Meridian DSW Earlier Product User guide

DSW
User Guide
EN
DSW User Guide
Important safety instructions
•
•
•
•
•
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
This apparatus has been designed with Class 1 construction and
must be connected to a mains socket outlet with a protective earthing
connection (the third grounding pin).
This apparatus does not include a power switch. The apparatus may be
isolated from mains power either by unplugging the power connector from
the rear of the unit, or by unplugging the connector at the opposing end
of the power cord or cable from its supply outlet. As a result, either or
both of these connectors should remain accessible
Safety warnings
• Do not expose the unit to dripping or splashing.
• Do not place any object filled with liquid, such as a vase, on the unit.
• Do not place naked flame sources, such as lighted candles, on
the unit.
• To avoid overheating leave at least 10cm around the equipment to
ensure sufficient ventilation.
• Do not position the unit in direct sunlight, near heat sources such as
a radiator, or directly on top of heat producing equipment, such as a
power amplifier.
• To avoid interference do not position the unit near strong electrical or
magnetic radiation, such as near a power amplifier.
Radio interference
FCC Warning: This equipment generates and can radiate radio
frequency energy and if not installed and used correctly in accordance
with our instructions may cause interference to radio communications
or radio and television reception. It has been type-tested and complies
with the limits set out in Subpart J, Part 15 of FCC rules for a Class
B computing device. These limits are intended to provide reasonable
protection against such interference in home installations.
EEC: This product has been designed and type-tested to comply
with the limits set out in EN55013 and EN55020.
Copyright
Meridian Audio Ltd
Latham Road
Huntingdon
Cambridgeshire
PE29 6YE
England
Copyright © 2011 Meridian Audio Ltd.
Visit us on the Web:
http://www.meridian-audio.com
Part no: DSW (P88397)
This guide was produced by: Human-Computer Interface Ltd,
http://www.interface.co.uk/
EN
DSW User Guide
Unpacking
The DSW is supplied with the following accessories:
If any of these items are missing please contact your dealer.
• Power cord.
• Three rubber inserts.
• This manual.
NOTE: You should retain the packaging in case you need to
transport the unit.
Connections
Digital connections
The following diagram gives details of the connections on
the back of the subwoofer:
Use this connection
To connect to this
SpeakerLink input
The SpeakerLink output of a Meridian
Digital Surround Controller or Audio
Core 200, or the SpeakerLink output of
another DSP loudspeaker.
SpeakerLink output
The SpeakerLink input of a second
DSW digital subwoofer, when daisychaining the speakers.
SpeakerLink
input output
Power Fuse
Output
Input
Power Inlet
Digital Channel
Selector
1
1+2
2
SpeakerLink
Channel
selector
Miscellaneous
Switch
Description
Digital Channel Selector
Set to 2 to use as an LFE/mono sub­
woofer with a Digital Surround Controller.
Set to 1+2 to use with an Audio Core
200. Set the left subwoofer to 1 and
the right subwoofer to 2 to use two sub­
woofers with a Digital Surround Controller.
Standby indicator
Fitting the rubber inserts
The status of the DSW is shown by a green standby indicator
on the back panel.
As supplied, the feet are suitable for soft, carpeted surfaces.
To use the DSW on a hard surface insert one of the supplied
self-adhesive rubber inserts into the recess on each foot:
Status
Description
Dimly illuminated
Speaker in standby
Brightly illuminated
Speaker operating
The subwoofer is switched on or into standby as appropriate
via the SpeakerLink connection by the Meridian system it is
connected to.
DSW User Guide
EN
Applications
To connect a pair of DSP3200s and a DSW to
a Meridian Audio Core 200
• Connect the upper SpeakerLink output on the Audio Core
200 to the SpeakerLink input of the DSW subwoofer, using a
Meridian SpeakerLink lead.
The DSW is ideal in combination with a pair of DSP3200 or
DSP3300 loudspeakers to create a compact Audio Core 200
based system.
• Connect the SpeakerLink output from the DSW subwoofer to
the Slave DSP3200, using a Meridian SpeakerLink lead.
• Set the Channel selector to the L/C position on the left
speaker, to the R position on the right speaker, and to the
1+2 position on the DSW subwoofer.
• Connect the lower SpeakerLink output on the Audio Core
200 to the SpeakerLink input of the Master DSP3200, using
a Meridian SpeakerLink lead.
Meridian Audio Core 200
SPEAKERLINK
IN
OUT
DSP3200 – Slave
DSW – Subwoofer
DSP3200 – Master
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
INPUT OUTPUT
INPUT OUTPUT
SpeakerLink lead
SpeakerLink
lead
SpeakerLink lead
DSW User Guide
EN
To use a DSW as the subwoofer in a Meridian
Digital Theatre
The DSW is ideal as the subwoofer in a Meridian Digital
Theatre, in combination with DSP3200 or DSP3300 front and
rear loudspeakers and a DSP3300 centre speaker. The system
can be controlled by a Meridian Digital Surround Controller such
as the G68. The following diagram shows how to connect the
speakers using “home run” wiring.
• Connect the L+R SpeakerLink output on the lower row of
the G68 to the Master digital speaker (here the front left
speaker), using a Meridian SpeakerLink lead.
• Connect the appropriate SpeakerLink outputs on the G68
to each of the remaining speakers and the subwoofer, using
Meridian SpeakerLink leads.
• Set the Channel selector on the front and rear left speakers
to the L/C position, and on the front and rear right speakers
to the R position.
• Set the Channel selector on the centre speaker to the L/C
position, and on the DSW subwoofer to the 2 position.
Alternatively you can connect the speakers using “daisy chain”
wiring: connect the front and rear L speakers to the G68,
and then link each pair of speakers together by connecting
the output from the L speaker to the input of the R speaker.
Likewise connect the centre speaker to the G68, and then
link the output from the centre speaker to the input of the
subwoofer.
Note that if the system includes DSP loudspeakers with
displays, such as the DSP5200, one of them must be set up as
the master in the system.
Meridian Surround Controller
DSP3200 – Rear R
DSP3200 – Rear L
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
INPUT OUTPUT
SpeakerLink
SpeakerLink
DSP3200 – Front R
DSP3300 – Centre
DSW – Subwoofer
DSP3200 – Front L (Master)
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
INPUT OUTPUT
INPUT OUTPUT
INPUT OUTPUT
SpeakerLink
SpeakerLink
SpeakerLink
SpeakerLink
DSW User Guide
EN
EN
DSW User Guide
DSW User Guide
EN