DVD Player User's Manual
HY-DVD3-COVER
2005.9.30
9:58 AM
Page 2
DVD - 3/DVD - 3T
Preparations Connection
DVD Player User’s Manual
Setup
NOTICE:
For additional information or for the location of an authorized service center, please
contact KEC Mobile Applications / KTV USA, Inc. at (800) 524-1216 or (973) 470-9191
Use
KTV USA, Inc. 1 Madison Street East Rutherford, NJ 07073 800 524-1216 / 973 470-9191
KTV USA, Inc. © 2005
3406100490B
is the prohibition mark. If this appears when you operate the
product, wait until it disappears. If this phenomena repeats, the
current button does not cope with the disk in play.
Others
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 2
Safety Precautions
Do read and use the followings carefully for your safety and product protection.
Cautions are composed of Warning and Attention which mean
the followings respectively.
What is dewing?
is under sudden change of environment.
‘Dewing’ inside the DVD player may suspend
operation for 2 or 3 hours.
: Possibility of fatal injury or death
: Possibility of minor injury or product damage
To prevent dewing?
Preparations
The DVD player may create humidity when it
Supply power and leave the product at a dry
place for more than 2 hours to eliminate the
internal humidity.
Dewing occurs when
You move to a warmer outdoor place from a
room or car which is well air-conditioned in hot
summer.
You move to a warm room from a cold outdoor place in winter.
Put the cigar jack into the
deepest point to prevent
shaking.
Never use any damaged
cigar jack.
It may cause a poor contact or
fire.
It may cause a poor contact or
fire.
Never touch the cigar jack
with wet hands.
It may cause a fire or electric
shock.
Neither use nor store ignitable
sprays or inflammable materials in the vicinity.
Don’t put books or waterfilled vessels.
It may cause a breakdown.
It may cause an explosion or fire.
Don’t put metals(coin, hair
pin, ironware, etc.) or burnable foreign
materials(match, paper, etc.)
in the disk inlet or port hole.
Never hold the product
with your hands while the
disk is in play.
2
It may cause an accident.
Do not expand the cigar
jack too severely.
It may cause a breakdown of
disk or product.
Grab the cigar jack firmly
to pull it out.
Be careful not to get the
cigar jack cable entangled.
If not, it may cause a heat
emission or fire.
Watching or adjusting is
prohibited during drive.
It may cause a traffic accident.
It may cause the battery discharge from instable voltage.
Secure your vision from
the product.
It may cause a traffic accident.
Put the product at a flat
and stable place.
Otherwise, It may cause a
wrong operation.
Never disassemble or modify
the product on your own.
It may cause a breakdown.
Keep the remote control away
from the brake pedal.
It may cause a traffic accident.
It may cause a fire or electric
shock.
Avoid the vicinity of the handle knob for installation.
It may cause a traffic accident.
Keep the volume reasonable.
It may cause an interfering other drivers
and being ignorant of surrounding situation.
3
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 4
Special Features
Repeat Play(Title and Chapter for
DVD and Track and disc for VCD/CD)
Covers play MP3, WMA, and
JPEG(i.e. CD-R, CD-RW, DVD-R,
DVD+R, DVD-RW, and DVD+RW disk
containing MP3, WMA, or JPEG)
OSD(On Screen Display)
Press [DISPLAY] to display the information on
the DVD/VCD/CD disk and the device.
Screen Saver
High Performance Video(27Mhz/10bit)
Coaxial Digital Output(PCM, Dolby
Digital, dts)
Dolby Digital Decoder is built in.
Composite Video Output(x1)
S-Video Output(x1)
Slow Forward and Reverse
Playback(DVD)
Fast Forward and Reverse
Playback(DVD)
Title, Chapter, and Time Search for
DVD and Track and Time Search for
VCD/CD
Various Screen Ratio(DVD)
4:3 Zoom(Pan and Scan), 4:3 General(Letter
Box), and 16:9 Wide(Wide)
4
Repeat Play of Specific Area(A-B)
Selective Play(DVD/VCD/CD)
Title or Chapter for DVD and Track for Video
CD/CD
Various Voice Language(DVD)
Up 8 Voice Languages.
The number of languages depends on the disc
for SVCD and VCD.
Various Open Caption Language(DVD)
Up 32 Open Caption Languages.
The number of languages depends on the disc
for SVCD and VCD.
Various Angle Screen(DVD)
Simultaneous Multi Screen at Various
Angles(The number of screens depends on
the disc.)
Preparations
Use
Safety Precautions .......................................2
Special Features .....................................4
Disc Information ......................................6
Disc Handling and Storage......................7
Parts Name & Description(Front, Front
panel Display, Rear) ................................8
Parts Name & Description (Remote Control
Battery Change)........................................11
Parts Name & Description(Cautions for
Battery Handling)...................................11
Parts Name & Description (Name and
Function of Remote Control Buttons).....12
Precautions for DC Input/
Output Port Use.....................................14
Checking Accessories ...........................14
Disc Play(DVD, VCD, CD) . . . . . . . . . . .22
Checking DISPLAY . . . . . . . . . . . . . . . . .23
Checking disc Menu . . . . . . . . . . . . . . . . .23
Changing Disc Audio/Subtitle language
during the playback . . . . . . . . . . . . . . . . .24
Searching Video track/Music . . . . . . . . .25
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . .26
Repeat Play . . . . . . . . . . . . . . . . . . . . . . .27
Zooming-In/Angling . . . . . . . . . . . . . . . . .28
Searching Screen/Music . . . . . . . . . . . . .29
Playing MP3 and WMA Disc . . . . . . . . . .30
Photo View by JPEG Disc . . . . . . . . . . . .31
Connection
Screen Zoom
Preparations
Covers DVD, VCD, SVCD, and CDDA
Contents
Others
TroubleShooting . . . . . . . . . . . . . . . . . . .32
Product Specification . . . . . . . . . . . . . . . .34
Reference .............................................35
Connecting to TV/Audio . . . . . . . . . . . . .15
3D Sound Effect
3D Sound Effect Service
Free Volt
From 12V to 24V
Setup
Function Setup(Setup Menu) . . . . . . . . . .16
LANGUAGE Setup . . . . . . . . . . . . . . . . .17
DISPLAY Setup . . . . . . . . . . . . . . . . . . . .18
AUDIO Setup . . . . . . . . . . . . . . . . . . . . . .19
LOCK Setup . . . . . . . . . . . . . . . . . . . . . . .20
OTHERS Setup . . . . . . . . . . . . . . . . . . . .21
5
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 6
Disc Information
Disc Handling and Storage
Preparations
Even tiny scratch on the disc may affect the screen. Please take special care.
DVD(Digital Versatile Disc) is a disc with a maximum capability of 135 minutes
long image, 8 Disc Audio languages, and 32 Subtitle languages. It also has the
function of MPEG-2 type image compression and dolby digital 3D surround so that
you are able to bring a movie theater at home enjoying vivid image and clean
sound quality.
1
Disc Handling
Press the center holder to put a disc out of the case with
convenience.
Do not touch the disc surface but refer to the figure to
Both DVD player and disc have encoded country codes that you have to accord
with before use.
move a disc.
Do not stick paper or tape on a disc. It may be bent.
Do not leave fingerprint or dust on a disc. Be sure to check
and clean any before use.
Disc for Play
Disk Type
Disk Logo
Saved Signal
Disc Size
•
•
DVD VIDEO
DVD AUDIO
DVD-R
DVD+R
DVD-RW
DVD+RW
Audio + Video
Do not let dust or foreign materials on a disc.
Do not use broken or scratched discs.
12 cm
Disc Storage
VCD
Audio + Video
12 cm
Audio
12 cm
Without direct ray
Good ventilation
Available for vertical
storage
CD
CD-R
CD-RW
•
Dolby Digital
Digital Audio Disk
Stereo Disk
Broadcasting Method
Sudden temperature rise may dew the operating part or lens of a product, resulting in play failure.
If then, supply power and insert a disc 1 or 2 hours later.
Disc Handling
MP3 Disc
For a disc stained by fingerprints or dirty foreign materials,
wipe it out with neutral rinse and water and dry it with a soft
towel.
From inside to outside
Other discs than specified above shall not be used for this device.
DVD, DVD-Audio, DVD-ROM, and CD-ROM with an incompatible area code shall not
be used for this device.
The area code for the player is written in the back.
•
6
Do not use chemicals such as thinner, benzene, commercial rinse, alcohol, or static electricity preventive
spray for LP at all times. This may hurt the disc.
7
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 8
Parts Name & Description
1
Front Panel Display
3
2
4
5 6
1
7
1
POWER
8
9
7
Turns on/off power.
2
PLAY
8
4
Remote Sensor
Receives signals at a remote control.
5
NEXT/BACK
Skips chapters or tracks.
6
EJECT
Takes out discs.
STOP
1
9
2
10 AUDIO IN
Connects an audio cable with an audio input
port and an audio output port of other device.
6
7
DVD/SVCD/VCD/CD/MP3
Dolby Digital
3
7
4
ROTATE
Indicates a disc is rotating.
5
PLAY/PAUSE
Displays the current operation mode.
6
1
TITLE/CHAPTER
Displays the title or chapter information on the
DVD disc in play.
8
VISION
Displays the information on vision and operation modes such as Play, Stop, DiscConfirmed, or No-Disc.
ANGLE
Indicates the disc in play is being watched at
various angles.
10
8
Indicates the disc in play was recorded by
dolby sound effect.
VIDEO IN
Connects a video cable with a video input port
and a video output port of other device.
5
3
2
1
9
Displays the disc type inserted in the main
body.
Display Window
Shows the current condition of players or
discs.
Disc SLOT
Receives and discharges discs.
4
10
Stops disc operation.
Plays discs.
3
Preparations
Front
9
dts
Indicates the disc in play was recorded by dts
sound effect.
10 PBC (Play Back Control)
Displays the PBC operation condition while
VCD plays.
REPAT/ALL
Displays the current Repeat/Play mode.
8
9
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 10
Parts Name & Description
Parts Name & Description
Remote Control Battery Change
1
1. Push the battery lid in
the arrow direction to
open it.
MATE & LOCK
This device complies with part 15 of the
FCC rules. Operation is subject to the
Following two conditions.
(1) This device may not cause harmful
Interference, and (2) This device must
Accept any interference that may cause
Undesited operation.
DC 12-24V
IN
4
OUT REMOTE
SENSOR
5
6
VIDEO OUTPUT
7
6
7
AUDIO OUTPUT
DC INPUT
R-LINK IN/OUT
Allows remote control of any KEC Mobile
Applications video product in the R-LINK
chain even if it is hidden from view.
VIDEO OUT
AUDIO-L
8
AUDIO-R
9
DIGITAL OUT
10
The remote control can cover as long as 7m
from the DVD receiver and up to 30˚ to the left
and right.
EXTERNAL REMOTE CONNECTOR
S-VIDEO
Connect the S-Video cable with the S-Video
output port and TV S-Video input port for the
better resolution.
8
VIDEO OUT
Connect the Video cable with the Video output
port and TV Video input port.
DC INPUT
Use the DC power cable for connection.
5
3. Push the battery lid
back in the arrow direction to close it.
Use the external remote control cable.
Use the cigar jack for connection.(extra)
4
2. Put batteries in, checking
their polarity.
(1.5V, AAAx2)
Using Remote Control
S-VIDEO
Connect an audio cable with an audio output
port and an audio input port of other device.
3
➡
R-LINK
Connect a video cable with a video output port
and a video input port of other device.
2
➡
2
Class 1 Laser Product
3
1
Preparations
Rear
9
AUDIO OUT
Connect the Audio cable with the Audio output
port and TV or Receiver Video input port.
10 DIGITAL AUDIO OUT
Connect the DVD player with a compatible
Dolby Digital Receiver or Decoder or DTS
Receiver or Decoder.
Cautions for Battery Handling
Poor battery use may cause battery liquid leak or corrosion.
Check the polarity when you put batteries in.
Never expose a battery to heat or fire. Never disassemble or short a battery.
Check if a dead battery is in the remote control.
Never combine batteries of different type. Do not leave an old battery when you put a new
battery in.
When you don't use the remote control for a long time, please take out all batteries to prevent
their corrosion.
In case of poor operation of the remote control or shorter operation distance, replace the
batteries.
In case of battery liquid leak, clean the liquid from the remote control and replace the batteries.
10
11
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 12
Parts Name & Description
POWER (also on the DVD-3 front panel)
Press to turn the DVD player ON/OFF.
POWER OFF automatically activates AUX inputs.
DVD-3T Only: Press repeatedly to cycle through
DVD → TV → AUX.
2
16. PLAY (also on the DVD-3 front panel)
Press to begin disc play.
DVD-3T Only: Adds the channel to memory.
17. PREVIOUS (also on the DVD-3 front panel)
Press once to go to the start of the current chapter (DVD) or track
(VCD, CD, MP3).
Press again to go to the start of the previous chapter/track.
EJECT (also on the DVD-3 front panel)
Press to eject the disc.
1
3
2
4
5
6
3
4
7
8
9
5
10
11
12
14
15
13
16
S-TITLE
Use to choose and cycle through the available
subtitles. This function will only work if the disc
contains subtitles.
19
8
18
20
9
23
25
24
26
Press to advance to the next chapter or track.
20
ANGLE
21
22
23
VOLUME
24
Adjusts the audio output levels of the DVD-3 to equalize its output with other
program sources in the vehicle (VCP, Video Game, etc).
IMPORTANT NOTE: If the DVD-3 Volume Control is set to “0”, no sound
will be heard regardless of the settings of any other system volume controls.
25
ZOOM
26
MUTE
14
STOP (also on the DVD-3 front panel)
Stops disc play.
DVD-3T Only: Erases TV channel from memory in TV mode.
29
15. PAUSE
CD: The audio will be paused.
DVD: Still frame mode. Press repeatedly to advance the picture frame
by frame.
DVD-3T Only: Starts automatic channel scan.
DISPLAY
Moves to the title/track or chapter of a disc.
SLOW FORWARD
Press repeatedly to slow forward through the disc from 1/2X to 1/32X slower.
Audio will be muted.
27
NUMERIC BUTTONS
May be used to make direct selections from various menu screens.
DVD-3T Only: May be used for direct entry of the desired channel.
28
Cuts off the sound.
27
SLOW BACK
Press repeatedly to slow reverse through the disc from 1/2X to 1/32X slower.
Audio will be muted.
GOTO
Use to go to the track or chapter of the DVD disc you want.
13
SETUP
Press to display the DVD-3’s built-in SETUP Menus for Language, Video,
Audio and Parental Control.
MODE
Repeats the selected segment.
12
ENTER
Use to choose the desired menu item.
MENU
A-B
ARROW KEYS / CH+, CH- KEYS
Use to move through the desired menu.
DVD-3T Only: Use Up/Down to change channels & Left/Right to fine
tune channels.
Zooms in on picture.
11
FF
Press repeatedly to fast forward through the disc from 2X to 100X
faster. Audio will be muted. (DVD)
TITLE
Use to choose play or repeat mode.
10
28
19. NEXT (also on the DVD-3 front panel)
Use to cycle through soundtracks in various
languages. This function will only work if the disc has been recorded
with multiple language soundtracks.
Displays the menus of the disc being played.
17
21
Press repeatedly to fast reverse through the disc from 2X to 100X
faster. Audio will be muted. (DVD)
LANGUAGE
Displays the titles on the disc under play.
7
22
18. FR
Use to access various camera angles. This function will only works if
he disc has been recorded with multiple camera angles.
6
Preparations
1
Name and Function of Remote Control Buttons
29
TV/AUX
Press to cycle between DVD → AUX playback.
DVD-3T Only: Press to cycle through DVD → TV → AUX.
NTSC/PAL
Press STOP button and then press NTSC/PAL button to select the
desired mode.
IMPORTANT NOTE: The DVD-3 is preset at the factory for NTSC
mode. Do not use this button unless you need to set the player for use
outside of the USA or other NTSC countries.
NOTE: Buttons 1~2 & 14~20 are duplicated on the Tri-Mode Remote Controller (Part # RC9799 or RR9799) that is packaged with
all KEC MOBILE APPLICATIONS LCD Systems. The RC9799 or RR9799 lœœ TRK/CHAP √√l buttons also function as
Channel +/- buttons with the DVD-3T. (Please see the Reference Section of this manual for more information).
12
13
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 14
Connecting to TV/Audio
Precautions for DC Input/Output Port Use
1
When using the DC power supply cable(DC Power Supply Cable)
Connect the red cable port to ACC (DC 12V~24V) and the black one to the ground.
Wiring Diagram
When using the AUX input port of the head unit
Use ➃ of Page 10.
DC 12-24V
MATE & LOCK
When using the car cigar jack(Extra Goods)
Check if the car cigar jack output voltage is DC 12V ~ 24V before you put it in the
DC input port.
Use ➂ of Page 10.
Attention : Do not use the
cigar jack cable while the DC
power cable is in use.
Connection
2
DVD Player
This device complies with part 15 of the
FCC rules. Operation is subject to the
Following two conditions.
(1) This device may not cause harmful
Interference, and (2) This device must
Accept any interference that may cause
Undesited operation.
R-LINK
Class 1 Laser Product
IN
OUT REMOTE
SENSOR
S-VIDEO
VIDEO OUT
AUDIO-L
AUDIO-R
DIGITAL OUT
Connect the DC power supply cable to
the head unit power supply cable.
DC Power
Supply Cable
Cigar Jack
Cable
Checking Accessories
Audio Cable
Head Unit
Video Cable
Attention : Do not use the DC power supply cable
while the car cigar jack cable is in use.
Remote
Control
AAA
Cells
Do not use.
TV A/V Cable
Connect to AV1 or AV2.
Remote Control Sensor
LCD TV (monitor)
12V DC, A/V&
R-Link Cables
Remote IR
Sensor #RESMC
Mounting Sleeve
Faceplate Frame
Owner’s Manual
& Warranty Card
Mounting
Hardware
AC Adaptor
12V Cigar Plug
Adaptor
1
Connect the audio cable to the Audio Output(L/R) port in the back of the
DVD player and the Audio Input port of the car stereo.
2
Connect the video cable to the Video Output(L/R) port in the back of
the DVD player and the Video Input port of TV.
Option Accessories
Please call the shop where you bought our product to buy other extra goods than
specified above.
14
15
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 16
Function Setup
DVD Setup
Press SETUP when a disc is not running to enter DVD and the following screen to preset
various menus will appear as follows. Here comes the information of display.
The default setting will be left unchanged by power on or off.
LANGUAGE Setup
Using Setup Menu
Press [SETUP] button when a disc
is not running
1
•
•
1
Press [SETUP] button of the remote
control when a disc is not running
❿ button to move to the
and press ➛❿
LANGUAGE Setup menu.
2
Press ❷button to enter the LANGUAGE
SETUP menu and press ❿, œ and ❷
buttons to select a language.
Press ➛ button to return to the previous menu during DVD
setup.
Press ➛ ❿ button to move to the SETUP menu.
•
It changes in the order of LANGUAGE ➝ DISPLAY ➝ AUDIO ➝
LOCK ➝ OTHERS.
LANGUAGE Setup
Refer to LANGUAGE of Page 17.
You can set up Menu language, Disc Audio, Sub-title, and Disc Menu languages.
DISPLAY Setup
Refer to DISPLAY of Page 18.
You can select Screen Size, Progressive Scan, or Broadcasting Method.
Refer to AUDIO of Page 19.
AUDIO Setup
You can set up the Audio Digital/Analog output method.
LOCK Setup
Refer to LOCK of Page 20.
You can select the x-rating for minors.
OTHER Setup
Refer to OTHERS of Page 21.
You can set up various functions.
Setup
2
The SETUP menu appears.
Sets up the Menu language, Disc Audio, Subtitle languages recorded in a disc to see or hear a
language that you want to.
Menu Language
Selects the menu language for the DVD player
Disc Audio
Selects the Disc Audio language.
Disc Subtitle
Selects the Subtitle language.
Disc Menu
Selects the Disc Menu language.
3
Press ❷ button to enter the detailed menu, press ❿ button
to enter a sub menu, and press œ and ❷ buttons to select
the sub menu.
Press [ENTER] button.
4
16
4
Press [ENTER] button.
5
Press SETUP button to exit the default menu.
•
•
•
•
Setup process is complete.
Press SETUP button to escape from the default menu.
Setup process is completed.
Exits the default menu.
•
If the set menu language is not written on the disc, the menu is not displayed into the set
language.
17
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 18
DVD Setup
DISPLAY Setup
Here are the display setup options.
2
Press ❷ button to enter the DISPLAY
Setup menu and press ❿, œ and ❷
buttons to select a display.
TV Aspect Size
- 16 : 9 : You can see the screen in the ratio of 16 : 9.
- 4 : 3 : You can see the screen in the ratio of 4 : 3.
Display Mode
- Letterbox : You can see the full screen in the ratio of 16:9 but a black margin will
appear both on the top and at the bottom respectively instead.
- Panscan : You can cut both sides of the 16:9 screen to zoom in the central part.
Depending on the active Audio Speaker condition, you can set up as follows.
1
Press [SETUP] button of the remote control
when a disc is not running and press ➛ ❿
button to move to the AUDIO Setup menu.
2
Press ❷button to enter the AUDIO
Setup menu and press ❿, œ and ❷
buttons to select the menu for setup.
Setup
1
Press [SETUP] button of the remote control
when a disc is not running and press ➛ ❿
button to move to the DISPLAY Setup menu.
AUDIO Setup
Dolby Digital Output
- Bitstream : When connecting with Dolby Digital Decoder
- PCM : When connecting 2CH Output
DTS Output
- Bitstream : When connecting with DTS Decoder
- PCM : When connecting 2CH Output
PCM Sampling Frequency
- 48 KHz : When the active AMP can not deal with the 96KHz signal
- 96 KHz : When the active AMP can not deal with the 96KHz signal
3
Press [ENTER] button.
•
•
Setup process is completed.
Press SETUP button to exit the setup menu.
Digital Output
- On : When turning on Digital Output
- Off : When turning off Digital Output
3
18
Press [ENTER] button.
•
•
Setup process is completed.
Press SETUP button to exit the setup menu.
19
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 20
DVD Setup
LOCK Setup
OTHERS Setup
This function keep children off violent or erotic materials by setting the rating from 1 to 8.
For the disc without a proper rating, this function is not applicable.
2
Press ❷ button to enter the Rating
Setup menu and press ❿, œ and ❷
buttons to select a rating.
Rating
- Rating 1,2 : For every age(a disc free of obsceneness,
violence, drug, or insult)
- Rating 3 : Under parents' instruction or recommendation, Improper for young kids(a
disc containing violence but free of plain obsceneness or drug)
- Rating 4,5 : In the attendance of parents under the age of 13(a disc free of sexual
act or excessive violence)
- Rating 6 : In the attendance of parents under the age of 17(a disc for adult containing insult, violence, sexual act, and drug)
- Rating 7,8 : Over the age of 17 only(a disc for adult only containing playing sexual
act and excessive violence)
Password
- New Password : Input a new password.
- Confirm : Input a new password again.
Press [ENTER] button.
3
•
•
•
20
1
Press [SETUP] button of the remote control
❿
when a disc is not running and press ➛❿
button to move to the OTHER Setup menu.
2
Press ❷ button to enter the OTHERS
Setup menu and press ❿, œ and ❷
buttons to select an item for setup.
PBC (Play Back Control)
This function is applicable to VCD 2.0 for the quick search
of a shot by using the menu recorded in a disc.
Auto Play
This function is applicable to the play of DVD to jump to the Watching Movie menu, ignoring
the initial ad or Root menu for disc play.
B.L.E
Darken the screen at night.
Load Default
Returns to the ex-work default.
Screen Saver
Screen Saver is used to prevent TV or monitor in use from being damaged.
When you stop or pause the DVD player for more than 3 minutes, the DVD logo screen will
start moving.
Last Play
Starts the playback from the point where the playback stopped before.
Setup process is completed.
Press SETUP button to exit the setup menu.
For the disc without a proper rating, LOCK function is not applicable.
Setup
1
Press [SETUP] button of the remote control
when a disc is not running and press ➛ ❿ button to move to the LOCK Setup menu.
3
Press [ENTER] button.
•
•
Setup process is completed.
Press SETUP button to exit the setup menu.
21
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 22
Checking DISPLAY
DISC PLAY
Depending on the disc type, the Voice Language/Closed Caption function operates.
This function is available only during play.
Before playing a disc
1
Check if the area code of your DVD player accord with that of a disc. If not, the disk won't operate.
1
DVD
The current title, chapter, time, disc audio language, subtitle language, camera, and 3D
sound effect will be displayed in the screen.
(DVD, VCD, CD)
Playing a disc
Press [DISPLAY] button.
VCD
The current track, time, disc audio language, and 3D sound effect will be displayed in the
screen.
Press [POWER] button.
Checking Disc Menu
2
Let the labelled side(containing no data) of a disc face up
and put the disc in.
•
For the disc containing Menu, you may select one out of the various menus as follows.
The disc will automatically operate.
1
Stop() Button
Stops play.
The menu in the disc will appear.
The menu differs by the disc.
Whenever you press MENU button, PBC will be turned on and off in turn.(VCD 2.0)
Pause(ll) Button
- Pauses play of a disc.
- Whenever you press this button, the screen will change one by one.
- Press ❿ button again to replay the disc.
CD and VCD1.1 don't have this function.
2
•
22
Use
❿) Button
Play(❿
- Press ❿ to play the point whose play was suspended before.
- Press twice and press ❿ again to play a disc from the beginning.
•
Press [MENU] button.
Press ❷, ❿, œ and ❷ buttons to move to an item and
press [ENTER] button.
•
What is Title?
Refers to a movie file recorded in a DVD disc.
•
What is Chapter?
Refers to each chapter, a unit which classifies a movie file recorded in a DVD disc.
•
What is Track?
Refers to a unit or a music which divides a scene recorded in a VCD or CD list.
In 3 minutes after a disc is paused, the DVD player will automatically enter the Screen Saver mode to protect
your TV.
If you don't pull a disc out in 10 seconds after you press EJECT button to eject the disc, it will be automatically
loaded, eventually the disc will stop.
23
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 24
Changing Disc Audio/Subtitle language during the Playback
Searching Video track/Music
Depending on the disc type, the Disc Audio/Subtitle function may not operate.
This function is available only during the playback.
During disc play, use the following functions to search a video track or a music.
Changing Disc Audio
1
(DVD, VCD)
Press [DISPLAY] button.
Quick Search of Screen/Song (DVD, VCD, CD, MP3)
1
Press FR and FF and (
during play.
) button in the remote control
DVD
The play speed will change x2 ➝ x4 ➝ x16 ➝ x100 by pressing the button.
Press œ❷ buttons to select the Disc
Audio and ➛ ❿buttons to select the
language.
2
For the disc containing the disc audio information, press LANGUAGE to select a variety of
languages such as Kor, Eng, etc.(DVD)
•
•
•
The subtitle language mark may vary with the disc type.
A disc can contain as many as 8 subtitle languages.
If you want the disc audio language whenever you play DVD, set a disc audio language in the
default setup.(See Page 19.)
Changing Subtitle Language
VCD/CD
The play speed will change x2 ➝ x4 ➝ x8 by pressing the button.
MP3
The play speed will change x2 ➝ x4 ➝ x8 by pressing the button.
Press
PLAY button to recover the normal play speed.
During quick play, sound will be mute.(DVD/VCD)
(DVD)
1
Press [DISPLAY] button.
2
Press œ❷ buttons to select a subtitle language, and ➛ ❿ buttons to fix
the subtitle language.
1
Use
Skipping Chapter(Track)
(DVD, VCD, CD, MP3)
Press BACK and NEXT (
) button in play.
When pressing Back(
) button,
it returns to the previous chapter.
When pressing NEXT(
) button,
it moves to the next chapter.
For the disc containing the subtitle information, press S-TITLE button to select a variety of
languages such as Kor, Eng, Jap, etc.
Press S-TITLE button to turn it off and the subtitle won't appear any more.
•
•
•
•
•
•
24
The subtitle language mark may vary with the disc type.
A disc can contain as many as 32 subtitles.
If you want the same subtitle language whenever you play DVD, set a subtitle language in the
default setup.(See Page 24.)
The Disc Audio/Subtitle language selection function may be available depending on the disc
type.
It won't operate after paused.
It is available only during DVD play.
25
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 26
Slow Play
Repeat Play
(DVD/VCD)
Slow Play
1
Press SLOW (
) button in PAUSE or PLAY.
When pressing SLOW button (
),
it plays with x1/2, x1/4, x1/8, x1/16, and x1/32 in the forward direction.
),
When pressing SLOW button (
it plays with x1/2, x1/4, x1/8, x1/16, and x1/32 in the reverse direction.
Press PLAY (
) button to recover the normal play speed.
During slow play, the sound will be mute.
This function is not available while CD, MP3 or WMA plays.
1
Press PAUSE (
(DVD/VCD)
) button after a disc was paused.
Whenever you press it, the screen will proceed one by one track.
Press PLAY(
) button to recover the normal play speed.
Press MODE (
) button during
the disc playback.
1
Whenever you press MODE button, the mode will
keep changing in the following sequence.
DVD
Chapter ➝ Title ➝ Off
VCD
Track ➝ All ➝ Off
CD, MP3
Track ➝ Random Play ➝ All
DVD
- Off : When not playing in repeat
- Title : When playing the current title in repeat
- Chapter : When playing the current chapter in repeat
VCD
- Off : When not playing in repeat
- Track : When playing the current track in repeat
- All : When playing the current disc in repeat
CD, MP3
- Track : When playing the current track in repeat
- Random Play : When playing in Random
- All : When playing the current disc in repeat
Repeating Certain Area
•
•
The sound will be mute during this function is activated.
This function is not available while CD, MP3, or WMA plays.
Use
Dividing Screens
Repeating Play of Chapter, Title & Track(Music) (DVD/VCD/CD)
(DVD/VCD/CD)
Press Repeat Area (
) button at
the point that you want to repeat
playing.
1
Press the button at both the start point(marked 'A') and the
end point(marked 'B') of the area that you want to repeat
playing. Only the selected area will be played over and
over again.
Press the button once more to cancel this setup.
•
26
The function may not be available depending on the disc
type.
27
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 28
Zooming-In/Angling
Searching Screen or Music
You may search a screen or a Music by Progress or Title/Chapter/Track.
(DVD/VCD)
Zooming-In
Searching by Time
You may zoom the screen by 2 steps during play or pause.
1
Press ZOOM (
)button in the
Play or Pause mode.
The convex mark ( ) will be displayed presenting zoom ratios.
Whenever you press the button, the screen will be zoomed by
the following ratio.
400% ➝ 1600% ➝ off
2
Press œ,❷, ➛ and ❿ buttons to move the zoomed area.
1
Press Search (
2
Press œor ❷ button to move to the
Time menu.
3
) button.
If you want to search 1hr 5min 15sec, press
1, 0, 5, 1, and 5 followed by ENTER button.
Then the screen after the selected hour will be
played.
3
(DVD)
When a disc contains an area shot at various angles, you may see the screen at those angles.
1
Press ANGLE (
)button.
Searching by Title or Chapter
1
The mark (
) will be displayed, presenting the maximum number of screen.
Press ANGLE button to select the screen at an angle.
In case the maximum number of screen is 1, the screen
angle won't change.
2
3
28
Use
Changing the Camera Angle
Press Search(
) button.
Press œor ❷ button to move to the
Title/Chapter menu.
If you want to search Title 1, Chapter 3, press 1 and 3
followed by ENTER button.
You have only to input the chapter to move in the same title.
29
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 30
Playing MP3 and WMA Disc.
Photo View by JPEG Disc
Playing File
Put in a Disc.
1
Photo View by JPEG Disc
Make the printed side of the disc face upward.
As it enters, the first song is automatically played.
Press STOP
Press PAUSE
Press PLAY
button to stop play.
button to pause play.
button to replay.
1
Put a disc in.
Make the printed side of the disc face
upward.
1. Press œ❷ button to select a photo.
2. Press NEXT/BACK button while a photo is viewed to
move to the next/previous photo.
3. Press ➛ ❿button to rotate the photo by 90˚ > 180˚ > 270˚ > ORIGINAL step by step.
4. Press ZOOM button to see the screen at the zoom ratio of 400% ➝ 1600% ➝ Normal step
by step.
If you want to play a music.
1. Press œ❷ button to select a music(track) followed by ENTER button. A music will be
played.
2. Input number keys and use ENTER button to play the music of a number rightly.
•
•
•
•
•
•
Only the files with the extension of JPG/JPEG are to be viewed.
The JPG file name shall not contain special marks (\,/,:,*,!,<,>,|,...)
Select the middle (
) from the list to adjust the view speed in the order of ( ➝ ➝
➝
)
Up to 6 tracks will be appeared per display.
Press( ) or ( ) button to listen to the next or previous music.
Press SLOW (
) button to select a music in the other folder.
Use
❉ About MP3, WMA File
•
•
•
•
•
MP3 or WMA files shall be in the format of ISO 9660 or JOLIET.
The file name of MP3 or WMA shall not contain special marks( \,/,:,*,!,",<,>,|... )
You are not allowed to record unwritable MP3 or WMA files.
MP3 and WMA discs may not be played depending on the recording condition.
WMA files may not play the data less than 48Kbps, 33kHz..
If you want to listen to only the music that you want to;
1. Press œ❷ button to move to a music and press ❿ button until it appears. Then, press
(ENTER) button to register the music in the program list.
2. Press ➛ ❿ button to move to the program, and press ENTER button.
•
: When registering the whole list in the program
•
: When deleting the music from the program
•
30
: When deleting all the music from the program
31
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 32
Troubleshooting
Take the following measures at first and further turn the product off and call our
Service Center.
•
•
•
The disc is running but the screen
does not appear or it is poor or
shaking.
•
•
•
Check if TV is turned on.
Check the connection.
Check if the main body is paused.
Check if the disc contains foreign materials or is
damaged.
Check the original condition of the disc.
•
No sound
•
•
•
The sound quality is not even.
The remote control does not operate.
•
•
•
•
There is no image or sound or the
disc come out in 2~5 seconds.
Isn't the product installed in too cold or hot place?
The optimum temperature for the operation ranges
0°C~ 50°C
•
•
•
Check the existence of a disc.
Check the power voltage.
Check if the right side of a disc was faced upward.
Check if the disc area code.
Check the disc condition.
•
•
TV Aspect selection is impossible.
•
•
Dolby Digital 5.1CH 3D sound
effect does not come out.
Disc Audio or Subtitle language which was selected
does not operate.
•
•
During DVD play, the Screen
Angle doesn't operate.
32
By the specification, some discs may not obey the
default condition. Only the disc that has the same
function with the SETUP menu will operate.
DVD discs are manufactured in the 16:9 Wide, 4:3
Movie, and 4:3 Zoom screen according to the manufacturing condition. Each type always its own rated
screen.
Check the DVD disc case to select the function
proper for a motion. For your reference, the 4:3
standard disc may not be seen wide.
Dolby Digital 5.1CH 3D sound effect can be heard
by the combination of the Dolby Digital exclusive
lamp. In addition, only the DVD disc recorded by
'Dolby Digital 5.1CH' may operate.
Others
•
The product does not operate
as per the initial setup condition.
Check the angle and distance of the remote control. Check any obstacle.
Check if batteries are sufficiently charged.
•
•
Nothing plays.
Check the connection with the Dolby Digital Lamp.
Check the connection plug.
Check if the connection port is stained with foreign
materials.
Aren't you operating in the SLOW or SEPARATE
mode? (There will be no sound in the Flexible
Speed Screen Play mode.)
Check the connection and further if SETUP is correct.
Is the disc inserted right?(Make the printed side of
the disc face upward.)
Check the disc condition.(Keep it clean.)
Only the disc audio/subtitle language recorded in a
DVD disc can be played.
Screen Angle is available only when the content by
angles is recorded in a DVD disc. In such a case,
the angle mark
shall be printed in the product or
VFD.
33
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 34
Product Specification
REFERENCE
KEC MOBILE APPLICATIONS TRI-MODE REMOTE CONTROLLER # RC9799 (or # RR9799)
DVD Mode Video Output Method
TV Mode Broadcasting Method
NTSC/PAL
Voice Response
20Hz ~ 20KHz
Voice S/N Ratio
90dB
Audio Analog
Output
0.5Vp-p Impedance : 75 Ω
Audio Digital
0.5Vp-p Impedance : 75 Ω
Video
1.0Vp-p Impedance : 75 Ω
Power
DC 12V~24V, 1.5A
Power Consumption
18W
Product Size
178(D)x175(W)x50(H)
Weight
1.3Kg
Allowable Operating Temperature
0°C ~ 50°C
Allowable Operating Humidity
0% ~ 80%
Allowable Operating Condition
Horizontal
The Tri-Mode Remote Controller is packaged with most KEC LCD Systems. In addition to
full remote
control of the LCD System, it also provides basic remote control commands for our DVD
and Videocassette
Players.
To control the DVD-3 with the RC9799 (or # RR9799), press the DVD MODE button.
To change to VCP control, press the VCP MODE button.
Notes:
• The LCD System control buttons are always available. They are not affected by the DVD/VCP
MODE buttons.
• This unit is not a universal remote controller. It is only designed to transmit control codes to KEC
Mobile Applications products.
❉ Design, accessories, and product specification may be changed without notice.
Others
34
35
HY-DVD3-ENG
2005.9.30
11:40 AM
Page 36
REFERENCE
A NOTE TO INSTALLERS CONCERNING THE KEC R-LINK SYSTEM
Most KEC Mobile Applications video products (TV, LCD, VCP & DVD) employ our R-LINK
System. This
allows all of our components to be remote controlled even if some of the components are
hidden from view.
If you are installing the DVD-3 along with one of our TV’s or monitors and one of
our VCP’s:
1. Connect an R-Link cable from the KEC TV/Monitor to the DVD-3’s R-Link Input
2. Connect an R-Link cable from the DVD-3’s R-Link Output to the R-Link jack on the
rear panel of the KEC VCP.
All KEC components may now be remote controlled by pointing any of the KEC
remote controllers at the remote sensor on any of the KEC components.
Please note that since pairs of KEC Mobile Applications Headrest Monitors are designed to be operated independently of each other, they are not equipped with R-Links. Please refer to the installation
information accompanying our Headrest Monitor Systems for information on the use of R-Link in conjunction with those systems.
36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement