C003 Heavy Duty Hand Tool Operating Instructions - Band

C003 Heavy Duty Hand Tool Operating Instructions - Band
Operating
Instructions
C003 Heavy Duty
Hand Tool
1. Band may be used from bulk roll as this
completely eliminates waste of band. Slide
buckle on band as shown, bringing end of
band around object to be clamped and
again through buckle.
2. Continue band around object once
more and again through buckle.
Double banding develops a great deal
more radial compression than single
banding. Bend end of band under
buckle.
3. Place band in open of tool nose and
gripper block. Move into slot as far as
possible, to avoid buckle sliding into tool
nose. Apply tension by turning handle of
tool.
4. Place finger on BAND-IT Band at buckle
bridge while tensioning with tool handle.
When you feel BAND-IT Band stop moving
through buckle as you are turning handle,
maximum pressure is being exerted by the
BAND-IT Band around object being
clamped. Stop turning handle.
5. Roll tool over buckle, backing off with
tension handle1- 1½ turns throughout entire
rolling operation. Failure to back off tension
with tension handle throughout entire course
of roll-over may result in breaking of band.
There is no loss of tension as band released
is used up in the bend.
6. Pull cutting handle to cut the band.
When applying Giant Band clamps, prior
to cutting off clamp, release band gripper
and push tool nose away from buckle
approx. ¼”.
7. Remove tool,
holding stub of band
down with thumb.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 1 of 3
8. Clinch stub by
hammering
down buckle
ears, completing
BAND-IT clamp.
Document # P91687 rev. B
© Copyright
BAND-IT-IDEX, Inc. 2003
All rights reserved
Cleaning and
Warranty
C003 Heavy Duty
Hand Tool
Gripper Cleaning Instructions:
1. Remove gripper. Align gripper pin
hole with notch in tool frame. Using a
punch and hammer, punch pin out of
slide block.
2. Using a wire brush, clean all
foreign matter from teeth.
3. Replace pin. Gripper spring must be
seated in tension screw hole. Align
gripper hole with slide block hole, insert
pin in hole and hammer pin in place.
NOTE: Periodically apply white lubricant or equivalent to tension screw thread (Item 6 on page 3)
to prevent excessive wear.
If tool fails to securely grip tail of clamp, follow gripper cleaning instructions above.
Unless sold without warranty, BAND-IT products are warranted to be free from defective
workmanship and/or materials for a period of one year from the date of purchase. Warranty on
tools is void if clamps not meeting BAND-IT specifications are used, or if the tool is altered or
abused in any manner, including lack of lubrication or used for any purpose in any way not
intended by the manufacturer as specifically covered by the instructions accompanying the tool.
Specific tool components, such as knives, blades and grippers, which are subjected to normal
wear, are excluded from this coverage, as component life depends on usage of the tool. Tools
that are repaired or sold as used by BAND-IT are subject to a warranty of 90 days from date of
shipment. NO OTHER WARRANTY OF ANY KIND WHATSOEVER, EITHER ORAL OR
WRITTEN, INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OTHER WARRANTY OF QUALITY IS EITHER EXPRESSED
OR IMPLIED FOR THE PERFORMANCE OF BAND-IT PRODUCTS. BAND-IT SHALL NOT
BE LIABLE FOR SPECIAL, INCIDENTAL, AND/OR CONSEQUENTIAL DAMAGES, EVEN IF
BAND-IT HAS BEEN NOTIFIED OF THE POTENTIAL OF SUCH LOSS OR CLAIM. (8/02)
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 2 of 3
Document # P91687 rev. B
© Copyright
BAND-IT-IDEX, Inc. 2003
All rights reserved
Tool Assembly
Parts List
C003 Heavy Duty
Hand Tool
1. To assist in removing threaded parts,
apply heat (softens locking compound).
2. When connecting item 6 (tension
screw) to item 3 (slide block), clean
threads (male and female) of foreign
matter, then apply two drops of high
strength locking compound (loctite 271 or
equiv.) onto male threads and connect
parts together. Apply 3 oz. Of white
lubricant or equiv. to tension screw
thread.
3. When connecting item 15 (set screw)
to item 16 (cutter bar), clean threads
(male and female) of foreign matter, then
apply one drop of medium strength
locking compound (loctite 242 or equiv.)
Onto male thread and connect parts
together.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
C00369 BAND-IT TOOL, REPAIR PARTS LIST
ASSY #
ITEM
DESCRIPTION
C02187
1
TOOL FRAME
C07087
2
THRUST BEARING
3
SLIDE BLOCK
4
PIN, ECC. LEVER PIVOT
C06799
5
BAND GRIPPER
6
TENSION SCREW
7
GRIPPER SPRING
8
SPIN GRIP
9
EXTERNAL RETAINING RING
C04799
10
BUSHING, TENSION HANDLE
11
TENSION HANDLE
12
SET SCREW, HALF DOG
13
CUTTER BAR HANDLE
14
VINYL GRIP
C05887
15
SET SCREW
16
CUTTER BAR
www.BAND-IT-IDEX.com
Page 3 of 3
QTY
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
Document # P91687 rev. B
© Copyright
BAND-IT-IDEX, Inc. 2003
All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement