High End Systems Cyberlight, Cyberlight CX, Cyberlight SV lighting User manual

High End Systems Cyberlight, Cyberlight CX, Cyberlight SV lighting User manual

Below you will find brief information for Cyberlight, Cyberlight CX, Cyberlight SV. The Cyberlight family of fixtures are ideal for theatrical applications, stage, studio, concert touring, and nightclubs. Cyberlight provides designers and operators with a luminaire (fixture) of unprecedented brightness, speed, accuracy, and effects for complex lighting cues and scenes. Each Cyberlight fixture can easily be programmed through the Status Cue system, the Cyberlight LCD controller, or another standard DMX controller into simple or complex scenes and sequences.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Cyberlight, Cyberlight CX, Cyberlight SV User Manual - High End Systems | Manualzz
®
®
®
User Manual
© High End Systems, Inc. 2005, All Rights Reserved
Information and Specifications in this document are subject to change without notice. High End
Systems, Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in
this manual. The system software for the Status Cue ® lighting console described in this manual is
furnished under a license agreement and may be used or copied only in accordance with the terms of
the agreement.
Printed in the U.S.A.
Trademarks
Trademarks used in this text: Cyberlight, Intellabeam, Lightwave Research, the Lightwave Research
logo, the High End Systems globe logo, Status Cue, Emulator, Trackspot, and LithoPatterns are
registered trademarks; and High End Systems and Psy-Dye are trademarks of High End Systems Inc.
Belden is a registered trademark of Belden, Inc. Philips is a registered trademark of Philips Lighting
Company. Other trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. High End Systems disclaims any proprietary
interest in trademarks and trade names owned by others.
Cyberlight / Cyberlight CX/Cyberlight SV User Manual
Version 2.2 March 2005
P/N 60600016
ii
Cyberlight User Manual
Declaration of Conformity
according to ISO/IEC Guide 22 and EN45104
Manufacturer’s name:
High End Systems
Manufacturer’s address:
High End Systems Inc.
2105 Gracy Farms Lane
Austin, Texas 78758
U.S.A.
Declares that the product
Product Name:
Cyberlight
Product Number:
CBL-01
CBL-CX
CBL-SV
Product Options:
All
CL Litho
CX Litho
SV Litho
conforms to the following EEC directives:
73/23/EEC, as amended by 93/68/EEC
89/336/EEC, as amended by 92/31/EEC and 93/68/EEC
Equipment referred to in this declaration of conformity was manufactured in compliance with the
following standards beginning in 1995:
Safety:
EN 60598-1 : 1993
EN 60598-2-17 : 1989
A1-A3 : 1993
EMC:
EN 50081-1 : 1992
EN 50082-1 : 1992
Lanny Derryberry, Compliance Engineer
U.S.A., December 20, 1996
Cyberlight User Manual
iii
IMPORTANT SAFETY INFORMATION
INSTRUCTIONS PERTAINING TO CONTINUED PROTECTION AGAINST FIRE, ELECTRIC
SHOCK, EXPOSURE TO EXCESSIVE ULTRAVIOLET (UV) RADIATION, AND INJURY TO
PERSONS ARE FOUND IN APPENDIX E.
PLEASE READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY, MOUNTING, AND OPERATING
THIS EQUIPMENT.
IMPORTANT: INFORMATIONS DE SÉCURITÉ
INSTRUCTIONS RELATIVES À UNE PROTECTION CONTINUE CONTRE L' INCENDIE, LE CHOC
ÉLECTRIQUE, L' EXPOSITION AUX RADIATIONS ULTRAVIOLETTES EXCESSIVES ET CONTRE
DES BLESSURES POSSIBLES SUR DES INDIVIDUS SE TROUVENT DANS L'APPENDICE E.
PRIÈRE DE LIRE TOUTES LES PRÉCAUTIONS ET LES AVERTISSEMENTS AVANT
D'ASSEMBLER, DE MONTER, ET DE FAIRE FONCTIONNER CET ÉQUIPEMENT.
WICHTIGE SICHERHEITSHINWEISE
DIE NACHSTEHENDEN HINWEISE BETREFFEN DEN SCHUTZ GEGEN BRAND,
ELEKTRISCHEN SCHLAG, ÜBERHÖHTE UV-STRAHLUNG SOWIE VERLETZUNGEN. SIE
BEFINDEN SICH IN APPENDIX E.
LESEN SIE ALLE WARNUNGEN SORGFÄLTIG, BEVOR SIE DAS GERÄT ZUSAMMENBAUEN,
INSTALLIEREN UND BENUTZEN!
INFORMACIÓN IMPORTANTE DE SEGURIDAD
SE ENCUENTRAN EN EL APÉNDICE E LAS INSTRUCCIONES CONCERNIENTES A LA
PROTECCIÓN CONTINUA CONTRA INCENDIO, CHOQUE ELÉCTRICO, EXPOSICIÓN
EXCESIVA A RAYOS ULTRAVIOLETAS Y LESIONES A PERSONAS.
POR FAVOR LEA TODAS LAS PRECAUCIÓNS Y LAS ADVERTENCIAS ANTES DE ENSAMBLAR,
MONTAR Y OPERAR ESTE EQUIPO.
INFORMAZIONI IMPORTANTI DI SICUREZZA
ISTRUZIONI PERTINENTI LA PROTEZIONE CONTRO IL FUOCO, LE SCOSSE ELETTRICHE, L'
ECCESSIVA ESPOSIZIONE AI RAGGI ULTRAVIOLETTI I DANNI ALLE PERSONE SI TROVANO
NEL APPENDICE E.
LEGGERE TUTTI GLI AVVERMENTI PRIMA DI MONTARE E USARE QUESTO APPARECCHIO.
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
iv
Cyberlight User Manual
Warranty Information
Limited Warranty
Unless otherwise stated, your product is covered by a two year parts and labor limited warranty.
Dichroic filters and LithoPatterns ® high resolution glass gobos are not guaranteed against
breakage or scratches to coating. It is the owner’s responsibility to furnish receipts or invoices
for verification of purchase, date, and dealer or distributor. If purchase date cannot be
provided, date of manufacture will be used to determine warranty period.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Authorization number (RA#) from your dealer or point of
purchase BEFORE any units are returned for repair. The manufacturer will make the final
determination as to whether or not the unit is covered by warranty. Lamps are covered by the
lamp manufacturer’s warranty.
Any Product unit or parts returned to High End Systems must be packaged in a suitable manner
to ensure the protection of such Product unit or parts, and such package shall be clearly and
prominently marked to indicate that the package contains returned Product units or parts and
with a Returned Authorization (RA#) number. Accompany all returned Product units or parts
with a written explanation of the alleged problem or malfunction.
Please Note: Freight Damage Claims are invalid for fixtures shipped in non-factory
boxes and packing materials.
Freight
All shipping will be paid by the purchaser. Items under warranty shall have return shipping
paid by the manufacturer only in the Continental United States. Under no circumstances will
freight collect shipments be accepted. Prepaid shipping does not include rush expediting
such as air freight. Air freight can be sent customer collect in the Continental United States.
REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. HIGH END SYSTEMS, INC. MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, AND
HIGH END SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. HIGH END SHALL NOT BE LIABLE FOR
ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST
PROFITS, SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR
CAUSED BY PRODUCT DEFECTS OR THE PARTIAL OR TOTAL FAILURE OF ANY
PRODUCT REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT
(INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, AND WHETHER
OR NOT SUCH DAMAGE WERE FORESEEN OF UNFORESEEN.
Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized
repairs or parts. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Cyberlight User Manual
v
Contents
Introduction
Cyberlight Features ..................................................................................................................
About This Manual...................................................................................................................
Caution, Warning and Explosion Symbols ..............................................................................
Getting Help .............................................................................................................................
Chapter 1
intro-1
intro-3
intro-4
intro-4
Installation and Setup
Unpacking the Cyberlight Fixture................................................................................................. 1-2
Specifications ................................................................................................................................ 1-3
The Cyberlight Family of Fixtures................................................................................................ 1-6
Optional Accessories..................................................................................................................... 1-7
Identifying Rear Panel Components ............................................................................................. 1-8
Obtaining and Installing the Power Cord Cap .............................................................................. 1-9
Setting the Cyberlight Fixture Voltage ....................................................................................... 1-10
Installing the Yoke ...................................................................................................................... 1-14
Installing or Replacing the MSR 1200 Lamp.............................................................................. 1-16
Installing SV Color Wheel Dichroic Filters................................................................................ 1-19
Setting the Personality DIP Switches.......................................................................................... 1-22
Rear Panel LED Indicators.......................................................................................................... 1-27
Putting the Fixture Into Use ........................................................................................................ 1-28
Where to Go From Here.............................................................................................................. 1-30
Chapter 2
Using Your Cyberlight
Choosing DMX 512 or LWR Protocol ......................................................................................... 2-2
Implementing DMX/LWR Control ............................................................................................... 2-3
Obtaining Cabling and Terminators.............................................................................................. 2-6
Linking the Fixtures to the Controller........................................................................................... 2-8
Mounting the Fixture..................................................................................................................... 2-9
Troubleshooting .......................................................................................................................... 2-12
Chapter 3
Servicing Your Cyberlight
General Maintenance and Cleaning .............................................................................................. 3-2
Replacing Parts............................................................................................................................ 3-15
Adjustments................................................................................................................................. 3-23
vi
Cyberlight User Manual
Appendix A
DMX Control of Cyberlight
Overview ...................................................................................................................................... A-1
Address DIP Switches .................................................................................................................. A-2
Related Topics .............................................................................................................................. A-2
Accessing Control Information .................................................................................................... A-2
Rounding Conventions ................................................................................................................. A-2
DMX 512 Mode 1 – Standard Cyberlight DMX Control............................................................. A-3
DMX 512 Mode 2 – Enhanced Cyberlight DMX Control ........................................................... A-7
DMX 512 Mode 3 – Cyberlight 15-Channel DMX Control ...................................................... A-13
Channel Boundaries.................................................................................................................... A-18
Appendix B
Cyberlight Mirror Movement Times
Appendix C
Factory-Installed Wheels
Appendix D
Typical Voltages Worldwide
Appendix E
Important Safety Information
Glossary
Index
Cyberlight User Manual
vii
Table of Figures
Figure 1-1. Identifying Cyberlight rear panel components. ...................................... 1-8
Figure 1-2. View of the bottom of the Cyberlight fixture, where the access door
latches are located............................................................................... 1-11
Figure 1-3. Removing the first four rear panel screws in order to access
the Cyberlight voltage selection jumpers. .......................................... 1-12
Figure 1-4. In order to remove the lamp box access door, you need to remove
the last two 5/32 inch allen screws, which are located by the
color mixing and dim flags. ................................................................ 1-12
Figure 1-5. On CL and CX models, make sure you disconnect the fan
power wires from the fan connectors before removing the
lamp box access door. ......................................................................... 1-13
Figure 1-6. Location of the voltage selection jumpers and the voltage
selection wire. ..................................................................................... 1-13
Figure 1-7. Location of the voltage selection tabs and connector. ......................... 1-13
Figure 1-8. Components of the Cyberlight yoke. ................................................... 1-14
Figure 1-9. Installing the yoke on the Cyberlight fixture. ...................................... 1-15
Figure 1-10. Location of lamp assembly and optimization screws. ....................... 1-16
Figure 1-11. Removing the lamp from its socket. .................................................. 1-17
Figure 1-12. Installing the new lamp into the socket. ............................................. 1-17
Figure 1-13. Placing Cyberlight fixture in setup mode allows you to
perform the necessary lamp optimization prior to using a
newly-installed lamp. ......................................................................... 1-18
Figure 1-14. Removing the center access door. ...................................................... 1-20
Figure 1-15. The color wheel is located between the effects wheel and the
color mixing flags, opposite the rotating litho wheel. ........................ 1-20
Figure 1-16. High End Systems recommends you replace the CL color
correction filter (at position 4) with the salmon-colored
CTO correction filter, and the aqua filter (at position 5)
with the homogenizing frost filter. ..................................................... 1-21
Figure 1-17. Push the dichroic filter toward the large retaining tab to free
it from the wheel clips. ....................................................................... 1-21
Figure 1-18. Orient the coated side of the dichroic toward the lamp and the
uncoated side toward the static litho wheel. ....................................... 1-22
Figure 1-19. The personality switches. ................................................................... 1-22
Figure 1-20. The Cyberlight rear panel LEDs give you information about
the Cyberlight fixture’s lamp, fixture voltage, operating
temperature, data transmission and reception, and other factors. ....... 1-24
Figure 1-21. Setting the Cyberlight power switch to the ON and OFF positions. .. 1-29
Figure 2-1. The address switch block allows you to select the control protocol
(DMX 1, DMX 2, DMX 3, or LWR) and the fixture number. ............. 2-4
Figure 2-2. Properly-constructed data cable. ........................................................... 2-6
Figure 2-3. Constructing a data cable terminator. ................................................... 2-7
viii
Cyberlight User Manual
Figure 2-4. Make sure you connect the Data Out connector from the
previous Cyberlight to the Data In connector of the next
Cyberlight. Also, you must terminate the Data Out connector
of the last device in the link (whether the last device is a
Cyberlight or something else). .............................................................. 2-8
Figure 2-5. Attaching two C-clamps to the Cyberlight yoke. ................................ 2-11
Figure 2-6. Always use suitable safety cables when hanging a Cyberlight
from a truss or any other support system. The safety cable can
be looped around the support and the Cyberlight yoke once or
twice; loop it twice if this will help prevent the fixture from
rotating, thus possibly loosening the clamp mounting bolt. ............... 2-11
Figure 2-7. Loosening the hub screws allows you to adjust the wheel’s
clearance. ............................................................................................ 2-18
Figure 2-8. Loosen these two allen screws to adjust the rotating litho wheel. ...... 2-19
Figure 2-9. The rotating litho wheel’s spring plunger must always contact
the rotating litho wheel. ....................................................................... 2-19
Figure 3-1. Holding the fan fins in place while you clean the fans using
compressed air. ..................................................................................... 3-3
Figure 3-1. Bottom view of the Cyberlight fixture. .................................................. 3-4
Figure 3-2. Locations of the iris, power lens, focusing lens, zoom lens and
mirror. ................................................................................................... 3-5
Figure 3-3. Locations of the Cyberlight motors. ....................................................... 3-5
Figure 3-4. Close the iris by rotating the large black gear located on top of the
iris motor. .............................................................................................. 3-6
Figure 3-5. Cleaning the anti-reflective glass. .......................................................... 3-6
Figure 3-6. Removing the standoff between the iris motor and the
color wheel. ........................................................................................... 3-7
Figure 3-7. Make sure the wheel is positioned with the keyhole slots
facing downward before removing it. ................................................... 3-7
Figure 3-8. The homing slot is a small groove on the outside edge of
the wheel. The static litho wheel and the color wheel’s homing
slots are in different locations. The effects wheel does not have a
homing slot. .......................................................................................... 3-8
Figure 3-9. Clean the groove in the wheel sensor. .................................................... 3-8
Figure 3-10. Static litho wheel lithos must be oriented with the
coated/etched side facing away from the lamp. .................................... 3-9
Figure 3-11. Color wheel dichroic filters should be oriented with the coated
side of the dichroic facing toward the lamp and the glass side
facing toward the static litho wheel. ..................................................... 3-9
Figure 3-12. Position the keyhole slots so they fit over both hex screws as
well as the “slider” screw inset in the hub. ......................................... 3-10
Figure 3-13. Location of lamp assembly and optimization screws. ........................ 3-11
Figure 3-14. Removing the lamp from its brass socket. ......................................... 3-11
Cyberlight User Manual
ix
Figure 3-15. Location of the first four rear panel screws you need to remove in
order to access the lamp assembly. ..................................................... 3-12
Figure 3-16. In order to remove the lamp box access door, you need to
remove the last two 5/32 inch allen screws, which are located
by the color mixing and dim flags. ..................................................... 3-12
Figure 3-17. On CL and CX models, make sure you disconnect the fan
power wires from the fan connectors before removing the
lamp box access door. ......................................................................... 3-13
Figure 3-18. Locations of the reflector and infrared filter. ..................................... 3-13
Figure 3-19. Location of the color mixing flags and dim flags. ............................. 3-14
Figure 3-20. View of the bottom of the Cyberlight fixture, where the access
door latches are located. ..................................................................... 3-16
Figure 3-21. Removing the rear panel screws allows you to access the
Cyberlight voltage selection jumpers. ................................................ 3-16
Figure 3-22. In order to remove the lamp box access door, you need to
remove the last two 5/32 inch allen screws, which are located
by the color mixing and dim flags...................................................... 3-17
Figure 3-23. On CL and CX models, make sure you disconnect the fan
power wires from the fan connectors before removing the
lamp box access door. ......................................................................... 3-17
Figure 3-24. Location of power supply board fuses. .............................................. 3-18
Figure 3-25. Removing the center access door. ...................................................... 3-19
Figure 3-26. Insert the new or cleaned litho into the rotating litho housing as
described above; improper installation can cause heat damage
to the litho. .......................................................................................... 3-20
Figure 3-27. Turn on the spring as you push it into the rotating litho
housing. .............................................................................................. 3-20
Figure 3-28. Make sure the end of the spring fits under any one of the
three retaining washers, as shown above. ........................................... 3-21
Figure 3-29. Do not place the end of the spring between the three
retaining washers. ............................................................................... 3-21
Figure 3-30. Push the dichroic/litho toward the large retaining tab to free
it from the wheel tabs. ........................................................................ 3-22
Figure 3-31. Adjusting the Cyberlight CX mechanical zoom lens. ........................ 3-23
Figure 3-32. Loosen the three 5/32 inch allen screws and the T-handle
to adjust the mirror head deviation. .................................................... 3-24
Figure 3-33. Grasp both sides of the mirror head and rotate it to the
desired position. .................................................................................. 3-25
Figure 3-34. Be sure to note the deviation angle in case you need to set
other fixtures for the same deviation, or if you want to use
this exact deviation again. For example, the figure above has
about a 10° + (plus) deviation. .......................................................... 3-25
Figure 3-35. Adjust the yoke handles on both sides of the Cyberlight
to tilt the fixture in a specific way. ..................................................... 3-26
x
Cyberlight User Manual
Figure A-1. The DMX address switch block allows you to select the
control protocol (DMX 1, DMX 2, DMX 3, or LWR) and the
fixture number. .................................................................................... A-2
Figure A-2. Unplanned channel addressing wastes DMX addresses because
of fixture boundary overlap. .............................................................. A-20
Figure A-3. Planned channel addressing wastes a minimum of DMX address
space. ................................................................................................. A-20
Figure C-1.
Figure C-2.
Figure C-3.
Figure C-4.
Figure C-5.
Figure C-6.
Figure C-7.
Factory configuration of the CX static litho wheel. ............................ C-1
Factory configuration of the CL/SV static litho wheel. ....................... C-2
Factory configuration of the CX rotating litho wheel. ........................ C-3
Factory configuration of the CL/SV rotating litho wheel. ................... C-4
Factory configuration of the CX color wheel. ..................................... C-5
Factory configuration of the CL/SV color wheel. ............................... C-6
Effects wheel for the CL, CX and SV models. .................................... C-7
Cyberlight User Manual
xi
Table of Tables
Table 1-1. Cyberlight Optional Accessories ............................................................ 1-7
Table 1-2: Cyberlight Information Mode ............................................................... 1-24
Table 1-3: Description of Cyberlight Rear Panel LEDs ......................................... 1-27
Table 2-1: Protocol Mode Switch Settings ............................................................... 2-5
Table 2-2: Cyberlight Fixture Number Settings (LWR Protocol) ............................ 2-5
Table 2-3: XLR Cable Pinouts ................................................................................. 2-7
Table 3-1: Description and Function of Power Supply Board Fuses ..................... 3-18
Table A-1: Addressing Fixtures in 20-Channel DMX 512 Mode 1 ........................ A-3
Table A-2: Cyberlight DMX Assignments Mode 1 ................................................. A-3
Table A-3: Addressing Fixtures in 20 Channel DMX 512 Mode 2 ......................... A-7
Table A-4: Cyberlight DMX Assignments Mode 2 ................................................. A-8
Table A-5: Addressing Fixtures in 15 Channel DMX 512 Mode 3 ....................... A-13
Table A-6: Cyberlight DMX Assignments Mode 3 ............................................... A-14
Table A-7: 20-Channel Addresses (Modes 1 and 2) .............................................. A-18
Table A-8: 15-Channel Addresses (Mode 3) ......................................................... A-19
xii
Cyberlight User Manual
Introduction
Congratulations on your purchase of the Cyberlight® automated luminaire manufactured by High
End Systems, Inc. Cyberlight — the most advanced intelligent lighting instrument available — is
ideal for theatrical applications, stage, studio, concert touring, and nightclubs. Cyberlight provides
designers and operators with a luminaire (fixture) of unprecedented brightness, speed, accuracy and
effects for complex lighting cues and scenes.
Your microprocessor-based Cyberlight fixture responds to an extensive set of programming
commands called constructs. You can easily program these constructs through the Status Cue
system, the Cyberlight LCD controller or another standard DMX controller into simple or complex
scenes and sequences. Examples of constructs are colors, color mixing, lithos, litho mixing,
rotating lithos, special effects, variable frost, dim, iris, and strobing.
This manual covers the Cyberlight versions listed below:
•
Cyberlight: The full-featured luminaire, with motorized variable frost from hard edge to soft
edge; beam position and movement speed; focus; variable zoom; litho and CYM (cyan-yellowmagenta) color selection; color mixing; variable iris; variable-speed rotating lithos (0-50
RPM); full optical dimming; and automatic cooling system shutdown. Additionally, the
fixture accepts stock and custom LithoPatterns, including Psy-Dye™ high resolution glass
gobos, Art Glass and Special Effects lithos.
•
Cyberlight Studio Version (SV): The quieter-operating, full-featured luminaire.
•
Cyberlight CX: The value-priced luminaire, with all of the features of the Cyberlight except
motorized zoom, color mixing and variable frost.
Cyberlight ® Features
The Cyberlight features can be categorized into four main areas, listed separately below: control/
information features, lamp, optics, effects, and other features.
Control/information features
•
Remote system enable/disable.
•
“Info” LED displays lamp hours, lamp strikes, lamp voltage, lamp current, fixture voltage,
fixture temperature, and the fixture version number for at-a-glance monitoring (no controller is
required).
•
Can be controlled by Lightwave Research (LWR) or standard USITT DMX 512 protocol:
•
Use LWR protocol for online software uploads and control with High End Systems’ topof-the-line Status Cue system, for uploads only with the Cyberlight Upload Module, and
for control only with the Cyberlight LCD controller.
•
Use DMX 512 protocol if the Cyberlight is on the same link as other vendors’ control
equipment.
Introduction
Intro-1
Lamp
•
1200 watt MSR/MSD lamp; 5600° Kelvin color temperature
•
750-hour rated lamp life
•
Quick lamp change and optimization
Optics
•
Computer-optimized reflector and lens assembly for maximum output
•
Enhanced mirror increases efficiency
•
Motorized zoom control (Cyberlight CL and SV models only; the CX has a 3-position zoom
at 12°, 14°, and 18°)
•
Zoom angle 12° to 18°—Cyberlight CL and SV only
•
Motorized focus control
•
Motorized variable frost from hard edge to soft edge
•
Smooth, precise micro-stepped beam positioning
•
100% dimming, fade to black
•
170° pan – 110° degrees tilt
•
Break-resistant mirror
Effects
Intro-2
•
16 million colors available via sophisticated dichroic subtractive CYM (cyan-yellow-magenta)
color model —Cyberlight CL and SV only
•
Eight-position indexed color wheel with a versatile selection of richly-saturated dichroic colors
plus open (white), custom dichroic filters available
•
Upward, downward, and centered color correction
•
Variable speed (forward and reverse 0-50 RPM) rotating lithos (from 0° to 360°) with
replaceable patterns (4 lithos plus open)
•
Eight-position fixed litho wheel with seven easily-replaceable LithoPatterns glass lithos
standard
•
Litho mixing effects: rotating over fixed, or fixed over fixed
•
Eight-position effects wheel, including multi-image prism effect, split color effect and
subtractive color dichroic mosaic effect
•
Infinitely-variable frost effect—Cyberlight CL and SV only
•
De-focus lens effect
•
Variable speed motorized iris control
•
Variable high-speed strobe shutter (1 to 10 FPS)
•
Variable speed mirror scan, litho, and color changes
Cyberlight User Manual
Other features
•
Pan and tilt swap; pan and tilt invert
•
Selectable voltage and frequency
•
Circuit breaker protection
•
Six transport handles
•
High-resolution stepper motors
•
Durable black powder coat finish
•
Yoke indexing with graduated scale reduces pre-focus time
•
Adjustable mirror head deviation ± 20 degrees (pan)
•
Thermal overload protection
•
Power factor correction
•
Meets international standards for safety and electromagnetic compatibility
About This Manual
This manual covers the following topics in its three chapters and five appendices:
•
Chapter 1: Unpacking your Cyberlight and preparing it for use.
•
Chapter 2: Putting the Cyberlight into operation, including the “how-tos” of DMX 512 and
LWR control protocols, connecting the fixture to a controller and mounting the fixture.
Troubleshooting suggestions are also included.
•
Chapter 3: Routine maintenance and service.
•
Appendix A: Explains the three DMX modes and how to use them.
•
Appendix B: Cyberlight mirror movement times.
•
Appendix C: Shows the factory configuration for the color, effects, static litho and rotating
litho wheels.
•
Appendix D: Typical voltage/frequency settings worldwide, based on High End Systems
Inc.’s experience.
•
Appendix E: Important safety information.
•
Glossary
•
Index
Introduction
Intro-3
Caution, Warning and Explosion Symbols
The following three international symbols appear in margins throughout this manual to highlight
caution and warning messages.
Caution: This symbol appears adjacent to Caution messages. Not heeding these messages could
result in personal injury and damage to equipment.
Warning: This symbol appears adjacent to High Voltage Warning messages. Not heeding these
messages could result in serious personal injury.
Explosion: This symbol appears adjacent to Explosion warning messages.
Getting Help
U.S. and
Canada
From 8 a.m. to 5 p.m. (U.S. Central time) Monday through
Friday:
(800) 890-8989
24-hour FAX:
(512) 834-9195
24-hour voice mail: (512) 837-3063 or (800) 890-8989
24-hour BBS:
Intro-4
(512) 339-3043
24-hour
World Wide
Web site
http://www.highend.com
Europe
Voice:
FAX:
+49 8122 9903-0
+49 8122 9903-33
Singapore
Voice:
FAX:
+65 742 8266
+65 743 9322
Cyberlight User Manual
Chapter 1
Installation and Setup
1
Unpacking the Cyberlight Fixture .................................................................................................. 1-2
Save the Shipping Materials.................................................................................................... 1-2
Inspecting the Contents ........................................................................................................... 1-2
Specifications................................................................................................................................. 1-3
Model and Part Numbers......................................................................................................... 1-3
Physical Specifications............................................................................................................ 1-3
Electrical Specifications .......................................................................................................... 1-4
Safety Standards ...................................................................................................................... 1-4
Safety Specifications ............................................................................................................... 1-4
Cables and Connectors ............................................................................................................ 1-5
The Cyberlight Family of Fixtures ................................................................................................ 1-6
Nomenclature .......................................................................................................................... 1-6
Optional Accessories ..................................................................................................................... 1-7
Identifying Rear Panel Components.............................................................................................. 1-8
Obtaining and Installing the Power Cord Cap............................................................................... 1-9
Important Power Cord Cap Information - U.K. Only ............................................................. 1-9
VIGTIG FIKKER HEDS INFORMATION - DANMARK ................................................. 1-10
Setting the Cyberlight Fixture Voltage........................................................................................ 1-10
Changing the Voltage Selection Jumpers.............................................................................. 1-11
Installing the Yoke....................................................................................................................... 1-14
Installing or Replacing the MSR 1200 Lamp .............................................................................. 1-16
Resetting the Information Counter ........................................................................................ 1-18
Optimizing the Cyberlight Fixture Lamp .............................................................................. 1-18
Installing SV Color Wheel Dichroic Filters ................................................................................ 1-19
Setting the Personality DIP Switches .......................................................................................... 1-22
Personality Switch Setting Descriptions ............................................................................... 1-23
Switch 1: Self-Test ........................................................................................................ 1-23
Switch 2: Setup Mode ................................................................................................... 1-23
Locating the Information LED...................................................................................... 1-24
Switches 3, 4, and 5: Information Mode ....................................................................... 1-24
Interpreting the Information LED .......................................................................... 1-25
Switch 6: Pan Invert ...................................................................................................... 1-26
Switch 7: Tilt Invert....................................................................................................... 1-26
Switch 8: Pan/Tilt Swap ................................................................................................ 1-26
Rear Panel LED Indicators .......................................................................................................... 1-27
Putting the Fixture Into Use......................................................................................................... 1-28
Setting the Cyberlight Power Switch .................................................................................... 1-29
Where to Go From Here .............................................................................................................. 1-30
Chapter 1 Installation and Setup
1-1
Unpacking the Cyberlight® Fixture
First, unpack your fixture and verify that it arrived complete and without any damage.
Save the Shipping Materials
Do not discard the shipping carton and packing materials. The carton and packing materials are
specifically designed to protect the product during transport.
High End Systems assumes no responsibility for products damaged during transport. Therefore,
you should return a product for repair in its original shipping carton and packing materials.
Note
Before sending anything to the factory, be sure to call your HES dealer/distributor for a
Return Authorization (RA) number. The factory cannot accept any goods shipped without
an RA number.
Inspecting the Contents
Carefully unpack the carton and inspect the contents for damage. If any of the items in the
following list are missing or damaged you must notify both the shipping agent and your sales agent
immediately.
1-2
•
One copy of this manual
•
One Cyberlight fixture
•
One MSR 1200 lamp (packaged in a separate box)
•
One yoke enclosed in cardboard packaging with a yoke handle kit consisting of two yoke
handles, two 5/16 inch carriage bolts, two 5/16 inch allen screws, and two 9/16 inch locknuts
•
SV only: Two color wheel dichroic filters enclosed in individual containers (one CTO
correction filter, one homogenizing frost filter)
Cyberlight User Manual
Specifications
This section lists specifications for the Cyberlight family of fixtures.
1
Model and Part Numbers
•
Models:
•
Manufacturer:
Cyberlight, Cyberlight CX, Cyberlight SV
High End Systems, Inc.
2105 Gracy Farms Lane
Austin, Texas, 78758
USA
•
Product Numbers:
CL Litho
CX Litho
SV Litho
Physical Specifications
•
Fixture weight:
42.23 kg (92.9 lb) for Cyberlight
39.77 kg (87.5 lb) for Cyberlight CX
44.32 kg (97.5 lb) for Cyberlight SV
•
Yoke weight:
1.27 kg (2.8 lb)
•
Total fixture weight:
45.6 kg (95.7 lb) Cyberlight
41.04 kg (90.3 lb) Cyberlight CX
45.59 kg (100.3 lb) Cyberlight SV
•
Dimensions (CL and CX):
cm: 106.7 L x 33.0 W x 31.7 H
in: 42.0 L x 13.0 W x 12.48 H
•
Dimensions (SV):
cm: 106.7 L x 33.0 W x 36.6 H
in: 42.0 L x 13.0 W x 14.41 H
•
Dimensions with handles (all models):
add 5.08 cm (2 in) to length
and 7.62 cm (3 in) to width
•
Lamp type:
Use 1200 W, G-22 Base, MSR 1200 or MSD 1200 Metal
Halide Lamp Only
Chapter 1 Installation and Setup
1-3
Electrical Specifications
•
•
•
•
•
Voltage selectable:
Power consumption:
Rated power:
Rated frequency:
Power Factors:
208V / 230V only
6.3/6.3A
1300W
50-60Hz
230V, 50Hz: 0.85
208V, 60Hz: 0.97
(1)
Class I equipment - For continued protection against electric shock
connect this equipment to an earthed (grounded) power source only.
(2)
This equipment for connection to branch circuit having a maximum
overload protection of 20 A.
Safety Standards
•
Safety standards
•
EN 60598-1 : 1993
•
EN 60598-2-17 : 1989
A1-A3 : 1993
•
EMC Standards
•
EN 50081-1 : 1992
•
EN 50082-1 : 1992
Safety Specifications
1-4
•
•
•
•
•
•
Maximum ambient temperature:
Maximum exterior surface temperature:
Minimum distance to lighted object:
Minimum distance to flammable objects:
Maximum winding temperature, Tw:
Maximum capacitor temperature, Tc:
•
Do not mount on a flammable surface.
•
Not for residential use.
•
Use in dry locations only.
Cyberlight User Manual
50° C (122° F)
62° C (144° F)
1.0 m (3.28 ft.)
1.0 m (3.28 ft.)
180° C (356° F)
85° C (185° F)
Cables and Connectors
•
DMX data cables: Belden® 9841 or equivalent (meets specifications for EIA RS-485
applications) with characteristics listed below:
•
2-conductor twisted pair plus a shield
•
maximum capacitance between conductors - 30 pF/ft.
•
maximum capacitance between conductor and shield - 55 pF/ft.
•
maximum resistance of 20 Ω/1000 ft.
•
nominal impedance 100–140 Ω
•
22–24 AWG with insulation having a dielectric rating of 300 volts or higher
•
DMX data connectors: Standard 3-pin male and female XLR connectors
•
DMX data terminators: Male XLR connector with 120 ohm terminator (see Chapter 2)
Chapter 1 Installation and Setup
1
1-5
The Cyberlight® Family of Fixtures
Currently, the Cyberlight family of automated luminaires (fixtures) consists of three models:
The Cyberlight (referred to in this manual as the CL model):
cy b er lig h t
LIGH TWAVE RE SEAR CH
R
LITH O
AU STIN, TEXAS U .S. A.
The Cyberlight SV (referred to in this manual as the SV model):
LIGHT WAVE RESEAR CH
R
AUST IN, TEXAS U. S.A.
The Cyberlight CX (referred to in this manual as the CX model):
cyberlight
LIGHTWAVE RESEARCH
R
LITHO
AUSTIN, TEXAS U.S.A.
Nomenclature
Because all three Cyberlight models have different features and functions, some references in this
manual will be to one specific model only. Other references might encompass all three models.
The following nomenclature system will be used throughout this manual so you will know which
fixture model is being referred to:
1-6
•
A generic reference to Cyberlight applies to all three models (CL, CX and SV).
•
A reference to CL applies to the Cyberlight CL only.
•
A reference to CX applies to the Cyberlight CX only.
•
A reference to SV applies to the Cyberlight SV only.
Cyberlight User Manual
Optional Accessories
Table 1-1 below shows the optional accessories for Cyberlight available from your High End
Systems dealer/distributor:
1
Table 1-1. Cyberlight Optional Accessories
Name
Part Number
Status Cue controller
Call*
Cyberlight LCD controller with
unprogrammed RAM card
19020001
Unprogrammed RAM card
80440017
Replacement MSR 1200 lamp
55030001
Cyberlight LithoPatterns
Call*
Cyberlight custom color wheel
dichroic filters
Call*
Cyberlight touring yoke kit
55040005
Cyberlight dust filter kit
55040006
Cyberlight narrow angle lens kit
55040012
Keal road case (1 fixture)
19070001
Keal road case (2 fixtures)
19070001
Heavy duty 3-pin XLR cable (10’)
55050005
Heavy duty 3-pin XLR cable (25’)
55050006
Heavy duty 3-pin XLR cable (50’)
55050007
Heavy duty 3-pin XLR cable (100’)
55050008
Galvanized safety cable
12040001
Deluxe C-clamp
55000004
Call* - Contact either your High End Systems dealer/distributor, High End Systems Sales, or the
High End Systems World Wide Web site. The Web site includes product information and pictures
of all currently-available LithoPatterns.
High End Systems International Sales: See the inside title page of this manual
High End Systems World Wide Web site: http://www.highend.com
Chapter 1 Installation and Setup
1-7
Identifying Rear Panel Components
This section describes the rear panel components, LEDs, switches, and connectors.
Figure 1-1. Identifying Cyberlight rear panel components.
1-8
1.
Quality Control (QC) plate - displays (from top to bottom) the fixture’s model number, serial
number, factory voltage setting, maximum volts and amps, manufacturing date and the initials
of the engineer responsible for Quality Control (QC) of the fixture.
2.
Lamp Assembly – removable from the rear of the fixture for easy lamp replacement (see
“Installing or Replacing the MSR 1200 Lamp” on page 1-16).
3.
Lamp Assembly Retaining screws – these two screws fasten the lamp assembly to the fixture
(see “Installing or Replacing the MSR 1200 Lamp” on page 1-16).
4.
Power On/Off Switch – press the “I” side to turn fixture power ON. Press the “O” side to turn
fixture power OFF.
5.
Lamp Optimization Screws – these three screws align the lamp for optimal output (see page
1-18).
6.
Address DIP Switch Settings – this chart lists the fixture number settings and shows how to
select either Lightwave Research (LWR) control protocol or one of three DMX 512 modes (see
“What is DMX 512 Protocol?” on page 2-2).
Cyberlight User Manual
7.
Status and Information LEDs – these LEDs provide the following information:
• the top LED displays pertinent fixture information, such as lamp hours, strikes,
current, and so on (see page 1-23 and page 1-24)
• the middle three LEDS display status of the motors, lamp, and fans (see page 1-27)
• the bottom two LEDs blink when data is transmitted to or received from a controller
(see page 1-27)
8.
Data Out XLR Connector – connect this to the Data In connector of the next device in the
link (see “Linking the Fixtures to the Controller” on page 2-8).
9.
Data In XLR Connector – connect an XLR cable from the Data Out connector of the
previous device in the link (see “Linking the Fixtures to the Controller” on page 2-8).
1
10. Personality DIP Switches – use these switches to set the operating mode of the fixture (see
page 1-22).
11. Address DIP Switches – use these switches to set the fixture address and to select the control
protocol (see “Setting the Address DIP Switches” on page 2-4).
12. Personality DIP Switch Settings – this chart lists the switch settings for the operating mode
of the fixture.
Obtaining and Installing the Power Cord Cap
You must obtain and install a power cord cap before you can connect the Cyberlight to a power
outlet. The type of power cord cap you must obtain depends on the location in which the
Cyberlight will be used; different locations (even within the same country) might have different
power cord cap requirements.
Note
Because of the wide variety of power cord caps used worldwide, High End Systems cannot
make specific recommendations for the particular power cord cap you should use. Contact a
local authority if you are unsure which type of power cord cap you need.
Important Power Cord Cap Information - U.K. Only
IMPORTANT The cores in the mains lead are colored in accordance with the following code:
•
•
•
green and yellow: earth
blue: neutral
brown: live
Since the colors of the cores in the mains lead of this equipment may not correspond with the
colored markings identifying the terminals in your plug, proceed as follows:
•
•
•
The core which is colored green and yellow must be connected to the terminal in the plug
which is marked with the letter “E” or by the earth symbol
, or colored green or green and
yellow.
The core which is colored blue must be connected to the terminal which is marked with the
letter “N” or colored black.
The core which is colored brown must be connected to the terminal which is marked with the
letter “L” or colored red.
Class 1 equipment: THIS EQUIPMENT MUST BE EARTHED.
Chapter 1 Installation and Setup
1-9
VIGTIG FIKKER HEDS INFORMATION - DANMARK
ADVARSEI: RESKYTTEKSE MOD ELEKTRISK SHOCK.
VIGTIGT!
LEDERE MED GROEN/GUL ISOLATION
MA KUN TILSLUTTES EN KLEMME MAERKET
ELLER
Setting the Cyberlight ® Fixture Voltage
The Cyberlight fixture voltage is factory-set to customer requirements. Normally, the factory
setting is correct for your typical use. However, if you change venues and need to change the
fixture’s input voltage, refer to the procedure in this section. (Appendix D has a listing of typical
power requirements worldwide.)
By moving one wire on the power supply board you can set the input voltage to any of the
following:
205 volts 50 hertz
230 volts 50 hertz
240 volts 50 hertz
Warning
1-10 Cyberlight User Manual
208 volts 60 hertz
230 volts 60 hertz
Check the voltage selection jumper before proceeding with the equipment
setup! Be sure to match the voltage selection jumper to your power
source prior to operating this equipment. Do not set the voltage selection
jumper with the equipment plugged in.
Changing the Voltage Selection Jumpers
You will need:
- one right angle 5/32 inch allen wrench
Warnings: (1) An unshielded MSR/MSD 1200 lamp emits ultraviolet and visible
(UV-vis) radiation which could damage eyes and skin. Wear eye and
hand protection when re-lamping. Never look directly at the lamp while
lamp is on.
(2) Hot lamp may be an explosion hazard. Do not open for 5 minutes
after switching off.
(3) Equipment surfaces may reach temperatures up to 62° C (144° F).
Allow 10 minutes for cooling before handling.
(4) To avoid the risk of electric shock, turn the fixture OFF and unplug it
from the power source before performing this service.
1.
After allowing the fixture to cool as described above, turn the power switch OFF and unplug
the fixture. Refer to the section titled “Setting the Cyberlight Power Switch” on page 1-29 for
power switch settings.
2.
With the fixture oriented bottom-side up, remove the center access door by sliding the two door
latches inward. Lift the door straight up, unhook the safety chain, and set the door aside. See
Figure 1-2.
Figure 1-2. View of the bottom of the Cyberlight fixture, where the access door
latches are located.
Chapter 1 Installation and Setup 1-11
1
3.
Remove the fixture’s lamp box access door by removing six 5/32 inch allen head screws as
follows:
•
Remove the four 5/32 inch allen head screws from the bottom of the rear panel as shown in
Figure 1-3.
Figure 1-3. Removing the first four rear panel screws in order to access the
Cyberlight voltage selection jumpers.
•
Remove the last two 5/32 inch allen head screws from the color mixing plate as shown in
Figure 1-4.
Remove these two 5/32 inch allen screws
Color mixing plate
Figure 1-4. In order to remove the lamp box access door, you need to remove the last
two 5/32 inch allen screws, which are located by the color mixing and dim flags.
1-12 Cyberlight User Manual
4.
Carefully lift the lamp box access door from the fixture.
5.
CL and CX models only: As you lift the assembly, disconnect the two fan power connectors
(black and red wires) from the power supply board as shown in Figure 1-5. Set the lamp box
access door aside. You now have access to the power supply board.
Figure 1-5. On CL and CX models, make sure you disconnect the fan power wires
from the fan connectors before removing the lamp box access door.
Figure 1-6. Location of the voltage selection jumpers and the voltage selection wire.
6.
Locate the four voltage and frequency selection tabs shown in Figure 1-7; they are on the left
side of the power supply board.
Figure 1-7. Location of the voltage selection tabs and connector.
Chapter 1 Installation and Setup 1-13
1
7.
Note which of the four tabs currently has the jumper wire attached. If you need to change the
voltage/frequency setting, grasp the connector and pull or wiggle it to remove it from the tab.
Make sure you pull on the connector and not on the wire.
8.
Move the voltage selection wire to the desired tab and firmly press the connector onto it. If the
connector has spread from use, gently squeeze it together with pliers. A loose connector will
overheat and turn brown.
9.
Reinstall the lamp box access door with the six screws in the reverse order in which you
removed them (see Step 3 on page 1-12).
10. Connect the safety chain to the center access door and replace the door (see Step 1 on page
1-11).
Installing the Yoke
You will need:
(The items listed below are shipped with the Cyberlight)
– two 5/16 inch carriage bolts
– two clamping T-handles
– yoke
– two 5/16 inch allen cap screws
– two 9/16 inch locknuts (nut with nylon insert)
(The items listed below are NOT shipped with the Cyberlight)
- 5/16 inch allen wrench
- 9/16 inch socket wrench or 9/16 inch wrench
1.
If the fixture has been running recently, allow it to cool for at least 10 minutes. Then turn the
power OFF.
2.
Remove the center access door. You do not need to unlatch the safety chain.
3.
Stand the fixture on its end handles.
4.
Insert the carriage bolts through the star-shaped hole in the yoke and attach the clamping Thandles to the carriage bolts. The T-handles should not be very tight; you will adjust them
later. Figure 1-8 shows the orientation of parts.
Yoke
Clamping
T-Handle
5/16 inch allen
bolts – insert through
yoke and into
fixture
5/16 inch carriage
bolts
9/16 inch
locknuts
Figure 1-8. Components of the Cyberlight yoke.
1-14 Cyberlight User Manual
Clamping
T-handle
5.
Do both of the following when you place the yoke on Cyberlight:
•
Make sure the U-shape of the yoke is opposite the center access door, as shown in Figure
1-9.
•
Align the bottom holes on the yoke with the yoke pivot hole labeled in Figure 1-9.
6.
Insert the two 5/16 inch allen bolts through the round holes in each side of the yoke, and
through the holes in the side of the Cyberlight. Tighten them using your fingers or an allen
wrench.
7.
Place a locknut on the end of each 5/16 inch allen bolt. You can use either a 9/16 inch socket
wrench or a 9/16 inch wrench to turn the nut. Tighten the nut until so you are still able to pivot
the fixture.
8.
Position the yoke as desired, using the deviation degree markings on the yoke for exact
positioning. When you have placed the fixture correctly, firmly tighten the T-handles.
Yoke tilt plate
LIGHT WAV E RE SE AR CH
50
N
de gree s
AU ST IN, T EX AS U.S. A.
60
V I A TI O
2010 0 1020 30
50
D
Yoke pivot hole
E
40
30
70 80
LITH O
60
80 70
cy b er lig h t
40
T-handle
Figure 1-9. Installing the yoke on the Cyberlight fixture.
9.
On the top of each yoke are three 13 mm (1/2-inch) diameter mounting holes which provide
two different ways to mount the fixture. For more information, see the section titled “Mounting
the Fixture” on page 2-9.
Chapter 1 Installation and Setup 1-15
1
Installing or Replacing the MSR 1200 Lamp
You will need:
– 1200 W, G-22 Base, MSR1200 or MSD1200 Metal Halide Lamp
Only
– Protective eye wear
– Protective gloves
Warnings (1) This equipment is designed for use with Philips® type MSR1200 or
MSD1200, 1200 watt lamp only. Use of any other type lamp may be
hazardous and will void the warranty.
(2) Change the lamp if it becomes damaged or thermally deformed.
(3) An unshielded MSR/MSD 1200 lamp emits ultraviolet and visible
(UV-vis) radiation which could damage eyes and skin. Whenever you are
working on or near an exposed MSR/MSD 1200 lamp, wear protective
eye gear. Never look directly at the lamp while lamp is on.
(4) Hot lamp may be an explosion hazard. Do not open for 5 minutes
after switching off. Wear eye and hand protection when re-lamping.
1.
Allow the fixture to cool as described above, then power OFF the fixture and unplug it from the
power source.
2.
Fully back out the two lamp assembly screws shown in Figure 1-10. The screws have retaining
springs that prevent them from being removed.
Figure 1-10. Location of lamp assembly and optimization screws.
3.
Grip the assembly by the three lamp optimizing screws and pull the assembly straight out the
back of the fixture. The lamp’s power cord is long enough to allow you to pull the lamp
assembly entirely free of the Cyberlight.
4.
When the lamp assembly is free, pull the old lamp straight up and out of the assembly as
shown in Figure 1-11:
1-16 Cyberlight User Manual
1
Brass socket
Figure 1-11. Removing the lamp from its socket.
5.
Put on your protective gloves. Remove the plastic shell containing the new lamp. Break the
seal, open the container and remove the lamp.
6.
Hold onto the ceramic lamp base and gently press the two lamp base pins into the brass lamp
sockets as shown in Figure 1-12. Do not force the lamp into the socket; doing so could break
the lamp.
Cautions
(1) Avoid touching any part of your skin to the lamp’s quartz envelope.
Oil and residue from your fingers can create a “hot spot” on the lamp,
causing premature lamp aging.
(2) Do not adjust the three optimization screws labeled in Figure 1-12. You
will adjust these screws in a separate procedure, described in the section
titled “Optimizing the Cyberlight Fixture Lamp” on page 1-18.
Brass socket
Optimization screws
(do not adjust)
Figure 1-12. Installing the new lamp into the socket.
7.
Before you insert the lamp assembly back into the fixture, clean the lamp with the alcohol wipe
shipped with the lamp. Otherwise, fingerprints and other contaminates will shorten lamp life.
8.
Carefully guide the lamp assembly straight back into the fixture and make sure the lamp is
inserted into the reflector. Be careful not to crimp the two lamp wires as you insert the lamp
assembly. Firmly tighten the two lamp assembly screws to secure the assembly to the fixture.
Chapter 1 Installation and Setup 1-17
Resetting the Information Counter
The information counter tracks the cumulative length of time (in hours) the lamp has been on and
the number of lamp strikes (the number of times the lamp has been illuminated). To reset the
counter after changing the MSR lamp, perform the following steps:
1.
Turn the fixture power OFF (refer to Figure 1-21).
2.
Set personality switches 3, 4, and 5 ON.
3.
Note the current settings of all address switches, then set all address switches OFF, except for
switch 6. Address switch 6 must be set ON.
4.
Turn the fixture power ON (the fixture will not home).
5.
Set personality switches 3, 4, 5, and address switch 6 (from Step 3) OFF.
6.
Return the address switches to their previous settings.
Optimizing the Cyberlight Fixture Lamp
Caution
Never operate the Cyberlight fixture without first optimizing the lamp.
Damage to the fixture can occur if the lamp is misaligned.
In order to get optimal light output you need to position the lamp’s arc at the focal point of the
fixture’s reflector (i.e., optimize the lamp). You can do this by following the procedure below:
1.
Make sure the fixture’s power switch is OFF (see the section titled “Setting the Cyberlight
Power Switch” on page 1-29). Then plug the fixture’s power cord into the electrical outlet.
2.
Place the Cyberlight in “setup” mode by setting personality DIP switch 2 ON as shown in
Figure 1-13. Make sure that all the remaining personality DIP switches are OFF.
Off
On
personality
12345678
Set switch 2
ON; all other
switches OFF
Figure 1-13. Placing Cyberlight fixture in setup mode allows you to perform the
necessary lamp optimization prior to using a newly-installed lamp.
3.
Turn the fixture power ON. The fixture homes before striking the lamp. During the homing
operation you will hear clattering sounds as the wheels, shutter, and mirror seek their home
positions. This is normal. (If the lamp fails to strike, make sure personality switch 2 is set
ON.)
4.
Point the beam at a flat surface several feet away and make sure the beam has a round shape
(not an oval) by following the suggestions below. (If a perfectly flat surface is not available,
point the beam at the flattest surface you can find.)
1-18 Cyberlight User Manual
•
•
5.
If the Cyberlight is already connected to a controller, bring a litho into focus. Then select
the open positions on all wheels (static litho, rotating litho, color and effects). Now
optimize as explained in this section. Procedural information for selecting effects can be
found in the documentation provided with your controller. If you are using DMX 512
protocol to control your Cyberlight, also see Appendix A.
If the Cyberlight is not connected to a controller, either lay the fixture flat on its back or
stand it on its end handles. Point the beam at a flat surface several feet away. Manually
swivel either the mirror or the fixture to make the beam as round as you can.
Using the three adjusting screws (shown in Figure 1-10), adjust the beam until it is at its
maximum brightness and the light level is even across the beam. If you cannot obtain an even
brightness across the entire beam, try to obtain an even brightness across the brightest (hot
spot) point of light near the center of the beam.
Hint: If you have difficulty optimizing the lamp or run out of adjustment on one of the
adjustment screws, turn all three screws fully out and start over.
6.
After you have optimized the lamp, set personality switch 2 OFF; the shutter closes. The lamp
will turn off in a few minutes. Wait until the fans have shut off before turning the fixture OFF.
Installing SV Color Wheel Dichroic Filters
This section applies to the SV model only. The SV ships with a color wheel configured identically
to the CL, plus two additional color wheel dichroic filters you can use in place of the factoryinstalled dichroic filters. The two additional filters are described below:
•
The CTO color correction dichroic filter is salmon-colored and can be used to color-correct the
SV to a 2950° K (tungsten) color temperature to match tungsten-filament lighting fixtures.
•
The homogenizing frost filter helps optimize the color mixing system by making the light color
and intensity even across the entire beam.
High End Systems recommends that you substitute the CTO color corrector for the CL color
corrector and the homogenizing frost filter for the aqua filter.
Please heed the following precautions when handling and using these filters:
•
Avoid touching the center of the glass. Handle the edge of the glass when
removing or installing the filters. If possible, wear cloth gloves when
inserting and removing filters from the color wheel.
•
If necessary, clean the filters with a mild glass cleaner and a soft cloth.
Chapter 1 Installation and Setup 1-19
1
1.
Remove the fixture’s center access door as shown in Figure 1-14.
Figure 1-14. Removing the center access door.
2.
Rotate the color wheel until the dichroic you wish to replace is in a position for easy access.
Figure 1-15 shows the location of the color wheel. Figure 1-16 shows the position of the
dichroics in the color wheel.
Figure 1-15. The color wheel is located between the effects wheel and the color
mixing flags, opposite the rotating litho wheel.
1-20 Cyberlight User Manual
Color Wheel Before
Color Wheel After
1. Open
2. Red
3. Purple
4. CL Color Corrector
5. Aqua
6. Blue
7. Orange
8. Indigo
1. Open
2. Red
3. Purple
4. CTO Color Corrector
5. Homogenizing Filter
6. Blue
7. Orange
8. Indigo
You will replace
these two dichroics
5
6
4
7
3
2
8
1
Open
Figure 1-16. High End Systems recommends you replace the CL color correction
filter (at position 4) with the salmon-colored CTO correction filter, and the aqua filter
(at position 5) with the homogenizing frost filter.
Note
3.
Wheel positions are numbered starting at the open hole (position 1). The other seven
positions are numbered counter-clockwise from position 1 when you are facing the color
wheel toward the lamp.
Push the filter you wish to replace toward the center of the wheel to free it from the two wheel
tabs as shown in Figure 1-17:
Figure 1-17. Push the dichroic filter toward the large retaining tab to free it from the
wheel clips.
4.
Once the dichroic is free of the two wheel tabs, pull it out of the wheel. Place the dichroic you
just removed in a safe place where it will not get scratched.
5.
Orient the CTO color corrector so the coated side is facing the lamp, and with the glass side
facing away from the lamp as shown in Figure 1-18. (The smoky-looking homogenizing frost
Chapter 1 Installation and Setup 1-21
1
filter can be installed with either side facing the lamp.)
Figure 1-18. Orient the coated side of the dichroic toward the lamp and the uncoated
side toward the static litho wheel.
Caution
6.
Be careful not to allow the filters to contact other objects during
installation. Doing so could scratch them.
Push the new filter into the large retaining clip on the wheel, then pull it up so it fits under the
wheel tabs.
Setting the Personality DIP Switches
There are two sets of DIP switches located on the rear panel of the Cyberlight fixture: personality
(the top set) and DMX address (the bottom set). Refer back to Figure 1-1 if you are not sure of the
location of these switches.
The personality switches (shown in Figure 1-19) determine the fixture’s operating mode. You can
use these switches for testing, setup, and for control of specialized parameters. Setting all the
switches OFF is the normal operating mode when using the fixture with a Lightwave Research
(LWR) protocol controller, such as the Status Cue system or the Cyberlight LCD controller. Note
that a switch is ON when it is adjacent to the switch number and OFF when it is away from the
switch number.
Figure 1-19. The personality switches.
1-22 Cyberlight User Manual
Personality Switch Setting Descriptions
All Switches Off: Normal Mode
When all switches are OFF, the fixture must be controlled by Lightwave Research (LWR)
control protocol. For more about LWR and DMX 512 control protocols, see Chapter 2.
Switch 1: Self-Test
Switch 1 On – Setting switch 1 ON starts an internal self-diagnostic routine which verifies the
major functions of the fixture.
After setting switch 1 to ON, the fixture homes (you will hear gears turning and clacking). Except
for the homing procedure, which is performed only once, the self-test repeats until you set switch 1
back OFF.
Note
Setting switch 1 ON overrides any controller that might be attached to the fixture. You
must set switch 1 back to OFF before attaching a controller to the fixture.
A controller is not required for the self-test. However, if you do have a controller you might want to
verify fixture functionality under either DMX or LWR control. If you are using the Status Cue
system to control the Cyberlight, refer to its documentation for the procedure. If you are using
another controller, refer to the documentation shipped with the controller and also to Appendix A.
Switch 1 Off – This is the normal operating mode. During normal operation the motor, fan, and
lamp LEDs on the rear panel are ON (see Table 1-3 for a description of rear panel LEDs).
Switch 2: Setup Mode
Switch 2 On – Setting switch 2 ON causes the lamp to strike. This allows you to adjust (optimize)
the lamp without connecting the fixture to a controller. It is very important to optimize the lamp
before operating the fixture with a newly-installed lamp. Failure to do so could result in damage to
the fixture. (See “Optimizing the Cyberlight Fixture Lamp” on page 1-18.)
Note
Setting switch 2 ON overrides any controller that might be attached to the fixture. You
must set switch 2 back to OFF before attaching a controller to the fixture.
Switch 2 Off – Normal operation.
Chapter 1 Installation and Setup 1-23
1
Locating the Information LED
Before describing the remainder of the Cyberlight switches, you need to know the location of the
information LED on the rear panel of the fixture. Figure 1-20 shows the location of this LED:
Figure 1-20. The Cyberlight rear panel LEDs give you information about the
Cyberlight fixture’s lamp, fixture voltage, operating temperature, data transmission
and reception, and other factors.
Switches 3, 4, and 5: Information Mode
Personality switches 3, 4, and 5 control what the “info” LED displays. For example, setting
switches 3, 4, and 5 all OFF causes the “info” LED to display the number of hours the lamp has
been on. The other information controlled by personality switches 3, 4, and 5 is shown in Table 12:
Table 1-2: Cyberlight Information Mode
Set Switches
3
4
5
Off
Off
Off
Off
On
On
On
On
Off
Off
On
On
Off
Off
On
On
Off
On
Off
On
Off
On
Off
On
To Read this Information
Lamp Hours
Lamp Strikes
Lamp Voltage
Lamp Current
Fixture Voltage
Fixture Temperature
Reserved
Fixture Version Number
A detailed description of the information displayed in Table 1-2 is shown below:
Lamp Hours [off-off-off] – The total number of hours the lamp has been on since the counter was
reset.
Lamp Strikes [off-off-on] – The total number of lamp strikes.
Lamp Voltage [off-on-off] – The lamp voltage value at the moment of this sample.
Lamp Current [off-on-off] – The lamp current value at the moment of this sample.
Fixture Voltage [on-off-off] – The fixture voltage value at the moment of this sample.
Fixture Temperature [on-off-on] – The fixture temperature (in °C) at the moment of this sample.
Reserved [on-on-off] – These switches are reserved for future expansion.
Version number [on-on-on] – The fixture’s software version number.
1-24 Cyberlight User Manual
Interpreting the Information LED
The “info” LED on the Cyberlight fixture’s rear panel indicates numerical values by blinking.
Individual digits in a number are separated by a short pause. Iterations of the same number are
separated by a long pause.
The value that the info LED represents is determined by personality switches 3 through 5. Once
you set the switches as shown in Table 1-2 on page 1-24, the same value is repeated until you
change the switch settings.
Example #1: The number 3 would appear as shown below:
Example #2: The number 230 would appear as shown below:
Chapter 1 Installation and Setup 1-25
1
VERESE
A
ARCH
AUS
T IN , T E
XASU. S
. A
.
L IG H T
W
cy ber ligh t
Switch 6: Pan Invert
Switch 6 inverts the pan motor, which allows two opposing fixtures to respond to joystick control in
the same direction.
Switch 6 On – Reverses pan motor movement.
L IG H T WA V
E
U .S .A .
Switch 7: Tilt Invert
cy b er li
ght
AUST
I N
, TEXA
S
E
RSEARCH
Switch 6 Off – This is the normal operating mode. The pan motor moves in its normal direction.
Switch 7 inverts the tilt motor, which allows two opposing or upside down fixtures to respond to
joystick control in the same direction.
Switch 7 On – Reverses tilt motor movement.
Switch 7 Off – This is the normal operating mode. The tilt motor moves in its normal direction.
Switch 8: Pan/Tilt Swap
Switch 8 swaps the pan motor and tilt motor operation, which allows perpendicularly-hung fixtures
to respond to joystick control in the same direction.
Switch 8 On – Swaps the pan motor and tilt motor movement.
Switch 8 Off – This is the normal operating mode. The pan and tilt motors move in their normal
directions.
1-26 Cyberlight User Manual
Rear Panel LED Indicators
Table 1-3 lists the meanings of the information and status LEDs located on Cyberlight fixture’s rear
panel. Refer back to Figure 1-1 earlier in this chapter for the location of the rear panel LEDs.
Table 1-3: Description of Cyberlight Rear Panel LEDs
LED Name
LED Color
Description
info
red (blinks)
Provides fixture status information. See
“Switches 3, 4, and 5: Information Mode” on
page 1-24.
motor
green
Normal.
off
Check power supply board fuses as shown in
“Replacing Power Supply Fuses” on page
3-15.
steady
yellow
Normal.
flashing
yellow
(1 flash/
sec)
Lamp failed to strike. See “Troubleshooting”
on page 2-12.
rapid
flashing
Over-temp condition. See “Troubleshooting”
on page 2-12.
off
Timed out from loss of data.
red
Normal.
off
Fans have automatically shut off.
yellow
The fixture is transmitting data back to a
controller.
off
No data is being transmitted.
green
The fixture is receiving data from a controller.
off
No data is being received.
lamp
fan
xmit
recv
If you believe that the LEDs are indicating a problem situation, or if you are experiencing problems
with your fixture, see the section titled “Troubleshooting” on page 2-12.
Chapter 1 Installation and Setup 1-27
1
Putting the Fixture Into Use
Before putting the Cyberlight fixture into use, you need to do the following:
•
Make sure the Cyberlight power cord cap is wired correctly.
•
Make sure the Cyberlight is set for the correct voltage. Appendix D contains a listing of
typical voltages worldwide. You should always verify the proper voltage with a local authority
in your venue.
•
Make sure you configured the fixture properly as described in this chapter.
•
If you are connecting the fixture to a controller, see Chapter 2. If you are controlling the
Cyberlight with DMX 512 protocol, also see Appendix A (for DMX 512 control).
•
See the section titled “Mounting the Fixture” on page 2-9.
•
Heed all of the warnings below:
WARNINGS:
1-28 Cyberlight User Manual
•
Do not mount on a flammable surface.
•
Maintain minimum distance of 1.0 meter (3.28 feet) from
combustible materials.
•
Observe minimum distance to lighted objects of 1.0 meter (3.28
feet).
•
This equipment for connection to branch circuit having a
maximum overload protection of 20 A.
•
Equipment suitable for dry locations only. Do not expose this
equipment to rain or moisture.
•
Refer servicing to qualified personnel; no user serviceable parts
inside.
•
Class I Equipment - this fixture employs a grounded type
receptacle and is not intended for connection to a two wire,
ungrounded source of supply.
•
Heed all other Cautions and Warnings in this manual and printed
on fixture labels.
Setting the Cyberlight Power Switch
It is very important that you turn the Cyberlight power switch OFF before performing certain
procedures. Figure 1-21 shows the power switch in its ON and OFF positions:
Figure 1-21. Setting the Cyberlight power switch to the ON and OFF positions.
Warnings (1) This equipment for connection to branch circuit having a maximum
overload protection of 20 A.
(2) Class I Equipment—This fixture employs a grounded type receptacle
and is not intended for connection to a two wire, ungrounded source of
supply.
Chapter 1 Installation and Setup 1-29
1
Where to Go From Here
The following topics are covered in the remainder of this manual:
•
Chapter 2: Using your Cyberlight. Covers the differences between DMX 512 and LWR
control protocols; implementing LWR protocol; linking fixtures to the controller; mounting the
fixture; and troubleshooting suggestions.
•
Chapter 3: Servicing your Cyberlight. Shows how to perform routine cleaning on mirrors,
motors and lenses; replacing power supply fuses; replacing dichroics or lithos; adjusting the
CX mechanical zoom lens; adjusting the mirror head deviation; and adjusting the yoke
deviation.
•
Appendix A: DMX control of Cyberlight. Explains the three DMX modes and how to use
them. Also shows the relationship between the Cyberlight fixture number and the DMX
address range it uses.
•
Appendix B: Cyberlight mirror movement times. A table that correlates speed numbers to
mirror movement times, in units of seconds.
•
Appendix C: Factory-installed wheels. Shows the factory-installed options for the effects
wheel, color wheel, static litho wheel and rotating litho wheel for all three Cyberlight models.
•
Appendix D: Typical voltages worldwide. A table of typical voltage/frequency settings from
around the world, based on High End Systems’ experience.
•
Appendix E: Important safety information. Multi-lingual warnings you must observe
whenever operating the Cyberlight fixture.
•
Glossary
•
Index
1-30 Cyberlight User Manual
Chapter 2
Using Your Cyberlight®
Choosing DMX 512 or LWR Protocol........................................................................................... 2-2
What is DMX 512 Protocol? ................................................................................................... 2-2
What is LWR Protocol? .......................................................................................................... 2-2
Controlling Multiple High End Systems Fixtures on the Same Link...................................... 2-3
Implementing DMX/LWR Control ............................................................................................... 2-3
Setting the Address DIP Switches........................................................................................... 2-4
Address Switch Descriptions ........................................................................................... 2-4
Switches 1 through 6: Set LWR Protocol Fixture Number.............................................. 2-4
Switches 7 and 8: Protocol Mode..................................................................................... 2-5
Obtaining Cabling and Terminators ............................................................................................... 2-6
Constructing Cabling............................................................................................................... 2-6
Terminators ............................................................................................................................. 2-7
Linking the Fixtures to the Controller ............................................................................................ 2-8
Mounting the Fixture ...................................................................................................................... 2-9
Standing the Fixture on its End Handles ................................................................................. 2-9
Mounting the Fixture on a Truss or Other Support System .................................................. 2-10
Troubleshooting............................................................................................................................ 2-12
Checking and Correcting Wheel Clearances......................................................................... 2-18
Chapter 2 Using Your Cyberlight
2
2-1
Choosing DMX 512 or LWR Protocol
Before connecting your Cyberlight to a controller, you need to understand the difference between
DMX 512 and Lightwave Research (LWR) control protocols.
What is DMX 512 Protocol?
DMX 512 is an industry-standard method of controlling lighting fixtures and other devices (such as
lasers and hazers). Developed by the United States Institute of Theatre Technology (USITT), DMX
512 is supported by leading entertainment industry equipment manufacturers, such as High End
Systems.
DMX 512 (D for digital, MX for multiplex and 512 is the number of channels per link) is a reliable,
efficient and well-understood control protocol. Its strength lies in its ability to control a large
number of different types of devices made by various vendors on the same link using any DMXcompatible controller.
High End Systems recommends setting the Cyberlight for DMX 512 protocol (mode 2) for the
following reasons:
•
The Cyberlight dynamically responds to both DMX 512 and LWR protocols. The fixture will
switch to LWR protocol for software uploads, then switch back to DMX 512 control with no
user intervention. (LWR protocol is the only way to perform software uploads for the
Cyberlight using either a Link Card or the Cyberlight Upload Module.)
•
DMX mode 2 affords the most features and best resolution of all three DMX modes. (See
Appendix A for more detailed information.)
What is LWR Protocol?
LWR protocol is another way to control fixtures, and is the protocol used for Cyberlight software
uploads using either a Link Card or the Cyberlight Upload Module. However, LWR protocol can
be used to control only Cyberlight fixtures, Intellabeam® automated luminaires, Emulator® laser
simulators and Trackspot® automated luminaires with a controller that supports LWR protocol.
(Other vendors besides High End Systems have controllers that support LWR protocol. Consult the
documentation provided with your controller for information about protocol support.)
Setting a Cyberlight for LWR protocol would be a good idea if the following are true:
•
You have only Cyberlight fixtures on a link and are controlling them with the Cyberlight LCD
controller, the Status Cue system or another controller that supports the LWR protocol.
•
You have only Cyberlight fixtures, Trackspot fixtures and/or Intellabeam fixtures attached to a
link and are controlling them with the Status Cue system. You cannot have any other vendor’s
equipment on the same link.
Note
2-2 Cyberlight User Manual
At the time of this writing, you cannot perform a Cyberlight software upload using another
vendor’s controller, even if the controller supports LWR control protocol.
Controlling Multiple High End Systems Fixtures on the Same
Link
High End Systems recommends, if possible, that you do not mix Cyberlight fixtures with other
High End Systems equipment on the same link. There are two reasons for making this
recommendation:
•
Cyberlight fixtures have the largest number and variety of effects to control; therfore, putting
only Cyberlight fixtures on a link saves you the trouble of having to remember which fixtures
respond to which commands.
•
Intellabeam fixtures, Emulator fixtures and AF1000 fixtures will stop software uploads to
Cyberlight fixtures farther down the link. Therefore, if you are going to mix Cyberlight
fixtures with Intellabeam fixtures and AF1000 fixtures on the same link, make sure you put all
of the Intellabeam fixtures and AF1000 fixtures after all of the Cyberlight fixtures.
2
Implementing DMX/LWR Control
Once you have decided whether to control your Cyberlight fixture using DMX 512 or LWR
protocol, the procedure for connecting the fixtures to a controller is exactly the same. You need to
follow the four basic steps listed below. Each step will be explained in greater detail during the
remainder of this chapter.
Note
Please consult the documentation provided with your controller for controller-specific
information not covered in the remainder of this chapter.
•
Set the Cyberlight address DIP switches: Select either LWR or DMX protocol and other
options. This is covered in the section titled “Setting the Address DIP Switches” on page 2-4.
•
Obtain cabling and terminators: Obtain the right kind of cabling and obtain or build a
terminator for each link. This is covered in the section titled “Obtaining Cabling and
Terminators” on page 2-6.
•
Link the fixtures to the controller: Use XLR data-grade cable to link fixtures to the
controller and be sure to terminate the last device in the link. This is covered in the section
titled “Linking the Fixtures to the Controller” on page 2-8.
•
Mount the fixture: Plan your installation and mount the fixture. This is covered in the section
titled “Mounting the Fixture” on page 2-9.
Chapter 2 Using Your Cyberlight
2-3
Setting the Address DIP Switches
The previous sections in this chapter have helped you decide whether to control your Cyberlight
using DMX 512 protocol or LWR protocol. This section explains how to implement that decision
by selecting the protocol and by selecting a fixture number.
The eight DMX address DIP switches set the following options:
•
Whether the Cyberlight will be controlled using DMX 512 protocol or LWR protocol.
•
If you select DMX 512 protocol, you first need to determine which DMX mode you wish to
use, then set the fixture number. See Appendix A for a complete description of these options.
•
If you select LWR protocol, you need to set the fixture number. This is covered in the section
titled “Switches 1 through 6: Set LWR Protocol Fixture Number”.
Address Switch Descriptions
Figure 2-1 below shows a functional breakdown of the address DIP switches:
Figure 2-1. The address switch block allows you to select the control protocol (DMX 1,
DMX 2, DMX 3, or LWR) and the fixture number.
Switches 1 through 6: Set LWR Protocol Fixture Number
If you are using LWR protocol to control your Cyberlight, these switches set the fixture number.
Refer to Table 2-2 for switch settings. (If you are controlling your Cyberlight using DMX 512
protocol, refer to Appendix A.)
You need to assign a unique fixture number to each Cyberlight you wish to respond independently
to control commands. Multiple fixtures can be assigned the same address if you wish them all to
respond to control commands in the same way.
For example, suppose you have 12 Cyberlight fixtures on one link. You want six of them to operate
independently of each other and the other six to operate in exactly the same way. You need to
assign each of the six independently-operating Cyberlight fixtures a unique fixture number, but you
can assign a single fixture number to the other six, for a total of seven fixture numbers.
Note
2-4 Cyberlight User Manual
A unique fixture number is required for each Cyberlight for software uploads.
Switches 7 and 8: Protocol Mode
Use these switches to define the communication protocol between the fixture and the controller. By
default, switches 7 and 8 are both set OFF, which enables the use of Lightwave Research (LWR)
protocol for fixture control. This means you must use a controller that supports LWR protocol. The
Status Cue system and the Cyberlight LCD controller (both manufactured by High End Systems)
support LWR protocol. In addition, other vendors have controllers that support LWR; consult the
documentation provided with your controller for more information.
2
Table 2-1: Protocol Mode Switch Settings
Switches 7 and 8:
7
8
off
off
on
on
off
on
off
on
Mode
LWR
DMX 1
DMX 2
DMX 3
Table 2-2: Cyberlight Fixture Number Settings (LWR Protocol)
For This Fixture
Number
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
Set These DIP
Switches ON
none
1
2
1 and 2
3
1 and 3
2 and 3
1, 2, and 3
4
1 and 4
2 and 4
1, 2, and 4
3 and 4
1, 3, and 4
2, 3, and 4
1, 2, 3, and 4
For This Fixture
Number
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Set These DIP
Switches ON
5
1 and 5
2 and 5
1, 2, and 5
3 and 5
1, 3, and 5
2, 3, and 5
1, 2, 3, and 5
4 and 5
1, 4, and 5
2, 4, and 5
1, 2, 4, and 5
3, 4, and 5
1, 3, 4, and 5
2, 3, 4, and 5
1, 2, 3, 4, and 5
Chapter 2 Using Your Cyberlight
2-5
Obtaining Cabling and Terminators
There are two main types of cabling you can use: microphone cable and data-grade cable.
Although pin-compatible microphone cable is suitable for small-scale designs, data cable is
recommended, especially for longer cable runs. Data cable is designed to carry a higher-quality
signal with less susceptibility to electromagnetic interference.
The cable you use should have the characteristics listed below:
•
2-conductor twisted pair plus a shield
•
maximum capacitance between conductors - 30 pF/ft.
•
maximum capacitance between conductor and shield - 55 pF/ft.
•
maximum resistance of 20 Ω/1000 ft.
•
nominal impedance 100–140 Ω
•
22–24 AWG with insulation having a dielectric rating of 300 volts or higher
For example, Belden 9841 data-grade cabling meets specifications for EIA RS-485 applications
and is highly recommended for use with Cyberlight.
Constructing Cabling
Follow the instructions in this section if you need to construct cabling. You should construct cables
using shielded, two-conductor cable with a male 3-pin XLR connector at one end and a female 3pin XLR connector on the other end. Pinouts for both male and female XLR connectors are shown
in Figure 2-2.
Negative
Shield
Positive
Female XLR Connector
Figure 2-2. Properly-constructed data cable.
2-6 Cyberlight User Manual
Negative
Male XLR Connector
You should test each cable with a voltage/ohm meter (VOM) to verify correct polarity and to make
sure that the negative and positive pins are not grounded or shorted to the shield or to each other.
Also, make sure that pin 1 is shielded.
Table 2-3: XLR Cable Pinouts
Pin 1 is the shield
Pin 2 is the data compliment (negative)
2
Pin 3 is the data true (positive)
Caution
Do not use the ground lug on the XLR connectors. Do not connect the
shield to ground or allow contact to ground. Grounding the shield could
cause a ground loop and/or erratic behavior.
Terminators
The last device on each link must have a 120 ohm, 1/4 watt (minimum) terminator attached to its
Data Out connector. (This is true for both DMX 512 protocol or LWR protocol.) Two terminators
are shipped with each link card (supplied with the Status Cue system).
You can construct terminators by following the instructions below:
1. Obtain a male XLR connector.
2. Disassemble the connector.
3. Solder a 120 ohm resistor,
minimum of 1/4 watt, between pins 2 and 3.
4. Reassemble the XLR connector.
5. Install the terminator in the Data Out port of
the last device in the link.
1
2
3
Figure 2-3. Constructing a data cable terminator.
Chapter 2 Using Your Cyberlight
2-7
Linking the Fixtures to the Controller
Starting with the controller, link fixtures using the procedure below. Refer also to Figure 2-4.
1.
Start with the controller. Consult the documentation provided with the controller for the
procedure to connect XLR cable to its Data Out connector.
2.
Connect the female end of the XLR cable from the controller to the first Cyberlight fixture’s
male Data In connector.
3.
Connect the male end of another XLR cable to the first Cyberlight fixture’s female Data Out
connector.
4.
Continue connecting the Data Out connector from one Cyberlight to the Data In connector to
the next Cyberlight until you have linked all of the Cyberlight fixtures.
5.
Connect other devices to the Cyberlight fixtures as desired, using the instructions in the
documentation provided with those devices.
6.
Place a male 120 ohm terminator on the female Data Out connector of the last device in the
link. (This is true for both DMX 512 protocol or LWR protocol.) The procedure for making a
terminator can be found in the section titled “Terminators” on page 2-7.
Figure 2-4. Make sure you connect the Data Out connector from the previous
Cyberlight to the Data In connector of the next Cyberlight. Also, you must terminate
the Data Out connector of the last device in the link (whether the last device is a
Cyberlight or something else).
2-8 Cyberlight User Manual
Mounting the Fixture
Cyberlight is designed to be mounted in any orientation; you can even stand the fixture on its end
handles. However you wish to mount the fixture, you must follow the precautions and suggestions
below:
•
Verify the input voltage you are using matches the Cyberlight fixture’s voltage selection
jumpers (see the section titled “Electrical Specifications” on page 1-4 and “Changing the
Voltage Selection Jumpers” on page 1-11).
•
Heed the cautions and warnings below to guard against personal injury and damage to the
fixture.
Cautions
2
(1) This equipment for connection to branch circuit having a maximum
overload protection of 20 A.
(2) Class I Equipment - This fixture employs a grounded type receptacle
and is not intended for connection to a two wire, ungrounded source of
supply.
(3) Mount the fixtures and controllers in a location that is away from
direct heat and protected from moisture. Do not mount on a flammable
surface.
(4) Maintain minimum distance of 1.0 meter (3.28 feet) from combustible
materials. Observe minimum distance to lighted objects of 1.0 meter
(3.28 feet).
Standing the Fixture on its End Handles
The Cyberlight end handles are designed to support the weight of the fixture; however, make sure
you observe the following guidelines:
•
The fixture must be located away from moving objects that could strike it and cause it to
become unbalanced.
•
The fixture must be mounted on a sturdy, stable surface.
•
If the surface is other than floor height, make sure you use safety cables as described in the
next section.
Chapter 2 Using Your Cyberlight
2-9
Mounting the Fixture on a Truss or Other Support System
If you are mounting the fixture on a truss or another type of support, do all of the following:
•
Verify the truss or support will handle the weight of all the devices you are mounting.
Cyberlight fixture weights are listed in the section titled “Physical Specifications” on page
1-3.
•
The use of user-supplied safety cable is strongly recommended. You must supply your
own safety cable and you must verify the cable is capable of supporting the weight of the
fixture as listed in the section titled “Physical Specifications” on page 1-3. You can order
galvanized safety cables from your High End Systems dealer/distributor (part number
12040001). Also see Figure 2-6 on page 2-11.
•
You must supply your own clamps to attach the fixture to the support. You can attach one
or two clamps to the Cyberlight yoke. Verify that the clamp(s) you use are capable of
supporting the weight of the fixture as listed in the section titled “Physical Specifications”
on page 1-3. You can order deluxe C-clamps for a two-inch truss from your High End
Systems dealer/distributor (part number 55000004). Also see Figure 2-5 on page 2-11.
•
Make sure the fixture cannot be rotated all the way around (360o). (Using two clamps is a
good way to do this.) Allowing the fixture to rotate 360o could loosen the clamp mounting
bolts.
Note
Because of the variety of conceivable lighting designs, you should consider the procedure
below as a suggested guideline only. High End Systems cannot make specific
recommendations for your particular lighting design or venue.
Suggested mounting procedure:
1.
You should use three people to mount each Cyberlight fixture: two people to hold the fixture
while it is being secured in place, and one person to secure the fixture to its support and to
attach clamps and safety cables.
2.
Always stand on a firm, stable surface. The fixture should be at a height where you can
comfortably work on it, and should also be resting on a stable surface. Do not try to hold up
the fixture yourself while you are working on it; as Step 1 suggests, the ideal method is to have
a crew of three people to install the fixture.
3.
Attach a suitable clamp through one of the holes on top of the Cyberlight fixture yoke. If you
are attaching one clamp, use the middle hole on the yoke. If you are attaching two clamps (as
shown in Figure 2-5), attach one clamp to each of the holes on either side of the center hole.
Use locking washers when attaching the clamp to the yoke.
2-10 Cyberlight User Manual
2
Figure 2-5. Attaching two C-clamps to the Cyberlight yoke.
4.
Tighten the clamps firmly to the Cyberlight yoke and to the support.
5.
Loop one or more suitable safety cables around the support and around the top of the
Cyberlight yoke, as shown in Figure 2-6.
Figure 2-6. Always use suitable safety cables when hanging a Cyberlight from a
truss or any other support system. The safety cable can be looped around the
support and the Cyberlight yoke once or twice; loop it twice if this will help prevent the
fixture from rotating, thus possibly loosening the clamp mounting bolt.
Chapter 2 Using Your Cyberlight 2-11
Troubleshooting
This section lists typical symptoms and solutions for problems you might encounter when using
your Cyberlight. If you need additional help, or if the problem you are experiencing is not listed
here, contact your dealer/distributor or High End Systems Customer Service in one of the ways
shown in the section titled “Getting Help” on page Intro-4.
Contents of this section:
Fixture does not work: no LEDs, fans, lamp, or other functionality ............................ 2-12
Lamp does not strike ..................................................................................................... 2-13
Lamp shuts off .............................................................................................................. 2-13
Fixture is not responding to control commands—“Recv” LED does not flash ............ 2-14
Control commands pass-through only, lamp and fans work only in self-test ............... 2-14
Dim flags close, fixture does not respond to control commands, lamp turns off,
fans turn off .................................................................................................... 2-15
Motor or mirror does not move smoothly ..................................................................... 2-15
Color wheel or static litho wheel is not centered in the beam or is in the wrong
position ............................................................................................................ 2-16
Lithos or dichroic filters are cracking ........................................................................... 2-16
Color flags, iris or other components cracked or heat damaged ................................... 2-16
Fixture will not accept software upload ........................................................................ 2-17
Low light output, fuzzy images ..................................................................................... 2-17
Fixture does not work: no LEDs, fans, lamp, or other functionality
Possible causes and solutions:
1.
Cause: No input power.
Solutions: Do both of the following:
2.
a.
Verify the fixture is plugged into a working power supply.
b.
Verify the integrity of the power cord and the wiring of the power cord cap.
c.
Make sure the lamp box access door is securely fastened; this engages an
interlock switch which must be engaged for the fixture to power up. The location
of the lamp box access door is shown in Figure 1-14 on page 1-20.
Cause: Power supply board fuse F1 has failed.
Solution: Follow the directions in the section titled “Replacing Power Supply Fuses”
on page 3-15 to inspect and replace the fuse if necessary.
2-12 Cyberlight User Manual
Lamp does not strike
Possible causes and solutions:
1.
Cause: Bad lamp.
Solution: Replace with a new or known good lamp.
2.
Cause: Improper voltage setting or power cord cap wiring.
Solutions: Do both of the following:
3.
a.
Make sure the fixture is set for the same voltage as the power supply. See
“Setting the Cyberlight® Fixture Voltage” on page 1-10.
b.
Make sure the power cord cap is wired correctly. See “Obtaining and Installing
the Power Cord Cap” on page 1-9.
Cause: Power supply fuse F2 has failed. (Other symptoms are: the fans won’t work
and control commands fail.)
Solution: Follow the instructions in the section titled “Replacing Power Supply
Fuses” on page 3-15 to inspect the fuse and replace it if necessary.
Lamp shuts off
Possible causes and solutions:
1.
Note
Cause: Over-temperature.
The fixture’s maximum operating temperature is 50° C (122° F). An over-temperature
condition can be confirmed by a rapidly-flashing yellow Lamp LED. The location of rearpanel LEDs is shown in Figure 1-1 on page 1-8.
Solutions: Do all three of the following:
a.
Check for restricted air flow. Clean the fans, especially the fans in the lamp box
access door. The lamp box access door is shown in Figure 1-2 on page 1-11.
Instructions for cleaning the fans are shown in the section titled “Cleaning the
Fans” on page 3-3.
b.
Verify fan power connectors are attached to the power supply board. See
“Setting the Cyberlight® Fixture Voltage” on page 1-10 for instructions on
removing the lamp box access door so you can check fan connections.
c.
Check power supply board fuse F4. Follow the instructions in the section titled
“Replacing Power Supply Fuses” on page 3-15 to inspect the fuse and replace it
if necessary.
Chapter 2 Using Your Cyberlight 2-13
2
2.
Cause: Lamp socket is loose, causing arcing.
Solution: Replace the lamp socket assembly. Call your High End Systems dealer/
distributor for more information.
3.
Cause: Aging lamp.
Solution: Replace with a new or known good lamp.
Fixture is not responding to control commands—“Recv” LED does not flash
Possible causes and solutions:
1.
Cause: Faulty XLR cable.
Solutions: Do one or both of the following:
3.
a.
Replace XLR cables going to the fixture’s Data In and Data Out connectors with
known good cables.
b.
Verify cable integrity using cable test equipment.
Cause: There is no controller attached to the link, or the controller is not generating
any output.
Solution: Verify that a controller is attached to the link. Verify that the controller is
generating output by sending commands to a known working device.
4.
Cause: Power supply fuse F2 has failed. (Other symptoms are: the fans won’t work
and the lamp won’t strike.)
Solution: Follow the instructions in the section titled “Replacing Power Supply
Fuses” on page 3-15 to inspect the fuse and replace it if necessary.
Control commands pass-through only, lamp and fans work only in self-test
Possible cause and solution:
Cause: Power supply board fuse F3 has failed.
Solution: Follow the instructions in the section titled “Replacing Power Supply Fuses” on
page 3-15 to inspect the fuse and replace it if necessary.
2-14 Cyberlight User Manual
Dim flags close, fixture does not respond to control commands, lamp turns off, fans
turn off
Possible causes and solutions:
1.
Cause: Faulty XLR cable.
Solutions: Do one or both of the following:
2.
2
a.
Replace XLR cables going to the fixture’s Data In and Data Out connectors with
known good cables.
b.
Verify cable integrity using cable test equipment.
Cause: Power supply board fuse F2 has failed.
Solution: Follow the instructions in the section titled “Replacing Power Supply
Fuses” on page 3-15 to inspect the fuse and replace it if necessary.
Motor or mirror does not move smoothly
Possible causes and solutions:
1.
Cause: Faulty or exposed wiring.
Solutions: Do both of the following:
2.
a.
Make sure there are no exposed wires leading to the motor/mirror. Exposed
wires contacting the metal chassis can short the power supply to the motor/
mirror.
b.
Verify wiring integrity using electrical test equipment.
Cause: Mechanical binding.
Solutions: Do both of the following:
Warning
a.
Manually rotate all wheels (static litho, rotating litho, color and effects) and note
any contact with adjacent wheels. If there is contact, see the section titled
“Checking and Correcting Wheel Clearances” on page 2-18.
b.
Static litho wheel or color wheel: make sure the wheel is not rubbing against its
sensor (the sensor is located at the bottom of the wheel against the chassis). If
there is contact, see “Checking and Correcting Wheel Clearances” on page 2-18.
Contact between wheels within the Cyberlight fixture can result in
damage to fixture components and to the fixture itself!
Chapter 2 Using Your Cyberlight 2-15
Color wheel or static litho wheel is not centered in the beam or is in the wrong
position
Possible causes and solutions:
1.
Cause: Wheel is rubbing against its sensor.
Solution: Manually rotate the wheel and note any contact between the wheel and its
sensor (the sensor is located at the bottom of the wheel against the chassis). If there is
contact, see the section titled “Checking and Correcting Wheel Clearances” on page
2-18.
2.
Cause: Sensor or homing slot is dirty.
Solution: Clean the sensor and the homing slot. See “Cleaning the Color Wheel,
Static Litho Wheel, Effects Wheel and Sensors” on page 3-7.
Lithos or dichroic filters are cracking
Possible causes and solutions:
1.
Cause: Improper installation.
Solution:
2.
•
Static lithos and color wheel dichroic filters: dichroic filters should be oriented
with the coated side facing toward the lamp and the glass (uncoated) side facing
away from the lamp. Lithos should be oriented with the coated side facing away
from the lamp and the glass (uncoated) side facing toward the lamp.
•
Rotating litho wheel lithos: see “Removing and Installing Rotating Lithos” on
page 3-19.
Cause: Faulty infrared filter allowing overheating inside the fixture.
Solution: Visually inspect the infrared filter for cracks or deep scratches. The section
titled “Cleaning the Infrared Filter, Reflector, Color Mixing Flags and Dim Flags” on
page 3-10 shows the location of the infrared filter and how to access it.
Color flags, iris or other components cracked or heat damaged
Possible cause and solution:
Cause: Faulty infrared filter allowing overheating inside the fixture.
Solution: Visually inspect the infrared filter for cracks or deep scratches. The section
titled “Cleaning the Infrared Filter, Reflector, Color Mixing Flags and Dim Flags” on page
3-10 shows the location of the infrared filter and how to access it.
2-16 Cyberlight User Manual
Fixture will not accept software upload
Possible causes and solutions:
1.
Cause: Incorrect addressing or configuration.
Solutions: Do both of the following:
Note
a.
Make sure each fixture is set for a unique fixture number.
b.
Verify that all fixture numbers called for are being used.
The section titled “Setting the Address DIP Switches” on page 2-4 has more information
about fixture addressing.
2.
Cause: No return communication.
Solution: Make sure you bypass any data distributors. Data distributors stop the twoway communication required for software uploads. AF1000 fixtures, Intellabeam
fixtures or Emulator fixtures on the same link as the Cyberlight can also prevent
return communication from Cyberlight. See the section titled “Controlling Multiple
High End Systems Fixtures on the Same Link” on page 2-3 for more information.
Low light output, fuzzy images
Possible causes and solutions:
1.
Cause: Aging lamp.
Solution: Replace the lamp with a new or known good lamp.
2.
Cause: The lamp has not been optimized.
Solution: Optimize the lamp as shown in the section titled “Optimizing the
Cyberlight Fixture Lamp” on page 1-18.
3.
Cause: Dirty optical path.
Solution: Clean all lenses, filters, lithos, the anti-reflective glass and the mirror as
shown in the sections titled “Cleaning the Color Wheel, Static Litho Wheel, Effects
Wheel and Sensors” on page 3-7 and “Cleaning the Infrared Filter, Reflector, Color
Mixing Flags and Dim Flags” on page 3-10.
Chapter 2 Using Your Cyberlight 2-17
2
Checking and Correcting Wheel Clearances
You will need:
- 1/16 inch right angle allen wrench
- 7/16 inch wrench
- 5/64 inch allen wrench
Use the procedure in this section to check for clearances between wheels and their sensors, or
between wheels and other objects in the Cyberlight fixture.
1.
Manually turn the color wheel and effects wheel to make sure there is no contact between them
and any other object.
2.
If there was any contact, adjust the wheel’s clearance by taking the three actions below:
•
using a 1/16 inch right angle allen wrench, loosen the two hex screws on the wheel’s hub
(the rotating litho wheel is shown in Figure 2-7)
•
press on the center of the wheel to move the hub until there is no longer any contact
between the wheel and its sensor or any other object in the fixture
•
retighten the screws
Figure 2-7. Loosening the hub screws allows you to adjust the wheel’s clearance.
2-18 Cyberlight User Manual
3.
Repeat Step 2 to adjust clearances for the color wheel and effects wheel. Make note of the
following:
•
•
4.
5.
If you cannot adjust the wheel to eliminate contact between the wheel and other objects or
its sensor, the wheel might be warped. Follow the directions in the section titled
“Cleaning the Color Wheel, Static Litho Wheel, Effects Wheel and Sensors” on page 3-7
to remove the wheel. After removing the wheel, lay it on a flat surface to determine
whether it is warped. If the wheel is warped, it should be replaced. Contact Customer
Service in one of the ways listed in the section titled “Getting Help” on page Intro-4 for
more information.
The rest of the procedure applies to the rotating litho wheel only.
Do both of the following:
•
Gently rock the rotating litho wheel back and forth and note any contact between the
rotating litho wheel and the static litho wheel.
•
Rotate a litho holder 360°, making note of any contact between it and any other object.
If you observe any contact between an individual rotating litho or the rotating litho wheel and
any other object, adjust the rotating litho wheel hub to eliminate that contact. Loosen the two
1/16 inch allen screws shown in Figure 2-8 below and push on the center of the wheel to
eliminate the contact.
Figure 2-8. Loosen these two allen screws to adjust the rotating litho wheel.
6.
Make sure the white spring plunger still makes contact with the rotating litho wheel. The
location of the spring plunger is shown in Figure 2-9.
Figure 2-9. The rotating litho wheel’s spring plunger must always contact the rotating
litho wheel.
Chapter 2 Using Your Cyberlight 2-19
2
7.
8.
If the spring plunger does contact the rotating litho wheel, proceed with Step 8. Otherwise, do
the following:
•
Use a 7/16 inch wrench to loosen the hex nut shown in Figure 2-9.
•
Use a 5/64 inch allen wrench to turn the allen screw shown in Figure 2-9. This allen screw
moves the spring plunger in and out. Adjust the plunger so that it makes contact with the
rotating litho wheel.
•
Use a 7/16 inch wrench to retighten the hex nut.
Repeat Steps 4 through 7 until you are sure there is no contact between either the rotating litho
wheel or an individual rotating litho and any other object in the fixture.
Note
2-20 Cyberlight User Manual
You can turn the rotating litho wheel until both the wheel and the lithos are locked in place
(they will not move). This is the normal “homed” position of the wheel.
Chapter 3
Servicing Your Cyberlight ®
General Maintenance and Cleaning ............................................................................................... 3-2
Cleaning the Outer Surfaces........................................................................................................... 3-2
Cleaning the Fans ........................................................................................................................... 3-2
Cleaning the Internal Components.......................................................................................... 3-4
Removing the Center Access Door.................................................................................. 3-4
Cleaning the Mirror, Lenses, Motors and Iris.................................................................. 3-4
Cleaning the Color Wheel, Static Litho Wheel, Effects Wheel and Sensors .................. 3-7
Cleaning the Infrared Filter, Reflector, Color Mixing Flags and Dim Flags................. 3-10
Removing and Cleaning the Rotating Lithos................................................................. 3-14
Replacing Parts............................................................................................................................. 3-15
Replacing Power Supply Fuses............................................................................................. 3-15
Removing and Installing Rotating Lithos ............................................................................. 3-19
Removing a Litho from the Rotating Litho Wheel........................................................ 3-19
Replacing Dichroics/Lithos in the Color Wheel or the Static Litho Wheel.......................... 3-22
Adjustments................................................................................................................................. 3-23
Adjusting the Mechanical Zoom Lens (CX Only)................................................................ 3-23
Adjusting the Mirror Head Deviation ................................................................................... 3-24
Adjusting the Yoke Deviation............................................................................................... 3-26
Chapter 3 Servicing Your Cyberlight
3
3-1
General Maintenance and Cleaning
You should clean your Cyberlight after each lamp change to maintain performance and reliability,
since dust and dirt can accumulate and cause overheating or malfunctions.
Warning
Before performing any service or maintenance, make note of the
following:
(1) Hot lamp may be an explosion hazard. Do not open for 5 minutes
after switching off. Wear eye and hand protection when re-lamping.
(2) Equipment surfaces may reach temperatures up to 62° C (144° F).
Allow 10 minutes for cooling before handling.
(3) Disconnect power before re-lamping or servicing.
After allowing the fixture to cool down and powering it off, see one of the topics listed below:
•
•
•
•
3-2
Cyberlight User Manual
“Cleaning the Fans” on page 3-3
“Cleaning the Mirror, Lenses, Motors and Iris” on page 3-4
“Cleaning the Color Wheel, Static Litho Wheel, Effects Wheel and Sensors” on page 3-7
“Cleaning the Infrared Filter, Reflector, Color Mixing Flags and Dim Flags” on page 3-10
Cleaning the Outer Surfaces
Wipe the outer surfaces with a soft cloth or use a vacuum to remove the built-up dust and dirt.
Cleaning the Fans
If necessary to remove built-up dust and dirt from the fans, you can use a low-pressure compressed
air source to clean them. You must place an object (not your fingers!), such as a pen or a
screwdriver, into the fan fins to prevent the fans from spinning while you are blowing air into them;
allowing the fans to spin can result in severe damage to the fans.
3
You must also observe the Caution and Warnings below:
Caution
Make sure the fans are held stationary. The fans can be severely
damaged if they are allowed to spin with the force of the compressed air.
Warnings (1) Use only a low-pressure compressed air source (25 psi or lower).
(2) To avoid personal injury, do not expose your eyes or skin to the direct
jet of compressed air, since it can constitute a serious health hazard. Use
suitable protection for your eyes and exposed skin.
Screwdriver
holding fins in
place
Fan Fins
Compressed
air source
Figure 3-1. Holding the fan fins in place while you clean the fans using compressed
air.
Chapter 3 Servicing Your Cyberlight
3-3
Cleaning the Internal Components
You will need:
- a soft, lint-free cotton cloth
- mild glass cleaning solution
- warm soapy water
Removing the Center Access Door
With the fixture bottom-side up, remove the center access door by sliding the two door thumb
latches inward. Lift the door straight up, unhook the safety chain, and set it aside.
Figure 3-1 . Bottom view of the Cyberlight fixture.
Cleaning the Mirror, Lenses, Motors and Iris
1.
Using a soft, lint-free cotton cloth, remove dirt and dust from the motors, mirror, power lens,
focus lens, and zoom lens. If necessary to remove built-up dirt and dust, clean the lenses with
a mild glass cleaner and a soft lint-free cotton cloth.
Note
2.
3-4
Cyberlight User Manual
The Cyberlight CX has no color mixing flags, motorized zoom lens, or frost flags. It does
have a three-position mechanical zoom lens.
Clean the mirror with a cloth soaked in warm, soapy water (see Figure 3-2 for the location of
the mirror).
3
Figure 3-2. Locations of the iris, power lens, focusing lens, zoom lens and mirror.
Figure 3-3. Locations of the motors.
3.
Manually turn the rotating litho wheel until its open position is opposite the iris. (You will see
the iris when looking toward the focusing lens through the open position on the rotating litho
wheel.)
Chapter 3 Servicing Your Cyberlight
3-5
4.
Manually close the iris by turning the large black-colored gear shown in Figure 3-4:
Figure 3-4. Close the iris by rotating the large black gear located on top of the iris
motor.
5.
Gently wipe away excess dust and dirt from the iris using a soft lint-free cloth. You can access
one side of the iris through the open position on the rotating litho wheel; you can access the
other side through the open position on the effects wheel.
Caution
6.
Be careful when cleaning the iris. It is made of a very thin, delicate metal
that can be easily damaged.
Clean both sides of the anti-reflective glass (shown in Figure 3-5) with a soft, lint-free cotton
cloth and mild glass cleaning solution.
Anti-reflective glass
cy b er lig h t
AU STIN, TE XAS U .S.A.
R
LITH O
L IGH TWAV E R ESEA RCH
Figure 3-5. Cleaning the anti-reflective glass.
3-6
Cyberlight User Manual
Cleaning the Color Wheel, Static Litho Wheel, Effects Wheel and Sensors
You will need:
- one 9/64 inch right angle allen wrench
- one 5/16 inch wrench
Use this procedure to remove and clean the color wheel, static litho wheel, and effects wheel; and to
clean the sensors for the color wheel and the static litho wheel. High End Systems recommends
removing the wheels for cleaning to prevent bending or deforming them.
The optical sensors, located below the color and litho wheels, electronically sense the homing slot
on the edge of the wheel in order to keep track of the “home” positions of the respective wheels.
1.
This step applies to removing the static litho wheel only. Manually rotate the color wheel until
the open position is opposite the standoff you will remove next. The location of the standoff is
shown in Figure 3-6.
3
Figure 3-6. Removing the standoff between the iris motor and the color wheel.
2.
This step applies to removing the static litho wheel only. Use a 9/64 inch right angle allen
wrench to remove the two screws holding the standoff between the rotating litho assembly and
the color wheel assembly. (You will need to insert the allen wrench through the open position
on the color wheel in order to remove one of the screws.) Set the standoff aside.
3.
Manually rotate the wheel until the large ends of the keyhole slots are facing down as shown in
Figure 3-7.
Figure 3-7. Make sure the wheel is positioned with the keyhole slots facing downward
before removing it.
Chapter 3 Servicing Your Cyberlight
3-7
4.
Holding the wheel in place with one hand, use a 5/16 inch wrench to loosen (do not remove)
the two hex screws securing the wheel to its hub.
5.
Pull up on the wheel to remove it from the hub. The large ends of the keyhole slots will slip
over the two hex screws.
6.
Clean the wheel with a mild glass cleaner and a soft cotton cloth. Make sure the homing slot
(shown in Figure 3-8) is free of dust and dirt.
Figure 3-8. The homing slot is a small groove on the outside edge of the wheel. The
static litho wheel and the color wheel’s homing slots are in different locations. The
effects wheel does not have a homing slot.
7.
This step applies to the color wheel and static litho wheel only. Clean the groove in the wheel
sensor. Figure 3-9 shows the location of the static litho wheel sensor. The color wheel has an
identical sensor located underneath it.
Figure 3-9. Clean the groove in the wheel sensor.
8.
3-8
Cyberlight User Manual
When you are finished cleaning the wheel and sensor, carefully slip the wheel back onto its
hub. The large ends of the keyhole slots should be pointing down, which allows them to slip
over the tops of the screws which secure the wheel to the hub. Make sure of the following:
•
All but the effects wheel: The wheel fits within the sensor slot, not outside of the slot.
•
Static litho wheel: Orient the coated/etched side of the litho away from the lamp; orient the
glass side of the litho toward the lamp. Improper installation can damage the litho.
3
Figure 3-10. Static litho wheel lithos must be oriented with the coated/etched side
facing away from the lamp.
•
Color wheel: Orient the coated side of the color wheel dichroic filter toward the lamp;
orient the glass side of the dichroic away from the lamp.
Figure 3-11. Color wheel dichroic filters should be oriented with the coated side of the
dichroic facing toward the lamp and the glass side facing toward the static litho
wheel.
Also make sure you do the following:
•
Place the “slider” screw on the hub in the center of the middle keyhole slot, as shown in
Figure 3-12 on page 3-10.
•
Push the wheel until the two hex nuts are all the way onto the narrow ends of the keyhole
slots before tightening the screws.
•
Tighten the hex nuts until they are secure but do not overtighten. Doing so could damage
the wheel.
Caution
Be careful not to allow the lithos/dichroics to contact other objects when
reinstalling the wheels. Doing so could scratch them.
Chapter 3 Servicing Your Cyberlight
3-9
Figure 3-12. Position the keyhole slots so they fit over both hex screws as well as the
“slider” screw inset in the hub.
9.
Retighten the two screws that hold the wheel in place. Tighten the screws only until they are
snug; do not overtighten.
10. Re-install the standoff you removed in Step 1 on page 3-7.
Cleaning the Infrared Filter, Reflector, Color Mixing Flags and Dim Flags
You will need:
- one right angle 5/32 inch allen wrench
This section explains how to clean two components located inside the Cyberlight lamp box: the
infrared filter and reflector. It also explains how to clean the color mixing flags and the dim flags,
which are located on the other side of the lamp assembly.
Cautions
(1) Equipment surfaces may reach temperatures up to 62° C (144° F).
Allow 10 minutes for cooling before handling.
(2) Change shields, lenses, or the infrared filter if they have become
visibly damaged to such an extent that their effectiveness is impaired, for
example by cracks or deep scratches.
Warnings (1) An unshielded MSR/MSD 1200 lamp emits ultraviolet and visible
(UV-vis) radiation which could damage eyes and skin. Never look
directly at the lamp while lamp is on.
(2) Hot lamp may be an explosion hazard. Do not open for 5 minutes
after switching off. Wear eye and hand protection when re-lamping.
1.
3-10 Cyberlight User Manual
Allow the fixture to cool as described above then power it OFF and unplug it from the power
source.
2.
Fully back out the two lamp assembly screws shown in Figure 3-13. The screws have retaining
springs that prevent them from being removed.
3
Figure 3-13. Location of lamp assembly and optimization screws.
3.
Grip the three lamp optimizing screws and pull the lamp assembly straight out of the back of
the fixture. The lamp’s power cord is long enough to allow you to pull the lamp assembly
entirely free of the Cyberlight.
4.
Carefully set the lamp assembly aside. You can remove the lamp, if you wish, and place it
where it will not get broken. Pull it straight out of the socket as shown in Figure 3-14.
Brass socket
Figure 3-14. Removing the lamp from its brass socket.
5.
Using the 5/32 inch right angle allen wrench, remove the four 5/32 inch allen screws shown in
Figure 3-15.
Chapter 3 Servicing Your Cyberlight 3-11
Figure 3-15. Location of the first four rear panel screws you need to remove in order
to access the lamp assembly.
6.
Remove the last two 5/32 inch allen head screws from the color mixing plate as shown in
Figure 3-16. Carefully lift the lamp box access door from the fixture.
Remove these two 5/32 inch allen screws
Color mixing plate
Figure 3-16. In order to remove the lamp box access door, you need to remove the
last two 5/32 inch allen screws, which are located by the color mixing and dim flags.
7.
3-12 Cyberlight User Manual
CL and CX models only: As you lift the assembly, disconnect the two fan power connectors
(black and red wires) from the power supply board as shown in Figure 3-17. Set the lamp box
access door aside.
Figure 3-17. On CL and CX models, make sure you disconnect the fan power wires
from the fan connectors before removing the lamp box access door.
8.
3
Using a lint-free cotton cloth and mild glass cleaner, wipe dust and dirt from the reflector and
infrared filter, which are shown in Figure 3-18. The infrared filter consists of two rose-colored
glass hemispheres directly in front of the reflector.
Figure 3-18. Locations of the reflector and infrared filter.
9.
Using a soft, lint-free cotton cloth, wipe excess dirt and dust from the other side of the infrared
filter and from the dim flags. There are two black, metallic dim flags on all Cyberlight models.
Their locations are described below:
•
If you have the CL or SV, the two dim flags are among the color mixing flags, so you
should clean all the flags at the same time. Manually “flip” each flag until it is in a
position where you can access it, then wipe the flag with a lint-free cloth. Dampen the
cloth with a mild glass cleaning solution if necessary to clean built-up dust and dirt. If a
color mixing flag is damaged or broken, or if you need to remove it in order to clean it,
contact Customer Service in one of the ways shown in the section titled “Getting Help” on
page Intro-4.
Chapter 3 Servicing Your Cyberlight 3-13
•
The CX has no color mixing flags. The two dim flags are located in the area shown in
Figure 3-19.
Figure 3-19. Location of the color mixing flags and dim flags.
10. Make sure the infrared filter, reflector, color mixing flags and dim flags are all clean.
11. Carefully guide the lamp assembly straight back into the fixture and make sure the lamp is
inserted into the reflector. Be careful not to crimp the two lamp wires as you insert the lamp
assembly. Firmly tighten the two lamp assembly screws (refer to Figure 3-13 on page 3-11) to
secure the assembly to the fixture.
12. Reinstall the lamp assembly cover. Do the following:
•
CL and CX only: Reconnect the two fan wires to the Cyberlight power supply board.
Refer back to Figure 3-17 on page 3-13.
•
Carefully replace the lamp box access door.
•
Reinstall the six 5/32 inch screws (refer to Figure 3-15 on page 3-12 and Figure 3-16 on
page 3-12).
Removing and Cleaning the Rotating Lithos
You can clean the rotating lithos in or out of the rotating litho wheel using a mild glass cleaner and
a soft cotton cloth. Turn the rotating wheel so that you have easy access to the litho then clean the
lithos while they are still mounted in the wheel.
If you wish to remove the litho for cleaning follow the procedure in the section titled “Removing
and Installing Rotating Lithos”. Then clean the litho with a mild glass cleaner and a soft lint free
cloth.
3-14 Cyberlight User Manual
Replacing Parts
This section explains how to remove and replace parts inside the fixture. Make note of the
following caution and warnings:
Caution
Equipment surfaces may reach temperatures up to 62° C (144° F). Allow
10 minutes for cooling before handling.
Warnings (1) An unshielded MSR/MSD 1200 lamp emits ultraviolet and visible
(UV-vis) radiation which could damage eyes and skin. Never look
directly at the lamp while lamp is on.
3
(2) Hot lamp may be an explosion hazard. Do not open for 5 minutes
after switching off. Wear eye and hand protection when re-lamping.
(3) Replace fuses only with the specified type and rating.
(4) Disconnect power before re-lamping or servicing.
After allowing the fixture to cool as described above, turn it OFF and unplug it from its power
source. Then see one of the following sections:
•
•
•
•
•
•
“Replacing Power Supply Fuses” on page 3-15
“Removing and Installing Rotating Lithos” on page 3-19
“Replacing Dichroics/Lithos in the Color Wheel or the Static Litho Wheel” on page 3-22
“Adjusting the Mechanical Zoom Lens (CX Only)” on page 3-23
“Adjusting the Mirror Head Deviation” on page 3-24
“Adjusting the Yoke Deviation” on page 3-26
Replacing Power Supply Fuses
This section explains how to replace the four fuses located on the Cyberlight power supply board.
You will need:
- 5/32 inch allen wrench
- Replacement fuses (5 mm by 20 mm only).
There are a total of four:
Amps
Volts
Fuse Type
2.5 A
250 V
Slow Blow Only
4A
250 V
Fast Blow Only
0.5 A
250 V
Fast Blow Only
1.6 A
250 V
Fast Blow Only
Chapter 3 Servicing Your Cyberlight 3-15
1.
After allowing the fixture to cool as described on the previous page, turn the power switch OFF
and unplug the fixture.
2.
With the fixture oriented bottom-side up, remove the center access door by sliding the two door
latches inward. Lift the door straight up, unhook the safety chain, and set the door aside. See
Figure 3-20.
Figure 3-20. View of the bottom of the Cyberlight fixture, where the access door
latches are located.
3.
Remove the fixture’s lamp box access door by removing the six 5/32 inch allen head screws
securing it to the fixture as follows:
•
Remove the four 5/32 inch allen head screws from the bottom of the rear panel as shown in
Figure 3-21.
Figure 3-21. Removing the rear panel screws allows you to access the Cyberlight
voltage selection jumpers.
3-16 Cyberlight User Manual
•
Remove the last two 5/32 inch allen head screws from the color mixing plate as shown in
Figure 3-22. Carefully lift the lamp box access door from the fixture.
Remove these two 5/32 inch allen screws
Color mixing plate
3
Figure 3-22. In order to remove the lamp box access door, you need to remove the
last two 5/32 inch allen screws, which are located by the color mixing and dim flags.
4.
CL and CX models only: As you lift the assembly, disconnect the two fan wiring harness
connectors (black and red wires) from the power supply board as shown in Figure 3-23. Set
the lamp box access door aside. You now have access to the power supply board.
Figure 3-23. On CL and CX models, make sure you disconnect the fan power wires
from the fan connectors before removing the lamp box access door.
Chapter 3 Servicing Your Cyberlight 3-17
5.
Note which fuse(s) needs to be replaced and make sure you replace it with a fuse of the same
type and rating, as shown in the list below:
F1 = 2.5 A, 250 V, Slow Blow Only
F2 = 4 A, 250 V, Fast Blow Only
F3 = 0.5 A, 250 V, Fast Blow Only
F4 = 1.6 A, 250 V, Fast Blow Only
}
5 mm x 20 mm only
Table 3-1 below describes the function of each of the four power supply board fuses.
Table 3-1: Description and Function of Power Supply Board Fuses
Fuse
Type and
Rating
Protects
Symptom
F1
2.5 A, 250 V
Input transformer
Fixture stops working; no
functionality.
F2
4 A, 250 V
All 5 V power
supplies
Fans won’t work, control
commands fail, lamp won’t strike.
F3
0.5 A, 250 V
Data link power
supply
Control commands pass-through
only, lamp and fans work only in
self-test.
F4
1.6 A, 250 V
Fans
Fans won’t work, forcing fixture
into thermal shutdown.
Fuses F1, F2 and F3 are located on either side of the large green-colored earth wire. Figure 3-24
shows the location of each fuse.
Figure 3-24. Location of power supply board fuses.
6.
3-18 Cyberlight User Manual
Replace the lamp box access door by reversing this procedure and power the fixture ON.
Removing and Installing Rotating Lithos
This section explains how to remove and replace LithoPatterns lithos.
Please heed the following precautions when handling and using lithos:
•
Avoid touching the coated side of the glass. Handle the edge or uncoated side
of the glass when removing or installing lithos. If possible, wear cloth gloves
when inserting and removing lithos from the litho wheel housing.
•
If necessary, clean the lithos with a mild glass cleaner and a soft cloth.
3
Removing a Litho from the Rotating Litho Wheel
1.
Remove the fixture’s center access door as shown in Figure 3-25.
Figure 3-25. Removing the center access door.
2.
Rotate the wheel until the desired litho is in a position for easy access.
3.
Keep the rotating litho holder in place with one hand and grasp the spring tab with the other
hand. Turn the spring; as you do so pull it away from each retainer washer. Continue pulling
and turning the spring until it is loose enough to lift out of the housing.
4.
Carefully remove the litho from the housing.
Chapter 3 Servicing Your Cyberlight 3-19
5.
Insert the new or cleaned litho into the litho housing as shown in Figure 3-26. Make sure you
orient the litho as explained below:
•
Any LithoPatterns or any Psy-Dye lithos, including Psy-Dye Special Effects: the
coated side of the litho must face away from the lamp; uncoated (glass) side faces toward
the lamp.
•
Flat unglazed Art Glass or Special Effects other than Psy-Dye: the non-textured side
must face away from the lamp; textured side faces toward the lamp.
•
Multi-Color lithos with stainless steel holder: the solid flat side of the stainless steel
litho holder must face away from the lamp (i.e., the flat side of the holder must be against
the wheel hub).
Caution
Improper installation can result in heat damage to the litho. Use care
when installing the litho; make sure you handle it by the edge only and do
not allow it to contact any other object in the fixture while you are
inserting it.
Toward lamp
Away from lamp
Side view of
rotating litho
housing
Figure 3-26. Insert the new or cleaned litho into the rotating litho housing as
described above; improper installation can cause heat damage to the litho.
6.
Insert the spring into the housing as shown in Figure 3-27.
Turn the spring as you push in on it
Figure 3-27. Turn on the spring as you push it into the rotating litho housing.
7.
3-20 Cyberlight User Manual
To lock the litho in place, begin working the spring under any one of the three retainer washers
until the spring is fully compressed as shown in Figure 3-28. (The retaining washers are
shaded in the figure.)
Side view of
rotating litho
housing
Fit the end of the
spring under the washer
3
Front view of
rotating litho
housing
Figure 3-28. Make sure the end of the spring fits under any one of the three retaining
washers, as shown above.
Caution
Do not place the end of the spring anywhere else in the rotating litho
wheel housing, as shown in Figure 3-29. Doing so could cause the spring
to unwind and/or cause it to come into contact with other objects inside
the fixture, possibly resulting in damage to the fixture.
Incorrect placement
Figure 3-29. Do not place the end of the spring between the three retaining washers.
Chapter 3 Servicing Your Cyberlight 3-21
Replacing Dichroics/Lithos in the Color Wheel or the Static
Litho Wheel
This section explains how to replace dichroic filters in the color wheel and how to replace lithos in
the static litho wheel. (A dichroic is solid-colored with no etched pattern, while a litho has an
etched pattern.)
Although the lithos and dichroics look different from each other, they are the same size and the
wheels are the same size, so the procedure for replacing them is exactly the same.
You can replace dichroics/lithos if they are damaged or broken, to change the order in their
respective wheels, or to add new ones. (See the section titled “Optional Accessories” on page 1-7
for ordering information.) Dichroics and lithos are also completely interchangeable between
Cyberlight CLs, CXs and SVs.
1.
Position the wheel so the dichroic/litho you wish to replace is easy to access.
2.
This step applies to replacing a litho only. Position the effects wheel so the open position in
the wheel aligns with the litho you wish to replace.
3.
Push the dichroic/litho you wish to replace toward the center of the wheel to free it from the
two wheel tabs as shown in Figure 3-30.
Figure 3-30. Push the dichroic/litho toward the large retaining tab to free it from the
wheel tabs.
4.
Once the dichroic/litho is free of the two wheel tabs, pull it out of the wheel. If you intend to
reuse this dichroic/litho, put it in a safe place where it will not get scratched.
5.
Color wheel only: Orient the dichroic filter so the coated side is facing toward the lamp and
the uncoated, glass side is facing toward the static litho wheel.
6.
Static litho wheel only: Orient the new litho so the etched side is facing away from the lamp
(toward the effects wheel). The glass side must be facing the lamp. Improper installation can
damage the litho.
7.
Install the new dichroic/litho into its wheel by pushing it under the large retaining clip, then
pull it up so it fits under the wheel tabs.
3-22 Cyberlight User Manual
Adjustments
This section explains the Cyberlight CL, SV and CX fixture adjustments.
You will need:
- #2 Phillips screwdriver
- 9/64 inch allen wrench
Adjusting the Mechanical Zoom Lens (CX Only)
You can easily position the mechanical zoom lens to any of three zoom values:
Forward (position 1) is: ~ 12°
Middle (position 2) is: ~ 14°
Rear (position 3) is: ~ 18°
1.
Optional: Remove the front fan access door for easier access to the lens assembly. Remove
the four screws that fasten the fan assembly to the front plate with a #2 Phillips screwdriver.
Also remove the 9/64 inch allen head screw from each side of the fan assembly. Lift the fan
assembly out far enough to access the fan wires connector. Separate the connector and set the
fan assembly aside.
2.
The zoom lens assembly is fastened to the slide by two Phillips head screws. Remove the two
screws, move the lens to desired position (1, 2, or 3), then, re-insert and tighten the two screws.
3
Position 3 = ~18o
Position 2 = ~14o (factory default)
Position 1 = ~12o
Remove these two
Phillips-head screws
Figure 3-31. Adjusting the Cyberlight CX mechanical zoom lens.
Chapter 3 Servicing Your Cyberlight 3-23
Adjusting the Mirror Head Deviation
You will need:
- 5/32 inch right angle allen wrench
You can easily pivot or offset the mirror head deviation up to 20 degrees left or right of center for a
total range of 40 degrees.
1.
Using an allen wrench, loosen the three 5/32 inch allen screws shown in Figure 3-32. Using
your hand, loosen T-handle that locks the mirror head in position.
Loosen these 5/32" allen screws
Loosen this T-handle
Figure 3-32. Loosen the three 5/32 inch allen screws and the T-handle to adjust the
mirror head deviation.
Note
2.
3-24 Cyberlight User Manual
The mirror head deviation adjustment can be performed with the Cyberlight positioned
either on its back (as is shown in Figure 3-32) or on its front.
Grasp both sides of the mirror head and rotate it until it is positioned according to your needs.
See Figure 3-33.
3
Figure 3-33. Grasp both sides of the mirror head and rotate it to the desired position.
Note the “Deviation” angle (see Figure 3-34) you are using, in case you wish to use the same
deviation in other venues.
-
+
gre
de
es
de
gr
ee
s
3.
Figure 3-34. Be sure to note the deviation angle in case you need to set other
fixtures for the same deviation, or if you want to use this exact deviation again. For
example, the figure above has about a 10° + (plus) deviation.
4.
When you are finished, retighten the three 5/32 inch allen screws and the T-handle so the
mirror head is securely in position.
Chapter 3 Servicing Your Cyberlight 3-25
Adjusting the Yoke Deviation
You can adjust the yoke deviation to orient the Cyberlight in different positions. If you make note
of the deviation angle, you can orient a group of Cyberlight fixtures in precisely the same direction.
Figure 3-35 below shows how to adjust the yoke deviation.
Figure 3-35. Adjust the yoke handles on both sides of the Cyberlight to tilt the fixture
in a specific way.
3-26 Cyberlight User Manual
Appendix A
DMX Control of Cyberlight®
Use this appendix to control your Cyberlight fixtures using DMX 512 modes 1, 2, and 3.
Overview
The Cyberlight is a block-addressed fixture; that is, you do not address it at an arbitrary DMX start channel,
but rather at a channel boundary. There are two channel boundaries you can select: 15-channel and 20channel. If you choose to control your Cyberlight on a 20-channel boundary, for example, each fixture takes
up a contiguous block of 20 DMX channels.
Selecting a DMX Mode
A
The three DMX modes available for your Cyberlight provide three different levels of control and flexibility,
and can be used with CLs, SVs, and CXs as summarized below:
•
Mode 1: standard 20-channel control.
•
Mode 2 (recommended): enhanced 20-channel control. Mode 2 offers the same features as mode 1 but
at greater resolution (for example, mode 2 supports frost strobing and 96 shutter strobe speeds while
mode 1 does not support frost strobing and supports only eight shutter strobe speeds).
•
Mode 3: minimal 15-channel minimal control. Mode 3 does not support color mixing or zoom. You
can select mode 3 in two possible situations:
•
You are controlling only CXs on a link. Mode 3 utilizes all CX features but does not support color
mixing or zoom, which are supported by CLs and SVs only.
•
You have do not have enough available DMX channels on the link to allocate 20 channels per
Cyberlight fixture. (Mode 3 also supports up to 34 fixtures per link, while modes 1 and 2 both
support up to 25 fixtures per link.)
Note
Modes 1, 2 and 3 are supported by all Cyberlight models. If you have any Cyberlight CXs on the
link, they will not respond to color mixing or zoom commands, but will otherwise respond to
commands identically to CLs and SVs.
Performing Software Uploads Over a Link
Software uploads can be performed over a link using either a Link Card or the Cyberlight Upload Module.
Fixtures automatically switch to LWR protocol for the upload, then switch back to DMX control after the
upload has been successfully completed. Consult the Status Cue software documentation or the Upload
Module for the procedure.
Note
There are two things that can stop software uploads to a Cyberlight: a data distributor and certain
High End Systems equipment on the same link. You must bypass any data distributors when
performing a software upload on a link. Also review the section titled “Controlling Multiple High
End Systems Fixtures on the Same Link” on page 2-3.
Appendix A DMX Control of Cyberlight
A-1
Address DIP Switches
Figure A-1 below shows a functional breakdown of the eight DMX address DIP switches, located on the
Cyberlight fixture’s rear panel. (Review “Identifying Rear Panel Components” on page 1-8 for the location
of the switches).
Figure A-1. The DMX address switch block allows you to select the control protocol (DMX 1, DMX
2, DMX 3, or LWR) and the fixture number.
Related Topics
Other information you might need to reference when assigning DMX channel numbers is summarized
below:
•
The section titled “Channel Boundaries” on page A-18 explains the relationship between fixture number
(which you set with the address DIP switches) and actual DMX address ranges.
•
The section titled “Choosing DMX 512 or LWR Protocol” on page 2-2 explains what to consider before
selecting either DMX 512 or Lightwave Research (LWR) control protocol.
•
The section titled “Controlling Multiple High End Systems Fixtures on the Same Link” on page 2-3
explains important considerations when mixing Cyberlight fixtures, Intellabeam fixtures, Emulator
fixtures, and AF1000 fixtures on the same link.
Accessing Control Information
In order to access the control channel (channel 20 in 20-channel DMX modes 1 and 2 and channel 15 in 15channel DMX mode 3), you must follow the procedure below:
1.
Put the dim channel and the control channel at full.
2.
Put the dim channel at zero and the control channel at full.
3.
(Must occur within 3 seconds): Put the dim channel at zero. Put the control channel at: 25% for home
or 50% for shutdown.
4.
Hold for an additional 3 seconds.
Rounding Conventions
The values displayed in the “Range” and “Channel Value” columns in the following tables may vary slightly
depending on your controller’s rounding convention.
A-2
Cyberlight User Manual
DMX 512 Mode 1 – Standard Cyberlight® DMX
Control
Each Cyberlight fixture in DMX mode 1 uses 20 channels of the DMX 512 protocol thus providing control
for up to 25 fixtures (512 / 20 = 25.6 fixtures). Use the procedure below to control your Cyberlight with
DMX mode 1:
1.
Set the fixture to DMX mode 1 by setting address switch 7 to OFF and address switch 8 to ON.
2.
Set address switches 1 through 5 to correspond to the desired fixture number, as shown in Table A-1.
Note that Cyberlight CX fixtures configured for 20-channel mode work properly and can be mixed with
Cyberlight fixtures; they do not respond to the color mixing, zoom, or variable frost constructs.
3.
Refer to Table A-2 for the Cyberlight DMX 20-channel assignments.
Table A-1: Addressing Fixtures in 20-Channel DMX 512 Mode 1
Cyberlight
Fixture
Fixture
Address
Switches ON
Cyberlight
DMX Channel
Number
Fixture
Fixture
Address
Switches ON
A
DMX Channel
Number
Fixture 1
none
001
Fixture 14
1, 3, and 4
261
Fixture 2
1
021
Fixture 15
2, 3, and 4
281
Fixture 3
2
041
Fixture 16
1, 2, 3, and 4
301
Fixture 4
1 and 2
061
Fixture 17
5
321
Fixture 5
3
081
Fixture 18
1 and 5
341
Fixture 6
1 and 3
101
Fixture 19
2 and 5
361
Fixture 7
2 and 3
121
Fixture 20
1, 2, and 5
381
Fixture 8
1, 2, and 3
141
Fixture 21
3 and 5
401
Fixture 9
4
161
Fixture 22
1, 3, and 5
421
Fixture 10
1 and 4
181
Fixture 23
2, 3, and 5
441
Fixture 11
2 and 4
201
Fixture 24
1, 2, 3, and 5
461
Fixture 12
1, 2, and 4
221
Fixture 25
4 and 5
481
Fixture 13
3 and 4
241
Table A-2: Cyberlight DMX Assignments Mode 1
Channel
Assignment
Range
Construct Parameter
Channel 1
Pan coarse adjustment
Position
Channel 2
Pan fine adjustment
Position
Channel 3
Tilt coarse adjustment
Position
Channel 4
Tilt fine adjustment
Position
Appendix A DMX Control of Cyberlight
A-3
Table A-2: Cyberlight DMX Assignments Mode 1
Channel
Channel 5
Assignment
Color Wheel
Range
Full
0
A-4
Construct Parameter
Color 1 (open)
Half color 1 and 2
Color 2
Half color 2 and 3
Color 3
Half color 3 and 4
Color 4
Half color 4 and 5
Color 5
Half color 5 and 6
Color 6
Half color 6 and 7
Color 7
Half color 7 and 8
Color 8
Half color 8 and 1
Forward spin speed 8
Forward spin speed 7
Forward spin speed 6
Forward spin speed 5
Forward spin speed 4
Forward spin speed 3
Forward spin speed 2
Forward spin speed 1
Reverse spin speed 1
Reverse spin speed 2
Reverse spin speed 3
Reverse spin speed 4
Reverse spin speed 5
Reverse spin speed 6
Reverse spin speed 7
Reverse spin speed 8
Color 1 (open)
Channel 6
Cyan (Red)
Color Mix
Channel 7
Magenta (Green)
Color Mix
Channel 8
Yellow (Blue)
Color Mix
Cyberlight User Manual
Table A-2: Cyberlight DMX Assignments Mode 1
Channel
Channel 9
Assignment
Static litho
Range
Full
0
Channel 10
Rotating Litho
Full
Select the litho to rotate
forward/reverse with this
channel. Then use Channel
11 to set the rotation speed.
For rotating litho position
parameters select the litho
position to index with this
channel. Then use Channel
11 to set the rotational
position (index value) from 0
to 360 degrees.
0
Construct Parameter
Litho 1 (open)
Litho 2
Litho 3
Litho 4
Litho 5
Litho 6
Litho 7
Litho 8
Forward spin speed 8
Forward spin speed 7
Forward spin speed 6
Forward spin speed 5
Forward spin speed 4
Forward spin speed 3
Forward spin speed 2
Forward spin speed 1
Reverse spin speed 1
Reverse spin speed 2
Reverse spin speed 3
Reverse spin speed 4
Reverse spin speed 5
Reverse spin speed 6
Reverse spin speed 7
Reverse spin speed 8
Litho 1 (open)
A
Position 3 (open)
Reverse rotate 5
Reverse rotate 4
Reverse rotate 2
Reverse rotate 1
Forward rotate 5
Forward rotate 4
Forward rotate 2
Forward rotate 1
Position 5
Position 4
Position 3 (open)
Position 2
Position 1
Position 3 (open)
Channel 11
Rotate
(use with Channel 10)
For Rotating Litho rotate mode use Ch 11 to set
rotate speed
For Rotating Litho position mode use Ch 11 to set
the index from 0 to 360 degrees
Channel 12
Zoom
Zoom in/out
Channel 13
Focus
Focus in/out
Channel 14
Iris
Iris open/close
Appendix A DMX Control of Cyberlight
A-5
Table A-2: Cyberlight DMX Assignments Mode 1
Channel
Channel 15
Assignment
Effects Wheel
Range
Full
0
Channel 16
Frost
Channel 17
Shutter
Dim
Channel 19
Motor Speed
Channel 20*
Control
Effect 4 (open)
Effect 8
Effect 7
Effect 6
Effect 5
Effect 4
Effect 3
Effect 2
Effect 1
Effect 4 (open)
Frost in/out
Full
0
Channel 18
Construct Parameter
Open
Closed
Strobe speed 8
Strobe speed 7
Strobe speed 6
Strobe speed 5
Strobe speed 4
Strobe speed 3
Strobe speed 2
Strobe speed 1
Open
Closed
Dim open/close
Full
Speed 99
0
Speed 1
Speed 94
50% fader – shutdown
25% fader – home
* - Make sure you first follow the instructions in the section titled “Accessing Control Information” on page A-2.
A-6
Cyberlight User Manual
DMX 512 Mode 2 – Enhanced Cyberlight® DMX
Control
Each Cyberlight fixture in DMX mode 2 uses 20 channels of the DMX 512 protocol thus providing control
for up to 25 fixtures (512 / 20 = 25.6 fixtures). Use the procedure below to control your Cyberlight with
DMX mode 2:
1.
Set the Cyberlight fixture to DMX mode 2 by setting address switch 7 to ON and address switch 8 to
OFF.
2.
Set address switches 1 through 5 to correspond to the desired fixture number, as shown in Table A-3.
Note that Cyberlight CX fixtures configured for 20-channel mode work properly and can be mixed with
Cyberlight fixtures; they do not respond to the color mixing, zoom, and frost constructs.
3.
Refer to Table A-4 for the Cyberlight DMX mode 2 channel assignments.
Table A-3: Addressing Fixtures in 20 Channel DMX 512 Mode 2
Cyberlight
Fixture
Fixture
Address
Switches ON
DMX Channel
Number
Cyberlight
Fixture
Fixture
Address
Switches ON
A
DMX Channel
Number
Fixture 1
none
001
Fixture 14
1, 3, and 4
261
Fixture 2
1
021
Fixture 15
2, 3, and 4
281
Fixture 3
2
041
Fixture 16
1, 2, 3, and 4
301
Fixture 4
1 and 2
061
Fixture 17
5
321
Fixture 5
3
081
Fixture 18
1 and 5
341
Fixture 6
1 and 3
101
Fixture 19
2 and 5
361
Fixture 7
2 and 3
121
Fixture 20
1, 2, and 5
381
Fixture 8
1, 2, and 3
141
Fixture 21
3 and 5
401
Fixture 9
4
161
Fixture 22
1, 3, and 5
421
Fixture 10
1 and 4
181
Fixture 23
2, 3, and 5
441
Fixture 11
2 and 4
201
Fixture 24
1, 2, 3, and 5
461
Fixture 12
1, 2, and 4
221
Fixture 25
4 and 5
481
Fixture 13
3 and 4
241
Appendix A DMX Control of Cyberlight
A-7
The “Channel Value (%)” column in Table A-4 below has values you should use if your controller has
dimmer-type controls. The “Channel Value (numerical)” column has values you should use if you are using
the Status Cue system or another controller that uses digital or numerical controls.
Table A-4: Cyberlight DMX Assignments Mode 2
Channel
Assignment
Channel
Value
(numerical)
Construct Parameter
Channel 1
Pan coarse adjustment
0-100%
0-255
Position
Channel 2
Pan fine adjustment
0-100%
0-255
Position
Channel 3
Tilt coarse adjustment
0-100%
0-255
Position
Channel 4
Tilt fine adjustment
0-100%
0-255
Position
Channel 5
Color Wheel
Full
98
96
94
93
91
90
88
87
85
83
82
80
79
77
76
255
250
245
240
237
232
230
224
222
217
211
209
204
201
196
194
Color 1 (open)
Half color 1 and 2
Color 2
Half color 2 and 3
Color 3
Half color 3 and 4
Color 4
Half color 4 and 5
Color 5
Half color 5 and 6
Color 6
Half color 6 and 7
Color 7
Half color 7 and 8
Color 8
Half color 8 and 1
74
73
71
70
68
66
65
63
62
61
59
57
56
54
52
51
189
186
181
179
173
168
166
161
158
156
150
145
143
138
133
130
Color 1 (open)
Half color 1 and 2
Color 2
Half color 2 and 3
Color 3
Half color 3 and 4
Color 4
Half color 4 and 5
Color 5
Half color 5 and 6
Color 6
Half color 6 and 7
Color 7
Half color 7 and 8
Color 8
Half color 8 and 1
Full Speed
Color Wheel
Mspeed
A-8
Channel
Value (%)
Cyberlight User Manual
Table A-4: Cyberlight DMX Assignments Mode 2
Channel
Assignment
Color Wheel
Channel
Value (%)
Channel
Value
(numerical)
50
127
26
25
66
64
0
0
2
0
Spin Speed
Construct Parameter
Forward spin speed – fastest
•
•
•
Forward spin speed – slowest
Reverse spin speed – slowest
•
•
•
Reverse spin speed – fastest
Color 1 (open)
Channel 6
Cyan (Red)
0-100%
0-255
Color Mix
Channel 7
Magenta (Green)
0-100%
0-255
Color Mix
Channel 8
Yellow (Blue)
0-100%
0-255
Color Mix
Channel 9
Static litho
Full
98
96
94
93
91
90
88
87
85
83
82
80
79
77
76
255
250
245
240
237
232
230
224
222
217
211
209
204
201
196
194
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
1 (open)
1 shake wide
2
2 shake wide
3
3 shake wide
4
4 shake wide
5
5 shake wide
6
6 shake wide
7
7 shake wide
8
8 shake wide
74
73
71
70
68
66
65
63
62
61
59
57
56
54
52
51
189
186
181
179
173
168
166
161
158
156
150
145
143
138
133
130
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
Litho
1 (open)
1 shake narrow
2
2 shake narrow
3
3 shake narrow
4
4 shake narrow
5
5 shake narrow
6
6 shake narrow
7
7 shake narrow
8
8 shake narrow
Full Speed
Static litho
Mspeed
Appendix A DMX Control of Cyberlight
A
A-9
Table A-4: Cyberlight DMX Assignments Mode 2
Channel
Assignment
Static litho
Channel
Value (%)
Channel
Value
(numerical)
50
127
26
25
66
64
0
0
2
0
Full
98
95
91
87
83
80
76
72
68
64
61
58
54
255
250
242
232
222
212
204
194
184
173
163
156
150
138
Position 3 (open)
Reverse rotate 5
Reverse rotate 4
Reverse rotate 2
Reverse rotate 1
Forward rotate 5
Forward rotate 4
Forward rotate 2
Forward rotate 1
Position 5
Position 4
Position 3 (open)
Position 2
Position 1
50
46
42
39
36
32
28
24
20
17
13
10
5
0
127
117
107
99
92
82
71
61
51
43
33
26
13
0
Reverse rotate 5
Reverse rotate 4
Reverse rotate 2
Reverse rotate 1
Forward rotate 5
Forward rotate 4
Forward rotate 2
Forward rotate 1
Position 5
Position 4
Position 3 (open)
Position 2
Position 1
Position 3 (open)
Spin Speed
Channel 10
Rotating Litho
Full Speed
Select the litho to rotate
(forward/reverse) with this
channel. Then use Channel
11 to set the rotation speed.
For rotating litho position
parameters select the litho
position to index with this
channel. Then use Channel
11 to set the rotational
position (index value) from 0
to 360 degrees.
Mspeed
Construct Parameter
Forward spin speed – fastest
•
•
•
Forward spin speed – slowest
Reverse spin speed – slowest
•
•
•
Reverse spin speed – fastest
Litho 1 (open)
Channel 11
Rotate
(use with Channel 10)
0-100%
0-255
For Rotating Litho rotate mode use
Ch 11 to set rotate speed
For Rotating Litho position mode
use Ch 11 to set the index from 0
to 360 degrees
Channel 12
Zoom
0-100%
0-255
Zoom in/out
Channel 13
Focus
0-100%
0-255
Focus in/out
Channel 14
Iris
0-100%
0-255
Iris open/close
A-10 Cyberlight User Manual
Table A-4: Cyberlight DMX Assignments Mode 2
Channel
Channel 15
Assignment
Effects Wheel
Full Speed
Channel 15
Effects Wheel
Mspeed
Channel 16
Frost
Channel
Value (%)
Channel
Value
(numerical)
Full
96
91
85
80
73
67
62
56
255
245
232
217
204
186
171
158
143
Effect 4
Effect 8
Effect 7
Effect 6
Effect 5
Effect 4
Effect 3
Effect 2
Effect 1
– (open)
– cyan color corrector
– diffusion
– wide angle
– magenta color corrector
– (open)
– yellow color corrector
– CYM tri-color mosaic
– prism
50
44
37
33
27
21
14
8
0
127
112
94
84
69
54
36
20
0
Effect 8
Effect 7
Effect 6
Effect 5
Effect 4
Effect 3
Effect 2
Effect 1
Effect 4
– cyan color corrector
– diffusion
– wide angle
– magenta color corrector
– (open)
– yellow color corrector
– tri color mosaic (C-Y-M)
– prism
– (open)
Full
255
50
129
Frost – frost free
•
•
•
Frost – frost full
50
126
0
0
2
0
Full
98
97
255
250
247
1
1
0
4
1
0
100
255
0
0
Full
255-200
0
21
0
Frost variable
None to full
Frost
Full Frost Strobing
(Frost in)
Channel 17
Shutter
Strobe
50 % duty cycle
Channel 18
Channel 19
Dim
Motor Speed
Construct Parameter
Frost strobing – fastest
•
•
•
Frost strobing – slowest
Frost – frost free
Open
Closed
Strobe speed – fastest
•
•
•
Strobe speed – slowest
Open
Closed
No dim
Full dim (blackout)
Speed 99
•
•
•
Speed 1
Speed 95
Appendix A DMX Control of Cyberlight A-11
A
Table A-4: Cyberlight DMX Assignments Mode 2
Channel
Channel 20*
Assignment
Control
Channel
Value (%)
Channel
Value
(numerical)
50%
25%
128
64
Construct Parameter
shutdown
home
* - Make sure you first follow the instructions in the section titled “Accessing Control Information” on page A-2.
A-12 Cyberlight User Manual
DMX 512 Mode 3 – Cyberlight® 15-Channel DMX
Control
Each Cyberlight fixture in DMX mode 3 uses 15 channels of the DMX 512 protocol thus providing control for up
to 34 fixtures (512 / 15 = 34.1 fixtures). Use the procedure below to control your Cyberlight with DMX mode 3:
1.
Set the Cyberlight fixture to DMX mode 3 by setting address switches 7 and 8 to ON.
2.
Set address switches 1 through 6 as shown in Table A-5.
3.
Refer to Table A-6 for the Cyberlight 15-channel assignments.
Table A-5: Addressing Fixtures in 15 Channel DMX 512 Mode 3
Cyberlight
Fixture
Fixture
Address
Switches ON
DMX Channel
Number
Cyberlight
Fixture
Fixture
Address
Switches ON
DMX Channel
Number
Fixture 1
none
001
Fixture 18
1 and 5
256
Fixture 2
1
016
Fixture 19
2 and 5
271
Fixture 3
2
031
Fixture 20
1,2, and 5
286
Fixture 4
1 and 2
046
Fixture 21
3 and 5
301
Fixture 5
3
61
Fixture 22
1, 3, and 5
316
Fixture 6
1 and 3
076
Fixture 23
2, 3, and 5
331
Fixture 7
2 and 3
091
Fixture 24
1, 2, 3, and 5
346
Fixture 8
1, 2, and 3
106
Fixture 25
4 and 5
361
Fixture 9
4
121
Fixture 26
1, 4, and 5
376
Fixture 10
1 and 4
136
Fixture 27
2, 4, and 5
391
Fixture 11
2 and 4
151
Fixture 28
1, 2, 4, and 5
406
Fixture 12
1, 2, and 4
166
Fixture 29
3, 4, and 5
421
Fixture 13
3 and 4
181
Fixture 30
1, 3, 4, and 5
436
Fixture 14
1, 3, and 4
196
Fixture 31
2, 3, 4, and 5
451
Fixture 15
2, 3, and 4
211
Fixture 32
1, 2, 3, 4,and 5
466
Fixture 16
1, 2, 3, and 4
226
Fixture 33
6
481
Fixture 17
5
241
Fixture 34
1 and 6
496
Appendix A DMX Control of Cyberlight A-13
A
Table A-6: Cyberlight DMX Assignments Mode 3
Channel
Assignment
Range %
Construct Parameter
Channel 1
Pan coarse adjustment
Position
Channel 2
Pan fine adjustment
Position
Channel 3
Tilt coarse adjustment
Position
Channel 4
Tilt fine adjustment
Position
Channel 5
Color Wheel
Full Speed
Color Wheel
Mspeed
Color Wheel
Full
98
96
94
93
91
90
88
87
85
83
82
80
79
77
76
Color 1 (open)
Half color 1 and 2
Color 2
Half color 2 and 3
Color 3
Half color 3 and 4
Color 4
Half color 4 and 5
Color 5
Half color 5 and 6
Color 6
Half color 6 and 7
Color 7
Half color 7 and 8
Color 8
Half color 8 and 1
74
73
71
70
68
66
65
63
62
61
59
57
56
54
52
51
Color 1 (open)
Half color 1 and 2
Color 2
Half color 2 and 3
Color 3
Half color 3 and 4
Color 4
Half color 4 and 5
Color 5
Half color 5 and 6
Color 6
Half color 6 and 7
Color 7
Half color 7 and 8
Color 8
Half color 8 and 1
50
Forward spin speed – fastest
•
•
•
Forward spin speed – slowest
Reverse spin speed – slowest
•
•
•
Reverse spin speed – fastest
Color 1 (open)
Spin Speed
26
25
0
0
A-14 Cyberlight User Manual
Table A-6: Cyberlight DMX Assignments Mode 3
Channel
Channel 6
Assignment
Static litho
Full Speed
Static litho
Mspeed
Static litho
Range %
Construct Parameter
Full
98
96
94
93
91
90
88
87
85
83
82
80
79
77
76
Litho 1
Litho 1
Litho 2
Litho 2
Litho 3
Litho 3
Litho 4
Litho 4
Litho 5
Litho 5
Litho 6
Litho 6
Litho 7
Litho 7
Litho 8
Litho 8
(open)
shake wide
74
73
71
70
68
66
65
63
62
61
59
57
56
54
52
51
Litho 1
Litho 1
Litho 2
Litho 2
Litho 3
Litho 3
Litho 4
Litho 4
Litho 5
Litho 5
Litho 6
Litho 6
Litho 7
Litho 7
Litho 8
Litho 8
(open)
shake narrow
50
Forward spin speed – fastest
•
•
•
Forward spin speed – slowest
Reverse spin speed – slowest
•
•
•
Reverse spin speed – fastest
Litho 1 (open)
Spin Speed
26
25
0
0
shake wide
shake wide
shake wide
shake wide
shake wide
shake wide
shake wide
shake narrow
shake narrow
shake narrow
shake narrow
shake narrow
shake narrow
shake narrow
Appendix A DMX Control of Cyberlight A-15
A
Table A-6: Cyberlight DMX Assignments Mode 3
Channel
Channel 7
Assignment
Rotating Litho
Full Speed
Select the litho to rotate
(forward/reverse) with this
channel. Then use Channel
11 to set the rotation speed.
For rotating litho position
parameters select the litho
position to index with this
channel. Then use Channel
11 to set the rotational
position (index value) from 0
to 360 degrees.
Mspeed
Range %
Construct Parameter
Full
98
95
91
87
83
80
76
72
68
64
61
58
54
Position 3 (open)
Reverse rotate 5
Reverse rotate 4
Reverse rotate 2
Reverse rotate 1
Forward rotate 5
Forward rotate 4
Forward rotate 2
Forward rotate 1
Position 5
Position 4
Position 3 (open)
Position 2
Position 1
50
46
42
39
36
32
28
24
20
17
13
10
5
0
Reverse rotate 5
Reverse rotate 4
Reverse rotate 2
Reverse rotate 1
Forward rotate 5
Forward rotate 4
Forward rotate 2
Forward rotate 1
Position 5
Position 4
Position 3 (open)
Position 2
Position 1
Position 3 (open)
Channel 8
Rotate
(use with Channel 7)
For Rotating Litho rotate mode use Ch 8 to set
rotate speed
For Rotating Litho position mode use Ch 8 to set the
index from 0 to 360 degrees
Channel 9
Focus
Focus in/out
Channel 10
Iris
Iris open/close
Channel 11
Effects Wheel
Full Speed
Channel 11
Effects Wheel
Mspeed
A-16 Cyberlight User Manual
Full
96
91
85
80
73
67
62
56
Effect 4 – (open)
Effect 8 – cyan color corrector
Effect 7 – diffusion
Effect 6 – wide angle
Effect 5 – magenta color corrector
Effect 4 – (open)
Effect 3 – yellow color corrector
Effect 2 – cym tri color mosaic
Effect 1 – prism
50
44
37
33
27
21
14
8
0
Effect 8 – cyan color corrector
Effect 7 – diffusion
Effect 6 – wide angle
Effect 5 – magenta color corrector
Effect 4 – (open)
Effect 3 – yellow color corrector
Effect 2 – tri color mosaic (C-Y-M)
Effect 1 – prism
Effect 4 – (open)
Table A-6: Cyberlight DMX Assignments Mode 3
Channel
Channel 12
Assignment
Shutter
Strobe
50 % duty cycle
Range %
Full
98
97
1
1
0
Channel 13
Dim
Channel 14
Motor Speed
Control
Open
Closed
Strobe speed – fastest
•
•
•
Strobe speed – slowest
Open
Closed
Dim open/close
Full
0
Channel 15*
Construct Parameter
Speed 97
•
•
•
Speed 1
Speed 94
50% fader – shutdown
25% fader – home
* - Make sure you first follow the instructions in the section titled “Accessing Control Information” on page A-2.
Appendix A DMX Control of Cyberlight A-17
A
Channel Boundaries
This section describes the relationship between DMX address and fixture number, and explains how to mix
fixtures using DMX modes 1 or 2 with DMX mode 3 on the same link.
Overview
DMX 512 protocol provides 512 channels that are divided among all the fixtures connected to the controller
in a particular link. The number of channels that a fixture uses depends on the requirements and design of
the fixture. In theory, you could have one fixture that uses 512 channels, two fixtures that use 256 channels,
four fixtures that use 128 channels, up to 512 fixtures that use one channel each.
Each Cyberlight fixture uses a contiguous block of channels with each block having a unique starting
address. The block of channels assigned to each address defines its channel boundary. Channel boundaries
can start at any address, even or odd. The exact address depends on the fixture’s addressing scheme.
Cyberlight DMX modes 1 and 2 are each on 20-channel boundaries while mode 3 is on a 15-channel
boundary.
Correlation of Fixture Number and DMX Address
Table A-7 and Table A-8 correlate DMX mode fixture numbering to actual DMX 512 addresses.
Table A-7: 20-Channel Addresses (Modes 1 and 2)
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
1: 1-20
6: 101-120
11: 201-220
16: 301-320
21: 401-420
2: 21-40
7: 121-140
12: 221-240
17: 321-340
22: 421-440
3: 41-60
8: 141-160
13: 241-260
18: 341-360
23: 441-460
4: 61-80
9: 161-180
14: 261-280
19: 361-380
24: 461-480
5: 81-100
10: 181-200
15: 281-300
20: 381-400
25: 481-500
Appendix A DMX Control of Cyberlight A-18
A
Table A-8: 15-Channel Addresses (Mode 3)
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
Fixture
Number:DMX
Address
Range
1: 1-15
7: 91-105
13: 181-195
19: 271-285
25: 361-375
31: 451-465
2: 16-30
8: 106-120
14: 196-210
20: 286-300
26: 376-390
32: 466-480
3: 31-45
9: 121-135
15: 211-225
21: 301-315
27: 391-405
33: 481-495
4: 46-60
10: 136-150
16: 226-240
22: 316-330
28: 406-420
34: 496-511
5: 61-75
11: 151-165
17: 241-255
23: 331-345
29: 421-435
6: 76-90
12: 166-180
18: 256-270
24: 346-360
30: 436-450
A
Appendix A DMX Control of Cyberlight A-19
Mixing Modes on the Same Link
High End Systems recommends that you assign all Cyberlight fixtures on a particular link to the same DMX
mode. This saves you from having to remember which commands are supported by which mode for which
fixture. All Cyberlight models (CLs, CXs and SVs) are compatible with all three DMX modes. The only
differences in functionality are between CXs and CLs/SVs; namely, CXs do not support zoom or color
mixing. A CX will simply not respond to color mixing or zoom commands.
If you do wish to mix DMX modes on a particular link, however, you need to be aware that addressing 20channel and 15-channel fixtures in an unplanned fashion can cause wasted channels because of boundary
overlapping. For example, notice in Figure A-2 that to address two 20-channel fixtures and two 15-channels
fixtures in the order, 20 - 15 - 20 - 15 would waste 35 channels. (Fixture numbers 2, 5 and 6 cannot be used
because address ranges used by the fixtures would overlap.)
Addressing the same fixtures in a planned order, 20 - 20 - 15 - 15, would waste only 5 channels as Figure
A-3 shows.
1
2
3
4
5
6
7
20 Channel:
1–20
21–40
41–60
61–80
81–100
101–120
121–140
15 Channel:
(CX)
1–15
16–30
31–45
46–60
61–75
76–90
91–105
Fixture:
Figure A-2. Unplanned channel addressing wastes DMX addresses because of fixture
boundary overlap.
1
2
3
4
5
6
7
20 Channel:
1–20
21–40
41–60
61–80
81–100
101–120
121–140
15 Channel:
(CX)
1–15
16–30
31–45
46–60
61–75
76–90
91–105
Fixture:
Figure A-3. Planned channel addressing wastes a minimum of DMX address space.
Appendix A DMX Control of Cyberlight A-20
A
Appendix B
Cyberlight® Mirror Movement Times
Use this appendix to determine the mirror movement times in seconds for the speed range of 0 to 99. Note
that these values also apply to the Intellabeam and Trackspot fixtures.
Speed #
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
Time (sec.)
0.15
0.17
0.22
0.34
0.41
0.55
0.73
0.94
1.18
1.45
1.76
2.09
2.46
2.86
3.30
3.76
4.26
4.79
5.35
5.94
6.57
7.22
7.91
8.64
9.39
10.17
10.99
11.84
12.72
13.64
14.58
15.56
16.57
17.61
18.69
19.79
20.93
22.10
23.30
24.54
25.80
27.10
28.44
29.80
31.19
Speed #
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
Time (sec.)
32.62
34.08
35.57
37.09
38.65
40.23
41.85
43.50
45.19
46.90
48.65
50.43
52.2
54.09
55.96
57.87
59.81
61.78
63.78
65.82
67.89
69.99
72.12
74.28
76.48
78.71
80.97
83.26
85.59
87.95
90.33
92.76
95.21
97.69
100.21
102.76
105.34
107.95
110.60
113.28
115.98
118.73
121.50
124.31
127.14
Appendix B Cyberlight Mirror Movement Times
B
B-1
Speed #
9
8
7
6
5
B-2
Cyberlight User Manual
Time (sec.)
130.01
132.91
135.85
138.82
141.81
Speed #
4
3
2
1
0
Time (sec.)
144.84
147.90
151.00
154.13
157.28
Appendix C
Factory-Installed Wheels
This appendix shows how the static litho, rotating litho, color and effects wheels are configured by the factory
when Cyberlight is shipped. The numbers shown around the outside of the wheels are the position numbers used
by a controller to select that effect. For example, choosing position 5 on the CX static litho wheel (shown in
Figure C-1 below) with a controller selects the “tunnel” litho.
CX static litho wheel:
C
Figure C-1. Factory configuration of the CX static litho wheel.
Litho names:
1
open
5
tunnel
2
beveled star
6
indigo dots
3
indigo spin
7
netwerk
4
groovy
8
sharp burst
Appendix C Factory-Installed Wheels
C-1
CL/SV static litho wheel:
5
6
4
3
7
open
2
8
1
Figure C-2. Factory configuration of the CL/SV static litho wheel.
Litho names:
C-2
Cyberlight User Manual
1
open
5
tunnel
2
alien star
6
egyptian
space
3
shimmering
star
7
conoid
4
indigo dye
8
disconnect
CX rotating litho wheel:
2
1
open
3
5
C
4
Figure C-3. Factory configuration of the CX rotating litho wheel.
Litho names:
1
droplets
2
paperstack
3
open
4
red wedge
5
indigo
square
Appendix C Factory-Installed Wheels
C-3
CL/SV rotating litho wheel:
2
1
open
5
4
Figure C-4. Factory configuration of the CL/SV rotating litho wheel.
Litho names:
C-4
Cyberlight User Manual
1
ribbed glass
2
psy-spin
3
open
4
indigo
chiclet
5
wavy black
3
CX color wheel:
5
6
4
Green
Magenta
7
Aqua
Medium
Blue
Yellow
Red
3
Indigo
Open
2
8
1
C
Figure C-5. Factory configuration of the CX color wheel.
Appendix C Factory-Installed Wheels
C-5
CL/SV color wheel:
5
6
4
Aqua
CL Color
Corrector
Dark Blue
7
Dark
Orange
Purple
Indigo
Red
Open
8
2
1
Figure C-6. Factory configuration of the CL/SV color wheel.
C-6
Cyberlight User Manual
3
Effects wheel for all Cyberlight models (CX, SV and CL):
5
6
Wide
angle
Magenta
color
corrector
4
open
7
Diffusion
Yellow
color
corrector
Cyan color
corrector
8
Prism
3
Tri-color
mosaic
2
1
C
Figure C-7. Effects wheel for the CL, CX and SV models.
Appendix C Factory-Installed Wheels
C-7
C-8
Cyberlight User Manual
Appendix D
Typical Voltages Worldwide
This Appendix lists typical worldwide voltage ratings based on High End Systems Inc.’s experience.
Although High End Systems believes this information to be reasonably correct to the extent of our
knowledge, you should heed the Warning below before proceeding.
Warning
Information in this table is subject to change. Before selecting a voltage/
frequency for your Cyberlight, you should verify the correct voltage/frequency
setting with a local authority. Selecting an incorrect voltage/frequency will
result in an electric shock hazard and can cause injury to persons as well as
damage the fixture. High End Systems can accept no responsibility for damage
to your Cyberlight or other equipment caused by an incorrect voltage/frequency
setting.
Continent
Country
Africa
Algeria
Angola
Benin
Bophuthatswana
Botswana
Burkina Faso (Upper
Burundi
Cameroon
Canary Islands
Central African
Chad
Congo
Dahomey
Djibouti
Egypt
Ethiopia
Gabon
Gambia
Ghana
Guinea
Ivory Coast
Kenya
Lesotho
Liberia
Libya
Malagasy Republic
Malawi
Mali
Mauritania
Mauritius
Morocco
Mozambique
Namibia/ SW Africa
Niger
Nigeria
Rwanda
Senegal
Seychelles
Senegambia
Sierra Leone
Somalia
South Africa
Sudan
Swaziland
Hz
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
Supply
127–220V
220V
220V
220V
220V
220V
220V
127–220V
127–220V
220V
220V
220V
220V
220V
110–220V
220V
220V
230V
240V
220V
220V
240V
230V
120V
110–115V
127–220V
230V
220V
220V
230V
110–127V
220V
220V
220V
230V
220V
110V
240V
127V
230V
220V
220V
240V
220V
Cyberlight Voltage Tab Setting
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S8 205V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 205V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 205V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
Appendix D Typical Voltages Worldwide
D
D-1
Continent
Africa
Country
Tanzania
Togo
Tunisia
Uganda
Upper Volta (Burkina
Zaire
Zambia
Zimbabwe
Australia Australia
Fiji Islands
Guam
New Caledonia
New Zealand
Papua New Guinea
Soloman Islands
Tahiti
Tonga
Western Samoa
Asia
Afghanistan
Bangladesh
Brunei
Burma
Cambodia
China
Hong Kong
India
Indonesia
Japan
Kazakhstan
Kirgizstan
Korea (North)
Korea (South)
Laos
Macao
Malaysia
Myanmar
Nepal
Phillipines
Russia
Saah (N. Borneo)
Singapore
Sri Lanka (Ceylon)
Taiwan
Tajikistan
Thailand
Turkmenistan
Vietnam
Central
America
D-2
Cyberlight User Manual
Anguilla
Antigua (Leeward Is.)
Bahamas
Barbados
Belize
Bermuda
Cayman Islands
Costa Rica
Cuba
Dominica
Dominican Republic
El Salvador
Grenada
Guadeloupe
Guatemala
Haiti
Honduras
Jamaica
Martinique
Mexico
Hz
50
50
50
50
50
50
50
50
Supply
230V
127–220V
127–220V
240V
220V
220V
220V
220V
Cyberlight Voltage Tab Setting
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
50
50
60
50
50
50
50
60
50
50
50/60
50
50
50
50
50
50
50
50
50/60
50
50
60
60
50
50
50
50
50
60
50
50
50
50
60
50
50
50
50
240–265V
240V
120
220V
230–245V
240V
240V
127V
230V
230V
220V
230V
240V
230V
120–220V
220V
220V
230V
127–220V
100–200V
220V
220V
220V
110–220V
220V
115–220V
240V
230V
220V
110–220V
127–220
240V
230–245V
230V
110V
220V
220V
220V
120V
S6 240V / 50 Hz
S6 240V / 50 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S6 240V / 50 Hz
S6 240V / 50 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 205V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 230V / 60 Hz
S8 230V / 60 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 230V / 60 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
50
50
60
50
60
60
60
60
60
60
60
60
50
50
60
60
60
50
50
60
230V
230V
115V
115V
110–220V
115V
120V
120V
115–120V
110–220V
110V
115V
230V
220V
115V
110V
110V
110–220V
220V
120V
S7 230V / 50 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
Continent
Central
America
Europe
Middle
East
Country
Monteserrat
Netherland Antilles
Nicaragua
Panama
Puerto Rico
St. Kitts & Nevis
St. Lucia
St. Vincent
Trinidad & Tobago
Virgin Islands
Hz
60
50
60
60
60
60
50
50
60
60
Supply
230V
110–127V
120V
110–120
120V
230V
240V
230V
115–230V
120V
Cyberlight Voltage Tab Setting
S8 230V / 60 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S8 230V / 60 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S8 230V / 60 Hz
S9 208V / 60 Hz
Albania
Austria
Azores
Belarus
Belgium
Bosnia Herzegovina
Bulgaria
Channel Islands
Croatia
Czech Republic
Denmark
Estonia
Faeroe Islands
France
Finland
Germany
Gibralter
Greece
Greenland
Hungary
Iceland
Ireland
Isle of Man
Italy
Latvia
Lithuania
Luxembourg
Macedonia
Madiera
Majorca Island
Malta
Moldova
Monaco
Montenegro
Netherlands
Northern Ireland
Norway
Poland
Portugal
Romania
Russia
Serbia
Slovakia
Slovenia
Spain
Sweden
Switzerland
Ukraine
United Kingdom
Yugoslavia
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
220–380V
220V
220V
220V
220V
220V
220V
210–240V
220V
220V
220V
220V
220V
220V
220V
220V
240V
220V
220V
220V
220V
220V
240V
220V
220V
220V
220V
220V
220V
220V
240V
220V
220V
220V
220V
230V
220–230V
220V
220V
220V
220V
220V
220V
220V
210–220V
220V
220V
220V
220–250V
220V
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
Armenia
Azerbiajan
Abu Dhabi
Afghanistan
Bahrain
Cyprus
Georgia
50
50
50
50
50
50
50
220V
220V
240V
220V
230V
240V
220V
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
Appendix D Typical Voltages Worldwide
D
D-3
Continent
Country
Iran
Iraq
Israel
Jordan
Kuwait
Lebanon
Muscat
Oman
Pakistan
Qatar
Saudi Arabia
Sudan
Syria
Turkey
United Arab Emirates
Yemen
Hz
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
Supply
220V
220V
230V
220V
240V
110–220V
240V
240V
230V
240V
127–220V
240V
220V
220V
220V
220V
Cyberlight Voltage Tab Setting
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S6 240V / 50 Hz
S8 230V / 60 Hz
S6 240V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
S7 230V / 50 Hz
North
America
Canada
United States
60
60
115V
120V
S9 208V / 60 Hz
S9 208V / 60 Hz
South
America
Argentina
Bolivia
Brazil
Chile
Columbia
Ecuador
French Guiana
Guyana
Paraguay
Peru
Suriname
Uruguay
Venezuela
50
50
60
50
60
60
50
60/50
50
60
60
50
60
220V
110V
110–127–
220V
110–120V
110–120V
220V
110V/60 &
220V
220V
110–127V
220V
120V
S7 230V / 50 Hz
S7 230V / 50 Hz
S8 230V / 60 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S9 208/60 Hz & S6 240V/50 Hz
S7 230V / 50 Hz
S8 230V / 60 Hz
S9 208V / 60 Hz
S7 230V / 50 Hz
S9 208V / 60 Hz
Middle
East
D-4
Cyberlight User Manual
Appendix E
Important Safety Information
WARNING: For Continued Protection Against Fire
1. This equipment is designed for use with Philips type MSR1200 or MSD1200, 1200
watt lamp only. Use of any other type lamp may be hazardous and will void the
warranty.
2. Do not mount on a flammable surface.
3. Maintain minimum distance of 1.0 meter (3.28 feet) from combustible materials.
4. Replace fuses only with the specified type and rating.
5. Observe minimum distance to lighted objects of 1.0 meter (3.28 feet).
6. This equipment for connection to branch circuit having a maximum overload
protection of 20 A.
WARNING: For Continued Protection Against Electric Shock
1. If this equipment was received without a line cord plug, attach the appropriate line
cord plug according to the following code:
•
•
•
Brown–live
Blue–neutral
Green/yellow–earth
E
2. As the colours of the cores in the mains lead of this equipment may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:
- the core which is coloured green and yellow must be connected to the terminal in the
plug which is marked with the letter “E” or by the earth symbol , or coloured green or
green and yellow.
- the core which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
- the core which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
3. This equipment must be earthed.
4. Disconnect power before re-lamping or servicing.
Appendix E Important Safety Information
E-1
5. Equipment suitable for dry locations only. Do not expose this equipment to rain or
moisture.
6. Refer servicing to qualified personnel; no user serviceable parts inside.
7. Class I equipment - this fixture employs a grounded type receptacle and is not
intended for connection to a two wire, ungrounded source of supply.
WARNING: For Continued Protection Against Exposure To Excessive Ultraviolet (UV)
Radiation
1. Do not operate this equipment without complete lamp enclosure in place or if shields,
lenses, or ultraviolet screens are damaged.
2. Change shields, lenses, or ultraviolet screens if they have become visibly damaged to
such an extent that their effectiveness is impaired, for example by cracks or deep
scratches.
3. Never look directly at the lamp while lamp is on.
WARNING: For Continued Protection Against Injury To Persons
1. Use secondary safety cable when mounting this fixture.
2. CAUTION: Hot lamp may be an explosion hazard. Do not open for 5 minutes after
switching off. wear eye and hand protection when re-lamping.
3. Equipment surfaces may reach temperatures up to 62° C (144° F). Allow 10 minutes
for cooling before handling.
4. Change the lamp if it becomes damaged or thermally deformed.
E-2
Cyberlight User Manual
APPENDICE E
IMPORTANTES INFORMATIONS SUR LA SÉCURITÉ
MISE EN GARDE: Pour Une Protection Permanente Contre Les Incendies
1. Cet appareil est conçu pour être exclusivement utilisé avec des lampes de 1200 watts
MSR 1200 ou MSD 1200. L'usage d'autres lampes peut être risqué et annulera la
garantie.
2. Ne pas monter les lampes sur une surface inflammable.
3. Maintenir à une distance minimum de 1.0 mètre de matières inflammables.
4. Ne remplacer les fusibles qu'avec des modèles et valeurs assignées recommandés.
5. Respecter une distance minimum de 1.0 mètre par rapport aux objets éclairés.
6. Cet appareil de connexion au circuit de dérivation comporte une protection contre les
surcharges de 20A.
MISE EN GARDE: Pour Une Protection Permanente Contre Les Chocs Électriques
1. Assembler le câble électrique conformément aux instructions du manuel.
2. Déconnecter le courant avant de changer les lampes ou d'effectuer des réparations.
3. Cet équipement doit être uniquement utilisé dans des endroits secs. Ne pas l'exposer à
la pluie ou l'humidité.
4. À l'intérieur de l'équipement il n'y a pas de pièces remplaçables par l' utilisateur.
Confiez l'entretien à un personnel qualifié.
E
5. Equipement de Classe I - Cette piece fixe utilise une prise de courant branché à la
terre et elle ne doit pas être branché à une source électrique, non reliée à la terre, à
double fil.
Appendix E Important Safety Information
E-3
MISE EN GARDE: Pour Une Protection Permanente Contre Des Expositions
Excessives Aux Rayons Ultra Violets (UV)
1. Ne pas utiliser cet appareil si le boîtier de la lampe n'est pas complètement fixé ou si
les blindages, lentilles, ou écrans ultraviolets sont endommagés.
2. Changer les blindages ou les écrans ultraviolets s'ils sont visiblement endommagés au
point que leur efficacité aient été altérée, par exemple par des fissures ou de
profondes égratignures.
3. Ne jamais regarder directement la lampe quand celle ci est allumée.
MISE EN GARDE: Pour Une Protection Permanente Contre Les Blessures Corporelles
1. Lors de l'assemblage ou du montage, utiliser un câble de sécurité secondaire.
2. AVERTISSEMENT: les lampes chaudes comportent un risque d'explosion. Après
l'avoir éteinte, attendre 5 minutes avant de la dégager. Lors du remplacement de la
lampe, porter des lunettes, et des gants de protection.
3. Les surfaces de l'appareil peuvent atteindre des températures de 62° C. Laisser
refroidir pendant 10 minutes avant la manipulation.
4. Changer la lampe si elle est endommagée ou thermiquement déformé.
E-4
Cyberlight User Manual
ANHANG E
WICHTIGE HINWEISE FÜR IHRE SICHERHEIT
WARNUNG: Zum Schutz vor Brandgefahr
1. Dieses Gerät darf nur mit 1200 Watt Lampen vom Typ MSR 1200 oder MSD 1200 von
Philips verwendet werden. Die Verwendung von Lampen eines anderen Typs kann
gefährlich sein und ein Erlöschen der Garantieansprüche zur Folge haben.
2. Das Gerät nie auf einer feuergefährlichen Fläche montieren.
3. Stets einen Mindestabstand von 1 Meter zu brennbaren Materialien einhalten.
4. Zum Ersatz nur Sicherungen verwenden, die dem vorgeschriebenen Typ und
Nennwert entsprechen.
5. Einen Mindestabstand von 1 Meter zu den angestrahlten Objekten einhalten.
6. Dieses Gerät darf nur an eine Zweigleitung mit einem Überlastungsschutz von
höchstens 20 A angeschlossen werden.
WARNUNG: Zum Schutz Gegen Gefährliche Körperströme
1. Bei der Installation des Netzkabels am Lampensockel folgen Sie bitte Anweisungen in
diesem Handbuch.
2. Vor dem Austauschen von Lampen oder vor Wartungsarbeiten stets den Netzstecker
ziehen.
3. Diese Geräte sind nur zum Einbau in trockenen Lagen bestimmt und müssen vor
Regen und Feuchtigkeit geschützt werden.
E
4. Servicearbeiten sollten nur von Fachpersonal ausgeführt werden. Das Gerät enthält
keine wartungsbedürftigen Teile.
5. Dieses Gerät gehört zur Klasse 1 - Dieser Beleuchtungskörper verwendet eine
geerdete Fassung und sollte nicht an eine zweipolige, ungeerdete Stromversorgung
angeschlossen werden.
Appendix E Important Safety Information
E-5
WARNUNG: Zum Schutz Gegen Übermässige Ultraviolett (UV)-bestrahlung
1. Benutzen Sie dieses Gerät nur, wenn das komplette Lampengehäuse fest eingebaut ist;
ebenfalls dürfen keine der Schutzabdeckungen, Linsen oder der UV-Schutz
Beschädigungen aufweisen.
2. Die Schutzabdeckungen, Linsen und der UV-Schutz müssen ausgewechselt werden,
wenn sie sichtlich dermaßen beschädigt sind, daß sie ihre Wirksamkeit einbüßen, z.B.
infolge von Rissen oder tiefen Kratzern.
3. Nie direkt in die eingeschaltete Lampe schauen.
WARNUNG: Zum Schutz Vor Verletzungen
1. Verwenden Sie bei der Installation des Beleuchtungskörpers ein zusätzliches
Sicherheitskabel.
2. VORSICHT: Bei einer heiße Lampe besteht Explosionsgefahr. Nach dem Abschalten
der Netzspannung sollten Sie etwa 5 Minuten warten, bevor Sie das Lampengehäuse
öffnen. Schützen Sie beim Auswechseln der Lampen Ihre Hände und tragen Sie eine
Schutzbrille.
3. Die Oberflächen des Gerätes können Temperaturen bis zu 62° C erreichen. Vor dem
Anfassen stets 10 Minuten lang abkühlen lassen.
4. Falls die Lampe beschädigt oder durch Wärmeeinwirkung verformt ist, muß sie
ausgewechselt werden.
E-6
Cyberlight User Manual
APÉNDICE E
INFORMACIÓN IMPORTANTE DE SEGURIDAD
ADVERTENCIA: Para Protección Continua Contra Incendios
1. Se ha diseñado este equipo para usarse con lámpara tipo philips MSR1200 ó MSD
1200, 1200 vatios. El uso de otro tipo de lámpara puede resultar peligroso e invalidará
la garantía.
2. No monte el equipo sobre una superficie inflamable.
3. Mantenga una distancia mínima de materiales combustibles de 1,0 metro.
4. Cambie los fusibles únicamente por otros que sean del tipo y la clasificación
especificadas.
5. Observe una distancia mínima a objetos iluminados de 1,0 metro.
6. Este equipo debe conectarse a un circuito derivado que tenga una protección máxima
contra las sobrecargas de 20 A.
ADVERTENCIA: Para La Protección Continua Contra Electrocuciones
1. Ensamble la tapa del cordón de alimentación según las instrucciones del manual.
2. Desconecte el suministro de energía antes de recambiar lámparas o prestar servicio de
reparación.
3. Este equipo se adecua a lugares secos solamente. no lo exponga a la lluvia o humedad.
E
4. Derive el servicio de reparación de este equipo al personal calificado. El interior no
contiene repuestos que puedan ser reparados por el usuario.
5. Equipo de Clase 1. Este aparato emplea un enchufe hembra del tipo unido a tierra, y
no tiene por finalidad conectarse a una fuente de alimentación bifilar y sin puesta a
tierra.
Appendix E Important Safety Information
E-7
ADVERTENCIA: Para Protección Continua Contra La Exposición A Radiación
Ultravioleta (UV) Excesiva
1. No opere este equipo sin tener colocada en su lugar la caja protectora completa de la
lámpara o bien, si el blindaje, los lentes o las pantallas ultravioletas están dañadas.
2. Cambie el blindaje, los lentes o las pantallas ultravioleta si nota una avería visible, a
tal grado que su eficacia se vea comprometida, por ejemplo, en el caso de grietas o
rayaduras profundas.
3. Jamás mire directamente a la lámpara en tanto ésta esté encendida.
ADVERTENCIA: Para Protección Continua Contra Lesiones Corporales
1. Use cable secundario de seguridad al montar este aparato.
2. PRECAUCIÓN: Una lámpara caliente puede constituir un peligro de explosión. No la
abra por 5 minutos luego de haberla apagado. Lleve puestos un protector ocular y
guantes al recambiar lámparas.
3. Las superficies del equipo pueden alcanzar temperaturas máximas de 62 grados
centígrados. Deje que se enfríen por 10 minutos antes de tocarlas.
4. Cambie la lámpara si ésta se avería o deforma por acción térmica.
E-8
Cyberlight User Manual
APPENDICE E
IMPORTANTI INFORMAZIONI PER LA SICUREZZA
AVVERTENZA: Per La Prevenire Di Incendi
1. Questo apparecchio e' stato disegnato per l'impiego esclusivo di lampade tipo MSR 1200 o
MSD 1200 Watt. L'impiego di altri tipi di lampade potrebbe essere pericoloso e rende
nulla la garanzia.
2. Non montare su superfici infiammabili.
3. Mantenere l' apparecchio ad una distanza minima di 1 metro (3.28 piedi) da materiali
combustibili.
4. Rimpiazzare I fusibili utilizzando solo quelli del tipo e della portata (Corrente
nominale/velocita') specificata.
5. Mantenere una distanza minima da oggetti illuminati di 1 metro (3.28 Piedi).
6. Questo apparecchio deve essere collegato alla rete con ínterruttore automatico 20A.
AVVERTENZE: Per La Prevenzione Costante Di Scosse Elettriche
1. Assemblare il terminale del cavo seguendo il manuale delle istruzioni.
2. Scollegare la corrente prima di sostituire la lampada o eseguire la riparazione.
3. Questo apparecchio e' adatto ad ambienti secchi e non deve essere esposto ad agenti
atmosferici o ad umidita`.
E
4. Per qualsiasi riparazione rivolgersi a personale specializzato. L' utente non deve riparare
alcuna parte interna dell'apparecchio.
5. Apparecchio di classe I - questo apparecchio e' fornito di presa bipolare + terra e non deve
essere collegato a rete sprovvista di terra.
Appendix E Important Safety Information
E-9
AVVERTENZE: Per La Protezione Costante Da Eccessiva Esposizione Agli
Ultravioletti
1. Non azionare questo apparecchio in caso la lampada non sia schermata o schermi, lenti o
filtri UV siano danneggiati.
2. Cambiare schermi, lenti o filtri UV in caso siano visibilmente danneggiati al punto di
invalidare la loro efficacia, per esempio da spaccature o da profondi graffi.
3. Non guardare direttamente la lampada se accesa.
AVVERTENZE: Per La Prevenzione Costante Di Danni Fisici Alle Persone
1. Montare l'apparecchio usando un cavo secondario di sicurezza.
2. ATTENZIONE: La lampada calda puo' esplodere. Non aprire prima di 5 minuti dal
suo spegnimento. Usare protezioni per le mani e per gli occhi prima di cambiare la
lampada.
3. Le superfici dell'apparecchio possono raggiungere una temperatura di 62 gradi centigradi
(144 Gradi F). Lasciare raffredare 10 minuti prima di maneggiare.
4. Cambiare la lampada in caso si danneggi o deformi per le alte temperature.
E-10 Cyberlight User Manual
Glossary
Additive color mixing
The creation of colors by superimposing red, green and blue light sources. The intensities of
red, green and blue light determine the resulting color. This method is commonly used in TVs
and projection TV/video devices. Additive color mixing done in this way is also called the
RGB (red-green-blue) color model.
See also “Subtractive color mixing”.
Block addressing
The Cyberlight is a block-addressed fixture; that is, you do not address it at an arbitrary DMX
starting address per se, but rather at a channel boundary. There are two channel boundaries
you can select: 15-channel and 20-channel. If you choose to control your Cyberlight on a 20channel boundary, for example, each fixture takes up a contiguous block of 20 DMX channels.
The more channels per fixture, the more features you can control.
See also “Fixture number”.
Central access door
Typically the most commonly-opened door on Cyberlight, where the color, effects, rotating
and static litho wheels may be accessed. Figure 1-2 on page 1-11 shows all three Cyberlight
access doors.
Channel boundary
The first address of a fixture’s block of addresses. For example, a Cyberlight set for fixture
number 2 in 20-channel DMX mode 1 or 2 would have a channel boundary at DMX channel
21.
See also “Block addressing” and “Fixture number”.
Color temperature
A term used to describe the balance or content of each spectral component of white light.
Color temperature, in turn, relies on the concept of the black body. A black body is a
theoretical object that absorbs all of the energy that contacts it. Heating a black body causes it
to emit radiation. When the spectral composition of a black body matches the spectral
composition of a white light source, the temperature of the black body (in degrees Kelvin) is
the color temperature of the light source.
For example, a light source that is rated at 5600° Kelvin (such as the light source used in
Cyberlight) matches the radiation of a black body heated to 5600° Kelvin.
Because not all light sources exhibit a smooth spectral power distribution, color temperature is
an approximate measure of a lamp’s spectral output.
Glossary
G-1
Constructs
Features of the fixture (such as color mixing, lithos, rotating lithos, color wheel, iris, frost and
shutter). Constructs can be used by a controller to program your overall show.
Dichroic
A dichroic (from Greek, meaning “two-color”) filter achieves a richly-saturated color without
using any pigmented (colored) materials. In simple terms, it achieves this effect by either
reflecting or “cancelling out” through destructive interference all but a narrow range of the
light spectrum.
The “dichroic” name refers to the fact that one color (or set of colors) is reflected or cancelled
out, and one color is allowed to be transmitted through the dichroic filter.
The dichroics used in Cyberlight are all manufactured at the High End Systems Optical
Coating and Assembly Laboratory in Austin, Texas. They are made from a base of Pyrex®like glass material coated with multiple, microscopic layers of specialized materials separated
by junctions that either transmit or reflect certain wavelengths of light, accounting for the
resulting color.
Dichroic filters offer a number of advantages over traditional gel filters: since they are made of
Pyrex-like glass and absorb almost no heat themselves, they theoretically have no failure
mechanism; they transmit more light than gels; and their resultant colors are more richlysaturated than is possible with a gel.
Dichroics are currently used for all Cyberlight colored lithos, color mixing flags,
effects and of course the color wheel dichroic filters. Before installing a dichroic or litho
in Cyberlight, make sure you read the section titled “Removing and Installing Rotating Lithos”
on page 3-19 and the section titled “Replacing Dichroics/Lithos in the Color Wheel or the
Static Litho Wheel” on page 3-22.
See also “Litho”.
DMX 512 control protocol
DMX 512 is a standard method of controlling lighting fixtures and other devices (such as
lasers and hazers). Developed by the United States Institute of Theatre Technology (USITT),
DMX 512 is supported by leading entertainment industry equipment manufacturers, such as
High End Systems.
DMX 512 (D for digital, MX for multiplex and 512 is the number of channels per link) is a
reliable, efficient and well-understood method of controlling lighting devices. Its strength lies
in the ability to control a large number of different types of devices made by various vendors
on the same link using any DMX-compatible controller.
See also “LWR control protocol”.
DMX address
The DMX 512 protocol allows a total of 512 addresses to be used on a particular link. (A link
is a group of devices connected on a daisy-chain of XLR cabling.) You need to assign a unique
fixture number to each Cyberlight you wish to respond independently to control commands.
G-2
Cyberlight User Manual
Multiple fixtures can be assigned the same address if you wish them all to respond to control
commands in the same way.
For example, suppose you have 12 Cyberlight fixtures on one link. You want six of them to
operate independently of each other and the other six to operate in exactly the same way. You
need to assign each of the six independently-operating Cyberlight fixtures a unique fixture
number, but you can assign a single fixture number to the other six, for a total of seven fixture
numbers.
DMX modes
You can use DMX 512 protocol to control the Cyberlight in three different modes. The three
DMX modes available for your Cyberlight provide three different levels of control and
flexibility, and can be used with CLs, SVs, and CXs. Mode 1 is 20-channel standard control;
mode 2 is enhanced 20-channel control, and mode 3 is 15-channel control. For more
information on all three modes, see Appendix A.
Fixture number
Because the Cyberlight is a block-addressed fixture, you do not access it using an arbitrary
DMX starting address. Instead, you can choose between 20-channel and 15-channel access
(see Appendix A). Thus, the concept of fixture number can be substituted for the actual DMX
channel.
For example, suppose you have chosen to control the Cyberlight using DMX mode 2, which is
a 20-channel mode. Fixture number 1 occupies DMX addresses 1 through 20; fixture 2
occupies DMX addresses 21 through 40, and so on. A complete listing of how fixture numbers
correlate to DMX addresses can be found in Table A-7 on page A-18.
Lamp box access door
This door provides access to the Cyberlight lamp, infrared filter, reflector and other
components. Figure 1-2 on page 1-11 shows all three Cyberlight access doors.
Lamp strikes
The number of times the lamp has been illuminated. Once the lamp is “switched on”, whether
it is illuminated continuously for one second or one minute, it counts as one strike.
Litho
A litho has a pattern etched on it (some lithos are also textured), as the name “LithoPatterns”
suggests. All LithoPatterns are designed and manufactured at the High End Systems dichroic
lab in Austin, Texas. There are currently a large number of available lithos, including
LithoPatterns, Art Glass, Psy-Dye and Special Effects. See the section titled “Optional
Accessories” on page 1-7 for ordering information.
A dichroic process is used to color all lithos.
See also “Dichroic”.
Glossary
G-3
Luminaire
Synonymous with “fixture”.
LWR control protocol
The native control protocol for Cyberlight, LWR offers all the features of DMX 512 plus it
gives you the ability to perform software uploads using a High End Systems Link Card or the
Cyberlight Upload Module.
MSR/MSD
MSR stands for Medium Source Rare Earth and describes the family of arc lamps used in the
Cyberlight. Rare earth elements (such as Dysprosium and Holmium) are added to metal halide
to give the lamp a more continuous spectrum.
MSD stands for Medium Source Daylight. (“Daylight” is a reference to the fact that the lamp
has roughly the same color temperature as ordinary sunlight.) The MSD lamp has basically the
same composition and the same color temperature as the MSR lamp, but it has a lower light
output and longer life.
See also “Color temperature”.
Strikes
See “Lamp strikes”.
Subtractive color mixing
The creation of colors by filtering out (subtracting) certain wavelengths from a typically white
(multi-wavelength) light source. For example, putting a magenta filter in the path of a white
light source subtracts green light. This is the color mixing model used in Cyberlight.
Typically, the filters used in a subtractive color mixing system are cyan, yellow and magenta;
thus, this is usually referred to as the CYM color mixing model.
See also “Additive color mixing”.
Terminator
A terminator is a resistor inside an XLR connector. It is used to prevent the analog signal from
continuously “echoing” up and down the data link. A terminator must be used on the last
device in every DMX link. Instructions for constructing a terminator can be found in the
section titled “Terminators” on page 2-7.
G-4
Cyberlight User Manual
INDEX
A
Accessories 1-7
Adjustments
mechanical zoom lens 3-23
mirror head 3-24 to 3-25
yoke 3-26
AF1000 2-3
Alignment knobs. See Lamp, installing or
replacing
Anti-reflective glass 3-6
B
Barrel. See Truss
Batten. See Truss
C
Cabling
constructing 2-6 to 2-7
ordering 1-7
pinouts 2-6, 2-7
safety 1-7, 2-10
specifications 1-5
terminators 2-7
C-clamps 2-10
ordering 1-7
Center access door 1-11
Channel boundaries A-18 to A-19
CL 1-6
Clamps 2-10
Cleaning
dichroics 3-7 to 3-10
fans 3-3
flags, reflector and infrared filter 3-10
to 3-14
lithos 3-7 to 3-10
mirror, lenses, motor and iris 3-4 to
3-6
outer surfaces 3-3
rotating lithos 3-14
wheels and sensors 3-7 to 3-10
Color mixing plate 3-12
Color wheel 3-7
factory configuration
CL/SV C-6
CX C-5
ordering custom dichroics 1-7
replacing dichroics 3-22
SV dichroic substitution 1-19 to 1-22
Control. See DMX
CTO color correction filter 1-19
Customer Service intro-4
CX
drawing of 1-6
mechanical zoom lens 3-23
Cyberlight
accessories 1-7
adjustments
mechanical zoom lens 3-23
mirror head 3-24 to 3-25
yoke 3-26
cabling
constructing 2-6 to 2-7
ordering 1-7
pinouts 2-7
terminators 2-7
center access door 1-11
channel boundaries A-18 to A-19
CL 1-6
clamps 2-10
cleaning
fans 3-3
flags, reflector and infrared filter
3-10 to 3-14
internal components 3-4 to 3-14
mirror, lenses, motor and iris 3-4
to 3-6
outer surfaces 3-3
rotating lithos 3-14
wheels and sensors 3-7 to 3-10
color wheel
CL/SV C-6
CX C-5
control. See DMX
CX 1-6
Index
1
DIP switches
address A-2
personality 1-22 to 1-26
DMX or LWR control 2-2
effects wheel C-7
features intro-1 to intro-3
fixture number 2-4 to 2-5, A-18 to
A-19
front fan access door 1-11
fuses 3-18
hanging fixtures. See Cyberlight,
mounting fixtures
homing 1-18
info LED 1-24 to 1-25
examples 1-25
lamp
information counter 1-18
installing or replacing 1-16 to
1-17
ordering 1-7
lamp box access door 1-11
LED descriptions 1-27
maintenance
(see also Maintenance)
adjustments 3-23 to 3-26
cleaning internal components 3-4
to 3-14
general 3-2
replacing parts 3-15 to 3-22
models 1-6
mounting fixtures 2-9 to 2-11
pan invert 1-26
pan/tilt swap 1-26
power
ON and OFF 1-29
power cord cap 1-9 to 1-10
setting voltage 1-10 to 1-14
specifications 1-4
switch 1-29
voltage 1-24
power supply board 1-13
QC plate 1-8
replacing
dichroics/lithos 3-22
lamp 1-16 to 1-18
power supply fuses 3-15 to 3-18
2
Cyberlight User Manual
rotating lithos 3-19 to 3-21
rotating litho wheel
CL/SV C-4
CX C-3
safety cables 2-10
self-test 1-23
setup mode 1-23
specifications
cabling 1-5
electrical 1-4
physical 1-3
safety 1-4
safety standards 1-4
static litho wheel
CL/SV C-2
CX C-1
SV 1-6
drawing of 1-6
substituting dichroics 1-19 to
1-22
tilt invert 1-26
troubleshooting 2-12 to 2-17
version number 1-24
voltage 1-24
yoke
adjusting 3-26
installing 1-14 to 1-15
Cyberlight LCD controller 1-7, 2-2
D
Dichroic intro-2
cleaning 3-7 to 3-10
ordering 1-7
replacing 3-22
substituting in SV 1-19 to 1-22
Dim flags 3-14
DIP switches
address A-2
personality 1-22 to 1-26
DMX
(see also LWR protocol)
channel boundaries A-18 to A-19
description 2-2
fixture number
correlated to DMX address A-18
to A-19
mode 2 A-7
mode 3 A-13
linking devices 2-8
modes
description 2-2
mixing modes 1, 2 and 3 A-20
mode 1 A-3 to A-6
mode 2 A-7 to A-12
mode 3 A-13 to A-17
multiple High End Systems fixtures
2-3
procedure 2-3 to 2-4, A-2 to A-17
selecting DMX or LWR protocol 2-2
software uploads A-1
DMX 512. See DMX
DMX address. See DMX and Fixture
number
Dousing. See Dim flags and Features
E
Effects wheel 3-7
factory configuration C-7
EIA RS-485 2-6
F
G
Gobos. See Lithos
H
Hanging fixtures. See Mounting fixtures
Heat filter. See Infrared filter.
Help intro-4
Help (see also Troubleshooting)
Homing 1-18
Homogenizing frost filter 1-19
I
Info LED 1-24 to 1-25
description 1-27
examples 1-25
Information counter (lamp) 1-18
Infrared filter 3-13
Installing
MSR 1200 lamp 1-16 to 1-17
rotating lithos 3-19 to 3-21
substitute SV dichroics 1-19 to 1-22
yoke 1-14 to 1-15
Intellabeam 2-2
K
Failure. See Troubleshooting
Fan LED description 1-27
Fan power connectors 3-12
Fans, cleaning 3-3
Features intro-1 to intro-3
Firmware. See Software
Fixed litho wheel 3-7
Fixture number 2-4 to 2-5
Focusing lens 3-5
Front fan access door 1-11
Fuse specifications 3-18
Keyhole slots 3-8, 3-10
L
Lamp
hours 1-24
information counter 1-18
installing or replacing 1-16 to 1-17
ordering 1-7
Index
3
replacing 1-16 to 1-18
strikes 1-24
voltage 1-24
Lamp alignment knobs. See Lamp,
installing or replacing
Lamp box access door 1-11
Lamp LED description 1-27
Lampholder. See Lamp, replacing
LEDs
description 1-27
info 1-24 to 1-25
examples 1-25
Line cord 1-9 to 1-10
Linking fixtures 2-8
LithoPatterns 3-19
ordering 1-7
Lithos
accessories 1-7
cleaning 3-7 to 3-10
ordering 1-7
replacing 3-19 to 3-22
Luminaire intro-1
LWR protocol
description 2-2
implementing 2-3 to 2-5
software uploads A-1
Mechanical zoom lens 3-23
Mirror head deviation 3-24 to 3-25
Model numbers 1-3
Models 1-6
Modes. See DMX, modes
Motor LED description 1-27
Mounting fixtures 2-9 to 2-11
MSD. See MSR 1200 lamp
MSR 1200 lamp
hours 1-24
information counter 1-18
installing or replacing 1-16 to 1-17
LED description 1-27
ordering 1-7
strikes 1-24
voltage 1-24
O
Optical sensors 3-7
Optimizing MSR 1200 lamp. See Lamp,
installing or replacing
Optional accessories 1-7
P
M
Maintenance
cleaning infrared filter, reflectors, and
flags 3-10 to 3-14
cleaning mirror, lenses, motors and
iris 3-4 to 3-6
cleaning the fans 3-3
cleaning wheels and sensors 3-7 to
3-10
general 3-2
installing rotating lithos 3-19 to 3-21
replacing color mixing flags 3-22
replacing dichroics/lithos 3-22
replacing power supply fuses 3-15 to
3-18
replacing rotating lithos 3-19 to 3-21
4
Cyberlight User Manual
Pan invert 1-26
Pan/tilt swap 1-26
Parabolic reflector. See Reflector
Power
fuse specifications 3-18
power cord cap 1-9 to 1-10
replacing fuses 3-15 to 3-18
setting voltage 1-10 to 1-14
specifications 1-4
switch 1-29
turning ON and OFF 1-29
Power lens 3-5
Power supply board 1-13
Problems. See Troubleshooting
Q
Quality Control (QC) plate 1-8
R
Recv LED description 1-27
Reflector 3-13
Replacing
dichroics 3-22
dichroics/lithos 3-22
lithos 3-19 to 3-22
MSR 1200 lamp 1-16 to 1-18
power supply fuses 3-15 to 3-18
rotating lithos 3-19 to 3-21
Rotating litho wheel
factory configuration
CL/SV C-4
CX C-3
ordering lithos 1-7
removing and cleaning lithos 3-14
removing and installing lithos 3-19 to
3-21
S
Specifications
cabling 1-5
electrical 1-4
physical 1-3
power supply fuses 3-18
safety standards 1-4
Static litho wheel
factory configuration
CL/SV C-2
CX C-1
ordering lithos 1-7
replacing lithos 3-22
SV
drawing of 1-6
substituting dichroics 1-19 to 1-22
Switches. See DIP switches
T
Technical support intro-4
Terminators 2-7
Testing the fixture 1-23
Tilt invert 1-26
Trackspot 2-2
Troubleshooting 2-12 to 2-17
Truss 2-10
U
Safety
of fixture mounting 2-9
specifications 1-4
standards 1-4
Safety cables 2-10
ordering 1-7
Self-test 1-23
Sensors 3-7
Setting 1-22
Setting voltage 1-10 to 1-14
Setup mode 1-23
Shutter. See Dim flags.
Software
uploading A-1
version number 1-24
United States Institute of Theatre
Technology. See USITT
Unpacking 1-2
Upgrade. See Uploading software
Uploading software A-1
USITT 2-2
V
Version number 1-24
Voltage rating. See Specifications
Voltage settings 1-10 to 1-14
Index
5
Voltage, reading 1-24
W
Wheels
cleaning 3-7 to 3-10
color, replacing dichroics 3-22
effects C-7
rotating litho, removing and installing
3-19 to 3-21
static litho, replacing lithos 3-22
Wheels, factory configurations
CL/SV color C-6
CL/SV rotating litho C-4
CL/SV static litho C-2
CX color C-5
CX rotating litho C-3
CX static litho C-1
effects C-7
X
XLR cabling
constructing 2-6 to 2-7
ordering 1-7
C-clamps
ordering 1-7
pinouts 2-6, 2-7
terminators 2-7
Xmit LED description 1-27
Y
Yoke
adjusting 3-26
installing 1-14 to 1-15
6
Cyberlight User Manual
Z
Zoom lens 3-5
Zoom lens, CX 3-23

advertisement

Key Features

  • 1200 watt MSR/MSD lamp
  • motorized zoom control
  • 8-position indexed color wheel
  • variable speed rotating lithos
  • variable speed motorized iris control
  • variable high-speed strobe shutter

Frequently Answers and Questions

What are the different models of Cyberlight available?
The Cyberlight family consists of three models: Cyberlight, Cyberlight CX, and Cyberlight SV. The Cyberlight model is the full-featured luminaire, with motorized variable frost from hard edge to soft edge; beam position and movement speed; focus; variable zoom; litho and CYM (cyan-yellow-magenta) color selection; color mixing; variable iris; variable-speed rotating lithos (0-50 RPM); full optical dimming; and automatic cooling system shutdown. Additionally, the fixture accepts stock and custom LithoPatterns, including Psy-Dye high resolution glass gobos, Art Glass and Special Effects lithos. The Cyberlight CX is the value-priced luminaire, with all of the features of the Cyberlight except motorized zoom, color mixing and variable frost. The Cyberlight SV is the quieter-operating, full-featured luminaire.
What type of lamp does the Cyberlight use?
The Cyberlight uses a 1200 watt MSR/MSD lamp with a 5600° Kelvin color temperature and a rated life of 750 hours.
How do I change the voltage of the Cyberlight fixture?
The Cyberlight fixture voltage can be changed by accessing the voltage selection jumpers located on the rear panel of the fixture. This can be done by removing the rear panel screws and gently pulling the rear panel away from the fixture. The voltage selection jumpers are located near the voltage selection wire and connector.

Related manuals

Download PDF

advertisement