User Manual
le Avantree’
User Manual
Bluetooth Audio Transmitter/Receiver 2-in-1
Saturn Pro
www.avantree.com
LED indicator Multi-function Button(MFE)
2. Product overview
(1) LED Indicator
(2) Multi-Function Button (MFB)
{Power On/Off / Pairing / Pause / Play) =
(3) Micro USB charging socket 4 Micro USE charging socket
(4) 3.5mm audio jack
(5) TX / RX switch
What's in the box:
Avantree Satum Pro
3.5mm audio cable
RCA audio cable
3.5mm audio connector
USB charging cable Yes
B
User manual Fo A ] | rise —
Quick starter guide Ea + 8
E F
9.
TONMOOPP
Warranty card
5) We recommend fully charging the device at least every two months.
*Charging times may vary when using different chargers.
4. Transmitter - Turn On / Off
Slide TX / RX switch to TX positon before turning on. Tha TX or RX mode cannot be
changed after powering up Saturn Pro.
Turn On: Press and hold the MFB for about 5 seconds until the LED lights blue for 1
second.
Turn Off: Press and hold the MFE for about 3 seconds until the LED shows red for 1
second and then goes out.
Note: For first time use or first time turn on after the connection list has been cleared,
ed:
5.1 Pairing procedure:
1) Ensure Saturn Pro is set to TX mode and that the device is off.
2) Plug the 3.5 mm audio cable into Satum Pro, and plug the other end into the
audio output of audio source system iPod, TV, Amplifier etc.)
3) Power on your Bluetooth stereo receiver and set it in pairing mode.
4) Press and hold Saturn Pro's MFB for around 7 seconds, until the LED indicator
blinks blue quickly - indicating pairing mode.
5) Place Saturn Pro within 1 metre of your Bluetooth receiver. Saturn Pro will then
automatically search, pair and connect with your Bluetooth receiver.
6) After successful connection, the LED indicator will blinks blue slowly.
1. Product description
The Avantres Saturn Pro is à 2-in-1 Bluetooth receiver and transmitter incorporating
the latest “aptX Low Latency" codec for Bluetooth High quality audio streaming.
The Saturn Pro is simple to use and enables any audio device to transmit and
receive. It can be used to enable a phone to transmit music to a home stereo system,
or just as easily, to allow a CD player or other device to transmit music to a Bluetooth
enabled speaker system or headphones.
With its low latency codec, Saturn Pro also supports online game playing; TV/Movie
audio transmission; real-time music recording, etc.
The compact design and internal rechargeable battery provides long play time and
versatility in use.
Saturn Pro is the ideal solution to stream audio without bounds or limits.
3. Charging
Saturn Pro comes with a built-in rechargeable battery that provides for long periods
of operation and standby time. We recommend charging the battery fully before
using Saturn Pro for the first time.
1) Insert one end of Micro USB charging cable to Saturn Pro Micro USB socket and
plug the other end into a standard USB power source, such as a laptop or desktop
computer.
2) The battery takes 3 hours to charge to its full capacity for the first time. Each
subsequent charge cycle should then take around 2 hours.
3) The LED indicator will show red when charging and will
go out when charging is complete, Da ua da
4) IF you have not used the device for a few months, the ( ©)
LED might not show red when first charging. It may take ts
15-35 minutes before the LED lights up. Red LED on when charging,
CH whan completed
.3.
in transmit mode Saturn Pro will automatically enter pairing mode, indicated by
the LED indicator flashing blue quickly.
5. Transmitter - Pairing with a Bluetooth device
Once Saturn Pro is powered up in TX mode and has connected to a bluetooth stereo
device, you can stream music wirelessly. Before pairing, please make sure your
Bluetooth stereo receiver device supports the Bluetooth A2DP profile.
|
| i || rem L 1 H} de lea
| Presa MFE7a, Press MFE Ts Wind until bot LEDS iy
| LED bieáa blu LED Blinks blir Elias mbr с
uc blue and red Éonnete bo Tv
Note:
1) Saturn Pro will flash the LED indicator blue 3 times within 5 seconds of connecting
with another Bluetooth device which also has an aptX low latency codec. When
both transmitter and receiver incorporate aptX low latency codecs, this will provide
for low latency and higher audio quality audio compared with standard Bluetooth
audio devices.
2) Pairing mode lasts for 2 minutes. if no devices can be connected with 2 minutes,
Satum Pro will enter standby mode.
3) Saturn Pro will pair with stereo Bluetooth receiver devices with the PIN codes
“0000”, “1111”, “8888” or "1234".
5.2 LED indications:
LED indicator Status of Saturn Pro under TX mode
LED blinks BLUE continuously Pairing mode, lasts for 2 minutes
LED flashes BLUE once every second Standby mode - nol connected lo any other device
LED flashes BLUE once every 5 seconds Device connected with SBC
LED flashes BLUE twice every 5 seconds Device connected with aptX
LED flashes BLUE three timas every 5 seconds | Device connected with aptX low latency
LED blinks RED Low battery power - Please recharge
We find that most problems are caused by improper pairing. Please follow the online
instructions step-by-step!
7.1 Pairing procedure:
1) Ensure Saturn Pro's TX/RX switch Is set to RX mode and that the device is off.
2) Plug the 3.5 mm audio cable into Saturn Pro's 3.5 mm audio socket and plug
the other end into the audio input of your home hi-fi stereo system.
3) Press and hold Saturn Pro's MFB for around 7 seconds until the LED indicator
quickly blinks blue and red alternately, indicating in pairing mode.
4) Place Saturn Pro within 1 metre of your Bluetooth enabled phone, Set your
smartphone to Bluetooth mode: Taking iPhone as an example: from your iPhone
home page, tap “Settings” \ “General * 1“ Bluetooth™ \ * On"
(Note: Different phones or tablets have different procedures to activate Bluetooth mode
and to pair and connect with other Bluetooth devices. The instructions here are just for
general guidance - please check your phone or tablet's documentation in case of
difficulties).
-10-
automatically. If you want to pair it to another devices, please turn off the current
paired device's Bluetooth mode and then try to pair Staurn Pro to the new
device, according to the above pairing procedure.
7.2 LED Indications:
LED indicator Status of Saturn Pro under RX mode
LED blinks BLUE then RED continuously Pairing mode. Lasts for 2 minutes.
LED Nashes BLUE once every second Standby mode. Not connected lo amy other device.
LED flashes BLUE once every 5 seconds Device connected with SEC
LED flashes BLUE twice every 5 seconds Device connected with aptX
LED flashes BLUE three times every 5 seconds/ Device connected with aptX low lalency
LED flashes BLUE four times every 5 seconds — | Device connected with AAC decode
LED blinks RED Low battery power. Please recharge.
- 12.
8. Reconnect
A. Automatic connect: When Saturn Pro is powered up, it will automatically
reconnect wilh the last connected device.
B. Manual connect: When Satum Pro is in standby mode and not connected to
any device, a single short press of the MFB will automatically reconnect the last
connected device.
C. Auto off: Saturn Pro will automatically power off if no devices are connected
within 5 minutes.
9. Restore factory default setting
Y Ensure pws 5 of
Ensure Saturn Pro is powered off, then press and hold (Fe pi en
the MFB for 10 -12 seconds, until both the BLUE and Sas? rare
RED LEDs are both on for about one second.
- 14 -
6. Receiver - Turn On / Off
Slide TX / RX switch lo RX mode before turning on. The TX or RX mode cannot be
changed after powering up Saturn Pro.
Turn On: Press and hold Saturn Pro's MFB for around 7 seconds until the LED
indicator shows blue for 1 second.
Turn Off: Press and hold the MFB for around 3 seconds until the LED shows red
for 1 second and then goes out.
7. Receiver - Pairing with a Bluetooth device
“CE RX Minds
© "| OC
Preas MFE 75
LED Binks Elisa SaanchPak Wail ni Both LED Birk Eden slowly
and red
5) iPhone will auto scan the available Bluetooth devices. Click on "Avantree Saturn
Pro” from the list of devices shown and according to the indication offered, tap
on "Yes" or "Confirm".
6) After pairing successfully, Satum Pro's LED indicator will blinks blue slowly.
Note:
1) Pairing mode will last 2 minutes. The receiver will enter standby mode if no
devices can be connected within 2 minutes.
2) If pairing fails, please power off Saturn Pro and re-pair according to above
procedures.
3) Saturn Pro can remember 8 paired devices. When the number of paired devices
exceeds 8, the oldest one will be removed from the list.
4) Every time Saturn Pro powers on, it will connect to the last connected device
= 11 -
7.3 Obtaining the maximum stable range.
Please ensure there are no obstacles (walls, comers, partitions etc.,) between the
receiving and transmitting devices. Also, when wearing devices, keep them to the
same side of your body .
How to get the maximum range Best Result
ro & Mobile KEEP SAME SIDE!
10. Product Specification
* Bluetooth 3.0 with EDR + Standby time: up to 150 hours
= Bluetooth profile: A2DP and AVRCP = Charging time: around 2-3 hours
* Audio codec: aptX-LL, aptX, SBC, AAC + Charging input voltage: DC 5V
= Operaling Range: Class 2, 10 meters = Battery: 270mAH rechargeable
* TX mode battery hours: up to 15 hours LI-Lon battery
= RX mode battery hours: up to 10 hours = Weight: Approx 48.59
Working and standby times may vary when used with different mobile phones or
other Bluetooth devices, usage settings, usage styles and environments.
11. Safety information
* To avoid any damage or malfunction of this device, do not drop the device from
high places.
= 15 =
* Keep this device away from humidity, water and all other liquids. If the device is
exposed to water, moisture or any other liquid, do nol operate it - this will mitigate
risk of explosion of or damage to the device or of electric shock or injury to yourself.
* Do not place or keep this device near any heat source, such as direct sunlight,
radiators, stoves or other apparatus which produces heal. This may cause an
explosion risk and/or degrade device performance and reduce battery life.
* Do not modify, repair or disassemble this device (especially the battery: this may
cause an explosion). Doing so will avoid the warranty.
* Do not place heavy objects on this device.
* Use only supplied and approved charger.
* Replacement or service must be performed only by a qualified service center or
the manufacturer.
* Unplug when not in use for long periods and during lightning storms.
= 16 -
CAUTIONS: ELECTRIC SHOCK HAZARD
The battery used in this device may present a risk of fire or chemical burn if istreated.
12. Declaration of Conformity
Trademark Statement
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
Avantree is a trademark owned by Avantronics limited.
apt-X™ words and logos marked with a ™ or % are trademarks registered or owned
by CSR plc or one of its group companies and may be registered in one or more
jurisdictions except that not all such marks are registered in all countries where
products are available.
п. © C € FCC ID: WJ5S-BTTC200
= 17 =
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement