BRAWA BR 19.1 steam locomotive Operating Instructions
Below you will find brief information for steam locomotive BR 19.1. This locomotive is based on a Polish express train locomotive that was originally built as Class Pt 31 as part of a “unit locomotive programme”. The locomotive is capable of delivering a high performance with its 1’D1’h2 express train locomotive.
Advertisement
Advertisement
Betriebsanleitung
Dampflokomotive BR 19.1
Am 29. August 1941 erließ das Reichsbahnzentralamt in Berlin einen
Umzeichnungsplan für zahlreiche Lokomotiven, die infolge der Besetzung Polens übernommen wurden. Darunter waren, unter der BR 19.1
eingereiht, 54 bemerkenswerte 1´D1´h2 Schnellzuglokomotiven. Zwölf
Lokomotiven der entsprechenden Bauart waren erst 1940 als 39 1001 bis 39 1012 direkt an die DR geliefert worden und liefen jetzt unter den
Nummern 19 155 bis 19 166. Dabei handelte es sich um eine polnische
Schnellzuglok, die als Gattung Pt 31 ursprünglich im Rahmen eines
"Einheitslokprogramms" in 110 Exemplaren gebaut wurde.
Operating Instructions
Steam locomotive BR 19.1
On 29 August 1941, the central office of the Reichsbahn in Berlin published a reclassification plan for numerous locomotives which were taken over as a result of the occupation of Poland. These included 54 remarkable 1´D1´h2 express train locomotives classified as BR 19.1.
Twelve locomotives of the corresponding construction type had been delivered directly to the DR in 1940 as 39 1001 to 39 1012 and were now in service under the numbers 19 155 to 19 166.
This was a Polish express train locomotive, 110 of which had originally been built as Class Pt 31 as part of a "unit locomotive programme".
1
Inhaltsverzeichnis
Contents
Benennung Seite
Allgemeine Montage- und Sicherheitshinweise ................................. 2
Arbeiten vor der Inbetriebnahme
• Entnahme der Lok aus der Verpackung ......................................... 4
• Zusatzbauteile montieren ............................................................... 4
• Spezialwerkzeug ............................................................................. 5
Wartungsarbeiten
Lokomotive
• 1. Ölen .......................................................................................... 5
• 2. Gehäuse demontieren .............................................................. 6
• 3. Motor tauschen ........................................................................ 6
• 4. Beleuchtungseinrichtung ......................................................... 6
• 5. Wartungsarbeiten an Radsätze, Getriebe, und Kuppelgestänge ................................................................ 6
• 6. Kupplungsnormschacht tauschen ........................................... 6
• 7. Haftreifen tauschen ................................................................. 6
• 8. Schleiferwechsel bei Wechselstromausführung ...................... 6
• 9. Raucheinsatz montieren .......................................................... 6
Tender
• 10. Gehäuse demontieren .............................................................. 8
• 11. Tender von Lok trennen ........................................................... 8
• 12. Platine erneuern/ausbauen ...................................................... 8
• 13. Glühbirnen tauschen ................................................................ 8
• 14 Wartungsarbeiten an Radsätze ................................................ 8
• 15. Kupplungsnormschacht tauschen ........................................... 8
• 16. Premium-Digitaldecoder tauschen .......................................... 8
• 17. Digitalbetrieb ............................................................................ 8
Ersatzteilliste ............................................................................ 14 – 22
Bestellhinweis
• Bestellbeispiel ............................................................................... 23
Funktionstastenbelegung für Soundmodelle .................................... 23
Allgemeine Montage- und Sicherheitshinweise
• Diese Bedienungsanleitung beschreibt sämtliche Arbeitsvorgänge die zur Wartung und Instandhaltung notwendig sind. Bitte lesen Sie diese Bedienungsanleitung bevor Sie mit den Arbeiten beginnen.
• Bei unsachgemäßem Umgang mit elektrischen Bauteilen können diese zerstört werden. Für entsprechende Arbeiten (z.B.
Platinenwech-sel) können Sie sich an Ihren Fachhändler oder den
Hersteller wenden.
• Bei den folgenden Wartungsarbeiten ist die jeweilige Demontage beschrieben, der Zusammenbau ist in umgekehrter Reihenfolge auszuführen.
• Die folgenden Wartungsarbeiten sind bei Gleich- und
Wechselstrom-Ausführungen fast identisch. Im Ausnahmefall wird im entsprechenden Textabschnitt Bezug genommen.
• Jegliche Kabel oder Verbindungsdrähte die in diesem Produkt verbaut sind dürfen nicht in eine Netzsteckdose eingeführt werden.
Lebensgefahr!
• Dieses Modell ist auf märklin-Metallgleisen nur bedingt einsatzfähig.
märklin ist eingetragenes Warenzeichen der "Geb. Märklin & Cie. GmbH Göppingen"
2
Description Page
General assembly and safty information ............................................. 3
Work to be performed before starting up
• Removing the locomotive from the packaging .............................. 4
• Fitting additional parts .................................................................... 4
• Special tool ..................................................................................... 5
Maintenance work
Locomotive
• 1. Lubricating ............................................................................... 5
• 2. Dismantling housing ............................................................... 10
• 3. Exchanging the engine .......................................................... 10
• 4. Light fittings ........................................................................... 10
• 5. Maintenance work on wheelsets, gears, and coupling rods .................................................................. 10
• 6. Replace the standard coupler shaft ...................................... 10
• 7. Replace the traction tires ...................................................... 10
• 8. Replace pic up in alternating current version ........................ 10
• 9. Mounting smoke insert .......................................................... 10
Tender
• 10. Dismantling housing ............................................................... 12
• 11. Disconnect the tender from the locomotive .......................... 12
• 12. Renew/remove the printed circuit board ............................... 12
• 13. Exchanging the light bulbs ..................................................... 12
• 14. Maintenance work on wheelsets ........................................... 12
• 15. Replace the standard coupler shaft ...................................... 12
• 16. Replace the premium digital decoder ................................... 12
• 17. Digital operation ..................................................................... 12
Spare parts list ......................................................................... 14 – 22
Order notice
• Order example .............................................................................. 23
Function keys for sound models ....................................................... 23
General assembly and safety information
• These operating instructions describe all work steps necessary for maintenance and repair. Please read these operating instructions carefully before you start with your work.
• In the case of incorrect handling of electrical components, they may be destroyed. Please ask your specialist dealer to help with the necessary work (e.g. changing circuit boards).
• In the case of maintenance work, the disassembly is described below, to re-assemble the tractor reverse the work steps.
• The maintenance work described below is virtually identical for direct current and alternating current models. If there are any differences these will be pointed out specifically.
• All cables and connection wires installed in this product may not be inserted in a mains socket. Danger!
• This model fits conditionally to märklin metals.
märklin is a registered trademark of the "Geb. Märklin & Cie. GmbH Göppingen"
3
Arbeiten vor der Inbetriebnahme
Work to be performed before starting up
Entnahme der Lok aus der Verpackung (Fig. 1)
Deckel der Verpackung öffnen. Kunststoff-Schutzverpackung mit Lok entnehmen und auf einen Tisch oder ähnliches abstellen.
Lasche (1) lösen, Deckel und Seitenteile der Schutzverpackung wegklappen, Lok entnehmen.
Removing the locomotive from packaging (Fig. 1)
Open package lid. Take out plastics protecting package with engine and put it down on a table or similar item.
Loosen latch (1), fold away lid and side parts of protecting package, take out engine and take out engine.
Fig. 1
1
Zusatzbauteile montieren (Fig. 2)
In der Verpackung sind zusätzliche Bauteile lose beigelegt. Siehe
Seite 14, Pos. 212.
• 2 = 2 x Bügelkupplung
Werden die Bauteile aus dem Zurüstbeutel für Vitrinenmodelle montiert, ist die Lok nicht mehr für den Fahrbetrieb geeignet.
• 1 = 2 x Bremsschlauch Knorr rechts
• 3 = 2 x Bremsschlauch Knorr links
• 4 = 2 x Heizschlauch
• 5 = 2 x Originalkupplung
• 6 = 1 x Aufstieg vorn links
• 7 = 1 x Aufstieg vorn rechts
• 8 = 1 x Trittstufe rechts
• 9 = 1 x Trittstufe links
• 10 = 1 x Leiter links
• 11 = 1 x Leiter rechts
• 12 = 1 x Injektorleitung 1
• 13 = 1 x Injektorleitung 2
Fitting additional parts (Fig. 2)
Accessory parts have been loosely enclosed in the packaging. See page 14, position 212.
• 2 = 2 x Bow coupling
If the components from the add-on bag for display models are mounted, then the engine will no longer be suitable for operation.
• 1 = 2 x Brake hose Knorr right
• 3 = 2 x Brake hose Knorr left
• 4 = 2 x Heating hose
• 5 = 2 x Original coupling
• 6 = 1 x Front step left
• 7 = 1 x Front step right
• 8 = 1 x Step right
• 9 = 1 x Step left
• 10 = 1 x Ladder left
• 11 = 1 x Ladder right
• 12 = 1 x Injection pipe 1
• 13 = 1 x Injection pipe 2
4
Wartungsarbeiten
Maintenance works
Fig. 2
Spezialwerkzeug (Fig. 3)
Mit dem Schraubedreher (1) können die Schrauben (2) der
Kuppelstangen gelöst und wieder befestigt werden.
Special tool (Fig. 3)
With the screwdriver (1) you can dismantle and fasten the screws (2) of the coupling rods.
Fig. 3
2
1
1. Ölen (Fig. 4)
Der Motor und die Lagerstellen der Radsätze können an den gekennzeichneten Punkten sparsam mit Öl der Modellbaubranche geölt werden. Zum Ölen des Motors ist das Gehäuse abzunehmen, siehe Seite 6, Punkt 2.
1. Lubricating (Fig. 4)
The engine and the wheelset bearings may be sparingly lubricated at the marked places with oil used for model making purposes.
In order to lubricate the engine, remove the housing, compare page
10, item 2.
Fig. 4
Motor
Engine
Räder
Wheels
5
Wartungsarbeiten an der Lok
2. Gehäuse demontieren (Fig. 5)
An der Gehäuseunterseite drei Schrauben (80, 111) herausdrehen und
Gehäuse (01) nach oben abnehmen.
3. Motor tauschen (Fig. 5)
Gehäuse (01) demontieren, siehe Punkt 2. Halter für Schnecke (48) ausklipsen und Schnecke (49) mit Kardan (47) nach oben herausnehmen. Platine (159) abnehmen. Schrauben (50) herausdrehen und Motor (46) mit Kesselunterteil
(51) abnehmen. Schrauben (52) herausdrehen und Motor abnehmen.
Verkabelung am Motor ablöten.
Achtung: Beim Ausbau des Motors muss auf die Verkabelung beachtet werden – sonst falsche Fahrtrichtung.
4. Beleuchtungseinrichtung (Fig. 5)
Gehäuse (01) demontieren, siehe Punkt 2.
Glühbirnen vorne: Lampe (121) nach oben abziehen. Glühbirne (13) nach oben herausziehen und Kabel an Platine (159) ablöten. Einbau in umgekehrter
Reihenfolge.
Glühbirne Führerhaus: Befestigungsschraube (21) herausdrehen. Platine (28) abnehmen und das Kabel entfernen. Befestigungsschraube (19) herausdrehen und Führerhaus (07) nach oben abnehmen. Abdeckung (12) abziehen und Glühbirne (13) mit Kabel aus dem Gehäuse herausziehen.
Hinweis: Die Innenbeleuchtung kann im Digitalbetrieb schaltbar gemacht werden. Dazu den Schiebeschalter im Tender umschalten. Jetzt kann mit F2 die Innenbeleuchtung geschaltet werden.
5. Wartungsarbeiten an Radsätze, Getriebe und
Kuppelgestänge (Fig. 5)
Bei Wartungsarbeiten an den Radsätzen (96-98) oder dem unteren Getriebe muss bei Wechselstrommodellen der Schleifer (101) demontiert werden, siehe
Punkt 8. Die Schrauben (81, 110) herausdrehen und die Getriebeabdeckung
(99) abnehmen.
Für Wartungsarbeiten am oberen Getriebe muss das Gehäuse (01) abgenommen werden, siehe Punkt 2. Den Halter für Schnecke (48) ausklipsen und
Schneckenrad (49) mit Kardan (47) entnehmen.
Zum lösen des entsprechenden Radsatzes vom Kuppelgestänge verwenden
Sie bitte den mitgelieferten Schraubendreher, siehe
Seite 5 Spezialwerkzeug.
Der Radsatz (142) kann ohne Demontage des Vorläufers (118) ausgeklipst werden.
Zur Demontage des Radsatz (93) die Schrauben (95) herausdrehen und
Abdeckung mit Federimitation (94) abnehmen.
Die Demontage der Steuerung (141, 142) wird nicht empfohlen, da es sich hier um eine konstruktiv komplexe Mechanik handelt. Falls Sie dennoch das
Kuppelgestänge demontieren, bitten wir Sie genau darauf zu achten, wo und wie jedes Einzelteil montiert war. Die Einbaulage können Sie auch aus der
Ersatzteilgrafik auf Seite 16 entnehmen.
6. Kupplungsnormschacht tauschen (Fig. 5)
Befestigungsschraube (113) herausdrehen und Vorläufer (102) abnehmen.
Bügelkupplung (104) aus Kupplungsnormschacht (103) ausklipsen.
7. Haftreifen tauschen (Fig. 5)
Schraube (68) mit Spezialwerkzeug, siehe Seite 5, herausdrehen. Kuppelstange (71 bzw. 138) zur Seite schieben und Haftreifen (217) wechseln.
8. Schleiferwechsel bei Wechselstromausführung (Fig. 5)
Befestigungsschraube (110) des Schleifers (101) herausdrehen. Kabel am
Schleifer ablöten und Schleifer abnehmen.
9. Raucheinsatz montieren (Fig. 5)
Gehäuse (01) demontieren, siehe Punkt 2.
Raucheinsatz (Pos. 162, Bestell-Nr. 9750.52.03) in Halterung (161) einsetzen und Gehäuse montieren.
6
Fig. 5
7
Wartungsarbeiten am Tender
10. Gehäuse demontieren (Fig. 6)
Die Schrauben (190) herausdrehen und Gehäuse (02) nach oben abnehmen.
11. Tender von Lok trennen (Fig. 6)
Soll der Tender von der Lok getrennt werden, muss die Platine (175) demontiert werden, siehe Punkt 12. Schraube (206) herausdrehen und Tender von der Lok trennen.
12. Platine erneuern/ausbauen (Fig. 6)
Gehäuse demontieren, siehe Punkt 10. Befestigungsschrauben (174) herausdrehen und Platine (175) nach oben abnehmen. Sämtliche
Kabel durch Abziehen der Kabelhalter (166) entfernen. Bitte kennzeichnen Sie sich wo die einzelnen Kabel befestigt waren.
Achtung: Wird die Platine zum Trennen von Tender und Lok ausgebaut, müssen nur die Kabel an der Platine entfernt werden, die am Tender angeschlossen sind.
13. Glühbirnen tauschen (Fig. 6)
Gehäuse demontieren, siehe Punkt 10. Kabel/Kabelhalter (166) der defekten Glühbirne (13) an Platine (175) abziehen.
14. Wartungsarbeiten an Radsätze (Fig. 6)
Entsprechenden Radsatz (194) aus dem Drehgestell (195) ausklipsen.
15. Kupplungsnormschacht tauschen (Fig. 6)
Gehäuse demontieren, siehe Punkt 10. Befestigungsschrauben (174) herausdrehen und Abdeckung (208) abnehmen. Kupplungsnormschacht (224) abnehmen und Bügelkupplung (183) ausklipsen.
16. Premium-Digitaldecoder tauschen (Fig. 6)
Gehäuse demontieren, siehe Punkt 10. Premium-Digitaldecoder (219) abziehen und neuen einstecken.
17. Digitalbetrieb (Fig. 6)
Wechselstrom-Ausführung
Lokomotiven in Wechselstrom-Ausführung AC werden serienmäßig mit
Premium-Digitaldecoder (219) ausgeliefert. Der Decoder erkennt die
Betriebsart (analog/digital) selbstständig. Soll der Decoder umprogrammiert werden, liegt die Einbau- und Betriebsanleitung Premium-
Digitaldecoder bei.
Der Decoder ist werkseitig auf Adresse 03 eingestellt.
Gleichstrom-Ausführung
Gehäuse demontieren, siehe Punkt 10. Blindstecker (176) abziehen und Digitaldecoder einstecken. Den richtigen Einbau des
Digitaldecoders, dessen Einsteckrichtung und Programmierung entnehmen Sie der Betriebsanleitung des Decoderherstellers.
8
Fig. 6
9
Maintenance works on the loco
2. Dismantle housing (Fig. 5)
Unscrew the three screws (80, 111) on the underside of the housing and remove the housing (01) from the top.
3. Replace engine (Fig. 5)
Dismantle the housing (01), see item 2. Unclip the holder for worm gear (48) and remove the worm gear (49) with cardan (47) from the top. Remove the pcb (159). Unscrew the screws (50) and remove the motor (46) with the boiler under cover (51). Unscrew the screws
(52) and remove the motor. Unsolder the wiring on the engine.
Attention: When dismantling the engine, note the wiring layout -
otherwise incorrect direction of travel.
4. Light fittings (Fig. 5)
Dismantle the housing (01), see item 2.
Bulbs front: Remove the lamp (121) from the top. Pull out the bulb
(13) and unsolder the wiring on the printed circuit board (pcb) (159).
Driver's cab bulb: Unscrew the fixing screw (21). Remove the pcb
(28) and remove the cable. Unscrew the fixing screw (19) and remove the driver's cab (07) from the top. Pull off the cover (12) and pull the bulb (13) and cable out of the housing.
Note: The interior lightning may be switchable by digital operating.
Switch the sliding switch at the tender. With F2 the interior
lightning can switched.
5. Maintenance work on wheelsets, gears and
coupling rods (Fig. 5)
The pic up (101) must be removed for maintenance work on the wheelsets (96-98) or the lower gears, see item 8. Unscrew the screws (81, 110) and remove the gears cover (99).
For maintenance work on the upper gears, the housing (01) must be removed, see item 2. Unclip the holder for worm gear (48) and remove the worm gear (49) with cardan (47).
To unscrew the wheelsets from the coupling rods, please use the special tool, see page 5.
The wheelset (142) can also be unclipped without dismantling the bogie (118).
Dismantling the wheelset (93) unscrew the screw (95) and remove the cover with spring imitation (94).
Dismantling the coupling rod (141, 142) is not recommended, as the mechanics are complex. However, if you do dismantle the coupling rods, please precisely note where and how each individual part was fitted. The installation position is also given in the spare parts diagram on page 16.
6. Replace the standard coupling shaft (Fig. 5)
Unscrew the fixing screw (113) and remove the advancing wheel
(102). Unclip the bow coupling (183) from the standard coupling shaft (103).
7. Replace the traction tyres (Fig. 5)
Unscrew the screw (68) with the special tool, see page 5. Push the coupling rod (71 or 138) to the side and replace the traction tyres
(217).
8. Replace pic up in alternating current version (Fig. 5)
Unscrew the fixing screw (110) of the pic up (101), unsolder the cable on the slider and remove the slider.
9. Mounting smoke insert (Fig. 5)
Remove the housing, see section 3. Insert the smoke unit (item 162,
Order No. 9750.52.03) in the holder (161) and fit housing.
1 0
Fig. 5
1 1
Maintenance works on the tender
10. Dismantle housing (Fig. 6)
Unscrew the screws (190) and take out the housing (02) from the top.
11. Disconnect the tender from the locomotive (Fig. 6)
If the tender is to be disconnected from the locomotive, the printed circuit board (175) must be dismantled, see item 12. Unscrew the screw (206) and disconnect the tnder from the locomotive.
12. Renew/remove printed circuit board (Fig. 6)
Dismantle the housing, see item 10. Unscrew the fixing screws (174) and take out the printed circuit board (175) from the top. Remove all cables by pulling off the cable support (166). Please mark where the individual cables were fixed.
Attention: If the printed circuit board is dismantled to disconnect the
tender and locomotive, only the cables at the printed
circuit board which are connected to the tender have to
be removed.
13. Exchanging the light bulbs (Fig. 6)
Dismantle the housing, see item 10. Pulling off the cable/cable support (166) of the damaged bulb (13) at the pcb (175).
14. Maintenance work on wheelsets (Fig. 6)
Unclips the according wheelset (194) from the bogie (195).
15. Replace the standard coupling shaft (Fig. 6)
Dismantle the housing, see item 10. Unscrew the fixing screws (174) and remove the cover (208). Take off the standard coupling shaft
(224) and unclip the bow coupling (183).
16. Replace the premium digital decoder (Fig. 6)
Dismantle the housing, see item 10. Pull off the premium digital decoder (219) and plug in the new one.
17. Digital operation (Fig. 6)
Alternating current version
Locomotives of the alternative current version AC are supplied with a premium digital decoder (219) as a standard. The decoder recognises the type of operation (analog/digital) independently. If the decoder re reprogrammed, refer to the installation and operating instructions for the premium digital decoder.
The decoder is set to address 03 in the factory.
Direct current version
Dismantle the housing, see item 10. Pull off the dummy plug (176) and plug in the digital decoder. Correct installation of the digital
decoder, its plug-in direction and programming are given in the digital decoder manufacturer’s operating instructions.
1 2
Fig. 6
1 3
Ersatzteilliste Dampflokomotive BR 19.1
Spare Parts List Steam engine BR 19.1
Gleichstrom / Wechselstrom
Lokomotive / Locomotive
D.C. current / A.C. current
1 4
1 5
Ersatzteilliste Dampflokomotive BR 19.1
Spare Parts List Steam engine BR 19.1
Gleichstrom / Wechselstrom
Lokomotive / Locomotive
D.C. current / A.C. current
1 6
Gleichstrom / Wechselstrom
Tender / Tender
D.C. current / A.C. current
1 7
Ersatzteilliste Dampflokomotive BR 19.1
Spare Parts List Steam engine BR 19.1
Pos. Bestell Nr.
Benennung
Order no.
Description
1 40400.50.01
Dachentlüftung
2 40400.50.02
Abdeckung
Ventilation
Cover
3 40400.50.03
Griffstange Führerhaus Cabin handle
40404.50.03
Griffstange Führerhaus 40404 Cabin handle 40404
4 40400.50.04
Windabweiser
5 40400.50.05
Seitenfenster
6 40400.50.06
Frontfenster rechts
7 40400.50.07
Führerhaus kpl.
Wind shield
Side window
Front window right
Drivers cabin cpl.
40404.50.07
Führerhaus 40404 kpl.
40408.50.07
Führerhaus 40408 kpl.
40410.50.07
Führerhaus 40410 kpl.
40412.50.07
Führerhaus 40412 kpl.
8 40400.50.08
Frontfenster links
9 40400.50.09
Fenster hinten rechts
10 40400.50.10
Fenster hinten links
11 40400.50.11
Lampenhalter
Drivers cabin 40404 cpl.
Drivers cabin 40408 cpl.
Drivers cabin 40410 cpl.
Drivers cabin 40412 cpl.
Front window links
Rear window right
Rear window links
Holder for lamp
12 40400.50.12
Lampenschirm
13 3268.99.00
Lampe
14 40400.50.13
Handrad
15 40400.50.14
Leitung Stehkessel
16 40400.50.15
Abdeckung
17 40400.50.16
Kessel kpl.
40404.50.16
Kessel 40404 kpl.
40408.50.16
Kessel 40408 kpl.
40410.50.16
Kessel 40410 kpl.
40412.50.16
Kessel 40412 kpl.
18 40400.50.17
Leitung
19 40400.50.18
Schraube
20 40400.50.19
Leitung
21 40400.50.20
Leitung
22 40400.50.21
Handgriff
23 40400.50.22
Griffstange Kessel links
Lamp cover
Bulb
Hand wheel
Pipe cabin
Hatch
Boiler cpl.
Boiler 40404 cpl.
Boiler 40408 cpl.
Boiler 40410 cpl.
Boiler 40412 cpl.
Pipe
Screw
Pipe
Pipe
Handrail
Handrail boiler links
40404.50.22
Griffstange Kessel links 40404 Handrail boiler left 40404
24 40400.50.23
Sandfallrohr 2 links Sandpipe 2 links
25 40400.50.24
Sandfallrohr 1 links
26 40400.50.25
Kesselleiter
Sandpipe 1 links
Boiler ladder
27 40400.50.26
Leitung
28 40400.50.27
Platine
29 40400.50.28
Dampfrohr
30 40400.50.29
Rauchkammertür
Pipe
PCB
Steam pipe
Smoke box door
40404.50.29
Rauchkammertür 40404
40408.50.29
Rauchkammertür 40408
40410.50.29
Rauchkammertür 40410
40412.50.29
Rauchkammertür 40412
Smoke box door 40404
Smoke box door 40408
Smoke box door 40410
Smoke box door 40412
31 40400.50.30
Griffstange Rauchkammertür Handrail smoke box door
32 40400.50.31
Handrad Rauchkammertür Hand wheel smoke box door
33 40400.50.32
Ventil
34 40400.50.33
Leitung
Valve
Pipe
35 40400.50.34
Ventil
40404.50.34
Ventil 40404
36 40400.50.35
Ventil
40404.50.35
Ventil 40404
Valve
Valve 40404
Valve
Vlave 40404
37 40400.50.36
Leitung
38 40400.50.37
Griffstange Kessel rechts
Pipe
Handrail boiler right
40404.50.37
Griffstange Kessel rechts 40404 Handrail boiler right 40404
39 40400.50.38
Ventil Valve
40 40400.50.39
Sandfallrohr 1 rechts
41 40400.50.40
Sandfallrohr 2 rechts
42 40400.50.41
Kamin
43 40400.50.42
Halter f. Sicherheitsventil
44 40400.50.43
Sicherheitsventil
45 40400.50.44
Pfeife
46 40400.50.45
Motor kpl.
47 40400.50.46
Kardan
Sand pipe 1 right
Sand pipe 2 right
Chimney
Holder f savety valve
Savety valve
Whistle
Motor cpl.
Cardan
48 40400.50.47
Halter f. Schnecke
49 40400.50.48
Schnecke kpl.
50 40400.50.49
Schraube
51 40400.50.50
Kesselunterteil
40410.50.50
Kesselunterteil 40410
52 40400.50.51
Schraube
53 40400.50.52
Schraube
Holder f. worm gear
Worm gear cpl.
Screw
Boiler under cover
Boiler under cover 40410
Screw
Screw
1 8
Pos. Bestell Nr.
Benennung
Order no.
Description
54 40400.50.53
Abdeckung
55 40400.50.54
Abdeckung
56 40400.50.55
Umlauf
40404.50.55
Umlauf 40404
40408.50.55
Umlauf 40408
40410.50.55
Umlauf 40410
57 40400.50.56
Abdeckung Umlauf
58 40400.50.57
Leitung 1 Pumpe
59 40400.50.58
Pumpe
60 40400.50.59
Leitung 2 Pumpe
61 40400.50.60
Windleitblech links
40404.50.60
Windleitblech links 40404
40410.50.60
Windleitblech links 40410
62 40400.50.61
Handgriff
63 40400.50.62
Leiter links
40404.50.62
Leiter links 40404
Cover
Cover
Walk way
Walk way 40404
Walk way 40408
Walk way 40410
Cover walk way
Pipe 1 pump
Pump
Pipe 2 pump
Wind shield left
Wind shield left 40404
Wind shield left 40410
Handrail
Ladder left
Ladder left 40404
64 40400.50.63
Injektorleitung 1
40404.50.63
Inlektorleitung 1 40404
65 40400.50.64
Injektorleitung 2
40404.50.64
Injektorleitung 2 40404
66 40400.50.65
Kesselstütze
40404.50.65
Kesselstütze 40404
67 40400.50.66
Halter für Steuerung
40404.50.66
Halter für Steuerung 40404
Injection pipe 1
Injection pipe 1 40404
Injection pipe 2
Injection pipe 2 40404
Boiler support
Boiler support 40404
Crosshead slide bar support
Crosshead slide bar support 40404
68 40400.50.67
Schraube für Kuppelstange
69 40400.50.68
Feder
70 40400.50.69
Abdeckung
71 40400.50.70
Kuppelstange links
Screw for couple rod
Spring
Cover
Couple rod left
72 40400.50.71
Hülse Bush
73 40400.50.72
Kurbelzapfen mit Schwinge links Gear return crank left
74 40400.50.73
Treibstange links
75 40400.50.74
Bremsklotz 4 links
Connecting rod left
Brake block 4 left
40404.50.74
Bremsklotz 4 links 40404
76 40400.50.75
Bremsklotz 3 links
40404.50.75
Bremsklotz 3 links 40404
77 40400.50.76
Bremsklotz 2 links
40404.50.76
Bremsklotz 2 links 40404
79 40400.50.78
Bremsklotz 1 links
40404.50.78
Bremsklotz 1 links 40404
80 40400.50.79
Schraube
81 40400.50.80
Schraube
82 40400.50.81
Schraube
83 40400.50.82
Deichsel
40404.50.82
Deichsel 40404
84 40400.50.83
Welle 1
85 40400.50.84
Welle 2
86 40400.50.85
Zahnrad 1
87 40400.50.86
Zahnrad 2
Brake block 4 left 40404
Brake block 3 left
Brake block 3 left 40404
Brake block 2 left
Brake block 2 left 40404
Brake block 1 left
Brake block 1 left 40404
Screw
Screw
Screw
Shaft
Shaft 40404
Gear shaft 1
Gear shaft 2
Gear 1
Gear 2
88 40400.50.87
Zahnrad
89 40400.50.88
Drehgestell
40404.50.88
Drehgestell 40404
90 40400.50.89
Abdeckung
40404.50.89
Abdeckung 40404
91 40400.50.90
Stütze links
40404.50.90
Stütze links 40404
92 40400.50.91
Feder
Gear
Bogie
Bogie 40404
Cover
Cover 40404
Support left
Support left 40404
Spring
93 40400.50.92
Radsatz DC
40401.50.92
Radsatz AC
40404.50.92
Radsatz DC 40404
40405.50.92
Radsatz AC 40405
Wheelset DC
Wheelset AC
Wheelset DC 40404
Wheelset AC 40405
40408.50.92
Radsatz DC 40408/40410 Wheelset DC 40408/40410
94 40400.50.93
Abdeckung mit Federimitation Cover with spring imitation
40404.50.93
Abdeckung mit Federimitation 40404
Cover with spring imitation 40404
95 40400.50.94
Schraube Screw
96 40400.50.95
Radsatz mit Haftreifennut DC Wheelset with traction tire DC
40401.50.95
Radsatz mit. Haftreifennut AC Wheelset with traction tire AC
40404.50.95
Radsatz mit Haftreifennut DC Wheelset with traction tire DC
40405.50.95
Radsatz mit
Haftreifennut AC 40405
40408.50.95
Radsatz 40408/40410
Wheelset with traction tire AC 40408
Wheelset 40408/40410
1 9
Ersatzteilliste Dampflokomotive BR 19.1
Spare Parts List Steam engine BR 19.1
Pos. Bestell Nr.
Benennung
Order no.
Description
97 40400.50.96
Radsatz DC
40401.50.96
Radsatz AC
40404.50.96
Radsatz DC 40404
40405.50.96
Radsatz AC 40405
40408.50.96
Radsatz 40408/40410
98 40400.50.97
Radsatz DC
40401.50.97
Radsatz AC
40404.50.97
Radsatz DC 40404
40405.50.97
Radsatz AC 40405
40408.50.97
Radsatz 40408/40410
99 40400.50.218 Getriebeabdeckung
40404.50.218 Getriebeabdeckung 40404
100 40400.50.98
Radsatz DC
40401.50.98
Radsatz AC
40404.50.98
Radsatz DC 40404
40405.50.98
Radsatz AC 40405
40408.50.98
Radsatz 40408/40410
101 2225 Schleifer AC
102 40400.50.99
Vorläufer
40404.50.99
Vorläufer 40404
103 40400.50.100 Kupplungsschacht
40404.50.100 Kupplungsschacht 40404
104 40400.50.101 Abdeckung
105 40400.50.102 Abdeckung
106 40400.50.103 Schraube
107 40400.50.104 Abdeckung
108 40400.50.105 Schraube
109 40400.50.106 Stütze rechts
40404.50.106 Stütze rechts 40404
110 40400.50.107 Schraube
111 40400.50.108 Schraube
112 40400.50.109 Schraube
113 40400.50.110 Schraube
114 40400.50.111 Aufstieg vorn links
40404.50.111 Aufstieg vorn links 40404
115 40400.50.112 Puffergriff vorn
116 40400.50.113 Abdeckung
117 40400.50.114 Schraube
118 40400.50.115 Aufstieg vorn rechts
40404.50.115 Aufstieg vorn rechts 40404
119 40400.50.116 Puffer links
40404.50.116 Puffer links 40404
120 40400.50.117 Puffer rechts
40404.50.117 Puffer rechts 40404
121 40400.50.118 Lampe für 40400
40404.50.118 Lampe für 40404
40408.50.118 Lampe für 40408
40412.50.118 Lampe für 40412
Screw
Front step left
Front step left 40404
Buffer handle front
Cover
Screw
Front step right
Front step left 40404
Buffer left
Buffer left 40404
Buffer right
Buffer right 40404
Lamp for 40400
Lamp for 40404
Lamp for 40408
Lamp for 40412
122 40400.50.119 Abdeckung
123 40400.50.120 Abdeckung
124 40400.50.121 Abdeckung
125 40400.50.122 Leitung
126 40400.50.123 Zylinder links
40404.50.123 Zylinder links 40404
40410.50.123 Zylinder links 40410
127 40400.50.124 Abdeckung
Cover
Cover
Cover
Pipe
Cylinder left
Cylinder left 40404
Cylinder left 40410
Cover
128 40400.50.125 Abdeckung
129 40400.50.126 Kolbenstangenschutzrohr
Cover
Pisten rod cover pipe
130 40400.50.127 Luftventil Air valve
131 40400.50.128 Zylinderentwässerung links Cylinder drain cocks left
133 40400.50.130 Feder
134 40400.50.131 Bremsklotz 1 rechts
40404.50.131 Bremsklotz 1 rechts 40404
135 40400.50.132 Bremsklotz 2 rechts
Spring
Brake block 1 right
Brake block 1 right 40404
Brake block 2 right
40404.50.132 Bremsklotz 2 rechts 40404
136 40400.50.133 Bremsklotz 3 rechts
40404.50.134 Bremsklotz 3 rechts 40404
137 40400.50.134 Bremsklotz 4 rechts
40404.50.134 Bremsklotz 4 rechts 40404
138 40400.50.135 Kuppelstange rechts
139 40400.50.136 Treibstange rechts
Brake block 2 right 40404
Brake block 3 right
Brake block 3 right 40404
Brake block 4 right
Brake block 4 right 40404
Couple rod right
Connecting rod right
Wheelset DC
Wheelset AC
Wheelset DC 40404
Wheelset AC 40405
Wheelset 40408/40410
Wheelset DC
Wheelset AC
Wheelset DC 40404
Wheelset AC 40405
Wheelset 40408/40410
Gear box cover
Gear box cover 40404
Wheelset DC
Wheelset AC
Wheelset DC 40404
Wheelset AC 40405
Wheelset 40408/40410
Pic up AC
Advancing wheel
Advancing wheel 40404
Standard coupling shaft
Standard coupling shaft 40404
Cover
Cover
Screw
Cover
Screw
Support right
Support right 40404
Screw
Screw
Screw
2 0
Pos. Bestell Nr.
Benennung
Order no.
Description
140 40400.50.137 Kurbelzapfen mit Schwinge rechts
141 40400.50.138 Steuerung kpl. links
142 40400.50.139 Steuerung kpl. rechts
Gear return crank right
Linkage cpl. left
Linkage cpl. right
143 40400.50.140 Zylinderentwässerung rechts Cylinder drain cocks right
144 40400.50.141 Tachometer Speedometer
40404.50.141 Tachometer 40404
145 40400.50.142 Leiter rechts
Speedometer 40404
Ladder right
40404.50.142 Leiter rechts 40404
146 40400.50.143 Drahtbügel für Lampe
Ladder right 40404
Link for lamp
40404.50.143 Drahtbügel für Lampe 40404 Link for lamp 40404
147 40400.50.144 Trittstufe Step
148 40400.50.145 Trittstufe rechts
149 40400.50.146 Trittstufe links
150 40400.50.147 Luftkessel
40404.50.147 Luftkessel 40404
Step right
Step left
Airtank
Airtank 40404
151 40400.50.148 Kesselstütze
40404.50.148 Kesselstütze 40404
152 40400.50.149 Welle
153 40400.50.150 Kesselstütze
40404.50.150 Kesselstütze 40404
154 40400.50.151 Windleitblech rechts
40404.50.151 Windleitblech rechts 40404
40410.50.151 Windleitblech rechts 40410
156 40400.50.153 Lichtmaschine
157 40400.50.154 Leitung
158 40400.50.155 Steuerstange
159 40400.50.156 Platine
160 40400.50.157 Kontaktfeder
161 40400.50.158 Halter f. Raucheinsatz
162 9750.52.03
Raucheinsatz
163 40400.50.159 Kohleeinsatz kpl.
Boiler support
Boiler support 40404
Axle
Boiler support
Boiler support 40404
Windshield right
Wind shield right 40404
Wind shield right 40410
Dynamo
Pipe
Reversing rod
PCB
Contact spring
Holder f. smoke
Smoke unit
Coal box cpl.
40408.50.159 Kohleeinsatz kpl. 40408
40410.50.159 Kohleeinsatz kpl. 40410
164 40400.50.160 Haken
40410.50.160 Haken 40410
165 40400.50.161 Griffstange rechts
40404.50.161 Griffstange rechts 40404
166 40400.50.162 Kabelhalter
167 40400.50.163 Trittstufe
168 40400.50.164 Trittstufe klein rechts
169 40400.50.165 Trittstufe klein links
170 40400.50.166 Werkzeugkasten
40408.50.166 Werkzeugkasten 40408
40410.50.166 Werkzeugkasten 40410
172 40400.50.168 Griffstange links
40404.50.168 Griffstange links 40404
173 40400.50.169 Tendergehäuse
Coal box cpl. 40408
Coal box cpl. 40410
Hook
Hook 40410
Handrail right
Handrail right 40404
Cable support
Step
Step small right
Step small left
Tool box
Tool box 40408
Tool box 40410
Handrail left
Handrail left 40404
Tender body
40404.50.169 Tendergehäuse 40404
40408.50.169 Tendergehäuse 40408
40410.50.169 Tendergehäuse 40410
174 40400.50.170 Schraube
175 40400.50.171 Platine
176 40400.50.172 Brückenstecker
177 40400.50.173 Halter für Lautsprecher
178 40400.50.174 Schallkapsel
Tender body 40404
Tender body 40408
Tender body 40410
Screw
PCB
Blind plug
Holder for speaker
Sound saggar
179 40400.50.175 Abdeckung
180 40400.50.176 Abdeckung
181 40400.50.177 Tenderfahrgestell
40404.50.177 Tenderfahrgestell 40404
Cover
Cover
Tender chassis
Tender chassis 40404
40408.50.177 Tenderfahrgestell 40408
40410.50.177 Tenderfahrgestell 40410
Tender chassis 40408
Tender chassis 40410
182 40400.50.178 Schienenräumer Tender rechts Track cleaner right
40404.50.178 Schienenräumer Tender rechts Track cleaner right
183 9952.50.03
Bügelkupplung
184 40400.50.179 Abdeckung
Bow coupler
Cover
185 40400.50.180 Schienenräumer Tender links Track cleaner left
40404.50.180 Schienenräumer Track cleaner left 40404
Tender links 40404
186 40400.50.181 Aufstieg Tender hinten Step tender rear
40404.50.181 Aufstieg Tender hinten 40404 Step tender rear 40404
2 1
Ersatzteilliste Dampflokomotive BR 19.1
Spare Parts List Steam engine BR 19.1
Pos. Bestell Nr.
Benennung
Order no.
Description
187 40400.50.182 Halterung
40404.50.182 Halterung 40404
188 40400.50.183 Schalter
189 40400.50.184 Leiter Tender vorn links
Holder
Holder 40404
Switch
Ladder tender front left
40404.50.184 Leiter Tender vorn links 40404 Ladder tender front left 40404
190 40400.50.185 Schraube Screw
191 40400.50.186 Leitung Tender
40404.50.186 Leitung Tender 40404
Pipe tender
Pipe tender 40404
192 40400.50.187 Tenderdetail
40404.50.187 Tenderdetail 40404
193 40400.50.188 Bremseinrichtung
40404.50.188 Bremseinrichtung 40404
194 40400.50.189 Radsatz Tender DC
40401.50.189 Radsatz Tender AC
40404.50.189 Radsatz Tender DC 40404
40405.50.189 Radsatz Tender AC 40405
Detail tender
Detail tender 40404
Brake unit
Brake unit 40404
Wheelset tender DC
Wheelset tender AC
Wheelset tender DC 40404
Wheelset tender AC 40405
40408.50.189 Radsatz
Tender DC 40408/40410
195 40400.50.190 Drehgestell Tender
40404.50.190 Drehgestell Tender 40404
196 40400.50.191 Drehgestellfeder 1
40404.50.191 Drehgestellfeder 1 40404
197 40400.50.192 Drehgestellfeder 2
40404.50.192 Drehgestellfeder 2 40404
198 40400.50.193 Bremsblock links
40404.50.193 Bremsblock links 40404
199 40400.50.194 Bremsblock rechts
40404.50.194 Bremsblock rechts 40404
200 40400.50.195 Luftkessel
40404.50.195 Luftkessel 40404
201 40400.50.196 Leitung
202 40400.50.197 Bremsventil
Wheelset tender DC 40408/40410
Bogie tender
Bogie tender 40404
Bogie spring 1
Bogie spring 1 40404
Bogie spring 2
Bogie spring 2 40404
Brake block left
Brake block left 40404
Brake block right
Brake block right 40404
Airtank
Airtank 40404
Pipe
Brake valve
40404.50.197 Bremsventil 40404
203 40400.50.198 Werkzeugkiste
40410.50.198 Werkzeugkiste 40410
204 40400.50.199 Signalhalter
Brake valve 40404
Tool box
Tool box 40410
Signal holder
205 40400.50.200 Leiter Tender vo. rechts Ladder tender fr. right
40404.50.200 Leiter Tender vo. rechts 40404 Ladder tender fr. Right 40404
206 40400.50.201 Schraube
207 40400.50.202 Abdeckung
Screw
Cover
208 40400.50.203 Abdeckung
209 9750.51.93
Lautsprecher
210 40400.50.204 Türe links kpl.
40410.50.204 Türe links kpl. 40410
211 40400.50.205 Türe rechts kpl.
40410.50.205 Türe rechts kpl. 40410
212 40400.50.206 Zurüstbeutel
213 40400.50.207 Werkzeugkiste
Cover
Speaker
Door left cpl.
Door left cpl. 40410
Door right cpl.
Door right cpl. 40410
Add on part
Toolbox
214 40400.50.208 Feder
215 40400.50.209 Schraube
216 40400.50.210 Puffergriff Tender
217 40400.50.211 Haftreifen
218 40400.50.212 Werkzeugkiste auf Umlauf
219 9750.50.80
Digitaldecoder
220 40400.50.213 Zylinder rechts
40404.50.213 Zylinder rechts 40404
40410.50.213 Zylinder rechts 40410
221 40400.50.214 Trittstufe links
40404.50.214 Trittstufe links 40404
222 40400.50.215 Trittstufe rechts
40404.50.215 Trittstufe rechts 40404
223 40400.50.216 Schraube
224 40400.50.217 Kupplungsschacht
40404.50.217 Kupplungsschacht 40404
225 40400.50.218 Schraube
226 40400.50.220 Handbremse
227 40400.50.221 Griffstange links
40404.50.221 Griffstange links 40404
228 40400.50.222 Griffstange rechts
40404.50.222 Griffstange rechts 40404
Spring
Screw
Buffer handle tender
Traction tyre
Box on walkway
Digital decoder
Cylinder rechts
Cylinder right 40404
Cylinder right 40410
Step left
Step left 40404
Step right
Step ri 40404
Screw
Coupler pocket
Coupler pocket 40404
Screw
Hand brake
Handrail left
Handrail left 40404
Handrail right
Handrail right 40404
2 2
Bestellhinweis
Bei der Bestellung von Ersatzteilen muss die Ersatzteil Bestell-Nr. und die Benennung angegeben werden. Ist dies nicht der Fall, kann die Bestellung nicht bearbeitet werden.
Order notice
When ordering spare parts you must always state the order number and give the description. If you do not do this, the order cannot be processed.
Bestellbeispiel:
Position (46), Motor kpl. = 40400.50.45, Motor kpl.
Order example:
Position (46), Motor cpl. = 40400.50.45, Motor cpl.
Optionale Soundfunktion / optional sound functions
F0 Licht AN/AUS
F1 Sound AN/AUS
F2 Signalhorn lang
F3 Glocke
F4 Rauchgenerator
F5 Injektor
F6 Rangiergang
F7 Luftpumpe
F8 Kohle schaufeln
F9 Bremse lösen
F10 Sanden
F11 Signalhorn kurz
Light ON/OFF
Sound ON/OFF
Whistle long
Bell
Smoke generator
Injector
Shunting mode
Air pump
Coal shoveling
Break release
Sanding
Whistle short
Maßstabs- und originalgetreue Kleinmodelle für erwachsene
Sammler.
Scale and true to original small-sized model for adult collectors.
Zum Betrieb des vorliegenden Produkts darf als Spannungsquelle nur ein nach VDE 0551/EN 60742 gefertigter
Spielzeug-Transformator verwendet werden.
Only a toy transformer produced compliant with VDE 0551/
EN 60742 may be used as a voltage source to operate this product.
Dieses Produkt entspricht den gültigen CE Normen.
This product conforms to the current CE standards.
Elektro- und Elektronikaltgeräte dürfen nicht in den
Hausmüll gelangen. Sie müssen entsprechend der jeweils gültigen Länderrichtlinien fachgerecht entsorgt werden.
Electrical equipment may not reach to domestic waste.
According to the current terms of the country reference the electrical eqipment must professional disposed.
2 3
Brawa Artur Braun Modellspielwarenfabrik GmbH & Co.
Uferstraße 26-28 · D-73630 Remshalden
Hotline +49 (0) 7151 - 979 35 68
Telefax +49 (0) 7151 - 746 62 www.brawa.de

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 1'D1'h2 express train locomotive
- Polish origin
- built as Class Pt 31
- part of a "unit locomotive programme"
- 110 examples built
- delivered directly to the DR in 1940
- now in service under the numbers 19 155 to 19 166