Whirlpool | SH09PGWAX | Instruction for Use | Operating Instructions

Operating Instructions
HOB
GB
GB
English,1
Contents
Installation, 2-7
Positioning
Electrical connection
Gas connection
Data plate
Burner and nozzle specifications
Description of the appliance, 8
Overall view
Start-up and use, 9-10
Practical advice on using the burners
Precautions and tips, 11
SH09PGWAX
General safety
Disposal
Maintenance and care, 12
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Troubleshooting, 13
After sales support, 14
Installation
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
! Intensive and prolonged use may require additional
ventilation, for example, opening a window or
ventilation more efficient by increasing the suction
power
The appliance has the following technical
specifications:
Category: II 2H3+
Positioning
! Keep packaging material out of the reach of children. It
can become a choking or suffocation hazard (see
Precautions and tips).
! The appliance must be installed by a qualified
professional according to the instructions provided.
Incorrect installation may cause harm to people and
animals or may damage property.
! This unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard
Codes Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S.
6891 Current Editions. The following requirements must be
observed:
• The room must be equipped with an air extraction
system that expels any combustion fumes. This may
consist of a hood or an electric fan that automatically
starts each time the appliance is switched on.
The system can also provide the
air needed for combustion
indirectly, i.e. from adjacent
rooms fitted with air circulation
tubes as described above.
However, these rooms must not
Enlarging the ventilation slot
be communal rooms, bedrooms
between window and floor.
or rooms that may present a fire
hazard.
• Liquid petroleum gas sinks to the floor as it is heavier
than air. Therefore, rooms containing LPG cylinders
must also be equipped with vents to allow gas to
escape in the event of a leak. As a result LPG
cylinders, whether partially or completely full, must not
be installed or stored in rooms or storage areas that are
below ground level (cellars, etc.). It is advisable to
keep only the cylinder being used in the room,
positioned so that it is not subject to heat produced by
external sources (ovens, fireplaces, stoves, etc. ) which
could raise the temperature of the cylinder above 50°C.
Adjacent
Room
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Fitting the appliance
Gas and mixed hobs are manufactured with type X
degree protection against overheating. The following
precautions must be taken when installing the hob:
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 50 mm from
the edge of the hob.
• Hoods must be installed according to their relative
installation instruction manuals and at a minimum
distance of 700 mm from the hob.
600mm min.
Directly to
the Outside
• The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The flow of
air must not be less than 2 m3/h per kW of installed
power.
The air circulation system may
take air directly from the outside
by means of a pipe with an inner
cross section of at least 100
A
cm2; the opening must not be
Examples of ventilation holes
vulnerable to any type of
for comburant air.
blockages.
2
Room to be
Vented
540mm min.
! Before operating your new appliance please read this
instruction booklet carefully. It contains important
information for safe use, installation and care of the
appliance.
700mm min.
GB
• Place the wall cabinets
adjacent to the hood at a
minimum height of 540 mm from
the hob (see figure).
If the hob is installed beneath a
wall cabinet, the latter must be
situated at a minimum of 700 mm
above the hob (see figure).
Installation
Make sure you take all the necessary precautions to guarantee
proper installation in compliance with the applicable norms in
force regarding accident-prevention for electrical connection.
For the correct operation of the appliance when built into the
cabinet, it is vital that the minimum distances illustrated in Fig. 1
be respected. The hob features a type Y degree of protection
against overheating in compliance with norms. All surfaces
adjacent to the cabinet and the back panel should be made of
materials resistant to a temperature of 65°C.
m
Min.
M
in.700mm
700m m
50
m
mm
50
2- Built-in hobs (Class 3) with edges lower than 58 mm
(see figure 2, detail H2). To install this type of hob, a
hole large enough to accommodate the whole lower
casing of the appliance must be made on the
worktop intended to be under the hob. Remember to
leave a gap of at least 1 cm between the lower
casing and the worktop around the whole perimeter
of the appliance (the underside of the casing can,
however, touch the surface below it). To fit the
appliances, follow the instructions given above in
point 1 or use any supplementary instruction leaflet
that is provided in special cases.
Fig.1
Securing the appliance to the cabinet
There are three different groups of appliance as far as
installation is concerned:
BUILT-IN HOB
HEIGHT= STEEL THICKNESS
BUILT-IN HOB
STEEL TICKNESS <HEIGHT <58mm
SIT ON - ON HOB
HEIGHT >58mm
Fig.3
FOR MOD: SH09PGWAX
Fig.2
51
1- Built-in hobs to be slotted in (Class 3 - see figure 2,
detail H1). In this case it is necessary to make a
hole in the worktop whose measurements match
those of the hob. The measurement at the side
should be reduced by 1 cm so as to ensure that 1
cm of the perimeter of the hob overlaps with and
rests on top of the supporting surface. To slot in the
hob flush with the worktop, the cut-out on this
supporting surface must be lowered (see figure 4a),
so that both the edge of the hob and the seal under
it can be positioned there. Before fitting the hob to
the worktop, position the seal provided along the
perimeter of the hob. Brackets for fixing hobs to the
cabinet have been provided, and these should be
fitted as shown in detail S (fig.3).
0
86
49
5
0
84
5
Fig.4a
3
GB
GB
3- Sit-on hobs (Class 1) with edges higher than 58 mm
(see figure 2, detail H3). In this case, the lower
casing of the hob does not protrude further than the
edge of the appliance. Even when the hob is resting
on the worktop, it will suffice to leave space for the
gas supply tube and electricity supply cable. To fit
this type of hob, follow the instructions below (fig. 5):
• Fix the two screws provided "A" at a distance from
the back panel as shown in figure 5, leaving the
heads of the screws sticking out of the wood by 1.5
mm.
• Hook the hob onto the two screws "A" and push it
towards the back.
• Fix the appliance to the cabinet at the rear, using the
two brackets "B" and the four screws "C" (these are
all provided).
X mm
Fig.5
X mm
N.B.: to make maintenance operations more efficient,
the area around the hob must be easily accessible after
it has been installed (i.e. there are no completely shutoff elements).
N.B.: An insulating wooden panel should be fitted
beneath the hob, positioned at a minimum of 20 mm
from the hob underside. This wooden panel must be
removable in order to allow for any maintenance
operations beneath the hob.
4
Electrical connection
Gas connection
Hobs equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage
and frequency indicated on the data plate (this is located
on the lower part of the appliance). The earth wire in the
cable has a green and yellow cover. If the appliance is to
be installed above a built-in electric oven, the electrical
connection of the hob and the oven must be carried out
separately, both for electrical safety purposes and to make
extracting the oven easier.
This appliance is designated and set to work with
the gas indicated on the label situated on the type
for which the appliance has been set, proceed with
replacing the corresponding nozzles (provided),
following instruction given in the paragraph
"adaptation to different types ok gas".
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate.
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact
opening of 3 mm installed between the appliance and the
mains. The circuit-breaker must be suitable for the charge
indicated and must comply with current electrical regulations
(the earthing wire must not be interrupted by the circuitbreaker). The supply cable must not come into contact with
surfaces with temperatures higher than 50°C.
! The installer must ensure that the correct electrical
connection has been made and that it is compliant with
safety regulations.
Before connecting to the power supply, make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate.
• The voltage is in the range between the values indicated
on the data plate.
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (Should assistance be
required, please telephone Scholtès Assistance free
number 0800 158 55 00).
! The manufacturer declines any liability should these
safety measures not be observed.
GB
The appliance should be connected to the main gas
supply or to a gas cylinder in compliance with current
national regulations. Before carrying out the connection,
make sure the cooker is compatible with the gas supply
you wish to use. If this is not the case, follow the
instructions indicated in the paragraph “Adapting to
different types of gas.”
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
! Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (“Burner and nozzle
specifications”). This will ensure the safe operation and
longevity of your appliance while maintaining efficient
energy consumption.
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in
such a way as not to place any strain of any kind on the
appliance.
There is an adjustable L-shaped pipe fitting on the
appliance supply ramp and this is fitted with a seal in order
to prevent leaks. The seal must always be replaced after
rotating the pipe fitting (seal provided with appliance). The
gas supply pipe fitting is a threaded 1/2 gas cylindrical
male attachment.
Connecting a flexible jointless stainless steel
pipe to a threaded attachment
The gas supply pipe fitting is a threaded 1/2 gas
cylindrical male attachment.
These pipes must be installed so that they are never
longer than 2000 mm when fully extended. Once
connection has been carried out, make sure that the
flexible metal pipe does not touch any moving parts and is
not compressed.
! Only use pipes and seals that comply with current
national regulations.
Checking the tightness of the connection
! When the installation process is complete, check the
pipe fittings for leaks using a soapy solution. Never use a
flame.
5
GB
Adapting to different types of gas
To adapt the hob to a different type of gas other than
default type (indicated on the rating plate at the base of
the hob or on the packaging), the burner nozzles should
be replaced as follows:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 “Burner and nozzle characteristics”).
3. Reassemble the parts following the above procedure in
the reverse order.
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.
! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.
! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).
4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.
Replacing the nozzles on separate double crown
wok burners:
1. remove the grids and slide the burners from their
housings. The burner consists of 2 separate parts (see
figure);
2. unscrew the burers with a 7 mm wrench spanner. The
internal burner has a nozzle, the external burner has
two (of the same size). Replace the nozzle with models
suited to the new type of gas (see table 1).
3. replace all the components by repeating the steps in
reverse order
• Adjusting the burners’ primary air :
Does not require adjusting.
• Setting the burners to minimum:
1. Turn the tap to the low flame position.
2. Remove the knob and adjust the adjustment screw,
which is positioned in or next to the tap pin, until the
flame is small but steady.
3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are
set to the low flame setting, increase this low flame
setting using the adjusting screw.
6
DATA PLATE
Electrical
connections
voltage of 220-240V ~ 50/60Hz
(see data plate )
This appliance conforms to the
following European Economic
Community directives:
-2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent
amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2009/142/EEC dated 30/11/09
(Gas) and subsequent
amendments.
- 2002/96/EC and subsequent
amendments.
Burner and nozzle specifications
Table 1
Liquid Gas
Burner
Diameter Thermal power
(mm)
kW (p.c.s.*)
By-Pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzle
1/100
Nomin.
Ridot.
(mm)
(mm)
***
**
(mm)
Flow*
l/h
B. Semi fast
75
1,65
0,40
30
64
138
136
96
181
A. Auxiliary
55
1,00
0,40
30
50
73
71
71
95
C. Oval burner
—
1,50
0,40
30
60
109
107
88
143
D. Double
crown wok
(inner DCDR)
30
0,90
0,40
30
44
65
64
70
86
D. Double
crown wok
(outer DCDR)
2 nozzle
130
4,10
1,30
57
70
298
293
110
390
28-30
20
35
37
25
45
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
Supply
Pressures
*
**
***
At 15°C and
Propane
Butane
Natural
GB
Natural Gas
20
17
25
1013 mbar - dry gas
P.C.S. = 50.37 MJ/Kg
P.C.S. = 49.47 MJ/Kg
P.C.S. = 37.78 MJ/m3
! The hob can only be installed above built-in ovens with a cooling ventilation system.
C
B
D
C
A
7
Description of the
appliance
GB
Overall view
Gas burners
Pan supports
Control knobs
Flame supervision
device
• Gas burners differ in size and power as described
in the previous page. Use the diameter of the
cookware to choose the most appropriate burner
to cook with.
• Control knobs allow to adjust the power or the size
of the flame.
• The ignition enables a specific burner to be lit
automatically when a knob is pushed down ad
turned.
• The flame supervision device is a safety device
that automatically shuts off the supply of gas to
the affected burner if the flame is extinguished for
any reason, preventing potential gas leaks.
8
Ignition
Start-up and use
! The position of the corresponding gas burner is
shown on every knob.
Gas burners
Each burner can be adjusted to one of the following
settings using the corresponding control knob:
z
Off
Maximum
Minimum
To light each of the burners, press down the
corresponding knob and turn it anti-clockwise to the
maximum setting.
Since each burner is fitted with a flame supervision
device, the knob should be pressed and held for
approximately 2-3 seconds to allow the automatic
device keeping the flame alight to heat up.
! When there is no electricity supply, the burners
can be lit with a match after turning the control
knob to the flame position.
To turn on one of the burners, place a lighted match
or lighter near the burner, press the knob all the way
in and turn it anti-clockwise to the "High" setting.
To turn on one of the burners press the relevant
knob all the way down and turn it anti-clockwise to
the full setting. To adjust the power of the burner
and turn it off, follow the instructions previously
described.
GB
Practical advice on using the burners
To ensure the burners operate efficiently:
• Use appropriate cookware for each burner (see
table below) so that the flames do not extend
beyond the bottom of the cookware.
• Always use cookware with a flat base.
• This product is supplied with a specifically
designed Wok stand. Placed on the special
Double crown burner, the support will allow the
use of larger wok pans, with non flat base,
providing stability.
• When the contents of the pan reach boiling point,
turn the knob to minimum.
Burner
ø Cookware diameter
(cm)
B. Semi Fast
16 - 22
A. Auxilliary
10 - 14
! If a flame is accidentally extinguished, turn off the
control knob and wait for at least 1 minute before
trying to relight it.
C. Oval burner
16 - 22
D. Double crown wok
(inner DCDR)
10 -14
To switch off the burner, turn the knob clockwise until
it stops (when reaches the “z” position).
D. Double crown wok
(outer DCDR)
26 - 28
Double crown wok burner
This burner consists of two concentric burners which
can operate either together or separately.
Use of the double crown wok burner on the
maximum setting gives a very high power which
reduces cooking times with respect to conventional
burners.
Moreover the double crown wok provides a more
uniform distribution of heat on the bottom of the pan,
when using both burners on minimum.
To ensure that the double crown wok is used to its
full potential, never set the inside ring to minimum
and the outside ring to maximum at the same time.
Pots and pans of all sizes can be used. In the case
of the smaller pots and pans we recommend the use
of only the internal burner.
There is a separate control knob for each of the
parts of the double crown wok burner.
! Make sure the pans do not overlap the edges of
the hob while it is being used
! This hob is supplied with a pan support adaptor.
This accessory should be used to increase the
stability on the Double crown wok burner when only
the inner part (inner DCDR) is operated and there is
the need to place small pans (under 12 cm
diameter) on it.
To identify the type of burner, refer to the designs in
the section entitled, "Burner and Nozzle
Specifications".
The knob marked by the symbol
external burner;
operates the
The knob marked by the symbol
internal burner.
operates the
9
GB
Practical advice on using the Oval burners
The two Oval burners have been designed to
increase the flexibility of your hob. They can be
used as individual burners, to cook with two pans at
the same time (Fig. A), or they can be turned 90°
and used together (Fig. B). This second option is
ideal when using the special cast iron Griddle
supplied with the hob or the optional Teppan Yaki,
as well as with a long pan, or fish kettle.
To turn the two burners 90°, proceed as follows:
• Make sure that the burners are cool;
• Lift the burner completely out of its housing;
• Replace it in its housing in the position desired;
• Make sure that the burners are positioned
correctly before use.
Fig. A
Fig. B
With the prolonged use of the Griddle or Teppan
Yaki, the surface of the hob may become yellow. To
prevent this, it is recommended to clean it with the
Steel Care specific cream provided with the hob.
If assistance is required, or to order another bottle of
the cleaning product, telephone Scholtès Assistence
free number 0800 158 55 00.
10
Precautions and tips
! This appliance has been designed and
manufactured in compliance with international safety
standards. The following warnings are provided for
safety reasons and must be read carefully.
General safety
• This is a appliance.
-Class 1: all models with edges that are higher than 58 mm
(see overleaf, fig. 4, detail H3).
-Class 3: all models with edges that are lower than 58 mm
(see overleaf, fig. 4, details H1 and H2).
• Gas appliances require regular air exchange to
maintain efficient operation. When installing the
hob, follow the instructions provided in the
paragraph on “Positioning” the appliance.
• These instructions are only valid for the countries
whose symbols appear in the manual and on the
serial number plate.
• The appliance is designed for domestic use inside
the home and is not intended for commercial or
industrial use.
• The appliance must not be installed outdoors, even
in covered areas. It is extremely dangerous to leave
the appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with
wet or damp hands and feet.
• The appliance must be used by adults only, to cook
food according to the instructions in this manual.
• Ensure that the power supply cables of other
electrical appliances do not come into contact with
the hot parts of the oven.
• The openings used for ventilation and dispersion of
heat must never be covered.
• Do not use unstable or deformed pans.
• Do not let children play with the appliance.
• The appliance should not be operated by people
(including children) with reduced physical,
sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with
the product. These individuals should, at the very
least, be supervised by someone who assumes
responsibility for their safety or receive
preliminary instructions relating to the operation of
the appliance.
Disposal
• When disposing of packaging material: observe
local legislation so that the packaging may be
reused.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE),
requires that old household electrical appliances
must not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be
collected separately in order to optimise the
recovery and recycling of the materials they
contain and reduce the impact on human health
and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance
it must be separately collected.
Consumers may take their old appliance to public
waste collection areas, other communal collection
areas, or if national legislation allows return it to a
retailer when purchasing a similar new product.
All major household appliance manufacturers are
active in the creation of systems to manage the
collection and disposal of old appliances.
• Always make sure the knobs are in the “z”
position when the appliance is not in use.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Never carry out any cleaning or maintenance work
without having detached the plug from the mains.
• In case of malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the
appliance. Should assistance be required, please
telephone Scholtès Assistance free number 0800
158 55 00.
• Always make sure that pan handles are turned
towards the centre of the hob in order to avoid
accidental burns.
11
GB
Maintenance and care
GB
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents such
as stain removers, anti-rust products, powder
detergents or sponges with abrasive surfaces: these
may scratch the surface beyond repair.
! Never use steam cleaners or pressure cleaners on
the appliance.
• It is usually enough to wash the hob with a damp
sponge and dry it with absorbent kitchen roll.
• The removable parts of the burners should be
washed frequently with warm water and soap and
any burnt-on substances removed.
• For hobs which ligth automatically, the terminal
part of the electronic instant lighting devices
should be cleaned frequently and the gas outlet
holes should be checked for blockages.
• Stainless steel can be marked by hard water that
has been left on the surface for a long time, or by
aggressive detergents containing phosphorus.
After cleaning, rinse and dry any remaining drops
of water.
Gas tap maintenance
Over time, the taps may become jammed or difficult
to turn. If this happens, the tap must be replaced.
! This procedure must be performed by a qualified
technician authorised by the manufacturer.
12
Troubleshooting
It may happen that the appliance does not function properly or at all. Before calling the service centre for
assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and
electrical supplies, and, in particular, that the gas valves for the mains are open.
GB
Problem
Possible causes/Solution
The burner does not light or the flame is not
even around the burner.
• The gas holes on the burner are clogged.
• Make sure that all the movable parts that make up
the burner are mounted correctly.
• There are draughts near the appliance.
The flame dies in models with a safety device.
• Make sure that you have pressed the knob all the
way in.
• Make sure that you keep the knob pressed in long
enough to activate the safety device.
• Make sure that the gas holes are not blocked in
the area corresponding to the safety device.
The burner does not remain lit when set to
minimum.
• The gas holes are not blocked.
• Make sure that there are no draughts near the
appliance.
• Make sure that the minimum setting has been
adjusted properly.
The cookware is unstable.
• Make sure that the bottom of the cookware is
perfectly flat.
• Make sure that the cookware is positioned
correctly at the centre of the burner.
• Make sure that the pan support grids have been
positioned correctly.
If, despite all these checks, the hob does not function properly and the problem persists, please telephone
Scholtès Assistance free number 0800 158 55 00. Please have the product model number handy.
This Information can be found in the first page of the blooklet.
! Never use unauthorised technicians and never accept replacement parts which are not original.
13
After sales support
Scholtès UK | Morley Way, Peterborough, PE2 9JB
t. 0800 158 55 00 e. info@scholtes.co.uk w. scholtes.co.uk
GB
Commitment to after sales support
Thank you for investing in Scholtès
Scholtès products are designed to perform consistently and reliably throughout their life.
To give you further reassurance Scholtès ensures your appliance benefits from a five year guarantee.
This promise means, that if within five years from the date of purchase of your appliance it is proven to be
defective Scholtès will, at its discretion, repair or replace the appliance at no additional cost.
Contact
There is a dedicated team of advisors to provide free advice and assistance with any problem you experience
with a Scholtès appliance. Where necessary, Scholtès will arrange for an engineer from its specialist field support
team to resolve the issue with the least disruption.
Telephone free on 0800 158 55 00
To help manage potential problems quickly and effectively Scholtès recommends registering all appliances.
To register appliances, telephone free on 0800 158 55 00 or visit www.scholtes.co.uk.
This guarantee is subject to the following conditions:
• The appliance has been installed and operated correctly and in accordance with the operating and
maintenance instructions
• The appliance is used only on the electricity or gas supply printed on the rating plate.
• The appliance has been used for normal domestic purposes only.
• The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by Scholtès.
• Any repair work be undertaken by Scholtès or an appointed agent
• Any parts removed during repair work or any appliance that is replaced becomes the property of Scholtès.
• The appliance is used in the United Kingdom or Republic of Ireland
The guarantee does not cover:
• Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation
• Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters
• Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON
DOMESTIC PREMISES.
14
GB
15
03/2010 - 195082269.01
XEROX FABRIANO
GB
16
Download PDF

advertising