DNA1991M - Dante Security
DNA1991M
IP IR PTZ Domes
Operations User Manual
Model Number: DNA1991YM
Description:
IP MP IR PTZ Domes
20X, 30x Optical Zoom
With Intelligent Analytics
Table of Contents
1
IR INTELLIGENT SPEED DOME INSTALLATION ............................................. 1
1.1
Installation Preparation ......................................................................................................................... 1
1.2
Initial Setup ............................................................................................................................................. 2
1.3
Dial Switch Setup (Analog Speed Dome) .......................................................................................... 2
1.3.1
Dial Switch Description .................................................................................................................... 2
1.3.2
Parity Setup ....................................................................................................................................... 3
1.3.3
Baud Rate Setup ............................................................................................................................... 3
1.3.4
Speed Dome Address Setup........................................................................................................... 3
1.4
Dial Switch Setup (HDCVI Speed Dome) .......................................................................................... 3
1.4.1
Dial Switch Description .................................................................................................................... 3
1.4.2
HD/SD Video Format Setup ............................................................................................................ 4
1.4.3
Baud Rate Setup ............................................................................................................................... 4
1.4.4
Speed Dome Address Setup........................................................................................................... 4
1.5
Reset and SD Card Installation (Network Speed Dome) ................................................................ 5
1.6
Speed Dome Installation ...................................................................................................................... 5
1.6.1
Overview ............................................................................................................................................ 6
1.6.2
Installation Conditions ...................................................................................................................... 6
1.6.3
Dig Installation Holes ........................................................................................................................ 6
1.6.4
Speed Dome Installation .................................................................................................................. 6
2
HANG MOUNT INSTALLATION ......................................................................... 8
2.1
Installation Components ....................................................................................................................... 8
2.2
Installation............................................................................................................................................... 8
2.2.1
Installation Requirements ................................................................................................................ 8
2.2.2
Installation Steps ............................................................................................................................... 8
i
3
CORNER MOUNT BRACKET .......................................................................... 12
3.1
Component Installation ....................................................................................................................... 12
3.2
Installation............................................................................................................................................. 12
3.2.1
Installation Requirements .............................................................................................................. 12
3.2.2
Installation Steps ............................................................................................................................. 12
4
POLE MOUNT BRACKET ................................................................................ 14
4.1
Installation............................................................................................................................................. 14
4.1.1
Installation Requirements .............................................................................................................. 14
4.1.2
Installation Steps ............................................................................................................................. 14
5
BRACKET DIMENSIONS ................................................................................. 16
5.1
Wall Mount Bracket ............................................................................................................................. 16
5.2
Hanging Mount Bracket (Multiple Lengths) ..................................................................................... 16
5.3
Corner Mount Bracket ......................................................................................................................... 17
5.4
Pole mount bracket ............................................................................................................................. 17
6
APPENDIX Ⅰ LIGHTNING PROOF AND SURGE PROTECTION ................... 18
7
APPENDIX Ⅱ ABOUT RS485 BUS ................................................................... 19
7.1
RS485 Bus Main Feature ................................................................................................................... 19
7.2
RS485 Bus Transmission Distance .................................................................................................. 19
7.3
The Problem in Practical Use ............................................................................................................ 19
ii
7.4
8
RS485 Bus FAQ .................................................................................................................................. 20
APPENDIX Ⅲ SAFETY ROPE INSTALLATION ............................................... 21
iii
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!
iv
Important Safeguards and Warnings
Safety Measures
1. Qualified Engineer Needed
The installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
The installation engineer or maintenance engineer shall have qualification certificate for work
at height.
The installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
Please read the installation manual carefully and keep it well for future reference,
We are not liable for any problems caused by unauthorized modifications or attempted repair.
2. Lifting Appliance Requirement
Please select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
The lifting appliances shall have the enough capacity to reach the installation height.
The lifting appliances shall have safe performance.
The precaution measures include two types: Warning and Note.
Warning: It is to alert you there is an optional risk of death or series injury!
Note: It is to alert you, there is an optional risk of damage or property loss!
Warning
1.
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
rated voltage conformed to Limited Power Source according to the IEC60950-1. (Power
supply requirement is subject to the device label).
2.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
3.
4.
Be sure to use all the accessories (such as power adapter) recommended by manufacturer.
Do not connect several speed domes to one power adapter. It may result in overheat or fire
if it exceeds the rated load.
5.
Before you connect the cable, install or uninstall, or begin the daily maintenance work,
please turn off the power and unplug the power cable.
v
6.
7.
Please make sure the produce is secure firmly on the wall or the ceiling.
Please turn off the power and unplug the power cable, If there is any smoke, disgusting
smell, or noise. Please contact your local retailer or customer service center for help.
8.
All the examination and repair work should be done by the qualified service engineers. We
are not liable for any problems caused by unauthorized modifications or attempted repair.
Note
1. Safety Transportation
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
This series product must use split type package during the transportation.
We are not liable for any damage or problem resulting from the integrated package during
the transportation.
2. When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
3. Do not try to dismantle or modify the device
There is risk of personal injury or device damage resulting from opening the shell.
Please contact your local retailer if there is internal setup or maintenance requirement.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
4. Do not allow other object falling into the device
Please make sure there is no metal or inflammable, explosive substance in the speed dome.
The above mentioned objects in the device may result in fire, short-circuit or damage.
Please shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.
Please pay attention to the camera. Avoid the sea water or rain to erode the camera.
5. Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
6. Installation Environment Requirement
This series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
This series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
7. Daily Maintenance
vi
Please use the soft cloth to clean dust on the shell, or user may use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.
Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
Do not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.
vii
1 IR INTELLIGENT SPEED DOME INSTALLATION
1.1 Installation Preparation
Basic Requirement
All installation and operation here should conform to your local electrical safety codes.
Before installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain the 8X weight of the speed dome.
About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
75 ohm.
Full cable with copper conductor
95% knitted copper shield
International Model
SYV-75-3
Max Transmission Distance
(M\Ft)
720P(25fps\30fps):500M/1640Ft
720P(50fps\60fps):300M/984Ft
1080P(25fps\30fps): 300M/984Ft
Note:
The above can be applied to analog speed dome and network speed dome
International Model
SYV-75-3
Note:
International Model
Max Transmission Distance
(M\Ft)
720P(25fps\30fps):500M/1640Ft
720P(50fps\60fps):300M/984Ft
1080P(25fps\30fps): 300M/984Ft
Max Transmission Distance
The above can be applied to HDCVI speed dome.
Set dial switch button
Set dial switch button according to control protocol and speed dome address. (Please refer to
user’s manual for detailed information.)
Please keep all package material well for future use
1
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.
Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are includes.
1.2 Initial Setup
The default setup is:
Address: 1
Baud rate: 9600
Parity: None.
1.3 Dial Switch Setup (Analog Speed Dome)
1.3.1 Dial Switch Description
There are two dial switch buttons on the PCB of one side of the speed dome (There are labels.).
User may use them to set speed dome baud rate, address and etc. See Figure 1-1 . It is 1 when
you set the button as ON.
For the protocol dial switch, user may refer to the following sheet. 1 is the lowest bit and the 8 is
the highest bit. 1~3 is NC neutral bit, 4 is the setting bit for 120Ω matched resistance, ON is to
connect 120Ω matched resistance, 5, 6 are the setting bit for parity, 7, 8 are the setting bit for
baud rate. Only when you cut off the power or restart the system after dial switch setup, can the
setup be valid.
Note:
The IR speed dome can automatically recognize the PELCO-D. PELCO-P and industry
standard protocol, control protocol doesn’t need to be set via dial.
Figure 1-1
2
1.3.2 Parity Setup
Please refer to the parity setup sheet for detailed information.
Address
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1.3.3 Baud Rate Setup
Please refer to the baud rate sheet for detailed information.
Address
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1.3.4 Speed Dome Address Setup
The speed dome uses dial switch to set address number, the encode mode adopts binary system.
1 to 8 is valid bit. The highest address bit is 255. User may refer to the following sheet for more
information.
1
1
1
2
3
4
5
6
7
8
……
254
255
2
3
4
5
6
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
…………………………………………………………………
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
7
8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
1.4 Dial Switch Setup (HDCVI Speed Dome)
1.4.1 Dial Switch Description
There are two dial switch buttons on the PCB of one side of the speed dome (There are labels.).
User may use them to set speed dome baud rate, address and etc. See Figure 1-2. It is 1 when
you set the switch as ON.
For the protocol dial switch, user may refer to the following sheet. 1 is the lowest bit and the 8 is
the highest bit. 1~3 is NC neutral bit, 4 is the setting bit for 120Ω matched resistance, ON is to
3
connect 120Ω matched resistance, 5, 6 are the setting bit for HD/SD video format, 7, 8 are the
setting bit for baud rate. Only when you cut off the power or restart the system after dial switch
setup, can the setup be valid.
Note:
The IR speed dome can automatically recognize the PELCO-D. PELCO-P and industry
standard protocol, control protocol doesn’t need to be set via dial.
Figure 1-2
1.4.2 HD/SD Video Format Setup
Please refer to the following sheet for more details about HD/SD video format.
7
8
Baud rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
1.4.3 Baud Rate Setup
Please refer to the following sheet for more details about baud rate.
8
Baud rate
OFF
OFF
9600bps
ON
OFF
4800bps
OFF
ON
2400bps
ON
ON
1200bps
5
6
HD/SD Video Format
1.4.4 Speed Dome Address Setup
The speed dome uses dial switch to set address number, the encode mode adopts binary system.
1 to 8 is valid bit. The highest address bit is 255. User may refer to the following sheet for more
information.
7
8
Baud rate
OFF
OFF
9600bps
ON
OFF
4800bps
4
2
3
4
5
6
7
8
……
254
255
1
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
…………………………………………………………………
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
1.5 Reset and SD Card Installation (Network Speed Dome)
User may see there are a RESET button, dial switch button and Micro-SD card slot on one side of
the PCB of the speed dome. See Figure 1-3. It is 1 when you set the button as ON.RESET
button is to restore factory default setup. Micro-SD card is to save the data.
User may refer to the sheet for dial switch information.
2
3
4
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Figure 1-3
Note:
For some speed domes there is only reset button and dial switch, or no any other buttons on the
PCB board (without tag) of the lateral ear; for some speed domes, the SD card is installed on the
module, please refer to the actual device for more details.
1.6 Speed Dome Installation
Note:
5
This chapter of installation includes IR intelligent speed dome and network IR intelligent speed
dome.
1.6.1 Overview
The speed dome has various brackets suitable for different environments. For detailed
information, please refer to chapter 2 and chapter 4. Here we are going to install the IR speed
dome with the analog wall mount bracket.
1.6.2 Installation Conditions
Wall mount bracket is for the indoor and outdoor hard wall construction environments.
Before the installation, please make sure the wall thickness can sustain the expansion bolt. The
wall can support at least the 8X of the speed dome weight.
1.6.3 Dig Installation Holes
Draw the installation holes in the wall according to the holes at the bottom of the wall mount
bracket. Dig the installation holes. Insert the expansion bolts into the holes. (Please note the
expansion bolts are not included in the accessories bag.). See Figure 1-4.
Installation Holes
Figure 1-4
1.6.4
Speed Dome Installation
Step1: Connect the speed dome to the bracket.
Use the quick installation screw of the speed dome and the quick instillation block to fix the
speed dome on the bracket. Use the M6 inner hex screw to secure firmly. See Figure 1-5.
6
Bracket
Cable
M6 Inner Hex Screw
Speed
Dome
Quick Installation Port
Quick Installation Screw
Figure 1-5
Step 2: Cable connection
Connect the video, RS485, power (Network, alarm, audio and optical fiber are optional) to the
corresponding ports. Please note the cable description here is for reference only.
Step3: Secure the bracket
Secure the speed dome and the bracket to the wall firmly. See Figure 1-6.
Figure 1-6
7
2 HANG MOUNT INSTALLATION
2.1 Installation Components
Please refer to the following sheet for bracket and components information. See Figure 2-1.
Straight Pole
Hang Mount Bracket Connection Plate
(With Cable Exit Slot )
Safety Rope Hole
Adapter Block
Screw thread Connection
Hang Mount Bracket Connection Plate
(Without Cable Exit Slot 2
Figure 2-1
2.2 Installation
2.2.1 Installation Requirements
The hang mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 8x weight of the speed dome.
2.2.2 Installation Steps
For the speed dome without the straight pole, please refer to the contents below.
Step 1: Dig Holes
Draw the installation holes in the wall according to the holes at the bottom of the connection plate.
Dig the installation holes. Insert the expansion bolts into the holes. (Please note the expansion
bolts are not included in the accessories bag.). See Figure 2-2.
Installation Holes
Figure 2-2
Step 2: Installation bracket components.
8
Fix the connection plate to the ceiling and then turn the connection block to the bracket
connection plate. See Figure 2-3.
Hang Mount Bracket
Connection Plate
Adapter Block
Figure 2-3
Step 3: Connect cable and the speed dome.
Connect the safety rope of the speed dome to the safety rope hole of the adapter block. Now you
can connect the cable: video, RS485, power (network, alarm, audio are optional). Please note
the cables listed here is for reference only.
Use the quick installation screw of the speed dome and the quick instillation port of the adapter
block to fix the speed dome on the adapter block. Use the M6 inner hex screw to secure firmly.
See Figure 2-4.
Safety Rope
Quick Installation Port
Quick Installation Screw
Figure 2-4
Please note, if the speed dome is installed in the outdoor environments, you need to paste
the silica gel on the surface of the flange and the surface and the cable exit.
For the speed dome with the straight pole, please refer to the contents below.
Step 1: Dig holes
9
Draw the installation holes in the wall according to the holes at the bottom of the connection plate.
Dig the installation holes. Insert the expansion bolts into the holes. (Please note the expansion
bolts are not included in the accessories bag.). See Figure 2-2.
Step 2: Components installation
Fix the bracket connection plate to the ceiling and then turn the straight pole to the connection
plate. Turn the adapter block into the straight pole of the bracket. See Figure 2-5.
Figure 2-5
Step 3: Connect cable and the speed dome.
Connect the safety rope of the speed dome to the safety rope hole of the adapter block. Now you
can connect the cable: video, RS485, power (network, alarm, audio are optional). Please note
the cables listed here is for reference only.
Use the quick installation screws of the speed dome and the quick installation port of the adapter
block to fix the speed dome on the adapter block. Finally, user may use the M6 inner hex screws
to secure the speed dome firmly. See Figure 2-6.
Safety Rope
Quick Installation Port
Quick Installation Screw
10
Figure 2-6
Please note, if the speed dome is installed in the outdoor environments, you need to paste
enough Teflon tape at the top screw thread of the steeve and then turn the steeve to the
flange firmly. Please paste the silica gel on the steeve connection surface to do the
waterproof work.
11
3 CORNER MOUNT BRACKET
3.1 Component Installation
Corner mount bracket and its components are shown as below. See Figure 3-1.
Figure 3-1
3.2 Installation
3.2.1 Installation Requirements
The corner mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments where there is a 90 degrees angle. Before the installation, please make
sure:
The wall is thick enough to install the expansion bolt.
The wall can at least sustain the 8x weight of the speed dome.
3.2.2 Installation Steps
Step1: Install corner mount bracket.
Please draw four holes position in the wall according to the holes of the corner installation
accessories. See Figure 3-2.
Installation holes
Figure 3-2
Step 2: Speed dome installation
For detailed information, Please refer to chapter 1.6.
After the installation, it is shown as in Figure 3-3.
12
Figure 3-3
13
4 POLE MOUNT BRACKET
Pole mount bracket and its components are shown as below. See Figure 4-1.
Figure 4-1
4.1 Installation
4.1.1 Installation Requirements
The corner mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments.
Before the installation, please make sure:
The pole bracket can sustain the 8X weight of the speed dome.
The diameter of the pole structure shall comply with the installation dimension of the clamp.
4.1.2 Installation Steps
Step 1: Fix bracket and the pole.
Install clamp and then pole mount bracket. Pull the cable out of the pole accessories and then
use clamp to fix the pole accessories to the pole. See Figure 4-2.
Finally, user may use glass cement to the output hole to secure waterproof.
Clamp and pole bracket connection
Pole bracket and the pole connection
Figure 4-2
Step 2: Install speed dome.
For detailed information, Please refer to chapter 1.6.
After the installation, the interface is shown as in Figure 4-3.
14
Figure 4-3
15
5 BRACKET DIMENSIONS
5.1 Wall Mount Bracket
The wall mount bracket dimensions are shown as below. See Figure 5-1.
Figure 5-1
5.2 Hanging Mount Bracket (Multiple Lengths)
The hanging mount bracket is shown as below. See Figure 5-2.
16
Figure 5-2
5.3 Corner Mount Bracket
The corner mount bracket is shown as below. See Figure 5-3.
Figure 5-3
5.4 Pole mount bracket
The corner mount bracket is shown as below. See Figure 5-4.
Figure 5-4
17
6 APPENDIX Ⅰ
THUNDER PROOF AND SURGE
PROTECTION
This series speed dome adopts TVS lighting protection technology. It can effectively prevent
damages from various pulse signals below 6000V, such as sudden lighting and surge. While
maintaining your local electrical safety code, you still need to take necessary precaution
measures when installing the speed dome in the outdoor environment.
The distance between the signal transmission cable and high-voltage device (or high-voltage
cable) shall be at least 50 meters.
Outdoor cable layout shall go under the penthouse if possible.
For vast land, please use sealing steel tube under the land to implement cable layout and
connects one point to the earth. Open floor cable layout is forbidden.
In area of strong thunderstorm hit or near high sensitive voltage (such as near high-voltage
transformer substation), you need to install additional high-power thunder protection device
or lightning rod.
The thunder protection and earth of the outdoor device and cable shall be considered in the
building whole thunder protection and conform to your local national or industry standard.
System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at
the same time conforms to your local electrical safety code. The earth device shall not short
circuit to N (neutral) line of high voltage power grid or mixed with other wires. When connect
the system to the earth alone, the earth resistance shall not be more than 4Ω and earth
cable cross-sectional area shall be below 25 mm². See Figure 6-1.
Figure 6-1
18
7 APPENDIX Ⅱ ABOUT RS485 BUS
7.1 RS485 Bus Main Feature
RS485 is semi duplex communication cable of impedance 120Ω. Its max load amount is 32
effective loads (including main control device and devices to be charged).
7.2 RS485 Bus Transmission Distance
When we take 0.56mm (24AWG) twisted-pair as communication cable, the max transmission
distance (theoretically) are listed below (according to different baud rates).
Max Distance
1800M
1200M
800M
Possible Reasons
In the following situations, the max transmission distance shall become shorter accordingly:
The communication cable is a little bit thin;
2400 BPS
4800 BPS
9600 BPS
The surrounding environment has strong electromagnetic interference;
There are too much devices connected to the RS485 bus;
And vice versa, the max transmission distance shall become longer.
7.3 The Problem in Practical Use
In practical usage, we usually adopt star type connection. The terminal resistance shall connect
to the furthest two devices (Such as device 1# and device 15# in Figure 7-1 ). But this connection
way does not conform to RS485 Bus standard. When the distances between devices are too
long, the signal reflection occurs and anti-jamming decreases, thus the signal reliability becomes
very low. User may see speed dome is not under control or speed dome is running automatically
and can not stop.
Figure 7-1
In this situation, we recommend RS485 distributor. This device can turn star type connection into
the connection that conforms to RS485 bus industry standard, which can avoid the above
mentioned problems and enhance communication reliability. See Figure 7-2.
19
Figure 7-2
7.4 RS485 Bus FAQ
Speed dome
can run selfdiagnosis but I
can not control
it.
I can control
the speed
dome but is not
smooth
Possible Reasons
Host address(baud rate) and
speed dome address(baud rate)
are not match;
Positive and negative end of
RS485 Bus are misconnected;
Connection cable is loose;
RS485 Bus connection are cut
off;
RS485 Bus connection are not
good;
One RS485 bus is off;
The distance between host and
speed dome is too far;
Parallel connected too much
speed domes.
20
Solution
Modify host or speed dome setup ;
Switch RS485 positive end and
negative end;
Fix connection cable firmly;
Replace RS485 Bus.
Connect RS 485 Bus again;
Replace RS485 Bus;
Add terminal matching resistance;
Add RS485 distributor.
8 APPENDIX Ⅲ SAFETY ROPE INSTALLATION
Remove one M4 screw from the speed dome and then use the M4 screw of the safety rope to fix
the safety rope on the speed dome.
Please note the contents in this chapter are for hang (pendant) mount installation only.
Safety Rope
Speed Dome M4 Screw
Speed Dome
M4 Screw of the
Safety Rope
Note
•
This manual is for reference only. Slight difference may be found in the user
interface.
•
All the designs and software here are subject to change without prior written
notice.

All trademarks and registered trademarks are the properties of their respective
owners.
•
If there is any uncertainty or controversy, please refer to the final explanation of us.
•
Please visit our website or contact your local service engineer for more
information.
21
Network Camera Web3.0 Operation Manual
Version 1.0.1
i
Table of Contents
1
2
3
4
5
Network Config ............................................................................................................................ 1
1.1
Network Connection ..................................................................................................... 1
1.2
Log in .............................................................................................................................. 1
Live ................................................................................................................................................ 6
2.1
Encode Setup ................................................................................................................ 6
2.2
System Menu ................................................................................................................. 7
2.3
Video Window Function Option .................................................................................. 7
2.4
Video Window Setup .................................................................................................... 8
2.4.1 Image Adjustment..................................................................................................... 8
2.4.2 Original Size ............................................................................................................. 9
2.4.3 Full Screen ................................................................................................................ 9
2.4.4 Width and Height Ratio .......................................................................................... 10
2.4.5 Fluency Adjustment ................................................................................................ 10
2.4.6 Rules Info ............................................................................................................... 10
2.4.7 Zoom and Focus ..................................................................................................... 10
2.4.8 Fisheye/Trigger Track ............................................................................................ 10
PTZ Control................................................................................................................................ 15
3.1
Scan .............................................................................................................................. 16
3.2
Preset ............................................................................................................................ 17
3.3
Tour ............................................................................................................................... 17
3.4
Pattern .......................................................................................................................... 18
3.5
Assistant ....................................................................................................................... 19
3.6
Light Wiper ................................................................................................................... 19
Playback ..................................................................................................................................... 20
4.1
Playback ....................................................................................................................... 20
4.1.1 Function of Play...................................................................................................... 21
4.1.2 Playback File .......................................................................................................... 22
4.1.3 Playback Cut ........................................................................................................... 24
4.1.4 Record Type ........................................................................................................... 24
4.1.5 Progress Bar ............................................................................................................ 24
4.1.6 Assistant Function .................................................................................................. 25
4.2
Picture Playback ......................................................................................................... 25
4.2.1 Play ......................................................................................................................... 26
4.2.2 Playback File .......................................................................................................... 26
4.2.3 Snapshot Type ........................................................................................................ 28
Setup ........................................................................................................................................... 30
5.1
Camera ......................................................................................................................... 30
ii
5.2
5.3
5.4
5.5
5.1.1 Conditions ............................................................................................................... 30
5.1.2 Video ...................................................................................................................... 41
5.1.3 Audio ...................................................................................................................... 53
Network......................................................................................................................... 56
5.2.1 TCP/IP .................................................................................................................... 56
5.2.2 Connection .............................................................................................................. 58
5.2.3 PPPoE ..................................................................................................................... 60
5.2.4 DDNS ..................................................................................................................... 61
5.2.5 IP filter .................................................................................................................... 62
5.2.6 SMTP (e-mail) ..................................................................................................... 63
5.2.7 UPnP ....................................................................................................................... 64
5.2.8 SNMP ..................................................................................................................... 65
5.2.9 Bonjour ................................................................................................................... 68
5.2.10 Multicast ................................................................................................................. 68
5.2.11 4G ........................................................................................................................... 69
5.2.12 WIFI........................................................................................................................ 71
5.2.13 802.1x ..................................................................................................................... 73
5.2.14 QoS ......................................................................................................................... 74
5.2.15 HTTPs ..................................................................................................................... 75
Event ............................................................................................................................. 85
5.3.1 Video detection ....................................................................................................... 85
5.3.2 Audio Detection ...................................................................................................... 92
5.3.3 Smart Plan............................................................................................................... 94
5.3.4 Intelligence Behavior Analytics ............................................................................. 94
5.3.5 Face Detection ...................................................................................................... 102
5.3.6 People Counting ................................................................................................... 104
5.3.7 Heat Map .............................................................................................................. 106
5.3.8 Alarm .................................................................................................................... 109
5.3.9 Abnormity............................................................................................................. 113
Storage Management ............................................................................................... 116
5.4.1 Schedule................................................................................................................ 116
5.4.2 Destination ............................................................................................................ 120
5.4.3 Record control ...................................................................................................... 122
System ........................................................................................................................ 123
5.5.1 General.................................................................................................................. 123
5.5.2 Account ................................................................................................................. 126
5.5.3 PTZ ....................................................................................................................... 129
5.5.4 Default .................................................................................................................. 130
5.5.5 Import/Export ....................................................................................................... 131
iii
6
7
5.5.6 Remote control ........................................................................................................ 131
5.5.6 Auto Maintenance................................................................................................. 132
5.5.7 Upgrade ................................................................................................................ 133
5.6
Information ................................................................................................................. 133
5.6.1 Version.................................................................................................................. 133
5.6.2 Log ........................................................................................................................ 134
5.6.3 Online User ........................................................................................................... 134
Alarm ......................................................................................................................................... 136
Log out ...................................................................................................................................... 138
iv
Important
The following functions are for reference only. Some series products may not
support all the functions listed below.
v
1 Network Config
1.1 Network Connection
Network camera and PC connection mainly has two ways, see Figure 1- 1 and Figure 1-2.
Figure 1- 1
Figure 1-2
Before you access network camera via the Internet, you need to have its IP address. User can use
Config Tool to search IP of the network camera. Please refer to Config Tool manual.
1.2 Log in
It needs to install WEB plug-in when you use WEB client for the first time, the exact operation steps are
shown as follows:
Open IE and input network camera address in the address bar. (The factory default IP address is
192.168.1.108).
1
After successful connection, the login interface is shown as in Figure 1-3; input your user name and
password. Default factory username is admin and password is admin.
Figure 1-3
The system will display “Update Password” prompt box for your first login, users need to modify the
password and save it properly.
Figure 1-4
After successful login, you may see the interface shown as in Figure 1-5.
2
Figure 1-5
Click on “Please click here to download and install the plug-in”. The system pops up warning information
to ask you whether run or save this plug-in. See Figure 1-6.
Figure 1-6
3
You must either run or save the file to local and install it. Follow the following steps. Click on run, you
will see Figure 1-7and Figure 1-8.
Figure 1-7
4
Figure 1-8
When plug-in installation completes, the installation page closes automatically. The web-end will refresh
automatically, and then user may view video captured by the camera.
Figure 1-9
5
2 Live
After you logged in, user may see the live monitor window. See Figure 2-1.
2
1
3
4
Figure 2-1
There are four sections:
Section 1: Encode setup bar
Section 2: System menu
Section 3: Window function option bar
Section 4: Window adjust bar
2.1 Encode Setup
Note: Some series don’t support sub stream 2.
The encode setup interface is shown as in Figure 2-2.
Figure 2-2
Please refer to the following sheet for detailed information.
6
Parameter
Function
Main stream
Click it to enable main stream video monitoring and click again
to disable it. Generally for storage and monitor.
Click it to enable Sub Stream 1 video monitoring and click again
to disable it. When network bandwidth is insufficient, it
substitutes main stream for monitoring.
Click it to enable Sub Stream 2 video monitoring and click again
to disable it. When network bandwidth is insufficient, it
substitutes main stream for monitoring.
User may select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
Sub Stream 1
Sub Stream 2
Protocol
2.2 System Menu
System menu is shown as in Figure 2-3.
Please refer to chapter 2 Live, chapter 3 PTZ, chapter 4 Playback, chapter 5 Setup, chapter 6 Alarm,
chapter 7 Log out for detailed information.
Figure 2-3
2.3 Video Window Function Option
The interface is shown as below. See Figure 2-4.
1
2
3
4
5
6
7
8
9
Figure 2-4
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1
Relay-out
It shows if there is any alarm output, status description is as
follows:
Red: means there is alarm output.
Grey: means alarm is over.
Click on the button to force alarm to be on or off.
7
When the video is in the original status, click it user may
select any zone to zoom in. In the non-original status,
user may drag the zoom-in zone in specified range. Right
click mouse to restore previous status.
Click it; user may use the middle button of the mouse to
zoom in/out the video size.
Click on the button to snapshot, save picture to path in Ch.
5.1.2.5.
2
Digital
Zoom
3
Snapshot
4
Triple
snapshot
Click it to take snapshot upon the video at the frequency of
one picture per second. All images are saved to path in Ch
5.1.2.5.
5
Record
Click it to record the video. All videos are saved to path in
Chapter 5.1.2.5.
6
Easy focus
Click it, user may see there are two parameters on the
preview video:AF Peak and AF Max.
AF Peak: It is to display the video definition during the focus
process.
AF Max: It is the most suitable value for the video definition.
The close the AF Peak and AF Max is, the better the focus
effect is.
7
Audio
Turn on or off audio when you are monitoring.
8
Talk
Click it to start or end bidirectional talk.
9
Help
Click it to open help file.
2.4 Video Window Setup
The interface is shown as in Figure 2-5.
Figure 2-5
2.4.1 Image Adjustment
See Figure 2-6 for image adjustment.
8
Figure 2-6
Click this button to display/hide image control interface. Click it to open picture setup interface. This
interface is on the top right pane.
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
It is to adjust monitor video
brightness.
It is to adjust monitor video
contrastness.
It is to adjust monitor video
hue.
Note:
All the operations here apply
to WEB end only.
Please go to Setup>Camera->Conditions to
adjust corresponding items.
It is to adjust monitor video
saturation.
Reset
Restore brightness,
contrastness saturation and
hue to system default setup.
2.4.2 Original Size
Click this button to go to original size. It is to display the actual size of the video stream. It depends on
the resolution of the bit stream.
2.4.3 Full Screen
Click it to go to full-screen mode. Double click the mouse or click the Esc button to exit the full screen.
9
2.4.4 Width and Height Ratio
Click it to restore original ratio or suitable window.
2.4.5 Fluency Adjustment
There are three levels of fluency for you to select (Realtime, Normal, and Fluency). The default is
normal.
2.4.6 Rules Info
Click the button, preview image will display intelligent rules after enabling; it is “enable” by default.
2.4.7 Zoom and Focus
Click this button and the focus zooming interface appears on the right of preview interface, as shown in
Figure 2-7, click left mouse button to adjust focus zooming configuration.
Note:
· The product series which support motorized zoom, synchronous focus and back focus have this
button.
· Auto-focus after zoom and focus adjustment.
2.4.8 Fisheye/Trigger Track
Click the button, installation mode and display mode interface will show up on the right of the preview
interface, see Figure 2-8 and Figure 2-9, single click to switch different installation modes and display
modes for fisheye, or switch different display modes for trigger track, it is enabled by default.
Note:
It is only supported by some models.
Figure 2-7
10
Parameter
Zoom
Focus
Autofocus
Function
Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons.
The speed is used to adjust the length of one step during single click.
Adjust the sharpness of the lens by clicking or long pressing“+”、“-” buttons.
Step length is used to adjust the length of one step with one click.
Click to adjust the image definition automatically.
Note:
Other lens operations are not allowed during the process of auto-focus.
Reset the lens to zero position to eliminate the accumulative error of lens.
Reset All
Note:
Please reset when the image adjustment is not clear or operating zoom focus many
times.
Refresh
Synchronize the location of drag slider of lens and zoom focus after hardware zoom
focusing.
Regional
Focus
Click it and use the mouse to select a zone, then the device can auto focus within the
specific region.
In-ceiling Mount
Wall Mount
Ground Mount
11
Figure 2-8
parameter
Note
Installation Mode
Three modes which are ceiling mount, wall mount and ground mount.
It represents the display mode of the current image (default supports original
image mode), the display modes may be different according to different
installation modes. It is shown as follows:
Ceiling: 1P+1、2P、1+2、1+3、1+4、1P+6、1+8。
Display Mode
Wall: 1P、1P+3、1P+4、1P+8。
Ground: 1P+1、2P、1+3、1+4、1P+6、1+8。
Note:
The default displays original image mode when switching installation mode.
In-ceiling/Wall/Ground
Original
It menas the original image without de-warpping
image
360°expanded rectangular panorama + independent
sub image, the sub image and the subbox in the
expanded rectangular panorama support zoom and
movement, for the expanded rectangular panorama
also supports left and right starting point movement.
1P+1
2P
In-ceiling/Ground
1+2
1+3
1+4
Two related 180° expanded rectangular pictures, two
subwindows form 360° panorama anytime, which is
also called “dual panorama”. Two expanded
rectangular pictures both support left and right
movement starting point, which are also linked by
eachother.
Original image + 2 independent sub images, both the
sub image and the subbox in the original image
support zoom and movement. The original image also
supports changing starting point by rotation (no such
display mode for ground installation).
Original image + 2 independent sub images, both the
sub image and the subbox in the original image
support zoom and movement. The original image also
supports changing starting point by rotation
Original image + 4 independent sub images, both the
sub image and the subbox in the original image
support zoom and movement. The original image also
supports changing starting point by rotation
12
parameter
Note
360°expanded rectangular panorama +6 independent
sub image, both the sub image and the subbox in the
expanded rectangular panorama support zoom and
movement, for the expanded rectangular panorama
also supports left and right starting point movement.
Original image + 8 independent sub images, both the
sub image and the subbox in the original image
support zoom and movement. The original image also
supports changing starting point by rotation
1P+6
1+8
From left to right 180° expanded rectangular
panorama, which supports up and down movement
and changes vertical angle of view.
1P
1P+3
Wall
1P+4
1P+8
180° expanded rectangular panorama+3 independent
sub images, both the sub images and the sub box in
the expanded rectangular panorama support zoom
and movement, expanded rectangular panorama
supports up and down movement and changes vertical
angle of view.
180° expanded rectangular panorama+4 independent
sub images, both the sub images and the sub box in
the expanded rectangular panorama support zoom
and movement, expanded rectangular panorama
supports up and down movement and changes vertical
angle of view.
180° expanded rectangular panorama+8 independent
sub images, both the sub images and the sub box in
the expanded rectangular panorama support zoom
and movement, expanded rectangular panorama
supports up and down movement and changes vertical
angle of view.
Figure 2-9
Enable the trigger track on the interface of tripwire or intrusion, and draw the rule of tripwire or intrusion,
the scene of trigger track window will change according to the moving object when it triggers rule alarm
until the moving object disappears from the view range of the camera. Please refer to “5.3.4 IVS” for
more details about the rules drawing and parameter config of tripwire and intrusion.
Trigger track includes three modes which are 1P, 1P+3 and 1P+5.
13
1P: Original picture
1P+3: Original picture and three trigger track windows, it can adjust the location and size of
three trigger track windows on the original picture.
1P+5: Original picture and five trigger track windows, it can adjust the location and size of
five trigger track windows on the original picture.
14
3 PTZ Control
Here user may view direction keys, speed, zoom, focus, iris, preset, tour, pan, scan, pattern, aux on, off
and PTZ setup button. See Figure 3-1.
Note:
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to Ch. 5.5.3).
Currently only IPC-HFXXXX series and –PT series products can support PTZ function.
Parameter
PTZ direction
Speed
Quick Position
Note
PTZ supports eight directions: left/right/up/down/upper left/upper
right/bottom left/bottom right.
It controls rotation speed. The longer the step length, the higher the speed.
Step length control PTZ, zoom, focus and iris.
Use mouse to draw a box in monitoring video, PTZ will rotate and focus to
quickly positioning.
Figure 3-1
15
Figure 3-2
PTZ setting interface is shown as in Figure 3-3.
Here user may set scan, preset, tour, pattern, assistant function and light and wiper plus view
coordinate.
Figure 3-3
3.1 Scan
Scan interface is shown in Figure 3-4.
16
Figure 3-4
Steps to scan are:
Step 1. Click on Set button, display
icon.
Step 2. Move via direction key to select left, click on Set Left to set left border of camera
Step 3. Move via direction key to select right, click on Set Right to set right border of camera.
Step 4. Complete scan path setup.
3.2 Preset
Preset interface is shown in Figure 3-5.
Figure 3-5
Steps to preset are:
Step 1. In preset box, input preset value.
Step 2. Click on Go to, camera rotates to preset position.
Step 3. Use direction key to rotate camera, and in preset box input preset value.
Step 4. Click on Add to add a preset. Range of preset relates to PTZ protocol.
3.3 Tour
17
Tour interface is shown in Figure 3-6.
Figure 3-6
Steps to tour are:
Step 1. In tour box, input tour path value.
Step 2. Click on Add. Range of tour relates to PTZ protocol.
Step 3. In preset box, input preset value.
Step 4. Click on Add as to add a preset in this tour. If click on Del, it deletes this preset in tour.
Note:
User may add more than one preset here, or delete more than one preset.
3.4 Pattern
Pattern interface is shown in Figure 3-7.
Figure 3-7
Steps to set pattern are shown as follows:
Step 1
Input pattern serial number value in the box, click “Add” and it will display “Start Rec” and “Stop Rec”.
Step 2
Click “Start Rec” to implement a series of operations such as zoom, focus, iris, direction and so on.
Step 3
18
Click “Stop Rec” to complete the setting of a pattern path.
Step 4
Click “Start” and it will start pattern according to the pattern path which has been set; click “Stop” and
the pattern ends.
3.5 Assistant
Assistant interface is shown in Figure 3-8.
Figure 3-8
Steps to assistant are:
Step 1. In assistant box input assistant value.
Step 2. Click on Aux On to turn on aux function.
Click on Aux off to turn off aux function.
3.6 Light/ Wiper
Light wiper interface is shown in Figure 3-9.
Figure 3-9
Steps to light wiper are:
Click on Enable to enable light wiper function.
Click on Disable to disable light wiper function.
19
4 Playback
Web client playback supports video playback and picture playback.
Note:
Before playback, user shall set storage management as in Ch. 5.4.
4.1 Playback
The playback interface is shown as in Figure 4-.
6
2
1
3
4
5
Figure 4-1
There are four sections:
Section 1: Function of play
Section 2: Playback file
Section 3: Play time cut
Section 4: Record type
Section 5: Progress bar
Section 6: Assistant function
20
4.1.1 Function of Play
The function of play is shown as in Figure 4-2 and Figure 4-3.
Figure 4-2
Figure 4-3
Parameter
Function
①
Play
When you see this button, it means pause or not played record. Click on this
button, switch to normal play status.
②
Stop
Click this button to stop playing.
③
Play
frame
by
Click on this button to go to next frame.
Note:
You shall pause record when you use this function.
④
Slow
Click on this button to play slowly.
⑤
Quick
Click on this button to play quickly.
⑥
Silent
When this button displays, it means audio is silent. Click on this button to switch
back to normal.
⑦
Volume
Click on left mouse to adjust volume.
⑧
-1 Fisheye
Click this button and fisheye device can adjust display mode according to
different installation mode during the process of playback.
⑧ -2 Rule Info
Click the button and it will playback and display intelligent rules and object
detection box if the video is equipped with intelligent rule info after the function is
enabled, it is off by default.
21
4.1.2 Playback File
In calendar, blue date represents data currently has video record or snapshot. See Figure 4-4.
Figure 4-4
Parameter
File Type
Data Source
Function
Select “dav”, as video playback.
Select “jpg” as picture playback.
Default is SD card.
Step 1. Click on data in blue, time axis displays record file progress bar in color. While, green represents
normal record, yellow represents motion detect record, red represents alarm record, and blue
represents manual record.
Step 2. Click on certain time on progress bar, playback starts from this time. See Figure 4-5.
Figure 4-5
Step 3. Click on file list
, select date file will be displayed in list.
Step 4. Double click on file in list, playback this file and display file size, start time and end time.
See Figure 4-6.
22
Figure 4-6
Parameter
Search
Record Format
Function
It means records within searched start time and end time on the date.
There are two formats: dav, mp4.
Click the download button and download file to path in Ch. 5.1.2.5.
Download
System does not support download and playback at the same time.
23
Parameter
Back
Function
Click on back button to go to calendar interface.
4.1.3 Playback Cut
Note:
Playback cut function will automatically pause playing record as playback cut and playback cannot be at
the same time.
Step 1. Click on start time to cut on time axis. This time must be within progress bar range.
Step 2. Move mouse to cut icon
. You will be ask to select start time. Click on cur icon
as
finish cutting.
Step 3. Click on playback cut end time on time axis. This time must be within progress bar range.
Step 4. Move mouse to cut icon
you will be asked to select end time. Click on cut icon
as
finish cutting.
Step 5. Click on Save button to save file cut to path in Ch 5.1.2.5. See Figure 4-7.
Figure 4-7
4.1.4 Record Type
After checking record file type, only selected file will be displayed in progress bar and file list. Users can
also select the record type to be displayed via the dropdown box which is above the file list. See Figure
4-8.
Figure 4-8
4.1.5 Progress Bar
24
Figure 4-9
Parameter
Function
24 hours
Click on it, means video in past 24 hours.
2 hours
Click on it, means video in past 2 hours.
1 hour
Click on it, means video in past 1 hour.
30 min
Click on it, means video in past 30 min.
4.1.6 Assistant Function
Video playback assistant function is shown in Figure 4-10.
Figure 4-10
Parameter
Function
Click on it, video in playback status if is in original size, user can
zoom in any area, If it is not in its original size, right click mouse to
restore its original size.
Digital Zoom
Click on this button, user may scroll to zoom in.
Click on this button, user may snapshot video under playback status.
Snapshot will be saved to path in Ch. 5.1.2.5.
Snapshot
4.2 Picture Playback
Web client picture playback interface has the following three functions:
Parameter
Function
1
Play function bar
2
Playback file bar
3
Snapshot type bar
See Figure 4-11.
25
Figure 4-11
4.2.1 Play
Figure 4-12
Default icon is
and it means pause or not played picture. Click on play button to switch to
normal play status. Icon become
Click on it to pause.
4.2.2 Playback File
26
Figure 4-13
Step 1. Click on file list
, select snapshot file of the date.
Step 2. Double click on file in list, to play this snapshot.
Parameter
Search
Function
It means all snapshot files within the start time and end time of selected date.
27
Parameter
Download
Back
Function
Click the download button to open snapshot file or directly download to local
according to the browser types.
Click on back button to return to calendar interface and re-select time.
Figure 4-14
4.2.3 Snapshot Type
28
After checking snapshot file type, in file list only display file of selected type. Users can also select the
snapshot type to be displayed via the dropdown box above the file list. See Figure 4-.
Figure 4-15
29
5 Setup
Web client setup support camera, network, time, storage, system and system info view.
5.1 Camera
The camera setting includes conditions, profile management, zoom and focus.
5.1.1 Conditions
Note:
The camera parameter may be different according to different models, please refer to the actual product
for more details.
5.1.1.1 Picture
Note:
The device which supports true WDR fails to support long exposure when true WDR is enabled.
Step 1
Select “Setup > Camera > Conditions > Picture” and the system will display the “Picture” image which is
shown in Figure 5-1.
Figure 5-1
Step 2
Set picture parameters; please refer to the following sheet for more details about parameter setting.
Parameter
Note
Style
It is to set the picture style, which includes standard, soft and vivid.
30
Parameter
Note
It is to adjust the image overall brightness via linear adjustment mode.
Brightness
The larger the number is, the brighter the picture is, and on the contrary it
is opposite. The picture get blurry easily when the value is set too big.
Contrast
It is to adjust the picture contrast. The bigger the value is, the bigger the
bright contrast becomes, and on the contrary it is smaller. The dark area
becomes darker and the bright area becomes overexposed easily when
the value is set too big. The picture becomes blurry when the value is set
too small.
Saturation
It is to adjust the color darkness and lightness. The color becomes darker
when the value is bigger; on the contrary it becomes lighter. The value
causes no influence to the overall brightness of the image.
Sharpness
It is to adjust the sharpness level of the picture edge. The bigger the
sharpness value is, the more obvious the image edge becomes, the image
is likely to generate noise more easily when the value is set too big.
Gamma
It is to change image brightness and improve the dynamic display range of
the image via nonlinear adjustment mode. The bigger the value is, the
brighter the picture becomes, and on the contrary it is opposite.
Mirror
After mirror is enabled, the monitoring image will be displayed invertedly.
It is to change the display direction of the monitoring image.
It includes following options:
Normal: The monitoring picture is normally displayed.
Flip mode 1: The monitoring picture is displayed with clockwise
rotation 90°
Flip
Flip mode 2: The monitoring picture is displayed with anticlockwise
rotation 90°
180°: The monitoring picture is displayed upside down.
Note:
Please set the video resolution as 1080P or lower when applying flip mode
for some devices.
EIS
It can realize electronic anti-flicker function via comparison algorithm of
image difference, which can effectively solve the problem of image jittering
during application and it can make the image clearer.
Step 3
Click “Save” and complete the image parameter config of the camera.
31
5.1.1.2 Exposure
Step 1
Select “Setup > Camera > Conditions > Exposure”. The system will display the “Exposure” interface
which is shown in Figure 5-2.
Figure 5-2
Step 2
It is to set the exposure parameter, please refer to the following sheet for more details.
Parameter
Note
Outdoor: User may switch to exposure mode when it is in
outdoor mode, it can realize the result in the corresponding
exposure mode.
Anti-flicker
50Hz: When the current is 50Hz, system can auto adjust the
exposure according to the environment brightness in case
there is any stripe.
60Hz: When the current is 60Hz, system can auto adjust the
exposure according to the environment brightness in case
there is any stripe.
32
Parameter
Note
It is the camera exposure mode.
Note:
When “Anti-flicker” is “Outdor”, the “exposure mode” can be
set as “gain priority” or “shutter priority” mode.
Different devices have different exposure modes; please
refer to the actual interface.
It includes the following options:
Auto: It can auto adjust the image brightness according to
the environment.
Mode
Gain priority: The device can auto adjust according to the
gain range which is set by priority during normal exposure
range according to the different scene brightness. The device
will auto adjust shutter value if the image brightness fails to
reach the effect and the gain value has reached to upper limit
or lower limit, which is to make the image reach the best
brightness.
Shutter priority: The device can auto adjust according to the
shutter range which is set by priority during normal exposure
range according to the different scene brightness. The device
will auto adjust shutter value if the image brightness fails to
reach the effect and the shutter value has reached to upper
limit or lower limit, which is to make the image reach the best
brightness.
Iris priority: Iris value is fixed, the device can auto adjust the
shutter value if the image brightness fails to reach effect and
the shutter value has reached the upper limit or lower limit,
the device can auto adjust the gain value to make the image
reach the best brightness.
Manual: It is to manually set gain value and shutter value,
adjust the the displayed brightness of the image.
It can set the parameter when the camera installs auto iris.
Auto Iris
The lens iris can auto adjust the size according to the
environment after auto iris is enabled, then the image
brightness will change accordingly.
The iris value reaches the max when disabling auto iris, the
lens iris will not change according to the environment
brightness.
3D NR
Grade
It is to process the image with multiframe (at least two frames), it
can realize noise reduction of the image by using the interframe
information between the previous and latter frame.
It can set the parameter when “3D NR” is enabled.
The bigger the grade is, the better NR effect it can realize.
33
Step 3
Click “Save” to complete the parameter config of camera exposure.
5.1.1.3 Backlight
Backlight mode can be divided into BLC, WDR and HLS.
BLC: it can avoid cucoloris phenomenon of the darker area in the backlight environment.
WDR: It can suppress the overbright area and compensate darker area by enabling WDR, which can
make the overall image clear.
HLC: It is to weaken the high light, which can be applied in the areas such as toll gate, entrance and exit
of the parking lot and etc. As for extreme light, it can snapshot the human face in the dark environment
and it can realize better effect for the details of the plate number.
Step 1
Select “Setup > Camera > Condition > Backlight”, the system will display the interface of “Backlight”
which is shown in Figure 5-3.
Figure 5-3
Step 2
Set the backlight parameter.
When the “Mode” is set as “Scene Self-adaptation”, the system will auto adjust the image
brightness according to the environmental brightness, which is to make the object display clearly in
the scene.
When the “Mode” is set as “BLC”, it can select default mode or customized mode.
When selecting “Default” mode, the system can realize auto exposure according to the
environment, which is to make the image in the darkest area clear to be seen.
34
When selecting “Customized” mode, the system can realize exposure upon the selected area
after it set customized area, which is to make the image of the selected area reach
appropriate brightness.
When the “Mode” is set as “WDR”, it will lower the brightness of the area with high brightness and
enhance the brightness of the area with low brightness, which is to make the objects in both high
brightness and low brightness area display clearly.
Note:
There may be video loss of a few seconds when the camera is switched from non WDR mode to WDR
mode.
When the “Mode” is set as “HLC”, the system will constrain the brightness of the area with high
brightness and decrease the size of the halo area, which is to lower the brightness of the whole
image.
Step 3
Click “Save” to complete the config of the backlight mode.
5.1.1.4 WB
WB is used to restore the white object in the scene by the camera, after WB mode is set, it can make
the white object look white in different environments.
Step 1
Select “Setup > Camera > Conditions > WB”, the system will display the interface of “WB”, which is
shown in Figure 5-4.
Figure 5-4
Step 2
Set WB mode.
35
When the “Mode” is set as “Auto”, the system can auto compensate white balance upon different
color temperatures, which is to make the image color normal.
When the “Mode” is set as “Natural”, the system can auto compensate white balance to the scene
without artificial light, which is to make the image color normal.
When the “Mode” is set as “Street Lamp”, the system can auto compensate white balance to the
outdoor scene at night, which is to make the image color normal.
When the “Mode” is set as “Outdoor”, the system can auto compensate white balance to the most
outdoor scenes with natural light and artificial light, which is to make the image color normal.
When the “Mode” is set as “Manual”, it can manually set the value of red gain and blue gain; the
system can compensate the different color temperatures in the environment according to the
settings.
When the “Mode” is set as “Regional Custom”, it is to set customized area, the system can
compensate white balance to different color temperature of the images in the area, which is to
make the image color normal.
Step 3
Click “Save” to complete the config of WB mode.
5.1.1.5 Day & Night
It is to set the switch between color mode and black & white mode.
Step 1
Select “Setup > Camera > Conditions > Day & Night” and the system will display the interface of “Day &
Night”, which is shown in Figure 5-5.
Figure 5-5
36
Step 2
Set day & night parameter; please refer to the following sheet for more details.
Parameter
Mode
Sensitivity
Delay
Note
It is to set the camera image displayed as color or black & white mode.
Note:
The setting of “Day/Night Mode” is not affected by the setting of “Profile
Management”.
It includes the following options:
Color: The camera image is displayed as color image.
Auto: The camera can auto select color image or black & white image
to be displayed according to the environmental brightness.
Black & white: The camera image is displayed as black & white image.
The parameter can be set when the “Day/Night Mode” is “Auto”.
It is to set the sensitivity of the switch between image color display and
black & white display.
The parameter can be set when the “Day/Night Mode” is “Auto”.
It is to set the switch delay between image color display and white & black
display. The smaller the delay is, the faster of the switch becomes between
color display and black & white display.
Step 3
Click “Save” to complete the config of day/night mode.
5.1.1.6 Defog
The image quality will become weak when the device is in the environment with fog or haze, user may
enable defog function to adjust the image definition.
Step 1
Select “Setup > Camera > Conditions > Defog” and the system will display the interface of “Defog”
which is shown in Figure 5-6.
37
Figure 5-6
Step 2
It is to set defog mode according to the actual scene.
When the “Mode” is set as “Manual”, it is to manually set intensity and air light mode, the system
will adjust the image definition according to the intensity and air light mode which have been set
previously. As for air light mode, user may set manual or auto.
When the “Mode” is set as “Auto”, the system will auto adjust the image definition according to the
actual scene.
When the “Mode” is set as “Off”, then the defog function is disabled.
Step 3
Click “Save” to complete the config of defog mode.
5.1.1.7 IR Light
User may directly set the mode of IR light if the device is equipped with IR light.
Step 1
Select “Setup > Camera > Conditions > IR Light” and the system will display the interface of “IR Light”
which is shown in Figure 5-7.
38
Figure 5-7
Step 2
It is to set IR light mode according to the actual scene.
When the “Mode” is set as “Manual”, it can manually set the brightness of IR light; the system will
realize light compensation to the image according to the IR light intensity.
When the “Mode” is set as “Smart IR”, the system can adjust the light brightness according to the
actual scene.
When the “Mode” is set as “Zoomprio”, the system can auto adjust the IR light according to the
brightness change of the actual scene.
The system will enable near light by priority when the actual scene becomes dark, the system
will enable the far light when the near light fails to meet the requirement of scene brightness
even if it is adjusted to the brightest.
The system will adjust far light brightness by priority to off and then adjust the brightness of
near light when the actual scene becomes bright. The system will always disable far light
when the focal length of the lens is adjusted to a certain wide angle, which is to avoid near
overexposure. Meanwhile, it can manually set light compensation to slightly adjust the
brightness of IR light.
When the “mode” is set as “Off”, it will not enable the IR light.
Step 3
Click “Save” and complete the config of IR light.
5.1.1.8 Profile Management
Step 1
Select “Setup > Camera > Conditions > Profile Management” and the system will display the interface of
“Profile Management”.
39
Step 2
Set profile management.
When the “Profile Management” is set as “Normal”, the system will monitor according to the normal
config.
Figure 5-8
When the “Profile Management” is set as “Full Time”, user may select “Always Enable” in “Day” or
“Night’, the system will monitor according to the config of “always enable”.
Figure 5-9
When the “Profile Management” is set as “Schedule”, user may set some period as day and
another period as night, for example, if it sets 0:00~12:00 as day, 12:00~24:00 as night, then the
system will monitor by adopting corresponding config in different periods.
Figure 5-10
Step 3
Click “Save” to complete the settings of profile management.
Note:
Click “Default” to restore the device to default config; click “Refresh” to check the latest config file of the
device.
40
5.1.1.9 Zoom and Focus
Note:
Only motorized vari-focal devices support focus and zoom function.
Step 1
Select “Setup > Camera > Conditions > Zoom and Focus” and the system will display the interface of
“Zoom and Focus” which is shown in Figure 5-11.
Figure 5-11
Step 2
Adjust the focal length of the lens.
After it is zoomed, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust.
Step 3
Adjust the lens definition.
After it is focused, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust.
Note:
Speed is used to set the length by pressing “+” and “-“.
After adjusting the focal length of the lens or click “Auto Focus”, the device will auto adjust the
image definition, it is not allowed to implement other lens operation during auto focus.
After several times of zoom and focus, the image fails to be adjusted clear, click “Restore All’ to
reset the lens to zero and remove the accumulative error of the lens.
Click “Refresh” and the device will automatically synchronize the hardware to the location of sliding
block of lens zoom and focus.
5.1.2 Video
41
5.1.2.1 Video
Step 1
Select “Setup > Camera > Video > Video” and the system will display the interface of “Video” which is
shown in Figure 5-12 or Figure 5-13.
Figure 5-12 (Non fisheye)
Figure 5-13 (Fisheye)
Step 2
42
Set video bit stream, please refer to the following sheet for more details about the parameters.
Parameter
Installation Mode
Record Mode
Function
It will display the parameter when the device is fisheye.
There are three installation modes for fisheye which are
ceiling, wall mount and ground installation, please
select installation mode according to the actual
installation scene of the fisheye.
The system will begin to switch after switching
installation mode, it will prompt successfully saved after
it is switched successfully.
Note:
The device end will output the dewarped video stream
after configuring installation and record mode, when the
device is accessed to third-party platform, it will directly
display the dewarped image on the third-party platform.
It will display the parameter when the device is fisheye.
The system will begin to switch after record mode is
switched, it will prompt saved successfully after it is
switched successfully.
The record mode will change according to the different
installation modes.
1O: the original picture which is not dewarped.
1P: 360°rectangular panorama.
2P: The mode can be set when the “Installation
Mode” is set as “Ceiling” or “Ground”. It is the 2
related 180°rectangular image, the two
subwindows can both form 360°panorama anytime.
1O+3R: original image + 3 independent sub
images, both the sub image and sub boxes in the
original image can support zoom and movement.
1R: Original image + independent sub image, the
sub boxes of the original image support zoom and
movement.
4R: original image + 4 independent sub images,
both the sub image and sub boxes in the original
image support zoom and movement.
2R: Original image + 2 independent sub images,
the sub boxes of the original image can support
zoom and movement, the sub image supports up
and down movement, which can change the
vertical angle of view.
Note:
The device end will output dewarped video stream after
configuring installation and record mode, when the
device is accessed to the third-party platform, it will
directly display the dewarped image on the third-party
platform.
43
Parameter
Sub Stream Enable
Smart Codec
Code-Stream Type
Encode mode
Resolution
Function
Select “Enable” to enable sub stream.
The device supports enabling sub stream 1 and sub
stream 2 at the same time.
It can enhance image compression performance and
reduce storage space by enabling intelligent encoding.
Note:
After intelligent encoding is enabled, the device will not
support third stream, ROI or intelligent event detection,
please refer to the actual interface for more details.
ACF means using different fps to record.
There are two options: VBR and CBR.
Please note user may set video quality in VBR mode.
Note:
WEB interfaces don’t support motion detect and alarm
code stream setting.
There are five options: H.264 (main profile standard,
H.264H (high profile standard), H.264B (Baseline
Profile), H.265 (main profile standard) and MJPEG
encode.
The H.264, H.264H both are H264 bit stream.
H.264 is the Main Profile encode and you need to
enable the sub stream function in your camera and
set the resolution as CIF. Then user may monitor
via the Blackberry cell phone.
The H.265 is the main profile encode mode.
MJPEG: In this encode mode, the video needs to
large bit stream to guarantee the video definition.
User may use the max bit stream value in the
recommend bit to get the better video output effect.
There are multiple resolutions. User may select from the
dropdown list.
For each resolution, the recommended bit stream value
is different.
Note: When video is under rotating status, user maynot
set resolution higher than 1080P (excluding 1080P).
Video Clip
The function is only supported by sub stream 2, please
refer to “Video Clip” for more details below the sheet.
Frame Rate (FPS)
PAL: 1~25f/s,1-50f/s NTSC: 1~30f/s or 1~60f/s.
The frame rate may vary due to different resolutions.
Bit Rate Type
There are two options: VBR and CBR.
Please note, user may set video quality in VBR mode.
Under MJPEG mode, only CBR is available.
Recommended Bit
Recommended bit rate value according to the resolution
and frame rate you have set.
44
Parameter
Function
In CBR, the bit rate here is the max value. In
dynamic video, system needs to low frame rate or
video quality to guarantee the value.
The value is null in VBR mode.
Please refer to recommend bit rate for the detailed
information.
Bit Rate
SVC
Frame rate can be encoded by layer. It is a flexible
encoding method. By default, it is 1 as 1 layer. You also
can set 2/3/4 layers.
I Frame
Here user may set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50.
Recommended value is frame rate *2.
Watermark Settings
Select “Watermark Setting” and enable watermark
function. After the watermark function is enabled, user
may check if the video is tampered via verifying
watermark character.
Watermark Character
It is the character of watermark verification, it is
DigitalCCTV by default.
Video Clip
1. Select “Sub Stream 2” in the drop-down box, click “Enable”.
2. Enable “Video Clip”, click
.
The system will display the interface of “Area”, which is shown in Figure 5-14.
45
Figure 5-14
3. Select the needed resolution and clip the needed image on the interface, which is shown in Figure
5-15.
4. Click “Save”. User may check the clipped video in the preview interface (the sub stream 2 preview
interface only displays the clipped area), which is shown in Figure 5-15.
46
Figure 5-15
Step 3
Click “Save” to complete video stream setup.
5.1.2.2 Snapshot
The snapshot interface is shown as in Figure 5-16.
Figure 5-16
Please refer to the following sheet for detailed information.
47
Parameter
Function
Snapshot type
There are two modes: general (schedule) and Event (activation).
Image size
It is the same as the resolution of main stream.
Quality
It is to set the image quality. There are six levels.
Interval
It is to set snapshot frequency. Optional1~7s/picture, customized.
5.1.2.3 Video Overlay
The video overlay interface is shown as in Figure 5-17.
Figure 5-17
48
Figure 5-18
Figure 5-19
49
Figure 5-20
Figure 5-21
50
Figure 5-22
Please refer to the following sheet for detailed information.
Parameter
Function
Privacy Masking
Here user may privacy mask the specified video in the
monitor video.
System max supports 4 privacy mask zones.
User may enable this function so that system overlays time
information in video window.
User may use the mouse to drag the time tile position.
User may enable this function so that system overlays
channel information in video window.
User may use the mouse to drag the channel tile position.
User may enable this function to overlay text in video
window.
User may use the mouse to drag location box to adjust its
position. Alignment include align left and align right.
User may enable this function to display overlay picture.
Click on disable to turn it off.
Click on Upload Picture to overlay local picture into
monitoring window. User may drag the yellow box to move
it.
Note:
User maynot enable text and picture overlay at the same time.
Check “Enable” to display the counting statistics data in
the video monitoring window; check “Disable” not to
display.
There are enter number and leave number for statistics
type and left align and right align for OSD info.
Time Title
Channel Title
Text Overlay
Picture Overlay
Counting
51
Default
Set privacy mask, channel title, time title, location, overlay
and save the change. User may click on Refresh to see
effect.
Click it to restore default config.
Save
Click it to complete video settings.
Refresh
5.1.2.4 ROI
Note: Some series don’t support ROI setup function.
Figure 5-23
52
Figure 5-24
Parameters
Enable
Note
Check “Enable”, then it will display the ROI in the video monitoring window;
Check “Disable”, then it won’t display.
Set the image quality of ROI, ranging from 1~6, default is 6.
Image
Quality
Note:
For fisheye device, it ranges from 1~6 (best), default is 6 (best)
Able to set area block, max 4 areas.
5.1.2.5 Path
The storage path interface is shown as in Figure 5-25.
Here user may set snap image saved path and the record storage path.
The default monitor image path is C:\Users\admin\WebDownload\LiveSnapshot.
The default monitor record path is C:\Users\admin\WebDownload\LiveRecord.
The default playback snapshot path is C:\Users\admin\WebDownload\PlaybackSnapshot.
The default playback download path is C:\Users\admin\WebDownload\PlaybackRecord.
The default playback cut path is: C:\Users\admin\WebDownload\VideoClips.
Note:
Admin is locally logged in PC account.
Please click the Save button to save current setup.
Figure 5-25
5.1.3 Audio
Please note some series devices do not support audio function.
5.1.3.1 Audio
The audio interface is shown as below. See Figure 5-26.
53
Figure 5-26
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
User may enable audio only when video is enabled.
After selecting the “Enable” of main stream or sub stream, the
network transmission stream is the audio/video composite
stream, otherwise it only includes video image.
Encode mode
The encode mode of the main stream and extra stream include
G.711A, G.711Mu, G.726 and ACC. The default mode is
G.711A.
The setup here is for audio encode mode and the bidirectional
talk encode both.
Sampling
Frequency
The sampling frequency of audio. It includes the following
options:
8K
16K
32K
48K
64K
54
AudioIn Type
Two modes to select: LineIn, Mic. Device needs to connect
external audio input source under LineIn mode, and it doesn’t
need to connect external audio input source under Mic mode.
Noise Filter
Enable the function and it can filter relevant noise.
Microphone
Volume
Adjust microphone volume from 0~100.
Note:
Supported by some devices.
Speaker Volume
Adjust speaker volume from 0~100.
Note:
Supported by some devices.
5.1.3.2 Alarm audio
Figure 5-27
Figure 5-28
Audio management currently supports PCM format to record and PCM, wav two forms to upload,
and can select an audio file for the audio alarm linkage.
The way to download the web alarm playback audio file into local is as follows:
55
Step 1 Use the left mouse button to click the hollow circle
and shows
in the “choice” column on the left,
,which means effective choice of alarm audio.
Step 2 Use the right mouse button to click
,select “save target as” to download.
5.2 Network
5.2.1 TCP/IP
The TCP/IP interface is shown as in Figure 5-29. It supports IPv4 and IPv6. IPv4 supports static IP and
DHCP. IPv6 supports static IP only. When users manually modify IP address, WEB will automatically
jump to the new IP address.
Figure 5-29
Please refer to the following sheet for detailed information.
Parameter
Function
Host Name
It is to set current host device name. It max supports 15
characters.
Ethernet Card
Please select the Ethernet port. Default is wired.
Please note user may modify the default Ethernet card if there
is more than one card.
Mode
There are two modes: static mode and the DHCP mode. Select
DHCP mode, it auto searches IP, and user maynot set
IP/subnet mask/gateway. Select static mode, you must
manually set IP/subnet mask/gateway.
Mac Address
It is to display hose Mac address.
56
IP Version
It is to select IP version. IPV4 or IPV6.
User may access the IP address of these two versions.
IP Address
Please use the keyboard to input the corresponding number to
modify the IP address and then set the corresponding subnet
mask and the default gateway.
Preferred DNS
DNS IP address.
Alternate DNS
Alternate DNS IP address.
Enable
ARP/Ping set
device IP
address service.
User may use ARP/Ping command to modify or set the device
IP address if you know the device MAC address.
Before the operation, please make sure the network camera
and the PC in the same LAN. This function is on by default.
User may refer to the steps listed below.
Step 1: Get an IP address. Set the network camera and the PC
in the same LAN.
Step 2: Get the physical address from the label of the network
camera.
Step 3: Go to the Run interface and then input the following
commands.
arp –s <IP Address> <MAC>
ping –l 480 –t <IP Address>
Such as:arp -s 192.168.0.125 11-40-8c-18-10-11
ping -l 480 -t 192.168.0.125
Step 4: Reboot the device.
Step 5: User may see the setup is OK if user may see there
are output information such as “Reply from 192.168.0.125 …”
from the command output lines. Now user may close the
command line.
Step 6: Open the browse and then input http://<IP address>.
Click the Enter button, user may access now.
5.2.1.1 Easy4ip
Click “Enable” to connect the device to network, and then user may connect to the device via mobile
client of Easy4ip after “Online” is displayed on the interface (connection mode: add device serial number
or scan QR code). See Figure 5-30.
57
Figure 5-30
5.2.2 Connection
5.2.2.1 Connection
The connection interface is shown as in Figure 5-31.
Figure 5-31
Please refer to the following sheet for detailed information.
58
Parameter
Function
Max
connection
It is the max Web connection for the same device. The value ranges from 1
to 20. Default connection amount is 10.
TCP port
Port range is 1025~65534. The default value is 37777. User may input the
actual port number if necessary.
UDP port
Port range is 1025~65534. The default value is 37778. User may input the
actual port number if necessary.
HTTP port
Port range is 1025~65524. The default value is 80. User may input the
actual port number if necessary.
RTSP port
The default value is 554. Please leave blank if use default. User uses
QuickTime or VLC can play the following formats. BlackBerry can play
too.
Real-time monitoring URL format, please require real-time RTSP
media server, require channel no., bit stream type in URL. You may
need username and password.
User uses BlackBerry need to set encode mode to H.264B, resolution
to CIF and turn off audio.
URL format is:
rtsp://username:password@ip:port/cam/realmonitor?channel=1&subtype=0
Username/password/IP and port.
The IP is device IP and the port default value is 554. User may leave it in
blank if it is the default value.
Follow standard RTP protocol and when encode mode is MJPEG, the max
resolution only supports 2040*2040.
HTTPs
Port
HTTPs communication port, range is 1025~65534, default is 443.
Note:
0~1024, 37780~37880, 1900, 3800, 5000, 5050, 9999, 37776, 39999, 42323 are all special ports.
User cannot modify them.
Avoid using default port value of other ports.
5.2.2.2 ONVIF
ONVIF(Open Network Video Interface Forum),this standard describes network video mode,
interface, data type and data interaction mode. ONVIF Standard’s aim is to achieve a network video
frame agreement and makes the network video products (including video front-end, video equipment,
etc.) from different manufacturers completely compatible.
ONVIF function is on by default.
59
Figure 5-32
5.2.3 PPPoE
The PPPoE interface is shown as in Figure 5-33.
Enter the PPPoE username and password which are provided by ISP (Internet Service Provider), and
click “Enable”. The network camera will automatically establish network connection in the mode of
PPPoE after it is enabled, after it is successful, the IP of the “IP Address” will be automatically modified
into the dynamic IP address of the acquired WAN.
Note:
After PPPoE dial-up is successful, it needs to log in the device via the IP which is set before dial-up; in
the PPPoE setup interface, it will display the registered IP address, and then it can visit the IP address
via client.
Please disable UPnP when clicking PPPoE enable, which is to avoid causing influence to PPPoE dialup.
60
Figure 5-33
5.2.4 DDNS
The DDNS interface is shown as in Figure 5-34.
The DDNS is to set to connect the various servers so that user may access the system via the server.
Please go to the corresponding service website to apply a domain name and then access the system
via the domain. It works even your IP address has changed. When the device connects to WLAN, you
should disable UPnP.
Figure 5-34
Please refer to the following sheet for detailed information.
Parameter
Function
Server Type
Click it to select DDNS protocol type, which includes: CN99
DDNS, NO-IP DDNS, Dyndns DDNS, Quick DDNS, the default is
Quick DDNS.
Server Address
DDNS server IP address
CN99 DDNS
Server address: www.3322.org
NO-IP DDNS
Server address: dynupdate.no-ip.com
Dyndns DDNS
Server address: members.dyndns.org
Quick DDNS
Server address: www.quickddns.com
Mode
Default is auto, it can select manual
61
Parameter
Function
Domain Name
Both auto and manual are “MAC addresss.quickddns.com” by
default, it is able to set prefix manually.
Username
The user name you input to log in the server, optional.
The CN99 DDNS interface is shown as in Figure 5-35.
Figure 5-35
Parameter
Function
Server Type
User may select CN99 DDNS protocol
Server Address
Under CN99 DDNS, the default server address is “www. 3322. org”.
Domain Name
Self-defined domain name
Username
The user name you input to log in the server.
Password
The password you input to log in the server
Refresh Period
The refresh period of the connection between the device IP and the server, default
is 10 minutes.
5.2.5 IP filter
The IP filter interface is shown as in Figure 5-36.
User may enable IP filter function so that some specified IP/MAC user can access the network camera.
User may add IP address or IP segment.
If you do not check the box here, it means there is on access limit.
62
Here user may add IP address and MAC address. You must add these addresses before enabling the
trusted sites.
Please note: You must set MAC address in the same network segment.
Figure 5-36
5.2.6 SMTP (e-mail)
The SMTP interface is shown as in Figure 5-37.
Figure 5-37
Please refer to the following sheet for detailed information.
63
Parameter
Function
SMTP Server
Input server address and then enable this function.
Port
Default value is 25. User may modify it if necessary.
Anonymity
For the server which supports the anonymity email function, it
won’t display the information of the sender.
User Name
The user name of the sender email account.
Password
The password of sender email account.
Sender
Sender email address.
Authentication
(Encryption
mode)
User may select SSL, TLS or none.
Title (Subject)
Input email subject here.
Attachment
System can send out the email of the snapshot picture once
you check the box here.
Mail receiver
Input receiver email address here. Max three addresses.
Interval
The send interval ranges from 0 to 3600 seconds. 0 means
there is no interval.
Please note system will not send out the email immediately
when the alarm occurs. When the alarm, motion detection or
the abnormity event activates the email, system sends out the
email according to the interval you specified here. This
function is very useful when there are too many emails
activated by the abnormity events, which may result in heavy
load for the email server.
Please check the box here to enable this function.
Health mail
enable
Email test
The system will automatically sent out a email once to test the
connection is OK or not .Before the email test, please save
the email setup information.
5.2.7 UPnP
It allows you to establish the mapping relationship between the LAN and the public network.
Here user may also add, modify or remove UPnP item. For UPnP on different routers, you must disable
UPnP function. See Figure 5-38.
In the Windows OS, From Start->Control Panel->Add or remove programs. Click the “Add/Remove
Windows Components” and then select the “Network Services” from the Windows Components Wizard.
Click the Details button and then check the “Internet Gateway Device Discovery and Control client” and
“UPnP User Interface”. Please click OK to begin installation.
64
Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the network camera can auto
detect it via the “My Network Places”.
Under manual mode, user may modify external port. Under auto mode, select idle port for auto port
mapping without user modification.
Figure 5-38
5.2.8 SNMP
The SNMP interface is shown as in Figure 5-39 and Figure 5-40.
The SNMP allows the communication between the network management work station software and the
proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or
establish the SNMP service before you use this function. You need to reboot the device to activate the
new setup.
65
Figure 5-39
Please refer to the following sheet for detailed information.
Parameter
SNMP Version
Function
Check SNMP v1, device only process v1 info.
Check SNMP v2, device only process v2 info.
Check SNMP v3, can set username, password and
encryption method. Server calibrate corresponding
username, password and encryption method too access
device and v1/v2 are unavailable.
SNMP port
The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to 65535.
The default value is 161
Community
It is a string, as command between management and proxy, ,
defining a proxy, and a manager’s authentication.
Read community
Read-only access to all SNMP targets, default is public.
Note: Only number, letter, _, and – supported.
Read/write access to all SNMP targets, default is private.
Note: Only number, letter, _, and – supported.
The destination address of the Trap information from the
proxy program of the device.
Write community
Trap address
Trap
Trap Address
Trap Port
SNMP trap is a proxy message sent to admin as important
event notice or status change.
Address where to send Trap message.
Port which send Trap message, default is 162, range
1~65535.
66
Figure 5-40
Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port
are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, users need to
configure parameter in chart.
Parameter
Function
SNMP Version
SNMP v3
Read-only
Username
Read/Write
Username
Default is public.
Note:
Name only can be number, letter and underline.
Default is private.
Note:
Name only can be number, letter and underline.
Authentication
You may select MD5 or SHA, default is MD5.
Authentication
Password
Password not less than 8 characters.
Encryption
Default is CBC-DES.
Encryption
Password
Password not less than 8 characters.
67
5.2.9 Bonjour
The Bonjour interface is shown as below. See Figure 5-41.
Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically
broadcast its service information and listen to the service information from other device.
User may use the browse of the Bonjour service in the same LAN to search the network camera device
and then access if you do not know the network camera information such as IP address.
User may view the server name when the network camera is detected by the Bonjour. Please note the
safari browse support this function. Click the “Display All Bookmarks: and open the Bonjour, system can
auto detect the network camera of the Bonjour function in the LAN.
Figure 5-41
5.2.10 Multicast
The multicast interface is shown as in Figure 5-42.
Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data
packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host
can just send out one data to transit. This function also depends on the relationship of the group
member and group of the outer.
Note:
Open preview, streaming media protocol, select multicast, and monitor via multicast format.
Here user may set multicast address and port. You also need to go to Live interface to set the
protocol as Multicast.
68
Figure 5-42
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Select to enable multicast function. Main stream and sub stream cannot be
used at the same time.
Multicast address
Main/sub stream multicast default address is 224.1.2.4 and its range is
224.0.0.0~239.255.255.255.
Port
Multicast port. Main stream is 40000, sub stream1 is 40016,sub stream2 is
40032 and the range is 1025~65534.
5.2.11 4G
Note: This function is only for series with 4G module.
4G is a mobile communication system which makes wireless communication integrates with Internet
and multimedia communication.
5.2.11.1 Dialing Setting
69
Figure 4-53
Parameter
Function
Wireless Net Type
Auto, WCDMA, FDD-LTE optional, user may select
according to the operator.
Enable
Check to enable 4G module.
APN
It shall be acquired from the operator according to the setup
of operator.
Authentication Mode
Auto, PAP and CHAP, the authentication algorithm is
different according to different operators.
Dial-up Number
The number is different according to different operator, it can
be acquired from operator.
User name
It shall be acquired from the operator.
Password
It shall be acquired from the operator.
Update Period
It is the period beyond the dial-up period which has been
set, it is 30s by default, which means the device can auto
acquire 4G dial-up status, cut off dial-up to save flow.
Time Range
It is the time period to set dial-up. It can activate the function
via message to enable/disable dial-up function if it is
beyond the time period.
IP Address
It will display the acquired IP after the dial-up is successful
via 4G.
70
5.2.11.2 Mobile Setting
Figure 4-54
Please refer to the following sheet for detailed information.
Parameter
Function
Message Send
In the event, after the corresponding message activation is
enabled, it will send message to the phone of receiver when
event happens. It needs to enable the function of message
activation function in the event interface when using the
function.
Message
Activation
It can send message ON/OFF to the SIM card inside the device by
the mobile phone in the list, which is to enable /disable the dial-up
function and send REBOOT to restart the device.
Phone Activation
User may use the mobile phone in the calling list to call the SIM
card inside the device to enable dial-up function.
5.2.12 WIFI
Note:
Some series devices don’t support WIFI and WPS function.
WPS function is supported by the devices with WPS button.
5.2.12.1 WIFI
WIFI info can show the name, status, IP information of the Current Hot Spot. Usually please “Refresh”
WIFI work information after reconnection to ensure the real-time display of the work status, because it
often takes some time to connect WIFI Hot Spot, which depends on the network signal strength.
71
Figure 5-45
WIFI setting method is as follows:
Step 1
Click
, show as
,means enabling WIFI function.
Step 2
Click “ Search SSID”, and shows the wireless network hot spot of the current network camera
environment in the list.
Figure 5-46
72
Step 3
Click “Add SSID” when need to add a wireless network manually,pop out an interface in the figure
below, and enter network ID in the dialog box.
Figure 5-47
Step 4 Double click on one can pop out the signal intensity and authentication of the hot spot.
· Please enter the password if necessary. Please keep the choice of password index
number same as the router when entering password.
· Please click “connect” if it is unnecessary to enter the password.
5.2.12.2 WPS
Figure 5-48
PIN Number and SSID are both acquired from the router, please “refresh” the work information of WIFI
to ensure the real-time display of work state after filling in correctly.
5.2.13 802.1x
802.1x (port based network access control protocol) supports manual selection of authentication
method to control if device connected to LAN can join the LAN. It well supports authentication, charging,
safety and management requirement of network.
73
Figure 5-49
Please refer to the following sheet for detailed information.
Parameter
Function
Authentication
PEAP (protected EAP protocol).
Username
It needs the username to login, which is authenticated by the
server.
Password
Please input password here.
5.2.14 QoS
The QoS interface is shown as below. See Figure 5-50.
Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and
jam problem and etc. For the network service, the quality of service includes the transmission bandwidth,
delay, the packet loss and etc. We can guarantee the transmission bandwidth, lower the delay, and
reduce the loss of the data packet and anti-dither to enhance the quality.
We can set the DSCP (Differentiated Services Code Point) of the IP to distinguish the data packet so
that the router or the hub can provide different services for various data packets. It can select the
different queues according to the priority (64 different priority levels) of the packets and select the
bandwidth of the each queue. Level 0 is the lowest, and level 63 is the highest. It can also discard at the
different ratio when the broad bandwidth is jam.
74
Figure 5-50
Please refer to the following sheet for detailed information.
Parameter
Function
Real-time
monitor
The value ranges from 0 to 63. The router or the switcher can
provide different service for various data packets.
Command
The value ranges from 0 to 63. The router or the switcher can
provide different service for various data packets.
Enable
Wireless QoS
Check it to enable QoS.
5.2.15 HTTPs
In the HTTPs setting interface, users can make PC log in normally via HTTPs by creating certificate or
uploading signed certificate, which is to guarantee the security of communication data and provide
safeguard for user information and device security with reliable and stable technical means.
Step 1
Create certificate or upload the signed certificate.
Please refer to the following steps if you select “Create Certificate”.
1. Select “Setup > Network > HTTPs”, and the system will display the interface of HTTPs, which is
shown in Figure 5-51.
75
Figure 5-51
2. Click “Create” and it will pop out the dialog box of “HTTPs”, which is shown in Figure 5-52.
Figure 5-52
3. Fill in corresponding “Country”, “Province” and some other information, click “Create” after filling in.
It will show the prompt of “Create Successfully”, which means the server certificate has been
successfully created.
76
Note:
Make sure the “IP or domain name” is the same as that of the device.
4. Click “Install” and it will install the certificate on the device end, which is shown in Figure 5-53.
Figure 5-53
5. Click “Download”. It will pop out the dialog box of “Save as”, save the file into the computer.
77
Figure 5-54
6. Double click the downloaded icon of “RootCert.cer”. The system will display the information
interface of “Certificate”, which is shown in Figure 5-55.
78
Figure 5-55
7. Click “Install Certificate” and it will pop out the interface of “Certificate Import Wizard”, which is
shown in Figure 5-56.
79
Figure 5-56
8. Click “Next”. Select “Trusted Root Certification Authorities”, which is shown in Figure 5-57.
80
Figure 5-57
9. Click “Next”. The system will display the interface of “Completing the Certificate Import Wizard”,
which is shown in Figure 5-58.
81
Figure 5-58
10. Click “Finish”, and it will pop out the dialog box of “Security Warning”, which is shown in Figure 5-59.
82
Figure 5-59
11. Click “Yes”. It will pop out the dialog box of “Import Successful”, click “Ok” to complete downloading
certificate, which is shown in Figure 5-60.
Figure 5-60
Please refer to the following steps if you select “Install Signed Certificate”.
1. Select “Setup > Network > HTTPs”. The system will display the interface of HTTPs, which is shown
in Figure 5-61.
83
Figure 5-61
2. Select signed certificate and certificate key path respectively via “Browse”, click “Upload”.
3. Install root certificate, please refer to step 6~11 for more details.
4. Check “Enable HTTPs”, click “Save”. The system will display the dialog box of “Need to reboot the
device”, and then the config is valid.
Figure 5-62
5. Use HTTPs
Use HTTPs to log in.
Enter https://xx.xx.xx.xx in the browser, and it will pop out normal login interface; the browser will prompt
certificate error if the certificate is not installed, which is shown in Figure 5-63.
84
Figure 5-63
Note:
“xx.xx.xx.xx” is corresponding to your IP or domain name.
5.3 Event
5.3.1 Video detection
5.3.1.1 Motion Detection
Step 1
Select “Setup > Event > Video Detection > Motion Detection’ and the system will display the interface of
“Motion Detection” which is shown in Figure 5-64.
85
Figure 5-64
Step 2
Select “Enable” to enable motion detection function.
Step 3
Set motion detection area.
1. Click “Setup” and the system will pop out the interface of “Setting Area”, which is shown in Figure 565
86
Figure 5-65
2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can
set the value of sensitivity and threshold respectively.
The bigger the sensitivity is, the easier it is to generate motion detection, the smaller the threshold is,
the easier it is to generate motion detection; the entire video image is the valid area of motion
detection by default.
Note:
Different colors represent different areas; each area can set different detection area.
The red line in the Oscillogram means triggering motion detection; green line means not triggering
motion detection.
3. Click “Save” to complete area setting.
Step 4
It is to set other parameters of motion detection, please refer to the following sheet for more details.
87
Parameter
Function
Working Period
Note:
It is to set the alarm period, it can enable alarm event only during the
period range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the
whole week, then it means the setup can be applied to the whole
week, user may also select the check box in front of the week number
to implement independent setting for some days).
3. Click “Save” to complete the setup of working period.
System only memorizes one event during the anti-dither period. The value
ranges from 0s to 100s.
1. Click “Setup” and the system will pop out the interface of “Set Area”.
2. Set the area name, it is to set the valid area of motion detection
according to the actual situation, and it can set its sensitivity and
threshold respectively. The higher the sensitivity is, the easier it is to
trigger motion detect, the smaller the area threshold is, the easier it is
to generate motion detect, the whole video image is the valid area of
the motion detect by default.
Note:
Different colors represent different areas; each area can set different
detection areas.
The red line in the Oscillogram means triggering motion detect, the green
line means not triggering motion detect.
3. Click “Save” to complete area setup.
Check it and so when alarm occurs, system will auto record. You shall set
record period in Storage>Schedule and select auto record in record control
interface.
Anti-dither
Area
Record
Record Delay
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended. The
value ranges from 10s to 300s.
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Check it and the system will play alarm audio file when alarm occurs. Users
can set the recorded or uploaded audio file in “camera setting > audio >
alarm audio”.
Send Email
Audio linkage
88
Parameter
Function
Flash linkage
Check it and the flash will be on when alarm occurs, and the flash will
be off until the end of alarm after corresponding delay.
Here user may set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
The event type includes: preset, tour and pattern.
You need to check the box here so that system can backup motion detection
snapshot file. You shall set snapshot period in Storage>Schedule.
PTZ
Snapshot
Step 5
Click “Save” to complete the setting of motion detection.
5.3.1.2 Video Tampering
Step 1
Select “Setup > Event > Video Detection > Video Tampering” and the system will display the interface of
“Video Tampering” which is shown in Figure 5-66.
Figure 5-66
Step 2
Set the parameter of video tampering; please refer to the following sheet for more details.
Parameter
Function
Enable video
tampering
You need to check the box to enable video mask detection alarm.
Enable defocus
detection
You need to check the box to enable defocus detection alarm.
89
Parameter
Function
Working Period
Note:
It is to set the alarm period, it can enable alarm event only during the
period range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the
whole week, then it means the setup can be applied to the whole
week, user may also select the check box in front of the week number
to implement independent setting for some days).
3. Click “Save” to complete the setup of working period.
Check it and so when alarm occurs, system will auto record. You shall set
record period in Storage>Schedule and select auto record in record control
interface.
Record
Record Delay
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended. The
value ranges from 10s to 300s.
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Check it and the system will play alarm audio file when alarm occurs. Users
can set the recorded or uploaded audio file in “camera setting > audio >
alarm audio”.
Check it and the flash will be on when alarm occurs, and the flash will
be off until the end of alarm after corresponding delay.
Here user may set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
The event type includes: preset, tour and pattern.
You need to check the box here so that system can backup motion detection
snapshot file. You shall set snapshot period in Storage>Schedule.
Send Email
Audio linkage
Flash linkage
PTZ
Snapshot
Step 3
Click “Save” to complete the setup of video tampering.
5.3.1.3 Scene Changing
Step 1
Select “Setup > Event > Video Detection > Scene Changing” and the system will display the interface of
“Scene Changing” which is shown in Figure 5-67.
90
Figure 5-67
Step 2
Check “Enable” to enable the function of scene changing.
Step 3
It is to set the parameters of scene changing, please refer to the following sheet for more details.
Parameter
Function
Working Period
Note:
It is to set the alarm period, it can enable alarm event only during the
period range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the
whole week, then it means the setup can be applied to the whole
week, user may also select the check box in front of the week number
to implement independent setting for some days).
3. Click “Save” to complete the setup of working period.
Check it and so when alarm occurs, system will auto record. You shall set
record period in Storage>Schedule and select auto record in record control
interface.
Record
Record Delay
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended. The
value ranges from 10s to 300s.
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Send Email
91
Parameter
Function
PTZ
Here user may set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
The event type includes: preset, tour and pattern.
You need to check the box here so that system can backup motion detection
snapshot file. You shall set snapshot period in Storage>Schedule.
Snapshot
Step 4
Click “Save” to complete the setup of scene changing.
5.3.2 Audio Detection
Step 1
Select “Setup > Event > Audio Detection” and the system will display the interface of “Audio Detection”
which is shown in Figure 5-68.
Figure 5-68
Step 2
It is to set the parameters of audio detect, please refer to the following sheet for more details.
Parameter
Function
Enable input
abnormal
Select “Enable Input Abnormal” and it will trigger alarm when it detects
audio input abnormity.
Enable intensity
change
Select “Enable Intensity Change” and it will trigger alarm when it detects
that audio intensity change exceeds the threshold.
92
Parameter
Function
Sensitivity
It can be judged as audio abnormity when the input volume change
exceeds continuous environment volume; users need to adjust according
to the actual environment test.
Threshold
It is to set the filtered environment volume intensity, if the environmental
noise is too big, then the value needs to be set higher, users can adjust
according to the actual environment test.
Working Period
Note:
It is to set the alarm period, it can enable alarm event only during the
period range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the
whole week, then it means the setup can be applied to the whole
week, user may also select the check box in front of the week number
to implement independent setting for some days).
3. Click “Save” to complete the setup of working period.
System only memorizes one event during the anti-dither period. The value
ranges from 0s to 100s.
Check it and so when alarm occurs, system will auto record. You shall set
record period in Storage>Schedule and select auto record in record control
interface.
Anti-dither
Record
Record Delay
System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended. The
value ranges from 10s to 300s.
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Here user may set PTZ movement when alarm occurs. Such as go to
preset x when there is an alarm.
The event type includes: preset, tour and pattern.
You need to check the box here so that system can backup motion detection
snapshot file. You shall set snapshot period in Storage>Schedule.
Send Email
PTZ
Snapshot
Step 3
Click “Save” to complete the setup of audio detection.
93
5.3.3 Smart Plan
Smart plan is the master switch for intelligent analysis such as “Face Detection”, “Heat Map”, “IVS”,
“People Counting” and so on, the corresponding intelligent functions can be valid after smart plan is
enabled.
Step 1
Select “Setup > Event > Smart Plan”. The system will display the interface of “Smart Plan”, which is
shown in Figure 5-69.
Figure 5-69
Step 2
Click “Save” to complete the config of smart plan.
5.3.4 Intelligence Behavior Analytics
The basic requirements of scene selection
The total proportion of the target shall not exceed 10% of the image.
The target size in the image can’t be less than 10 pixel ×10 pixel, the size of abandoned target can’t
be less than 15 pixel × 15 pixel (CIF image); The height and width of the target can’t exceed 1/3 of
the image; it is recommended that the target height is about 10% of the image height.
The difference of brightness value between target and background can’t be less than 10 gray levels.
Make sure the target appears at least over 2 seconds continuously in the field; the movement
distance has to be bigger than the width of the target itself and makes sure it is no less than 15
pixels (CIF image).
Try to lower the complexity of the monitoring scene analysis if it is possible; it is not advised to use
IVS functions in the environment where the targets are dense and light change is very frequent.
Try to keep away from the areas such as glass, ground reflected light, water surface, branch,
shadow, mosquito disturbance and etc.; try to keep away from the backlight scene to avoid direct
light.
94
5.3.4.1 IVS
5.3.4.1.1
Tripwire
It will trigger alarm when the target crosses the warning line according to the movement direction which
has been set.
It needs some time from when the target appears to when the target is confirmed, so it has to leave
some space on both sides of the warning line when setting the warning line, please do not set the
warning line near the obstructions.
Application scene: it can be applied to the scene with sparse target and there is barely any blocks
between the targets, such as the unmanned perimeter defense.
Step 1
Select “Setup > Event > IVS > IVS” and the system will display the interface of “IVS”.
Step 2
Click “
” to set rule name and select the rule type as “Tripwire” which is shown in Figure 5-70.
Figure 5-70
Step 3
Click “Draw Rule” to draw tripwire in the monitoring scene, click the right mouse button to complete
tripwire setting.
Step 4
Click “Draw Target” to draw the size model of filtered target in the video image.
Step 5
It is to set the parameters of tripwire, please refer to the following sheet for more details.
95
Parameter
Function
Object tracking
Select “Object tracking” to enable the function, refer to “2.4 Video Window
Adjustment” for more details.
Note:
The function is only supported by some models.
Working Period
Direction
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
It is to set the direction of tripwire, user may select A->B、B->A、A<->B.
Record
Select “Object Track” and it will enable the function of object track; when the
moving object triggers rule and generates alarm, it will select the display
mode of object track such as 1P+3 or 1P+5 in the preview interface, the
scene of tracking window will follow the moving object till the object leaves
the view range of the camera. Please refer to “2.4.8 Fisheye/Trigger Track”
for more details.
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Object Track
Snapshot
Step 5
Click “Save” to complete the setup of tripwire.
5.3.4.2 Intrusion
Intrusion includes cross and appears.
96
Cross means that it will trigger alarm when the target enters or exits the area.
Appears means that it will trigger alarm when the target appears in the area.
As for the report interval of the IVS function in the area, the system will trigger an alarm if it detects
same event happened during the interval; the alarm counter will become zero if there is no same
event happened in the interval.
It needs to leave some space for target movement for the area periphery if it is to detect enter & exit
event, which is similar to the warning line.
Application scene; it can be applied to the scene where the target is sparse and there is barely any
obstruction between the targets, such as the unmanned perimeter defense.
Step 1
Select “Setup > Event > IVS > IVS” and the system will display the interface of “IVS”.
Step 2
Click “
” to set rule name, select the rule type as “Intrusion” which is shown in Figure 5-71.
Figure 5-71
Step 3
Click “Draw Rule” to draw an area in the monitoring image.
Step 4
Click “Draw Target” to draw the size model of filtered target in the video image.
Step 5
It is to set the parameters of intrusion, please refer the following sheet for more details.
97
Parameter
Function
Object tracking
Select “Object tracking” to enable the function, refer to “2.4 Video Window
Adjustment” for more details.
Note:
The function is only supported by some models.
Working Period
Action
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
It is to set the action of intrusion, user may select appears and cross.
Record
It is to set the direction of intrusion, user may select enter, exit and
enter&exit.
Select “Object Track” and it will enable the function of object track; when the
moving object triggers rule and generates alarm, it will select the display
mode of object track such as 1P+3 or 1P+5 in the preview interface, the
scene of tracking window will follow the moving object till the object leaves
the view range of the camera. Please refer to “2.4.8 Fisheye/Trigger Track”
for more details.
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Direction
Object Track
Snapshot
Step 5
Click “Save” to complete the setup of intrusion.
98
5.3.4.3 Abandoned Object
Abandoned object means the system will trigger alarm if the abandoned object in the monitoring scene
exceeds the time which has been set by the users.
Abandoned object and missing object can be confusing in a situation where both foreground and
background are complicated.
It also triggers alarm as abandoned object if there is pedestrian or vehicle staying still for too long. In
order to filter this kind of alarm, generally the abandoned object is smaller than people and vehicle;
therefore it can filter the people and vehicle via setting size. Besides, it can avoid the false alarm caused
by short stay of people via extending alarm time properly.
Application scene: It can be applied to the scene where the target is sparse and there is no obvious and
frequent light change. False alarm will be increased in the scene with high target density and frequent
blocking; false alarm will be increased in the scene where there are more people staying. As for the
detection area, try to make it simple, the function is not suitable for the area which is too complicated.
Step 1
Select “Setup > Event > IVS > IVS” and the system will display the interface of “IVS”.
Step 2
Click “
” to set rule name, select the rule type as “Abandoned Object” which is shown in Figure 5-72.
Figure 5-72
Step 3
Click “Draw Rule” to draw an area in the monitoring area.
Step 4
Click “Draw Target” to draw the size model of filtered target in the video image.
Step 5
99
It is to set the parameter of abandoned object, please refer to the following sheet for more details.
Parameter
Function
Working Period
Record
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
It is to set the shortest time from when the object is abandoned to when it
triggers alarm.
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Keep time
Snapshot
Step 5
Click “Save” to complete the setup of abandoned object.
5.3.4.4 Missing Object
Missing object means the system will trigger alarm if it exceeds certain amount of time after the target is
taken away from the original scene.
The system can make statistics of the still areas in the foreground area and distinguish if it is missing
object or abandoned object according to the similarity between foreground and background, it will
trigger alarm when it exceeds the time which is set by users.
Because the system distinguishes abandoned object from missing object according to the similarity of
foreground and background, it may cause error between abandoned object and missing object in a
situation where both foreground and background are complicated.
100
Application scene: it can be applied to the scene where the target is sparse and there is no obvious and
frequent light change. False alarm will be increased in the scene where the target density is high and
there is frequent obstruction; the false alarm will be increased in the scene where there are more people
staying. As for the detection area, try to make it simple, the function is not suitable for the area which is
too complicated.
Step 1
Select “Setup > Event > IVS > IVS” and the system will display the interface of “IVS”.
Step 2
Click “
” to set rule name and select rule type as “Missing Object”, which is shown in Figure 5-73.
Figure 5-73
Step 3
Click “Draw Rule” to draw an area in the monitoring scene.
Step 4
Click “Draw Target” to draw the size model of filtered target in the video image.
Step 5
It is to set the parameters of missing object, please refer to the following sheet for more details.
101
Parameter
Function
Working Period
Record
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
It is to set the shortest time from when the object is missing to when it
triggers alarm.
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Keep time
Snapshot
Step 5
Click “Save” to complete the setup of missing object.
5.3.5 Face Detection
Step 1
Select “Setup > Event > Face Detection” and the system will display the interface of “Face Detection”,
which is shown in Figure 5-74.
102
Figure 5-74
Step 2
Select “Enable” to enable face detection function.
Step 3
Click “Draw Target” to draw the size model of target filter in the video image.
Step 4
It is to set the parameters of face detection, please refer to the following sheet for more details.
Parameter
Function
Working Period
Enable Face
Enhancement
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
Select “Enable Face Enhancement” and it will guarantee that the face is
clear by priority when the stream is set very low.
Record
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
103
Parameter
Function
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Snapshot
Step 5
Click “Save” to complete the setup of face detection.
5.3.6 People Counting
5.3.6.1 People Counting
Step 1
Select “Setup > Event > People Counting > People Counting” and the system will display the interface
of “Entrance/Exit”, which is shown in Figure 5-75.
Figure 5-75
Step 2
Select “Enable” to enable statistics function of entrance and exit.
Step 3
Click “Draw Rule” to draw an area in the monitoring image.
Step 4
104
Click “Draw Target” to draw the size model of filtered target in the video image.
Step 5
It is to set the parameters of entrance and exit, please refer to the following sheet for more details.
Parameter
Function
Enable OSD
Installation
Mode
Select “Enable OSD” and it will display the people number statistics of
entrance and exit in the monitoring image.
Note:
It is to set the alarm period, it can enable alarm event only during the period
range which has been set.
1. Click “Setup” and the system will pop out the interface of “Working
Period”.
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to
drag on the setup interface to set.
There are six periods to be set every day, select the check box in front
of the period, and then the period is valid.
Select week number (it selects Sunday by default, if it selects the whole
week, then it means the setup can be applied to the whole week, user
may also select the check box in front of the week number to implement
independent setting for some days).
3. Click “Save” to complete the setup of working period.
It is to select wall mount if there is an angle between device lens and
horizontal surface, select ceiling if the device lens face downward vertically.
Rule Name
It is to set the name of rule.
Direction
Record
It is to select the direction of entrance and exit statistics; A->B or B->A, the
arrow direction always means the entrance direction.
It is to set the enter number, leave number, stranded number; it will trigger
alarm when it exceeds the limited number.
Check it and so when alarm occurs, system will auto record.
Record Delay
System can delay the record for specified time after alarm ended.
Relay out
Enable alarm activation function. You need to select alarm output port so
that system can activate corresponding alarm device when alarm occurs.
Alarm Delay
System can delay the alarm output for specified time after alarm ended.
Send Email
If you enabled this function, System can send out email to alert you when
alarm occurs and ends. User can set email address in Network>SMTP.
Select “Snapshot” and the system will auto trigger alarm and snapshot when
alarm occurs.
Working Period
Flowrate Alarm
Snapshot
Step 6
Click “Save” to complete the setup of people counting.
5.3.6.2 Report
105
It is to generate a form of report according to the number statistics.
Step 1
Select “Setup > Event > People Counting > Report “and the system will display the interface of “Report’,
which is shown in Figure 5-76.
Figure 5-76
Step 2
It is to set search condition, please refer to the following sheet for more details.
Parameter
Note
Report Type
Can select day report, month report and year report; also can select bar chart or line
chart to display the report.
Time
It can set the begin /end time within the range of statistics time.
Flow Direction
It can select enter, leave and display number; the data of checked item can be
displayed in the report.
Search
Search flow statistics data according to the setting to form report.
Export
Export the saved report.
Step 3
Click “Search” to complete report statistics, click “Export” to export the report.
5.3.7 Heat Map
5.3.7.1 Heat Map
It is the density statistics of moving object that can generate report, the color range is from blue to red,
blue means the min heat value and red means the max heat value.
Mirroring, view angle change and heat map original data will be cleared.
Step 1
106
Select “Setup > Event > Heat Map > Heat Map” and the system will display the interface of “Heat Map”,
which is shown in Figure 5-77.
Figure 5-77
Step 2
Select “Enable” to enable heat map function.
Step 3
It is to set the working period.
1. Click “Setup” and the system will display the interface of “Working Period”, which is shown in Figure
5-78.
107
Figure 5-78
2. It is to set working period according to the following methods:
User may input time numerical value or press the left mouse button to drag on the setup interface
to set.
There are six periods to be set every day, select the check box in front of the period, and then the
period is valid.
Select week number (it selects Sunday by default, if it selects the whole week, then it means the
setup can be applied to the whole week, user may also select the check box in front of the week
number to implement independent setting for some days).
3. Click “Save” to complete the setup of working period.
Step 4
Click “Save” to complete the setup of heat map.
5.3.7.2 Report
It is to generate the form of report according to the heat map data.
Step 1
Select “Setup > Event > Heat Map > Report” and the system will display the interface of “Report”, which
is shown in Figure 5-79.
108
Figure 5-79
Step 2
It is to set begin time and end time.
Step 3
Click “Search” to complete report statistics, click “Export” to export the statistics report.
5.3.8 Alarm
Please note some series products do not support this function.
5.3.2.1 PIR alarm
The alarm activation interface PIR alarm is shown as in figure 5-80.
109
Figure 5-80
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
After enabled, relay activation will work. Check it and enable the
PIR alarm.
Working
period
This function becomes activated in the specified periods.
There are six periods in one day. Please draw a circle to
enable corresponding period.
Select date. If you do not select, current setup applies to
today only. User may select all week column to apply to the
whole week.
Click OK button, system goes back to motion detection
interface; please click save button to exit.
Note: User can set via dragging mouse while not releasing left
mouse.
System only memorizes one event during the anti-dither period.
The value ranges from 0s to 100s.
After enabling, the system will automatically turn on the flash
when alarm occurs.
Anti-dither
Flash
Flash Delay
The flash will be off with a period of time delay when the
alarm linkage is over.
Time is calculated by unit of second and ranges from
10s~300s.
Record
System auto activates motion detection channel to record once
alarm occurs (working with motion detection function).
Record Delay
System can delay the record for specified time after alarm ended.
The value ranges from 10s to 300s.
110
Parameter
Function
Relay out
Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
alarm occurs.
System can delay the alarm output for specified time after alarm
ended. The value ranges from 10s to 300s.
Alarm delay
Send Email
After this function is enabled, system can send out email to alert
you when alarm occurs and ends.
Audio Linkage
Check it and the system will play alarm audio file when alarm
occurs. Users can set recorded audio file in “Camera Setting >
Audio >Alarm Audio”.
Snapshot
After you enabled snapshot, the system will automatically
snapshot if alarm occurs.
5.3.8.1 Alarm Linkage
Figure 5-81
Parameter
Function
Enable
Check it and enable the alarm linkage.
Relay-in
The default alarm 1,some products can choose alarm 2.
Sensor Type
Two types of sensor which are normally open (NO) and normally closed (NC),
switch from normally open to normally closed, open the alarm. Switch from normally
closed to normally open, shut the alarm.
111
Parameter
Function
PTZ
Check it and set PTZ movement when alarm occurs. Such as go to preset x when
there is an alarm.
The event type includes: preset, tour and pattern and so on.
5.3.8.2 Flash Set
Figure 5-82
Parameter
Function
ON/OFF
ON means flash is on; OFF means flash is off.
Weak-strong
bar
Via dragging this bar to adjust flash brightness.
All
Check and it means the day flash works.
Period
Period that flash is on.
5.3.8.3 Audio detection
Note: Audio detection won’t work when “Talk” is enabled on the preview interface.
112
Figure 5-83
parameter
Function
Enable
Check it and enable audio detection.
Threshold
It will trigger alarm and set up a series of linkage when volume exceeds the set
threshold.
5.3.9 Abnormity
Abnormity includes No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict and
Unauthorized Access.
Note:
Only device with SD card function has these three statuses: No SD card, capacity warning, and SD card
error. Device without SD card function does not have the above three statuses. See Figure 5-84 to
Figure 5-86.
113
Figure 5-84
Figure 5-85
114
Figure 5-86
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Check to alarm when SD card is abnormal.
Relay-out
Check to enable relay-out alarm.
Relay out
delay
The alarm output can delay for the specified time after alarm stops. The
value ranges from 10s to 300s.
Note:
No SD card, capacity warning, SD card error, relay-out delay all start
from alarm occurs.
Send
email
After you enabled this function, the system can send out email to alarm
the specified user.
This function is invalid when network is offline or IP conflict occurs.
SD Card
Capacity
Limit
User can set SD card capacity that is left free. When SD card space left
is smaller than this limit, alarm occurs.
When device is offline or IP conflicts, the abnormal alarm is similar with case of SD card error.
115
Figure 5-87
When login password keep been wrong for a few times, unauthorized access alarm occurs. This
operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account
will be locked.
Figure 5-88
5.4 Storage Management
5.4.1 Schedule
Before schedule setup, user must set record mode is auto or manual.
Note:
If record mode in record control is off, then device will not snapshot according to schedule.
5.4.1.1 Record Schedule
Record schedule steps:
Step 1. Click on Record Schedule, see Figure 5-89.
116
Figure 5-89
Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 5-90.
Set period according to actual need. There are six periods available each day.
By checking or unchecking, user may add or delete three types of record schedule: General,
Motion, and Alarm.
Note:
Period setup can be done by dragging in record schedule interface while not releasing left mouse.
Figure 5-90
Step 3. Click on OK, return to record schedule interface. See Figure 5-91.
Green color stands for the general record/snapshot.
Yellow color stands for the motion detect record/snapshot.
Red color stands for the alarm record/snapshot.
117
Figure 5-91
Step 4. In record schedule interface, click on OK. System prompts it is successfully saved.
5.4.1.2 Snapshot Schedule
Snapshot setup as:
Step 1. Click on Snapshot Schedule tab, see Figure 5-92.
Figure 5-92
Step 2. From Monday to Sunday select snapshot time, click on setup on the right. See Figure 5-93.
Set snapshot period according to actual need. There are six periods available each day.
118
By checking or unchecking, user can add or delete three types of snapshot schedule: General,
Motion and Alarm.
Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left
mouse.
Figure 5-93
Step 3. Click on OK, return to snapshot schedule interface. See Figure 5-94.
Green color stands for the general record/snapshot.
Yellow color stands for the motion detect record/snapshot.
Red color stands for the alarm record/snapshot.
Figure 5-94
Step 5. In snapshot interface, click on OK. System prompts it is successfully saved.
119
5.4.1.3 Holiday Schedule
Holiday schedule can set specific date as holiday.
Step 1. Click on Holiday Schedule tab, see Figure 5-95.
Figure 5-95
Step 2. Select date to set as holiday. The selected date will be highlighted in yellow.
Step 3. Check Record/Snapshot, click on Save. System prompts it is successfully saved.
Step 4. Check Record Schedule/Snapshot Schedule interface, click on setup next to Holiday, and refer
to setup of Monday to Sunday.
Step 5. Complete setup of holiday, then it records/snapshots according to date in holiday schedule.
5.4.2 Destination
5.4.2.1 Path
The destination interface is shown as in Figure 5-96.
Path can config record and snapshot storage path. There are three options: Local, FTP and NAS. User
may only select one mode. System can save according to the event types. It is corresponding to the
three modes (general/motion/alarm) in the Schedule interface. Please check the box to enable the save
functions.
Note: Only device supports SD card has local.
120
Figure 5-96
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
It includes: scheduled, motion detect and alarm.
Local
It saved in the SD card.
FTP
It saved in the FTP server.
NAS
It saved in NAS disk.
5.4.2.2 Local
The local interface is shown as in Figure 5-97.
Here user may view local Micro SD card or NAS disk information. User may also operate the read-only,
write-only, hot swap and format operation.
Figure 5-97
5.4.2.3 FTP
The FTP interface is shown as in Figure 5-96.
121
You need to check the box to enable the FTP function. When network disconnect occurred or there is
malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Click the
test button to check if the FTP server can be connected for test.
Figure 5-98
5.4.2.4 NAS
You need to check the box to enable the NAS function. Select NAS storage, fill in NAS server address
and corresponding store path, then user may store video file or pictorial information in the NAS server.
See Figure 5-99.
Figure 5-99
Parameter
Function
Server Address
Set IP address of NAS server.
Remote
Directory
Set storage directory, videos and pictures can be stored in to corresponding server
directory.
5.4.3 Record control
122
The record control interface is shown as in Figure 5-100.
Figure 5-100
Please refer to the following sheet for detailed information.
Parameter
Function
Pack
Duration
Here user may select file size within 1min~120min. Default setup is
8 minutes.
Pre-record
Please input pre-record value here.
For example, system can record the four seconds video in the buffer.
The record begins from the fifth second.
Note:
Configure pre-record time, when alarm or motion detection occurs, if
there is no record, system will record the preceding n seconds
record.
Disk Full
Record
mode
Record
stream
There are two options: stop recording or overwrite the previous files
when HDD is full.
Stop: Current working HDD is overwriting or current HDD is full,
it will stop record.
Overwrite: Current working HDD is full; it will overwrite the
previous file.
There are three modes: Auto/manual/close.
There are two options: main stream and sub stream.
5.5 System
5.5.1 General
The General interface is shown as in Figure 5-101.
123
Figure 5-101
Please refer to the following sheet for detailed information.
Parameter
Function
Device
Name
It is to set device name.
Note: Different devices have different names.
Video
Standard
This is to display video standard such as PAL.
Language
User may select the language from the dropdown list.
TV Out
User may open or close the function, it can only be supported by the
devices with TV Out.
Intelligent function will be disabled when TV Out is opened.
It will auto close TV Out when intelligent function is enabled.
Some devices support SDI and HDCVI.
The date and time interface is shown as in Figure 5-102.
124
Figure 5-102
Please refer to the following sheet for detailed information.
Parameter
Function
Date format
Here user may select date format from the dropdown list.
Time
Format
There are two options: 24-H and 12-H.
Time zone
The time zone of the device.
Current
Time
It is to set system time. It becomes valid after you set.
Sync PC
User may click this button to save the system time as your PC
current time.
DST Enable
Here user may set both begin and end time of daylight saving time.
User may set according to the date format or the week format.
Synchronize
with NTP
User may check the box to enable NTP function.
NTP server
User may set the time server address.
Port
It is to set the time server port.
Update
period
It is to set the sync periods between the device and the time server.
125
5.5.2 Account
For user name and user group, the max length is 31 characters, which can be made up of digit,
letter, underline, hyphen, dot and @.
Password can be 0~32 characters in number and letter only. User can modify other user’s
password.
User and group can be manually added to 18 and 8 respectively.
User management adopts group/user modes. The user name and the group name shall be unique.
One user shall be included in only one group.
Currently logged in user cannot change his/her own right.
5.5.2.1 Username
In this interface user may enable anonymity login, add/remove user and modify user name. See Figure
5-103.
Figure 5-103
Enable anonymity login: Enable anonymity login, and input IP. No username or password is required,
user may log in by anonymity (with limited rights). User may click logout to end your session.
Add user: It is to add a name to group and set the user rights. See Figure 5-104.
Hidden user “default” is for system interior use only and cannot be deleted. When there is no login user,
hidden user “default” automatically login. User may set some rights such as monitor for this user so that
user may view some channel view without login.
Here user may input the user name and password and then select one group for current user.
Please note the user rights shall not exceed the group right setup.
For convenient setup, please make sure the general user has the lower rights setup than the admin.
126
Figure 5-104
Modify user
It is to modify the user property, belonging group, password and rights. See Figure 5-105.
Modify password
It is to modify the user password. You need to input the old password and then input the new password
twice to confirm the new setup. Please click the OK button to save.
Please note, the password ranges from 0-digit to 32-digit. It shall include the number and letter only. For
the user who has the account rights, he can modify the password of other users.
127
Figure 5-105
5.5.2.2 Group
The group management interface can add/remove group, modify group password and etc.
The interface is shown as in Figure 5-106.
Figure 5-106
Add group: It is to add group and set its corresponding rights. See Figure 5-107.
128
Please input the group name and then check the box to select the corresponding rights. It includes:
preview, playback, record control, PTZ control and etc.
Figure 5-107
Modify group
Click the modify group button, user may see an interface is shown as in Figure 5-108.
Here user may modify group information such as remarks and rights.
Figure 5-108
5.5.3 PTZ
Please note only some series products support this function.
129
The PTZ settings interface is shown as in Figure 5-91.
Figure 5-109
Please refer to the following sheet for detailed information.
Parameter
Function
Protocol
Select the corresponding dome protocol.
Address
Set corresponding dome address. Default value is 1.
Please note your setup here shall comply with your dome address;
otherwise user maynot control the speed dome.
Select the dome baud rate. Default setup is 9600.
Baud
Rate
Data Bit
Default setup is 8.
Stop bit
Default setup is 1.
Parity
Default setup is none.
5.5.4 Default
The default setup interface is shown as in Figure 5-110.
Please note system cannot restore some information such as network IP address, account and so on.
130
Figure 5-110
5.5.5 Import/Export
The interface is shown as in Figure 5-111.
Figure 5-111
Please refer to the following sheet for detailed information.
Parameter
Function
Import
It is to import the local setup files to the system.
Export
It is to export the corresponding system setup to your local PC.
5.5.6 Remote control
Note:
It is supported by some devices.
131
Figure 5-112
Parameter
Function
Learn
Bind remote control or wireless alarm with equipment.
Clear
Unbind remote control with equipment.
Start arm after the time you choose, disarm comes into effect immediately. Note:
Arm/Disarm
With disarm status, all the following alarms won’t trigger: motion detect alarm,
masking alarm, local alarm, PIR alarm, wireless alarm.
5.5.6 Auto Maintenance
The auto maintenance interface is shown as in Figure 5-113.
Here user may select auto reboot and auto delete old files interval from the dropdown list.
If you want to use the auto delete old files function, you need to set the file period.
Figure 5-113
132
Parameter
Function
Auto Reboot
Check it and set auto reboot time.
Auto Delete Old
Files
Check it and set period within 1~31 days.
5.5.7 Upgrade
The upgrade interface is shown as in Figure 5-114.
Please select the upgrade file (file extension is “.bin”) and then click the update button to begin firmware
update.
Important
Improper upgrade program may result in device malfunction!
Figure 5-114
5.6 Information
5.6.1 Version
The version interface is shown as in Figure 5-115.
Here user may view system hardware features, software version, release date and etc. Please note the
following information is for reference only.
Figure 5-115
133
5.6.2 Log
Here user may view system log. See Figure 5-116.
Figure 5-116
Please refer to the following sheet for log parameter information.
Parameter
Function
Start time
Set the start time of the requested log. (The earliest time is 2000/1/1)
End time
Set the end time of the requested log. (The latest time is 2037/12/31)
Type
Search
Log
information
Log type.
User may select log type from the drop down list and then click
search button to view the list.
User may click the stop button to terminate current search operation.
User may select one item to view the detailed information.
Clear
User may click this button to delete all displayed log files. Please
note system does not support clear by type.
Backup
User may click this button to backup log files to current PC.
5.6.3 Online User
The online user interface is shown as in Figure 5-117.
Here user may view current online user, group name, IP address and login time.
134
Figure 5-117
135
6 Alarm
Please note some series product does not support this function.
Click alarm function, user may see an interface is shown as in Figure 6-1.
Here user may set device alarm type and alarm sound setup.
Figure 6-1
Please refer to the following sheet for detailed information.
Type
Parameter
Function
Alarm
Motion detection System alarms when motion detection alarm
type
occurs,
Disk full
System alarms when disk is full.
Disk Error
Video
Tampering
External alarm
Illegal Access
Audio Detection
IVS
Scene Changing
System records alarm info when disk error
happens.
System alarms when video is tampering.
Alarm input device sends out alarm.
System alarms when there is illegal access.
System alarms when there is audio detect.
System alarms when IVS event is triggered.
System will record alarm info when triggering
scene changing.
136
Type
Operation
Parameter
Prompt
Alarm
Tone
Play Alarm Tone
Tone Path
Function
When alarm is triggered, there will be s
inmain menu of alarm interface and system
automatically records alarm info. The icon
disappears when user click on alarm menu bar.
Note:
If alarm interface is displayed, when alarm is
triggered, there will be no image prompt, but alarm
record will be in list on the right.
Click it and select the path of audio file to be
played in the tone path, when the subscribed alarm
event triggers, it will play the selected audio file to
prompt that there is alarm event which has been
triggered.
User may customize the storage path of the alarm
tone.
137
7 Log out
Click log out button, system goes back to log in interface. See Figure 7-1.
Figure 7-1
Note:
This manual is for reference only. Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website for more information.
www.dantesecurity.net
sales@dantesecurity.net
support@dantesecurity.net
138
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising