexadecimal character string that can
be retrieved by calling an SMS Machine inner CGI script with an http post request as in the following
example:
http://smsmachine_address/queryid.cgi
and sending the parameter
•
Pwd password that allows SMS Machine to accept the transaction
The SMS Machine answers with a string, without any HTML tag but however displayable by a browser,
that contains some pairs of parameter “name=value” tied together by the character &, as in the
following example :
errno=0&desc=Machine ID Reported&MachineId=0090C2D3505A
•
errno is the error code for the transaction, values are 0 if it is OK or 1 for wrong password
•
desc describes shortly the transacion result, for example “Access denied”
•
MachineId (e.g. MachineId = 0090c2c68ab5) is the Mac Address that identifies definitively
SMS Machine
SMS reception
When SMS Machine receives an SMS, message data are sent towards a Web script in an HTTP
POST transaction. This means that SMS Machine emulates a Web browser behaviour when the user
fills a form and submits the data, as already shown in the configuration section dedicated to the HTTP
setting. For example, if you use the following script:
http://www.areasx.com/smstest/rxmsg.php
for each incoming SMS, SMS Machine/HTTP will call rxmsg.php script inside the smstest folder of
www.areasx.com Web server sending four parameters:
•
sms_num SMS sender phone number
•
sms_date SMS sending date with the format YYYY-MM-DD HH:MM:SS +GMT:00
•
sms_text message text
•
sms_code Web script key code (if set during configuration)
SMS Machine/HTTP waits for the standard success answer from the Web server:
HTTP 200 OK
In other cases HTTP transaction is considered incomplete and SMS Machine will act as defined in the
configurations section dedicated to Advanced parameters. Please refer to that section for details.
SMS Machine/HTTP Wap Push – User Manual
Page 29
SMS Machine ® 2009 Area SX srl
Extended SMS reception
The new version of SMS Machine is able to receive also extended messages, also know as chained,
that means SMS with more than 160 chars allowed by the standard.
Anyway, each extended SMS message is actually divided in so much different SMS parts as needed to
fit the whole transmitted text. So the SMS Machine treats all the parts as single messages, executing
an http post for each of them. Obviously new parameters are needed for the original message
“reconstruction”.
Therefore in the HTTP POST request, not only the former parameters just described are sent, but also
the new ones used to identify and reconstruct the extended SMS starting from its component parts:
•
sms_id identification number for the extended SMS
•
sms_totparts number of the extended SMS component parts
•
sms_thispart identification number for the current SMS part
Delivery notification SMS reception
The new version of SMS Machine can also send SMS message requesting the notification of delivery
to the addressee. For this function please see next section. In this section, the reception of the
notification itself will be described.
The reception of a delivery notification is treated as a normal SMS, but its message text will be always
“STATUS REPORT”. Anyway also in this case, new parameters are needed within the HTTP POST
request, in particular:
•
sms_id identification number equal to the index retrieved with the SMS transmission (see also
next section)
•
sms_status status code returned by the GSM network
The expected value for this last parameter is 0x00 that means the status of “SMS delivered”.
Also other values for different network conditions are possible, the most common are the following
ones:
0x00 Short message delivered successfully
0x01 Forwarded, but status unknown
0x20 Congestion, still trying
0x21 Recipient busy, still trying
0x22 No response recipient, still trying
0x23 Service rejected, still trying
0x24 QOS not available, still trying
0x25 Recipient error, still trying
0x42 Connection rejected
0x45 No internetworking available
0x46 Message expired
0x48 Message deleted by SMSC
SMS transmission
When transmitting messages, SMS Machine emulates a Web server behaviour listening on port 80,
while your application has to emulate a Web browser behaviour calling a SMS Machine embedded
CGI. This is the request:
http://smsmachine_address/smssend.cgi
SMS Machine/HTTP Wap Push – User Manual
Page 30
SMS Machine ® 2009 Area SX srl
This request must be carried out in POST mode for sending SMS message parameters which are:
•
Pwd password that allows SMS Machine/HTTP to accept the transaction
•
Push destination port, 0 text SMS (default value if missing), 1 Wap Push, other values to be
specified. Please refer to the section dedicated to SMS sending
•
num SMS addressee phone number
•
text SMS message text. 160 chars are available, up to 300 chars for extended SMS (also known
as chained). The exceeding chars are ignored.
SMS Machine answers with a string, without any HTML tag but however displayable by a browser, that
contains two parameters and their values. The first parameter is errno, followed by its description, and
its values are:
•
errno=0&desc=SMS queued (SMS successfully put in sending queue)
•
errno=1&desc=Access denied (Wrong password)
•
errno=2&desc=Destination number missing (SMS addressee phone number is missing)
•
errno=3&desc=SMS refused (SMS refused because the sending queue is full)
The second parameter is SmsIndex and it is a progressive index that identifies the SMS successfully
put in sending queue.
To verify if the message has been sent by SMS Machine, you may check the SMS sent counters
increment on the Status page. Alternatively you may check the TxGsmCounter and TxServerCounter
parameters retrieved with the getstatus.cgi (see later section).
Delivery notification request
The new version of SMS Machine can also send SMS message requesting the notification of delivery
to the addressee, as mentioned in the previous section. In this case, the HTTP POST request to the
smssend.cgi script must be modified adding the optional parameter:
•
notify values 1 to enable the notification function, 0 or missing for ordinary SMS
SMS unsuccessful transmission
Messages that SMS Machine is not able to send (no GSM field, wrong addressee phone number, etc)
are cancelled from its queue to avoid a blocking status. The SmsIndex parameter allows having trace
of these missing messages by calling an SMS Machine CGI. This is the request:
http://smsmachine_address/smserror.cgi
This request must be carried out in POST mode for sending the following parameter which is:
•
Pwd password that allows SMS Machine to accept the transaction
SMS Machine answers with a string, without any HTML tag but however displayable by a browser, that
looks like the following:
errno=0&Desc=Queue Transimitted&SmsTxErrIdx=2.0.0.0.0.
This string contains the following parameters:
•
Errno, its values are 0 for successful request and 1&desc=Access denied for wrong password
•
SmsTxErrIdx is the dotted list of last five failed SMS index
SMS Machine/HTTP Wap Push – User Manual
Page 31
SMS Machine ® 2009 Area SX srl
Configuration
Also for parameters configuration and for some other support functions, SMS Machine offers some cgi
scripts to be requested by an HTTP client on port 80. These scripts are the same used by the
configuration web interface, developed in Macromedia Flash MX, that is just an HTTP client
communicating with the SMS Machine.
Note that configuration scripts may be useful if you want to integrate SMS Machine configuration
features in your own Web application. In all other cases it is sufficient to use the web interface.
Configuration script is available at the URL:
http://smsmachine_address/setconfig.cgi
Parameters name to send in HTTP POST mode are:
•
Pwd password that allows SMS Machine to accept the transaction, default SMS1234
•
IpAddress IP address to assign to SMS Machine
•
Netmask SMS Machine subnet mask
•
Gateway gateway IP address
•
Nameserver DNS server IP address
•
NewPwd new password to assign to SMS Machine
•
Servicecenter number of the Service Centre for SMS sending
•
ServerAddress IP address or name of the destination server for received SMS
•
ServerPage path of the destination script for received SMS, starting form the server root
•
ServerPort port for HTTP transaction, default value 80
•
ServerCode key code that SMS Machine will use for authentication to Web script
•
ScriptCheck control of the reception script or server, value 1 enables HTTP HEAD request on the
script and value 0 only control on the TCP socket
•
InBufferLen number of SMS in the buffer for transaction to the reception script, default value 1
•
ServerTimeout timeout of the HTTP/TCP connection to the script/server in millisecond, default
value 5000ms
•
MaxFailureIn maximum number of attempts for received SMS forwarding to the script/server,
default value 0 means endless attempts
SMS Machine answers with a string, without any HTML tag but however displayable by a browser, that
contains errno parameter and its description, which values are:
•
errno=0&desc=Configuration_Accepted (Configuration change OK)
•
errno=1&desc=Access denied (wrong password)
Operation status request
SMS Machine supports also a cgi script to retrieve information about its general operating status, at
the following URL:
http://smsmachine_address/getstatus.cgi
This request must be carried out in HTTP POST mode sending the following parameter:
•
Pwd password that allows SMS Machine to accept the transaction
SMS Machine/HTTP Wap Push – User Manual
Page 32
SMS Machine ® 2009 Area SX srl
SMS Machine answers with a string, without any HTML tag but however displayable by a browser, that
is composed by the concatenation of pairs: ‘parameter name’=’value’. Parameters are:
•
errno=0&desc=Configuration Sent (Communication OK) or errno=1&desc=Access denied
(wrong password)
•
GsmFieldLevel GSM field level in dBm
•
LastGsmError modem status or last revealed error
•
TxGsmCounter number of SMS in transmission queued into the modem
•
RxGsmCounter number of SMS in reception received by the modem
•
TxServerCounter number of SMS in transmission queued into the processor
•
RxServerCounter number of SMS in reception forwarded to the server
•
ServerStatus status of the reception script/server
•
Fversion firmware version
•
FailedCounter number of SMS not transmitted by the modem
Network error information coded by the ServerStatus parameter is also shown by the green LED L2 on
front panel.
Failed GSM network registration information coded by the LastGsmError is shown by the long lighting
of red LED ERR on front panel.
The information about failed SMS coded also by the FailedCounter parameter is shown by the
simultaneous blinking of red LED ERR and the green one L1, for some seconds and for each
message.
Network and configuration parameters request
It is possible to retrieve configuration parameters current values by requesting this cgi script:
http://smsmachine_address/queryconfig.cgi
It is also the script used at the login in web interface in order to load all the current parameters. An
HTTP POST request must be used sending the following parameter:
•
Pwd password that allows SMS Machine to accept the transaction
SMS Machine answers with a string, without any HTML tag but however displayable by a browser, that
is composed by the concatenation of pairs: ‘parameter name’=’value’. Parameters are:
•
errno=0&desc=Configuration Sent (correct parameter loading) or
denied (wrong password)
•
IpAddress current IP address of the SMS Machine
•
Netmask SMS Machine subnet mask
•
Gateway gateway IP address
•
Nameserver DNS server IP address
•
Fversion firmware version
•
Servicecenter number of the Service Centre for SMS sending
•
ServerAddress IP address or name of the destination server for received SMS
•
ServerPort port for HTTP transaction, default value 80
•
ServerPage path of the destination script for received SMS, starting form the server root
SMS Machine/HTTP Wap Push – User Manual
errno=1&desc=Access
Page 33
SMS Machine ® 2009 Area SX srl
•
MaxFailureIn maximum number of attempts for received SMS forwarding to the script/server,
default value 0 means endless attempts
•
ServerTimeout timeout of the HTTP/TCP connection to the script/server in millisecond, default
value 5000ms
•
InBufferLen number of SMS in the buffer for transaction to the reception script, default value 1
•
ServerCode key code that SMS Machine will use for authentication to Web script
•
ScriptCheck control of the reception script or server, value 1 enables HTTP HEAD request on the
script and value 0 only control on the TCP socket
SMS reception emulation
It is also available a cgi script that makes SMS Machine emulate SMS reception. This function may be
very useful because it allows checking server configuration without sending any actual SMS. In fact
SMS Machine makes an HTTP request to the web script, you set in HTTP web page, using default
parameters.
This is the URL for the request:
http://smsmachine_address/srvtest.cgi
The parameter to be sent with an HTTP POST request is:
•
Pwd password that allows SMS Machine/HTTP to accept the transaction
Possible SMS Machine responses are:
•
errno=0&desc=SMS queued (emulated SMS successfully queued)
•
errno=1&desc=Access denied (Wrong password)
SMS Machine/HTTP Wap Push – User Manual
Page 34
SMS Machine ® 2009 Area SX srl
SMS Machine/HTTP Wap Push – User Manual
Page 35
SMS Machine ® 2009 Area SX srl
SMS Machine/HTTP PUSH is produced by:
AREA SX SRL
INFORMATICA & MICROELETTRONICA
Via Stefano Longanesi, 25
00146 Roma – ITALIA
Tel. +39 06.99.33.02.57 – Fax +39 06.62.20.27.85
[email protected] - http://www.areasx.com
SMS Machine/HTTP Wap Push – User Manual
Page 36

advertisement

Key Features

  • WAP Push technology support
  • Quad Band GSM modem
  • Ethernet connection
  • Web interface for configuration
  • HTTP/POST communication interface
  • Advanced features for optimizing HTTP communication
  • Incoming call handling
  • SMS delivery notifications

Frequently Answers and Questions

What is the default IP address and netmask for the SMS Machine HTTP PUSH?
The default IP address is 192.168.0.101 and the default Netmask is 255.255.0.0.
How do I configure the Service Centre number for the SIM card used in the SMS Machine HTTP PUSH?
You can configure the Service Centre number by clicking one of the three major mobile operator logos on the GSM configuration page, which will automatically fill the field. Remember to cancel this information from the SIM card before using it on SMS Machine/HTTP PUSH.
What are the parameters that the SMS Machine HTTP PUSH sends to the reception script when an SMS is received?
The SMS Machine HTTP PUSH sends four parameters using POST method: sms_num (sending phone number), sms_text (message text), sms_date (date and time of SMS registration on GSM network), and sms_code (optional key word for SMS Machine/HTTP PUSH authentication).

Related manuals

Download PDF

advertisement