0.07.B.0020 I5 user guide insert-6Jul2012-NG

0.07.B.0020 I5 user guide insert-6Jul2012-NG
1.
The first step when installing the i5 infrared beams is to
obtain maximum alignment.
The transmitter and receiver are typically mounted
directly opposite one another, but some leeway is
given in the form of a wide beam being cast should
absolute alignment not be possible
Do not in any way modify the components of the system.
Do not leave packing materials (plastic, polystyrene, etc.)
within reach of children as such materials are potential
sources of danger.
4.
Dispose of all waste products like packaging materials,
according to local regulations.
5.
CENTSYS does not accept any liability caused by improper
use of the product, or for use other than that for which the
automated system was intended.
6.
This product was designed and built strictly for the use
indicated in this documentation. Any other use, not
expressly indicated here, could compromise the service
life/operation of the product and/or be a source of danger.
7.
Anything not expressly specified in these instructions is not
permitted.
Option 2: Reticulated
wire
Tx
750mm*
10b.The cable can also
be routed through
the hole in the
moulding of the
back of the
enclosure.
Remove cover and prepare for mounting
PCB connections
It is very important to align the transmitter and the
receiver beams. Under certain conditions (distance
>10m) it may be necessary to fit the cover to achieve
alignment
Screw-hole
cover
Transmitter
3. Icons used in this guide
11. Terminate wires on
to the transmitter
PCBs prior to
clipping back into
enclosure as shown
in the wiring
diagram.
Fastener
This icon denotes variations and other aspects that
should be considered during installation
This icon indicates warning, caution or attention!
Please take special note of critical aspects that
MUST be adhered to in order to prevent injury
4. Operation
Cover
2.
Unclip screw-hole
cover piece.
3.
Unscrew cover
retaining fastener.
4.
Lift off cover.
5.
Unclip PCB and
remove.
6.
Place self-adhesive
pads onto back of
enclosure
Power supply
12V - 24V DC/AC
Power consumption
Power consumption
Transmitter - 21mA,
Receiver - 43mA @ 12V
Maximum distance
40m
Alignment
Automatic - 9m2 @ 10m#
Output contact rating
Output contact rating
5A @ 220V AC (non
inductive)
N/C
M7
COM
+
_
Green
Led
M7
324
eZ8X005
J31CG
PCB
Self-adhesive
pads
5. Technical specifications
NT72C-S10
Relay
N/O
Receiver
12. Terminate wires on
to the receiver PCBs
prior to clipping
back into enclosure
as shown in the
wiring diagram.
13. Replace the cover
and screw back the
fastener and the
screw-hole cover.
Enclosure
back
INPUT
VOLTAGE
12V - 30V
AC OR DC
CP85 V1.4 INFRA-RED TRANSMITTER
The i5 infrared beam consists of a transmitter and receiver
unit mounted on opposite sides of an entrance.
The transmitter sends a modulated infrared beam to the
receiver module. When the beam is interrupted the receiver
changes the state of an internal relay. The contacts of the
relay are potential-free and can be wired as normally-open or
normally-closed.
Cable
conduit
Cable
hole
CENTSYS recommends the height of 750mm, but the
height of the beam must be tailored to suit the
specific requirements of the installation
Ne555
eZ009
2.
Position Rx and Tx
to be in line and level
with each other
CP86 V1.6 INFRA-RED RECEIVER
SAFETY
DEVICES FOR
AUTOMATED GATES
Rx
All installation, repair, and service work to this product must
be done by a suitably qualified person.
3.
Cut-out
for cable
Cable
saddle
2. Safety Instructions
1.
10a.Route the cables
through the cable
cut-out as shown in
the illustration
providing 12-24 V
DC/AC to both the
receiver and
transmitter.
A3C
The i5 infrared beams are designed to provide optimum
safety by detecting the presence of a person or vehicle
traversing the path of a moving gate or door. The beams can
be interfaced with most automation equipment. They can
also be used to enhance the security of the automation by
enabling the Intruder Detection Alarm function inherent in
many of the later CENTSYS gate operator controllers, as well
as external alarms and buzzers by means of either a
normally-open or normally-closed potential-free contact.
Option 1: External wire
+
_
Green
Led
M7
A3U
i5 Infrared beams
Pocket installation guide
Wiring Route
6.Installation
1. Introduction
POWER
0.07.B.0020 I5 user guide
insert-6Jul2012
www.centsys.com.au
Operating temperature
15°C to 55°C
Operating humidity
0% - 90% (non condensing)
Degree of protection
IP54
J31CG
Indicators
“O” Ring
Mounting
7.
Mark position of unit.
8.
Use 5mm masonry
bit to drill hole in
wall.
9.
Mount using fastener
provided.
Fastener
Rawl plug
Height - typically 750mm
above the ground
!
Both the receiver and transmitter are fitted with a
green LED indicator
!
The LED in the transmitter illuminates when the
power supply is ON, and the receiver LED
illuminates when the beams are aligned
!
A separate wire should be used to obtain COMMON,
as this ensures the beams are tested accurately by
the Beam Test function inherent in many of the later
CENTSYS gate operator controllers
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement