QUICK USER GUIDE
Firmware version 5.06
CA-6
Alarm Control Panel
QUICK USER GUIDE
The full version of User Manual and other manuals are
available on CD included in the control panel delivery set
or on the website www.satel.eu
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
[email protected]
www.satel.eu
ca6_us_en 06/12
We are glad that you have chosen a product offered by us. We wish you satisfaction
with your choice and would like to assure you that we are always ready to provide
expert assistance and information on our products.
Out of concern for the environment, SATEL has decided to reduce its paper
consumption. Instead of comprehensive manuals we offer you a short guide for
control panel users. It contains all the information necessary for daily operation of the
panel. The other manuals are available in electronic form at www.satel.eu
SATEL is a manufacturer of a wide range of dedicated devices for use in security
systems. Additional information on these products can be found on the website
www.satel.eu or at points of sale offering our products.
Hereby, SATEL sp. z o.o., declares that this control panel is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity may be consulted at www.satel.eu/ce
Read this manual carefully before operating your security system.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
IMPORTANT !
The alarm system is not able to prevent a burglary or robbery. Its purpose is to signal
an emergency. The system should be installed by qualified professionals who will
inform you about the rules of using it and ensure its regular maintenance and testing.
We recommend regular testing of the alarm system to ensure that it will react properly
in case of burglary or robbery.
SATEL's goal is to continually improve the quality of its products, which may result in
alterations of their technical specifications and firmware. Current information on the
introduced modifications is available on our website.
Please visit us at:
http://www.satel.eu
1. Keypads description
1.1
Indicator LEDs
Green
illuminated – 230 V AC mains and battery power OK
blinking – low battery
extinguished – 230 V AC power failure
Green
illuminated – control panel occupies telephone line
Red – letters A and B are used for partition identification
blinking – alarm
Yellow – letters A and B are used for partition identification
illuminated – partition armed
blinking – exit delay countdown
Yellow
blinking – trouble (to check the cause of trouble, press and hold down the 7 key)
1…8 Red – digits correspond to zone numbers
extinguished – normal zone status
blinking slowly – zone bypassed
illuminated – zone violated
blinking rapidly – alarm memory
illuminated, briefly extinguishing every 2 seconds – zone tampered
flashing every 2 seconds – tamper memory
Yellow [CA-6 KLED-S only] – illustrates the functioning of the buzzer in the keypad
When using the features available in the control panel, the LEDs can also provide additional
information.
1.2
Keys
The keys designated with digits and letters enable entering the code and data when using the
keypad.
The key allows you to:
− enter the user menu (after entering the code);
− enter the service mode (after entering the service code);
− exit some functions.
The # key allows you to:
− arm/disarm and clear alarm (after entering the code);
− enter the service mode (after entering the service code);
− confirm the entered data.
Note: The service mode is not available when there is an alarm or any partition is armed.
Press and hold down selected keys for about 3 seconds to:
5 - view the alarm log;
6 - view the trouble log;
7 - view the current troubles;
8 - enable/disable the CHIME signal in the keypad (signaling violation of selected zones
with 5 short beeps);
2
CA-6
SATEL
9 - change the keypad backlight mode [only in CA-6 KLED-S] – the number of short beeps
indicates which backlight mode is enabled (1 – no backlight; 2 – automatic backlight; 3 –
permanent backlight);
0 - trigger the auxiliary alarm;
- trigger the fire alarm;
# - trigger the panic alarm.
1.3
Sound signaling
Beeps generated during operation
1 short beep – pressing any number key.
3 short beeps – to signal:
− arming;
− disarming and/or alarm clearing;
− deactivating the 13. BI SWITCH type output by means of user functions.
4 short beeps and 1 long beep – to signal:
− entering the service function menu;
− activating the 12. MONO SWITCH or 13. BI SWITCH type output by means of user
functions;
− finishing the function and exiting the user menu, after confirming the entered data.
2 long beeps – an unknown code, unavailable function, or exiting the function without
confirmation of the data entered (after using key).
3 long beeps – refusal to arm (some zones are violated or battery failure).
Events signaled by sounds
1 short beep every 3 seconds – to signal:
− service mode;
− entry delay countdown.
2 short beeps every 3 seconds – trouble (the sound signaling of trouble will stop after
viewing the current troubles).
5 short beeps – zone violation (CHIME).
1 long beep every second – fire alarm.
1 long beep every 3 seconds – exit delay countdown.
5 long beeps – zone violation:
− the 4. DAY/NIGHT type, when the partition is disarmed;
− the counter type (triggers alarm after a preset number of violations), when the partition
is armed.
Continuous beep – alarm.
Notes:
• Only installer selected events are signaled.
• Alarms will be signaled as long as programmed by the installer.
2. Codes and users
To perform many of the CA-6 control panel functions you must enter a code. By default, the
following codes are preprogrammed in the control panel:
master (administrator) code for partition 1: 1234
service code: 12345
SATEL
CA-6
3
The master user (administrator) can add new users. For security reasons, each user should
have their individual code. The master user defines an authority level for each user. The
functions to which the user has access depend on the authority level. For description of the
authority levels please refer to the full user manual. The master user can create up to 12
users. The users can have access to one or both partitions.
The service code enables access to the service functions, but does not allow everyday
operation of the control panel (using this code you will not be able to arm or disarm the
system).
3. Arming
Prior to arming, make sure that there are no violated zones (e.g. open windows or doors),
which may prevent the system from arming (if the system has been so configured by the
installer).
After arming, the exit delay countdown may be running, which allows you to leave the
premises without triggering alarm (the zones will be armed only when the exit delay
countdown is finished).
If, during the exit delay countdown, the control panel will not register leaving the premises
(the zone monitoring the exit route will not be violated), the selected zones can be
automatically bypassed, thus enabling you to stay in the protected premises. The installer
shall define which zones are to be bypassed in such a case.
3.1
Full arming
Enter the code and confirm using # key. The partition(s) to which the user has access will be
armed.
Note: The user having the authority 7 can only activate partial armed mode (the installer
selected zones will be bypassed).
3.2
Quick arming
If your installer has enabled the Quick Arm feature, you will be able to arm the system without
using the code. To quickly arm the system, press in turn the keys:
0# - both partitions;
1# - partition A;
2# - partition B.
3.3
Arming in silent mode
During the silent armed mode, the alarms from zones are only signaled on the keypad
(however, the installer can program the control panel output so that it can provide information
about alarms being signaled on the keypad). After activating the silent armed mode, the
installer selected zones will be bypassed.
1. Enter the code and confirm using key. The
,
and
LEDs will start blinking.
2. Press the 5 key. The partition(s) to which the user has access will be armed in silent
mode.
4. Disarming and alarm clearing
In order to disarm the partition and clear the alarm, enter the code and confirm with the # key.
4
CA-6
SATEL
5. Triggering the alarm from keypad
If your installer has enabled this feature, the alarms can be triggered from the keypad as
follows:
fire alarm – press and hold down the key for approx. 3 seconds;
auxiliary alarm – press and hold down the 0 key for approx. 3 seconds;
panic alarm – press and hold down the # key for approx. 3 seconds.
6. Viewing alarm log
Press and hold down the 5 key for approx. 3 seconds. Information on the alarm is presented
on the numbered LEDs:
− a single LED is illuminated – alarm from the zone whose number corresponds to that of
the LED;
− a single LED is blinking – tamper alarm from the zone whose number corresponds to
that of the LED (double EOL zone wiring);
− seven out of the eight LEDs designated by numbers 1-8 are illuminated and one of the
LEDs designated by numbers 1-5 is blinking – alarm from keypad. Blinking of the LED
has the following meaning:
1 – fire alarm triggered from keypad;
2 – panic alarm triggered from keypad;
3 – auxiliary alarm triggered from keypad;
4 – keypad tamper;
5 – three invalid codes entered.
Information about the last alarm is displayed first. If you press any key (except for )
information about the previous alarm will be displayed. Press the keys repeatedly to scroll
back the alarm log.
7. Viewing trouble log
Press and hold down the 6 key for approx. 3 seconds. Information on troubles is presented
on the numbered LEDs. The LEDs indicate (status when lit):
1 – OUT1 trouble;
2 – OUT2 trouble;
3 – OUT3 trouble;
4 – 230 V AC loss;
5 – battery trouble;
6 – no keypad supply;
7 – time not set;
8 – monitoring trouble.
Information about the last trouble is displayed first. If you press any key (except for )
information about the previous trouble will be displayed. Press the keys repeatedly to scroll
back through the trouble log.
8. Viewing current troubles
Press and hold down the 7 key for approx. 3 seconds. The trouble information is presented
on LEDs designated by digits and on LEDs designated by letters. The LEDs indicate (status
when lit):
1 – OUT1 trouble;
SATEL
CA-6
5
2 – OUT2 trouble;
3 – OUT3 trouble;
4 – 230 V AC loss;
5 – battery trouble;
7 – time not set;
8 – monitoring trouble;
A
– no voltage on telephone line;
B – telephone line trouble – wrong dial tone;
A
– telephone line trouble – no dial tone;
B – control panel RAM memory error.
9. Using selected user functions
All the user functions are described in the full version of the user manual. Described below
are just a few selected functions.
9.1
Changing your own code
1. Enter the code and confirm using key. The
,
and
LEDs will start blinking.
2. Press the 1 key.
3. Enter the new code (4 to 6 characters) and confirm with # key.
9.2
Zone bypassing
1. Enter the code and confirm using key. The
,
and
LEDs will start blinking.
2. Press the 4 key
3. The LEDs designated by digits indicate the current zone status:
LED extinguished – the zone is not bypassed,
LED blinking – the zone is bypassed.
4. Using the keypad, enter the number of zone which is to be bypassed (if it is not bypassed)
or unbypassed (if it is bypassed).
5. Having selected the zones to be bypassed / unbypassed, press the # key.
Notes:
• For security considerations, the installer can reduce the number of zones that the user is
authorized to bypass.
• Bypassing the zones reduces the level of security. Prior to arming, make sure that there
are no accidentally bypassed zones, which can allow an intruder to gain access to the
protected area, despite the system being armed.
• If a zone is bypassed because of its malfunctioning (e.g. because of detector trouble), call
the service technician immediately to repair the fault.
6
CA-6
SATEL
10. Quick keypad operating instructions
illuminated – 230 V AC mains and battery power
OK
blinking – low battery
extinguished – 230 V AC power failure
illuminated – control panel occupies telephone line
blinking – alarm
illuminated – partition armed
blinking – exit delay countdown
Arming
Disarming
Alarm clearing
[CODE]#
Quick arming
0# - both partitions
1# - partition A
2# - partition B
Triggering the alarm from keypad
fire alarm
- press and hold down the key
for approx. 3 sec.
panic alarm
- press and hold down the # key for
approx. 3 sec.
auxiliary alarm - press and hold down the 0 key for
approx. 3 sec.
Entering the user menu
[CODE]
Viewing trouble log
press and hold down the 6 key for approx. 3 sec.
Starting the user functions
[CODE] 1 – Change own code
[CODE] 2 – Add user
[CODE] 3 – Erase user
[CODE] 4 – Bypass zones
[CODE] 5 – Arming silent
[CODE] 6 – Set time
[CODE] 7 – MONO outputs activate
[CODE] 8 – BI outputs switch
[CODE] 9 – Supply reset
[CODE] 0 – Telephone DOWNLOADING start
Viewing current troubles
press and hold down the 7 key for approx. 3 sec.
Enabling/disabling the CHIME signal
press and hold down the 8 key for approx. 3 sec.
blinking – trouble
the LED illustrates the functioning of the buzzer in
the keypad
Viewing alarm log
press and hold down the 5 key for approx. 3 sec.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement