iPR-3 proximity reader
User manual
Introduction
The proximity reader iPR-3 is intended to be applied in different access control systems, using RS232, Wiegand 26, Wiegand 37, Wiegand 42 or
TouchMemory interface.
The interface type is to be changed by special PC programm. If you need to change the interface type please call your distributor.
The reader is placed in a hermetic vandal-proof case made of polished stainless steel with LED indicator on the front cover.
Types of cards
Integrated Technical Vision ltd manufactures readers operating with amplitude modulation (ASK) proximity cards and tags.
Benefits
Case
Material
Dimensions
Weight
Ambient Conditions
Oper. temp.
Stor. temp.
Humidity
Electrical
Voltage
Current
Max current
Voltage ripple
1.5mm thick stainless steel
11
6 x 80 x 15 mm
150 g
-35 0 C ... +60 0 C;
-30 0 C … +80 0 C;
100% rel. at +25 0 C
+9. . . +16 VDC up to 50 mA up to 80 mA up to 500 mV p-p
.
Distance of reading
Typical reading distance is 35-40 mm and depends on tag type used with it. This parameter is valid for power supply voltage range from +13.5
VDC and ripple up to 150 mV p-p
.
http://www.itvsystems.com.ua
Integrated Technical Vision Ltd
1
Wiring
Reader has 8-wire cable for connecting to the access control panel.
Color
Green
White
Red
W2 / W3 / W4 / WS
Data 0
Data 1
+V
Black
Brown
Orange
Blue
Yellow
GND
Red Led
Green Led
B e e p
Hold/Synch
Table 1. The wires assignment.
RS232
Function
Rx
Tx
+V
GND
–
–
–
Hold/Synch
TouchMemory iButton
–
+V
GND
Red Led
Green Led
Beep
Hold/Synch
AWG22 multiwire signal cable is recommended. Using this cable the maximum length of 100 meters can be obtained*.
Type of interfaces
The proximity reader is intended to apply in different access control systems, using RS232, Wiegand 26, Wiegand 37, Wiegand 42 or Touch-
Memory interface.
Mounting
It is recommended to mount the reader on a wall closely to a door at appropriate height.
Do not place the reader on the metal surfaces, since it causes decreasing of reading distance.
If two readers are mounted at a distance less than 50sm, reading distance of a card may be reduced appreciably. In such a case, connect yellow wires of the readers. The readers will synchronize and work in turn.
Synchronization allows mounting of two readers at a small distance, to the extent of reading distance of a card. In case that, two readers are mounted at a distance less than reading distance of a card the card may be read by the reader behind the wall.
- Remove the cover from the reader.
- Drill 4 openings 35mm deep
- Prepare all wires for connection and connect them to the reader in accordance with Table 1 and User Manual of the access control panel to be utilized.
- Mount the reader to the wall using the fixturing provided.
- Secure cover to the reader. Ensure that all locking tabs are securely engaged.
2
* Not for RS232 interface
Integrated Technical Vision Ltd http://www.itvsystems.com.ua
The Reader Operation
The RFID Card Code Reading
The card code reading is annunciated by built-in buzzer and LED lamp according to interface type and annunciation mode (see Section «Data transfer and Annunciation»).
Repeated reading will be available after 0.8 sec if the card is removed from the reader sensing area.
Hold Mode
Reader is turned to the hold mode while yellow wire is closed to ground.
In this mode reader does not read cards, thus current consumption decreases.
Do not apply voltage to yellow wire!
Data transfer and control of annunciation
The reader is provided with two-colour LED indicators and buzzer. LED and buzzer function according to interface type programmed and annunciation mode.
00
01
02
03
04
05
06
07
Wiegand or TouchMemory Interface
Engaging of LED and buzzer is possible automatically or by grounding of corresponding wire according to the table 2.
Table 2. Annunciation mode:
Buzzer
Beep on card read
Red LED Green LED
LED normally on, switch off at reading Blinking at reading
Control from outside LED normally on, switch off at reading Blinking at reading
Beep on card read Switch off Blinking at reading
Control from outside Switch off Blinking at reading
Beep on card read LED normally on, switch off at reading Control from host
Control from outside LED normally on, switch off at reading Control from host
Beep on card read Control from host Control from host
Control from outside Control from host Control from host
Data transmissions from reader comply with standard Wiegand26, Wiegand37, Wiegand42 or TouchMemory protocols. Protocol for TouchMemory interface from family 01 (to satisfy the requirements DS1990).
Interface RS232
To control annunciation send control packet to the reader. Packets should be transmitted with 2 400 baud rate, 8 bit data, no parity, 1 stop bit.
http://www.itvsystems.com.ua
Integrated Technical Vision Ltd
3
Packet format:
Bit byte 0 byte 1
7
0
–
6
1
5
0
4
0
– red blinks –
3
1 red uninterruptedly
2
0
–
1
0
–
0
1
– byte 2 green stedy
– green blinks
– – buzzer pulsatory
– buzzer uninterruptedly
1 – corresponds LED or buzzer switched on. LED blinking and buzzer pulsatory control bits have highest priority.
Annunciation does not change until next control packet received.
Reader transmits data as follows: data: bit
Value
7 6 5 4 3 2 1
0 0 1 1 x x x
0 x
Checksum: exclusive OR of low nibbles of bytes from 1 to 10, high nibble of always must be 3h.
# of byte 0 1...10
11 12
Destination 23h data checksum 0Dh
Example: Card code 7E000460AA will be sent as:
23h, 37h, 3Eh, 30h, 30h, 30h, 34h, 36h, 30h, 3Ah, 3Ah, 3Bh, 0Dh.
Limited Warranty
Integrated Technical Vision Ltd. warrants that for a period of eighteen months from the date of purchase, the product shall be free of defect in materials and workmanship under normal use and that in fulfillment of any breach of such warranty, Integrated Technical Vision ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not damaged incurred in shipping or handing, or damaged due to causes beyond the control of Integrated Technical Vision Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Integrated
Technical Vision Ltd. This warranty contains the entire warranty. Integrated Technical Vision Ltd. neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any warranty or liability concerning this product.
In no event shall Integrated Technical Vision Ltd. be liable for any direct, indirect or consequential damages. Loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.
4
Integrated Technical Vision Ltd http://www.itvsystems.com.ua
