Auto SmartPort Macro

C H A P T E R

17

Configuring Auto SmartPort Macros

This chapter describes how to configure and apply Auto SmartPort macros on the Catalyst 4500 series switch.

This chapter includes the following major sections:

•

•

•

About Auto SmartPorts, page 17-1

Configuring Auto SmartPorts, page 17-2

Displaying Auto SmartPorts, page 17-13

Note

For complete syntax and usage information for the switch commands used in this chapter, look at the

Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location: http://www.cisco.com/en/US/products/hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Command Reference, it is located in the larger Cisco

IOS library. Refer to the Cisco IOS Command Reference and related publications at this location: http://www.cisco.com/en/US/products/ps6350/index.html

About Auto SmartPorts

Auto SmartPort macros dynamically configure ports based on the device type detected on the port. When the switch detects a new device on a port, it applies the appropriate Auto SmartPorts macro. When a link-down event occurs on the port, the switch removes the macro. For example, when you connect a

Cisco IP phone to a port, Auto SmartPorts automatically applies the Cisco IP phone macro. The Cisco

IP phone macro enables quality of service (QoS), security features, and a dedicated voice VLAN to ensure proper treatment of delay-sensitive voice traffic.

Auto SmartPorts uses event triggers to map devices to macros. The most common event triggers are based on Cisco Discovery Protocol (CDP) messages received from connected devices. The detection of a device (Cisco IP phone, Cisco wireless access point, Cisco switch, or Cisco router) invokes an event trigger for that device.

Link Layer Discovery Protocol (LLDP) is used to detect devices that do not support CDP. Other mechanisms used as event triggers include the 802.1X authentication result and MAC-address learned.

System built-in event triggers exist for various devices based mostly on CDP and LLDP messages

(

Table 17-1

) and some MAC address. These triggers are enabled as long as Auto SmartPort is enabled.

OL-22170-01

Catalyst 4500 Switch Software Configuration Guide

17-1

Chapter 17 Configuring Auto SmartPort Macros

Configuring Auto SmartPorts

You can also define your own trigger. User-defined triggers can be CDP/LLDP-based, a group of MAC addresses, or the value of the attribute-value (AV) pair for the auto-smart-port keyword.

The Auto SmartPort macros are groups of CLI commands. Detection of devices on a port triggers the application of the macro for the device. (For example, detecting a CISCO_PHONE event on a port triggers the switch to apply the commands in the CISCO_PHONE_AUTO_SMARTPORT macro.)

System built-in macros exist for various devices, and, by default, system built-in triggers are mapped to the corresponding built-in macros. You can change the mapping of built-in triggers or macros as needed.

A macro basically applies or removes a set of CLIs on an interface based on the link status. In a macro, the link status is checked. If the link is up, then a set of CLIs is applied; if the link is down, the set is removed (the no format of the CLIs are applied). The part of the macro that applies the set of CLIs is termed macro. The part that removes the CLIs (the no format of the CLIs) are termed antimacro.

Besides creating user-defined triggers, you can also create user-defined macros and map one to the other among all triggers (both built-in and user-defined) and all macros (both built-in and user-defined). Use the Cisco IOS scripting capability to create the macros. Cisco IOS scripting is a BASH-like language syntax for command automation and variable replacement.

The four detection mechanisms adhere to the following order of priority:

•

•

If 802.1X authentication is configured on a port, an authentication response-based trigger is applied, and other triggers are ignored.

If 802.1X authentication fails and the CDP/LLDP fallback mechanism is configured, CDP/LLDP triggers for phone devices only; if no fallback mechanism is configured, or a device is not a phone device, nothing is triggered.

•

•

If 802.1X authentication is configured on a port, a MAC address-based trigger is never triggered.

If 802.1X authentication is not configured on a port, CDP/LLDP has priority over a MAC address-based trigger with a hold-off timer applied for MAC-address based trigger. Between

CDP/LLDP, there is no particular order; whichever one arrives first is triggered.


The following topics are included:

•

•

•

•

•

•

Enabling Auto SmartPorts, page 17-2

Auto SmartPorts Configuration Guidelines, page 17-4

Configuring Auto SmartPorts Built-in Macro Parameters, page 17-6

Configuring User-Defined Event Triggers, page 17-7

Configuring Mapping Between User-Defined Triggers and Built-in Macros, page 17-9

Configuring Auto SmartPorts User-Defined Macros, page 17-9

Enabling Auto SmartPorts

17-2

Note

By default, Auto SmartPort is disabled globally. To disable Auto SmartPorts macros on a specific port, use the no macro auto global processing interface command before enabling Auto SmartPort globally.

To enable Auto SmartPort globally, use the macro auto global processing global configuration command.


OL-22170-01


To enable Auto SmartPorts, perform this task:


Command

Step 1

Switch# configure terminal

Step 2

Switch(config)# [no] macro auto

global processing

[fallback [cdp |

lldp

]]]

Step 3

Switch(config)# end

Step 4

Switch# show running-config

Step 5

Switch# copy running-config

startup-config

Purpose

Enters global configuration mode.

Enables Auto SmartPorts on the switch globally.

The fallback option allows you to enable the switch to use CDP or LLDP as a trigger when the port is configured with 802.1X and authentication fails.

Note

The fallback options only work for phone devices.

Use the no macro auto global processing fallback command to disable the fallback mechanism, but still have Auto SmartPort enabled.

Use no macro auto global processing to disable Auto SmartPort globally.

Note

The macro auto processing command turns Auto SmartPort on or off on the interface level. The default is on.

Returns to privileged EXEC mode.

Verifies that Auto SmartPorts is enabled.

(Optional) Saves your entries in the configuration file.

Use the show shell functions and the show shell triggers privileged EXEC command to display the event triggers, the built-in macros, and the built-in macro default values.

This example shows how enable Auto SmartPorts on the switch and how to disable the feature on a specific interface:

Switch(config)# macro auto global processing

Switch(config)# interface interface_id

Switch(config-if)# no macro auto processing

Auto SmartPorts Default Configuration

By default, Cisco IOS shell is enabled and Auto SmartPorts is disabled globally.

Table 17-1

shows the Auto SmartPorts built-in event triggers that are embedded in the switch software by default.

Table 17-1 Auto SmartPorts Built-in Event Trigger Macros

Event Trigger Name

CISCO_PHONE_EVENT

CISCO_SWITCH_EVENT

CISCO_ROUTER_EVENT

CISCO_WIRELESS_AP_EVENT

CISCO_WIRELESS_LIGHTWEIGHT_AP_EVENT

Description

System detects that a phone device is connected to an interface.

System detects that a switch is connected to an interface.

System detects that a router is connected to an interface.

System detects that a wireless application is connected to an interface.

System detects that a wireless lightweight application is connected to an interface.

OL-22170-01


17-3



Table 17-1 Auto SmartPorts Built-in Event Trigger Macros (continued)

Event Trigger Name

CISCO_DMP_EVENT

CISCO_IPVSC_EVENT

Description

System detects that a digital media player is connected to an interface.

System detects that an IP video surveillance camera is connected to an interface.

Table 17-2 shows the Auto SmartPorts built-in macros that are embedded in the switch software.

Auto SmartPorts Built-in Macros Table 17-2

Macro Name

CISCO_PHONE_AUTO_

SMARTPORT

CISCO_SWITCH_AUTO_

SMARTPORT

CISCO_ROUTER_AUTO_

SMARTPORT

CISCO_AP_AUTO_

SMARTPORT

CISCO_LWAP_AUTO_

SMARTPORT

Description

Use this macro for Cisco IP phone device. It enables QoS, port security,

Address Resolution Protocol (ARP) inspection (dynamic ARP inspection),

IP source guard, DHCP snooping, storm control and spanning tree protection on the port.

Use this macro to apply the switch macro for Cisco switches. It enables trunking on the port.

Use this macro to apply the router macro for Cisco routers. It enables QoS, trunking, and spanning tree protection on the port.

Use this macro to apply the wireless access point (AP) macro for Cisco

APs. It enables support for an autonomous wireless access point and QoS on the port.

Use this macro to apply the lightweight wireless access point macro for

Cisco lightweight wireless APs. It enables QoS, port security, dynamic

ARP inspection, IP source guard, DHCP snooping, storm control, and spanning tree protection on the port.

CISCO_IP_CAMERA_AUTO_SMARTPORT Use this macro for a Cisco IP surveillance camera device. It enables QoS, port security, and access VLAN on the port.

CISCO_DMP_AUTOSMARTPORT Use this macro for a Cisco digital media player device. It enables QoS, port security, and access VLAN on the port.

Note

By default, the built-in event triggers are mapped to the built-in macros.

Auto SmartPorts Configuration Guidelines

Auto SmartPort guidelines include the following:

•

•

To avoid system conflicts when Auto SmartPorts macros are applied, remove all port configuration except for 802.1X authentication.

If the macro conflicts with the original configuration, some macro commands might not be applied, or some antimacro commands might not be applied. (The antimacro is the portion of the applied macro that removes the macro at link down.)

17-4


OL-22170-01



Note

Failure of one command in the macro halts the application of the entire macro.

•

For example, if 802.1X authentication is enabled, you cannot remove switchport-mode access configuration. You must remove the 802.1X authentication before removing the configuration.

A port should not be a member of an EtherChannel when applying Auto SmartPorts macros.

If Auto SmartPort is not yet enabled globally, disable Auto SmartPort on all the EtherChannel ports before enabling it globally. If Auto SmartPort is already enabled, shut down the port and disable it before adding the port to an EtherChannel.

Note

If an Auto SmartPort macro is applied on an interface, EtherChannel configuration usually fails because of conflict with the auto-QoS configuration applied by the macro.

•

•

•

•

•

•

•

•

•

•

The built-in macro default data VLAN is VLAN 1. The default voice VLAN is VLAN 2. You should modify the built-in macro default values if your switch uses different VLANs. To view all built-in macro default values, use the show shell functions privileged EXEC command.

To detect non-Cisco devices for 802.1X authentication or MAB, configure the RADIUS server to support the Cisco AV pair auto-smart-port=event trigger. You must configure a user-defined trigger with the value returned in the AV pair for auto-smart-port.

For stationary devices that do not support CDP, MAB, or 802.1X authentication, such as network printers, we recommend that you disable Auto SmartPorts on the port.

If authentication is enabled on a port, the switch ignores CDP unless the fallback cdp keyword is in the macro auto global processing global configuration command.

The order of CLI commands within the macro and the corresponding antimacro can differ.

Before converting a port into an Layer 3 interface, enter the no macro auto processing command.

This prevents Auto SmartPort from applying macros on the interface. If Layer 3 is already configured, enter the no macro auto processing command on the Layer 3 interface enable Auto

SmartPort globally.

Auto SmartPort and SmartPorts cannot coexist on an interface.

A switch applies a macro in accordance with the LLDP advertisement from the attached device. If the device does not identify itself properly, the wrong macro is applied. Consult the specific device documentation to ensure the device's firmware is current.

The LWAP’s WLC software version must be 6.0.188 ( => Cisco IOS 12.4(21a)JA2) or later to make it detectable as LWAP by AutoSmartPort.

As of Cisco IOS Release 12.2(54)SG, Auto SmartPort does not support macros that apply

EtherChannel configurations. Interfaces that belong to EtherChannel groups are treated as standard interfaces. You can apply macros on individual interfaces based on the device type but the CLIs in the macro (for example, auto-QoS) might conflict with an EtherChannel configuration. We recommend that you disable Auto SmartPort on interfaces belonging to EtherChannels before you enable Auto SmartPort globally. If Auto SmartPort is already enabled, disable Auto SmartPort on the interfaces before configuring EtherChannel.

OL-22170-01


17-5



Configuring Auto SmartPorts Built-in Macro Parameters

The switch automatically maps from built-in event triggers to built-in macros. You can replace the built-in macro default values with values that are specific to your switch.

To configure Auto SmartPorts built-in macros parameters, perform this task:

Command

Step 1


Purpose


Step 2

Switch(config)# macro auto execute

event trigger builtin

built-in

macro name [parameter=value]

[parameter=value]

Defines mapping from an event trigger to a built-in macro.

Specify an event trigger value:

•

CISCO_PHONE_EVENT

•

•

•

CISCO_SWITCH_EVENT

CISCO_ROUTER_EVENT



•

•

•

•

CISCO_DMP_EVENT

CISCO_IPVSC_EVENT

•

WORD—Apply a user-defined event trigger.

Specify a built-in macro name value:

•

CISCO_PHONE_AUTO_SMARTPORT

(Optional) Specify the parameter values: $ACCESS_VLAN=(1) and

$VOICE_VLAN=(2).

CISCO_SWITCH_AUTO_SMARTPORT

(Optional) Specify the parameter values: $NATIVE_VLAN=(1).

Step 3


Step 4


Step 5


startup-config

•

•

•

CISCO_ROUTER_AUTO_SMARTPORT


CISCO_AP_AUTO_SMARTPORT


CISCO_LWAP_AUTO_SMARTPORT

(Optional) Specify the parameter values: $ACCESS_VLAN=(1).

CISCO_DMP_AUTO_SMARTPORT

•

•

CISCO_IP_CAMERA_AUTO_SMARTPORT

(Optional) parameter=value—Replace default values that begin with $.

Enter new values in the form of name value pair separated by a space:

[name1=value1 name2=value2...]. Default values are shown in parenthesis.


Verifies your entries.


17-6


OL-22170-01



The no macro auto execute event trigger {[builtin built-in macro name [parameter=value]] |

[[parameter=value] {function contents}]} command deletes the mapping.

This example shows how to use two built-in Auto SmartPorts macros for connecting Cisco switches and

Cisco IP phones to the switch. This example modifies the default voice VLAN, access VLAN, and native

VLAN for the trunk interface:


Switch(config)# macro auto execute CISCO_PHONE_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT

ACCESS_VLAN=10 VOICE_VLAN=20

Switch(config)#

Switch(config)#

Switch(config)#!!! the next command enables auto smart ports globally

Switch(config)# macro auto global processing fallback cdp

Switch(config)#

Switch(config)# exit

Switch#

Switch# show running-config interface gigabitethernet2/7

Building configuration...

Current configuration : 284 bytes

!

switchport access vlan 10 switchport mode access switchport voice vlan 2 switchport port-security maximum 2 switchport port-security switchport port-security aging time 2 switchport port-security violation restrict switchport port-security aging type inactivity auto qos voip cisco-phone qos trust device cisco-phone neighbor device type phone macro description CISCO_PHONE_EVENT spanning-tree portfast spanning-tree bpduguard enable service-policy input AutoQos-VoIP-Input-Cos-Policy service-policy output AutoQos-VoIP-Output-Policy end

Note

You can also use the macro auto device command to simplify changing the parameters for a built-in functions for a device type.

Configuring User-Defined Event Triggers

You can configure two types of event triggers: user-defined and MAC address-based.

The following sections describe these triggers:

•

802.1X-Based Event Trigger, page 17-7

•

MAC Address-Based Event Trigger, page 17-8

802.1X-Based Event Trigger

When using MAB or 802.1X authentication to trigger Auto SmartPorts macros, you need to create an event trigger that corresponds to the Cisco AV pair (auto-smart-port=event trigger) sent by the

RADIUS server.


OL-22170-01 17-7



To configure an event trigger, perform this task:

Command

Step 1


Step 2

Switch(config)# shell trigger

identifier description

Step 3


Step 4

Switch# show shell triggers

Step 5


startup-config

Purpose


Specifies the event trigger identifier and description.

The identifier should have no spaces or hyphens between words.


Displays the event triggers on the switch.


Use the no shell trigger identifier global configuration command to delete the event trigger.

The following example shows how to define a user-defined trigger:


Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# shell trigger RADIUS_MAB_EVENT MAC_AuthBypass Event

Switch(config)#

MAC Address-Based Event Trigger

To configure a MAC address group as an event trigger, perform this task:

Command

Step 1


Step 2

Switch(config)# macro auto

mac-address

group

Step 3


Step 4


Step 5


startup-config

Purpose


Specifies a group of MAC address as an event trigger.

Changes mode to config-mac-addr-grp. You can then add or remove the

MAC address or Organizational Unique Identifier (OUI) from the group.

The group value defines the user-defined trigger.




Use the no macro auto mac-address-group grp_name to delete the event trigger.

17-8


OL-22170-01



Configuring Mapping Between User-Defined Triggers and Built-in Macros

You need to map the user-defined trigger to either a built-in macro or user-defined macro.

To map a user-defined trigger to a built-in macros, perform this task:

Command

Step 1


Step 2

Switch(config)# macro auto execute

event trigger

builtin

built-in macro

name [parameter=value]

[parameter=value]

Step 3


Step 4


Step 5


startup-config

Purpose


Specifies a user-defined event trigger and a macro name. This action replaces built-in macro default values, and configures mapping from an event trigger to a built-in Auto Smartports macro.

Note

When performing a mapping, you must provide parameter values. For example, you must specify $ACCESS_VLAN=(1) and $VOICE_VLAN=(2) for the macro

CISCO_PHONE_AUTO_SMARTPORT.




This example shows how to map a user-defined event trigger called RADIUS_MAB_EVENT to the built-in macro CISCO_PHONE_AUTO_SMARTPORT with access VLAN set to 10, and how to verify the entries.

This procedure shows how to map a user-defined trigger to a built-in macro:

Step 1

Step 2

Step 3

Connect the device to a MAB-enabled switch port.

On the RADIUS server, set the attribute-value pair to auto-smart-port=RADIUS_MAB_EVENT.

On the switch, create the event trigger RADIUS_MAB_EVENT.

The switch recognizes the attribute-value pair=RADIUS_MAB_EVENT response from the RADIUS server and applies the macro CISCO_PHONE_AUTO_SMARTPORT, as in the following example:

Switch(config)# macro auto execute RADIUS_MAB_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT

ACCESS_VLAN=10

Switch(config)# exit


User defined triggers

---------------------

Trigger Id: RADIUS_MAB_EVENT

Trigger description: MAC_AuthBypass Event

Trigger environment:

Trigger mapping function: CISCO_PHONE_AUTO_SMARTPORT

<output truncated>

Configuring Auto SmartPorts User-Defined Macros

The Cisco IOS shell provides basic scripting capabilities for configuring the user-defined

Auto SmartPorts macros. These macros can contain multiple lines and can include any CLI command.

You can also define variable substitution, conditionals, functions, and triggers within the macro.


OL-22170-01 17-9



Inside a user-defined macro, besides parameters specified through macro auto execute trigger

parameter-name=value .., you also can use the following variables published by EEM ( Table 17-3 ).

Table 17-3 Variables Published by EEM

Parameter Name

$INTERFACE

$LINKUP

$TRIGGER

Meaning

Name of the interface where the trigger event is detected.

Indicates whether the interface is up or down (true/false).

Name of the trigger event that is raised (for example,

CISCO_PHONE_EVENT).

$AUTH_ENABLED Indicates whether 802.1X authentication is configured on the interface

(true/false).

To map an event trigger to a user-defined macro, perform this task:

Command

Step 1


Step 2

Switch(config)# macro auto

execute

event trigger

[parameter=value] {function

contents}

Step 3


Step 4


Step 5


startup-config

Purpose


Specifies a user-defined macro that maps to an event trigger.

•

•

•

Specify an event trigger value:

•

CISCO_PHONE_EVENT

CISCO_SWITCH_EVENT

CISCO_ROUTER_EVENT

•

•

•



WORD Applies a user-defined event trigger.

CISCO_DMP_EVENT

•

CISCO_IPVSC_EVENT

function contents—Specifies a user-defined macro to associate with the trigger. Enter the macro contents within braces. Begin the Cisco IOS shell commands with the left brace and end the command grouping with the right brace.

(Optional) parameter=value—Replaces default values that begin with $, enter new values in the form of name value pair separated by a space:

[name1=value1 name2=value2...].


Verifies your entries.


17-10


OL-22170-01



This example shows how to map a user-defined event trigger called Cisco digital media player (DMP) to a user-defined macro.

Step 1

Step 2

Step 3

Connect the DMP to an 802.1X- or MAB-enabled switch port.

On the RADIUS server, set the attribute-value pair to auto-smart-port

=MY_MEDIAPLAYER_EVENT.

On the switch, create the event trigger CISCO_DMP_EVENT, and map it to the user-defined macro commands shown below.

The switch recognizes the attribute-value pair=CISCO_DMP_EVENT response from the RADIUS server and applies the macro associated with this event trigger.

The following example shows the macro portion of the automacro:

Switch(config)# shell trigger CISCO_DMP_EVENT Cisco DMP player

Switch(config)# macro auto execute CISCO_DMP_EVENT {

if [[ $LINKUP -eq YES ]]; then conf t

interface $INTERFACE

macro description $TRIGGER

switchport access vlan 1

switchport mode access

switchport port-security

switchport port-security maximum 1

switchport port-security violation restrict

switchport port-security aging time 2

switchport port-security aging type inactivity

spanning-tree portfast

spanning-tree bpduguard enable

exit fi

The following represents the anti-macro portion of the automacro:

if [[ $LINKUP -eq NO ]]; then conf t interface $INTERFACE

no macro description $TRIGGER

no switchport access vlan 1

if [[ $AUTH_ENABLED -eq NO ]]; then

no switchport mode access

fi

no switchport port-security

no switchport port-security maximum 1

no switchport port-security violation restrict

no switchport port-security aging time 2

no switchport port-security aging type inactivity

no spanning-tree portfast

no spanning-tree bpduguard enable

exit fi

}


OL-22170-01


17-11



Table 17-4 lists the supported shell keywords your can apply in your macros and antimacro statements.

Table 17-4 Supported Cisco IOS Shell Keywords

}

[[

Command

{

]] else

-eq fi if then

-z

$

#

Description

Begin the command grouping.

End the command grouping.

Use as a conditional construct.








Variables that begin with the $ character are replaced with a parameter value.

Use the # character to enter comment text.

Table 17-5 lists the shell keywords that are not supported in macros and antimacros.

Table 17-5 Unsupported Cisco IOS Shell Reserved Keywords

Command

| case esac for function in select time until while

Description

Pipeline.

Conditional construct.


Looping construct.

Shell function.



Pipeline.

Looping construct.

Looping construct.

17-12


OL-22170-01


Displaying Auto SmartPorts


To display the Auto SmartPorts and static SmartPorts macros, use one or more of the privileged EXEC commands in

Table 17-6 .

Table 17-6 Commands for Displaying Auto SmartPorts and Static SmartPorts Macros

Command show parser macro show parser macro name

macro-name

show parser macro brief show parser macro description

[

interface

interface-id

]

show shell

[triggers | functions]

Purpose

Displays all static SmartPorts macros.

Displays a specific static SmartPorts macro.

Displays the static SmartPorts macro names.

Displays the static SmartPorts macro description for all interfaces or for a specified interface.

Displays information about Auto SmartPorts event triggers and macros.

This example shows how to use the show shell triggers privileged EXEC command to view the event triggers in the switch software:


User defined triggers

---------------------

Built-in triggers

-----------------

Trigger Id: CISCO_PHONE_EVENT

Trigger description: Event for ip-phone macro

Trigger environment: ACCESS_VLAN=1 VOICE_VLAN=2

Trigger mapping function: CISCO_PHONE_AUTO_SMARTPORT

Trigger Id: CISCO_ROUTER_EVENT

Trigger description: Event for router macro

Trigger environment: NATIVE_VLAN=1

Trigger mapping function: CISCO_ROUTER_AUTO_SMARTPORT

Trigger Id: CISCO_SWITCH_EVENT

Trigger description: Event for switch macro


Trigger mapping function: CISCO_SWITCH_AUTO_SMARTPORT

Trigger Id: CISCO_WIRELESS_AP_EVENT

Trigger description: Event for Wireless Access Point macro


Trigger mapping function: CISCO_AP_AUTO_SMARTPORT

Trigger Id: CISCO_WIRELESS_LIGHTWEIGHT_AP_EVENT

Trigger description: Event for Wireless Lightweight Access Point macro


Trigger mapping function: CISCO_LWAP_AUTO_SMARTPORT

This example shows how to use the show shell functions privileged EXEC command to view the built-in macros in the switch software:

Switch# show shell functions

#User defined functions:

#Built-in functions:

OL-22170-01


17-13



function CISCO_AP_AUTO_SMARTPORT () {

if [[ $LINKUP -eq YES ]]; then

conf t

interface $INTERFACE

macro description $TRIGGER

switchport trunk encapsulation dot1q

switchport trunk native vlan $NATIVE_VLAN

switchport trunk allowed vlan ALL

switchport mode trunk

switchport nonegotiate

auto qos voip trust

mls qos trust cos

exit

end

fi

if [[ $LINKUP -eq NO ]]; then

conf t


no macro description

no switchport nonegotiate

no switchport trunk native vlan $NATIVE_VLAN

no switchport trunk allowed vlan ALL

no auto qos voip trust

no mls qos trust cos

if [[ $AUTH_ENABLED -eq NO ]]; then

no switchport mode

no switchport trunk encapsulation

fi

exit

end

fi

} function CISCO_SWITCH_AUTO_SMARTPORT () {

if [[ $LINKUP -eq YES ]]; then

conf t


macro description $TRIGGER

auto qos voip trust

switchport trunk encapsulation dot1q

switchport trunk native vlan $NATIVE_VLAN

switchport trunk allowed vlan ALL

switchport mode trunk

exit

end

else

conf t


no macro description

no auto qos voip trust

no switchport mode trunk

no switchport trunk encapsulation dot1q

no switchport trunk native vlan $NATIVE_VLAN

no switchport trunk allowed vlan ALL

exit

end

fi

}

<output truncated>

17-14


OL-22170-01

Auto SmartPort Macro

Configuring Auto SmartPort Macros

About Auto SmartPorts

Configuring Auto SmartPorts

Enabling Auto SmartPorts

Auto SmartPorts Default Configuration

Auto SmartPorts Configuration Guidelines

Configuring Auto SmartPorts Built-in Macro Parameters

Configuring User-Defined Event Triggers

802.1X-Based Event Trigger

MAC Address-Based Event Trigger

Configuring Mapping Between User-Defined Triggers and Built-in Macros

Configuring Auto SmartPorts User-Defined Macros

Displaying Auto SmartPorts

Related manuals

Cisco

Catalyst 3560-X Series Switches

Cisco

Catalyst 3560-X Series Switches

Cisco

Catalyst 3650 Series Switches

Cisco

Catalyst 3750-X Series Switches

Cisco

Catalyst 3750 Series Switches

Cisco

Catalyst 3560-X Series Switches