USER MANUAL - Stoltronic

USER MANUAL - Stoltronic
USER MANUAL
TG2480H
CUSTOM S.p.A.
Via Berettine 2/B
43010 Fontevivo (PARMA) - Italy
Tel. : +39 0521-680111
Fax : +39 0521-610701
http: www.custom.biz
Customer Service Department:
Email : [email protected]
© 2014 CUSTOM S.p.A. – Italy.
All rights reserved. Total or partial reproduction of this manual in whatever form,
whether by printed or electronic means,
is forbidden. While guaranteeing that the
information contained in it has been carefully checked, CUSTOM S.p.A. and other
entities utilized in the realization of this
manual bear no responsibility for how the
manual is used.
Information regarding any errors found in it
or suggestions on how it could be improved
are appreciated. Since products are subject to continuous check and improvement,
CUSTOM S.p.A. reserves the right to make
changes in information contained in this
manual without prior notii cation.
The pre-installed multimedia contents
are protected from Copyright CUSTOM
S.p.A. Other company and product names
mentioned herein may be trademarks of
their respective companies. Mention of
third-party products is for informational
purposes only and constitutes neither
an endorsement nor a recommendation.
CUSTOM S.p.A. assumes no responsibility
with regard to the performance or use of
these products.
THE IMAGES USED IN THIS MANUAL ARE USED AS AN ILLUSTRATIVE EXAMPLES. THEY COULDN’T
GENERAL SAFETY INFORMATION
Your attention is drawn to the following
actions that could compromise the characteristics of the product:
• Read and retain the instructions which
follow.
• Follow all indications and instructions
given on the device.
• Make sure that the surface on which
the device rests is stable. If it is not, the
device could fall, seriously damaging it.
• Make sure that the device rests on a hard
(non-padded) surface and that there is
sufi cient ventilation.
• When positioning the device, make sure
cables do not get damaged.
• Use the type of electrical power supply
indicated on the device label. If uncertain, contact your dealer.
• Make sure the electrical system that
supplies power to the device is equipped
with a ground wire and is protected by a
differential switch.
• Do not block the ventilation openings.
• Do not insert objects inside the device as
this could cause short-circuiting or damage components that could jeopardize
printer functioning.
• Do not carry out repairs on the device
yourself, except for the normal maintenance operations given in the user
manual.
• Make sure that there is an easily-accessible outlet with a capacity of no less
than 10A closely to where the device is
to be installed.
• Periodically perform scheduled maintenance on the device to avoid dirt build-up
that could compromise the correct, safe
operation of the unit.
• Before any type of work is done on the
machine, disconnect the power supply.
• Do not touch the head heating line with
bare hands or metal objects. Do not
perform any operation inside the printer
immediately after printing because the
head and motor tend to become very
hot.
REPRODUCE THE DESCRIBED
MODEL FAITHFULLY.
UNLESS OTHERWISE SPECIFIED,
THE INFORMATION GIVEN IN THIS
MANUAL
ARE REFERRED TO ALL MODELS
IN PRODUCTION AT THE ISSUE
DATE OF THIS DOCUMENT.
GENERAL INSTRUCTIONS
CUSTOM S.p.A. declines all responsibility for accidents or damage to persons or
property occurring as a result of tampering,
structural or functional modii cations, unsuitable or incorrect installations, environments not in keeping with the equipment’s
protection degree or with the required temperature and humidity conditions, failure
to carry out maintenance and periodical
inspections and poor repair work.
THE CE MARK AFFIXED TO
THE PRODUCT CERTIFY
THAT THE PRODUCT SATISFIES THE BASIC SAFETY
REQUIREMENTS.
The device is in conformity with the essential Electromagnetic Compatibility and
Electric Safety requirements laid down in
Directives 2006/95/CE and 2004/108/CE
inasmuch as it was designed in conformity
with the provisions laid down in the following Standards:
• EN 55022 Class B (Limits and methods
of measurements of radio disturbance
characteristics of Information Technology Equipment)
• EN 55024 (Information Technology
Equipment – Immunity characteristics –
Limits and methods of measurement)
• EN 60950-1 (Safety of information
equipment including electrical business
equipment)
GUIDELINES FOR
THE DISPOSAL OF
THE PRODUCT
The crossed-out rubbish bin logo means
that used electrical and electronic products
shall NOT be mixed with unsorted municipal waste. For more detailed information
about recycling of this product, refer to the
instructions of your country for the disposal
of these products.
• Do not dispose of this equipment as
miscellaneous solid municipal waste, but
arrange to have it collected separately.
• The re-use or correct recycling of the
electronic and electrical equipment
(EEE) is important in order to protect
the environment and the wellbeing of
humans.
• In accordance with European Directive
WEEE 2002/96/EC, special collection
points are available to which to deliver
waste electrical and electronic equipment and the equipment can also be
handed over to a distributor at the moment of purchasing a new equivalent
type.
• The public administration and producers
of electrical and electronic equipment
are involved in facilitating the processes
of the re-use and recovery of waste electrical and electronic equipment through
the organisation of collection activities
and the use of appropriate planning arrangements.
• Unauthorised disposal of waste electrical
and electronic equipment is punishable
by law with the appropriate penalties.
The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this
copy.
MANUAL
For details on the commands,
refer to the manual with code. 77200000001100
TABLE OF CONTENTS
1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1
1.2
Document structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Explanatory notes used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2
DESCRIPTION
2.1
2.2
2.3
2.4
2.5
2.6 Box content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Device components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Product label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Key functions: power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Key functions: standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Status led lashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 Paper roll holder assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Collections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.4 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.5 Driver and SDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
Device opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Device closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Adjusting paper width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adjusting paper stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Switch the device ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Loading the paper roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Anti-jamming system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Issuing ticket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5
CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.1 5.2
5.3
5.4
5.5
Coniguration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setup report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Printer status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Printer parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Hexadecimal dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7
6
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1
6.2
6.3
6.4 Paper jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Planning of cleaning operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Upgrade irmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7
SPECIFICATION
7.1 7.2 7.3
7.4
7.5 7.6
Hardware speciications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Character speciications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Device dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Power supply dimensions cod.963GE020000003 (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Paper speciication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Character sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
8
CONSUMABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
9 ACCESSORIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
9.1 Adapter cable for power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
10 ALIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
10.1 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
10.2 Alignment parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
10.3 Printing area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
11 TECHNICAL SERVICE
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
1
INTRODUCTION
1.1
Document structure
This document includes the following chapters:
1
INTRODUCTION
information about this document
2
DESCRIPTION
general description of device
3
INSTALLATION
information required for a correct installation of the device
4
OPERATION
information required to make the device operative
5 CONFIGURATION description of the coniguration parameters of the device
6
information for a correct periodic maintenance
MAINTENANCE
7 SPECIFICATION technical speciication for the device and its accessories
8
CONSUMABLES
description and installation of the available consumables for the device
9
ACCESSORIES
description and installation of the available accessories for the device
10 ALIGNMENT
information required for managing the paper alignment
11 TECHNICAL SERVICE
information required for contacting the technical service
1.2
Explanatory notes used in this manual
NOTE:
Gives important information or suggestions relative to the use of the device
ATTENTION:
Gives information that must be carefully followed to guard against damaging the
device
DANGER:
Gives information that must be carefully followed to guard against operator injury or
damage
9
10
2
DESCRIPTION
2.1
Box content
Remove the device from its carton being careful not to damage the packing material so that it may be re-used if the printer
is to be transported in the future.
Make sure that all the components illustrated below are present and that there are no signs of damage. If there are, contact
Customer Service
1. Power supply cable
1
2. Fixing screws for paper roll holder
3. Paper roll
2
4. Installation instruction sheet
5. Device (all models)
6. Paper roll holder
3
4
5
6
• Open the device packaging.
• Take out the device.
• Take out the rest of the content.
• Keep the box, trays and packing materials in the event the printer must be transported/shipped in the future.
11
2.2
Device components
Standard model
1. Paper width adjustment
13. USB port
2. Paper roll holder pin
14. Status led
3. Near paper end sensor
15. Power supply port
4. Lever for paper stock adjustment
16. Serial port
5. Paper roll holder
17. Paper in
6. Printing head
18. Paper in presence and black mark sensor
7. Cutter group
19. Rear cover
8. Ticket withdrawal sensor
20. Paper jam sensor
9. Inspection door
21. FEED key
10. Paper out
22. PRINT key
11. Unlocking hook for cutter group
23. Unlocking lever for rubber roller
12. Device chassis
24. Rubber roller manual feed
1
20
21
22
23
2
3
4
5
6
7
8
9
24
10
11
12
13
14
15
16
19
12
18
17
Model with motorized ejector
1. Paper width adjustment
13. Status led
2. Paper roll holder pin
14. Power supply port
3. Near paper end sensor
15. Serial port
4. Lever for paper stock adjustment
16. FEED key
5. Printing head
17. PRINT key
6. Cutter group
18. Paper roll holder
7. Ejector group
19. Paper in
8. Paper out
20. Paper in presence and black mark sensor
9. Paper out presence sensor
21. Rear cover
10. Unlocking hook for cutter group
22. Unlocking lever for rubber roller
11. Device chassis
23. Rubber roller manual feed
12. USB port
1
18
19
20
21
22
2
3
4
5
6
7
23
8
9
10
11
12
13
14
15
16
17
13
2.3
Product label
PC = Product code (14 digits)
SN = Serial number
HW = Hardware release
XXXXXXXXXXXXXX
Rx
0000000000000000000
PC
14
SN
HW
2.4
Key functions: power up
The following igure shows the functions of device’s keys according to the operating condition.
POWER UP
PRINT FEED
PRINT FEED
Hold
down
Hold
down
printing
FONT TEST
printing
SETUP report
PRINT FEED
PRINT FEED
Hold
down
Fast
push
skip the
SETUP mode
enter the SETUP MODE
PRINT FEED
Hold
down
next
parameter
PRINT FEED
Fast
push
modify
parameter
15
2.5
Key functions: standby
The following igure shows the functions of device’s keys according to the operating condition.
STANDBY
PRINT FEED
Fast
push
Printing
demo ticket
16
PRINT FEED
Fast
push
Advance the paper
(preset length)
2.6 Status led lashes
The Status led indicates hardware status of device. Given in the table below are the various led signals and the corresponding device status.
STATUS LED
DESCRIPTION
-
OFF
DEVICE OFF
GREEN
ON
DEVICE ON: NO ERROR
x1
RECEIVE DATA
x2
HEADING OVER TEMPERATURE
x3
PAPER END
x4
POWER SUPPLY VOLTAGE INCORRECT
x5
RECEPTION ERROR
(PARITY, FRAME ERROR, OVERRUN ERROR)
x6
COMMAND NOT RECOGNIZED
x7
COMMAND RECEPTION TIME OUT
x8
INSPECTION DOOR OPEN (1)
x9
PAPER JAM (1)
x 10
NEAR PAPER END
x 11
CUTTER ERROR
GREEN
COMMUNICATION
STATUS
GREEN
UNRECOVERABLE
ERROR
NOTE:
(1) : Only for standard models.
17
18
3
INSTALLATION
3.1
Fastening
Standard model
The device is provided with three ixing holes on the bottom of device (see following igure). To fasten the device on a panel, use three M3 screws.
126.2
113.2
56.6
38.7
80.8
6
61.4
Ø
27
6.
3.1
NOTE: All the dimensions shown in igure are in millimetres.
19
Model with motorized ejector
The device is provided with three ixing holes on the bottom of device (see following igure). To fasten the device on a panel, use three M3 screws.
126.2
113.2
56.6
Ø
27
6.
6
6
3.1
42.1
6
35.5
16.2
NOTE: All the dimensions shown in igure are in millimetres.
20
3.2
Paper roll holder assembly
The paper roll holder position is adjustable on four different positions: upper position P1, rotated upward P2, rear P3,
rotated downward P4.
Fix the paper roll holder to the device holes shown in igure according to the desired position by using the two M4x6 ixing screws supplied.
P1
P2
21
P3
P4
ATTENTION: While assembly the paper roll holder check the cable path (near paper end sensor) is correct. Incorrect
positions of the cable could cause damage on it.
22
3.3
Collections
The following igure shows the possible connections for the device.
COM
24Vdc
Power supply cable
(supplied)
PC
serial device
Power supply
PC
USB device
ATTENTION: In some using conditions, we recommend the installation of a ferrite core on the power supply cable.
NOTE: If RS232 and USB connectors are inserted, communication port is USB.
23
3.4
Pinout
2
POWER SUPPLY
Male Molex connector series 5569 vertical (n° 39-30-1020)
1
1 +24 Vdc
J14
2 GND
ATTENTION:
Respect power supply polarity.
NOTE: Power supply cable
The following igure shows the connector pinout of the power supply cable for the device:
Female Molex connector
series 5557 (n.39-01-3022)
Power supply cable
1
2
2
1
USB INTERFACE
Female USB type B connector
3
J1
4
1 USB-ON
(in)
2 D0 -
(in/out)
3 D0 +
(in/out)
4 GND
SH1 SHIELD
SH2 SHIELD
24
PIN
Signal
1
Cable
color
Red
2
Black
GND
+24V
SERIAL INTERFACE
Female RJ45 connector
8
1
1 n.c.
2 GND
J15
3 TX
(out)
During transmission, takes the value “0” and “1”, depending on data
4 RX
(in)
During reception, takes the value “0” and “1”, depending on data
5 RTS
(out)
When “1”, printer is ready to receive data
6 n.c.
7 n.c.
8 n.c.
1
2
3
4
5
6
7
8
DEVICE
GND
RXD
TXD
TXD
RXD
RTS
GND
RTS
1
2
3
4
5
6
7
8
9
DB9
RJ45
NOTES
DEVICE > PC connection
The following picture shows an example of connection between the device and a personal computer using an 8 pin serial
RJ45 male connector and a 9 pin female connector.
PC
When use a serial cable, we recommend the installation of a ferrite core on the power supply cable.
Given the presence of the RS232 standard, logic value “0” corresponds to a voltage level of between +3 Vdc and +15
Vdc and logic value “1” corresponds to a voltage level of between -3 Vdc and -15 Vdc.
25
3.5
Driver and SDK
The drivers are available for the following operating system:
OPERATING
SYSTEM
DESCRIPTION
INSTALLATION PROCEDURE
Driver for Windows XP
Driver for Windows VISTA (32/64bit)
Windows
Driver for Windows 7 (32/64bit)
From the START menu, press Run
and type-in the path where the SW
was saved on your PC, then click OK.
Follow the instructions that appear
on the screen to install the driver.
Driver for Windows 8 (32/64bit)
Opos
Follow the instruction get back on the
README.TXT ile. You can ind it in the
software package downloaded in advance.
Linux
Android
Library for CustomAndroidAPI
NOTE:
All drivers can be found in the DOWNLOAD section of the web site www.custom.biz.
26
Extract the zipped folder to
the destination path desired.
Follow the instructions present
in the software package that you
downloaded on how to install
and use the library.
4
OPERATION
4.1
Device opening
1
Lift the ejector group by unhooking the magnets on the bottom side
and by rotating the group upwards.
2
Widen the unlocking hook for the cutter group.
27
3
Rotate upwards the cutter group to lift it.
4.2
Device closing
1
Check the presence of paper scraps
and remove them (see par.6.3).
28
2
Widen the unlocking hook
and close the cutter group.
3
Lower the ejector group and hook
the two magnets to the device chassis.
29
4.3
Adjusting paper width
The device allows the use of paper roll width from 52mm to 80mm. To adjust the width of the paper roll case, rotate the
knob as shown in the following igure.
NOTE:
Properly set the value of the “Paper Width” parameter during the Setup procedure (see chapter 5).
30
4.4
Adjusting paper stock
The device allows the move the position of the near paper end sensor to adjust the amount of paper on the roll under
which report the near paper end.
Use the lever shown in igure to move the near paper end sensor: move the lever up to increase the paper stock, move the lever down to decrease the paper stock.
+
-
31
4.5
Switch the device ON
1
IN DC 24V
COM
2.2A
24Vdc
Power supply cable
EXTERNAL
POWER SUPPLY
(OPTIONAL)
Connect the power supply cable to an external power supply unit and to the device.
Use the type of electrical power supply indicated on the label.
2
COM
The green status led turn on
and the device is ready.
32
24Vdc
4.6
Loading the paper roll
To change the paper proceed as follows.
1
+
Adjust the paper stock
(see previous paragraphs).
2
Inser the paper roll on the pin
of the roll holder.
3
Adjust the paper width
(see previous paragraphs).
33
4
COM
24Vdc
Cavo di alimentazione
Accendere il dispositivo
(vedere paragrafi precedenti).
5
Inserire la carta nella bocca di ingresso
rispettando il verso di rotazione mostrato in figura.
5
VROOM
Attendere il caricamento automatico della carta.
NOTE: At every change of paper roll, check inside the device and remove any scraps of paper and accumulated dust
(see par.6.2).
34
4.7
Anti-jamming system
Standard model
The withdrawal of the ticket before the end of printing, may damage the printing mechanism or the paper ripping resulting
in probable jam.
The device is equipped with an anti-jamming system that starts operating when the user tries to pick up the ticket while
printing is still in progress.
This system is composed of an oscillating plane placed under the inspection door and of a fork sensor that detects the
movements of the oscillating plane.
The user that make a ticket withdrawal before the printing end, causes the tension of the paper resulting in the lowering of
the oscillating plane. This movement engages the fork sensor: printing is interrupted and the ticket is cut instantly.
Inspection door
Oscillating plane
Fork sensor
35
4.8
Issuing ticket
The device allows you to choose between different operating modes for the issuance of printed tickets.
The operating modes shown in the following images, depend on the settings of the coniguration parameters and commands sent to the device.
“EJECT” mode (standard model)
1
Paper input
Printing head
The device starts the ticket printing.
2
Printing head
The device continues the ticket printing while
the portion already printed starts to get out of the cutter.
36
Paper output
3
Cutter
Paper output
Ticket presented
When printing ends, the device cuts the ticket printed
and presents a portion of it on the paper mouth
4
Paper output Ticket withdrew
The user withdraw the ticket from the paper mouth.
37
“EJECT” mode (model with motorized ejector)
1
Paper input
Printing head
The device starts the ticket printing.
2
Printing head
Ejector rollers
Ejector sensor
The ticket advances ahead to engage the ejector sensor and is caught between the ejector rollers. The printed portion
of ticket is collected in the space between cutter and ejector while the device continues printing.
38
3
Cutter
Ejector rollers
When printing ends, the device cuts the ticket printed.
4
Ejector rollers
Paper output
Ticket ejected
The device directly ejects the ticket
39
“PRESENT-EJECT” mode (model with motorized ejector)
1
Paper input
Printing head
The device starts the ticket printing.
2
Printing head
Ejector rollers
Ejector sensor
The ticket advances ahead to engage the ejector sensor and is caught between the ejector rollers. The printed portion
of ticket is collected in the space between cutter and ejector while the device continues printing.
40
3
Cutter
Ejector rollers
When printing ends, the device cuts the ticket printed.
4
Ejector rollers
Paper output
Ticket presented
The device presents a portion of the ticket printed on the paper mouth.
41
5
The ticket is waiting on the paper mouth for a preset period of time
6
Ejector rollers
The device directly ejects the ticket
42
Paper output
Ticket ejected
“PRESENT” mode (model with motorized ejector)
1
Paper input
Printing head
The device starts the ticket printing.
2
Printing head
Ejector rollers
Ejector sensor
The ticket advances ahead to engage the ejector sensor and is caught between the ejector rollers. The printed portion
of ticket is collected in the space between cutter and ejector while the device continues printing.
43
3
Cutter
Ejector rollers
When printing ends, the device cuts the ticket printed.
4
Ejector rollers
Paper output
The device presents a portion of the ticket printed on the paper mouth.
44
Ticket presented
5
Ejector rollers
Paper output
Ticket withdrew
The user withdraw the ticket from the paper mouth
NOTE:
For further information, refer to chapter 5 and to the Commands Manual.
45
46
5
CONFIGURATION
5.1 Coniguration mode
To enter the coniguration mode and print a setup report with the operating parameters of the device, proceed as follows.
1
PRINT FEED
COM
24Vdc
While pressing the FEED key,
switch on the device by inserting the power supply cable.
2
TG2480H printer
-
rel 1.00
PRINTER SETUP
PRINTER TYPE
BOOT LOADER
BCODE
SCODE
HEAD VOLTAGE [V]
HEAD TEMP. [°C]
CUT COUNTER
POWERON COUNTER
PAPER PRINT [cm]
PWM NOTCH AVG.
PWM NOTCH WHITE
PWM NOTCH BLACK
= TG2480H
= rel.1.00
= <code>
= <code>
= 23.57
= 24
= 0
= 100
= 160
= 50%
= 0%
= 100%
Printer Emul...............................:
Baud Rate .................................:
Data Length ...............................:
Parity .........................................:
Handshaking .............................:
Busy Condition ..........................:
ESCPOS
19200 bps
8 bits/chr
None
XON/XOFF
RxFull
The device prints the report with
parameters for settings.
3
PRINT FEED
Enter
setup
Hold down the FEED key to enter
the configuration mode.
47
5.2
Setup report
The following igure shows the setup report of the device. The shown values for parameters are sample values; for the list and the description of device parameters see the following paragraphs.
PRINTER NAME and
FIRMWARE RELEASE
TG2480H printer
-
rel 1.00
PRINTER SETUP
DEVICE
STATUS
DEVICE
PARAMETERS
KEYS FUNCTIONS
48
PRINTER TYPE
BOOT LOADER
BCODE
SCODE
HEAD VOLTAGE [V]
HEAD TEMP. [°C]
CUT COUNTER
POWERON COUNTER
PAPER PRINT [cm]
PWM NOTCH AVG.
PWM NOTCH WHITE
PWM NOTCH BLACK
= TG2480H
= rel.1.00
= <code>
= <code>
= 23.57
= 24
= 0
= 100
= 160
= 50%
= 0%
= 100%
Baud Rate .................................:
Data Length ...............................:
Parity .........................................:
Handshaking .............................:
Busy Condition ..........................:
Autofeed ....................................:
USB Address N .........................:
Print Mode .................................:
Code Table ................................:
Chars / inch ...............................:
Speed / Quality..........................:
Print Width .................................:
Notch Align. ...............................:
Notch ThresH ............................:
Notch Dist.mm. ..........................:
Print Density..............................:
[Feed PUSH]
[Feed FAST PUSH]
19200 bps
8 bits/chr
None
XON/XOFF
RxFull
CR Disabled
0
Normal
PC437
A=11 B=15 cpi
Normal
56 mm
Enabled Internal
1.25V
00.0
0%
enter setup
skip setup
5.3
Printer status
The printer operating status is indicated in the coniguration print-out in which, next to the name of the components displayed, the following information is given:
PRINTER TYPE
device model
BOOT LOADER
boot loader release
BCODE
release of the BCODE irmware module
SCODE
release of the SCODE irmware module
HEAD VOLTAGE
voltage of the head
HEAD TEMP
temperature of the head
CUT COUNTER
number of cuts made
POWER ON COUNTER
number of power-ups made
PAPER PRINT
centimetres of paper printed
PWM NOTCH AVG.
for future use
PWM NOTCH WHITE
for future use
PWM NOTCH BLACK
for future use
49
5.4
Printer parameters
This printer allows the coniguration of the parameters listed in the following table.
The parameters marked with the symbol D are the default values.
Settings remain active even after the printer has been turned off and they are stored in non-volatile memory.
BAUD RATE
Communication speed of the serial interface:
115200 D
57600
38400
19200
9600
4800
2400
1200
NOTE: Parameter valid only with serial interface.
DATA LENGTH
Number of bit used for characters encoding:
7 bits/car
8 bits/car D
NOTE: Parameter valid only with serial interface.
PARITY
Bit for the parity control of the serial interface:
None D = parity bit omitted
Even = even value for parity bit
Odd =
odd value for parity bit
NOTE: Parameter valid only with serial interface.
HANDSHAKING
Handshaking:
XON/XOFF D = software handshaking
Hardware =
hardware handshaking (CTS/RTS)
NOTES:
Parameter valid only with serial interface.
When the receive buffer is full, if handshaking is set to XON/XOFF, the printer sends the XOFF (0x13) on the
serial port. When the receive buffer has cleared once again, if handshaking is set to XON/XOFF, the printer
sends the XON (0x11) on the serial port.
BUSY CONDITION
Activation mode for Busy signal:
OffLine/ RXFull = Busy signal is activated when the printer is both in OffLine status and
the buffer is full
RXFull D =
Busy signal is activated when the buffer is full
NOTE: Parameter valid only with serial interface.
AUTOFEED
Setting of the Carriage Return character:
CR disabled D = Carriage Return disabled
CR enabled = Carriage Return enabled
50
USB ADDRESS N
Numerical address code for the univocal identiication of the USB device (in case of more
than a USB device connected with the same PC):
0D
1
PRINT MODE
2
3
4
5
6
7
8
9
Printing mode:
Normal D = enables printing in normal writing way
Reverse = enables printing rotated 180 degrees
CODE TABLE [num]
Characters table (character code).
PC865
PC858
PC866
VISCII
PC437 D
U.D.P. (1)
PC850
PC860
PC863
NOTE:
This parameter is not printed in the setup report of models with simpliied chinese font GB2312. or with extended chinese font GB18030.
(1) : U.D.P. = User-deined page
CHARS / INCH
Font selection:
A = 11 cpi, B = 15 cpi D
A = 15 cpi, B = 20 cpi
NOTES: CPI = Characters Per Inch
SPEED / QUALITY
Setting of printing speed and printing quality:
Normal D
High Speed
PRINT WIDTH
Width of printing area:
52 mm
56 mm
60 mm
NOTCH ALIGNMENT
64 mm
68 mm
72 mm
76 mm D
80 mm
Management of the paper alignment:
the notch alignment is not performed
Disabled D =
Enabled Internal (1) = the notch alignment is performed
Enabled External (1) = the notch alignment is performed
NOTE:
(1) : The difference between the “Enabled Internal” and “Enabled External” values is reserved for future use:
both the values enable the notch alignment.
51
NOTCH THRESHOLD
Threshold value for the recognition of the presence of notch by the notch sensor:
0.75V
1.00V
1.25V D
1.50V
1.75V
2.00V
2.25V
2.75V
2.50V
NOTE: If the “Notch Alignment” parameter is disabled, the “Notch Threshold” parameter is not printed.
NOTCH DISTANCE
“Notch Distance” is the minimum distance (in mm) between the upper edge of ticket and
the notch.
The numeric value of the distance is made up with the following three parameters for the
setting of three digits (two for the integer part of the number and one for the decimal part):
Setting the digit for tens:
NOTCH DISTANCE [mm x 10]
0D
1
Setting the digit for units:
NOTCH DISTANCE [mm x 1] (1)
0D
1
2
3
4
5
6
7
8
9
Setting the digit for decimals:
NOTCH DISTANCE [mm x .1]
0D
1
2
3
4
5
6
7
8
9
NOTES:
For example, to set the notch distance to 10 mm, modify the parameters as follows:
Notch Distance [mm x 10] = 1
Notch Distance [mm x 1] = 0
Notch Distance [mm x .1] = 0
If the “Notch Alignment” parameter is disabled, the “Notch Distance” parameter is not printed
(1) : The values of “Notch Distance [mm x 1]” > 2 can be set only if “Notch Distance [mm x 10]” = 0.
PRINT DENSITY
Adjusting the printing density:
-50%
-37%
-25%
52
-12%
0D
+12%
+25%
+37%
+50%
5.5
Hexadecimal dump
This function is used for the diagnosis of the characters received from the communications port. Characters are printed as
hexadecimal code and the corresponding ASCII code (see below). Each line is preceded by a counter in hexadecimal that
indicates the number of bytes received.
During the startup, if you hold down the FEED key, the printer enters the self-test routine and print the setup report.
The printer remains in standby until a key is pressed or characters are received through the communication port (Hexadecimal Dump mode). For each character sent, the ticket shows the hexadecimal value and the ASCII codes (if the characters
are underlined, the receive buffer is full). Shown below is an example of a Hexadecimal Dump:
HEXADECIMAL DUMP
31
39
37
68
73
66
65
6F
6F
77
72
6B
64
73
66
6A
32
30
38
6B
64
73
69
72
75
65
69
6C
66
64
6B
6B
33
31
39
6A
66
64
6F
69
77
72
6F
73
6B
66
F2
6C
34
32
75
73
6B
66
79
75
65
69
75
64
73
6B
6A
68
35
33
69
64
6A
6B
75
77
72
6F
77
66
64
6A
73
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
12345 ...
90123 ...
789ui ...
hkjsd ...
sdfkj ...
fsdfk ...
eioyu ...
oriuw ...
ouwer ...
werio ...
riouw ...
klsdf ...
dfksd ...
sdfkj ...
fk≥j ...
jklh
53
54
6
MAINTENANCE
6.1
Paper jam
Standard model
1
Lift the inspection door.
2
Remove any scraps of paper
from the front side of the device.
55
3
Open the device
(see previous paragraphs).
4
Lift the unlocking lever for the rubber roller
and remove any scraps of paper from the printing mechanism.
5
Rotate clockwise the rubber roller
to eject the paper from the rear side of the device.
56
Model with motorized ejector
1
Open the device
(see previous paragraphs).
2
Lift the unlocking lever for the rubber roller
and remove any scraps of paper from the printing mechanism.
3
Rotate clockwise the rubber roller
to eject the paper from the rear side of the device.
57
6.2
Planning of cleaning operations
The regular cleaning of the device keeps the print quality and extends its life. The following table shows the recommended
planning for the cleaning operations.
EVERY PAPER CHANGE
Rollers
Use isopropyl alcohol
EVERY 5 PAPER CHANGES
Paper path
Use compressed air or tweezers
Cutter
Use compressed air
Ejector
Use compressed air
Sensors
Use compressed air
EVERY 6 MONTHS OR AS NEEDED
Printer case
Use compressed air or a soft cloth
For speciic procedures, see the following pages.
NOTE:
If you use the device in dusty environments, you must reduce the intervals between the cleaning operations.
58
6.3
Cleaning
For periodic cleaning of the device, see the instructions below
Rollers
Paper path
1
1
Disconnect the power supply cable and
open the device (see previous paragraphs).
2
Disconnect the power supply cable and
open the device (see previous paragraphs).
2
ISOPROPYL ALCOHOL
Clean the printing roller by using
a non-abrasive cloth moistened with isopropyl.
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the device.
ON
Remove any scraps of paper and the
accumulated paper dust on the rubber roller and in
areas near to the paper presence sensor.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
Alcohol, solvent
ON
59
Cutter
Case
1
1
Disconnect the power supply cable and
open the device (see previous paragraphs).
2
Disconnect the power supply cable
(see previous paragraphs).
2
ISOPROPYL ALCOHOL
Remove any scraps of paper and the
accumulated paper dust on the input
and the output of cutter.
To clean the device,
use compressed air or a soft cloth
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
Alcohol, solvent
60
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
ON
Alcohol, solvent
ON
Ejector (standard model)
Ejector (model with motorized ejector)
1
1
Disconnect the power supply cable and
lift the inspection door (see previous paragraphs).
2
Disconnect the power supply cable and
lift the ejector group (see previous paragraphs).
2
Remove any scraps of paper and the
accumulated paper dust under the inspection door
and on the paper output.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
Alcohol, solvent
Remove any scraps of paper and the
accumulated paper dust on the input
and the output of the ejector.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
ON
Alcohol, solvent
ON
61
Sensors (standard model)
1
3
Disconnect the power supply cable and open
the inspection door (see previous paragraphs).
2
Clean the near paper end sensor
by using compressed air.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
Alcohol, solvent
Clean the anti-jamming sensor
by using compressed air.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the device.
Alcohol, solvent
62
ON
ON
6.4 Upgrade irmware
9. Select the serial communication port (ex. COM1):
WARNING: During communication between PC and
device for the irmware update it is strictly forbidden to disconnect the communication cable or to remove the
power supply of the devices not to endanger the proper
functioning of the machine.
NOTES:
The latest irmware of the device is available in the download area of the web site www.custom.biz
Install on the PC used for printer upgrading the UPGCEPRN software available in the download area of the
web site www.custom.biz.
C:\TG2480H.PSW
Update via serial interface
Proceed as follows:
1. Write down the product code (14 digits) printed on the
product label (see par.2.3).
2. Go to the web site www.custom.biz and download the
appropriate irmware release from the DOWNLOAD area.
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
5. Connect the device to the PC using a serial cable (see
par.3.3).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
8. Select the update ile .PSW location:
10. Detecting and setting of the parameters necessary for
serial communication are performed automatically and
then updating begins.
11. After a few minutes a message on the screen warns
that the update is completed.
12. Print a new SETUP report to verify the new irmware release (see chapter 5).
63
Update via USB interface
ATTENTION:
Only during the irmware update, the connection between PC and device must be direct, without the use of HUB
device.
9. Select item USB and then select the USB device among
those proposed (e.g. TG2480H):
Custom TG2480H
Only during the irmware update, do not connect or disconnect other USB devices.
NOTE: For communication via USB you must install on
PC the printer driver available in the download area of
the web site www.custom.biz.
C:\TG2480H.PSW
Proceed as follows:
1. Write down the product code (14 digits) printed on the
product label (see par.2.3).
2. Go to the web site www.custom.biz and download the
appropriate irmware release from the DOWNLOAD area.
C:\TG2480H.PSW
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
5. Connect the device to the PC using a USB cable (see
par.3.3).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
8. Select the update ile .PSW location:
10. After a few minutes a message on the screen warns
that the update is completed.
11. Print a new SETUP report to verify the new irmware release (see chapter 5).
64
7
SPECIFICATION
7.1 Hardware speciications
GENERAL
Sensors
standard model
model with motorized ejector
MTBF (1)
Noise level (standard model)
Emulations
Printing driver
Paper presence in input, head temperature, paper jam,
ticket withdrawal, external near paper end (on paper roll holder)
Paper presence in input, paper presence in output,
head temperature, external near paper end (on paper roll holder)
171 735 h
63 dB
ESC/POS™
Windows XP, Windows VISTA (32/64bit),
Windows 7 (32/64bit), Windows 8 (32/64bit),
Opos, Linux, Android
INTERFACES
RS232 serial connector
USB connector
from 1200 to 115200 bps
12 Mbit/sec
MEMORIES
Receive buffer
2 Kbytes
Flash memory
1 Mbytes
Graphic memory
2 logos (608 x 430 dots)
PRINTER
Resolution
Printing method
Head life (2)
Printing width
203 dpi (8 dot/mm)
Thermal, ixed head
50 km
52 mm, 56 mm, 60 mm, 64 mm, 68 mm, 72 mm, 76 mm, 80 mm
65
Printing mode
Printing format
Normal, 180°
Height/width from 1 to 4, bold, reverse, underlined, italic
Character fonts
standard model
PC437, PC850, PC860, PC863, PC865, PC858, PC866, VISCII, U.D.P.
model with sempliied chinese font (3)
PC437, PC850, PC860, PC863, PC865, PC858, GB2312
model with extended chinese font (3)
PC437, PC850, PC860, PC863, PC865, PC858, GB18030
Printable barcode
Printing speed (2) (5)
UPCA, UPCE, EAN13, EAN8, CODE39, ITF, CODABAR,
CODE93, CODE128, CODE32, QRCODE
Normal = 100 mm/sec
High Speed = 130 mm/sec
PAPER
Type of paper
Paper width
Paper thickness
Paper weight
Recommended types of paper
External roll diameter
Paper end
Internal roll core diameter
Core type
Thermal rolls, heat-sensitive side on outside of roll
from 52 mm ± 0.5 mm to 80 mm ± 0.5 mm
63 µm ± 0.5 µm (for 55 g/m2 paper)
85 µm ± 0.6 µm (for 80 g/m2 paper)
from 55 g/m2 to 80 g/m2
KANZAN KF50 or KP460, MITSUBISHI PG5075 or TL4000
max 90 mm
Not attached to roll core
25 mm
Cardboard or plastic
Minimum ticket length
standard model
87 mm
model with motorized ejector
80 mm
CUTTER
Paper cut
66
Total
Estimated life (2)
1 000 000 cutter number
DEVICE ELECTRICAL SPECIFICATIONS
Power supply
24 Vdc ±10% (optional external power supply)
Medium consumption (4)
2.2 A
Typical consumption (5)
0.8 A
Stand-by consumption
0.05 A
ELECTRICAL SPECIFICATIONS POWER SUPPLY cod.963GE020000003 (OPTIONAL)
Power supply voltage
from 100 Vac to 240 Vac
Frequency
from 50 Hz to 60 Hz
Current (output)
2.5 A
Power
60 W
ENVIRONMENTAL CONDITIONS
Operating temperature
Relative humidity
from -20°C to +70°C
from 10% Rh to 85% Rh
Storage temperature
Storage relative humidity
from -20 °C to +70 °C
from 10% Rh to 90% Rh
NOTES:
(1) : Control board.
(2) : Respecting the regular schedule of cleaning for the device components.
(3) : For further information, refer to the commands manual for the chinese font management.
(4) : Referred to the UL measurements (L = 10cm, Density = 50% dot on, Print density = +50%).
(5) : Referred to a standard CUSTOM receipt (L=10cm, Density = 12,5% dots on).
67
7.2 Character speciications
Character set
Character density
3
11 cpi
15 cpi
20 cpi
35
45
64
Chars / sec
1540
1980
2773
Lines / sec
43
43
43
2.2 x 3
1.7 x 3
1.2 x 3
Number of columns
Characters (L x H mm)-Normal
NOTE: Theoretical values.
7.3
Device dimensions
Length
standard model
271.5 mm
model with motorized ejector
260.2 mm
Height
Width
102 mm
130.2 mm
Weight
standard model
1130 g
model with motorized ejector
1250 g
NOTES:
Data refer to device with paper roll holder assembled in the rear position (see par.3.2).
All the dimensions shown in following igures are in millimetres.
68
69
271.5
123.5
130.2
83
65.65
143.3
65.5
9.5
47
34.1
25
40.2
102
171.5
17.5
14.7
12.5
24
Standard model
44.86
89.72
53.8
18.5
115.5
Model with motorized ejector
102
45,3
1,8 exit ticket
130,2
89,72
65,65
44,86
171.5
143.3
34.1
65.5
123.5
83
12.5
260.2
53.8
17.5
104.2
70
7.4
Power supply dimensions cod.963GE020000003 (optional)
Length
127 mm
Height
35,5 mm
Width
56 mm
35,5
NOTE:
All the dimensions shown in following igures are in millimetres
AC INLET
56
N.C
2 1
3
GND
+24V
127
DC OUTPUT WIRE
71
7.5 Paper speciication
The following image shows an example of black mark placement on the non-thermal side of paper.
5
10,5
NON-THERMAL SIDE
min 106
21
PAPER WIDTH = 80
NOTE:
All the dimensions shown in following igures are in millimetres.
72
7.6
Character sets
The device has 3 fonts of varying width (11, 15 and 20 cpi) which may be accessed through programming or control
characters.
Each of these fonts offers the following code tables: PC437, PC850, PC860, PC863, PC865, PC858, PC866, VISCII, U.D.P.
PC437 CODE TABLE (Usa, Standard Europe)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
73
PC850 CODE TABLE (Multilingual)
74
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
×
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
®
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
Á
Â
À
©
╣
║
╗
╝
¢
¥
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
ã
Ã
╚
╔
╩
╦
╠
═
╬
¤
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
ð
Ð
Ê
Ë
È
ı
Í
Î
Ï
┘
┌
█
▄
¦
Ì
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
Ó
ß
Ô
Ò
õ
Õ
µ
þ
Þ
Ú
Û
Ù
ý
Ý
¯
´
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
SHY
±
‗
¾
¶
§
÷
¸
°
¨
·
¹
³
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
PC860 CODE TABLE (Portuguese)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ã
à
Á
ç
ê
Ê
è
Í
Ô
ì
Ã
Â
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
À
È
ô
ö
ò
Ú
ù
Ì
Õ
Ü
¢
£
Ù
₧
Ó
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
Ò
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
75
PC863 CODE TABLE (Canadian, French)
76
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
Â
à
¶
ç
ê
ë
è
ï
î
‗
À
§
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
È
Ê
ô
Ë
Ï
û
ù
¤
Ô
Ü
¢
£
Ù
Û
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
¦
´
ó
ú
¨
¸
³
¯
Î
⌐
¬
½
¼
¾
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
PC865 CODE TABLE (Nordic)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
₧
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
¤
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
77
PC858 CODE TABLE (Euro symbol)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
×
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
®
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
Á
Â
À
©
╣
║
╗
╝
¢
¥
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
ã
Ã
╚
╔
╩
╦
╠
═
╬
¤
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
ð
Ð
Ê
Ë
È
€
Í
Î
Ï
┘
┌
█
▄
¦
Ì
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
Ó
ß
Ô
Ò
õ
Õ
µ
þ
Þ
Ú
Û
Ù
ý
Ý
¯
´
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
SHY
±
‗
¾
¶
§
÷
¸
°
¨
·
¹
³
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
NOTA:
To print the Euro (€) symbol, the command sequence is: 0x1B 0x74 0x13 0xD5 (see Commands Manual).
78
PC866 CODE TABLE (Cyrillic)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
А
Б
В
Г
Д
Е
Ж
З
И
Й
К
Л
М
Н
О
П
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
Р
С
Т
У
Ф
Х
Ц
Ч
Ш
Щ
Ъ
Ы
Ь
Э
Ю
Я
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
а
б
в
г
д
е
ж
з
и
й
к
л
м
н
о
п
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
р
с
т
у
ф
х
ц
ч
ш
щ
ъ
ы
ь
э
ю
я
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
Ё
ё
Є
є
Ї
ї
Ў
ў
°
∙
·
√
№
¤
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
79
VISCII CODE TABLE (Vietnamense standard code)
80
Ẳ
Char
NUL SOH
Hex
0000
0001
0002
0003
Dec
0
1
2
3
Ẵ
Ẫ
BEL
BS
HT
LF
VT
FF
CR
SO
SI
0004
0005
0006
0007
0008
0009
000A
000B
000C
000D
000E
000F
4
5
6
7
8
9
10
11
12
13
14
15
ETX EOT
Char
DLE DC1 DC2 DC3
FS
GS
Ỵ
US
Hex
0010
0011
0012
0013
0014
Ỷ
0015
0016
0017
0018
0019
001A
001B
001C
001D
001E
001F
Dec
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
NAK SYN ETB CAN
Ỹ
SUB ESC
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
DEL
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ạ
Ắ
Ằ
Ặ
Ấ
Ầ
Ẩ
Ậ
Ẽ
Ẹ
Ế
Ề
Ể
Ễ
Ệ
Ố
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
Ồ
Ổ
Ỗ
Ộ
Ợ
Ớ
Ờ
Ở
Ị
Ỏ
Ọ
Ỉ
Ủ
Ũ
Ụ
Ỳ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
Õ
ắ
ằ
ặ
ấ
ầ
ẩ
ậ
ẽ
ẹ
ế
ề
ể
ễ
ệ
ố
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
ồ
ổ
ỗ
Ỡ
Ơ
ộ
ờ
ở
ị
Ự
Ứ
Ừ
Ử
ơ
ớ
Ư
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
À
Á
Â
Ã
Ả
Ă
ẳ
ẵ
È
É
Ê
Ẻ
Ì
Í
Ĩ
ỳ
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
Đ
ứ
Ò
Ó
Ô
ạ
ỷ
ừ
ử
Ù
Ú
ỹ
ỵ
Ý
ỡ
ư
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
à
á
â
ã
ả
ă
ữ
ẫ
è
é
ê
ẻ
ì
í
ĩ
ỉ
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
đ
ự
ò
ó
ô
õ
ỏ
ọ
ụ
ù
ú
ũ
ủ
ý
ợ
Ữ
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
8
CONSUMABLES
The following table shows the list of available consumables for device:
DESCRIPTION
CODE
67300000000406
THERMAL PAPER ROLL
width = 80mm
Ø external = 90mm
Ø core = 25mm
81
82
9
ACCESSORIES
The following table shows the list of available accessories for device:
DESCRIPTION
CODE
963GE020000003
POWER SUPPLY
(for technical speciications, see the paragraph 7.1)
ADAPTER CABLE FOR POWER SUPPLY
26900000000005
(see the paragraph 9.1)
26500000000356
USB CABLE TYPE A-B
Length = 1.8 m
26500000000311
SERIAL CABLE RJ-DB9F
Length = 1.5 m
83
9.1
Adapter cable for power supply
For the device is available an adapter cable (cod. 26900000000005) supplied as an accessory, for connecting the device
to the external power supply unit (cod. 963GE020000003 - optional).
Assembly instructions
Connect the adapter cable to the power supply unit as follows:
COM
84
24Vdc
10
ALIGNMENT
The device is provided with a sensor for the use of alignment notch in order to handle rolls of tickets with pre-printed ields and a ixed length.
The alignment sensor is a “relection” sensor: this kind of sensor emits a band of light and detects the quantity of light relected to it. The presence of the notch is therefore detected by the amount of light that returns to the sensor, considering that the light is relected by the white paper and absorbed by the black mark. To ensure the correct alignment, you must enable the “Notch Alignment” parameter during the Setup procedure (see
chapter 5).
The following paragraphs show how to correctly set the coniguration parameters of device in order to assure the alignment.
85
10.1
Calibration
The sensor calibration occurs automatically and consists in adjusting the quantity of light emitted to match the degree of
whiteness of the paper used and the degree of black of the mark printed on paper.
The device automatically performs the self-calibration during the Setup procedure only if the “Notch Alignment” parameter
is set to a value other than “Disabled” (see chapter 5).
When self-calibration starts, the device performs some paper feeds and then it prints the calibration result and the value
of the PWM duty-cicle of the alignment sensor driver so that it can be perform an optimal notch detection:
Autosetting Notch : OK
PWM Duty Cycle : 85.3%]
The “Autosetting Notch” parameter indicates the result of the self-calibration procedure; OK will appear if it has been successful, NOT OK will appear if the procedure has failed.
After the printing of the procedure result, the device offers the execution of the function of paper characterization “Characterize Paper” and the change of the “Notch Threshold” parameter which represents the detection threshold of the notch.
Choosing the “Yes” value for the “Characterize Paper” parameter, the device prints a graphic representation (see following
igures) of the outgoing voltage of the alignment sensor (expressed as a percentage) and the “Notch Threshold” value.
This graphic representation is useful to set the most suitable value to assign to the “Notch Threshold” parameter and then
to better identify the optimal threshold value which takes into account the variations of the signal and the small oscillations
around zero.
The following igure shows an example of paper with the non-thermal paper printed with black marks: the outgoing voltage is constant while passing the white paper between two notches and presents a peak at each black mark.
In this case, the optimal value for the “Notch Threshold” parameter is placed about half of the peak.
NON-THERMAL SIDE
Peak
THERMAL SIDE
“Notch/B.Mark
Threshold”
86
The following igure shows an example of paper with the non-thermal paper printed with black marks and other graphics (for example, a barcode): the outgoing voltage is constant while passing the white paper between two notches, presents a peak
at each black mark and presents some “noise” at each barcode. In this case, the optimal value for the “Notch Threshold”
parameter is located about halfway between the peak value and the maximum value of the “noise”.
LATO NON TERMICO
Picco
LATO TERMICO
“Notch/B.Mark
Threshold”
Rumore
If the maximum value of “noise” read by the sensor is very close to the peak value, it might be dificult to place the value of the “Notch Threshold” at an intermediate point. In these cases, it is mandatory that the portion of paper between the
point of printing end and the front notch is completely white (no graphics). In this way, the only next graphic detected by
the sensor for alignment after the printing end will be the notch.
87
10.2
Alignment parameters
The “alignment point” is deined as the position inside the ticket to use for the notch alignment.
The distance between the notch edge and the alignment point is deined as “Notch Distance”.
Referring to the front of the notch, the value of “Notch Distance” varies from 0mm minimum and 12.9mm maximum.
If the “Notch Distance” value is set to 0, the alignment point is set at the beginning of the notch.
Alignment
point
Alignment
point:
notch front
PRINTING DIRECTION
positive values
of “Notch Distance”
+
0
88
The following igure shows a section of the device with the paper path and the distances between the alignment sensor, the printing head and the cutter (cutting line), where
A = distance between the alignment sensor and the printing line = 12 mm
B = distance between the printing line and the cutting line = 12.5mm
A B
ESC/POS™ emulation
To deine the alignment point you need to set the device parameters that compose the numerical value of the “Notch Distance” parameter.
For example, to set a notch distance of 10mm between the notch and the alignment point, the parameters must be set on
the following values:
Notch Distance [mm x 10]
Notch Distance [mm x 1]
Notch Distance [mm x .1]
:1
:0
:0
The “Notch Distance” parameter, may be modiied as follows:
• during the Setup procedure of the device (see chapter 5)
• by using the 0x1D 0xE7 command (for more details, refer to the Commands Manual)
• by driver.
89
10.3
Printing area
In order to print ticket containing only one notch and to not overlay printing to a notch (that will make it useless for the next
alignment), it is important to well calibrate the length of the printing area of ticket according to the inter-notch distance.
The following igure shows an example of tickets with “Notch Distance” set to 0:
Cutting
line
Cutting
line
Printing
line
Printing
line
PRINTING DIRECTION
PRINTING
AREA
A
H
D
A
L
A
“Non-printable area” = “Distance between cutter/printing head”
where:
“Distance between cutter/printing head” = 12 mm
H Distance between the irst and the last print line, called “Height of the printing area”.
L
Distance between an edge of the notch and the next one, called “Inter-notch distance”.
D
Automatic feed for alignment at the next notch.
To use all the notches on the paper, you must comply with the following equation:
H + A ≤ L
The height of the printing area H can be increased to make no progress on alignment D but no further.
90
11
TECHNICAL SERVICE
In case of failure, contact the Technical Service by sending an e-mail to [email protected] detailing:
1. Product code
2. Serial number
3. Hardware release
4. Firmware release
To get the necessary data, proceed as follows:
1
3
XXXXXXXXXXXXXX
Rx
0000000000000000000
Write down the data printed
on the product label (see paragraph 2.3)
2
[email protected]
Customer Service Department
FW
Send an e-mail to the Technical Service,
with the data collected
TG2480H printer
-
rel 1.00
PRINTER SETUP
PRINTER TYPE
BOOT LOADER
BCODE
SCODE
HEAD VOLTAGE [V]
HEAD TEMP. [°C]
CUT COUNTER
POWERON COUNTER
PAPER PRINT [cm]
PWM NOTCH AVG.
= TG2480H
= rel.1.00
= <code>
= <code>
= 23.57
= 24
= 0
= 100
= 160
= 50%
Print a Setup report (see paragraph 5.1)
The Setup report shows
the firmware release
91
Part Number : 76200000001800 Rev.2.50
CUSTOM S.p.A.
World Headquarters
Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY
Tel. +39 0521 680111 - Fax +39 0521 610701
[email protected] - www.custom.biz
All rights reserved
www.custom.biz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement