One Touch Y280 USER GUIDE

One Touch Y280 USER GUIDE
1
Safety Precautions
Read the safety precautions carefully to ensure the correct and safe use of your
wireless device.
Do not switch on your device when the device use is prohibited or when
the device use may cause interference or danger.
Follow the rules or regulations in hospitals and health care facilities.
Switch off your device near medical apparatus.
Switch off your device in an aircraft. The device may cause interference
to control signals of the aircraft.
Switch off your device near high-precision electronic devices. The
device may affect the performance of these devices.
Do not attempt to disassemble your device or its accessories. Only
qualified personnel are allowed to service or repair the device.
Do not place your device or its accessories in containers with strong
electromagnetic field.
Do not place magnetic storage media near your device. Radiation from
the device may erase the information stored on them.
Do not put your device in a high-temperature place or use it in a place
with flammable gas such as a gas station.
Keep your device and its accessories away from children. Do not allow
children to use your device without guidance.
Use approved chargers only to avoid explosion.
Observe the laws or regulations on device use. Respect others’ privacy
and legal rights when using your device.
It is recommended that the equipment only be used in the environment where
temperature is between-10℃ and 50℃ and humidity is between 10% to 90%. Keep
the equipment in the environment where temperature is between -10℃ and 70℃ or
humidity is between 10% to 90%.
2
Content
Safety Precautions .................................................................................................. 2
1. Web UI configuration .......................................................................................... 4
1.1 login the configuration page ............................................................................ 4
1.2 Icon description................................................................................................. 4
2. Connection .......................................................................................................... 4
2.1 Connection status ............................................................................................. 4
2.2 Profile management .......................................................................................... 5
2.3 Network .............................................................................................................. 6
2.4 PIN Code management ..................................................................................... 6
2.5 Connection Mode .............................................................................................. 6
3. SMS ...................................................................................................................... 6
4. Settings ................................................................................................................ 7
4.1 Language ........................................................................................................... 8
4.2 System ............................................................................................................... 8
5. Warranty .............................................................................................................. 8
6. FAQs .................................................................................................................... 9
7. Certification ....................................................................................................... 11
3
1. Web UI configuration
1.1 login the configuration page
Open the browser, and then input the address http://192.168.1.1.
The default login password is admin.
1.2 Icon description
The icon description as bellow:
The icon description as bellow:
Category
Icon Display
Signal Strength
Connection
Status
SMS
From no signal to excellent
Disconnect
Connected
No Unread SMS,
New Received SMS,
SMS is full
Online update
2. Connection
You can move the mouse to "Connection" and click the items you want. In this section,
the following items are included:

Connection Status: current connection, WAN status

Profile management: manage account settings, Which includes your preferred
network connection as well as the Access Point Name (APN).

Network: choose and set up preferred network settings.

PIN Code management: manage PIN, enable/disable/change/verify.

Connection Mode: Set the dial mode of this device, default is AUTO.
2.1 Connection status




Active profile: Select the profile you want to use from the drop down box.
Connection Status: display the network is connected or disconnected;
Usage: Display usage data
Duration: the duration for current connection;
4
WAN status




Network name: the network name you are using;
Network type: GPRS/EDGE/UMTS/HSDPA/HSUPA/HSPA+/LTE
Roaming: display whether you are in roaming network or not;
IP address: this is the IP address arranged for this device.
Usage History
Click link of Usage History, will display current data and total data of usage.




Usage: Display usage data
Upload: Display upload usage data
Download: Display download usage data
Duration: Display duration time
2.2 Profile management
Add a new profile:
1, Click <New>.
2, Input the correct parameters you get from the operator.
Note: Profile Name/Number/APN is the mandatory to be filled.
3, Click <Save>.
Edit a profile:
1, Select the profile from the connection profile list.
2, Change the parameters.
3, Click <Save>.
Delete a profile:
1, Select the profile from the connection profile list.
2, Click <Delete>.
3, On the pop up dialog ”are you sure to delete this profile?”,click <OK>.
Note: the default profile can not be deleted.
Set as default:
1, Select the profile from the connection profile list.
2, Click <Set default>.
3, On the pop up dialog ”are you sure to set this profile as default?”, click <OK>.
Note: Once set the profile as default,(D) will be added as a mark.
5
2.3 Network
 Network Mode:Automatic/4G only/3G only/2G only, default is automatic.
 Network Selection: Automatic/Manual, default is automatic.
Select a Network Manually
1,Choose Manual in the network selection.
2,Click <Apply>.
3,Click <Refresh> to list the available network.
4,Choose the network and Click <Select> to register.
Note: For the Services, LTE, UMTS, GSM. For the Status, Active( the network
registered), Available( the network can be used).
2.4 PIN Code management
Enable PIN
1, When PIN is disable, click <Enable>, PIN input page is displayed.
2, Enter the PIN you want to set, only number is accepted.
3,Click <Apply>.
Disable PIN
1, When PIN is enable, click <Disable>, PIN input page is displayed;
2,Enter the correct PIN;
3,Click <Apply>;
Change PIN
1, When PIN is enable, click <Change PIN>,PIN input page is displayed;
2,Enter the Old PIN/New PIN/Confirm PIN;
3,Click <Apply>;
Note: when you entered wrong PIN 3 times, PUK is needed, you can get this key from
the operator.
2.5 Connection Mode
Auto connect in roaming:
3. SMS
You can move the mouse to "SMS" and click the items you want. In this section, the
following items are included:

New: write the new SMS.

Read: list the SMS received.
6



Sent: list the SMS sent successfully.
Draft: save the SMS not sent or sent failed.
SMS settings: set the SMS center number and the SMS saved location .
Read SMS
Left click the content of the SMS to read.
Sent SMS
1,Move the mouse to “SMS”.
2,Left click “New”.
3,Input the number and the content.
4,Click <Sent>.
Forward SMS
1,Left click the content of the SMS you want to forward.
2,Click <Forward>.
3,Input the number.
4,Click <Sent>.
Reply SMS
1,Left click the content of the SMS you want to reply.
2,Click <Reply>.
3,Input the content.
4,Click <Sent>.
Delete SMS
1,Left click the Mark of the SMS you want to delete.
2,Click <Delete>.
Delete all SMS
1,Click <Mark All>.
2, Click <Delete>.
SMS settings
SMS Center Number: You can get it from your operator;
SMS Save Mode: the location SMS stored, default is Device;
4. Settings
You can move the mouse to "Settings" and click the items you want. In this section,
the following items are included:
7


Language: set the language displayed on the web UI.
System: display the device info, save & restore the configuration.
4.1 Language
Change language:
1,Choose the language,
;
2, Click <Apply>.
4.2 System
Reboot
Click <Reboot> to restart the device.
Reset
Reset the device to the original factory settings. you can also use the hardware reset
button under the back cover, marked with Reset.
5. Warranty

The device is warranted against any deviation from technical specifications for a
period of twelve (12) months from the date specified on your original invoice1.

Under the terms of this warranty, you must immediately inform your vendor in
case of a conformity defect on this device, and present a proof of purchase.

The vendor or repair center will decide whether to replace or repair this device, as
appropriate.

Repaired or replaced this device are warranted ONE (1) month unless there are
statutory provisions to the contrary.

This warranty shall not apply to damage or defects to this device due to:
1)
Not following the instructions for use or installation,
2)
Not being compliant with technical and safety standards applicable in the
geographical area where this device is used,
3)
Improper maintenance of sources of energy, and of the overall electric
installation,
1 The mandatory warranty period may vary if overriding statutory provisions are applicable in
your jurisdiction.
8
4)
Accidents or consequences of theft of the vehicle in which this device is
transported, acts of vandalism, lightning, fire, humidity, infiltration of liquids,
inclement weather,
5)
Connecting to or integrating into this device any equipment not supplied or not
recommended by the manufacturer,
6)
Any servicing, modification or repair performed by individuals not authorised by
the manufacturer, the vendor or the approved maintenance centre,
7)
Use of this device for a purpose other than that for which it was designed,
8)
Malfunctions caused by external causes (e.g., radio interference from other
equipment, power voltage fluctuations),
9)
Faulty connections resulting from unsatisfactory radio transmission or caused by
the absence of radio relay coverage.

Warranty is also excluded for this device on which markings or serial numbers
have been removed or altered.

This device is also warranted against hidden defects (defects inherent in the
design, manufacture, etc.).

There are no other express warranties than this printed limited warranty,
expressed or implied, of any nature whatsoever.

In no event shall the manufacturer be liable for incidental or consequential
damages of any nature whatsoever, including but not limited to trading loss,
commercial loss, to the full extent those damages can be disclaimed by law. Some
countries/states do not allow the exclusion or limitation of incidental or
consequential damages, or limitation of the duration of implied warranties, so the
preceding limitations or exclusions may not apply to you.
6. FAQs
1. Q:
A:
2. Q:
A:
Which browser does the device support?
It supports Firefox, Safari 4.0.2-5. 2, IE 7.0-10.0, Opera; Chrome;
Which operation systems does the software support?
It supports Windows XP, Windows Vista, Windows 7, Windows 8 and Mac
OS X 10.5-10.8
9
3. Q:
A:
4. Q:
A:
I cannot install the driver automatically.
Find the AutoRun.exe file in modem’s root and double-click it to run.
Why the LED indicator of device is always in solid red?
The status for solid red LED indicator may be:
1. No service;
2.
No SIM card;
3.
SIM Error
You may need:
5.
1.
Check network signal;
2.
Insert a SIM card;
3.
Check SIM card status.
Q: The SIM/USIM card does not register any networks
A: The reasons are shown below:
1. Unstable local signal;
2. The software is an old version;
3. Hardware problem.
You may:
1. Try to logon from another location;
2. Update the software;
3. Check the hardware or use another data card and retry.
6.
Q: Why does the prompt “No available connection profile. Please set an
available default one in connection profile” appear?
A: Please add a connection profile manually.
7.
Q: It failed to connect to the internet
A: Please make sure the connection profile and settings are correct.
8.
Q: The connection speed and data transfer rates are too slow
A: Please check the local network signal strength.
9.
Q: Sending an SMS failed
A: Please make sure the SMS center number is correct.
10. Q: I cannot receive an SMS
A: Please check whether your SIM/USIM card’s memory is full.
10
11. Q: Does it support roaming?
A: This depends on the local operator. Please check with your local operator or
service provider
7. Certification
This product meets applicable national SAR limits of 2.0W/kg.
The specific maximum SAR values can be found in the following section of
this user guide.
www.sar-tick.com
When carrying the product or using it while worn on your body, either use an
approved accessory such as a holster or otherwise maintain a distance of
5mm from the body to ensure compliance with RF exposure requirements.
Note that the product may be transmitting even if you are not making a phone
call.
CE:
Proof of compliance with international standards (ICNIRP) or with European
Directive 1999/5/EC (R&TTE) is required of all Modem models before they can be put
on the market. The protection of the health and safety for the user and any other
person is an essential requirement of these standards or this directive.
THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO
WAVES.
The USB-Modem is a radio transmitter and receiver. It is designed not to exceed the
limits for exposure to radio waves (radio frequency electromagnetic fields)
recommended by international guidelines. The guidelines were developed by an
independent scientific organization (ICNIRP) and include a substantial safety margin
designed to assure the safety of all persons, regardless of age and health.
The radio wave exposure guidelines use a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit for mobile devices is 2 W/kg.
Tests for SAR are conducted using standard operating positions with the device
transmitting at its highest certified power level in all tested frequency bands. The
highest SAR values under the ICNIRP guidelines for this device model are:
11
Maximum SAR for this model and conditions under which it was recorded.
Body SAR
LTE 1800
1.224
During use, the actual SAR values for this device are usually well below the values
stated above. This is because, for purposes of system efficiency and to minimize
interference on the network, the operating power of your mobile device is
automatically decreased when full power is not needed for the call. The lower the
power output of the device, the lower its SAR value.
Body-worn SAR testing has been carried out at a separation distance of 5mm. To
meet RF exposure guidelines during body-worn operation, the device should be
positioned at least this distance away from the body.
If you are not using an
approved accessory ensure that whatever product is used is free of any metal and
that it positions the phone the indicated distance away from the body.
The World Health Organization has stated that present scientific information does not
indicate the need for any special precautions for the use of mobile devices. They
recommend that if you are interested in further reducing your exposure then you can
easily do so by limiting your usage or keep the device away from the head and body.
For more information you can go to www.alcatelonetouch.com
Additional information about electromagnetic fields and public health are available on
the following site: http://www.who.int/peh-emf
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising