KEETEC bS 400, bS 400 LED PARKING SENSOR USER MANUAL

KEETEC bS 400, bS 400 LED PARKING SENSOR USER MANUAL
KEETEC bS 400, BS 400 LED
Parking sensor
10R-03*1223*00
Attention: Before installing, read the instructions and recommendations
contained in the manual. Equipment must be installed and used in accordance with these instructions. The device is designed for installation in motor vehicles
with 12-volt electrical. The device must be connected to 12V and negative terminals
grounded. The manufacturer and retailer are not responsible for any damages resulting from improper installation, use, operation or control of the product differently from the instructions for use. Incorrect repairs to the facility or its treatment are
at risk of damage to the equipment or vehicle power supply and loss guarantees.
For proper operation and flawless product, we recommend installation of professional service.
I. SYSTEM DESCRIPTION
BS 400, BS 400 LED Park assistent is designed for motor vehicles with a supply voltage of 12V
and serves as an aid for drivers to ease the parking of motor vehicles. The system is activated
when reverse gear is engaged or active, depending on vehicle speed. When in the parking
closer to the obstacle at a distance of 1.5 m (rear) or 1m (front), run the acoustic signal and the
display optical signal away from the obstacle. The closer the obstacle, the beep rate is increased
until eventually the tone is continuous. The system includes an anti-Hook, which ensures that parking sensor nevyhodnocuje towing or spare on the tailgate as a barrier.
brake
s D
or
ns C
se B
A
signal
of speed
display
control unit
user manual
Sound and visual signaling distance from the obstacle
Rear mount
Distance from
obstacles (m)
Zone
> 1.5
1.5 - 1.2
1.1 - 0.9
0.8
0.7 - 0.6
0.5 - 0.4
<= 0.3
safe
safe
safe
risk
risk
dangerous
dangerous
Alarm
without
bi ...... bi ......
bi ...... bi ......
bi ... bi ...
bi ... bi ...
bi ......
bi ......
control unit
D
C
D
buzzer
without
1 yellow
2 yellow
3 yellow
4 yellow
4 yellow 1 red
4 yellow 2 red
Zone
Alarm
Color display
(LED)
> 1.0
0.9 - 0.8
0.7
0.6
0.5
0.4
<= 0.3
safe
safe
safe
risk
risk
dangerous
dangerous
without
bi ...... bi ......
bi ...... bi ......
bi ... bi ...
bi ... bi ...
bi ......
bi ......
without
1 yellow
2 yellow
3 yellow
4 yellow
4 yellow 1 red
4 yellow 2 red
A
B
C
D
Display
yellow
white
Power
skelet
(+)back light
(ignition)
red
sensors
Rear mount
side view
90
B
D
A
Measure the distance between
sensors A and D will get the
distance ”L“.
Drill holes for sensors
Note: If the parking sensor is mounted to the front of the car and the red wire is not connected
to the reversing light.
70
If you want to secure the best possible detection sensors A and D, place the 8-13 cm from
the edge of the vehicle. We recommend 11 cm.
Choose a suitable location and
acreage for drilling holes for sensors
A and D.
Distance ”L“ Divide into 3 equal parts. Sensors
B and C, place the end of the first and second
parts so that the distance between the sensor all
the same.
Drill bit on the sensor.
Installing sensors
side view
0
100(cm)
70
100(cm)
View distance display BS 400 LED
Safe distance 110 - 150cm
Safe distance 70 - 100cm
Bi……Bi……
Installation procedure
1. Find a suitable place for installation of sensors
2. Measured points for the installation of sensors A and D
3. Measured points for the installation of sensors B and C
4. Drill holes for sensors
5. Install the sensor into the prepared hole and draw wires
6. Fix screen and mount control unit
7. Connect all power cables and connectors according to wiring diagram
Position sensors
Make sure that the lateral angle of 90 ° is an obstacle that could cause a false alarm or affect
the operation of sensors.
Installing the display and control unit
Mount the screen on the
dashboard or rear window. The place where it is
located display would be
well viditelné
Control unit is positioned so as not to face
the effects of high temperature, moisture and
mechanical damage. In the case. That parking sensors are mounted to the front bumper,
the control unit is placed under the dashboard.
Bi…Bi…
Dangerous distance 0-30cm
Dangerous distance 0-30cm
Bi……
Dangerous distance 0-30cm
Dangerous distance 0-30cm
90
90
90
Hardly detectable obstacles
Place the sensor so that no interference with the vehicle in the shooting.
Direction of sensor
smooth and sloped
Bi……
View distance display BS 400 LED
Pull the wires from the
sensors inside the vehicle.
Place them so that future
damage.
Place the sensor into
the drilled holes.
Risk distance 40 - 100cm
Risk distance 40 - 60cm
uP
uP
smooth and round surface
Checking the functionality of the system
location and angle of
sensors
yellow LED diods
red LED diods
DIP
switch
Nr. 2
DIP
switch
Nr. 3
A
The measured points for the sensors
make small holes.
150(cm)
Front mount
0
Sensors and install on
a clean surface with no
vertical metal elements.
speed of signal (pulse)
brake (+)
black
Range of the device, display and alarm
top view
The opening height from
the ground should be in the
range from 0.5 m to 0.8 m.
We recommend 0.55 m.
D
A
setting the sensitivity
of sensors
II. FUNCTIONS
150(cm)
D
SENSOR ASSEMBLY
WIRING of BS 400, BS 400 LED
Low High
rear bumper
0.3 - 1.5m
ON
front bumper
0.3 - 1.0m
DIP
OFF
Sound signaling on the LED display
sound signal from the 1.5 m
yellow LED shine
ON
sound signal from the 0.5 m
DIP
OFF
OFF
ON
ON
red LED shine
Funkcia Anti-hook
ystem signals the real distance from the obstacle
switched system signals shifted by 20 cm distance
from the actual distance from the obstacle
The back side of the display
ns
se
A
90
C
Drill holes for the
sensors should be at
the same level.
The sensors are mounted on the rear or front bumper at a height of 0.5 meters to 0.8 meters
from the ground. Location at the end of the bumper is not recommended (risk of damage during
a collision). Before installation, clean and prepare the bumper, where the sensors are located.
Place the screen on the dashboard, rear view mirror or in the interior of the vehicle. The control
unit should be located inside the vehicle, not to exposure to high temperatures and humidity.
Warning: Do not mount the control unit to the metal of the vehicle!
or
s
B
A
display
0
B
Position of sensors
DIP
OFF
Note: If the DIP is set to ON, the red wire is used to turn on and off systému.Pokud is set to OFF,
DIP, red wire connects to the ignition is activated and saturated in two ways:
1. Vehicle-speed (must be connected to the yellow wire) - the system is activated to set rychlosti.
After crossed the system automatically shuts down. After a fall below the set speed the system is
active again.
2. pressing the brake pedal (must be connected to the white wire) - After pushing the foot brake
system works 15 sec. If the barrier will reach even after 15 seconds, the system is automatically
activated.
0.3-0.4m
0.6-0.8m
A
Distance from
obstacles (m)
DIP
switch
Nr. 1
1 2 3
Front mount
C
B
0
ON
Color display
(LED)
IIi. MOUNTING SYSTEM
bzučiak
back light
top view
Settings DIP switches:
The recommended distance and position sensors:
0.5-0.8m
sK
1.5m
1.0m
objects absorbing
ultrasonic waves
buzzer
programming
button
cabel
Function of programming button
When programming the system must be turned on and not to indicate any obstacles.
1. Turn on / off the alarm on the display - press the 1 button to turn off the alarm. To turn on press
1 button again.
2.Setting the display on the LED display by the location of the display - press the button for 6 seconds until the yellow arrow
is not tip over in the opposite direction
. The setting is used
to display the location the ceiling of the vehicle that signaled the real obstacles to the party.
3.Adjust the speed in which the system will be activated - press the button for 9 seconds until the
display displayed
. Release the button. The arrows start to flash. The system is in programming mode. Achieve the desired speed of vehicle in which you want the system to function and
press the button. Speed is set. Activation of the system according to the speed of the vehicle is
used when mounting sensor into the front bumper.
4. Reset the system - if you want to set the system to its original settings, press the button for 12
seconds . The display
and all the yellow and red LED lights up. Release the button. The
entire display will blink. Press 1. The system is set to the original settings.
Description of the installation and test the system:
1. Set sensor according to the instructions for use. Once installed, adjust the wiring to prevent
damage.
2. Power control unit to light under backing diagram.
3. Connect the wires from the LED display to the control unit. Sensors just yet.
4. Turn the ignition on and shift into reverse. The LED display shows the default settings and the
system is in test mode.
Test: : A: If the LED display lights up, check its connections to the control unit and check the
power management unit, if not below 9V.
B: If the display is not right or some LED lights and buzzer sounds continuously, disconnect
power from the control unit and connect it again. If the problem persists, you may be wrong
and the control unit is needed to replace the system.
5. Plug one sensor into the connector on the control unit. Check functionality. If everything is in
order, disconnect the sensor and check the functionality of all sensors. After checking all the
sensors connect to the control unit.
Test: A: When connecting the sensor to the controller will continuously sound the buzzer and
some LED lights, check for any nearby sensors or obstacles are not close to large sources of
interference (eg power cables).
B: If the display shows the distance from any obstacles and reach the sensor is not any
obstacle, the sensor can scan the ground or any part of the vehicle (eg, license plate, tow bar).
Check the location of the sensors.
C: If the system still does not work after checking the above, it may be bad sensor or the input
of the control unit. Upon such finding is necessary to replace the wrong part of the system.
Note:
1. vehicle must be started during installation of ultrasonic sensors.
2.range sensors can be affected by the following circumstances: heavy rain, gravel, bumpy,
downward path, very cold weather, high heat and humidity or sensor located above the ice
surface.
3.when the sensors are located in the vicinity of a switch, electric waves, alternating or
unidirectional tension, these factors can affect the effectiveness of sensors.
4. sensor should be correctly fitted.
5.sensors will be more effective if they are not installed on the metal of the bumper.
6.Before using check the correct functionality of the system.
7.system serves only as a supplement for parking and therefore the seller is not responsible for
damage caused by the parking system installed.
Technical parameters
Supply voltage
Operating temperature
Display size
Operating current
Frequency Ultrasonic sensors
BS 400, BS 400 LED
9V - 16V
-30°C - +70°C
148x20x17 mm
20 - 200mA
40 KHz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement