USER'S MANUAL - Oz Security Systems

USER'S MANUAL - Oz Security Systems
 VERSION:E1201
DIGITAL SECURITY SYSTEM
USER’S MANUAL oë
LA A
e =
©
Cd i
E
Applied to Box Cameras, IR Waterproof Cameras, Dome cameras
Thank you for purchasing our products. Please read the manual carefully before operating
Safety Precaution
A Dont dismantle without authority.
becareful thunder striking
Note: Ta avoid thunder-strking, please dont open the backcover,
fie maintenance must be made by our authorized serviceman.
This symbol means that there might exist uninsulated dangerous voltage inside the case,
be careful of electric shock.
This symbol reminds you to pay attention to important operation and maintenance
instructions in the accompanied information.
=f =
Warning
Power Supply Interface:If it is 12V/24V, the charger don't have polar nature; if itis 12V
only, please connect the cable according to anode and cathode on the board
* In order to prevent damage caused by fire or electric shock, please do not put cameras
exposed in the moist environment or rainwater.
* Please make sure the adapter is consistent with product specifications, otherwise it might
cause fire, electric shock or damage.
= Pay attention to polarity of the adapter, it might cause some accidents like fires.
* Please don't connect multiple cameras with the same adapter at the same time; overloading
of adapter capacity may cause fires.
* Power supply must be firmly fixed so as not to loose to cause fires.
+ If the device gets abnormal smell or sMENTEREe”, please stop it immediately and contact
with our customer service center.
* If the camera doesn't work as usual, please do not dismantle it by yourself. Please contact
our Jocal distributor or our maintenance office authorized by our company, otherwise we won't
promise warranty.
* Please do not splash water on the product components when cleaning.
Notes
Interface Function Description
1. Do not make the products under great impact or stay away from strong electromagnetic
interference and vibration.
2. There are some sophisticated parts inside the camera, therefore, during transportation
and installation, please avoid the damage cause by stress or severe vibration. For the sake of 7
safety, please do not switch on power before accomplishing all installation.
3. Please comply with all electrical safety standards during operation, camera or signal
transmission cable should maintain a sufficient distance (50 meters) with high-voltage
equipment or cables, ifnecessary, lighting and thunder protective measures must be taken.
4, Please install the camera in well-ventilated environment.
5. Please do not make the camera face sunshine or other strong light directly in case of any
damage to the lens and the sensor.
6. The temperature and humidity range for cameras work are -10 ~ 50 °C, less than 95% ENTER
separately, please do not start cameras beyond this range.
7. To avoid lightning strikes, please make sure the installation of power supply ground line in
a good condition. LEFT/RIGHT -
8. To prevent the equipment from damage by shower or splash of water, please do not place Exit the next menu and modify the parameter.
the device substances such as liquid.
230 AV CAMERA
Connector Description
`
VIDEO OUTPUT 12VDC POWER INPOUT
Enter or Exit the menu, Press ENTER into Main Menu.
UP/DOWN UP and DOWN for move up and down
LEFT, RIGHT for modifying the menu parameters'press RIGHT to
The using and brief introduction of the OSD (pull-ENTER menu)
-3- 4-
The basic set up of the OSD
Press the “MENU” key on the menu, the following main control profile with iconic shot
will appear on the screen (As the following picture).
SETUP MENU
Dee
di у AUTOS
Le) PUSH
id
PICT ADJUST 4
ATR
MOTION DET — ON
NEXT
EXIT# SAVE ALLd
OSupport eight foreign languages. The user can see the setup items clearly.
©When click the menu frame, the set up parameters willappear. The user can adjust the
parameters or the check the previous settings easily.
©The users can use the menu control key on the camera tail to choose and set up the
parameters, to reach the best condition in differentEnvironments.
The introduction of the OSD main function
@Lens settings
| The first item of the OSD profile |
SETUP MENU
{RITE
| SHUTTER/AGC
elas ADJUST
| MOTION LT
NEXT
EXIT: SAVE ALL
AN
Press the left/right Choose DC and
key to choose the press the Enter key
4 manual or auto iris. J for the submenus. 7
Notes: In the out of factory settings, it should choosethe manual if install the fixed iris lens, and
it should choose the DC when you use the Auto iris lens. И 15 Auto setup for the DC iris mode.
And the speed is 080.
O The AGC Setup
| The second item of the main menu |
LENS :
SHUTTER/AGC
WHITE BAL
BACKLIGHT
PICT ADJUST
ATR
MOTION DET
TA
EXIT SAVE ALL
Press the left/right
key to choose the
manual or auto set
UE
A SETUP MENU \
J
MEUTO SETUP %
HIGH LUMINANCE
MODE SHUT+DC IRIS
ET ne
LOW LUMINANCE
MODE AGC
BRIGHTNESS 10.50
RETURNJ
Choose the Auto Setup
and press the Confirm
key to enter into the
\submenus(AGC control)
SETUP MENU i \
LENS
SHUTTER/ AGC
WHITE BAL
BACKLIGHT
PICT ADJUST
MANUAL SETUP
MODE
ATR
MOTION DET
=
NEXT
EXITa SAVE ALLS
Press the left/right Choose manual and
key to choose the press the confirm key to
manual or auto set enter into the submenus
(Up т \(AGC control) +
Note:in the out of factory settings, this is selected auto mode. If it is fixed IRIS lens, then
in the submenu, the high-grey mode is shutter, brightness 024; low-grey mode is AGC,
brightness x 0.50; if thelens is auto IRIS, the in the submenu, the high-grey mode is shutter +
DC IRIS, brightness 024; Low-grey mode is AGC, brightness x 0.50.
@ White balance setting up
| The third item of the main menu |
Color OSD
@ White balance setting
| The fifth item of the main menu |
SETUP MENU
J
SHUTTER/AGC
PICT ADJUST
ATR
MOTION DET
NEXT:
EXIT SAVE ALLM
Press the right and left key to set up BLC
- 11 -
Г | N
SETUP MENU PICT 4 Tee
PICY ADJUST
LENS :
| SHUTTER/AGC | MIRROR
‹ BAL С | BRIGHTNESS
ATR
| MOTION DET
NEXT ,
7307 SAVE Та НУВ
Press the conform key to
the submenu
Press the conform key to
A
Note: the compensatory model is BLC and high-light compensatory. In the out of factory
setting, this setis close.
@ATR Setting
| The sixth item of the main menu |
-12-
PRIVACY
AREA SEL
| TOP
CAMERA RESET
Wi ДЕЯ E
SYNC INT |
LANGUAGE
|CAMERA RESET
1
EXIT SAVE ALL«
The second page of the
Tn
EXITd SAVE ALL
Choose “open” and press
main menu (Color to ee the “left” or “right” the confirm button to
\_ B/W mode adjust) ) (Key to switch this function » enter sub-menu
@Privacy settings
| Main menu first item on the second page |
Note: in the out of factory settings, this is off. The user can choose to open this feature,
four hidden areas can be set up.
-15- - 16 -
@Day / Night mode setting @2D noise reduction settings
| The second item on the second page of the main menu | { The third item on the second page of the main menu |
OFF
DAY/NIGHT LT
a
НЕ
CAMERA 10 ОМА
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
SEN) BACK
Press the “left” or “right” Р : 3300 SAVE ALL |
ï ress the confirm button
to choose Day / Night to enter sub-menu (AGC Press left or right keys Choose ON and press
mode; (Color switchover a the confirm button to
\_ and white/black adjust) |) J \ select ON or OFF J \ enter sub-menu
Note: In factory settings, this item is chosen off. The submenu noise reduction mode is Y /
C; Y grade selected 004; C grade selected 004; 2D noise reduction using a low-light scene
in order to improvethe S 7 N to improve illumination.
fr - -18-
Note: in the factory settings, this is automatically. Submenu pulse is off; delay control 001;
day — night is 002; night — day is 003.
@Camera identification code settings
| The fourth item on the second page of the main menu |
AN SETUP MENU
PRIVACY
DAY/NIGHT
NR
CAMERA ID
SYNC
LANGUAGE
CAMERA RESET
BACK#
EXIT#
Press left or right keys
to select on or off
Note: in the out of factory settings, this is set as off.
>
J
"=
- 19 -
@Synchronization settings
| The fifth item on the second page of the main menu |
MSETUP MENU в
CAMERA ID
DAY/NIGHT
CAMERA Le
CAMERA ID
denied Fe
ABCDEFGHI JKLMNOPQRSTUY [EI
WXYZ0123456789- ! "ESTA" CAMERA RESET
(PRE a CS DAME AT
CHR1 CHR2
++++ CLR POS
CRIER] ETNA
Choose ON and press Press the left and right keys
the confirm button to of the keyboard to choose
- the synchronization mode
_ enter sub-menu J А y or,
Note: in the out of factory settings, the item is set as Synchronization
- 20 -
@Language settings
| The sixth item on the Second page of the main menu
CAMERA ID
CAMERA RESET
LIM
28
\ black adjust)
Note: out of factory settings, the P system is set as the Chinese; N system is set as English.
Me SETUP MENU \
PRIVACY
DAY/NIGHT
NR
Press the left or right keys of the
keyboard to choose the language
mode (Color switchover and white/
SAVE ÁLLe
-21-
@Camera reset settings
| The seventh item on the Second page of the main
Note: press the Resetbutton to
restore the factory settings of
the selected models.
OReturn to exit and save the settings
| Options on The bottom of main menu |
Note: After the camera parameters are set, you
can press the “SAVE ALL” to save the parameters
you set before the next booting up.
- 22 -
Press the “SAVE ALL" to reset
Na]
5E MENU
Press the “SAVE ALL” to reset
Ne —
SETUP MENU
PRIVACY OFF
DAY /NIGHT AUTOS
Г.
CAMERA 10 OM
E INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXITé
TURP
PRIVACY OFF
DAY /NIGHT AUTOS
ня La
CAMERA ID ON
SYNC I
NT
LANGUAGE ENGL ISH
CAMERA RESET
BACK JA
EXIT: ELA RE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement