C002 JR Hand Tool Operating Instructions

C002 JR Hand Tool Operating Instructions
Operating
Instructions
C002 JR
Hand Tool
To Install a BAND-IT Junior Clamp:
1
3
Place BAND-IT tool in vise. Insert Clamp in Tool and
grip end of band by Band Gripper Lever.
Roll hose over approximately 30° BACKING OFF
TENSION HANDLE ¼ to ½ turn only, through course
of rollover, depending on type and size of hose. Grip
buckle with hook in nose by pushing cutter handle.
Push cutter handle farther to cut the band completing
BAND-IT JR. Clamp.
2
Insert hose in clamp. Take up clamp by turning the
handle of BAND-IT TOOL clockwise. To feel
movement of band, place finger on BAND-IT BAND
at buckle edge while tensioning with tool handle.
When you no longer feel band moving through
buckle, even as you turn handle, MAXIMUM
PRESSURE IS EXERTED BY BAND-IT BAND, and
you should stop turning handle.
4
The finished BAND-IT JR. Clamp –
NOTE: USE OF VISE IS OPTIONAL
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 1 of 3
Document # P45087 rev. E
© Copyright
BAND-IT-IDEX, Inc. 2002
All rights reserved
Repair Parts &
Assembly
C002 JR
Hand Tool
NOTES:
1. TO ASSIST IN REMOVING THREADED PARTS, APPLY HEAT
(SOFTENS LOCKING COMPOUND.
2. WHEN CONNECTING ITEM 6 (TENSION SCREW) TO ITEM 3
(SLIDE BLOCK), OR ITEM 22 (BUTTON HEAD SCREWS) TO ITEM 14
(JR. ADAPTER BODY) CLEAN THREADS (MALE AND FEMALE)
OF FOREIGN MATTER, THEN APPLY TWO DROPS OF HIGH
STRENGTH LOCKING COMPOUND (LOCTITE 271 OR EQUIV.)
ONTO MALE THREADS AND CONNECT PARTS TOGETHER.
3. BEFORE USING BAND-IT JUNIOR TOOL CHECK TO SEE THAT
THE CUTTER BLADE ITEM 17 AND BACKING PLATE ITEM 18 ARE
FULLY TIGHTENED. LOOSE SCREWS CAN CAUSE BREAKAGE
OFR CUTTER BLADE OR BACKING PLATE. USE (ITEM 19) HEX
KEY PROVIDED WITH TOOL TO TIGHTEN SCREWS IF NEEDED.
4. ASSEMBLE ITEM 11 (TENSION HANDLE) THEN ATTACH ITEM 10
(RETAINING RING, TEN. SCREW) TO ITEM 6 TENSION SCREW IN
LOCATION SHOWN. PLACE RING ON GROOVE, THEN PUSH RING
AGAINST A HARD SURFACE SUCH AS A TABLE UNTIL IT SNAPS
SECURELY IN PLACE.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 2 of 3
Document # P45087 rev. E
© Copyright
BAND-IT-IDEX, Inc. 2002
All rights reserved
C002 JR
Hand Tool
Warranty
Unless sold without warranty, BAND-IT products are warranted to be free from
defective workmanship and/or materials for a period of one year from the date of
purchase. Warranty on tools is void if clamps not meeting BAND-IT specifications are
used, or if the tool is altered or abused in any manner, including lack of lubrication or
used for any purpose in any way not intended by the manufacturer as specifically
covered by the instructions accompanying the tool. Specific tool components, such as
knives, blades and grippers, which are subjected to normal wear, are excluded from
this coverage, as component life depends on usage of the tool. Tools that are
repaired or sold as used by BAND-IT are subject to a warranty of 90 days from date of
shipment. NO OTHER WARRANTY OF ANY KIND WHATSOEVER, EITHER ORAL
OR WRITTEN, INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, OR OTHER WARRANTY OF QUALITY
IS EITHER EXPRESSED OR IMPLIED FOR THE PERFORMANCE OF BAND-IT
PRODUCTS. BAND-IT SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL,
AND/OR CONSEQUENTIAL DAMAGES, EVEN IF BAND-IT HAS BEEN NOTIFIED
OF THE POTENTIAL OF SUCH LOSS OR CLAIM. (8/02)
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 3 of 3
Document # P45087 rev. E
© Copyright
BAND-IT-IDEX, Inc. 2002
All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement