DS 616 Release 2 - iDCS Keyset User Guide

DS 616 Release 2 - iDCS Keyset User Guide
TABLE OF CONTENTS
iDCS KEYSET
USER GUIDE
ABOUT THIS BOOK ..........................................................1
THINGS YOU SHOULD KNOW
............................2–8
ASSEMBLING YOUR KEYSET ..................................9
ADDING AN iDCS 14B KEY STRIP ......................10
OUTSIDE CALLS
SAMSUNG DS 616 SYSTEMS
Making an Outside Call ....................................................................11
Answering an Outside Call ................................................................11
Universal Answer ..............................................................................11
Recall/Flash ......................................................................................12
Busy Line Queuing with Callback ....................................................12
Canceling Callback............................................................................12
INTERCOM CALLS
June 2004
Calling Other Stations........................................................................13
Answering Intercom Calls..................................................................13
Voice Announce Mode ......................................................................13
Answer Modes ..................................................................................13
Busy Station Callback ......................................................................14
Busy Station Camp-on ......................................................................14
Calling Your System Operator ..........................................................15
CALL PROCESSING
Samsung Telecommunications America reserves the right without prior notice to revise information in this guide for any reason. Samsung Telecommunications America also reserves the
right without prior notice to make changes in design or components of equipment as engineering and manufacturing may warrant. Samsung Telecommunications America disclaims all
liabilities for damages arising from the erroneous interpretation or use of information presented
in this guide.
Holding Calls................................................................................16–17
Transferring Calls ........................................................................18–19
Transfer with Camp-On......................................................................18
Transfer to Voice Mail ........................................................................18
Call Waiting ........................................................................................19
Conference Calls ..............................................................................19
Forwarding Calls ..........................................................................20–22
Call Pickup ........................................................................................22
Group Call Pickup ............................................................................22
DIALING FEATURES
Speed Dialing ....................................................................................23
Programming Personal Speed Dial Numbers ............................23–24
One Touch Speed Dialing ................................................................24
Last Number Redial ..........................................................................24
Save Number with Redial ..................................................................25
Chain Dialing ....................................................................................25
Automatic Redial/Retry ......................................................................25
Pulse to Tone Changeover ................................................................26
PAGING AND MESSAGING
Making an Internal Page....................................................................27
Making an External Page ..................................................................27
All Page ..............................................................................................27
Meet Me Page....................................................................................28
Call Park and Page ............................................................................28
Messages—Set and Cancel ..............................................................29
Returning Messages..........................................................................29
Programmed Messages ....................................................................30
CONVENIENCE FEATURES
Do Not Disturb ..................................................................................31
One Time DND ..................................................................................31
Mute ..................................................................................................31
Background Music ............................................................................31
Appointment Reminder/Alarm Clock ................................................32
Door Phone Calls ........................................................................32–33
Executive/Secretary Hotline ..............................................................33
Group Listening ................................................................................33
Account Codes ..................................................................................34
Locking Your Keyset ..........................................................................34
Off-Hook Voice Announce ................................................................35
OHVA Block ......................................................................................35
OHVA Reject ......................................................................................35
In Group/Out of Group ......................................................................35
CUSTOMIZING YOUR KEYSET
AME Password ..................................................................................37
Select Ring Tone................................................................................37
Change Your Passcode ....................................................................37
Set Answer Mode (Intercom) ............................................................38
Automatic Hold ..................................................................................38
Headset Operation ............................................................................38
Hot Keypad ........................................................................................39
Key Confirmation Tone ......................................................................39
Rejoining a Page ..............................................................................39
Ring Preference ................................................................................39
DISPLAY FEATURES
Interactive Display Keys ....................................................................40
Directory Information ...................................................................... 40
Dial by Directory ................................................................................41
Call Progress Displays ......................................................................41
Display Number Dialed......................................................................41
Call Duration Timer............................................................................41
Auto Timer..........................................................................................42
Timer Function ..................................................................................42
Viewing Message Indications............................................................42
Alarm Reminder Messages ........................................................42–43
Personal Speed Dial Names..............................................................43
Station Names ..................................................................................44
Managing Key Assignments .............................................................44
LCR with Clear ..................................................................................45
Caller ID........................................................................................46–49
PERSONAL SPEED DIAL NUMBERS
........50–51
ABOUT THIS BOOK
Your iDCS keyset is the most visible part of your telephone system. No matter what model keyset you are using telephone calls are handled the same
way. The 28D and 18D keysets have additional conveniences that are not
available to 8D keyset users. These are noted throughout this guide.
Please take the time to study this guide and to become familiar with the operation of your keyset. Keep this guide handy. You may need to look up instructions for infrequently used features.
Learning to use your keyset correctly will make everyday telephone communications a breeze.
This book is written based on the factory default settings for the feature
access codes. Sometimes, due to programming requirements, these codes
may be changed. If you find that a feature code does not work as described
in this book, please contact your installation and service company to determine the correct code.
1
THINGS YOU SHOULD KNOW
Your outside calls will light green on your keyset and red on other keysets.
You never lose sight of your calls while they are on hold. They stay right
where you put them and are identified with a green flashing light.
USER ORIENTATION
Some simple rules to remember:
iDCS telephones are called “keysets.” They contain buttons or “keys” that
are used to access or activate the many features of your office phone system. The keys with paper designation strips are programmable keys. This
means they can be programmed for a specific function on your keyset and
that same button can be something different on another keyset. See the system manager to get your most frequently used features assigned to your
programmable keys. When changes are made, be sure that your programmable keys are relabeled properly.
•
•
•
•
Lines from the telephone company are “C.O. lines.” Calls on these lines are
referred to as “outside calls.” Your system can have individual C.O. line keys
or lines may be assigned to groups. When they are in a group, you access
a line by dialing an access code or pressing a route button. For example, dial
9 or press a “LOCAL” key to get a local outside line. If Least Cost Routing is
used, pressing the “LCR” key will automatically select a preprogrammed
C.O. line according to what digits are dialed. Each line in the system is numbered, beginning with 701, then 702, 703, etc.
Direct Station Selection (DSS) keys are programmed to ring specific stations. You can press a DSS key instead of dialing the extension number. A
DSS key lights red when that station is busy (Busy Lamp Indication).
iDCS keysets provide distinctive ring patterns:
•
•
•
Outside calls have a single ring tone repeated.
Internal calls have a double ring tone repeated.
Door phone calls and alarm/appointment reminders have a triple ring
tone repeated.
CALL INDICATIONS
The keys on your phone have light emitting diodes (LEDs). These are tri-colored LEDs that light green, red or amber (green and red together).
Intercom calls, also called internal calls, always appear on your CALL buttons. They will always light green. You can have up to eight CALL buttons,
but at least two are recommended.
Any steady LED indicates the line or feature is in use.
A fast flashing green LED indicates a new call ringing in.
A slow flashing green or red LED indicates a call is on hold.
A slow flashing amber LED indicates a recall to your keyset.
SPEAKERPHONE
All iDCS keysets are speaker phones. Pressing the ANS/RLS key will answer
or release a call on the speakerphone. Switching from the handset to the
speakerphone is easy. Press the SPEAKER key and hang up the handset.
VOLUME CONTROLS
The iDCS keysets use the UP and DOWN keys to adjust the ringer volume
while the keyset is ringing, the speaker volume while the speakerphone is in
use and the handset volume while you are listening. These three levels will
be stored in memory until changed. If background music is turned on at your
keyset, the volume keys will also control the level of music. The volume of
pages heard through the speaker of a keyset can be adjusted during a page
announcement by using the volume keys. There are 16 levels for each volume setting. The volume of off-hook ring is controlled by a user-programmable setting.
TERMINAL STATUS INDICATOR
The terminal status indicator light is positioned on the top right corner of the
keyset above the display. The terminal status indicator is a tri-colored (red,
green, and amber) light that provides greater visibility of your keysets status
than the individual key LEDs. The terminal status indicator provides the following indications:
•
•
•
•
•
•
Busy/Off Hook
Intercom Ring
Outside Call Ring
Recall Ring
Message Waiting
Do Not Disturb
Steady Red
Flashing Red
Flashing Green
Flashing Amber
Flashing Red
Fast Flash Red at 1 Second Intervals
Outside calls appear on individual line keys if they are assigned. When an
individual line is not assigned to its own key, it will appear on a CALL button.
2
3
iDCS 28D KEYSET
FEATURE ACCESS CODES
This user guide is written based on the default access code for using system features. If the system numbering plan has been changed some of the
access codes may not be correct. Your installing company can inform you
of the correct codes.
32 CHARACTER DISPLAY
Two lines with 16 characters each.
TERMINAL STATUS INDICATOR
Used to provide your keyset status.
SYSTEM TONES
SOFT KEYS
Used to activate features
via the display.
The system provides several tones to assist you. Some of these tones are
already familiar to you.
Intercom Dial Tone—A steady tone that indicates you can begin dialing.
DIAL TONE
iDCS 28D
CONTINUOUS
Scroll
Ringback Tone—Indicates the station you dialed is ringing.
Call 1
Call 2
Message
SCROLL KEY
Used to scroll
through displays.
RINGBACK TONE—1000 ms ON/3000 ms OFF
CONTINUOUS
Busy Tone—Indicates the station you dialed is busy.
BUSY TONE—500 ms ON/500 ms OFF
CONTINUOUS
DND/No More Calls Tone—Fast busy tone indicates the station you
dialed is in the Do Not Disturb mode or cannot receive any more calls.
DND/NO MORE CALLS TONE—250 ms ON/250 ms OFF
FOR TEN SECONDS
1
2 ABC 3 DEF
4 GHI
5 JKL 6 MNO
7PQRS 8 TUV 9
SPEAKER
For handsfree operation and ringing.
Memory
Redial
WXYZ
Transfer Speaker
0OPER
Transfer/Conference Tone—Indicates your call is being held and you
can dial another party.
Volume
HOLD
ANS/RLS
TRANSFER/CONF TONE—100 ms ON/100 ms OFF
CONTINUOUS
Confirmation Tone—Very short beeps followed by dial tone indicate you
have correctly set or canceled a system feature.
CONFIRMATION TONE—50 ms ON/50 ms OFF
FOR ONE SECOND
(programmable)
Error Tone—A distinctive two level beeping tone indicates you have
done something incorrectly. Try again.
ERROR TONE—50 ms of tone 1/50 ms of tone 2
FOR THREE SECONDS
4
ANSWER/RELEASE KEY
MICROPHONE
For handsfree HOLD KEY
operation.
20 PROGRAMMABLE KEYS
WITH TRI-COLORED LIGHTS
Used for CALL buttons, intercom
calls, outside lines and many other
system features.
VOLUME CONTROL
KEYS Used to set independent levels for handset,
speaker, background
music, ring and page volumes.
8 PROGRAMMABLE KEYS WITH
TRI-COLORED LIGHTS Used to
call stations directly, to indicate
busy conditions of other stations,
for One Touch dialing and many
other system features.
5
iDCS 18D KEYSET
iDCS 8D KEYSET
32 CHARACTER DISPLAY
Two lines with 16 characters each.
32 CHARACTER DISPLAY
Two lines with 16 characters each.
TERMINAL STATUS INDICATOR
Used to provide your keyset status.
TERMINAL STATUS INDICATOR
Used to provide your keyset status.
SOFT KEYS
Used to activate features
via the display.
SCROLL KEY Used to
scroll through displays.
iDCS 8D
iDCS 18D
Scroll
Scroll
Call 1
Call 2
Message
SOFT KEYS Used to
activate features via the
display.
VOLUME
SCROLL KEY
Used to scroll
through displays.
Call 1
Call 2
Message
Transfer
Speaker
1
2 ABC 3 DEF
4 GHI
5 JKL 6 MNO
7PQRS 8 TUV 9
SPEAKER
For handsfree operation and ringing.
Memory
1
2 ABC 3 DEF
4 GHI
5 JKL 6 MNO
7PQRS 8 TUV 9
Redial
WXYZ
HOLD
HOLD
6
VOLUME CONTROL
KEYS Used to set independent levels for handset,
speaker, background
music, ring and page volumes.
ANS/RLS
ANS/RLS
ANSWER/RELEASE KEY
MICROPHONE
For handsfree HOLD KEY
operation.
10 PROGRAMMABLE KEYS
WITH TRI-COLORED LIGHTS
Used for CALL buttons, intercom
calls, outside lines and many other
system features.
WXYZ
0OPER
Transfer Speaker
0OPER
Volume
VOLUME CONTROL
KEYS Used to set independent levels for handset, speaker, background
music, ring and page volumes.
8 PROGRAMMABLE KEYS WITH
TRI-COLORED LIGHTS Used to
call stations directly, to indicate
busy conditions of other stations,
for One Touch dialing and many
other system features.
MICROPHONE
For handsfree operation.
SPEAKER
For handsfree operation and ringing.
HOLD KEY
ANSWER/
RELEASE KEY
8 PROGRAMMABLE KEYS WITH
TRI-COLORED LIGHTS Used to
call stations directly, to indicate
busy conditions of other stations,
for One Touch dialing and many
other system features.
7
iDCS 14B STRIP
ASSEMBLING YOUR KEYSET
14 PROGRAMMABLE KEYS
WITH RED LIGHTS Used to call
stations directly, to indicate busy
conditions of other stations, for
One Touch dialing and many other
system features.
•
Place the keyset face down on a flat surface.
•
Remove the base pedestal by placing your thumbs over the attachment
clips and press outward while simultaneously pressing down on the keyset body with your fingertips.
•
Plug the handset cord into the jack marked with the
•
Route the handset cord out the RIGHT side of the keyset as you look at
it face down.
•
Reattach the base pedestal.
•
Plug the line cord into the jack on the base of the keyset marked with the
symbol and route it through one of the cable channels in the bottom
of the base pedestal.
symbol.
iDCS KDB-FULL DUPLEX (FKDBF)
The standard speakerphone mode of operation for a iDCS keyset is “half
duplex”. This means that you cannot transmit and receive speech at the
same time. Adding a FKDBF to your keyset will convert the speakerphone
into full duplex mode enhancing its operation. In addition the FKDBF may
have up to three (3) external microphones attached to it for conference room
type applications. These microphones require an “EXTMIC” key programmed on the keyset to activate or deactivate them.
8
9
ADDING AN
iDCS 14 BUTTON KEY STRIP
OUTSIDE CALLS
MAKING AN OUTSIDE CALL
•
•
•
•
•
•
•
•
Place the keyset face down on a flat surface.
Remove the base pedestal by placing your thumbs over the attachment
clips and press outward while simultaneously pressing down on the
keyset body with your fingertips.
Remove the ribbon cable knockout from the bottom of the keyset.
Clip the 14 button strip to the side of the keyset.
Plug one end of the ribbon cable into the keyset and the other end into
the 14 button strip.
Place the support bracket over the ribbon cable and secure with the six
screws provided.
Reattach the base pedestal.
•
•
Lift the handset and press an idle outside line button, line group button
or dial a line access code to receive dial tone—OR—press an idle outside line button, line group button or dial a line access code to receive
dial tone through the speaker—OR—press SPEAKER, receive intercom
dial tone and dial a line access code.
Dial the telephone number.
Finish the call by replacing the handset or pressing the ANS/RLS key.
NOTE: You will receive No More Calls tone when you attempt to make a call
and there is no key available for that line.
•
•
•
If Least Cost Routing is enabled on your phone system, this button may
be labeled LCR or accessed by dialing an access code (usually 9).
If your system is programmed to require an authorization code before
making a call, dial 4 plus a valid code before selecting a C.O. line.
If your system is programmed to require an account code before making a call, press the ACCT button or dial 47 plus a valid bin number,
press the ACCT button again and then select a C.O. line.
For more information on authorization and account codes, see your system
administrator.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before dialing.
ANSWERING AN OUTSIDE CALL
•
Lift the handset and you are automatically connected to the ringing call.
See Ring Preference under Customizing Your Keyset—OR—press the
ANS/RLS key to automatically answer on the speakerphone.
NOTE: If a call is flashing at your keyset but not ringing, you must press the
flashing button to answer.
UNIVERSAL ANSWER
Outside lines may be programmed to ring a general alerting device. To
answer calls ringing this device, dial 67 or press the UA key. This device can
operate in any one of the six different ring plans.
REMOVE KNOCKOUTS
CONNECT RIBBON CABLE
10
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before dialing.
11
RECALL DIAL TONE
INTERCOM CALLS
Press the NEW button to disconnect your existing call, wait for dial tone and
then make a new call on the same line.
NOTE: If this button does not appear on your keyset, the FLASH key may
be programmed to recall dial tone.
SENDING A FLASH
While on an outside call, press the FLASH key to send a flash to the telephone company. This is required for some custom calling features or CENTREX use.
CALLING OTHER STATIONS
•
•
•
Dial the extension number or group number.
Wait for the party to answer. If you hear a brief tone burst instead of ringback tone, the station you called is set for Voice Announce or Auto
Answer. Begin speaking immediately after the tone.
Finish the call by replacing the handset or pressing the ANS/RLS key.
BUSY LINE QUEUING WITH CALLBACK
NOTES:
1. If you have a DSS key assigned to an extension or station group, you
may press this key instead of dialing the number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
If you receive a busy signal when you are selecting an outside line, this
means that the line or group of lines is busy.
ANSWERING INTERCOM CALLS
•
•
NOTE: Flash is not available on an ISDN circuit.
•
•
Press the CBK key, if programmed, or dial 44. You will hear confirmation
tone.
When the line becomes free, the system will call you back.
Lift the handset or press the ANS/RLS key to answer, wait for dial tone
and dial the telephone number or speed dial number again.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you
have set a callback, your CBK key will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before dialing.
•
When your keyset rings, simply lift the handset—OR—press the
ANS/RLS key to be connected to the calling station.
Finish the call by replacing the handset or pressing the ANS/RLS key.
See Ring Preference under Customizing Your Keyset.
VOICE ANNOUNCE MODE
[INTERCOM CALLS ONLY]
When another station calls you, your keyset will sound a brief attention tone
and you will hear the caller’s announcement.
•
Press ANS/RLS to turn on the microphone and speak handsfree—OR—
lift the handset to reply.
To finish the call, replace the handset or press the ANS/RLS key.
CANCELING CALLBACK
•
A callback will be canceled if not answered within 30 seconds. If you have
set a callback, your CBK key will light.
Note: In order for C.O. calls to be answered handsfree, AUTO ANS CO must
be set to ON.
Your phone may have a maximum of five callbacks to lines and/or stations
set at a time. To cancel a callback:
AUTO ANSWER MODE
•
When another station calls you, your keyset will sound a brief attention
tone and then automatically answer the call.
•
Press the CBK key, if programmed, or dial 44. You will hear confirmation
tone.
While you are listening to confirmation tone, press the HOLD key. This
will cancel the oldest set callback.
NOTES:
1. If the hot keypad feature is turned off, you must first lift the handset or
press the SPEAKER key before dialing.
12
•
•
[INTERCOM CALLS ONLY]
Your microphone and speaker are turned on and you can speak handsfree. For privacy, use the handset.
To finish the call, replace the handset or press the ANS/RLS key.
Note: In order for C.O. calls to be answered handsfree, AUTO ANS CO must
be set to ON.
13
BUSY STATION CALLBACK
CALLING YOUR SYSTEM OPERATOR
When you call another station and receive a busy signal:
•
•
•
•
•
Press the CBK key, if programmed, or dial 44.
When the busy station becomes free, your keyset will ring.
Lift the handset or press ANS/RLS to call the now idle station.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you
have set a callback, your CBK key will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before dialing.
Dial 0 to call your system operator or group of operators.
If you want to call a specific operator, dial that person’s extension number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
BUSY STATION CAMP-ON
When you call another station and receive a busy signal but you do not want
to wait for a callback:
MANUAL CAMP-ON
•
•
•
•
Press the CAMP key or dial 45.
The called station will receive off-hook ring tone repeated every few seconds and its first available CALL button will flash green to indicate your
call is waiting.
Wait for the called party to answer.
The called station must release its first call or place it on hold before
answering your camp-on.
NOTES:
1. If you receive No More Calls tone, that station has no available key to
accept your call. Hang up or leave a message.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before dialing.
14
15
CALL PROCESSING
SYSTEM HOLD
•
•
When you are connected to any call, press HOLD. The call will flash
green at your keyset. If this call appears on a line key at other keysets,
it will flash red at those keysets.
To take the caller off hold, press that key and the green flashing light will
go steady green again. Resume the conversation.
NOTE: While on a call, pressing a line key, route key or flashing CALL button will automatically put your first call on hold and connect you to the new
call. See Automatic Hold under Customizing Your Keyset.
EXCLUSIVE HOLD
To place an outside call on hold at your phone so that other users cannot get it:
•
•
Press the HOLD button twice. The call will flash green on your keyset
and this line will show a steady red light on other keysets.
To retrieve the call, press the flashing green line button or press the
HOLD button a third time.
NOTE: Intercom calls will always be placed on exclusive hold.
REMOTE HOLD
When you wish to place a call on hold at another station. Press TRANSFER
and a dial the station number (or press the appropriate DSS key). Press the
HOLD key. This will place the call on system hold on an available CALL button or Line Key at the remote station and return you to dial tone.
NOTES:
1. If the destination station does not have any free CALL buttons or line
keys you will hear No More Calls tone and must return to the other party
by pressing the TRANSFER key (or the RETURN soft key in the display).
2. Intercom calls cannot be remote held.
HOLD RECALL
If you leave a call on hold longer than the hold timer, it will recall your station. The button that the call appears on will have a slow flashing amber light.
•
16
When your phone rings, lift the handset or press the ANS/RLS key to answer the recall.
•
If you do not answer this recall within a pre-programmed period of time,
it will go to the system operator.
CONSULTATION HOLD
When you are talking on an outside line and it is necessary to consult with
another extension:
•
•
•
•
Press the TRANSFER key; you will receive transfer dial tone. Your call is
placed on transfer hold.
Dial the extension number.
Consult with the internal party.
Press TRANSFER to return to the outside party or hang up to transfer
the call.
NOTE: Repeatedly pressing the TRANSFER key will toggle between the
outside party and internal extension. If necessary you may disconnect either
one of the parties by pressing the DROP button.
RETRIEVING CALLS HELD AT
ANOTHER STATION
When a line is on hold and it appears on your keyset, press the line button
with the red flashing light.
When a line is on hold and it does not appear on your keyset, dial 12 plus
the line number or the extension number of the station that placed the call
on hold.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
CALL PARK
You can park an outside call in one of 10 “parking orbits”.
•
•
•
Press the PARK key and dial the orbit number required (0-9); the key
which the call was on will flash OR
Press the dedicated PARK key which will also flash.
To have the call picked up by another station notify the station user of
the parking orbit number
To pick up a parked call:
•
Press the PARK key followed by the orbit number required or press the
flashing PARK key.
17
TRANSFERRING CALLS
•
•
Transfer is used to send any call to another extension in one of two ways.
You can do a screened transfer by informing the other extension who is calling or you can do a blind transfer without notification.
CALL WAITING
•
•
While on a call, press the TRANSFER key and dial an extension number
or group number. Your call is automatically put on transfer hold. OR
Press a DSS key or station group key. Your call is automatically put on
transfer hold.
Hang up when you hear ringing (this is an unscreened or blind transfer).
OR
Wait for the called party to answer and advise him/her of the call and
hang up. If the transfer is refused, you will be reconnected to the outside
line when the called station hangs up or you can press TRANSFER to
return to the outside party. If you wish to send the call to another extension without waiting for the first station to hang up, simply press another DSS button. OR
Press the CALL button or C.O. line key to return to the outside party and
begin the transfer process again.
When you are transferring a call to a keyset set for Voice Announce or Auto
Answer, the transferred call will always ring.
NOTES:
1. After the inside party answers, you may alternate back and forth
between the parties by pressing the TRANSFER key.
2. If you receive No More Calls tone, that station has no key available to receive another call. Press TRANSFER to return to the other party.
3. You cannot transfer an Intercom call by pressing a DSS key. You must
press the TRANSFER key and dial the destination extension number.
TRANSFER WITH CAMP-ON
When you are transferring a call to another station and you receive a busy
signal, you may camp the call on to this station. Simply hang up when you
hear the busy signal. The called party will be alerted that a call is waiting for
them.
NOTE: If you receive No More Calls tone, that station has no key available
to receive another call. Press TRANSFER to return to the outside caller.
TRANSFER TO VOICE MAIL
This feature is used to send a call directly to a voice mailbox. Your keyset
must have a correctly programmed VT key to accomplish this. To transfer a
call directly to a voice mailbox:
18
While on a call, press the VT key and dial the mailbox number.
Hang up when dialing is completed.
If an outside call has been camped-on to your phone or another station has
camped-on to you:
•
•
•
Your keyset will ring and the call that is waiting for you (camped-on) will
flash green.
Press the flashing button to answer; your other call will go on hold automatically if your station has the Automatic Hold feature set. If not, you
must press HOLD and then the flashing button. OR
Finish the first call and hang up; the waiting call will ring.
Lift the handset or press the ANS/RLS key to answer.
NOTE: Intercom calls will not go on Automatic Hold.
CONFERENCE CALLS
You may conference up to five parties (you and four others) in any combination of outside lines and internal stations in any order.
•
•
•
•
While engaged in a conversation, press the CONF key and receive conference tone.
Make another call, either intercom or outside, press the CONF key and
receive conference tone.
Make another call or press the CONF key to join all parties.
Repeat the last step until all parties are added.
NOTE: When attempting to add another party to the conference and you are
not able to reach the desired person, hang up. Simply press the CONF key
again to return to your previous conversation.
To drop a party from your conference call:
•
•
Press CONF and dial the extension or line number that is to be dropped.
Press CONF again to reestablish the conference.
NOTE: To leave the conference, hang up. Control is passed to the next internal station. If there are no internal stations and you wish to leave outside
lines connected together in a trunk to trunk conference, press the CONF key
plus the CALL button that the call appears on or follow the instructions to
drop a party and use your extension number. When they hang up, the lines
will release automatically. Press CONF to rejoin a trunk to trunk conference.
19
FORWARDING CALLS
FORWARD BUSY/NO ANSWER
You may forward your calls to another station, group of stations or an external telephone number. Program a destination for the type of forwarding you
want as detailed below. If you have FWD ALL, FWD BUSY and FWD NO
ANSWER keys, press one to turn that forward feature on. A steady red light
reminds you what forward condition is activated.
If you have both a Forward on Busy destination and a Forward No Answer
destination programmed, you may set both of these at the same time:
You can clear all call forward conditions set at your station by lifting the handset and dialing 600.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
FORWARD ALL CALLS
•
•
Dial 604.
Receive confirmation tone and hang up.
FORWARD FOLLOW ME
To forward all your calls under any condition to another station:
When you want all calls to your extension forwarded to the extension where
you are now:
•
•
•
•
Dial 601 plus the extension or group number.
Receive confirmation tone and hang up.
Dial 605 plus your extension number.
Receive confirmation tone and hang up.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
2. The station that receives a Forwarded All call can transfer the call to the
forwarded station. This is useful when you are expecting an important
call but you do not wish to be disturbed by other calls.
3. When a station user places his/her keyset in Forward All mode and
he/she does not have a FORWARD ALL key, the TRANSFER key will
light to indicate Forward All has been set and calls to this station have
been transferred elsewhere.
If you want a specific extension's calls forwarded to your phone (Remote Call
Forward):
FORWARD BUSY
To forward outside calls to a number outside of your business, you must
have a FWD EXTERNAL button on your keyset.
To forward calls to another station when you are on the phone:
•
•
Dial 602 plus the extension or group number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press SPEAKER before you begin dialing.
FORWARD NO ANSWER
To forward calls to another station when you do not answer:
•
•
Dial 603 plus the extension or group number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
20
•
•
Dial 605 plus the desired extension number.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
FORWARD TO AN EXTERNAL NUMBER
•
•
•
•
•
While on-hook, press TRANSFER and then dial 102.
Dial 6.
Dial the outside line access code followed by the telephone number that
you want.
Press TRANSFER to store.
Press FWD EXTERNAL to turn the feature on and press it again to turn
the feature off.
NOTES:
1. External Call Forward will cancel all other call forwarding instructions.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
3. Intercom calls to your station may be forwarded to an external number
outside your business, if your installation company has enabled this feature.
21
FORWARD DND
DIALING FEATURES
To forward your phone when you activate DND.
•
•
Dial 607 plus the extension number or group number.
Receive confirmation tone and hang up.
NOTE:
1. If the Hot Keypad feature has been turned off you must first lift the handset or press the SPEAKER key before you begin dialing.
CALL FORWARD OPTIONS
A display keyset may review or change call forward options and destinations. Call forward access can be done via the keypad or by accessing the
keyset display features. To review or change call forward options:
•
•
•
•
•
Press TRANSFER 102.
Dial 0-6 to select the forward type (e.g., 1) OR
Press UP or DOWN to select the forward type
Press the right soft key to move the cursor
Dial the destination number (e.g., 202) OR
Press UP or DOWN to select the destination
Press the right soft key to move the cursor
Dial 1 to set OR
Press UP or DOWN to select YES or NO
Press TRANSFER to store and exit
STATION CALL PICKUP
To pick up (answer) a call ringing at another station, lift the handset and dial
65 plus the extension number of the ringing phone.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
GROUP CALL PICKUP
To pick up (answer) a call ringing in any pickup group, lift the handset and
dial 66 plus the desired group number 01–08 or press the flashing GROUP
PICKUP key if available.
NOTES:
1. A group pickup key can have an extender for a specific pickup group.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before dialing the access code.
22
SPEED DIALING
You can dial a preprogrammed telephone number stored in the system-wide
speed dial list of numbers 500–799 or from your personal list of numbers
00–49:
•
•
•
With the handset on-hook, press the MEMORY key or dial 16.
Dial the desired speed dial number.
The telephone number is automatically dialed for you.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
PROGRAMMING PERSONAL SPEED
DIAL NUMBERS
You can program frequently dialed telephone numbers in a personal speed
dial list. A station may be assigned up to fifty numbers, 00–49. See your system administrator to determine the amount assigned to your station.
•
•
•
•
•
While on-hook, press TRANSFER and then dial 105.
Dial a speed dial number (00–49).
Dial a line or line group access code.
Dial the telephone number to be stored (24 digits maximum). It can include #, 4, FLASH and PAUSE.
Press TRANSFER to store the number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
For the purposes of programming speed dial numbers, the programmable
keys are known as A, B, C, D, E and F and are defined below.
28D KEYSET
18D KEYSET
DEFAULT
PROGRAMMING
KEYS LAYOUT
A
B
C
D
E
F
Transfer Speaker
8D KEYSET DEFAULT
PROGRAMMING
KEYS LAYOUT
VOLUME
Transfer
A
C
E
B
D
F
Speaker
23
•
•
•
•
•
•
•
The A key is not used.
The B key inserts a flash.
The C key inserts a pause.
The D key is used for pulse to tone conversion. If your system uses
rotary (or pulse) dialing C.O. lines, pressing D while entering a speed
dial number causes all subsequent digits to be sent as DTMF tones.
The E key is used to hide digits. Display keyset users may want to hide
some speed dial numbers so that they will not show in the display. When
you are entering a telephone number, press E. All subsequent digits will
be hidden. Press E again to begin displaying digits.
The F key is used to enter a name. See Personal Speed Dial Names
under Display Features.
Use the HOLD key to clear a speed dial number.
SAVE NUMBER WITH REDIAL
To save the number you just dialed for later use, press the SNR key before
hanging up.
To redial this saved number at any time, press the SNR key or dial 17. The
same line will be selected for you.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
2. The saved telephone number is stored in memory until you save another number.
3. Redial does not apply to intercom calls.
ONE TOUCH SPEED DIALING
CHAIN DIALING
You may assign any speed dial number to an already existing One Touch
Speed Dial button for quick and easy dialing of frequently used numbers.
You may manually dial additional digits following a speed dial number or
chain as many speed dial numbers together as required:
•
•
•
•
•
While on-hook, press TRANSFER and then dial 107.
Press a One Touch Speed Dial button.
Dial the speed dial number (00–49 or 500–799) that you want assigned
to this button.
Press TRANSFER to store your selection.
To call this telephone number, just press the One Touch Speed Dial button.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
LAST NUMBER REDIAL
After the first speed number is dialed, press MEMORY again and dial another speed number OR manually dial additional digits following a
speed dial number.
AUTOMATIC REDIAL/RETRY
When you are making an outside call and you receive a busy signal, the system can automatically redial the number for you. It will automatically redial at
a pre-programmed interval for up to 15 attempts.
•
•
When you hear a busy signal, press the RETRY button.
The system will reserve the line and automatically redial the same number for you. You will hear the call being made through the keyset speaker. The microphone is muted.
When the called party answers, lift the handset or press the flashing
SPEAKER to begin speaking.
To redial the last telephone number you dialed, press the REDIAL key or dial
19.
•
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
2. Redial does not apply to intercom calls.
NOTES:
1. If you make another call, auto-redial is canceled.
2. To cancel a retry, lift and replace the handset.
24
25
PULSE TO TONE CHANGEOVER
PAGING AND MESSAGING
When making an outside call on a dial pulse line, press #. All digits dialed
after the # with be sent as tones.
MAKING AN INTERNAL PAGE
To make an announcement through the keyset speakers:
•
•
•
•
Lift the handset.
Press the PAGE key or dial 55.
Dial the desired zone number 0, 1, 2, 3 or 4.
After the attention tone, make your announcement.
NOTE: If you have a dedicated page zone key, it is not necessary to press
PAGE and dial a zone number.
MAKING AN EXTERNAL PAGE
To make an announcement through the external paging speakers:
•
•
•
•
Lift the handset.
Press the PAGE key or dial 55.
Dial the desired zone number 5
OR
Dial 9 to page all external zones.
After the attention tone, make your announcement.
NOTE: If you have a dedicated page zone key, it is not necessary to press
PAGE and dial a zone number.
ALL PAGE
To page all designated keysets and external speakers at the same time:
•
•
•
•
Lift the handset.
Press the PAGE key or dial 55.
Dial 4 or press the ALL PAGE key.
After the attention tone, make your announcement.
NOTE: The LED on the PAGE key will only light when an All Page is in
progress.
26
27
MEET ME PAGE
SETTING A MESSAGE INDICATION
•
•
•
•
•
•
•
When you are calling another station and no one answers or you receive a
busy signal, you can leave a message indication:
Lift the handset.
Press the Meet Me Page (MMPG) key or dial 54.
Dial the desired zone number.
After the attention tone, instruct the paged person to dial 56.
Press WAIT or TRANSFER.
Remain off-hook until the person dials 56 from any phone.
The paged person will be automatically connected with you.
CALL PARK AND PAGE
When you have an outside call for someone who is not at his/her desk, you
can park the call prior to paging.
To retrieve a parked call from orbit:
• Press the PARK button and dial the announced orbit number (0-9).
• You will be connected to the parked call.
NOTES:
1. You must have a PARK button or park access code to retrieve and place
calls in park orbits.
2. If the parked call is not retrieved within a pre-programmed period of time,
it will recall your keyset and have a slow flashing amber light. You cannot park and page intercom calls.
3. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
•
•
NOTES:
1. A station can have up to five message indications.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
CANCELING MESSAGES
To cancel a message indication that you left at another station, dial 42 plus
the extension number of the station at which you left a message.
To cancel all message indications left at your keyset, dial 42 plus your extension. Your MESSAGE light will go out.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key before you begin dialing.
RETURNING MESSAGES
•
AUTOMATIC PARK WITH PAGE KEY
•
•
•
To
•
•
While in conversation, press the PAGE button. The call is automatically
parked at your station.
Receive page tone and dial a desired page zone number.
Make announcement indicating your extension number or the line number. Hang up.
retrieve an automatically parked call:
Dial 10 plus the number that was announced. If you have a PAGPK key,
press it and dial the number that was announced. If you have a PARK
key, press it and dial the announced orbit number.
You will be connected to the parked call.
NOTES:
1. If the call is not retrieved within a pre-programmed period of time, it will
recall your keyset and have a slow flashing amber light. You cannot park
and page intercom calls.
3. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
28
Press the MESSAGE key or dial 43 and receive confirmation tone.
Hang up. The MESSAGE key on the called station will light. Standard
telephones receive special dial tone as a message indication.
•
•
Press the MESSAGE key or dial 43. The first station that left a message
will be called automatically. If that station does not answer, your MESSAGE light will stay on.
Repeat until all messages have been returned in the order received.
Your MESSAGE light will turn off when all messages have been returned.
NOTES:
1. Display keyset users can view message indications and return them in
any order. See Viewing Message Indications under Display Features.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
3. If a message has been left at your keyset by a keyset in Auto Answer,
you must manually cancel the message after it has been returned.
29
PROGRAMMED MESSAGES
When you will be away from your phone for any length of time, you can leave
a programmed station message. Display stations calling you will see this
message and be informed of your status or follow your instructions.
•
•
•
Dial 48 plus any of the message codes (01–30) listed on the back of this
user guide.
To cancel any of these messages you might have selected, dial 48 plus
00.
Press TRANSFER to exit and store your selection.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key.
You can have multiple programmed message keys (PMSG) and each one
can have a different message code:
•
•
Press any programmed message (PMSG) button. The message is set
and the button will light red. Press the button again to turn off.
Pressing another programmed message (PMSG) button will turn the
previous one off and set a different programmed message.
CONVENIENCE FEATURES
DO NOT DISTURB
Use this feature when you want to block calls to your keyset.
•
•
While on-hook, press the DND key or dial 401. The DND key lights
steady red to remind you of this mode.
To cancel DND, press the DND key again or dial 400. The DND light
turns off. You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key.
2. If you place your keyset in DND mode and you do not have a DND key,
your TSI key will flash to indicate DND status.
ONE TIME DND
If you are on a call and you do not wish to be interrupted while on that call,
you can press the DND key and place your station in Do Not Disturb. When
you hang up at the end of the call, DND will be automatically canceled and
your keyset will be able to receive new calls. This feature requires a DND
key.
MUTE
You can mute the handset transmitter or the microphone during any conversation:
•
•
Press the MUTE key. It will light red.
To resume speaking, press the MUTE button again. The light turns off.
BACKGROUND MUSIC
When a music source is supplied, you may listen to music through the
speaker in your keyset:
•
•
While on-hook, press the HOLD button to hear music.
Press the HOLD button again to turn music off.
You can set the level of background music by using the VOLUME keys while
listening to the music. This does not affect the speakerphone level.
30
31
APPOINTMENT REMINDER/ALARM
CLOCK
CALLING THE DOOR PHONE/ROOM
MONITOR
This feature works like an alarm clock. Use it to remind yourself of an appointment later in the day (TODAY ONLY) or as a daily reminder every day
(DAILY). You can set up to three alarms. Each one can be either a TODAY
ONLY or a DAILY alarm.
You may call the door phone and listen to what may be happening outside
or in another room.
When the alarm rings, you will hear three short rings repeated three times.
Lift the handset to answer the alarm. If you do not, the alarm will alert you
two more times at five minute intervals.
To set alarms:
•
•
•
•
•
•
Press TRANSFER and then dial 112.
Dial the alarm number 1 or 2.
Dial the time at which you want the alarm to sound. Enter the time as
HHMM (hours and minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY ONLY) or 2 (DAILY) to select the alarm type.
Press TRANSFER to save.
Repeat for each alarm if needed.
•
•
•
Dial the extension number of the door phone.
You will be connected to the door phone and you can listen or have a
conversation.
If an electric door lock release is installed, dial 13 to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKER key.
EXECUTIVE/SECRETARY HOT LINE
If programmed, an executive and a secretary can have a hot line between
them. When the executive station is in the DND mode, all of its calls will ring
the secretary station.
•
Either person can press the BOSS key to make a voice call to the other
station.
Using the hot line will override DND at the other station. This key will light
red when the other station is in use.
To cancel individual alarms:
•
•
•
•
To transfer a call to a Boss in DND:
Press TRANSFER and then dial 112.
Dial alarm number 1 or 2.
Press the HOLD key.
NOTE: Display keysets can show a reminder message. See Alarm Reminder Messages under Display Features.
ANSWERING THE DOOR PHONE
/ROOM MONITOR
•
•
•
Press the TRANSFER key followed by the BOSS key.
Wait for the BOSS to answer to announce the call and hang up to complete the transfer OR
Hang up to complete a blind transfer after pressing the BOSS key.
GROUP LISTENING
When you are programmed to receive calls from a door phone:
When you are engaged on a call and you are using the handset, you may
want other people to hear the distant party’s voice over the speaker:
•
•
•
•
You will receive three short rings repeated.
Lift the handset or press ANS/RLS key. You are connected to the door
phone.
If an electric door lock release is installed, dial 13 to unlock the door.
•
•
Press the LISTEN key to turn on the speaker. The microphone is not in
use, so the distant party does not hear other parties present in your office.
Press LISTEN again to turn the speaker off and resume private conversation.
Repeat if necessary.
NOTE: Depending on speaker volume and the acoustics of your office, it
may be advisable to turn the group listening feature off before hanging up.
This will eliminate a momentary squeal.
32
33
ACCOUNT CODES
OFF-HOOK VOICE ANNOUNCE
When equipped with optional equipment, your system will allow calls to be
charged to a specific account:
Keysets may receive a voice announcement while on another call. The calling station must have an OHVA key. When you are in DND, you cannot
receive OHVA calls. The OHVA feature will work with intercom and transferred calls.
•
•
During any outside C.O. call, press the account (ACCT) key.
Enter the account code (maximum 12 characters including 4 and #).
Press the ACCT key again. Your conversation will not be interrupted.
NOTE: If you make an error before you complete the account code, press
the ACCT key twice and redial the correct code. Only the last account code
dialed will be printed.
LOCKING YOUR KEYSET
You can lock your keyset to control misuse of your phone while you are
away. You can unlock it when you return. Your default station passcode is
1234.
0
UNLOCKED
1
LOCKED
OUT GOING
2
LOCKED
ALL CALLS
Make outsid e calls
YES
NO
ACCESS DENIED
NO
Receive outsid e calls
YES
YES
NO
Make intercom calls
YES
YES
NO
Receive intercom
calls
YES
YES
NO
•
•
•
•
While on-hook, press TRANSFER and then dial 100.
Dial your four digit station passcode.
Dial 1 to locking outgoing, 2 for locked all calls, or 0 to unlock.
Press TRANSFER to store your selection.
To make an off-hook voice announcement:
•
•
•
•
•
•
Dial the extension number or press the DSS key.
When you receive a busy signal, press the OHVA key.
After the attention tone, begin speaking.
Finish the call by replacing the handset or pressing the ANS/RLS key.
Press the flashing CALL button on your keyset. This will place the original party on hold and allow you to talk to the announcing party.
To return to your first party, press the key corresponding to your original
call. This will disconnect the OHVA call.
When you receive an OHVA, if you are using the handset, you will hear the
announcement in the handset receiver. If you are using the speakerphone
the announcement will always be heard through the speaker.
NOTES:
1. When you are voice announcing to a station close to you, use the handset to avoid an echo effect.
2. You cannot off-hook voice announce to single line telephones.
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (BLOCK) key. Pressing this key will prevent anyone from making an OHVA to you until you press
the button again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (REJECT) key. Pressing this key while receiving an OHVA call will disconnect the voice announcing party and return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group, you can remove your keyset from the group and then put it back in. While you are out of the group,
you can receive calls to your extension number but not calls to the group
number. If you have an IN/OUT key:
•
34
Press the IN/OUT key. It will light red when your keyset is in the group.
35
•
Press the IN/OUT key again to exit the group and turn the light off. Repeat as necessary.
CUSTOMIZING YOUR KEYSET
If you do not have an IN/OUT key:
•
Dial 53 plus the group number. Repeat as necessary plus 0 to exit the
group or 1 to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press SPEAKER key.
The IN/OUT key can include an extender to indicate the specific group that
this key will affect. This means that if you are in multiple groups, you can decide for which groups you will receive calls.
AME PASSWORD
This feature allows people using the AME (Answer Machine Emulation) feature to enable password protection. This will prevent unauthorized people
from listening to your messages being left. The passcode is the same as
your station passcode. This feature only applies if there is a Samsung Voice
Mail card installed in the system and your keyset has a programmed AME
key. See the Keyset User Features in the SVMi guide.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 101 to turn on AME PASSCODE or 100 to turn it off.
Press TRANSFER to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
•
•
While on-hook, press TRANSFER and then dial 111.
Dial 1–8 or press the UP and DOWN keys to hear each tone.
When you hear the tone that you prefer, press TRANSFER to save it.
NOTE: Specific lines or stations may be programmed to ring with a different tone than what you have selected for your keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234. You can change your station passcode whenever you desire.
•
•
•
•
•
36
While on-hook, press TRANSFER and then dial 101.
Dial your old passcode.
Dial a new passcode (must be four characters). You can use 0–9.
Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
Press TRANSFER to store the new passcode.
37
SET ANSWER MODE (INTERCOM)
HOT KEYPAD
You can receive internal calls in one of three modes (see Answering
Intercom Calls under Intercom Calls for descriptions):
On your phone system your keyset’s keypad can be made “live” or “hot” so
that it is not necessary to lift the handset or press the SPEAKER key before
you begin dialing. Calls can be made and features activated by simply dialing the C.O. line number, trunk group access code, intercom number or feature access code. To activate this feature:
•
•
•
While on-hook, press TRANSFER and then dial 103.
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
Press TRANSFER to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have
Forward No Answer (FNA) turned on, you must answer screened transfers
by pressing the ANS/RLS key before your FNA timer expires or the call will
forward.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing CALL
button will automatically put your call on hold and connect you to the next
call. This feature can be turned on or off at your keyset.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 01 to turn Automatic Hold on or 00 to turn it off.
Press TRANSFER to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing TRANSFER.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When
using headset mode, press the ANS/RLS key to answer and release calls.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 21 to use the headset or 20 to use the handset.
Press TRANSFER to store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this key while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the key while the
light is lit will cause the keyset to return to handset mode and the light will
go out.
38
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 31 to turn the Hot Keypad on or 30 to turn it off.
Press TRANSFER to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button
on the dial pad. This tone can be turned on or off.
•
•
•
While on-hook, press TRANSFER and then dial 110.
Dial 40 to turn tones off or 41 to turn tones on.
Press TRANSFER to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal
page after you return your keyset to idle. To enable this feature:
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 51 to turn this feature on or 50 to turn it off.
Press TRANSFER to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or
press the ANS/RLS key. This method will always answer calls in the order
they arrived at your keyset. When you turn ring preference off, you must
press the flashing button to answer a call, allowing you to answer calls in the
order you choose.
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 61 to turn ring preference on or 60 to turn it off.
• Press TRANSFER to store your selection.
39
DISPLAY FEATURES
INTERACTIVE DISPLAY KEYS
The three keys below the display are substitutes for dedicated feature keys
and access codes. Pressing one of these keys has the same effect as pressing a programmable key. These keys are called soft keys as their functions
are not fixed. They change to present you with the best options for that call
condition. The use of soft keys allows the programmable keys to be used for
more DSS and speed dial keys.
The SCROLL key is used to display options available to the user at a particular time or during a specific procedure. Press this key once while in the idle
state to view the three main categories available.
201: STN NAME
CALL OTHER ANS
ANSWER: Guides you through the options to answer calls.
OTHER: Guides you through features other than making or answering calls.
CALL: Guides you through the options to make a call.
Select one of the main categories: CALL, OTHER or ANS (ANSWER). Press
the SCROLL key to display additional options available under each of the
three main categories. The symbol ° displayed as the last character on the
lower line of the display indicates that there are additional options. Press the
SCROLL key to display these additional options.
User instructions will be displayed in lower case letters. Options assigned to
soft keys will be in upper case letters.
DIRECTORY INFORMATION
An 11 character directory name can be assigned to each extension number.
Display keyset users can view the name of the called or calling station before
answering.
Each outside line can have an 11 character directory name. Incoming calls
can be easily identified and answered with different greetings.
Outside and internal calls ringing to a station group will display [CALL FOR
xxx] where xxx is the station group number. This allows you to answer calls
directed to you differently than calls directed to your group.
40
DIAL BY DIRECTORY
Each station or speed dial number can have an associated directory name.
A station or speed dial number can be selected by scrolling alphabetically
through a directory name list. This on-line “phone book” allows the user to
look up and dial any station or speed dial number in seconds.
•
•
•
•
•
Press the DIR key (DIRECTORY).
Select the directory you wish to use: PERS (personal speed dial numbers), SYS (system speed dial numbers) or STN (station names).
Dial the key on the keypad that corresponds to the first letter of the name
you wish to search for.
Use the UP and DOWN arrows to scroll through the names.
Press the DIAL soft key to dial the number.
NOTE: A DIR key can have an extender to take you directly to one of the
above lists (PERS, SYS, or STN).
CALL PROGRESS DISPLAYS
During everyday call handling, your keyset display will provide information
that is helpful and in some cases invaluable. Displays like [CALL FROM 203],
[TRANSFER TO 202], [701: RINGING], [TRANSFER FM 203], [708 busy],
[Camp on to 204], [Recall from 204], [Call for 501], [message frm 204] and
[FWD ALL to 204] keep you informed of what is happening and where you
are. In some conditions you are prompted to take an action and in other
cases you receive directory information.
DISPLAY NUMBER DIALED
Display keysets begin showing digits as they are dialed. They will stay in the
display until the call duration timer comes on automatically or the TIMER
button is pressed. If the call duration timer is not used, the number dialed will
be displayed until the call is released, transferred or put on hold.
CALL DURATION TIMER
The system can be set to automatically time outside calls. A few seconds
after you dial a telephone number, the timer appears in the display. It
appears immediately for incoming calls. The call timer continues for the duration of the call. Call duration times are displayed in minutes and seconds.
If a call lasts longer than 60 minutes, the timer restarts.
You can press the TIMER key to manually begin timing a call. Press it again
to stop timing. If you press it while the automatic timer is on, the call duration time is restarted.
41
AUTO TIMER
COUNT
1
2
3
4
5
Display keyset users may have the timer automatically start when they
answer incoming calls or after a short delay on an outgoing call.
DIAL 0
<
>
.
)
0
DIAL 1
space
?
,
!
1
DIAL 2
A
B
C
@
2
DIAL 3
D
E
F
#
3
DIAL 4
G
H
I
$
4
DIAL 5
J
K
L
%
5
DIAL 6
M
N
O
^
6
DIAL 7
P
Q
R
S
7
VIEWING MESSAGE INDICATIONS
DIAL 8
T
U
V
4
8
You can view all of your message indications before you return them:
DIAL 9
W
X
Y
Z
9
•
•
•
DIAL 4
:
=
[
]
4
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 11 to turn the auto timer on or 10 to turn it off.
Press TRANSFER to store your selection.
TIMER FUNCTION
Display keyset users may use this feature as a simple stopwatch.
•
•
•
•
•
When the keyset is idle, press the TIMER button to start timing.
Press the TIMER button again to stop timing.
Read the elapsed time in the display.
Lift the handset and replace it. The display will return to date and time.
With the handset on-hook, press the MSG key with the red flashing light.
The first station that left a message indication will be displayed.
Press the UP and DOWN arrows to scroll through the stations that left
message indications. Use the soft keys to reply, clear or advance to the
next message.
Press the ANS/RLS key to return your keyset to the idle condition.
NOTES:
1. When the character you want appears on the same dial pad key as the
previous character, press UP to move the cursor one space to the right.
2. Other symbols are available for DIAL #.
ALARM REMINDER MESSAGES
To cancel an individual alarm and reminder message:
When you use the alarm/appointment reminder feature, you create a 16
character reminder message. When the alarm rings, your message will appear instead of [ALARM REMINDER]. To program reminder messages:
•
•
•
•
•
•
•
PERSONAL SPEED DIAL NAMES
•
•
•
•
42
Press TRANSFER and then dial 116.
Dial the alarm number 1 or 2.
Dial the time you want the alarm to go off. Enter the time as HHMM
(hours and minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY) or 2 (DAILY) to select the alarm type.
Write your message using the dial pad keys. Each press of a key selects
a character. Pressing the next key moves the cursor to the next position.
For example, if your message is “TAKE MEDICATION,” press 8 once to
get the letter “T.” Press 2 once to get “A.” Press 5 twice to get “K.” Continue selecting characters from the following table to complete your
message.
Press the TRANSFER key to store the alarm and reminder message.
Repeat for each alarm if needed.
Press TRANSFER and then dial 112.
Dial alarm number 1 or 2.
Press the HOLD key.
Press the TRANSFER key.
Each personal speed dial number can have an 11 character name assigned
to it. This name is used to select the speed dial bin when you are dialing by
directory.
•
•
•
•
•
Press TRANSFER and then dial 106.
Dial the speed dial bin number 00–49.
Write your message using the procedure described in Alarm Reminder
Messages.
Press the TRANSFER key to store the speed dial name.
Repeat for each speed dial bin if necessary.
43
STATION NAMES
LCR WITH CLEAR
You can assign an 11 character name to your keyset. This allows other display keyset users to call you using the directory dial feature.
When you are making an outside call using LCR and dial an incorrect digit,
you can press the CLEAR soft key to reenter the telephone number. You do
not need to redial 9 to reaccess LCR.
To program a station name:
•
•
•
Press TRANSFER and then dial 104.
Enter the 11 character name using the procedure described in Alarm Reminder Messages.
Press TRANSFER to store the name.
MANAGING KEY ASSIGNMENTS
You can view your key assignments and add extenders to some of your programmable keys for easy one touch operation of frequently used features.
An extender is a number that makes an otherwise general key very specific.
Adding the digit “4” to a PAGE key defines this key for paging zone four.
Adding “225” to a different pickup key will define this key as pickup for extension 225 only. The key must already be assigned by the technician.
•
•
•
•
While on-hook, press TRANSFER and then dial 107.
Use the VOLUME keys to scroll through all of your programmable keys
OR
Press the programmable key to which you want to add the extender.
When you reach a key listed below, dial the corresponding extender.
Press TRANSFER to store and exit programming.
KEY
DESCRIPTION
EXTENDER
BOSS . . . .Boss/Secretary . . . . . . . . .1–4
DP . . . . . . .Direct Pickup . . . . . . . . . .Extension or station group number
DS . . . . . . .Direct Station . . . . . . . . . .Any extension number
FWRD . . . .Call Forward . . . . . . . . . . .0–5
GPIK . . . . .Group Pick-Up . . . . . . . . .01–08
IG . . . . . . .In/Out of Group . . . . . . . .Any group you are part of 5XX
MMPG . . . .Meet Me Page . . . . . . . . .0–5, 4
PAGE . . . .Page . . . . . . . . . . . . . . . . .0–5, 4
PSMG . . . .Programmed Message . . .01–20
SG . . . . . . .Station Group . . . . . . . . . .5XX
SPD . . . . . .Speed Dialing . . . . . . . . . .00–49, 500–799
DIR . . . . . .Directory . . . . . . . . . . . . . .PERS (1), SYS (2) or STN (3)
VT . . . . . . .Voice Mail Transfer . . . . . .Voice Mail Group (5XX)
NOTE: Confirm that the cursor is placed correctly before you enter the extender.
44
45
CALLER ID
NO CID DSP
WHAT IS CALLER ID?
Caller ID is the name given to the telephone company-provided feature that
delivers the telephone number and sometimes the name of the person calling your phone. There are two types of Caller ID; the first delivers the calling
party’s telephone number only and the second (sometimes referred to as
“Deluxe” Caller ID) delivers both the calling party’s telephone number and
name as listed in the telephone directory.
The phone system can handle both types of Caller ID; in fact, in the case of
number only delivery, the system can be programmed to insert a name for a
specific telephone number. However, even though you are paying to receive
Caller ID information, there are some circumstances that mean you will not
receive this information. The six most common reasons are listed below
along with the display information that the system will provide.
PRIVATE
OUT OF AREA
PAYPHONE
The caller does not wish his/her name or number to be
revealed to you. This type of call can be stopped at the
telephone company by dialing an access code on your
outside lines. This will redirect these PRIVATE calls to an
announcement that states that you do not wish to receive calls that have had Caller ID blocked. The code to
block these calls can usually be found in the front section of the telephone directory.
The caller is calling from an area that cannot provide
Caller ID information (for example, international calls) or
he/she is calling from a type of circuit that cannot provide Caller ID information, for example, some outbound
WATS lines.
The caller is calling from a coin-operated telephone. The
telephone company will send this information as there
are no directory listings for pay phones. The number will
be delivered as usual.
INVALID CID INFO This is a message that will be displayed when CID information is sent on the line but was somehow corrupted.
Caller ID Digital Signal Processors (CIDDSP’s) are
resources in the iDCS system required for receiving CID
data. If there are no CIDDSP’s available at the time a
call comes in, this is the message you will see on your
display.
NOTE: The Caller ID features require optional software and/or hardware.
Please see your service and installation company for details.
SELECTING YOUR CALLER ID
DISPLAY
You can decide if you want to see the Caller ID name or Caller ID number in
the display. Regardless of which one is selected, you can press the NND
key to view the other pieces of Caller ID information. To select the type of
Caller ID information you wish to view first:
•
•
•
•
With the handset on-hook, press TRANSFER and then dial 119.
Dial 0 for CID options, 1 for ANI options, or 2 for CLI options.
Dial 0 if you do not wish to view CID information, 1 to view the NUMBER
first or 2 to view the NAME first.
Press TRANSFER to exit and store your selection.
VIEWING THE NEXT CALLER ID CALL
In the event that you have a call waiting or a camped-on call at your keyset,
you can press the NEXT key to display the Caller ID information associated
with the call in queue at your keyset. Either the CID name or CID number will
show in the display depending on your Name/Number selection.
To view Caller ID information for calls that have been camped-on to your
keyset, press the NEXT key. If your keyset does not have a NEXT key, press
the CID key and then the NEXT soft key.
SAVING THE CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may
press the SAVE key to save the CID number. If your keyset does not have a
SAVE key, press the CID key, the SCROLL key and then the SAVE soft key.
The system must be using LCR to dial the saved number.
NO CID RECEIVED This is a message that will be displayed when there was
no CID information sent on the line.
46
47
REDIALING A SAVED CALLER ID
NUMBER
•
•
To redial a number that has been saved, press the SNR key or dial 17.
NOTES:
1. Your telephone system must have LCR correctly programmed to redial
the saved number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
STORING A CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may
save the CID number as a speed dial number in your personal speed dial
list. To store a Caller ID number in a personal speed dial bin:
•
•
•
•
Press the STORE key. The system displays the speed dial bin in which
the number was stored, OR
Press the CID key and then press the SCROLL key.
Press the STORE soft key.
The system displays the speed dial bin in which the number was stored.
NOTE: Your telephone system must have LCR correctly programmed to redial the saved number. If LCR is not being used on your system, you will not
be allowed to STORE CID numbers.
INQUIRE CALLER ID PARK/HOLD INFO
If you are informed that an incoming call is on hold or has been parked for
you, you may view the Caller ID information before you retrieve the call. This
may influence how you choose to handle the call.
From an idle keyset:
•
•
•
Dial the trunk number.
You may now answer the call by pressing the ANS key, OR
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
NOTES:
1. If you are on an intercom call or you have Automatic Hold turned off, you
must finish the existing call or place it on hold before inquiring.
2. If you inquire about an outgoing call, you will receive a [call no longer
available] display.
REVIEWING PAST CALLER ID CALLS
This feature allows you to review CID information for calls sent to your keyset. This list can contain 10–50 calls in a last-in, first-out basis. The list includes calls that you answered and calls that rang your keyset but that you
did not answer. When reviewing this list, you can press one button to dial
the person back. The system must be using LCR to dial the stored number.
To access the CID information stored in your REVIEW list:
•
•
•
Press the REVIEW key, OR
Press the CID key and then press the REVIEW soft key.
If you have entries in your review list, the most recent call will be shown
first.
You can now CLEAR this entry, OR
Use NND to view more information about this call, OR
Press DIAL to call this person back, OR
Press SCROLL and then press STORE to save this number in a personal speed dial bin.
NOTES:
1. Each keyset defaults with ten review bins. Please see your system administrator to determine the number of bins assigned to your keyset.
2. Your system must have LCR correctly programmed to allow you to DIAL
numbers from the review list or to STORE entries from the review list.
Press the INQUIRE key, OR
Press the CID key and then the INQUIRE soft key.
Dial the trunk number.
You may now answer the call by pressing the ANS key, OR
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
If you are on a call:
•
48
Press the INQUIRE key. Your existing call will go on hold, OR
Press the CID key and then the INQUIRE soft key to place the first call
on hold.
49
PERSONAL SPEED DIAL NUMBERS
PERSONAL SPEED DIAL NUMBERS
CODE
NAME
TELEPHONE NUMBER
CODE
NAME
TELEPHONE NUMBER
00
_________________________
_________________________
25
_________________________
_________________________
01
_________________________
_________________________
26
_________________________
_________________________
02
_________________________
_________________________
27
_________________________
_________________________
03
_________________________
_________________________
28
_________________________
_________________________
04
_________________________
_________________________
29
_________________________
_________________________
05
_________________________
_________________________
30
_________________________
_________________________
06
_________________________
_________________________
31
_________________________
_________________________
07
_________________________
_________________________
32
_________________________
_________________________
08
_________________________
_________________________
33
_________________________
_________________________
09
_________________________
_________________________
34
_________________________
_________________________
10
_________________________
_________________________
35
_________________________
_________________________
11
_________________________
_________________________
36
_________________________
_________________________
12
_________________________
_________________________
37
_________________________
_________________________
13
_________________________
_________________________
38
_________________________
_________________________
14
_________________________
_________________________
39
_________________________
_________________________
15
_________________________
_________________________
40
_________________________
_________________________
16
_________________________
_________________________
41
_________________________
_________________________
17
_________________________
_________________________
42
_________________________
_________________________
18
_________________________
_________________________
43
_________________________
_________________________
19
_________________________
_________________________
44
_________________________
_________________________
20
_________________________
_________________________
45
_________________________
_________________________
21
_________________________
_________________________
46
_________________________
_________________________
22
_________________________
_________________________
47
_________________________
_________________________
23
_________________________
_________________________
48
_________________________
_________________________
24
_________________________
_________________________
49
_________________________
_________________________
50
51
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement