J050 - Heavy Duty Adapter Operating Instructions

J050 - Heavy Duty Adapter Operating Instructions
Operating
Instructions
J050 - Heavy
Duty Adapter
To Install a BAND-IT Junior Clamp using the Heavy Duty Adapter:
Screw Block
Cutoff Screw
Setscrew
1
2
Place Heavy Duty Adapter on nose of BAND-IT tool,
positioned as shown. Cut-off screw should not extend
beyond bottom of screw block. Line up tool and
adapter slots and tighten two setscrews. Insert
BAND-IT Junior or Junior SID clamp tail into adapter
nose through all slots and grip end with band gripper
lever.
3
4
When properly tensioned, roll tool over hose, backing
off tension handle ¼ to ½ turn only, through course of
rollover, (depending on type and size of hose) until
shear hook grips buckle edge. Tighten knurled nut by
hand, securing buckle tightly between edge of hook
and nose of adapter.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
Install clamp over hose assembly. Tension
clamp by turning the handle of BAND-IT Tool
clockwise.
Place ratchet wrench on hex nut. Operate wrench
clockwise until clamp is sheared. Clamp is now
locked and completed.
NOTE: USE OF A VISE IS OPTIONAL
TO HOLD TOOL DURING USE.
www.BAND-IT-IDEX.com
Page 1 of 2
Document # P35387 rev. D
© Copyright
BAND-IT-IDEX, Inc. 2005
All rights reserved
Repair Parts &
Assembly
J050 - Heavy
Duty Adapter
SEE NOTE 3
6
12 REF
7
8
BLADE INSTALLATION
NOTES:
J050 HEAVY DUTY ADAPTER, REPAIR PARTS LIST
1. TO ASSIST IN REMOVING THREADED
PARTS, APPLY HEAT TO SOFTEN LOCKING
COMPOUND.
2. WHEN CONNECTING ITEM 4 (KNOB) OR
ITEM 2 (NUT) TO ITEM 3 (SCREW), CLEAN
THREADS (MALE AND FEMALE) OF
FOREIGN MATTER, THEN APPLY ONE
DROP OF MEDIUM STRENGTH LOCKING
COMPOUND (LOCTITE 242 OR
EQUIVALENT) ONTO MALE THREAD AND
CONNECT PARTS TOGETHER.
BAND-IT
PART #
J11985
J06887
J00587
J93099
J00987
3. PERIODICALLY CHECK FOR TENSION ON
THESE SCREWS. LOOSENED SCREWS
WILL RESULT IN ASSEMBLY BREAKAGE.
J05187
J06787
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
DESCRIPTION
RATCHET WRENCH
HEX NUT
JR ADAPTER SCREW
KNOB
SHEAR HOOK
SCREW, SPECIAL
BACKING PLATE
CUTTER BLADE
HEX KEY, SPECIAL
PIN, GROOVED
PIN, GROOVED
BODY
SOCKET HEAD SCREW
SCREW BLOCK
QTY
1
1
1
1
1
2
1
1
1
1
2
1
2
1
Refer to website for warranty information: http://www.band-it-idex.com/warranty.html
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-627-3925
www.BAND-IT-IDEX.com
Page 2 of 2
Document # P35387 rev. D
© Copyright
BAND-IT-IDEX, Inc. 2005
All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement