Robot Mower TC-G158 Owner Manual
Robot Mower TC-G158: Experience the future of lawn care with our intelligent robotic lawn mower. Equipped with advanced sensors, it navigates your lawn efficiently, avoiding obstacles and adjusting its mowing pattern to achieve a precise and manicured finish.
Advertisement
Advertisement
ROBOT MOWER
USER MANUAL
Please read this manual before use
Please keep this manual for future reference
ROHS
The products are manufactured by Taizhou Tianchen Intelligence &
Electrics Co., Ltd.
www.tianchen-cn.com
Thank you for purchasing our product. We know that you will enjoy the extra free time you will have while using our robot lawn mower to mow your lawn. You will be impressed with your lawn's appearance and vest of all, robot lawn mower did it for you.
IMPORTANT
!
The following pages contain important safety and operating instructions.
Please read and follow and instructions in this manual. Carefully read and review all safety instructions, warnings and cautions contained in this manual.
Failure to read and follow these instructions, warnings and cautions statements may result in severe injury or death to persons and pets or damage to personal property.
WARNING
Robot lawn mower can be dangerous if incorrectly used
!
CONTENTS
1. INTRODUCTION AND SAFETY······················································P1
1.1 Introduction P1
1.2 Symbols on mower P2
1.3 Symbols in the User Manual P3
1.4 Safety instructions P4
2. PRESENTATION··········································································P6
2.1 What's in box P6
2.2 Functions P8
2.3 Technical data P10
2.4 Working route P12
3. INSTALLATION···········································································P13
3.1 Preparations P13
3.2 Hardware adjustments P13
3.3 Charging station installation P15
3.4 Virtual wire installation P17
3.5 Virtual wire and charging station connecting P23
3.6 Power connection P23
4. REMOTE CONTROL·························· ·································· ·······P24
4.1 Remote control P24
5. USE····················································································P25
5.1 Preparation P25
5.2 Starting the mower P26
5.3 Stopping mower /Turn off mower P27
5.4 Emergency Switch P27
5.5 Recharging P27
6. MAINTENANCE AND STORAGE··············································P29
6.1 Robot cleaning P29
6.2 Robot Storage P31
6.3 Blade replacement P31
6.4 Battery P32
7. TROUBLE SHOOTING····························································P33
8. EXPLODED VIEW··································································P38
8.1 Charging station Exploded View P38
8.2 Mower Exploded View P39
1.INTRODUCTION AND SAFETY
1. Introduction and safety
1.1 Introduction
Product, product specifications and this document are subject to change without notice. All other trademarks are property of their respective owners.
The lawn mower may be used only by those who know how to operate it after reading and understanding the instructions in this manual.
Model: TC-G158
CE, RoHS approved.
The following pages contain important safety and operating instructions.
Please read and follow all instructions in this manual. Carefully read and review all safety instructions, warnings and cautions contained in this manual.
Failure to read and follow these instructions, warnings and cautionary statements may result in severe injury or death to persons and pets or damage to personal property.
IMPORTANT INFORMATION
Read through the Operators Manual carefully and understand the content before
WARNING
Robot lawn mower can be dangerous if incorrectly used.
-
P1
-
1.INTRODUCTION AND SAFETY
1.2 Symbols on mower
These symbols can be found in the mower. Study them carefully so you understand their significance.
1. The symbol is pasted on the top of mower, please read it carefully
before using the appliance.
2. Specifications symbol
Taizhou Tianchen Intelligence &Electrics Co,Ltd
Taizhou Tianchen Intelligence &Electrics Co,Ltd
Product name: Robot lawn mower
Product name: Robot lawn mower
Input: 24 V 2A
85
W
Input: XXX V --- 2A 85W
R
O
HS
Pasted on mower
Taizhou Tianchen Intelligence &Electrics Co,Ltd
Product name: Robot lawn mower
Model: Indream 10900 IPX1
Input: 24 V 2A
Ouput :24V 2A
Made in China
Address
:XX
R
O
HS
2011
Pasted on charging station
ADDRESS
:
XX
The factory has set the address already, which is to match
the communicate between charging station and mower.
S.N.: XXXX XX XX XXX year month date number
: Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.
-
P2
-
1.INTRODUCTION AND SAFETY
3. Charging station symbol.
This label is pasted on charging station, please make sure to position this side towards lawn interior. Failure to do may result
in damage to property or persons.
4. Warning symbol.
DANGER! Sharp rotating blades.
Keep hands and feet away. Serious
injury can occur.
Position his side of the charging
station towards lawn interior
DANGER
1.3 Symbols in the User Manual
These symbols can be found in this owner/operating manual. Study them carefully so you understand their significance.
WARNING
xxxxxxxxxxxxxxxxxxxxxxxxx.
A warning box indicates a risk of personal injury exist, especially when the stated instructions are not followed.
IMPORTANT INFORMATION
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx.
An information box indicates a risk of material damage exist, especially when the stated instructions are not followed. The box is also used where there is a risk of user error.
-
P3
-
1.INTRODUCTION AND SAFETY
1.4 Safety instructions
- Read the owners/operation manual carefully and follow all the safety
and warning instructions.
- This machine has sharp rotation blades! Never allow the mower to
operate unattended; keep bystanders, children and pets away from
mower when in operation.
- Never allow anyone to ride or ait on mower.
- Never allow anyone or person who is not familiar with the safe operation
of the mower to operate the mower.
- Keep hands and feet away from the cutting blades and other moving
parts.
- Never attempt to service or adjust the mower while it is in operation.
- Inspect and clear the mowing area of all debris (toys, tree branches,
items of clothing, debris' height less than 6cm. etc) before operating the
mower.
- Never raise the mower or attempt to inspect the blades while the mower
is operating.
- Always turn off the power before lifting the mower or attempting any
adjustment.
- When operating the mower in manual mode, maintain a safe distance
from behind or around the mower and wear proper foot apparel.
- Do not operate the mower on slopes greater than 20 degrees or use it in
manual operation on slopes where a firm footing is not possible.
- Do not operate the mower if any safety feature or device is damaged or
inoperable.
- Do not attempt to disable or defeat any safety feature or device.
-
P4
-
1.INTRODUCTION AND SAFETY
- Use heavy gloves when inspecting or servicing the blades.
- Wear eye protection and use gloves when installing the virtual wire and
driving the wire stakes/pegs. Firmly drive all pegs in order to keep the
wire from becoming a tripping hazard.
- Do not use the charging station power supply with an extension cord.
- Use only the original equipment power pack and power supply/charger
with this mower.
- Do not use the power supply/charger if the cord has become damaged.
- Do not place metal objects in the area of the charging contacts on the
charging station.
- Do not place metal objects across the charging pins of the mower.
- Do no spray water directly into the docking area of the charging station
or onto the operating panel of the charging station.
- The mower has sharp rotating blades! Please care the mower when it is
mowing, in case of serious injury occur.
- Keep the lawn mower in perfect operating conditions by performing the
maintenance procedures outlined by the manufacturer. Good
maintenance
guarantees better performance and longer service life.
- In order not to irreversibly damage electric and electronic parts, do not
wash the robot with water jets at a high pressure and do not plunge it
partially or thoroughly in water, as it is not watertight.
- It is absolutely forbidden to use the robot in explosive and flammable
environments.
- The operator or user is responsible for accidents or hazards occurring to
other people or their property.
-
P5
-
2. PRESENTATION
2. Presentation
This chapter contains information you should be aware of when planning the instalation.
2.1 What's in box
1
2
3 2
3
2 4 5
6
7
8
9
10
11
22
23 2 4
25 2 6
12
13
17
18
14
15
20
16
19
21
2 7 28 29 30
-
P6
-
2. PRESENTATION
1
2
Handle:
Bumper:
To change a new direction when it bump obstacles.
Charging point
16
17
Charging light
Red: charging
Green: fully charged or idle
Charge terminal
3
4
Emergency switch:
Press it at any time, the mower turn off at once.
18
Virtual wire terminal
19
Connect the virtual wire randomly.
there is no positive and negative.
Charging sheet
5
6
7
8
10
11
12
13
Charging terminal: 20
Connect with charger for recharge
21 directly.
22
Rain sensors:
Mower goes back to charging station automatically when it rains.
Power light
Key switch:
on
off
Guide channel
Stakes hole
Charger
Used for directing the mower to charging station or for recharge directly.
23
Virtual wire / 100m
Used to mark mowing area and create a virtual wall for the mower.
24 Remote control
Omni-directional wheel
Blade
Safety hence:
To keep off foot and hands
Handle
Blade shed
25
2 6
Pegs / 100pcs
Used for fix the virtual wire to the ground around the lawn perimeter and around obstacles.
Stakes / 4pcs
Used for fix the charging station to ground.
14
15
Tyre cover:
Take it out and change the wheel.
Virtual wire light
Red: broken wire/idle
Colorless: good wire connecting
2 7
28
Blades
Two blades pre-installed on the mower and two extra.
Key / 2pcs
29
30
Remote control battery
English user maual
Consumable parts
1. Blade
2. Virtual wire
3. Pegs
-
P7
-
2. PRESENTATION
2.2 Functions
- Lift sensor
There are lift sensors located on each omni-directional wheel. If the
mower was lifted 2cm from the ground in level way, it will stop working
within 2 seconds.
- Tilt sensor
There is tilt sensor installed on the mower too, when the mower was
tilted over 30 degree at any direction, it also will stop working within 2
seconds.
- Bump sensors
In front of the mower there equipped with bump sensors that will activate
when the mower strikes solid, fixed object when that object is at least
6.5cm in vertical height from the supporting surface of the mower. When
the bump sensor is activated, the mower will stop movement in that
direction and reverse itself away from the obstacle.
- Rain sensors
There are two rain sensors on top cover of mower. The mower will go back
to the charging station automatically when it's raining.
- Wireless controller
To control the operate of mower in manual pattern.
- Anti-theft function
The mower should be turned on by key. And it can’t start working without
a matched charging station.
- Virtual wire
The robot lawn mower can't operate without a virtual wire. (we suggest to
use 100m-300m of virtual wire). It leads the mower back to charging
station and the mower will take it as a wall when it is operating. It will gets
on the virtual wire until it meets charging sheet which located in front of
charging station, then it gets off virtual wire and starts cutting
- Cutting height selection
There are two choice, 3cm and 4cm.
-
P8
-
2. PRESENTATION
- Cutting width:28cm
- Auto recharge system
When the mower is operating it feels powerless, the cutting motor turn off
at once and it will find the virtual wire then go alone it back to charging
station for recharge automatically. (this allows you to keep the charger
connected with the charging station all the time, even after the battery is
fully charged.) On auto pattern, the mower will go on mowing after fully
recharge. But if it is on manual pattern, it will just stay on charging station
after fully recharged.
- Emergency stop switch
There is an emergency stop switch located on the back of mower and red
in color. If you press it in any case during operating, the mower must stop
all movement and stop the rotating of blades immediately. Rotating the
switch to reset it.
- Two cutting modes
There are two cutting modes of the mower, go straight and go circle (high
efficiency). Go circle only effect on Auto pattern.
- Overload protect
Each of the two blade motors and each of the two wheel driving motors
are monitored continuously during operation for any situation that may
cause these motors to over-load. In the event this is detected, the mower
will stop operating.
- Three steps to safe start the appliance
Three necessary steps to start the mower: firstly, connect virtual wire to
charging station and make sure it is in good connecting (virtual wire light
on charging station is colorless). Second, connect charging station with
power supply through charger and the charging station light is in green
color. Third, turn on the power of mower by key and choose operating
pattern from remote control. The mower start working.
-
P9
-
2. PRESENTATION
2.3 Technical data
Model
Mower technical data
Gross weight
Net weight
Mower size
TC-G158 with lead-acid
21KGS
18.5KGS
56*51*25cm(LWH)
TC-G158 with lithium
18.5KGS
16KGS
56*51*25cm(LWH)
Power
Noise
Qty for cutting blades
85W
≤
65db
2pc
85W
≤
65db
2pc
Cutting height
Cutting width
3cm, 4cm
28cm
3cm, 4cm
28cm
Cutting speed
Blades rotate speed
20m/min
5000rpm
Hill capability
Max ambient functioning temp.
30degree Ma xslope
40
℃
Co verage(for once charging)
600m2+20
％
Working capacity 1500m2+20
％
20m/min
5000rpm
30 de gree Max sl op e
40
℃
600m2+20
％
1500m2+20
％
Warranty
1 year
1 year
PS:
How large an area is mown per once recharge depends primarily on the condition of the blade and the type of grass, growth rate and humidity. The shape of garden is also significant. If the garden mainly consists of open lawns, mower can mow more per hour than if the garden consists of several small lawns separated by trees, flower beds and passages.
Charging station and virtual wire
Charging station size
38.5*44.5*16cm(L W H)
Virtual wire maximum length
Standard virtu al wire length
200m
100m
38.5*44.5*16cm(L W H)
200m
100m
-
P10
-
2. PRESENTATION
Model
Battery
Type of battery battery
Charging time
Average working time
Functions:
Around virtual wire walking option
Mower can’t be started when charging station is powerless
Mower can’t be started when virtual wire has be cut
Intelligent lawn testing
Rain sensor
Auto recharge
Intelligent spiral
Go straight
Anti theft
Lift sensor
Tilt sensor
Ultrasonic wave
Bumper sensor
LED display
Waterproof
Human sensor
Time set-up system
Emergency switch set up password
Rain sensor option
Around virtual wire option
10900
Lead-acid battery
7.2Ah
3-4hours
2-3hours
X
X
X
X
X
-
P11
-
X
X
X
11000
Lithium battery
7.2Ah
4.5hours
2-3hours
X
X
X
X
X
X
X
X
2. PRESENTATION
2.4 Working route
Manual pattern
Mower's running path by user's willingness.
IMPORTANT INFORMATION
User turn on the mower and select Manual pattern,
The mower will not going to find the virtual wire .
Auto pattern
Cutting route when Line is turned on.
-
P12
-
3. INSTALLATION
3. Installation
This chapter describes how you install this mower. Before starting the installation read the previous chapter 2. Presentation.
Read the whole of this chapter too before starting the installation. How the installation is made also affects how well the mower will work. It is therefore important to plan the installation carefully.
3.1 Preparations
Training
- Read the instructions carefully. Be familiar with the controls and the
proper use of the appliance.
- Never allow people unfamiliar with these instructions or children to use
the appliance. Local regulations may restrict the age of the operator.
- The operator or user is responsible for accidents or hazards occurring
to other people or their property.
3.2 Hardware adjustments
Blade adjustment
The mowing system used by this mower is based on an effective and energy efficient principle. Unlike normal lawn mowers, the mower cuts the grass instead of striking it off.
We recommend you allow the mower to mainly mow in dry wether to obtain the best possible result.
The blades must be in good condition to obtain the best mowing result. In order to keep the blade sharp for as long as possible it is important to keep the lawn free from branches, small stones and other objects
(especially the objects less than 6.5cm height).
-
P13
-
3. INSTALLATION
How to adjust the cutting height:
- The cutting height can be varied for
3cm and 4cm. (Factory setting of
blades is 4cm)
If the grass is long, it is appropriate
to let the mower start mowing at 4cm.
Once the grass is shorter. you
can change it lower with 3cm.
- To adjust the cutting height:
1. Stop the mower and take off the
key.
2. Turn over the mower to underside.
It’s easy to find that there are two
blades fix on the blades holder.
Swing the 4 screws on blades
holder. And take blades out.
3. There are two levels on the Blades
Holder, level 3cm and level 4cm.
4. Choose your cutting height (3cm or
4cm), and then fix the two blades
with screws.
5. Turn over the mower to upside.
Cutting height adjustment finished.
Blade holder
Level 4cm
Level 3cm
Cut ting he igh t: 3c m
Cutting height explanation:
For example the cutting height is in 3cm level.
Grass
Height
-
P14
-
3. INSTALLATION
3.3 Charging station installation
- Choose best installation place, please make sure which is flat, no water,
no magnetic interference and no obstacle in the front of charging
station.
3. INSTALLATION
- Lay virtual wire in the middle of
charging station.
Virtual wire
- Fix the charging station with four
stakes.
Charging station best install place
:
1. Make sure it
2. No magnetic interference
3. No water
4. No obstacle in front
- Please fix the charging station in level place.
IMPORTANT INFORMATION
Before fix the charging station on the lawn, please examine the lawn and decide the best location which is easy for the mower to find the station for recharge.
Peg
-
P15
-
P16
-
3. INSTALLATION
3.4 Virtual wire installation
The virtual wire can be installed in one of the following ways:
- Securing the wire to the ground with pegs.
It is preferable to staple down the virtual wire, if you want to make
adjustments to the virtual wire during the first few weeks of operation.
- Bury the wire
It is preferable to bury the virtual wire if you want to dethatch or aerate
the lawn.
If necessary both methods can be combined so one part of the virtual
wire is stapled down and the remainder is buried.
- Dig virtual wire with pegs 1 meter per piece in straight-line. Dig corner as
picture.
OK
- Bury virtual wire below grass and fasten it on the ground with pegs, so
that the mower should not cut the wire. If the grass grow up, we can still
keep the virtual wire as before.
virtual wire
Add pegs in order to pull the virtual wire down to the ground surface, below the grass tips.
IMPORTANT INFORMATION
Hard or dry ground may cause pegs to break when driving them in.
In extreme cases, watering the lawn where the pegs will be driven.
-
P17
-
3. INSTALLATION
- A minimum distances of front charging station and obstacle is 2 meters.
And make sure the distance from corner to front of charging station is at
least 2.5 meters. Make sure to lay a 2.5 meters minimum straight-light of
virtual wire in front of charging station.
IMPORTANT INFORMATION
The charging station is not water-proof,
It’s best to make a Rain Shed above the charging station.
-
P18
-
3. INSTALLATION
- If a high obstacle, for example a wall or fence, borders the working area,
the virtual wire should be laid at least 35cm from the obstacle. This will
prevent mower from colliding with the obstacle and reduce body wear.
Greater than
35cm
3. INSTALLATION
- The wires leading to the island and
returning from it should be parallel
and touding. But do not cross them!
If protected obstacles are grouped
closely together demarcate them by
a single. Continuous virtual island if
obstacles are dose to edge, leave
them out of the mowing area.
- The distance between charging station and virtual loop should at least
2.5 meters.
- Use the virtual to demarcate areas inside the working area by creating
islands around obstacles that can not withstand a collision, for example,
flower beds and fountains. Run the cable out to the area, route it around
the area to be demarcated and then back along the same route. If
staples are used, the wire should be laid under the same staple on the
return route. When the virtual wire to and from the island are close
together, the mower can drive over the wire.
Max: 1cm
Max: 1cm
35cm
Max: 1cm
Virtual wire
-
P19
-
Virtual wire
Root
Max:20cm
1cm
Greater than 2.5 m
Tree with hole or flowers around require placing a wire around it
-
P20
-
1cm
3. INSTALLATION
- How to set virtual wire on the ground which has swimming pool.
Distance between two wire: 1m
Greater than
35cm
Rain shed
45
°
IMPORTANT INFORMATION
The charging station and charger is not water proof. It’s best to set a Rain Shed above the charging station.
-
P21
-
3. INSTALLATION
- Care must be taken not to create a corner sharper shorter than 90
degrees when setting up virtual wire. A corner sharper less than 90
degrees can cause the mower to lose track of virtual wire. We can make
greater than 90 degrees corner like follow picture shows.
Incorrect corner
setup
Greater than
2.5m
Correct corner set up, using several angle to avoid an angle of less than 90
°。
Proper setup in sharp corners
- Joining the boundary wire .
If the boundary wire is not long enough
and needs to be spliced: Use original
solderless couper. It is waterproof and
gives a reliable electrical connection.
To splice: Insert both cable ends in the
coupler. Now press down the button on
top of the connector fully. Use a pair of
pliers or the like, as the button on the
connector is difficult to press down by
hand
-
P22
-
3. INSTALLATION
3.5 Virtual wire and charging station connecting
- Connect two ends of virtual wire to
patch jack (virtual wire terminal
located on charging station)
randomly, there is no positive and
negative.
- Redundant virtual wire must be cut.
3.6 Power connection
1. Insert charger to the station. 2. Connect charger with power
supplier.
220V/110V
power supplier
4. REMOTE CONTROL
4.1 Remote control
mower enters taskstate.
9
1
4
Press it during mower is working,
it goes back to charging station.
8
User has to stop the mower first,
then press it, the mower enters
MANUAL pattern.
User has to stop the mower first,
then press it, the mower enters
AUTO pattern.
7
Turn ON/OFF blade.
7
6
2
5
4
IMPORTANT INFORMATION
3 8 9
These Three buttons only effected in MANUAL pattern.
WAR NI NG
Th e cha rge r is no t wat er -pr oo f the ref or e it mus t be loc at ed on a pl ac e whi ch is dr y an d ven tilat ed .
-
P23
-
P24
-
5
.
USE
5. Use
IMPORTANT INFORMATION
Operation with Auto Pattern
- Do not leave the machine to operate unattended if you know that there
are pets, children or people in the vicinity
Operation with Manual Pattern
- Mow only in daylight or in good artificial light.
- Avoid operating the appliance in wet grass.
- Do not operate the appliance when barefoot or wearing open sandals.
- Always wear substantial footwear and long trousers.
- Always be sure of your footing on slopes.
- Use extreme caution when reversing the appliance towards you.
- Always switch on the mower according to instructions with feet well
away
from the blade.
WARNIN
Read the safety instructions before you start your mower.
WA R N I N
Keep your hands and feet away from the rotating blade.
Never put your hands or feet close to or under the body when
the motors are running
.
5.1 Preparation
- Ensure the correct installation of the virtual wire delineation system as
instructed
- Periodically inspect the area where the appliance is to be used and remove all stones
, sticks, wires, bones, and other foreign
objects especial the objects
' height is less than 6cm.
- Periodically visually inspect to see that the blades
, blade bolts and
cutter assembly are not worn or damaged. Replace worn or damaged.
-
P25
-
5
.
USE
blades and bolts in sets to preserve balance.
- On multi-spindle appliances
, take care as rotating one blade can
cause other blades to rotate
- Connect two terminals of virtual wire to charging station, and ensure
virtual wire is in good connecting. (Light on charging station is in
colorless).
- Insert charger to charging station and screw it.
And then connect
charger to power supplier
.
Ensure charging station is in good
connecting
, light on charging station is in Green
.
IMPORTANT INFORMATION
User can
' t start the mower if virtual wire and charging station has problem.
5.2 Starting the mower
Start point
1.Take the mower to start point.
2. Turn the key switch on.
3. Clockwise rotate Emergency switch,
4. Select operate pattern (Auto pattern
or Manual pattern) from Remote
control.
5. The mower start.
-
P26
-
5
.
USE
5.3 Stopping mower /Turn off mower
1.
Press power button from remote control
.
Mower stops, the blade motor stops.
mower goes into taskstate.
2. The appliance also can be turned off by
press emergency switch directly.
3. Turn off the mower by anti-clockwise
the key switch.
5.4 Emergency Switch
Press emergency switch at any time the mower power off at once. User has to restart the appliance.
5.5 Recharging
Recharge Voltage:24V (Lead-acid battery) / 29.4V(Lithium battery)
Recharge current: 2A
- The mower could goes back to recharging automatically if it is power
less. Or press the Home button from remote control, the mower also
could goes back to station for recharge.
- The mower also can recharges by charger directly.
-
P27
-
5
.
USE
Steps as follow:
1. Turn off the mower by key.
2. Insert charger and screw the
Knob.
3. Connect the charger to power
supplier.
4. Connect the charger to power
supplier.
WA R N I N
The charger is not water-proof therefore it must be located on a place which is dry and ventilated.
-
P28
-
6. MAINTENANCE AND STORAGE
6
.
Maintenance and storage
- During maintenance operations, use the individual protections indicated
by the Manufacturer , especially when intervening on the blade.
- Before performing maintenance operations, make sure that the robot
has stopped in safety conditions.
PROGRAMMED MAINTENANCE INTERVALS CHART
Frequency Component Reference
Every week
Blade
Type of operation
Clean and check the efficiency of the blade
If the blade is bent due to an impact or if it is worn-out, replace it.
See “Robot cleaning”
See “Blade replacement”
Every month
Robot Carry out cleaning
See “Robot cleaning”
6.1 Robot cleaning
1.Stop the robot in safety conditions.
2. Wear protective gloves.
-
P29
-
6. MAINTENANCE AND STORAGE
3.Clean all the outside surfaces of the robot with a spong soaked in warm water
.
4.Do not use solvents or benzene so not to damage the varnished surfaces and the plastic components.
5.Do not wash the inside parts of the robot and do not use water jets in
pressure so not to damage the electric and the electronic
components.
WARNING
Never use a high-pressure washer or even running water to clean the robot.
6.Check the lower part of the robot (cutting blade area and wheels)
and remove the deposits and/or residues that might obstruct the
correct functioning of the robot.
7. To remove the deposits and/or other residues from the blade, use a
suitable brush.
8. Clean the outside of the charging station from any accumulated
residues.
9. Keep all nuts, bolts and screws tight to be sure the appliance is in
safe working condition.
10. Replace worn or damaged parts for safety.
11. Ensure that only replacement cutting means of the right type are
used.
12. Ensure that batteries are charged using the correct charger
recommended by the manufacturer.
13.Incorrect use may result in electric shock, overheating or leakage
of corrosive liquid from the battery.
-
P30
-
6. MAINTENANCE AND STORAGE
14. In the event leakage of electrolyte flush with water/neutralising
agent, seek medical help if it comes into contact with the eyes etc
.
15. Servicing of the appliance should be according to manufacturers instructions
.
This product
( include battery pack
) must be disposed of at a designated collection pint for electrical and electronic waste
.
For more information
, contact your local city office or the shop where you purchased the product
.
6.2 Robot Storage
Packed the mower and all spareparts with the original package, and storage the carton off the ground in a cool, dry place. Temperature should not be colder than
-4
F
°(- 20℃)
6.3 Blade replacement
Blade model: TC-GB
Specifications: 14L
Blade replace steps:
1.Stop the robot in safety conditions.
2. Wear protective gloves.
3. Turn the Robot upside down.
4. Unscrew the blade and remove it.
5. Replace a new blade and screw it.
6. Turn the mower to upside.
-
P31
-
6. MAINTENANCE AND STORAGE
6.4 Battery
The battery is maintenance-free, but has a limited life span of 1-3years.
Battery life is dependent on the length of the using season and how many hours per week the robot is used. A long season or many hours of use per week, means that the battery must be replaced more regularly.
IMPORTANT INFORMATION
Charge the battery fully at the end of the season before winter storage.
- Attentions for lead-acid batteries
Charge the batteries at least once every six months of they are at 25
℃
The interval of this charge should be reduced to
5 0% by each 10
℃ rise in temperature above 25
℃.
The self
discharger state
, their capacity may not recover ever after charge
.
If the batteries are
stored for more than a year at room temperature. The life of batteries
may be shortened.
Store the batteries starting from fully charged state to prevent the life of
the batteries being shortened.
Use the batteries as quickly as possible after receiving them as they
gradually deteriorate even under proper storage conditions.
- Attentions of lithium batteries
Please charge the lithium batteries in accordance with standard time and
procedures.
When the power is too low. It should be started charging as soon as
possible.
Storage, we suggest the optimum storage of lithium battery is with 40%
power and keep in the shade.
- Disused battery processing
Please contact the nearest waste treatment certer and consultation with
recycling and proper disposal of views.
-
P32
-
7. TROUBLE SHOOTING
7. Trouble shooting
Problem
Possible reasons
Solutions
After turn on the mower by key and set operate patten, but the mower still can not start. And the charging station is beeping.
1. The virtual wire fails to send signals.
2. The virtual is broken
1.Check the virtual wire light (colorless). Be sure the virtual wire is connected to the charging station that is motion, and there is no loose place.
2. Connect the wire with virtual wire connectors.
After turn on the mower by key and set operate patten, but the mower still can not start
No power to plug receptacle or main power is shut off.
Bad communication between charging station and mower
Check the power and check the plug.
Connect charging station with power supplier.
Mower stop working and beeping.
Mower is lifted over
2CM from the ground.
Put the mower in lever ground, turn off the mower and restart it.
Remote control does not work
The electricity power is low
Change batteries
-
P33
-
7. TROUBLE SHOOTING
Problem
Possible reasons
Solutions
Mower stop working and beeping.
1. Cutting height too low.
2. Blade or running wheels strike hard objects.
3. The mower is trapped in lawn.
1. Adjust the cutting height to suitable height.
2. Clean the grass and make sure it is free from hard objects.
3. Clear the lawn where the mower is trapped or restart the mower in another place.
Mower stop working and beeping.
Mower is tilted over than 30 degree from the ground
Put the mower in lever ground, turn off the mower and restart it by enter password and choose operate pattern.
Mower stop working and beeping.
1. Strike bump continuously.
2.Bump sensors are locked.
3.Wires of bump sensors have be cut off. Bump sensor is broken.
1. Restart the mower
2. Free bump sensors
3. Change new wires of bump sensors. Send the mower to provider and change the bumper sensors.
-
P34
-
7. TROUBLE SHOOTING
Problem
The batteries can not recharged
Possible reasons
Power nearing natural end of life
Solutions
1. Send the mower to service station and replace the battery
2. Check whether the charger is well connected.
Grass is extremely overgrown or very wet
Cut the grass appropriate height.
Terrain needs landscaping repairs.
Fill in all holes, cover or exclude all exposed roots in order to smooth the terrain.
Mower does not complete the edge.
Obstacle along the path
Watch the ful operation of edge and confirm no obstacle are present
Mower drives but blade will not mow.
1. On manual pattern,
Mow on remote control has be turned off.
2. The cutting motor is broken.
1. Turn on the mower button.
2. Send the mower to service station and replace a new cutting motor.
-
P35
-
7. TROUBLE SHOOTING
Problem
Short run time, operates less time than normal
Possible reasons
Power is not fully charged for operation
Solutions
Recharge the mower fully.
Mower does not detect the charging station contacts.
The ground before the charging station is not flat.
Reset the charging station in a flat place.
Mower reached the charging station when its contacts are above the charging station contacts.
Height difference between the charging station and the lawn surface at the entrance to the charging station.
Confirm the ground before the charging station is leveled with the charging station if necessary fill area with dirt and level off.
The robot behaves in an anomalous manner around the flower beds.
Virtual wire incorrectly placed
Relocate the virtual wire
The robot is very noisy
1. Damaged running motor
2. Grass too high
1. Get the motor repaired or replaced by
.
service station
2. Increase the cutting height or use a normal lawn mower.
-
P36
-
7. TROUBLE SHOOTING
Problem
The robot is very noisy
Possible reasons
Solutions
1. Damaged cutting blades
1. Replace the blade with a new one.
2. Cutting blade flooded by residues(tapes, ropes, plastic fragments, etc)
3.The start of the robot occurred with obstacles being too closed (less than 1m away) or in presence of unexpected obstacles (fallen branches, forgotten objects, etc.)
2. Stop the robot in safety conditions; use protection gloves to avoid the risk of cuts on hands; remove the fold cause from the blade.
3. Start the robot in a new place.
8. EXPLODED VIEW
8.1 Charging Station Exploded View
7
8
1
2
3
4
5
6
1.Light
2.Top cover
3.Power terminal
4.Virtual wire terminal
5.PCB
6.Underpan
7.Copper sheet permanent seat
8.Copper sheet
-
P37
-
P38
-
8. EXPLODED VIEW
8.2 Mower Exploded View
-
P39
-
P40
-
Handle-top
Handle-down
Up cover
Key switch
Lead-acid Battery
Batten of battery
Power light
Rain sensor
Emergency switch
Cutting motor
Blade holder
Blade
Motor pressure plate
Running motors
Running motor gear
Bearing pressure plate
Gear
Bearing
Axle
Wheel
Shell
Bottom cover
Lift sensor
Screw cap
Gasket
Omni-directional wheels
Spring sheet
Micro switch
PCB
Middle bumper
Charging head
Side bumper
Oilseal
Charging terminal
12
13
14
15
16
9
10
11
20
21
22
23
17
18
19
4
5
1
2
3
6
7
8
27
28
29
30
31
32
24
25
26
33
34
Advertisement
