Elmo Rietschle V-Series V-VTN 16, V-VTN 26, V-VTN 41 vacuum pump Operating Instructions

Elmo Rietschle V-Series V-VTN 16, V-VTN 26, V-VTN 41 vacuum pump Operating Instructions

The V-Series V-VTN 16, V-Series V-VTN 26, V-Series V-VTN 41 are dry running rotary vane vacuum pumps suitable for evacuating closed systems and for a permanent vacuum in the intake pressure range 150 - 1000 mbars (abs.). The pumping capacity with unrestricted suction is 15, 25 and 40 m3/h at 50 Hz.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Elmo Rietschle V-Series V-VTN 16, V-Series V-VTN 26, V-Series V-VTN 41 Operating Instructions | Manualzz
Edition: 1.1.2012 · BA 281-EN
Original Operating Instructions
V-VTN
V
V-VTN 16 | 26 | 41
V-Serie
V-Series
Drehschieber
Rotary Vane
Table of contents
Table of contents
1
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplier documentation and accompanying documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directives, standards, laws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and meaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical terms and meaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
4
4
5
5
5
2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Warning instruction markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unacceptable operating modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personal qualifications and training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety-conscious work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety notes for the operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety instructions for installing, commissioning and maintenance . . . . . . . . . . . . . . . . . . . . . .
Guarantee conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
7
7
8
8
8
9
9
3
Transport, storage and disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
3.1
3.3
Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Unpack and check the delivery condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2
Lifting and transporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Ambient conditions for storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
11
11
11
4
Set up and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
4.1
4.2
4.3
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1
Data plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Areas of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
14
14
14
5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
5.1
5.2
5.3
5.4
5.5
Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control and relief valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
16
17
6
Commissioning and decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
6.1
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1
Checking the rotation direction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decommissioning/ storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Re-commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
19
19
3.2
6.2
6.3
2
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Table of contents
7
Maintenance and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
7.1
7.2
7.3
7.4
Ensuring operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1
Air filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2
Replacing blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reparatur/ Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
21
22
23
24
8
Malfunctions: Causes and elimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
9
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
|
3
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Foreword
1
Foreword
1.1
Principles
These operating instructions:
1.2
•
are a part of the following dry running rotary
vane vacuum pumps V-VTN 16, V-VTN 26 and
V-VTN 41.
•
describe how to use them safely and properly in
all life phases.
•
must be available where the equipment is used.
Target group
The target group for these instructions is technically
trained specialists.
1.3
Supplier documentation and accompanying documents
Document
Contents
No.
Operating Instructions
BA 281-EN
Declaration of Conformit
C 0083-EN
Declaration of harmlessness
7.7025.003.17
Spare parts’ list
Spare parts’ document
E 281
Data sheet
Technical data and graphs
D 281
Info sheet
Storage guidelines for machines
I 150
Manufacturer’s declaration
EU Directive 2002/95/EG (RoHS)
—
Supplier documentation
1.4
Abbreviations
Fig.
Figure
V-VTN
Vacuum pump
3
1.5
m /h
Pumping capacity
mbar (abs.)
Final vacuum, operating vacuum
Directives, standards, laws
See Conformity Declaration
4
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Foreword
1.6
Symbols and meaning
Symbol
Explanation
Condition, pre-requisite
####
a), b),...
Instructions, action
Instructions in several steps
Results
[-> 14]
Cross reference with page number
Information, note
Safety symbol
Warns of potential risk of injury
Obey all the safety instructions with this symbol in order to avoid injury
and death.
1.7
Technical terms and meaning
Term
Explanation
Machine
Pump and motor combination ready to be connected
Motor
Pump drive motor
Vacuum pump
Machine to create a vacuum
Rotary vane
Machine’s design or active principle
Pumping capacity
Vacuum pump volume flow related to the condition in the suction connection
Final pressure (abs.)
The maximum vacuum that a pump reaches when the suction opening is
closed. Given as absolute pressure.
Permanent vacuum
The vacuum or the suction range at which the pump operates permanently.
The permanent vacuum or intake pressure is ≥ than the final vacuum and
< than the atmospheric pressure..
Noise emission
1.8
The noise emitted at a specific loading given as a figure, sound pressure
level dB(A) as per EN ISO 3744.
Copyright
Passing on or copying this document, using and
providing information on its contents are prohibited
unless expressly permitted.
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
5
Safety
2
Safety
The manufacturer is not responsible for damage if
you do not follow all of this documentation.
2.1
Warning instruction markings
Warning
Danger level
Consequences if not obeyed
DANGER
immediately imminent danger
Death, severe bodily injury
WARNING
possible imminent danger
Death, severe bodily injury
CAUTION
possible hazardous situation
Slight bodily injury
possible hazardous situation
Material damage
NOTICE
2.2
General
These operating instructions contain basic instructions for installation, commissioning, maintenance
and inspection work which must be obeyed to ensure the safe operation of the machine and prevent
physical and material damage.
The safety instructions in all sections must be taken
into consideration.
The operating instructions must be read by the
responsible technical personnel/ operator before
installing and commissioning and must be fully understood. The contents of the operating instructions
must always be available on site for the technical
personnel / operator. Instructions fixed directly onto
the machine must be obeyed and must always remain legible. This applies for example to:
•
Symbols for connections
•
Data and motor data plate
•
Instruction and warning plates
The operator is responsible for observing local regulations.
6
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Safety
2.3
Designated use
The machine must only be operated in such areas
as are described in the operating instructions:
2.4
•
only operate the machine in a technically perfect
condition
•
do not operate the machine when it is only partially assembled
•
the machine must only be operated at an ambient temperature and suction temperature of
between 5 and 40°C. Please contact us for
temperatures outside this range.
•
the machine may convey, compress or extract
the following media:
• convey air with a relative humidity of 30 90%
• all non-explosive, non-inflammable, non-aggressive and non-poisonous dry gases and
gas air mixtures
•
extracting, conveying and compressing explosive, inflammable, aggressive or poisonous media, e.g. dust as per ATEX zone 20-22, solvents
as well as gaseous oxygen and other oxidants,
extremely damp air, water vapour, traces of oil,
oil vapour and grease
•
using the machine in non-commercial plants if
the necessary precautions and protective measures have not been taken in the plant
•
installing in environments that are at risk of explosions
•
using the machine in areas with ionising radiation
•
back pressures on the outlet side of more than
+0,1bars
•
modifications to the machine and accessories
Unacceptable operating modes
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
7
Safety
2.5
Personal qualifications and training
•
Ensure that people entrusted with working on
the machine have read and understood these
operating instructions before starting work,
particularly the safety instructions for installation,
commissioning, maintenance and inspection
work.
•
Manage the responsibilities, competence and
monitoring of staff
•
all work must only be carried out be technical
specialists:
• Installation, commissioning, maintenance
and inspection work
• Working with electricity
•
2.6
personnel being trained to work on the machine must be supervised by technical specialists only
Safety-conscious work
The following safety regulations apply in addition
to the safety instructions and intended use listed in
these instructions:
2.7
8
•
Accident prevention regulations, safety and operating regulations
•
the standards and laws in force
•
hot parts of the machine must not be accessible
during operation or must be fitted with a guard
•
People must not be endangered by the free
extraction or discharge of pumped media
•
Risks arising from electrical energy must be
eliminated.
•
The machine must not be in touch with inflammable substances.
Danger of fire by hot surfaces, discharge of
pumped media or cooling air
Safety notes for the operator
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Safety
2.8
2.9
Safety instructions for installing, commissioning and maintenance
•
The operator will ensure that any installation,
commissioning and maintenance work is carried out by authorised, qualified specialists who
have gained sufficient information by an in-depth
study of the operating instructions.
•
Only work on the machine when it is idle and
cannot be switched on again
•
Ensure that you follow the procedure for decommissioning the machine described in the operating instructions.
•
Fit or start up safety and protective devices
again immediately after finishing work.
•
Conversion work or modifications to the machine are only permissible with the manufacturer’s consent.
•
Only use original parts or parts approved by the
manufacturer. The use of other parts may invalidate liability for any consequences arising.
•
Keep unauthorised people away from the machine
Guarantee conditions
The manufacturer’s guarantee or warranty will no
longer apply in the following cases:
•
Improper use
•
Not complying with these instructions
•
Operation by insufficiently qualified staff
•
Using spare parts that have not been approved
by Gardner Denver Schopfheim GmbH
•
Unauthorised modifications to the machine or
the accessories supplied by Gardner Denver
Schopfheim GmbH
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
9
Transport, Lagerung und Entsorgung
3
Transport, storage and disposal
3.1
Transportation
3.1.1 Unpack and check the delivery condition
a) Unpack the machine on receipt and check for
transport damage.
b) Notify the manufacturer of transport damage immediately
c) Dispose of the packaging in accordance with the
local regulations in force.
3.1.2 Lifting and transporting
WARNING
Death or limbs crushed as a result of the items
being transported falling or tipping over.
a)
b)
c)
d)
When transporting with the lifting device remember:
Select the lifting device suitable for the total
weight to be transported.
Ensure that the machine cannot tip and fall.
Do not stop under a suspended load.
Put the goods to be conveyed on a horizontal
base.
Lifting device/ Transporting with a crane
WARNING
Bodily injury resulting from improper operation
a) Loads crosswise to the ring level are not permitted.
b) Avoid impact stress.
1
a) Tighten the eyebolts (Fig. 1/1) firmly.
b) The machine must be suspended on the eyebolt
using the lifting device for lifting and transporting.
Fig. 1
Lifting and transporting
1
10
Eyebolt
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Transport, Lagerung und Entsorgung
3.2
Storage
NOTICE
Material damage caused by improper storage.
Ensure that the storage area meets the following
conditions:
a) dust free
b) vibration free
3.2.1 Ambient conditions for storage
Ambient conditions
Value
Relative humidity
0% to 80%
Lagertemperatur
-10°C to +60°C
The machine must be stored in a dry environment
with normal air humidity. It should not be stored for
more than 6 months.
see Info “Machine storage guidelines”, Page 4
3.3
Disposal
WARNING
Danger from inflammable, corrosive or poisonous substances.
Machines that come into contact with hazardous substances must be decontaminated before
disposal.
a)
b)
c)
d)
e)
When disposing ensure the following:
Collect oils and grease separately and dispose
of in accordance with the local regulations in
force.
Do not mix solvents, limescale removers and
paint residues
Remove components and dispose of them in
accordance with the local regulations in force.
Dispose of the machine in accordance with the
national and local regulations in force.
Parts subject to wear and tear (marked as such
in the spare parts list) are special waste and
must be disposed of in accordance with the
national and local waste laws.
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
11
Set up and operation
4
Set up and operation
4.1
Setup
V-VTN (01)
C1
B
A
E
E
F
F
N
G
V-VTN (02)
C
Fig. 2
Vacuum pump V-VTN (01) / V-VTN (02
A
Vacuum connection
E
Cooling air inlet
B
Exhaust air outlet
F
Cooling air outlet
C
Vacuum regulating valve
N
Data plate
C1
Vacuum safety valve
12
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Set up and operation
O
N
G1
G
J
Fig. 3 Vacuum pump V-VTN
G
Outlet grid
N
Data plate
G1
Inlet grating
O
Rotation direction arrow
J
Plug connection (optional)
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
13
Set up and operation
4.1.1 Data plate
1
2
3
4
5
616&
7<3971
,'
PEDUDEV
PñK
79“
$ +]
—)
(1 ,V.O ) ,3 N:
PLQ
6
0DGHLQ*HUPDQ\5RJJHQEDFKVWUDVVH'6FKRSIKHLP
10
9
8
7
6
1
Type/ Size (mechanical version)
2
Serial number
3
Year of construction
4
Item no.
5
Final pressure (abs.)
6
Pumping capacity
7
Motor data
8
Speed
9
Motor output
10
Operating mode
Fig. 4 Data plate
4.2
Description
The V-VTN model range has a connecting thread on the suction side and an exhaust silencer on the pressure side. The aspirated air is cleaned by an inbuilt fine micro filter.
The motor and the pump have a common shaft.
The vacuum pumps V-VTN are located in a plastic sound cover. Inside the sound cover is also a fan that
provides cooling.
The V-VTN (02) has a vacuum regulating valve fitted as standard (Fig. 2/C) that enables the vacuum to be set
to the required values which have an upper limit.
4.3
Areas of application
These dry running rotary vane vacuum pumps V-VTN 16 to V-VTN 41 are suitable for evacuating closed systems and for a permanent vacuum in the intake pressure range 150 - 1000 mbars (abs.).
The pumping capacity with unrestricted suction is 15, 25 and 40 m3/h at 50 Hz. Data sheet D 281 shows the
dependency of the pumping capacity on the intake pressure
These dry running machines are suitable for conveying air with a relative humidity of 30 - 90%.
If the unit is switched on more frequently (at regular intervals of about 10 times an hour) or at
higher ambient temperatures and intake temperatures, the excess temperature limit of the motor
winding and the bearings may be exceeded.
Please contact the manufacturer should the unit be used under such conditions.
If it is installed in the open air the unit must be protected from environmental influences, (e.g. by a
protective roof).
14
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Installation
5
Installation
5.1
Preparing for installation
Check the following points:
•
•
Machine freely accessible from all sides
Do not close ventilation grids and holes
•
Sufficient room for installing and removing pipes
and for maintenance work, particularly for installing and dismantling the machine
•
No external vibration effect
•
Do not suck any hot exhaust air from other machines into the cooling system.
To remove the outlet grid (Fig. 3/G) and the inlet grating (Fig. 3/G1) at least 30 cm of space must
be available for maintenance work. You must also ensure that the cooling air inlets (Fig. 2/E) must
be at least 10 cm away from the nearest wall (outgoing cooling air must not be sucked in again).
5.2
Installation
NOTICE
The machine may only be operated when it is
set up horizontally.
Other installation on request.
Material damage resulting from the machine
tipping over and falling.
When installed at more than 1000 m above sea
level a reduction in power is noticeable. In this
case we would ask you to contact us.
Ensure that the foundation complies with the following conditions:
•
Level and straight
•
The bearing surface must be able to bear the
weight of the machine
It must be possible to install the machine on a firm foundation without anchoring. When installing
on a substructure we recommend fixing with flexible buffers.
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
15
Installation
5.3
Connecting pipes
a) Vacuum connection at (Fig. 2/A).
NOTICE
Material damage resulting from the forces and
torques of the pipes on the unit being too high.
screw pipes in by hand.
The pumping capacity of the vacuum pump
is reduced if the suction pipe is too narrow
and/or too long.
b) Check to ensure the suction pipe is connected
correctly.
NOTICE
Length of the connection pipes
With connection pipes that have the same pipe
cross section as the machine connection and are
more than 3m long, a non-return valve especially
for the purpose must be installed in order to avoid
reverse operation when the machine has stopped.
5.4
Control and relief valve
The vacuum can be set by turning the control knob
(Fig. 2/C) as shown on the symbol fitted to the button.
NOTICE
Do not operate without the standard control
and relief valve.
If the permissible vacuum is exceeded (see data
plate) the machine may be damaged.
16
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Installation
5.5
Connecting the motor
DANGER
Danger of death if the electrical installation has
not been done professionally.
The electrical installation must only be done by a
qualified electrician observing EN 60204. The operating company has to provide the main switch.
a) The electrical motor data can be found on the
data plate (Fig. 2/N) or the motor data plate. The
motors comply with DIN EN 60034 and are in
protection class IP 55 and insulation class F. The
appropriate connection diagram is located in the
motor‘s terminal box (not for the plug connection version). The motor data must be compared
with the data of the existing mains network (current type, voltage, network frequency, permitted
current value).
b) Connect the motor via the plug connection
(Fig. 3/J) or a motor protection switch (for safety
reasons a motor protection switch is required
and cable fitting must be provided to provide
strain relief for the connection cable). We recommend using motor protection switches with delayed switch off, depending on possible excess
current. Temporary excess current may occur
when the machine is started cold.
NOTICE
Power supply
The conditions at the installation location must match
the information on the motor data plate. Without
derating the following is permissible:
• ± 5% voltage deviation
• ± 2% Frequency deviation
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
17
Commissioning and decommissioning
6
Commissioning and decommissioning
6.1
Commissioning
WARNING
Improper use
May lead to severe or fatal injuries. Therefore be
sure to obey the safety instructions.
CAUTION
Noise emission
The highest noise pressure levels measured as
per EN ISO 3744 are given in Section 9.
When spending a long time in the vicinity of the
running machine use ear protectors to avoid permanent damage to your hearing.
NOTICE
Wait until the machine stops
The machine must only be switched on again
after it stops.
18
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Commissioning and decommissioning
6.1.1 Checking the rotation direction
The drive shaft direction of rotation is shown by
the rotation direction arrow (Fig. 3/O).
a) Start the motor briefly (max. two seconds) to
check the direction of rotation. When looking at
the motor fan, it must rotate clockwise.
The suction pipe must not be connected
when starting up like this.
NOTICE
Incorrect direction of rotation
Running the machine in reverse for a long time may
cause damage to the blades which may lead to the
blades breaking. Use a phase sequence indicator
to check the direction of rotation (anti-clockwise
rotating field).
6.2
Decommissioning/ storing
Stop the machine
a) Switch the machine off.
b) If available close the cut off device in the suction
and pressure pipe.
c) Disconnect the machine from the electricity
source.
d) Depressurise the machine: Open the pipes
slowly. The pressure reduces slowly.
e) Remove the pipes and hoses.
f)
Seal the connections for suction and discharge
nozzles with adhesive foil.
see also Section 3.2.1, Page 11
6.3
Re-commissioning
a) Check the condition of the machine (cleanliness,
cabling etc.).
For installation see Section 5 Page 15
For commissioning see Section 6.1 Page 18
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
19
Maintenance and repair
7
Maintenance and repair
DANGER
Danger of death from touching live parts.
Before maintenance work disconnect the machine
by pressing the main switch or unplugging it and
ensure that it cannot be turned on again.
WARNING
Hot surfaces and equipment
During maintenance work there is the danger of
getting burnt on hot components and by the machine lubricating oil.
Wait for the machine to cool down.
7.1
Ensuring operational safety
Regular maintenance work must be carried out in order to ensure operational safety.
Maintenance intervals also depend on the operational demands on the machine.
With any work observe the safety instructions described in Section 2.8 “Safety notes for installation, commissioning and maintenance”.
The whole unit should always be kept in a clean condition.
7.2
Maintenance work
Interval
Maintenance to be carried out
Section
monthly
Check the pipes and screws for leaks and to ensure they are
seated properly and if necessary seal again or tighten up.
—
monthly
Check the terminal box and cable inlet holes for leaks and if
necessary re-seal.
—
monthly
Clean the regulating valve and ventilation slots on the machine and the motor cooling ribs.
If there is a great deal of dust in the spaces on the cooling
ribs clean them.
—
—
The machine‘s bearings are permanently lubricated and do
not require re-lubricating.
—
monthly / every 6 months
Clean or replace filter cartridges
7.2.1
V-VTN 16:
V-VTN 26:
V-VTN 41:
Check blades
7.2.2
20
|
7,000 h / 1,000 h
5,000 h / 1,000 h
3,000 h / 1,000 h
Replace blades
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Maintenance and repair
7.2.1 Air filtering
s
b
G
s
Fig. 5 Air filtering
G
Outlet grid
b
Housing lid
e
Filterpatrone
m
Knurled knob
s
Screw cap
e
m
NOTICE
Insufficient maintenance on the air filter
The power of the machine lessens and damage may
occur to the machine.
The filter cartridge (Fig. 5/e) for suction air must be
cleaned by blowing through from the inside out once
a month or more often depending on the level of
contamination. In spite of cleaning the filters their
separation efficiency will continue to deteriorate.
Therefore the filters should be replaced every six
months.
Changing filters:
Unscrew the outlet grid (Fig. 5/G).
Undo the screw cap (Fig. 5/s) and the knurled knob
(Fig. 5/m). Remove and clean or replace filter cartridges (Fig. 5/e). Reassemble in reverse order.
WARNING
1
Danger of injury when dealing with compressed air.
When blowing through with compressed air, solid
particles may be carried along or powder dust swirling around may cause injury to the eyes. Therefore,
when cleaning with compressed air always wear
goggles and a dust mask.
2
Fig. 6 Purging filter cartridge
1
Filter cartridge
2
Compressed air
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
21
Maintenance and repair
7.2.2 Replacing blades
Y
Z
X
O1
b
d
Fig. 7 Changing blades
O1
Direction of rotation
X
Minimum height
Y
Slanting side of the blade
Z
Drilled holes in the housing
b
Housing lid
d
Blade
Checking blades:
V-VTN 16 / 26 have 6 carbon blades and V-VTN 41
has 7 carbon blades that wear out gradually during
operation.
V-VTN 16: First check after 7,000 operating hours,
then every 1,000 operating hours.
V-VTN 26: First check after 5,000 operating hours,
then every 1,000 operating hours.
V-VTN 41: First check after 3,000 operating hours,
then every 1,000 operating hours.
Unscrew the outlet grid (Fig. 5/G). Unscrew the
housing cover (Fig. 7/b) from the housing. Remove
the blades (Fig. 7/d) to be checked. All blades must
have a minimum height (Fig. 7/X):
Type
X (minimum height)
V-VTN 16, 26
24 mm
V-VTN 41
35 mm
The blades must only be changed as a set.
Changing blades: If you detect during the blade
check that the minimum height has been reached
or it has fallen below the minimum height, the blade
set must be changed.Blow out the housing and the
rotor slot. Insert the blades into the rotor slot. When
doing this you must ensure that the blades with
the sloping side (Fig. 7/Y) point outwards and the
direction of rotation of these sloping sides (Fig. 7/
O1) matches that of the drilled holes for the housing (Fig. 7/Z). Screw on the housing lidFig. 7/b) and
outlet grid (Fig. 6/G). Before starting up check that
the blades run freely by moving the fan round, for it
unscrew the inlet grating (Fig. 2/G1).
22
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Maintenance and repair
7.3
Reparatur/ Service
a) For on site repair work the motor must be
disconnected from the mains by a qualified
electrician so that it cannot be started up again
accidentally. For repairs use the manufacturer,
its branch offices or authorised dealers. Please
contact the manufacturer for the address of the
service centre responsible for you (see Manufacturer‘s address).
NOTICE
For each machine that is sent to an Elmo Rietschle Service centre for inspection, maintenance
or repair, a fully completed, signed declaration of
harmlessness must be enclosed.
The declaration of harmlessness is part of the
supplier‘s documentation.
b) After a repair or re-commissioning, the actions
listed under „Installation“ and „Commissioning“
must be carried out as for initial commissioning.
Fig. 8 Clearance certificate 7.7025.003.17
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
23
Maintenance and repair
7.4
Spare parts
Order spare parts in accordance with the:
•
Spare parts list:
E 281 ➝ V-VTN 16 - V-VTN 41
• Download the PDF file:
http://www.gd-elmorietschle.com
➝ Downloads
➝ Product Documents
➝ V-Series ➝ Spare Parts
• Parts subject to wear and gaskets are indicated separately on the list.
•
Web site:
http://www.service-er.de
• Select the type, size and design.
NOTICE
Fig. 9 Spare parts list (example)
Fig. 10
24
|
Only use original spare parts or parts approved by
the manufacturer. The use of other parts may lead to
malfunctions and invalidate liability or the guarantee
for any consequences arising.
Web site
http://www.service-er.de
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Malfunctions: Causes and elimination
8
Malfunctions: Causes and elimination
Fault
Cause
Troubleshooting
Important
Machine is switched
off by the motor protection switch
Mains voltage/ Frequency
does not correspond with the
motor data
Check by qualified electrician
Section 5.5
Connection to motor terminal
board is not correct
Motor protection switch is not
set correctly
Pumping capacity is
insufficient
Motor protection switch is
triggered too quickly
Use a motor protection switch
with an overload-dependent
delayed switch off that takes
into consideration the short
term excess current at start
up (version with short circuit
and overload trigger as per
VDE 0660 Part 2 orIEC 947-4)
The regulating valve is dirty so
that the permissible vacuum
value is exceeded.
Clean or replace the regulating valve
Section 7.2
Section 7.4
The intake filter is dirty
Clean or replace the intake
filter
Section 7.2.1
Section 7.4
The suction pipe is too long or
too narrow
Check the hose or the pipe
Section 5.3
Machine or system leaking
Check the pipework and
screw connections for leaks
and to ensure that they are
firmly seated.
Section 7.2
Blades are damaged
Replace blades
Section 7.2.2
Section 7.4
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
25
Malfunctions: Causes and elimination
Fault
Cause
Troubleshooting
Important
Final pressure (max.
vacuum) is not
reached
Machine or system leaking
Check the pipework and
screw connections for leaks
and to ensure that they are
firmly seated.
Section 7.2
Blades are worn or damaged
Replace blades
Section 7.2.2
Section 7.4
Ambient or intake temperature
is too high
Ensure it is being used properly
Section 2.3
Cooling air supply is obstructed
Check environmental conditions
Section 5.1
Clean ventilation slots
Section 7.2
The regulating valve is dirty so
that the permissible vacuum
value is exceeded.
Clean or replace the regulating valve
Section 7.2
Section 7.4
The compressor housing is
worn (chatter marks)
Repair by manufacturer or
authorised workshop
Elmo Rietschle
Service
The regulating valve is vibrating
Replace the valve
Section 7.4
Blades are damaged
Replace blades
Section 7.2.2
Section 7.4
Machine gets too hot
The machine makes
an abnormal noise
Please contact Elmo Rietschle Service for other malfunctions or those that cannot be eliminated.
26
|
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
Technical Data
9
Technical Data
V-VTN
Sound pressure level (max.)
EN ISO 3744
Tolerance± 3 dB(A)
Weight (max.)
Length
16
26
41
50 Hz
66
65
70
60 Hz
70
67
72
3~
26.8
30.7
46.7
1~
27.2
31.9
47.0
(01)
459
489
554
(02)
477
507
593
dB(A)
kg
mm
Width
mm
245
245
275
Height
mm
286
286
319
G 1 /2
G 1 /2
G 3/4
Vacuum connection
(01)
(02)
Standard version with vacuum safety valve
Version with vacuum regulating valve
You will find more technical data on the data sheet
D 281
•
Download the PDF file
D 281 ➝ V-VTN 16 - V-VTN 41
• Download the PDF:
http://www.gd-elmorietschle.com
➝ Downloads
➝ Product Documents
➝ V-Series ➝ Data Sheets
NOTICE
Subject to technical changes.
Fig. 11 Data sheet (example)
www.gd-elmorietschle.com © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH
|
27
www.gd-elmorietschle.com
[email protected]
Gardner Denver
Schopfheim GmbH
Roggenbachstraße 58
79650 Schopfheim · Deutschland
Tel. +49 7622 392-0
Fax +49 7622 392-300
Elmo Rietschle is a brand of
Gardner Denver‘s Industrial Products
Division and part of Blower Operations.
EC - declaration of conformity 2006/42/EC
Hereby the manufacturer
confirms:
Gardner Denver Schopfheim GmbH
Postfach 1260
D-79642 Schopfheim
that the machine:
of the:
Dry running vacuum pump
Series:
V-VTN
Type:
V-VTN 6, V-VTN 10, V-VTN 15,
V-VTN 25, V-VTN 40, V-VTN 60
V-VTN 16, V-VTN 26, V-VTN 41
Is conform to the regulations of the guideline indicated above.
The following harmonized and national standards and specifications are applied:
EN 1012-1:2010
Compressors and vacuum pumps — Safety requirements — Part 1:
Compressors
EN 1012-2:1996+A1:2009 Compressors and vacuum pumps — Safety requirements — Part 2:
Vacuum pumps
These declarations of conformity are invalid when the machine has been modified without prior approval by us and the approval has been documented in writing.
Name and address of the EC person in
charge for documentation
Gardner Denver Schopfheim GmbH
Postfach 1260
D-79642 Schopfheim
Gardner Denver Schopfheim GmbH
Schopfheim, 01.8.2011
Dr. Friedrich Justen, Director Engineering
C_0083_EN
Safety declaration form
for vacuum pumps and components
7.7025.003.17
Page 1 of 1
Gardner Denver Schopfheim GmbH
Roggenbachstr. 58, 79650 Schopfheim
Phone: +49/(0)7622/392-0
Fax: +49/(0)7622/392-300
Repairs and/or maintenance of vacuum pumps and components will only be carried out if a declaration has been
filled in correctly and completely.
If not, the repair work cannot be started and delays will result.
This declaration must only be filled in and signed by authorised qualified staff.
1. Type of vacuum pumps/ components
2. Reason for the submission
Type description:
Machine number
Order number:
Delivery date:
3. Condition of vacuum pumps/ components
YES ‰
NO ‰
4. Contamination of the vacuum pumps/
components when in use
Toxic
YES ‰ NO
Corrosive
YES ‰ NO
Was the pump/ component emptied?
Microbiological*)
YES ‰ NO
(Product/Consumables)
YES ‰
NO ‰
Explosive*)
YES ‰ NO
Has the pump/ component been cleaned and decontaminaRadioactive*)
YES ‰ NO
other
YES ‰ NO
YES ‰
Was this being operated?
Which lubrication was used?
‰
‰
‰
‰
‰
‰
Cleaning agent:
Cleaning method:
*) Microbiological, explosive or radioactively contaminated vacuum pumps/ components will only be accepted
with proof that they have been cleaned properly.
Type of toxic substance or process-related, dangerous reaction products with which the vacuum pumps/
components came into contact:
Trade name, manufacturer's
product name
1
2
3
4
Chemical
name
Hazard
class
Action to be taken if toxic
substances are released
First aid in the event of
accidents
Personal protection measures:
YES
Hazardous decomposition products when subjected to thermal load
‰
NO
‰
Which?
5. Legally binding declaration
We swear that the information in this declaration is accurate and complete and that I, the undersigned, am in a
position to judge this. We are aware that we are liable to the contractor for damage caused by incomplete and
inaccurate information. We undertake to release the contractor from any damage claims from third parties arising
from incomplete or incorrect information. We are aware that, regardless of this declaration, we are directly liable
to third parties including in particular the contractor's staff entrusted with handling or repairing the product.
Company:
Street:
Post code/ Town:
Phone:
Fax:
Name (in capitals)
Date:
Position:
Company stamp:
Legally binding signature:
TOS no. / Index: 7.7025.003.17 / 03
Office responsible: GS
File management: ..\7702500317.xl
Gardner Denver Schopfheim GmbH Postfach 1260 D-79642 Schopfheim

advertisement

Key Features

  • Dry running rotary vane vacuum pump
  • Suitable for evacuating closed systems
  • Permanent vacuum in the intake pressure range 150 - 1000 mbars (abs.)
  • Pumping capacity with unrestricted suction is 15, 25 and 40 m3/h at 50 Hz
  • V-VTN 16, V-VTN 26 and V-VTN 41 models available

Frequently Answers and Questions

What is the intended use of the V-VTN vacuum pumps?
The V-VTN models are designed for evacuating closed systems and creating a permanent vacuum within a specific intake pressure range.
What is the pumping capacity of the V-VTN vacuum pumps?
The pumping capacity varies depending on the model and frequency. For example, at 50 Hz, V-VTN 16 has a capacity of 15 m3/h, V-VTN 26 has 25 m3/h, and V-VTN 41 has 40 m3/h.
What is the intake pressure range for the V-VTN vacuum pumps?
The V-VTN models can operate in the intake pressure range of 150 to 1000 mbars (absolute pressure).

Related manuals

Download PDF

advertisement