advertisement
DVI
EXTENDER
DVI-ELW
(Local)
DVI-ERW
(Remote)
U
SER
M
ANUAL V1.1
DVI-EXW
Package Contents-
1x DVI-ELW Local Unit
1x DVI-ERW Remote Unit
1 user manual
2x Power adapter DC 12V with lock
1x DVI 1.2M cable (DVI-D Male to Male)
1x IR Blaster Cable(Peak Wavelength 940nm)
1x IR Receiver Cable
4x screws
8x foot pads
Any thing missed, please contact with your vendor.
Features
Through the DVI Extender, you can use one PC to display identical image and extension of DVI signal up to 100 meter on DVI monitor
Supports resolution up 1920x1200
HDCP Compliant
Support RS-232(Bi-direction transfer)
Supports all frequency band IR control
One CAT.5 cable extension
HD-baseT technology
Use CAT.5 cable to install easily
Specifications
Function DVI-ELW DVI-ERW
DVI In Connector DVI Female x 1 None
DVI Out
Connector
RJ-45 Connector
IR OUT
None
3.5ψ Stereo Jack x 1
1
IR2 IN None
DVI Female x 1
None
3.5ψ Stereo Jack x 1
Max. Resolution
Cable Distance
Power Adapter
(Min.)
Housing
Weight
Dimensions
(LxWxH)
313g
Up to 1920x1200
100 m (Max.)
DC 12V with lock
Metal
150x80x35mm
315g
-1-
LOCAL FRONT VIEW
1. IR OUT
2. HDCP LED
3. LINK LED
4. MODE LED
5. POWER LED
LOCAL REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. DVI IN
4. RS-232
REMOTE FRONT VIEW
1. IR2 IN
2. IR1 IN
3. HDCP LED
4. LINK LED
5. MODE LED
6. POWER LED
REMOTE REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. DVI OUT
4. RS-232
-2-
Installation
1. Turn off the PC and DVI monitor.
2. Connect the DVI extension cable between the PC and the “DVI IN” port of DVI-ELW.
3. Connect the DVI extension cable between the DVI monitor and the “DVI OUT” port of DVI-ERW.
4. Connect the CAT.5 cables between the DVI-ELW “LINK” port and the DVI-ERW “LINK” port of extender.
5. Connect the power cord and turn on the extender.
6. Turn on the PC and DVI monitor.
IR Receiver Cable Directions:
Put it into the DVI-ERW “IR2 IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into DVI-ELW “IR OUT” port, it sits in front of the device receiver’s IR sensor, which is located on the front-panel.
Additional Options
Select any additional options you may require.
1. IR Receiver Cable
GND
+V
Sig
2. IR Blaster Cable
NC
P+
N-
-3-
Technical Specifications Output Signal
Pin # Signal
1 T.M.D.S Data 2-
Pin # Signal
16 Hot Plug Detect
2 T.M.D.S Data 2+ 17 T.M.D.S Data 0-
3 T.M.D.S Data 2/4 Shield 18 T.M.D.S Data 0+
4 T.M.D.S Data 4-
5 T.M.D.S Data 4+
6 DDC Clock
7 DDC Data
19
20
21
22
T.M.D.S Data 0/5 Shield
T.M.D.S Data 5-
T.M.D.S Data 5+
T.M.D.S Clock Shield
8 Analog Vert. Sync
9 T.M.D.S Data 1-
23 T.M.D.S Clock+
24 T.M.D.S Clock-
10 T.M.D.S Data 1+
11 T.M.D.S Data 1/3 Shield C1 Analog Red
12 T.M.D.S Data 3-
13 T.M.D.S Data 3+
14 +5V Power
15 GND
C2
C3
C4
C5
Analog Green
Analog Blue
Analog Horz Sync
Analog Ground
Wiring Information & Coding
Conductor
Identification
Pair 1
Pair 2
Pair 3
Pair 4
RJ45 Pin
Assignment
5
4
1
2
3
6
7
8
Color Code for
Conductor
White-Blue
Blue
White-Orange
Orange
White-Green
Green
White-Brown
Brown
-4-
-5-
Note
However sometimes, especially in demonstrations or in a lab environment, the cable is rolled randomly in small turns for convenience. The randomly rolled UTP cable suffers additional signal impairments (compared to a straight cable) and therefore the maximal operating reach might be reduced.
Rolling a CAT5E cable around a 70cm fixed diameter plastic drum has just a minor effect on the FEXT (Far End
Cross Talk) when compared to a fully stretched cable.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names referred to this manual are the trademarks or registered trademarks belonging to their respective companies.
-6-
advertisement
Related manuals
advertisement