NBDVR512GW - Instruction Manual (English R5).cdr

NBDVR512GW - Instruction Manual (English R5).cdr
Instruction Manual
Ultra
1440p Quad HD Dash Cam with GPS,
Wi-Fi & Anti Glare Polarising Filter
INTRODUCTION TO USING A DASH CAM
The iN-CAR CAM range of Dash Cams have been designed specifically with ease of use in mind, it is
recommended NOT to change the default settings, which have been carefully selected to give the
best performance for day to day use.
Basic operation.
The Dash Cam is set to record video, in files of just 3 minutes in length. This means that each
video file is a manageable size should you need to download and send to your insurance company.
Eventually your MicroSD card will fill up with video files but don't worry, the camera automatically
deletes the oldest file to make space for new recordings. This way you never run out of space and
have plenty of driving historical evidence saved.
Typically a 16Gb card will store the last 2 hours of driving footage.
The Time and Date are automatically set upon the camera from satellite data, based on the Country
selected from within the First Time Use menu.
The Time and Date will also update automatically for Daylight Savings Time, again based on the
Country selected.
There are 3 modes of camera operation - Video, Photo and Playback.
Video Mode: The default mode when the camera is turned on, for video recording.
Photo Mode: Allows you to take still photographs.
Playback mode: Allows you to view recorded video or photographs upon the Dash Cam LCD screen.
Press the MODE button on the Dash Cam to select required mode.
Automatic Start / Stop Technology. The Dash Cam senses power supplied to the cigarette lighter
socket as soon as the vehicle ignition is turned on and will start to record automatically.
When the ignition is turned off, the Dash Cam will perform an automatic shutdown process.
1. Tips for capturing best video footage:
1.1 Position the Dash Cam in the centre of the windscreen and ideally behind the rear view
mirror so it is not a distraction to the driver.
1.2 Reduce the amount of sky in the picture, by angling the view of the camera towards the road.
Too much sky will make the road appear darker due to the automatic exposure compensation.
1.3 Remove unnecessary items from your dashboard. If objects are placed on your dashboard
these can cause reflections to be seen on the windscreen and these reflections may be
captured during recording.
2. Tips for stable memory card performance:
2.1 Periodically reformat the memory card. Every 2-3 weeks we recommend that you reformat
the memory card. This will wipe any files from the card and set it up afresh for continued use
with your Dash Cam.
Of course, you should only do this AFTER you've downloaded any files from the card that you
may want to keep, as formatting the card will remove all content.
2.1 Format your memory card using the Dash Cam. This will make sure that the card is
structured specifically for your camera. Press MENU twice and choose the Format Card
option. Follow the on-screen instructions accordingly.
2.2 Switch off the Dash Cam before removing the SD memory card, to prevent the chance
of damage being caused to the memory card or the files stored upon it, turn OFF the
Dash Cam before removing or inserting the memory card.
03
TABLE OF CONTENTS
INTRODUCTION TO USING A DASH CAM
............................................................. 03
TABLE OF CONTENTS ................................................................................................. 04
PRECAUTIONS ............................................................................................................. 05
CAUTIONS ON USING THIS PRODUCT ...................................................................... 05
PRODUCT SPECIFICATION ......................................................................................... 06
PACKAGE CONTENTS ................................................................................................. 07
PRODUCT FEATURES ................................................................................................. 07
POWERED GPS MOUNT .............................................................................................. 08
CAMERA - PARTS & CONTROLS ................................................................................. 09
IN VEHICLE INSTALLATION ......................................................................................... 14
FIRST TIME USE ........................................................................................................... 18
POLARISING FILTER .................................................................................................... 19
VIDEO MODE ................................................................................................................ 20
PHOTO MODE .............................................................................................................. 25
PLAYBACK MODE ........................................................................................................ 27
SETUP MENU ................................................................................................................ 31
PC CONNECTION ......................................................................................................... 35
VIDEO & AUDIO OUTPUT .............................................................................................. 36
TROUBLE SHOOTING ................................................................................................... 37
04
PRECAUTIONS
Please read this manual carefully before operation and keep it for future reference. It will be helpful
should you encounter any operational problem.
WARNING: Do not expose this product to rain, moisture or water under any circumstances, doing
so may result in the risk of electric shock or fire.
CAUTION: To reduce the risk of electric shock, do not perform any servicing other than that
contained in the instruction manual unless you are qualified to do so.
Have the unit serviced by a qualified service technician if;
The Unit has been exposed to rain or water.
The unit does not seem to operate normally.
The unit exhibits a marked change in performance.
LCD: A Liquid Crystal Display (LCD) screen is a multilayer complex component, containing
691,200 pixels. Pixels can however fail during normal product life. 1 pixel = 0.0001%
failure rate, and one pixel failure per year of operation is considered normal and not
a cause for concern.
WEEE: Disposal of Waste Electrical and Electronic Equipment and/or Battery by users
in private households in the European Union.
This symbol on the product or on the packaging indicates that this cannot be disposed
of as household waste. You must dispose of your waste equipment and/or battery by
handing it over to the applicable take-back scheme for the recycling of electronic
equipment and/or batteries. For more information please contact your local household
waste disposal office.
CAUTIONS ON USING THIS PRODUCT
1. Ensure that the windscreen is free of dirt or grease before placing mount upon it.
2. Do not obscure the view of the road ahead or impede the deployment of any airbags in the event
of an accident.
3. When not in use, please disconnect the car adaptor from both the 12/24Vdc outlet in your vehicle
and the device itself.
4. Only clean the device with a soft dry cloth, for tough dirt, apply some neutral detergent diluted in
5 to 6 parts water to a soft cloth.
Note that alcohol, thinner, benzene etc could cause damage to the paint or coatings.
5. Avoid making contact with the lenses as damage may be caused.
6. If required clean the glass lens carefully using spectacle lens cleaning fluid on a soft cloth only.
7. The video recordings made by this Digital Video Recorder are intended for personal use only.
8. Publication of the recordings on Youtube, the internet or other methods are subject to the
Data Protection Act and the requirements thereof must be adhered to.
If the Digital Video Recorder is to be used within a commercial environment, i.e. truck use, then
the CCTV regulation apply also, in addition to the Data Protection Act regulations. This includes
labelling to identify the use of CCTV is taking place, the omission of Audio recording and
informing the relevant authorities of who controls the data.
9. Video playback upon the device which is visible to the driver is prohibited or restricted in some
countries or States. Please adhere to these laws.
10. Whilst driving, do not adjust the controls of your device as this is a distraction to driving.
05
PRODUCT SPECIFICATION
Model Number / Name
NBDVR512GW / ULTRA
Power Requirements
5V / 1.5A
Power Supply
12-24Vdc Car Power Cable (supplied)
Fuse Type: 20mm / 2A
Output: 5Vdc
Sensor Resolution
6.8M Pixel (6,798,816 Pixels)
Lens Type / Angle / Aperture
6G / 140° / F1.6
Recording Resolution
2560 x 1440 @ 30fps (default)
Screen Size
3.0"
Screen Resolution
960 (W) X 240 (H) pixels x RGB
Screen Ratio
16:9
Card Reader
MicroSD, Class 6-10, up to 64GB
SD Card
(Recommended Type)
8-64GB MicroSD Card, Class 10 (48mb/s), for best results use a
recognized brand
SD Card Recorded File
Capacity
(based on default settings)
8GB Micro SD = 45mins of recording (15x 3 minute recordings)
16GB Micro SD = 90mins of recording (30x 3 minute recordings)
32GB Micro SD = 180mins of recording (60x 3 minute recordings)
64GB Micro SD = 360mins of recording (120x 3 minute recordings)
Recording Format
MOV
Video / Audio Out
High Definition: Type C Socket (Video / Audio)
Standard Definition: 3.5mm Jack (Video / Audio)
Internal Battery
Lithium-ion 3.7V / 260mAh (approx. 30mins recording time)
Battery design allows the 'Auto Power Off' feature to function in
event of power loss within the vehicle. It is not intended as an
alternative power source to replace the supplied car adaptor.
Unit Dimensions
106 x 59 x 40mm
Unit Weight
89g
Android is a trademark of Google Inc. in the United States and other countries.
Mac is a registered trademarks of Apple Inc. in the United States and other countries.
iOS is a trademark or registered trademark of Cisco in the United States and other countries.
© 2015 Google Inc. All rights reserved. Google Maps™ mapping service is a trademark of Google Inc.
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
Exmor R is a trademark of Sony Corporation.
STARVIS is a trademark of Sony Corporation.
06
PACKAGE CONTENTS
Please check the contents of your NEXTBASE product.
Dash Cam
Powered GPS Mount
Car Power Cable
USB Cable
(adhesive mount included)
Window
Sticker
Quick Start
Guide
Instruction Manual
& Software Disk
Product appearance may differ slightly to that shown above.
PRODUCT FEATURES
Thank you for purchasing this NEXTBASE Dash Cam, in this section we will outline some of the
features available with this Dash Cam.
3.0" LCD Colour Screen
LCD screen for ease of use and viewing the playback of recorded videos and photos.
Powered GPS Mount
Supplied with an Easy-Fit powered mount, which allows the Dash Cam to be fitted and removed
quickly and easily. The car power cable can remain in place, connected to the mount.
GPS Logger
GPS co-ordinates, date and time are recorded, the journey can then be viewed using the supplied
Windows & Mac playback software.
The software is also available to download from www.nextbase.co.uk
Wi-Fi Connectivity
Connect your smartphone or tablet device to the Dash Cam, can be used to Start/Stop recording
or to view or download files from the Dash Cam.
G Sensor / File Protection
In the event of an impact the device will automatically 'protect' the recording, stopping the file from
being over-written. This can also be performed manually, by pressing the ‘protect’ button.
Individual files can also be 'protected' when viewed within playback mode.
Intelligent Parking Mode
Once enabled, Parking Mode will put the Dash Cam in to standby mode after 5 minutes of inactivity.
The Dash Cam will power on automatically and record 2 minutes of video, when physical movement
of your vehicle is detected.
Polarising Filter
This Dash Cam incorporates a polarising filter to reduce windscreen glare and reflection.
Auto Dimming
Once enabled, the screen will automatically dim during night-time driving.
07
POWERED GPS MOUNT
Please see below to identify the parts of the supplied powered mount.
5
1
4
2
3
1.
Locking lever
The locking lever is used to attach and release the window mount to your vehicles windscreen.
Pull the lever down to prepare the window mount for use. Once the mount is firmly upon the
windscreen (in a suitable location) push the lever to lock the mount in place.
2.
Locking ring
Loosen the locking ring to adjust the Dash Cam position if required, remembering to
re-tighten before use.
3.
DC-IN socket
Connect the supplied car power cable here.
4.
Suction cup
This is used to attach and release the window mount to your vehicles windscreen.
Affix to a clear piece of windscreen where there is no paint effect applied.
5.
Suction release tab
Once the locking lever has been opened use this release tab to break the seal between
the mount and windscreen.
08
CAMERA - PARTS & CONTROLS
Please see below to identify the parts and controls of your Dash Cam.
Front:
1
2
3
1.
Mounting point (located under the dust cover)
After removing the dust cover, attach the supplied powered GPS mount here.
2.
Speaker
Integral speaker for audio playback directly from the Dash Cam.
3.
Camera lens
Wide Angle 140°, 6 Element glass lens for optimum picture quality.
09
CAMERA - PARTS & CONTROLS (CONTD.)
Back:
4
10
5
11
6
12
7
8
9
4.
Power On / Off
Press and hold for 2 seconds to turn on / off the Dash Cam.
5.
Up / Microphone Off
Up:
Press to navigate up within menus and to move to the previous file when in playback mode.
Microphone Off:
Press to turn off / on the microphone (audio recording), only available whilst in video mode.
6.
Down / Screen Off
Down:
Press to navigate down within menus and to move to the next file when in playback mode.
Screen Off:
Press to turn off / on the screen, only available whilst in video mode.
7.
Protect File / Wi-Fi
Protect File:
Press whilst recording to protect the current file in event of an emergency situation.
Note:
- To help locate the Protect button, there are ‘pips’ to the left hand side of the button.
Wi-Fi:
Press and hold for three seconds to turn on Wi-Fi mode, this is not available whilst recording
or during playback.
Note:
- To exit Wi-Fi mode please press the OK button once paired device has been disconnected.
10
CAMERA - PARTS & CONTROLS (CONTD.)
Continued from previous page.
4
12
5
11
6
10
7
8
9
8.
Dual colour LED indicator
Red = power on
Red flashing = recording
Blue = battery charging
9.
Screen
3.0' LCD colour screen for the viewing of recorded files on the Dash Cam.
10. Mode
Press to change between video, photo or playback modes.
11. Record / OK
Record:
Press to start or stop a recording when in video mode, or take a photo when in photo mode.
OK:
Press to confirm selection when in menus.
12. Menu
Press to open the menu within current mode, press twice to open the Setup menu.
11
CAMERA - PARTS & CONTROLS (CONTD.)
Top:
13
14
13. Rear Camera input (located under the dust cover)
Used to connect an auxiliary rear camera (sold separately), contact your local Nextbase dealer
for availability.
Note:
- Failure to use the approved Nextbase Rear Camera, will result in damage being caused
which will not be covered under the manufacturers warranty.
14. DC-IN & USB socket (located under the dust cover)
Connect the supplied car power cable or USB data cable here.
Note:
- Normally the car power cable is connected to the mount when in use, not directly to
this socket.
Bottom:
15
16
15. Light Sensor
Detects the ambient light level and will adjust the screen brightness accordingly. Turned on and
off within the Setup Menu.
16. Reset button
In the unlikely event the Dash Cam becomes unresponsive, press the RESET button to
restart the Dash Cam.
12
CAMERA - PARTS & CONTROLS (CONTD.)
Sides:
18
19
17
17. HD Output (located under the dust cover)
Used to connect your Dash Cam to a television using an HD Cable (sold separately).
18. Microphone
Integral microphone for audio recording.
19. MicroSD Card slot
Insert the MicroSD card here, taking care that the gold contacts are facing towards the back
of the Dash Cam.
13
IN VEHICLE INSTALLATION
Please follow the instructions below for first-time installation of the Dash Cam. For day to day use
simply remove the camera from the mount as required.
1.
Insert MicroSD Card
Insert a suitable MicroSD card (Class 10 48/Mbps) in to the Dash Cam, taking care that the
gold contacts are facing towards the LCD screen side of the Dash Cam. Push the memory
card until it clicks into place.
Note:
- Use the edge of a small coin (or similar object) to push the memory card in place if required.
Take care that card has 'clicked' into place, a second push inwards will release the memory
card.
- Do not remove or insert the memory card when the Dash Cam is turned on. This may
damage the memory card.
2.
Remove dust cover from Dash Cam
Remove the dust cover that is located on the top of the Dash Cam to gain access to the
mounting point.
To remove the dust cover, slide it forwards away from the LCD screen of the Dash Cam.
Note:
- If the Dash Cam is not to be used for a period of time please replace the dust cover to
help keep the metal contacts free of dust or other contaminants.
14
IN VEHICLE INSTALLATION (CONTD.)
3.
Attach the mount to the Dash Cam
Slide the Dash Cam onto the mount. Once attached magnets within the mount will hold the
two parts together.
4.
Attach the mount to the windscreen
Remove the protective plastic film from the suction cup of the mount.
Select a suitable position for the mount and clean the windscreen with a dry / clean cloth to
achieve a good contact between the glass and suction cup.
Release the locking lever of the mount by pulling down and then whilst holding the suction
cup onto the glass push the lever up to secure the mount to the windscreen.
To use the supplied adhesive mount, simply unscrew the locking ring and pull the mount apart.
Replace the sucker mount, remembering to tighten the locking ring securely.
Note:
- Choose a smooth glass area without painted effect.
- Please ensure that once mounted the Dash Cam will be located within the area of the
vehicles windscreen wipers to maintain a clear view during rainfall.
15
IN VEHICLE INSTALLATION (CONTD.)
5.
Connect car power cable
Connect the supplied car power cable to DC-IN socket of the mount.
Plug the power cable into the 12-24Vdc outlet of your vehicle.
12-24V DC
The above diagram is for illustration purposes only.
The Dash Cam will automatically power on and start recording once power is available.
In some vehicles this will be when connections are made, for others the Dash Cam will
power on once the ignition has been turned on.
Should your vehicle not have a 12-24Vdc outlet, but does have a 5Vdc USB Outlet, this can be
used instead. Connect the USB cable supplied with your Dash Cam in place of the car power
cable. Ensure you connect the USB cable to the Powered Mount only, NOT directly to the
camera when using in–car
Note:
- Do NOT wire the Dash Cam directly to a 12V supply by cutting the cigarette plug
off the end of the cable, or damage will result.
- A Nextbase hardwire kit is available from your retailer. This connects directly to the
vehicle fusebox and hence leaves your cigarette socket available for Phone / Sat Nav
charging. The Nextbase hardwire kit includes the necessary 12-24VDC to 5Vdc
convertor and battery protection circuitry.
16
IN VEHICLE INSTALLATION (CONTD.)
Please read and follow the notes below for the safe operation of your Dash Cam within your
vehicle.
As per the installation instructions, you must install the Dash Cam so it does NOT obstruct the
drivers view of the road, preferably on the passenger side of the vehicle and behind the rear view
mirror. Whilst the Dash Cam clearly needs to view through the windscreen in an area swept by the
windscreen wipers, the Dash Cam should be installed so as not to intrude significantly within the
wiped area. A 40mm intrusion into the green wiped area is the maximum permitted by law.
Do NOT mount the Dash Cam in front of the driver, as depicted by the red area in the above
illustration.
When installing the Dash Cam in a vehicle, always place the device securely against the
windscreen and where possible conceal the power cable under trim. Make sure that the Dash Cam
power cable does not interfere with the drivers operating controls, such as the steering wheel, pedals
or gear levers.
Do NOT mount the Dash Cam in front of an airbag field of deployment or in a position to obscure
any mirrors.
Clean the windscreen at the point of location, prior to fitting the Dash Cam, also, applying some
moisture to the suction cup may be beneficial, to ensure absolute adhesion.
It is recommended NOT to operate the Dash Cam whilst driving. The automatic Start-Stop
technology incorporated within the device negates any need to operate the controls whilst driving.
Adjust any settings or review recordings whilst stationery, not whilst driving.
Only use your mobile device whilst stationery, not whilst driving.
After the preliminary SETUP has been carried out upon the Dash Cam, adjust the Screen Saver
setting to 1 minute, this will blank the screen automatically shortly after starting the vehicle and
therefore the screen will NOT be a distraction in any way to the driver.
17
FIRST TIME USE
To ensure the set up of this Dash Cam is as quick and simple as possible, there is an easy to follow
‘First Time Use’ menu.
This menu is used to set your preferred Language, Country (this defines your time zone) and speed
units.
The menu is available when 1) The Dash Cam is first turned on.
2) There has been a Firmware update applied to the Dash Cam.
3) After the Dash Cams settings have been reset, by using the ‘Defaults Settings’ option
within the Setup Menu.
Simply follow the on screen instructions to select the Language, Country and Speed Units.
The settings that influence the displayed time & date will be applied upon receiving a GPS connection.
Note:
- Whilst the First Time Use menus adjust the settings within the Dash Cam, the settings can still be
adjusted thereafter, by using the normal Setup Menu options. Changing country location is one
such example of a change you could make, after the First Time Use setup.
18
POLARISING FILTER
This Dash Cam incorporates a polarising filter to reduce windscreen glare and reflection, often seen
on recordings.
In bright sunlight the filter will also enhance the colour and contrast levels to help capture important
number plate detail.
The filter has a rotating bezel, so you can adjust the polarising filter exactly how you need in your
vehicle.
To set the polarising filter, place a piece of paper on your dashboard below the rear view mirror, but
away from the windscreen. With the camera turned ON, you will see the reflection of the paper in the
LCD screen of the Dash Cam. Rotate the front ring of the polarising filter to reduce reflection to the
lowest possible level. This dramatically improves the recorded image quality.
Note:
- Do not place fingers on the glass lens of the filter.
- Do not adjust the filter whilst in control of the vehicle.
19
VIDEO MODE
The key below explains the various information displayed on the screen when your Dash Cam is in
Video mode, some icons will only be displayed once the relevant function has been selected within
the Video menu, as described below.
1
2
5
4
3
6
7
2:37
14
3M
8
16:04:37 14/10/2015
13
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
12
10
11
9
Mode: indicates the Dash Cam is in Video mode.
Recording: appears on screen when recording is in progress.
Resolution: displays the current resolution.
Exposure: displays current Exposure level setting.
Video Length: displays the length of the individual recordings in minutes.
Parking Mode: appears on screen when Parking Mode has been turned on.
Microphone: displayed on screen when Audio Recording is active.
Time Lapse: appears on screen during Time Lapse recording.
GPS: The satellite icon will flash whilst the Dash Cam locates satellites. Once a stable
signal is received, the icon will stop flashing and remain on screen.
Date: current date.
Time: current time.
Memory Card: indicates whether a memory card is present.
Battery: indicates whether Dash Cam is running on battery or external power.
Protected: shown on screen when a video file has been protected by activation of the
G Sensor or by the pressing of the file protect button.
The default settings within the Dash Cam have been set to allow you to use the Dash Cam
without the need to change any settings.
See the next page for video menu settings, should you want to make any adjustments however.
20
VIDEO MODE (CONTD.)
Video Menu
The Video Menu is accessed by pressing the MENU button whilst in video mode.
Video Menu
Resolution
Exposure
Audio Recording
Number Plate
MENU Back
OK
Enter
The default settings have been carefully selected to allow you to use the Dash Cam without the
need to change any settings. However, should you wish to change a setting then please see below.
Use the up and down buttons to highlight the function that you'd like to change and press the OK
button to enter the settings sub-menu.
Once in the sub-menu, use the up and down buttons to highlight the required setting and then press
OK to confirm your selection and return to the Video Menu.
Press the MENU button twice to return to video mode.
Note:
- Menus are not accessible whilst the Dash Cam is recording.
1.
Resolution
Select recording resolution, this will increase or decrease the quality of the recorded video.
Options: 1440P, 1080P 60FPS, 1080P and 720P
Default Setting: 1440P
Note:
- The 1080P 60FPS setting will remain at 30fps during night-time recording, due to the
low level light conditions.
2.
Exposure
Adjust exposure level for different light conditions.
Options: +2, +1, 0, -1 and -2
Default Setting: 0
3.
Audio Recording
Turn On / Off the microphone.
Options: On and Off
Default Setting: On
21
VIDEO MODE (CONTD.)
Continued from previous page.
Video Menu
Number Plate
Video Length
Time Lapse Recording
Parking Mode
MENU Back
OK
Enter
4.
Number Plate
Enter the registration number for your vehicle, this will then be shown on the video file.
5.
Video Length
Select the duration of the individual recorded video files. The Dash Cam will continue
recording, filling the memory card. When the memory card becomes full, the oldest file will
be automatically deleted to make space for the new recording.
Note:
- Protected files will never be deleted.
Options: 2 Minutes, 3 Minutes and 5 Minutes
Default Setting: 3 Minutes
6.
Time Lapse Recording
Time Lapse recording is a technique whereby the frequency at which file frames are captured
(frame rate) is lower than that used when playing back the recording.
Time Lapse recording can be considered the opposite of slow motion, as when the recording
is played back time appears to be moving faster.
For example, a recording taken over three minutes would be played back as a 30 second
movie.
Options: 3 Minutes, 2 Hours and Off
Default Setting: Off
Note:
- Time lapse is considered as a leisure activity setting and not for use in order to collect
evidence in the case of an incident / accident. Time Lapse should be turned off for normal
driving conditions.
- This is the recorded file length in real time, NOT playback time. Playback time will be
1/6th of the live recording time.
22
VIDEO MODE (CONTD.)
Continued from previous page.
Video Menu
Parking Mode
Rotate Display
Time & Date Stamp
Number
Plate
Speed
Stamp
MENU Back
7.
OK
Enter
Parking Mode
When Parking Mode has been turned on, the Dash Cam enters standby mode when the
12Vdc supply has been turned OFF (typically removing your ignition key).
The Dash Cam will also enter standby mode if no physical movement is detected for 5
minutes, this is designed to allow use of a permanent 12Vdc supply, i.e hard-wire kit.
Should physical movement of the vehicle be detected, the Dash Cam will power on and
start recording a 2 minute protected video. If no further physical movement is detected then
the Dash Cam will return to standby mode, if physical movement is detected subsequently,
then the camera will continue to record normally, i.e. driving once more.
Options: On and Off
Default Setting: Off
8.
Rotate Display
Rotate the display 180°, particularly useful should the Dash Cam be mounted on the
dashboard, the Dash Cam control button functions do not rotate.
9.
Time & Date Stamp
Turn On / Off the time and date stamp shown on recorded files.
Options: Off and On
Default Setting: On
10. Speed Stamp
Turn On / Off the Speed Stamp shown on recorded files.
Options: On and Off
Default Setting: On
23
VIDEO MODE (CONTD.)
Continued from previous page.
Video Menu
GPS Location Stamp
Model Number Stamp
G Sensor
Number Plate
MENU Back
OK
Enter
13. GPS Location Stamp
Turn On / Off both the GPS co-ordinates and speed stamp that are shown on recorded files.
When a recording is viewed using the supplied NEXTBASE Replay playback software both the
GPS co-ordinates and speed information remains available.
Options: On and Off
Default Setting: On
12. Model Number Stamp
Turn On / Off the Model Number stamp shown in the bottom left corner of recorded files.
Options: On and Off
Default Setting: On
13. G Sensor
Turn Off or adjust the sensitivity of the built in G Sensor. The G Sensor detects forces which
will automatically protect the current recording in event of a collision.
Note:
- This does not affect Parking mode sensitivity.
Options: High, Medium, Low and Off
Default Setting: Medium
Note:
- Within the Setup Menu which is accessed by pressing the MENU button twice, there is
a ‘Default Settings’ option to allow you to reset the Dash Cam to the factory defaults,
if required.
24
PHOTO MODE
Press the MODE button to select Photo mode.
The key below explains the information displayed on the screen when your Dash Cam is in Photo
mode.
1
2
16:04:37 14/10/2015
6
1.
2.
3.
4.
5.
6.
5
4
3
Mode: indicates the Dash Cam is in Photo mode.
Exposure: displays current exposure level setting.
Date: current date.
Time: current time.
Memory Card: indicates whether a memory card is present.
Battery: indicates whether Dash Cam is running on battery or external power.
See the next page for photo menu settings.
25
PHOTO MODE (CONTD.)
Photo Menu
The Photo Menu is accessed by pressing the MENU button whilst in photo mode.
Photo Menu
Exposure
Time & Date Stamp
MENU Back
OK
Enter
The default settings have been carefully selected to allow you to use the Dash Cam without the
need to change any settings. However, should you wish to change a setting then please see below.
Use the up and down buttons to highlight the function that you'd like to change and press the OK
button to enter the settings sub-menu.
Once in the sub-menu, use the up and down buttons to highlight the required setting and then press
OK to confirm your selection and return to the Photo Menu.
Press the MENU button twice to return to photo mode.
1.
Exposure
Adjust exposure level for different light conditions.
Options: +2, +1, 0, -1 and -2
Default Setting: 0
2.
Time & Date Stamp
Turn On / Off the time and date stamp shown on images.
Options: On and Off
Default Setting: On
Note:
- Within the Setup Menu which is accessed by pressing the MENU button twice, there is
a ‘Default Settings’ option to allow you to reset the Dash Cam to the factory defaults,
if required.
26
PLAYBACK MODE
Press the MODE button to select Playback mode, the Dash Cam will display the last recorded file.
Dependent on the type of file, the on-screen information and playback functions differ.
Video Files:
2
3
2015_1209_184030_003A.MOV
1
9
1:39
4
HH:MM:SS
DD/MM/YYYY
5
6
8
7
1.
2.
3.
4.
5.
6.
7.
8.
9.
Mode: indicates the Dash Cam is in Playback mode.
File type: indicates whether a video or photo file is being viewed.
File number: displays current file number.
Elapsed time: Displays the elapsed time for the video being watched.
Time: displays the start time that the current file was recorded.
Date: displays date that the current file was recorded.
Playback controls: use the Dash Cam buttons as described below.
Battery: indicates whether Dash Cam is running on battery or external power.
Protected file: indicates that the video file is protected.
Playback Controls:
OK : / II
MODE :
: PREV
:
: NEXT
:
Press the OK button to play / pause playback.
Press the MODE button to stop playback.
Use the UP button to select the previous file, this is only available once playback
has been stopped.
During playback press the UP button to rewind, press the DOWN button to cancel.
Use the DOWN button to select the next file, this is only available once playback
has been stopped.
During playback press the DOWN button to fast forward, press the UP button to
cancel.
27
PLAYBACK MODE
Photo Files:
2
3
1
2015_1209_184030_003.JPG
9
HH:MM:SS
DD/MM/YYYY
8
7
1.
2.
3.
4.
5.
6.
7.
8.
9.
6
Mode: indicates the Dash Cam is in Playback mode.
File type: indicates whether a video or photo file is being viewed.
File number: displays current file number.
Time: displays the time that the current image was taken.
Date: displays the date that the current image was taken.
Next: press the down button to move to previous file.
Previous: press the up button to move to previous file.
Battery: indicates whether Dash Cam is running on battery or external power.
Protected file: indicates that the video file is protected.
Within Playback mode there are options available to Delete and Protect files, press the MENU
button to access the Playback Menu.
See following pages for details.
28
PLAYBACK MODE (CONTD.)
Deleting files:
Highlight the Delete Files option and press the OK button.
Playback Menu
Delete Files
Protect Files
MENU Back
OK
Enter
This will then give you two options:
Delete File
Delete ALL Files
Delete Files
Delete Files
Delete File
Delete File
Delete ALL Files
Delete ALL Files
MENU Back
OK
Enter
MENU Back
Once selected, follow the on screen
instructions to delete the current file.
OK
Enter
Once selected, follow the on screen
instructions to delete all files.
Note:
- Protected files cannot be deleted.
29
PLAYBACK MODE (CONTD.)
Protecting files:
Highlight the Protect Files option and press the OK button.
Playback Menu
Delete Files
Protect Files
MENU Back
OK
Enter
This will then give you two options:
Protect File
Unprotect File
Protect Files
Protect Files
Protect File
Protect File
Unprotect File
Unprotect File
MENU Back
OK
Enter
MENU Back
Once selected, follow the on screen
instructions to Protect the current file
OK
Enter
Once selected, follow the on screen
instructions to Unprotect the current file.
Note:
- The ‘Protect’ button can also be used to Protect files when in Playback Mode.
30
SETUP MENU
Setup Menu
The Setup Menu is accessed by pressing the MENU button twice.
Setup Menu
Wi-Fi
Format SD Card
Time & Date
Time Zone / DST
MENU Back
OK
Enter
The default settings have been carefully selected to allow you to use the Dash Cam without the
need to change any settings. However, should you wish to change a setting then please see below.
Use the up and down buttons to highlight the function that you'd like to change and press the OK
button to enter the settings sub-menu.
Once in the sub-menu, use the up and down buttons to highlight the required setting and then press
OK to confirm your selection and return to the Photo Menu.
Press the MENU button twice to return to video mode.
1.
Wi-Fi
The Wi-Fi function allows you to use your smartphone or tablet device to view recordings
directly from the Dash Cam.
2.
Format SD Card
Format the inserted memory card, this will delete all content.
Note:
- For stable performance, it is recommended that you format the memory card every
2-3 weeks.
Of course, you should only do this AFTER you've downloaded any files from the card that
you may want to keep.
3.
Time & Date
Adjust the time / date as required using the OK button to toggle through the fields and use
the up & down buttons to set variables. Press MENU to exit and return to the Setup Menu.
4.
Time Zone / DST
The Time and Date are automatically set based on the Country selected from within the
First Time Use menu.
The Time Zone / DST options are used should you want to manually select a Time Zone
that falls outside of the available Country options.
31
SETUP MENU (CONTD.)
Continued from previous page.
Setup Menu
Language
Country
Speed Units
Screen Display
MENU Back
5.
OK
Enter
Language
Select preferred language.
Options: English, Danish, Dutch, Finnish, French, German, Italian, Norwegian
Spanish and Swedish
Default Setting: English
6.
Country
Select your current Country, this will then automatically adjust the Time Zone / DST setting
to your Time Zone, i.e. if France is selected the Time Zone will become GMT +1.
If your required Country is not available, select ‘Other’. This will take you to the
‘Time Zone / DST’ menu, from there you can manually select your Time Zone.
Options: United Kingdom, Belgium, Denmark, Finland, France, Germany, Italy, Netherlands,
Norway, Poland, Spain, Sweden and Other
Default Setting: United Kingdom
7.
Speed Units
Select whether to record and display speed in KMH or MPH.
Options: KMH and MPH
Default Setting: MPH
8.
Speed Display
When turned on, the screen will display current speed after 30 seconds of button inactivity,
press any button to return to normal viewing, this function is only available when a GPS
connection is present.
Options: On and Off
Default Setting: Off
22
SETUP MENU (CONTD.)
Continued from previous page.
Setup Menu
Screen Saver
Screen Dimming
Device Sounds
Announcements
MENU Back
9.
OK
Enter
Screen Saver
Turn on the Screen Saver function to shut down the screen after 30 seconds of button
inactivity, press any button to re-activate the display.
Note:
- If the Speed Display function has been turned on, then Screen Saver will not be
available.
Options: Off, 10 Seconds, 30 Seconds and 2 Minutes
Default Setting: Off
10. Screen Dimming
Turn Off / On the automatic screen brightness, when driving in low level light conditions.
Options: On and Off
Default Setting: On
11. Device Sounds
Turn Off / On the beep sound which is heard when a button is pressed and also mute
the startup and shutdown chimes.
Options: On and Off
Default Setting: On
12. Announcements
Turn Off / On the spoken Announcements.
The spoken announcements provide an audible confirmation of the button that has been
pressed and it’s function. The announcements also serve as positive confirmation after a
file has been protected due to G-Sensor activation during recording.
Options: On and Off
Default Setting: Off
Note:
- Announcements are currently only available in English.
- Turning on Announcements will turn off the Device Sounds.
33
SETUP MENU (CONTD.)
Continued from previous page.
Setup Menu
Auto Power Off
System Info
Default Settings
MENU Back
OK
Enter
13. Auto Power Off
Adjust the timing of the Auto Power Off function, this can be used to continue recording in
event of loss of power within the vehicle.
Options: 10 Seconds, 1 Minute and 2 Minutes
Default Setting: 10 Seconds
14. System Info
Version:
The installed software version of your Dash Cam is displayed here.
Wi-Fi Info:
View the SSID (network name) and Password of your Dash Cam.
15. Default Settings
Reset the Dash Cam to the default settings.
34
PC CONNECTION
Use the supplied USB cable to connect the Dash Cam directly to your PC via the
do NOT connect the USB cable to the Powered Mount.
socket,
Once connected the Dash Cam will turn on with two options available, as described below.
- Mass Storage
- Power On
- Update
Use the UP and DOWN buttons to select required function and press OK to confirm selection.
Mass Storage (Windows)
When this option is selected, the Dash Cam will function as a card reader for your PC. An extra
drive will appear, e.g. Removable Disk (D:) and you will be able to view / manage the stored files upon
the MicroSD card within the Dash Cam.
Note:
- The Dash Cam is a ‘read-only’ device, therefore uploading files to the SD card when
in Mass Storage mode is not possible.
Turn off the camera before disconnecting from your computer.
Mass Storage (Mac)
When this option is selected, the Dash Cam will function as a card reader for your MAC.
The Dash Cam will be seen as an external disk upon your MAC and you will be able to view and/or
manage stored files.
Note:
- The Dash Cam is a ‘read-only’ device, therefore uploading files to the SD card when
in Mass Storage mode is not possible.
Turn off the camera before disconnecting from your computer.
Power On (Windows & Mac)
When this option is selected, the Dash Cam will power on with all functions available. This
includes charging of the internal battery, a full charge will take approximately 2 hours.
Note:
- ALWAYS turn Off the Dash Cam before disconnecting from your computer.
Update (Windows and Mac)
When this option is selected, it is for use with the NEXTBASE Replay 3 Playback software in order to
update the Firmware within the Dash Cam to the latest version.
Please see details within the NEXTBASE Replay 3 Playback software for more information.
35
VIDEO & AUDIO OUTPUT
The Dash Cam has two methods for video and audio output:
High Definition Output
When you connect a compatible High Definition cable (sold separately) between the Dash Cam and
your television, the Dash Cam screen will blank. This is normal, as all output is now visible upon
your television.
All functions of the Dash Cam are available whilst using the High Definition output.
Please contact your local NEXTBASE dealer for accessory purchases.
Note:
- An external power supply may be required when viewing recordings via the AV or HD output of the
Dash Cam, e.g. using the supplied USB cable with a 5Vdc/USB adaptor, of the type typically
supplied with mobile phones.
- ENSURE that any external power sources are of the correct 5Vdc output, otherwise damage will
be caused that is not covered under the manufacturers warranty.
36
TROUBLE SHOOTING
PROBLEM
SOLUTION
The sucker will not stay in
place upon my windscreen.
Ensure that the protective cover (plastic film) has been removed
from the suction pad.
Moisten the sucker slightly before affixing upon the windscreen.
Ensure that the locking lever is fully open when the sucker is
pushed on to the windscreen and then close the lever.
Make sure that the glass is smooth and clean.
Do not stick to glass that has any non-smooth effect or paint
whatsoever. Affix to the glass firmly and then close the locking
lever fully.
I cannot insert the MicroSD
card.
MicroSD card are very small and require delicate use. Align the
card with the diagram shown upon the Dash Cam and insert the
card until you feel a slight spring resistance. You now need to push
the card, using your finger nail, until you hear and feel a small
latch. Release pressure and the card will stay retained within the
device. Use the edge of a small coin if you have difficulty.
I cannot remove the MicroSD
card.
With the card previously installed, you now need to push the card
further inwards slightly, using your finger nail, until you hear and
feel a small latch.
Use the edge of a small coin if you have difficulty.
Release pressure and the card will spring out sufficiently for you to
take hold of it.
I can only record a few
minutes of video on my
MicroSD card.
Change the recording size (Video Length function) to a smaller
size. Increase the size of the MicroSD card. Max 64GB.
I cannot save files to the
memory card when the
Dash Cam is connected to
my computer under
Mass Storage mode.
Correct, the Dash Cam is a 'read-only' device.
It is not recommenced to save files from other sources to the same
memory that you will use for recording within the Dash Cam, as
these may have a negative effect on the performance of the
Dash Cam.
No power to my Dash Cam,
but it works upon my PC.
The cigarette power cable is not working. Inspect the fuse in the
Car Power plug. Replacement fuse = 2A 20mm type. If the fuse is
found to be blown, inspect the power cable for damage which may
have caused the fuse blow.
My Dash Cam shuts down by
itself after a while.
Either the battery has gone flat, there is no power to the Dash Cam
and the Auto Power Off period has been triggered or Parking Mode
has been turned on and no vehicle movement has been detected
for 5 minutes.
The screen blanks after a few The screen saver is set to ON. Change settings to OFF if required.
Default setting is off.
minutes upon my
Dash Cam.
The battery will not charge.
Ensure the Dash Cam is connected to a reliable power source an
that the supplied Car Power Cable is being used, with the Power
LED lit.
37
TROUBLE SHOOTING (CONTD.)
PROBLEM
SOLUTION
The battery only last 30
seconds.
The battery will only receive charge when the Dash Cam is
connected to power, please reconnect the car adaptor or domestic
USB charger and leave the Dash Cam to charge.
Charging takes approximately 90 minutes and a full charge is
indicated when the BLUE (charging) LED goes out.
The battery only lasts 30
minutes.
This is normal, the battery design allows the 'Auto Power Off'
feature to function in event of power loss within the vehicle.
It is not intended as an alternative power source to replace the
supplied car adaptor.
The Dash Cam can not lock
onto satellite.
After power on and with the device mounted with clear view of the
sky it can take up to 10 minutes to find the three satellites required
to achieve a stable signal. Reception can also be affected by
atmospheric conditions and the proximity of buildings / trees
obscuring the sky.
I get the message “SD Card
Error. Please format SD card”
on screen.
The SD card has been formatted in another device and the Cluster
Size is not compatible or the SD card is formatted in ExFAT /
NTSC. There may also be an error on the card. Use the Setup
option to re-format the SD card from within the Dash Cam.
I get the message “Card Full”
on screen.
The SD card has become full as there may be too many
protected files which will not be deleted to allow for further
recording to take place. Delete unnecessary files or perform a
full FORMAT upon the SD card from within the Dash Cam
Setup Menu.
The SD card in my Dash Cam Use a good quality branded SD card between 8GB and 64GB
(Class 10 or UHS type 1) and format the card from within the
cannot be read.
Setup Menu.
I can't delete files on my SD
card within the Dash Cam.
Check to see if these files are 'protected', if so please follow
instructions to 'un-protect'.
Mass Storage function does
not work.
The Mass storage function will work on both Windows and Mac.
Restart the PC, as this may be required for the necessary driver to
be loaded correctly. Disconnect and reconnect the Dash Cam.
Contact NEXTBASE for the required driver.
Video files cannot be played.
The video files from the iN CAR CAM are in .MOV format and may
not be compatible with your PC if suitable playback software is not
installed.
Video Image is blurred.
Remove the protective lens cover, clean the lens, adjust the
polarising filter correctly, clean the windscreen!
38
TROUBLE SHOOTING (CONTD.)
PROBLEM
Video file playback is jumpy.
SOLUTION
Remove the SD card and reformat to remove non-contiguous files.
For best recording use a quality branded class 10 type (48MB/s)
or UHS type 1 micro SD card of 8 to 32GB recommended size.
PC may not be sufficient for the playback task, try a different PC.
Copy the recorded video files onto the PC / Mac for playback
directly rather than use the Dash Cam as a card reader, as the
USB system on your PC may be too slow for HD video playback.
Reduce the resolution of the recording within the Dash Cam and
record some new files to test if this is the problem.
The sound is not synchronised The Codecs upon your PC may not be compatible or the latest
standard.
with video during playback.
Download the latest Codecs from: www.nextbase.co.uk
Video has no sound.
Ensure that “Record Audio” setting is turned ON within the Video
Menu of the Dash Cam.
Video playback is really quick Turn off the Time Lapse Recording, form within the Video Menu.
on my PC, not consistent with
the drive that was recorded.
Photograph is blurred.
Hold the camera still whilst taking the photo. Please be aware the
photo is taken around 1 second after the shutter noise is heard.
I have turned on 'Parking
Mode' and now can't stop the
recording.
The Dash Cam will start a recording whenever motion is detected.
To turn off Parking Mode firstly shutdown the
Dash Cam and remove the SD card, this will avoid recording being
activated accidentally. Switch the Dash Cam Oo and within the
Setup Menu, turn off the 'Parking Mode'.
When I get in to my car, the
Dash Cam is already
recording and the file is
protected.
This is normal. Parking Mode has been switched on and the
Dash Cam has sensed vibration and has started to record
correctly.
Parking mode can be turned off within the Video menu if required.
When I press the MENU
button nothing happens.
This is normal during recording. Stop the recording before pressing
the MENU button.
If recording re-starts before you can press MENU, then see the
Parking Mode section above.
The time on my Dash Cam is
wrong and when I adjust the
time manually, it keeps
changing.
The Dash Cam sets the time based upon the country which has
been selected and also whether Daylight Savings time is currently
in force. Please verify the Country setting within the menu is
correct. The Time Zone can be set manually, if the Dash Cam is to
be used outside the listed countries in the Setup Menu.
Downloading files from
www.nextbase.co.uk
using Google Chrome results
in a Malicious Software
message.
This is not a cause for concern, simply go to the settings within
Google Chrome and turn off the malicious software protection
temporarily to download and install the playback software.
Reinstate previous Google Chrome settings thereafter.
39
TROUBLE SHOOTING (CONTD.)
PROBLEM
SOLUTION
My Mobile Device will not
connect to my camera.
Please ensure that you have turned the Dash Cam Wi-Fi Mode on
by either using the Wi-Fi button or through the Settings Menu.
When Wi-Fi Mode is turned on the screen of the Dash Cam will
display the Network Name and Password.
This password is case sensitive.
The NEXTBASE Cam Viewer
app will not open.
Please uninstall the NEXTBASE Cam Viewer app and re-download
again from your devices App Store.
When I open the NEXTBASE
Cam Viewer App I get a
message saying
'Please Check Device'.
Ensure that the Dash Cam is in Wi-Fi Mode and that your mobile
device has connected to the Dash Cam Wi-Fi connection.
When I try to play back a file
from my Dash Cam I get a
message saying 'Buffering'
but the video does not load.
Please restart your mobile device and reconnect to the Dash Cam
Wi-Fi connection.
Then re-open the Cam Viewer App.
Unresolved issues.
Reset the Dash Cam to the Default Settings within the Setup Menu
and try again.
Should the problem persist call the helpline (02920) 866429 or
email: [email protected]
40
NOTES
www.nextbase.co.uk
NBDVR512GW-IM-ENG-R5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement