(12). REC OUT JACKS(REC )

(13). TAPE IN(CD/TAPE IN)

These are input jacks that allow the signal from an external device to be added to the

MAIN output.

(14). SEND JACKS(SEND)

The signal level is sent to the built-in digital effect through the SEND jacks.

(15). RETURN JACKS(RETURN)

The level of the effect signal is returned from the built-in digital effect to the MAIN bus thr-

ough the RETURN jacks.

4. SPECIFICATIONS

Power handling: 100W

Frequency response: 70Hz-18KHz

Sensitivity(1m/1W): 93dB

Nominal impedance: 4ohms

LF driver: 1x10”with 1.5” voice coil

HF driver: 1x1” voice coil

HF protection: PTC protective circuit

Dimensions(WxDxH) 480x310x643mm

Net weight: 23.7KGS

3

USER'S MANUAL

0

C N EL 1

B

0

EFF

5

MIC IN

LINE

0

C N EL 2

B ASS

0

EFF

5

MIC IN

LINE

TR EBL

0

E

C N

L

B ASS

0

MIC IN

EFF

5

LINE

TR B E

0

C

0

MIC IN

LINE

EFF

5

BASS

0

EQUALI

0

A

5

EFF

5

0

L

5

R

POW ER

Please read this manual carefully and proper take care of this manual

1.IMPORTANT SAFETY SYMBOLS

The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.

The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.

Protective grounding terminal

Alternating current/voltage

Hazardous live terminal

ON: Denotes the apparatus is turned on.

OFF: Denotes the apparatus is turned off.

to the operator.

CAUTION: Describes precautions that should be observed to prevent the danger of the apparatus.

2.INTRODUCTION

* 4 Channel powered mixer

* Stereo output 100 watts RMS; load 4 Ohms;

* 4 input connectors on each channel; XLR or 1/4”phone jack.

* CD/TAPE input on back panel with level control on the front panel.

* Treble, bass,delay and level control on each channel.

* Master volume control.

* MIXER: (1) built-in Electronic Reverb.

3.FEATURES

Front panel

CHANNEL 4

1

(4) (1)(2)(3) (7) (6) (8) (9) (5)

Rear panel

EFFECT LOOP

SEND RETURN

(10) (11) (12) (13) (14) (15)

(1). EQUALIZER CONTROLS(TREBLE,BASS)

This is a 2-band equalizer that adjusts the high frequency range, mid frequency range, and

low frequency range of each channel.

TREBLE: 12.5KHz ±15dB shelving type

BASS: 80Hz ±15dB shelving type .

(2) EFFECT CONTROL(EFF)

This controls the amount of signal that is sent to the EFFECT bus for each channel.

(3) VOLUME CONTROL(VOLUME)

This adjusts the output volume for each channel.

(4) CHANNEL INPUT JACKS (MIC IN ,LINE)1~4

These are the input JACKS for channels 1~4.

(5) POWER SWITCH

This switch turns on/off the power of MIXER.

(6). EQUALIZATION CONTROL(EQUALIZATION)

This is a 3-band equalizer that allows you to adjust the frequency response of the MAIN bus

signal.

(7). TAPE IN CONTROL(TAPE IN)

This adjusts the amount of signal that is sent from the TAPE IN jack to the MAIN bus.

(8) EFF RETURN CONTROL(EFF RETURN)

This adjusts the level of the effect signal which is returned from the built-in digital effect to the

MAIN bus.

(9) MASTER CONTROL(MASTER)

This adjusts the final level of the MAIN bus.

(10). MAINS INPUT

(11). FUSE: ~ 115V-T3.15AH/250V

~

230V-T1.6AH/250V

2