UREA/DEF AC Transfer Pump Kit USER'S MANUAL

UREA/DEF AC Transfer Pump Kit USER'S MANUAL
UREA/DEF AC Transfer Pump Ki
USER’S MANUAL
UREA/DEF AC Transfer Pump Kit
USER’S MANUAL
MODEL NUMBER
10302500 & 10302501 & 10302502 &
10302503 & 10302504 &10302505
A. MACHINE DESCRIPTION
PUMP: Self-priming, volumetric, diaphragm pump, equipped with by-pass valve.
MOTOR: Asynchronous motor, single-phase, 2 pole, closed type (protection class IP55 in conformance with EN 60034-5-86 regulations)
self-ventilated.
B. TECHNICAL DATA
B1. Configuration
Item No.
Pump Model
Voltage
Suction Hose
Delivery Hose
Nozzle
Flow Meter
10302500
17350250
230V
1.5M
6M
Manual
N/A
10302501
17350251
120V
1.5M
6M
Manual
N/A
10302502
17350250
230V
1.5M
6M
Manual
Yes
10302503
17350251
120V
1.5M
6M
Manual
Yes
10302504
17350250
230V
1.5M
6M
Auto
Yes
10302505
17350251
120V
1.5M
6M
Auto
Yes
C. OPERATING CONDITIONS
C1. ENVIRONMENTAL CONDITIONS
TEMPERATURE: Min. -10˚C(14˚F) / Max. +60˚C(140˚F)
RELATIVE HUMIDITY: Max. 90%
ATTENTION!
The temperature limits shown apply to the pump components and must be respected to avoid possible damage or malfunction.
C2. ELECTRICAL POWER SUPPLY
Depending on the model, the pump must be supplied by a single-phase alternating current line whose nominal values are shown in the
table in Paragraph B1 – ELECTRICAL SPECIFICATIONS.
The maximum acceptable variations from the electrical parameters are:
Voltage: +/-5% of the nominal value
Frequency: +/-2% of the nominal value
ATTENTION!
Power from lines with values outside the indicated limits can damage the electrical components.
C3. WORKING CYCLE
The pumps are designed for continuous use under maximum back pressure.
ATTENTION!
Functioning under by-pass conditions is only allowed for brief periods of time (2-3minutes maximum).
C4. FLUIDS PERMITTED
PERMITTED
• Chemical products: Urea, weak acid & weak alkaline fluid etc.
• Water
D. MOVING AND TRANSPORT
Given the limited weight and size of the pumps (see overall dimensions), moving the pumps does not require the use of lifting devices.
The pumps were carefully packed before shipment. Check the packing material on delivery and store in the dry place.
WARNING:
Read carefully and understand all INSTRUCTIONS before operating.
Failure to follow the safety rules and other basic safety precautions may result in serious
personal injury.
MODEL NUMBER: 10302500, 10302501, 10302502, 10302503, 10302504, 10302505
REV 02/27/14
E. INSTALLATION
E1. DISPOSING OF THE PACKING MATERIAL
The packing material does not require special precautions, not being in any way dangerous or polluting.
Refer to local regulations for its disposal.
E2. PRELIMINARY INSPECTION
• Check that the machine has not suffered any damage during transport or storage.
• Clean the inlet and outlet openings, removing any dust or residual packing material.
• Make sure that the motor shaft turns freely.
• Check that the electrical specifications correspond to those shown on the identification plate.
1 of 4
UREA/DEF AC Transfer Pump Ki
USER’S MANUAL
MODEL NUMBER
10302500 & 10302501 & 10302502 &
10302503 & 10302504 &10302505
E. INSTALLATION
UREA/DEF AC TRANSFER PUMP
USER’S MANUAL
MODEL NUMBER
10302500 & 10302501 & 10302502 &
10302503 & 10302504 &10302505
J.DIMENSIONAL DATA
ATTENTION!
326
205
306
THE MOTORS ARE NOT OF AN ANTI-EXPLOSIVE TYPE. Do not install them where inflammable vapours can be present.
E3. CONNECTING
• Before connection, make sure that the tubing and the suction tank are free of dirt and thread residue that could damage the pump and
its accessories.
• Do not use conical threaded joints that could damage the threaded pump openings if excessively tightened.
Step 1: SUCTION HOSE:
- Connect the 1.5M Suction hose by the Hose tail (#8) and Clamp (#12) to the inlet of the pump.
Step 2: DELIVERY HOSE:
- Connect the 6M Delivery hose by the Hose tail (#8) and Clamp (#12) to the outlet of the pump or the flow meter.
Step 3: FLOW METER (Optional):
- Connect the flow meter by the Elbow (#9) to the outlet of the pump.
Step 4: NOZZLE
- Connect the dispensing nozzle by the Clamp (#12) to the delivery hose.
E4. DISPENSING
After installation the completed pump system as picture indicated, connect the power supply, start dispensing.
ATTENTION!
It is the installer’s responsibility to use tubing with adequate characteristics.
Loosening of the connections (threaded connections, flanging, gasket seals) can cause serious ecological and safety problem.
Check all the connections after the initial installation and on a daily basis after that.
Tighten the connections, if necessary.
F. DAILY USE
a. If using flexible tubing, attach the ends of the tubing to the tanks. In the absence of an appropriate slot, solidly grasp the delivery tube
before beginning dispensing.
b. Before starting the pump, make sure that the delivery valve is closed
(dispensing nozzle or line valve).
c. Turn the ON/OFF switch to ON. The by-pass valve allows functioning with the delivery closed only for brief periods.
d. Open the delivery valve, solidly grasping the end of the tubing.
e. Close the delivery valve to stop dispensing.
f. When dispensing is finished, turn off the pump.
K. PROBLEMS AND SOLUTIONS
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
The Motor is not turning
Lack of electric power
Check the electrical connecting
The motor turns slowly when starting
Motor Problems
Contact the Service Department
Low voltage in the electric power line
Bring the voltage back within the anticipated
limits
Low level in the suction tank
Filter clogged
Excessive suction pressure
ATTENTION!
Function with the delivery closed is only allowed for brief periods (2-3 minutes maximum).
After using, make sure the pump is turned off.
Lower the pump with respect to the level of
the tank or increase the cross-section of the
tubing
High loss of head in the delivery circuit Use shorter tubing or of greater diameter
(working with the by-pass open)
By-pass valve blocked
G. PROBLEMS AND SOLUTIONS
Dismantle the valve, clean and/or replace it.
Air entering the pump or the suction tubing Check the seals of the Connections
H. MAINTENANCE
All models are designed and constructed to require a minimum of maintenance.
In any case always bear in mind the following basic recommendations for a good functioning of the pump:
- On a weekly basis, check that the tubing joints have not loosened, to avoid any leakage.
- On a monthly basis, check the pump body and keep it clean of any impurities.
- On a weekly basis, check and keep clean the line suction filter.
- On a monthly basis, check that the electric power supply cables are in good condition.
Use tubing suitable for working under
suction pressure
Low rotation speed
Check the voltage at the pump. Adjust the
voltage and/or use cables of greater crosssection
The suction tubing is resting on the bottom Raise the tubing
of the tank
Increased pump noise
I. NOISE LEVEL
Under normal working conditions the noise emission from all models does not exceed the valve of 80 db at a distance of 1 meter from
the electric pump.
A narrowing in the suction tubing
Leakage from the pump body
Cavitation occurring
Reduce suction pressure
Irregular functioning of the by-pass
Dispense fluid until the air is purged from
the by-pass system
Diaphragm damaged
Check and replace the diaphragm
J. DISPOSING OF CONTAMINATED MATERIALS
In the event of maintenance or demolition of the machine, do not disperse contaminated parts into theenvironment.
Refer to local regulations for their proper disposal.
2 of 4
3 of 4
UREA/DEF AC Transfer Pump Kit
USER’S MANUAL
MODEL NUMBER
10302500 & 10302501 & 10302502 &
10302503 & 10302504 &10302505
7
14
15
16
4
5
6
7
8
9
3
2
10
1
13 12
11
K. DIAGRAM AND PARTS LIST
No.
Description
Qty
No.
Description
Qty
1
Crash gasket
4
9
Delivery hose
6.5m
2
Bracket
1
10
Nut
2(4)
3
Bolt
4
11
Nut
4
4
Nozzle
1
12
Hose clamp
3
5
Nozzle holder
1
13
Suction hose
1.5m
6
Electric pump
7
O-ring
8
Hose tail
1
14
Elbow
1
2(4)
15
Circlip
2
3
16
Flow meter
1
4 of 4
Size: 145x210mm
REV 02/27/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement