Owners Manual - Conag Equipment

Owners Manual - Conag Equipment
Owners Manual
MK4 Renovator
ORIGINAL INSTRUCTIONS
Head Office:
P.O. Box 2018
Hilton Highway, Washdyke
Timaru, New Zealand
Telephone (03) 688 2029
Facsimile (03) 688 2821
Australian Branch:
4B Silverton Close
Laverton North 3026
Melbourne, Australia
Telephone (03) 9314-9666
Facsimile (03) 9314-6810
Pt. No. 67381
Issue 0511
Mk4 Renovator
Contents
Page
Introduction
Acquisition & Warranty
Disclaimer
Description of Machine
Specification
......................................
2
......................................
2
......................................
2
Working Principle. . . . . . . . . . . . . . . . . . . . . . .
3
Dimensions & Capacities . . . . . . . . . . . . . . . .
5
SAFETY - General
Safety Symbols on Machine . . . . . . . . . . . . . .
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . .
Be Prepared for Emergencies . . . . . . . . . . . . .
Appropriate Dress . . . . . . . . . . . . . . . . . . . . . .
Transport This Machine Safely . . . . . . . . . . . .
Handle Agricultural Chemicals Safely . . . . . . .
Avoid High Pressure Fluids . . . . . . . . . . . . . . .
Safe Work Practices . . . . . . . . . . . . . . . . . . . .
Practise Safe Maintenance . . . . . . . . . . . . . . .
Hazard Points . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Decals & Safety Guards. . . . . . . . . . . .
......................................
......................................
6
7
7
8
8
9
9
9
10
11
13
14
15
SAFETY - Machine Specific
Transport
Operation
Sowing Chart
Basic Calibration Procedure
Maintenance & Care
Parts List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Gearbox Setting Lever . . . . . . . . . . . . . . . . . .
Setting Seeder Shutter Slides . . . . . . . . . . . . .
Bottom Flap Settings . . . . . . . . . . . . . . . . . . . .
Seed Calibration . . . . . . . . . . . . . . . . . . . . . . .
Hand Crank Turns for Seed Rate Calibration .
Use of Seed Rate Calculator. . . . . . . . . . . . . .
Calibration Deviations . . . . . . . . . . . . . . . . . . .
Sowing of Fine Seeds . . . . . . . . . . . . . . . . . . .
Sowing Small Seeds . . . . . . . . . . . . . . . . . . . .
Sowing Peas . . . . . . . . . . . . . . . . . . . . . . . . . .
Hectaremeter Settings. . . . . . . . . . . . . . . . . . .
Calibration Notes . . . . . . . . . . . . . . . . . . . . . . .
22
22
22
23
24
25
26
27
28
28
29
31
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Lubrication Instructions . . . . . . . . . . . . . . . . . . 33
Maintenance Schedule . . . . . . . . . . . . . . . . . . 34
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Troubleshooting/Maintenance Notes. . . . . . . . 37
Commisioning/Troubleshooting Phasing Rams 38
Calibration Chart and Handy Hints . . . . . . . . . 41
(copies of chart that may be found inside box lids)
Base Machine . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Extras . . . . . . . . . . . . . . . . . . . . . . . .
47
82
Pt. No. 67381
Issue 0511
1
Introduction
Acquisition & Warranty
On delivery of your new Duncan Renovator please check that
the machine is not damaged. In cases of shipping damage,
please ask your dealer to arrange for the appropriate claim
to be lodged immediately. Assemble any parts supplied
loose and inspect your machine with the aid of this manual to
familiarise yourself with its features. If you have any queries
ask your dealer straight away. The machine is covered by our
12 month warranty on faulty parts, subject to normal use.
Record below the serial number of your machine and keep
it in a secure place to help trace the machine and assist
us when you order parts.
Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.............................................
.............................................
Delivery Date:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dealer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.............................................
.............................................
The Owner’s Manual
Your new Duncan Renovator will give long and efficient service
if given normal care and operated properly.
This owner’s manual is provided so that you can become
thoroughly familiar with the design of the machine and to
furnish information on correct operation, adjustment and
maintenance. Only persons well acquainted with these
guidelines should be allowed to use the equipment.
A separate illustrated parts section has been provided so that
if any parts are required your dealer will be able to supply
them by reference to part numbers.
The manual is considered as part of your machine and must
remain with the machine when it is sold.
Right and left hand references in this manual are
determined by standing behind the machine and facing in
the direction of travel.
2
This Document contains the Original
Operating Instructions for this machine
and are verified by the Manufacturer.
Signed:......................................
Product Development Manager
Disclaimer
Every effort has been made to
ensure that the information in this
manual was accurate and up to
date at the time of going to press.
Clough Agriculture reserves the
right to make subsequent changes
to the machine, where necessary,
without notification.
The Company will not be
responsible for any damage or
consequential loss arising out of
misinterpretation or failure to follow
recommended procedures. Nor will
it be liable for any damage caused
by or arising out of modification or
misuse of its product.
The owner has a responsibility
to protect himself and others
by observing all safety
information and by ensuring all
operators are well acquainted
with the safety information,
trained in the correct use of
the machine and applying safe
work practices.
Description of Machine
The Duncan ‘Mk4 Renovator’ is a Coil Tine T-boot drill.
The box is mounted on a robust frame accommodating
large diameter tyres. The ground engaging components
are controlled by a hydraulic ram system, giving ample
control on ground pressure, good transport clearance
and contour following ability. Sowing depth is controlled
by adjusting the hydraulic ram as required. The quality
European type peg roller seeder system handles all
seeds from turnip and rape through to peas and maize.
The seeders are driven from the groundwheels via a
jockey wheel system and variable speed gearbox. For
transport, the drive is easily disconnected by raising the
drill to its transport height.
Working Principle
The gearbox, pegged seed rollers and seeder flaps are
set to give the desired seed rate. The coil tine and Tboot, create the seed bed. Seed flows down the flexible
tubes between seeder and tee-boot units, and drops into
the prepared seed bed.
Pt. No. 67381
Issue 0511
3
4
5
2030
Weight inc. disc openers (unladen)
2848
550
Effective Sowing Width
Box Capacity (litres per box)
WIDTH (refer specification table)
Maximum Tractor HP Rating
Small Box Capacity (litres)
178
Row Spacing
Jockey Tyre Pressure
Jockey Tyre Size
Maximum speed (km/hr)
Recommended Tyre Pressure
HEIGHT (refer specification table)
70
550
3097.5
147.5
3825
Overall Length (mm)
Tyre Size
2430
Height (Groundwheels down /mm)
1850
2145
Height (Groundwheels up /mm)
3m Std
21 Run
3070
3m Wide
16 Run
Width (over wheels /mm)
Description
Dimensions & Capacities
2220
3.5m Wide
20 Run
2360
3825
2430
2145
3570
3.5m Std
24 Run
550
3000
125
OVERALL LENGTH XXXX
(refer specification table)
180
650
3560
178
3.44 bar (50 psi)
410/350 x 6 x 4 ply
40 (tyre rating 138A8)
4 bar (58 psi)
90
650
3540
147.5
10.0/75-15.3 (18 ply AW702)
2130
3m Narrow
24 Run
650
3500
125
2490
3.5m Narrow
28 Run
Dimensions & Capacities
Pt. No. 67381
Issue 0511
!
ATTENTION
On the machine important safety information is indicated by these symbols.
These highlight general safety aspects in regard to the machine rather than specific hazards.
Do not ride or allow passengers on the machine.
Under no circumstances are passengers to be permitted
on the machine while it is in operation or being transported.
Any footboards and/or footsteps are provided solely for the
purpose of preparing the machine for use.
Keep clothing and body extremities well clear of pinch
points while the machine is operating (seeding or
calibrating). Keep well clear of moving parts at all times.
These signs typically occur wherever trapping points exist.
These include drive chains, sprockets, shafts, wheels, discs,
pivot points, etc. Guards are provided with the machine
for safety reasons (where practical without compromising
machine performance). Ensure these are always fitted
during operation.
Always exercise extreme caution in the vicinity of sharp
edges and points.
Where possible guards are provided with the machine
for safety reasons (where practical without compromising
machine performance). Ensure these are always fitted
during operation.
Footboards, footsteps, drawbars and other machine
surfaces may be slippery when wet.
Apply extra caution in wet conditions and in the early
morning when surfaces are wet.
Keep Clear. (It is dangerous to be in this area when the
machine is operating.)
6
SAFETY - General
N.B. Throughout this
manual important safety
information is indicated
by these symbols in the
margin:
A prohibition should
be observed under all
circumstances.
A warning indicates a
hazard that could cause
death or injury if the
warning is ignored.
A caution indicates a
hazard that may cause
damage to property if
the caution is ignored.
This section of the manual offers general guidelines
for the safe operation of machinery. It does not replace
local safety regulations. These guidelines were current at
the time of publication, but may be superseded by later
regulations.
Clough Agriculture has made every effort to highlight all
risks to personnel or property. Owners and operators have
a responsibility to exercise care and safe work practices at
all times in the vicinity of the machine.
Owners are advised to keep up to date on safety issues
and to communicate these to all users of the machine.
Contact the Occupational Safety and Health Service
(OSH) for further information about general safety aspects.
If you have safety concerns specifically related to this
machine, contact your dealer immediately.
Operator Safety
Read this manual carefully before operating new
equipment. Learn how to use this machine safely.
Be thoroughly familiar with the controls and the proper use
of the equipment before using it.
Take careful note of all safety instructions both in this
manual and on the machine itself. Failure to comply with
instructions could result in personal injury and/or damage
to the machine.
Replace missing or damaged safety signs on the machine
and ensure that these remain clearly visible.
It is the owner’s responsibility to ensure that anyone
who operates, adjusts, lubricates, maintains, cleans
or uses the machine in any way has had suitable
instruction and is familiar with the information in this
manual (particularly with regard to safety aspects).
Operators and other users of the machine should be
aware of potential hazards and operating limitations.
Be Prepared for Emergencies
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance,
hospital and fire department near your telephone.
Pt. No. 67381
Issue 0511
7
SAFETY - General (Continued)
Appropriate Dress
Wear close fitting clothing and avoid rings or other forms of
jewellery which could become caught in the machinery.
People with long hair must have it securely fixed and confined
close to the head.
Refer to local safety standards for protective clothing and
recommended safety equipment.
Adequate protection, such as a face mask, should be worn if
operating this machine in dry and dusty conditions.
Transport This Machine Safely
Ensure that all linkage pins and security clips are fitted correctly.
With trailing machines tow with the drawbar only, as this is the
only safe towing point on the machine.
Always check that bystanders (especially children) are well clear
(front and rear) before starting and moving the tractor and the
machine.
Plan safe routes of travel, and be aware of power lines and
other roadside hazards. Take particular care when towing
implements on hillsides.
Do not ride or allow passengers on the machine.
This machine is not designed to carry passengers, and no riders
are permitted.
Road transport
On public roads,
• A speed of 40km/h must not be exceeded.
• Do not operate during the hours of darkness unless standard
lights are fitted and clearly visible. (This also applies when
visibility is limited, e.g., in foggy conditions.)
See the guidelines in the Vehicle Dimensions and Mass Rule,
issued by the Land & Transport Safety Authority.
Avoid tip-overs
Avoid holes, ditches and obstructions which may cause the
machine to tip over, especially on hillsides. Never drive near the
edge of a gully or steep embankment - it might cave in. Slow
down for hillsides, rough ground and sharp turns.
8
SAFETY - General (Continued)
Handle Agricultural Chemicals Safely
All farm chemicals should be stored, used, handled and
disposed of safely and in accordance with the supplier’s/
manufacturer’s recommendations.
Read the product label before using, noting any warnings
or special cautions, including any protective clothing or
equipment that may be required, ie. respirator.
Do not eat or smoke while handling sprays, fertilisers, coated
seeds, etc. Afterwards, always wash your hands and face
before you eat, drink, smoke, or use the toilet.
Store sprays, fertilisers, coated seeds, etc. out of reach of
children and pets, and away from food and animal feeds.
Any symptoms of illness during or after using chemicals
should be treated according to the supplier’s/manufacturer’s
recommendations. If severe, call a physician or get the
patient to hospital immediately. Keep the container and/or
label for reference.
Avoid High Pressure Fluids
Avoid any contact with fluids leaking under pressure, because
the fluids can penetrate the skin surface.
Any fluid which penetrates the skin, will need to be removed
immediately by a medical expert. Seek specialist advice on
this type of injury.
Relieve the pressure before disconnecting any hydraulic or
other lines. Make all repairs and tighten all fittings before
re-connection to pressurised fluid.
Keep your hands and body away from any pinholes or high
pressure jets. Search for leaks with a piece of cardboard
instead of using your hand directly.
Safe Work Practices
All farm machinery is potentially dangerous and should be
treated with caution and respect.
Before starting the machine, ensure that all controls are placed
in neutral and that bystanders are well clear. Check that the
guards have been securely fitted and that any adjustments
have been made correctly.
Where possible, disconnect or isolate the drive mechanism to
the implement. Lower the machine onto the ground when not
in use.
Do not operate this equipment when severe weather
conditions appear imminent.
Pt. No. 67381
Issue 0511
9
SAFETY - General (Continued)
Practice Safe Maintenance
Keep the machine in safe working condition. Routine maintenance
and regular servicing will help reduce risks and prolong the life of the
machine.
General Maintenance
Accidents occur most frequently during servicing and repair. The
following general rules must be followed when maintaining or working
with machinery:
• All operating and maintenance manuals must be
read before and referred to while using or servicing any
piece ofequipment.
• Turn off all machinery power sources and isolate the
machine before making adjustments, doing lubrication,
repairs or any other maintenance on the machine.
• Ensure that the machine hydraulics are disconnected from
the power source.
• Wear gloves when handling components with cutting
edges, such as any ground cutting components.
• Beware of hazards created by springs under tension
or compression when dismantling or maintaining the
machine.
• It is recommended that you clean the machine with a water
blaster or similar apparatus before commencing
maintenance.
Make Sure the Machine is Well Supported
When machinery is fitted with hydraulics, do not rely on the
hydraulics to support the machine. During maintenance or while
making adjustments under the machine, always lock the hydraulics
and support the machine securely. Place blocks or other stable
supports under elevated parts before working on these.
Electrical Maintenance
Disconnect the electrical supply from the tractor before doing any
electrical maintenance.
Welding
With electronic equipment in modern tractors it is advisable to disconnect
the machine from the tractor, or at least disconnect the alternator and
battery before attempting any welding.
Use Only Genuine Spare Parts
Unauthorised modifications or non-genuine spare parts may be
hazardous and impair the safe operation and working life of the machine.
Excess lubricants must be disposed of safely so as not to become a
hazard.
10
SAFETY - Machine Specific
This section of the manual gives specific guidelines for
the safe operation of the Renovator.
These guidelines were current at the time of publication, but
may be superseded by later circumstances. They do not
necessarily cover every possible hazard and must be read in
conjunction with the SAFETY - General section (Page 7 to 10).
Hazard Points on the Renovator
The lists below are not all-inclusive and serve only to highlight
the more obvious areas of risk.
The decals attached to the machine are a general reminder
that there are hazardous areas on the machine, rather than
specifically highlighting all possible hazards.
For decal locations on machine, refer Page 13.
No Ride
Passengers are not permitted anywhere on the machine.
Pinch Points/Moving Parts
Hazardous areas include:
• Drive chains.
• Sprockets between the drive wheel, the transfer shaft and
the gearbox (RH side).
• Sprockets between the gearbox and the box shafts
(RH side).
• Agitator drive units (LH side).
• Agitator shaft inside the boxes.
• Seeder units, box shaft and shaft connectors.
• Wheel legs and main frame assemblies
• Between discs and other sub-assembly parts (where fitted).
• Finger tine assemblies (where fitted).
Slippery When Wet
Hazardous areas include:
• Footboards and footstep.
• All smooth surfaces on the frame structure.
Keep Clear
Hazardous areas include:
• Between the tractor and Renovator.
• Immediately adjacent to the Renovator side.
Pt. No. 67381
Issue 0511
11
SAFETY - Machine Specific
(Continued)
Hazard Points on the Renovator
(Continued)
Pedestal Chain Guards
To prevent hands, etc. getting caught in drive chains, guards
are provided to cover sprockets, chain and chain tensioners
mounted about the drive pedestal (RHS). These guards must
be fitted while using the machine.
Warning: Access to pinch points is still possible from
underneath the guard.
For guard locations on machine, refer Page 13.
Calibrating
Be particularly careful when calibrating the seeding rate. At
this time, the calibration trays have been removed and are no
longer covering the rotating seeder units. See Pinch Points/
Moving Parts (Page 11) for hazardous areas.
Transport
The two wheels located at the sides of the machine are for the
purpose of controlling sowing depth. These are also used to
support the machine weight during transport (while linked to
the tractor).
Important - Refer to safety cautions in the Transport section,
page 14 of the manual. Ensure that all linkage pins and
security clips are fitted correctly.
Maintenance
Refer Page 32 for reference to the Maintenance and Care
section of the manual.
Lubrication
Refer Page 33 for reference to the Maintenance and Care
section of the manual.
12
SAFETY - Machine Specific
(Continued)
1
2
5
3
On end of
footboard
8
1
3
7
6
8
6
4
Item Decal/Guard
Pt. No. Qty
1
‘No Ride’
43900
3
2
‘Pinch Point/Moving Parts’
43901
5
3
‘Slippery When Wet’
43902
2
4
‘Keep Clear’
43904
2
5
Arrows (Inside Box Lid)
43905
4
6
Pedestal Drive Guard (Dual box machine)
25995
1
6
Pedestal Drive Guard (Single box machine)
25996
1
7
Jockey Drive Swing Guard
25745
1
8
‘40 km/hr’
43912
2
Table 2
Pt. No. 67381
Issue 0511
13
Fig 1
Transport
1
Raise the drill into the transport position and hold at the full
extent of the rams for a few seconds to allow cylinders to
rephase/equalise.
2
Important - To avoid machine damage due to drill
lowering during transport, always close the hydraulic valve
on the drawbar. Move the handle to a position at
900 to the hydraulic line as shown in Fig 1. This
applies to the drawbar and disc opener hydraulic
valves where fitted.
Fig 2
3
Locate jack stand in transport position, if fitted.
Refer Fig 2.
4
Ensure lighting and oversize warning
requirements meet recommendations published by
the local Land Transport Authority or equivalent.
Maximum towing speed 40 km/hr.
For countries other than New Zealand
greater speed restrictions may apply, please
refer to your local transport authority.
5
Ensure towing vehicle requirements are
adequate for the towed vehicle e.g. mass, brakes. Refer to
recommendations published by the local Land Transport
Authority or equivalent.
Fig 3
Braking when towing can cause the load to jackknife. Use
extra care when towing in adverse conditions such as mud,
inclines and sharp bends.
Lower towing speeds are recommmended on farm roads/
tracks and where one wheel is on or over a road verge.
6
Attach safety chains to tractor. Refer Fig 3.
Safety chains must be crossed over underneath the
coupling and attached to the towing vehicle. The
attachment points must be as close as practical to the
towing coupling and one each side.The towbar on the
towing vehicle must be rated for the towed mass. Do not
remove or replace the safety chains provided with any
other than those specified in the parts manual.
Note: The safety chains are provided with sufficient
length to cater for all towing vehicles. Safety chains must
be shortened by cutting off excess length so that if the
coupling fails the drawbar will not hit the ground.
7
If the machine is fitted with row markers or other vertical
extensions, check clearance under power lines en route.
8
Important - For greater disc opener ground clearance,
adjust the ram or turnbuckle on the disc opener unit so
they are at maximum height, and/or extend the drawbar
ram or turnbuckle to level the machine chassis.
14
Operation
General Operation Guidelines
1
Use a sufficiently powerful tractor which is heavy enough
to tow the drill safely.
2
Operate the drill at a speed of 6-12 km/hr (4-8 mph).
In stony and uneven ground conditions a lower speed is
more appropriate
3
Check that the drill is level during calibration and while seeding.
4
Check tyre pressure before seeding. Refer page 5.
5
Double check seed rates before seeding.
6
Raise the drill out of the ground when making any turns.
7
Raise the drill out of the ground before backing up.
8
After prolonged storage, check to see that all drive
mechanisms and hydraulic equipment are functioning
correctly. Check that the seed tubes are not perished or
blocked.
Sowing Speed
Typical travel speeds when sowing range from 6-12 km/hr
in good conditions. In stoney and uneven ground conditions
a lower speed is recommended to minimise rapid part
deterioration. Sowing too fast can result in:
1 Poor contour following and uneven sowing depth.
2 Impact damage to:
a Ground engaging components.
b Bearings, housings & axles.
c Fasteners & structural components.
3 More extreme conditions will result in greater vibration
and uneven seed flow at low seeding rates.
Sowing Depth Control
The sowing depth is dependent on:
1 The wheel height in relation to the chassis
2 Tyre pressure
3 Ground condition i.e. hard or soft
1
The wheel height in relation to the chassis is controlled using
the threaded depth adjustment collar (1) on the non-drive
wheel leg ram. The rams are phasing and only require depth
stops under the master cylinder.
Caution: Do not overextend the thread depth adjustment
collar. Additional collars may be required.
Fig 4
Pt. No. 67381
Issue 0511
15
Level Drill
Use the drawbar turnbuckle or ram to tilt the drill so it is
sitting level. An adjustment may be required after a short
period of use because the paint wears off the discs and
the discs sharpen which in turn improves the penetration
abilities.
Ensure that the front and rear rows are at an even depth.
Transport Position
When in the transport position the hydraulic cylinders are
fully extended. In this position the cylinders fully equalise
by allowing oil to bypass the master cylinder piston. It is
recommended to raise the drill into the transport position
when turning at headlands or regularly to counteract the
effects of oil leakage past the piston and ensure cylinder
rods are equally extended and minimise variations in
sowing depth.
Coulter Penetration Depth
To create the ideal seed bed the disc opener coulter
should cut approximately 20mm below the inverted
tee point. In hard and dry conditions this may not be
achievable, and better machine/sowing performance may
be achieved without using the disc openers. An indication
of this will be the machine bouncing which will result in
uneven sowing depth.
Coulters will give better penetration ability as they sharpen
with use.
16
17
18
MK 4 Renovator Seed Drill Sowing Chart
Table 3
Hi/Low
Position
180
Seed Rate (kg/ha)
Metering
Wheel*
PRODUCT
Bottom Flap*
Shutter
Slide*
High & Low Ratio - Wide Row Spacing 180
16 Run 3m and 20 Run 3.5m
Type
Agitator Shaft
Gearbox Setting Position
15
20
30
40
50
60
100
Connected
70
80
90
Wheat
H
3/4
3
N
84
105 125 148 170 192
Connected
Oats
H
Full
3
N
81
101 120 141 161 180
Connected
Barley
H
Full
3
N
97
119 144 168 194 218
Connected
Ryecorn
H
3/4
3
N
98
121 146 170 197 221
Connected
White Peas
H
3/4
3
N
92
133 175 202 250 294 325 374
Green Peas
H
3/4
3
N
64
96
128 157 189 224 259 292
Connected
Peren. Grass
H
Full
3
N
5.3
11
22
34
44
55
Connected
Annual Grass
H
Full
3
N
6.6
13
26
38
50
63
Pasture Mix*
H
Full
3
N
11
22
34
44
55
66
Connected
Lucerne
H
3/4
1
F
7.4
11
15
18
21
Disconnected
Turnip
L
3/4
1
F
1.5
2.6
3.8
4.9
Disconnected
Kale
L
3/4
1
F
1.4
2.6
3.9
4.9
Disconnected
Swedes
L
3/4
1
F
Rape
L
3/4
1
F
White Clover
L
3/4
1
F
Red Clover
L
3/4
1
F
Super Phosphate
H
Full
3
N
DAP Granules
H
Full
3
N
Super Phosphate
L
Full
3
N
DAP Granules
L
Full
3
N
0.8
0.8
0.7
66
Disconnected
Connected
1.3
Disconnected
1.3
2.5
3.6
4.8
Disconnected
1.3
2.5
3.7
4.6
Disconnected
1.6
2.9
4.1
5.5
8.0
Disconnected
75
115 152 193 235 282 325 374
Connected
143 175 211 247 284 314
Connected
58
108 125 150
Connected
95
Connected
44
Gear Ratio*: H, High = 21T on Transfer Shaft,
13T on Gearbox Input Shaft.
L, Low = 13T on Transfer Shaft,
21T on Gearbox Input Shaft.
Shutter Slide*: For Grain, changing the Shutter Slide from 3/4 to Full gives
10% to 15% more flow.
Pasture Mix*: Test Mixture = 72% Perennial Grass, 8% White Clover,
8% Cocksfoot, 8% Concord, 4% Red Clover
Notes
1.Where a small seeds box is used, multiply
the above seed rates by 0.80 to account for
the different gearing ratio.
6.7
74
90
109 120
Bottom Flap*: The values shown were the optimum test settings,
decreasing the gap may cause seed damage, too large a gap will give
intermittent flow rates. (Flaps are spring loaded to cope with small
variations in seed/granule size).
Metering Wheel*: N = Normal Metering Wheel (Both)
F = Small Metering Wheel
TSW*:
TSW(gm) x Desired Plants/m2 = Sowing Rate (Kg/Ha)
Germination %
3. To sow at rates under 30kg/Ha we
recommend using the Low Ratio.
2.Seed rates shown are approximate only
for the respective gearbox setting. It is
recommended that the calibration procedure
is always used. Refer to
page 16.
Pt. No. 67381
Issue 0511
19
MK4 Renovator Seed Drill Sowing Chart
Table 4
Hi/Low
Position
147.5
Seed Rate (kg/ha)
Metering
Wheel*
PRODUCT
Bottom Flap*
Shutter
Slide*
High & Low Ratio - Standard Row Spacing 147.5
21 Run 3m and 24 Run 3.5m
Type
Agitator Shaft
Gearbox Setting Position
15
20
30
40
50
60
70
80
90
100
Connected
Wheat
H
3/4
3
N
102 128 152 180 208 234
Connected
Oats
H
Full
3
N
99
123 146 172 197 220
Connected
Barley
H
Full
3
N
118 145 176 205 237 266
Connected
Ryecorn
H
3/4
3
N
119 148 178 207 241 270
Connected
White Peas
H
3/4
3
N
112 162 213 246 305 359 397 457
Green Peas
H
3/4
3
N
78
117 156 192 231 273 316 356
Connected
Peren. Grass
H
Full
3
N
6.5
14
27
41
54
67
Connected
Annual Grass
H
Full
3
N
8.1
16
32
46
61
77
Pasture Mix*
H
Full
3
N
14
27
41
54
67
81
Connected
Lucerne
H
3/4
1
F
9.0
14
18
22
26
Disconnected
Turnip
L
3/4
1
F
1.8
3.2
4.6
6.0
Disconnected
Kale
L
3/4
1
F
1.7
3.2
4.7
6.0
Disconnected
Swedes
L
3/4
1
F
Rape
L
3/4
1
F
White Clover
L
3/4
1
F
Red Clover
L
3/4
1
F
Super Phosphate
H
Full
3
N
DAP Granules
H
Full
3
N
Super Phosphate
L
Full
3
N
DAP Granules
L
Full
3
N
1.0
1.0
0.8
Disconnected
81
Connected
1.6
Disconnected
1.6
3.0
4.4
5.8
Disconnected
1.6
3.1
4.5
5.6
Disconnected
1.9
3.6
5.0
6.7
9.8
Disconnected
91
140 185 235 287 344 397 457
Connected
174 214 257 302 346 383
Connected
71
110 132 152 183
Connected
116 133 147
Connected
54
Gear Ratio*: H, High = 21T on Transfer Shaft,
13T on Gearbox Input Shaft.
L, Low = 13T on Transfer Shaft,
21T on Gearbox Input Shaft.
Shutter Slide*: For Grain, changing the Shutter Slide from 3/4 to Full gives
10% to 15% more flow.
Pasture Mix*: Test Mixture = 72% Perennial Grass, 8% White Clover,
8% Cocksfoot, 8% Concord, 4% Red Clover
Notes
1.Where a small seeds box is used, multiply
the above seed rates by 0.80 to account for
the different gearing ratio.
8.2
90
Bottom Flap*: The values shown were the optimum test settings,
decreasing the gap may cause seed damage, too large a gap will give
intermittent flow rates. (Flaps are spring loaded to cope with small
variations in seed/granule size).
Metering Wheel*: N = Normal Metering Wheel (Both)
F = Small Metering Wheel
TSW*:
TSW(gm) x Desired Plants/m2 = Sowing Rate (Kg/Ha)
Germination %
3. To sow at rates under 30kg/Ha we
recommend using the Low Ratio.
2.Seed rates shown are approximate only
for the respective gearbox setting. It is
recommended that the calibration procedure
is always used. Refer to
page 16.
Pt. No. 67381
Issue 0511
20
MK 4 Renovator Seed Drill Sowing Chart
Table 5
Hi/Low
Position
125
Seed Rate (kg/ha)
Metering
Wheel*
PRODUCT
Bottom Flap*
Shutter
Slide*
High & Low Ratio - Narrow Row Spacing 125
24 Run 3m and 28 Run 3.5m
Type
Agitator Shaft
Gearbox Setting Position
15
20
30
40
50
60
70
80
90
100
Connected
Wheat
H
3/4
3
N
121 152 180 213 246 277
Connected
Oats
H
Full
3
N
117 146 173 204 233 260
Connected
Barley
H
Full
3
N
140 172 208 243 281 315
Connected
Ryecorn
H
3/4
3
N
141 175 211 245 285 320
Connected
White Peas
H
3/4
3
N
133 192 252 291 361 425 470 541
Green Peas
H
3/4
3
N
92
139 185 227 274 323 374 422
Connected
Peren. Grass
H
Full
3
N
7.7
17
32
49
64
79
Connected
Annual Grass
H
Full
3
N
10
19
38
55
72
91
Pasture Mix*
H
Full
3
N
17
32
49
64
79
96
Connected
Lucerne
H
3/4
1
F
11
17
21
26
31
Disconnected
Turnip
L
3/4
1
F
2.1
3.8
5.4
7.1
Disconnected
Kale
L
3/4
1
F
2.0
3.8
5.6
7.1
Disconnected
Swedes
L
3/4
1
F
Rape
L
3/4
1
F
White Clover
L
3/4
1
F
Red Clover
L
3/4
1
F
Super Phosphate
H
Full
3
N
108 166 219 278 340 407 470 541
Connected
DAP Granules
H
Full
3
N
206 253 304 358 410 453
Connected
Super Phosphate
L
Full
3
N
84
107 130 156 180 217
Connected
DAP Granules
L
Full
3
N
137 157 174
Connected
1.2
1.2
0.9
96
Disconnected
Connected
1.9
Disconnected
1.9
3.6
5.2
6.9
Disconnected
1.9
3.7
5.3
6.6
Disconnected
2.2
4.2
5.9
7.9
64
Gear Ratio*: H, High = 21T on Transfer Shaft,
13T on Gearbox Input Shaft.
L, Low = 13T on Transfer Shaft,
21T on Gearbox Input Shaft.
Shutter Slide*: For Grain, changing the Shutter Slide from 3/4 to Full gives
10% to 15% more flow.
Pasture Mix*: Test Mixture = 72% Perennial Grass, 8% White Clover,
8% Cocksfoot, 8% Concord, 4% Red Clover
Notes
1.Where a small seeds box is used, multiply
the above seed rates by 0.80 to account for
the different gearing ratio.
10
12
Disconnected
Bottom Flap*: The values shown were the optimum test settings,
decreasing the gap may cause seed damage, too large a gap will give
intermittent flow rates. (Flaps are spring loaded to cope with small
variations in seed/granule size).
Metering Wheel*: N = Normal Metering Wheel (Both)
F = Small Metering Wheel
TSW*:
TSW(gm) x Desired Plants/m2 = Sowing Rate (Kg/Ha)
Germination %
3. To sow at rates under 30kg/Ha we
recommend using the Low Ratio.
2.Seed rates shown are approximate only
for the respective gearbox setting. It is
recommended that the calibration procedure
is always used. Refer to
page 16.
Pt. No. 67381
Issue 0511
21
Basic Calibration Procedure
Gearbox Setting Lever
To set the seed rate at the gearbox, slacken the tri knob (1) by
turning counter-clockwise and push from below into the position
indicated in the Sowing Chart. Retighten the star knob firmly
(Fig 6).
1
Important
The settings shown in the Sowing Charts (kg/ha) can only
serve as reference values. Deviations may occur caused by
differences in the size, shape, density of the grain and by the
dressing agent. Therefore prior to any sowing, always carry
out calibration trials to accurately determine the actual
seed rate.
Fig 6
Using the stepless variable speed gearbox, the speed of the
metering shaft and thus the seed rate is set steplessly. The
higher the figure indicated on the scale by the setting lever the
greater the seed rate (Fig 6).
Selecting the Gear Ratio
The Seed Drill is designed with a two speed (high and low) gear
ratio arrangement where the moving of the chain from a 21 x 13
teeth ratio to a 13 x 21 teeth ratio changes the output from high
to low (Fig 7). The selection and method for changing the ratio
is detailed under Speed Setting Page 27.
Fig 7
Setting Seeder Shutter Slides
The varying flow properties of seeds require different shutter
slide positions which may be found in the Sowing Chart for the
individual type of seed. This corresponds to one of the three
settings in Fig 8.
Fig 8/A
Fig 8/B
Fig 8/C
Closed
3/4 Open
Fully Open
C
A
B
Fig 8
Bottom Flap Settings
The various seed sizes require matching bottom flap clearances
below the metering wheel. The adjusting plate allows for 10
different settings. The required position for the seed type may
be found in the Sowing Chart. The control levers are located on
the LH end of the seedbox, (opposite end to the gearbox).
10
1
10
1
Number “1” corresponds to the minimum (closed) position and
“10” the maximum gap (Fig 9).
Fig 9
22
Basic Calibration Procedure
(Continued)
Seed Calibration
The calibration test should be done to confirm the required
seed rate and is done with the drill stationary and level.
2
1
Seed Calibration Procedures
1
Remove the calibration tray from the storage brackets
on the seedbox. Place the calibration tray (1) on the
support members below the seeders (Fig 10).
2
Position all the clear plastic seed diverters (2) to redirect
the seed into the calibration tray (Fig 10).
3
Make sure all the shutters are open and set to the
position indicated in the seed charts for the particular
seed.
4
Agitator Shaft - Check the Seed Chart “Hints” (Table 3)
whether to connect or disconnect the shaft by removing
the M10 bolt (1) during seeding (Fig 11).
5
For the test, half fill the box with seed. If this is not
possible make sure the seed is evenly distributed within
the box.
6
For setting method refer to Basic Calibration Procedures
(Page 22).
Fig 10
1
Fig 11
Note For seeds which are not covered in the respective
Sowing Chart (Page 19 to 21), use the figures for a seed of
comparable size and shape.
1
Fig 12
7
Place the crank handle (1) over the hexagonal drive dog
on the transfer shaft and turn anti-clockwise until the
seed flows consistently from the seeders (Fig 12). To
ensure complete filling of the seed unit continue turning
the crank until an even flow of seed is coming out of the
seeder units, then empty into the seedbox. The drill is
now ready for calibration.
8
Turn the crank handle anti-clockwise the required
number of revolutions as detailed in Table 5.
Note The Calibration is usually done for 1/40th hectare.
For very small seed rates or when using inaccurate
scales (i.e. unable to measure to the nearest gram) the
calculation based on 1/10th hectare should be used.
Scales must be accurate to 2 grams as any error will
be multiplied by either 10 or 40 giving inaccurate
calibration results.
Pt. No. 67381
Issue 0511
23
Basic Calibration Procedure (Continued)
Hand Crank Turns for Seed Rate Calibration
The tables represented below are for arable conditions (worked ground) and
are calculated to indicate an average situation. If there is any doubt as to the
accuracy of these figures for the conditions, it is advisable to run checks on
the calibration figures listed. Refer Page 26, (Wheel Slip Deviations). Check
and record which tyres are fitted to your drill, to ensure use of the correct
Hand Crank Turn and Constant figures.
Machine
Row
Sowing Width Turns for 1/40 Turns for 1/10
Size
Spacing(mm)
(m)
Hectare
Hectare
9
16 Run
180
2.88
32
127
20 Run
180
3.60
25
101
21 Run
147.5
3.10
29.5
118
24 Run
147.5
3.54
26
103
24 Run
125
3.00
30.5
122
28 Run
125
3.50
26
104
Weigh the seed collected during the test in kilograms.
Caution: Scales must be accurate to 2 grams, as any error will be multiplied
by either 10 or 40, giving inaccurate calibration results.
10 Calculate the seed rate by multiplying the kgs previously collected x 40 (1/40th
ha method, refer Table 6) or x 10 (1/10th ha method, refer Table 7) depending
on the requirement. If the resultant calculation does not produce the desired
seed rate use the enclosed seed rate calculator disc to determine the correct
gearbox setting.
Refer Use of Seed Rate Calculator Page 25.
Suggestion: To be on the safe side and until confidence has been gained
with the method of calibration it is advisable to conduct a second test at the
newly determined gearbox setting.
11 Where a coated seed is used it is advisable to check the calibration after
1 hectare as dressings can tend to create a coating on the seed metering
wheels thus changing the the flowing properties of the seed which in turn
alters the seed rate.
For 1/40 Hectare (250m2) Calibration
Seed Rate = Actual Seed Collected (kg) x 40
Table 6
For 1/10 Hectare (1000m2) Calibration
Seed Rate = Actual Seed Collected (kg) x 10
Table 7
24
Basic Calibration Procedure (Continued)
Use of Seed Rate Calculator
Determining the gear box scale setting using the calculator.
Usually the first calibration test yields a different seed rate. However with the value determined
from the first test it is possible to determine the correct gearbox setting with the aid of the
enclosed disc calculator (Fig 13). The disc calculator consists of 3 scales. An outer white scale
(1) for all seed rates above 30 kg/ha and an inner scale (2) for all seed rates below 30 kg/ha.
On the middle coloured scale (3) are all the gearbox setting numbers to a maximum value of
100.
Fig 13
Setting Example (Desired Seed Rate 125kg/ha)
1
2
3
4
From the calibration procedure at a gearbox lever setting of “70”, a seed rate of 175 kg/ha
is obtained.
Turn the inner disc until the measured seed rate of 175kg/ha (A) is in line with the related
actual gearbox setting of “70”(B) (Fig 13).
Read off from the disc rule the necessary gearbox setting for the required seed rate of
125kg/ha (C). In this example the correct setting is “50” (D) (Fig 13).
To be on the safe side the new gearbox setting can be checked by another calibration test.
Pt. No. 67381
Issue 0511
25
Basic Calibration Procedure (Continued)
Calibration Deviations
Deviations Between the Calibration Test and the Actual Seed Rate
The most frequent cause for changes between the calibration test and the seed rate lies in the
flowing properties of seed during sowing. These changes in properties generally result from
reactions of the dressing agents to temperature, humidity or abrasion. These changes will
become even more obvious when the bottom flaps are incorrectly set. If the setting of these
flaps leaves too large a gap an uncontrollable additional flow of seed can occur during seeding;
especially when assisted by the drill bouncing, a condition not simulated while conducting the
calibration tests. For this reason the basic setting of the bottom flaps should be checked at
regular intervals.
Residues from the seed dressing on the bottom flaps and metering wheels can also influence
the flowing properties of the seed and thus the seed rate. In such cases a balance will occur
only after a period of time and it is recommended to repeat the calibration test to confirm the
seed rate after 2-3 seedbox fillings, nominally when the seed box is half empty. Only then will a
balance occur and the seed rate will stabilise.
Wheel Slip Deviations
It is always possible with rubber tyred drills in extreme ground conditions to get wheel slip. Not
normally a problem with cleated type tyres in good condition, but more so in the arable situation
with the less agressive tread patterns. The result: large differences between the calibration test
and the actual sowing rate, obviously less seed deposited than required. The number of crank
turns indicated below is correct in most circumstances other than those mentioned above.
To check number of crank turns for calibration
Should you require to check this in a practical way proceed as follows:
For an area of 250m2 (1/40 Hectare), the travel distance for your machine is shown below.
Place the crank handle over the hexagonal drive dog on the gearbox. Move the machine
forward over the measured distance, counting the number of turns of the crank handle as you
go. Using this number of crank turns repeat the calibration.
Machine
Travel
Turns for 1/40 Sowing Width
Size
Distance (m)
Hectare
(m)
16 Run
86.8
32
2.88
20 Run
69.4
25
3.60
21 Run
80.7
29.5
3.10
24 Run
70.6
26
3.54
24 Run
83.3
30.5
3.00
28 Run
71.4
26
3.50
26
Hints for Sowing with Variable Speed
Gearbox
Fig 14
The gearbox allows for stepless changes in the speed of
the metering shaft and thus the seed rates. Due to the
variations in seed type and application rates there are two
speed ranges available.
By changing from High Speed to Low Speed the range of
settings and control is dramatically increased.
Change to the Low Speed when the gearbox setting is
down to 10 on the scale and the desired seed rate cannot
be obtained.
To change the speed setting from high to low, remove the
wing nut (1) and chain cover.(2) (Fig 14).
Release the tension on the chain (1) by forcing back the
chain tensioner (2) and hold in place with the hook. Refer
Figure 15. Remove the chain from the 21 tooth output
sprocket to the 13 tooth sprocket, then remove the chain
from the 13 tooth gearbox sprocket to the 21 tooth. Check
the chain is correctly aligned then release the chain
tensioner. Ensure the tension roller is correctly aligned
with the chain. Replace guard and calibrate as required.
1
2
Low Speed Shown
21T
To Determine the Gearbox Setting after a
Speed Change
For determining the correct gearbox setting after the speed
change, conduct the first test at 50. With the weight of
seed collected find your correct setting with the aid of the
disc calculator; refer Page 25, Fig 13.
13T
Fig 15
1
Sowing of Fine Seeds
For sowing small seeds the Renovator Drill is equipped as
standard with a combined normal and small seed metering
wheel (1). During grain sowing and other larger varieties of
seed both the large and small seed metering wheels are
coupled and both rotate. In order to convert the seed drill to
sow fine seed insert the crank handle and rotate clockwise
until the holes (2) of the small seed wheel are visible (Fig
16)
Using the tool supplied (3) disengage the the pin inside
the hole so that the large metering wheel rotates freely
on the metering shaft.
When seed is to be sown again using the normal metering
wheel press the pin, from the large metering wheel side
(opposite direction to before), using the tool, back into the
hole of the small seed wheel thus reconnecting the drive
between the two.
2
3
Fig 16
Pt. No. 67381
Issue 0511
27
Small Seeds
Calibration with Disconnected Agitator Shaft
The small seed metering wheel used in Duncan Drills is
especially well suited for sowing small seeds such as rape,
turnips and clover.
Due to the intensive action caused by the agitator the seeds
can adhere to each other, or be damaged, causing irregular
sowing/germination. Therefore it is recommended that
when sowing small seeds, especially oil seeds and thin
shelled seeds, the drive to the agitator is disconnected.
To do this remove the linch pin or bolt. (1) (Fig 18).
1
Fig 18
Deviations between the calibrated and actual seed rate can
occur when residual dressing agent sticks to the bottom
flaps and thus slows the flow of seed. Before beginning the
actual calibration test fill the calibration trays by turning the
crank handle at a high speed around the 90 setting on the
gearbox scale. This will cause an immediate buildup of the
dresssing agent on the flaps. Return the contents of the
calibration trays to the seed box and proceed with the actual
calibration. Due to the residue buildup on the flaps your
calibration will now reflect accurately the required seed rate.
Note - Remember to reconnect the agitator shaft as required
for other seeds otherwise the consistency of seed rate will be
affected.
A
B
Sowing Peas
Peas having the size and shape as illustrated in Fig 19A
(e.g. White Field Peas), can be sown in all Duncan Drills with
this type of metering wheel.
The flap should be set to a gap of at least “3” on the flap
setting lever (Page 22, Fig 9).
With these peas it should not be necessary to run the
agitator shaft.
Peas having the size and shape as illustrated in Fig 19B (e.g.
Green or Garden Peas), tend to bridge inside the seedbox
and do not flow freely.
This multi-faceted pea requires agitation for sowing.
Fig 19
Caution - When resetting the metering wheels
on the seeder shaft
Care should be taken when tightening the grub screws
on the small seed wheel. Adjust the grubscrew until the
movement of the metering wheel just stops, then tighten no
more than 1/8 of a turn.
Do not overtighten as this can result in breakages while
operating and may render the warranty on these units void.
28
Hectaremeter Settings Setup
Refer to the operation instructions supplied with your hectaremeter
kit for information and operation thereof. (Fig 21).
Computronics 1100 Area Meter Setup for Mk4 Renovator
The H1 value is the distance the machine travels in mm per pulse
detected on the pedestal drive shaft.
This is affected by:- jockey wheel diameter
- if there is wheel slip
- the gear ratio (13T on the jockey axle and 38T on the sensor mainshaft).
Fig 21
Ensure that the jockey wheel is inflated to the recommended pressure. (Page 5)
The H2 value is calculated from the number of rows x row spacing (in metres)
Machine
Row
Size
Spacing(mm)
H1
H2
16 Run
180
2.88
20 Run
180
3.60
21 Run
147.5
24 Run
147.5
24 Run
125
3.00
28 Run
125
3.50
Enter your value here>
2750
3.10
3.54
2750
H1
H2
It is advisable, as with all things electronic, to have a backup of your totals. We suggest you record
these on a daily basis in a notebook or diary.
Pt. No. 67381
Issue 0511
29
30
Renovator
Calibration Notes
Pt. No. 67381
Issue 0511
31
Maintenance & Care
General Safety and Accident Prevention Advice
1
Make sure that if the tractor remains attached to the drill
that the ignition key is removed.
2
During maintenance the drill should be supported in such
a manner that if hydraulic failure was to occur the machine
would still be adequately supported.
3
Wear gloves when handling components with cutting
edges such as worn discs etc...
4
Disconnect the electrical supply from the tractor before
doing any electrical maintenance.
5
Refer to safety sections for more safety information.
General Cautionary Maintenance Advice
1
Electric Welding - With the electronic equipment in
modern tractors it is advisable to completely disconnect the
implement from the tractor, or at the very least disconnect
the alternator before attempting any welding.
2
Hydraulics - Ensure hydraulic couplings (male & female)
are clean before connecting. Dirty couplings will result in
hydraulic oil contamination and hydraulic cylinder seal/
poppet valve damage and bore scores. This in turn will
result in oil leakage past the piston seals.
No filter is fitted to the hydraulic system. If hydraulic
fittings and oil supply are not going to be kept clean it is
recommended that a filter be fitted to prevent hydraulic
cylinder damage.
3
Water Blasting - Water blasting, steam cleaning or other
pressurised cleaning processes can force dirt etc. into
undesirable places that may cause damage or rapid part
wear to items such as bearings, seals, chains, bushes etc.
Caution must be exercised.
32
Maintenance & Care - Lubrication Instructions
Precautions with Grease
Greases should not be mixed as the structure may be weakened by the
mixes of different types of thickener, which may cause softening and loss of
grease from the bearings by running out.
Your new Duncan
Renovator Seed Drill
will give long and
efficient service if
given normal care and
maintained properly.
4
3
4
1
6
2
8
7
5
Fig 22
Lubrication Chart
Item
*
Components
Lubricant
Frequency
1
Wheel Bearings
Castrol LMX Grease
Annually
2
Wheel Leg Pivots
Castrol LMX Grease
Weekly
3
Gearbox
Castrol Oil Agri Trans Plus
Maintain Level
4
Drive Chains
Suitable Roller Chain Lubricant
See Maintenance Schedule
5
Disc Arm Castings
Castrol LMX Grease
Daily
6
Disc Opener Fr. Pivots Castrol LMX Grease
7
Turnbuckles
Castrol LMX Grease
Monthly
8
Coupling
Castrol LMX Grease
Weekly
Monthly
The lubrication frequencies are only a guide. Actual frequency will be dependent on extent of use and ground conditions.
Pt. No. 67381
Issue 0511
33
Maintenance & Care - Lubrication Instructions
Table 10
Daily
Weekly
Pre Season
(or after 20Ha)
(or after 75Ha)
(or 500 Ha)
Disc Openers
●
●
●
Depth Adjustment Collar
●
●
●
Seeders/Agitators/Bottom Flaps
●
●
●
Wheel Nuts
●
●
●
Pivot Pin Fasteners
●
●
Coupling & Safety Chains
●
●
Roller Chains
●
●
Gearbox
●
●
Hydraulics (Oil Leaks)
●
●
Tyre Pressures (58psi /4.0 bar)
●
●
Components
Bolted Connections
●
Maintenance Schedule
(Refer also to Summary Chart, above)
1 Bolted Connections
All bolted connections of the machine should be checked after the first 3 to 5 hours of operation and
retightened if necessary and thereafter at regular intervals. It is suggested that this is done every 500
hectares or annually, whichever occurs first.
2 Gearbox
The oil level in the gearbox can be seen in the oil gauge window. Changing the gearbox oil is
recommended once a year or sooner if the oil is discoloured. For refilling the oil remove the 1/2” BSP
plug on the top face of the gearbox, Castrol Oil Agri Trans Plus or equivalent* should be used.
The total filling capacity is 1.25 litres.
DO NOT OVERFILL.
*Oil Specification to meet the requirements of : SAE 10W-30, API GL-4, Massey Ferguson M1143,
John Deere J20C, J20D, Case MS 1207, Ford/New Holland M2C-134D, M2C-86 A/B/C
34
3 Drive Chains
All drive chains (1) (Fig 25) should first be checked
after every 20 hours of operation and thereafter
weekly or after 75Ha of operation as follows:The metering wheels of the seed drill are driven via
roller chains from the drive wheel.
Cleaning of the roller chains is recommended after
long periods of operation. Remove the chain, wash in
kerosene and then dip them in heated grease or oil
or spray them with a suitable commercial roller chain
lubricant.
1
1
1
4 Wheel Arm Pivots
Wheel arm pivots must be greased regularly (weekly
or after every 75Ha) to provide lubrication and flush
out any dirt. Refer Fig 26 (1).
5. Depth Adjustment Collar
Grease the depth adjustment collar (2) regularly to
ensure it does not seize up. Also check for dirt buildup
around the ram shaft seals to ensure seal damage
does not occur. Refer Fig 26
Fig 25
6. Tyre Pressure
The recommended tyre pressure is 4.0 bar (58
psi). Check the tyre pressure regularly to ensure
correct pressure is maintained. Weekly checks are
recommended.
2
1
7. Disc Openers
Front coulter bearings are sealed and do not require
lubrication. Check discs for any lateral movement
(wobble) on a regular basis. Replace bearings if there
is any noticeable wobble.
Fig 26
There is one grease nipple on each disc opener frame
pivot and disc assembly casting. Frame pivots should
be greased monthly while disc castings should be
greased daily to provide lubrication and to flush out
any dirt.
8. Length of Seed/Fertiliser Tubes
These tubes can stretch over a period of time and
require checking at approximately six monthly
intervals. Shorten if necessary to avoid bends which
will restrict the flow of seed/fertiliser.
9 Framework
The framework structure should be inspected annually
for defects, i.e., cracks in members or welded
connections. The framework should be cleaned prior
to the inspection.
Pt. No. 67381
Issue 0511
35
Maintenance & Care (Continued)
10 Bottom Flaps (Fig 28)
Im
po
rta
nt
2
!
1
3
4
5
The metering system should be checked every 1/2 year
or before any sowing period with an empty seed box
and empty metering housings.
Fig 28
1
Fig 29
The required seed rate is controlled by both the metering
wheels and the bottom flaps. The seed flows from the seed
box into the metering wheel housings. Inside the metering
wheel housing (1) the seed is caught between the metering
wheel (2) and the bottom flap (3). The metered amount
of seed is transported by the metering wheel to the edge
of the bottom flap where it drops off into the seed guide
tube which leads to the coulter. Varying grain sizes require
the matching of the flap clearance to the different grain
sizes. This matching is done by raising or lowering the
bottom flaps by using the flap adjusting lever on the LH
end of the seed box. If larger foreign particles, e.g. stones
get between the metering wheel and the bottom flap, the
bottom flap can give way downwards. A strong return
spring (4) brings the bottom flap immediately back into the
working position.
Use the following procedure:
Put the bottom flap setting levers (1) (located on the LH
end of the seed boxes) in position “1” for the front box and
position “1” for the rear box. Refer Fig 29.
By turning the metering wheel shaft by hand check the
flaps are all set to a gap of 0.1 to 0.5mm (refer Fig 28).
To adjust individual flaps use the spring tensioning screw
(5) (Fig 28).
Note: Maintenance Schedule (page 24)
Where the frequency is given in terms of use (eg. weekly) or
area covered (eg. 75 Ha) perform the maintenance task based
on whichever occurs first.
Preparing the Machine for Storage.
Locate on a dry level surface. The machine should be stored
wherever possible so the rams are not supporting any weight.
The drive chains should be lubricated with suitable roller chain
lubricant before prolonged periods of storage.
For longer term storage remove seed/fertiliser tubes from the
boot assembly and allow to hang without deformation. Check
tube lengths when replacing.
It is recommended that maintenance be carried out at the end
of the season, giving sufficient time to obtain spare parts and/
or carry out repairs if required.
36
Renovator
Problem
Possible Cause
Troubleshooting
Action
Jockey wheel under inflated
Check pressure
Are the hectare meter settings correct? Check settings
Has the calibration procedure been
followed correctly?
Over Sowing
Is the shutter slide open too wide?
5
29
22-24
22-24
Is the flap setting open too wide?
Check settings
22-24
Too larger gap between seeder unit &
bottom flap (should be 0.3mm when on
setting 1)
Check settings
32
Check gap
18
Quadrant Tri-knob coming loose
Under Sowing
Re-calibrate
Refer to Page…
Has the calibration procedure been
followed correctly?
Re-calibrate
Is the correct gear ratio selected?
Check setting
22-24
27
Sowing at shallow depths. Is there
Check and adjust spring
sufficient pressure on the jockey wheel? pressure
Drill not sowing
until quadrant
levers are well
down on the
scale/each box is
sowing at different
rate even when
both set on the
same setting
Drill sowing
deeper on one
side/leaking down
on one side
Tines are moving
Drill not
penetrating into
ground/drill riding
out of ground
The two bolts on the quadrant lever have
come loose
Transfers may not be aligned with each
other
Hydraulic lift rams have not rephased
properly
Dirt in the poppet valve of the ram
Check and reset
70-71
Rephase rams
38
Clean/replace valve
38
Too much turning with drill in the ground Keep turning to minimum
Operating drill in the float position
Disc openers are keeping the drill from
penetrating into the ground
Do not operate in float
15
Lift discs out of the ground
16
Pt. No. 67381
Issue 0511
37
Commisioning PTE Phasing Cylinders
1. General
(a) PTE cylinders will re-phase in both directions. Each piston is fitted with 2 poppet valves which open at
the end of the stroke to allow oil to bypass the piston. The bypass of oil at the end of the stroke allows for
initial bleeding of the system and re-phasing in operation.
(b) The valve in the piston is a precision device, CLEANLINESS IS OF THE UTMOST IMPORTANCE.
Contamination in the oil will accelerate deterioration of the valve seat. Cylinders will creep once the
integrity of the seating is lost.
2. Bleeding the System
(a) Initial bleeding after connection to the tractor
Purge all air from the system by fully stroking rams in both directions. Allow the oil to flow through the
cylinders with the tractor at an idle for a minimum of 2 minutes at each end of the stroke.
(b) Re-phasing after initial bleeding
After initial bleeding the cylinders will only require occasional re-phasing during operation. This is done by
extending the rams for about 30 seconds or until all cylinders have reached the end of their stroke.
3. Fault Finding
1. Cylinders creeping during operation
There are two primary causes of this:
(i) Air in the hydraulic system
(ii) By passing of the poppet valve.
(a) Check that there is no air in the system. Raise and lower the machine. All cylinders should move
instantaneously, any lag indicates that there is air in the system. Other signs of air in the system are hoses
vibrating/squealing or the control handle shuddering. Re-bleed the system if necessary.
(b) If there is no sign of air in the system and the cylinders still creep, raise the machine off the depth stop
and measure the movement of each cylinder rod.
(c) If both cylinders move at the same rate it is likely to be the control valve/lock out valve that is leaking.
(d) If the slave continues moving after the master cylinder has hit the depth stop it is likely to be the piston
in the master cylinder that is bypassing.
(e) If the slave cylinder extends while the master cylinder retracts it is likely to the the piston in the master
cylinder that is bypassing.
(f) If the master cylinder does not move but the slave does it is likely to be the piston in the slave cylinder
that is bypassing.
(g) If the piston is bypassing it is likely to be contamination in the phasing valve. The cylinder will have to
be dismantled, cleaned and fitted with a new poppet valve.
38
Commisioning PTE Phasing Cylinders (continued)
3. Fault Finding (continued)
2. Cylinders moving at different rates
(a) Check that there is no air in the system. Raise and lower the machine; all cylinders should move at the
same time, any lag indicates that there is air in the system. Re-bleed the system if necessary.
(b) Ensure that the cylinders have been connected correctly. The cylinders should be connected in series
so that the bore sizes go down in 1/4” increments. The Rod end port of the master cylinder (3.5” bore) is
connected to the piston end port of the slave cylinder (3.25” bore).
Pt. No. 67381
Issue 0511
39
40
41
Full
3/4
3/4
3/4
Full
Full
Full
3/4
3/4
3/4
3/4
3/4
3/4
3/4
Full
Full
Full
Full
H
H
H
H
H
H
H
H
L
L
L
L
L
L
H
H
L
L
Barley
Ryecorn
White Peas
Green Peas
Peren. Grass
Annual Grass
Pasture Mix*
Lucerne
Turnip
Kale
Swedes
Rape
White Clover
Red Clover
Super Phosphate
DAP Granules
Super Phosphate
DAP Granules
3
3
3
3
1
1
1
1
1
1
1
3
3
3
3
3
3
3
3
3
0.7
0.8
0.8
6.6
5.3
15
1.6
1.3
1.3
1.3
1.4
1.5
11
13
11
20
75
2.9
2.5
2.5
2.6
2.6
7.4
22
26
22
64
92
30
50
98
97
81
84
Closed
3/4
Full
60
70
80
90
100
121 146 170 197 221
119 144 168 194 218
101 120 141 161 180
105 125 148 170 192
5.5
4.6
4.8
4.9
4.9
15
44
50
44
6.7
18
55
63
55
8.0
21
66
66
128 157 189 224 259 292
44
58
74
90
Connected
20 Run
16 Run
180
180
2750
H1
Hectaremeter Settings
109 120
Connected
Connected
Connected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Connected
Connected
Connected
Connected
Disconnected
Connected
Connected
Connected
Connected
Connected
Agitator Shaft
180
Machine
Row
Size
Spacing(mm)
95
108 125 150
143 175 211 247 284 314
115 152 193 235 282 325 374
4.1
3.7
3.6
3.9
3.8
11
34
38
34
96
133 175 202 250 294 325 374
40
Metering Wheel* N=Normal (Both)
F= Fine (Small)
N
N
N
N
F
F
F
F
F
F
F
N
N
N
N
N
N
N
N
N
Type
Gearbox Setting Position
Seed Rate (kg/ha)
3.60
2.88
H2
High & Low Ratio - Wide Row Spacing 180mm
Disconnect/connect Agitator Shaft
180
20 Run
3.60
2.88
32
25
HANDY HINTS
For 1/10 Hectare
Seed Rate = Actual Seed Collected (kg) x 10
For 1/40 Hectare
Seed Rate = Actual Seed Collected (kg) x 40
101
127
www.duncanag.co.nz
When fitted, disc opener should run approx 20mm deeper than boot
Keep turning in ground to a minimum
P/N 45658
For accurate seeding, ensure jockey wheel is inflated to maximum
pressure shown on the tyrewall
For products not on sowing chart choose a similar product
Bottom Flap: check gap setting (0.3mm) regularly to avoid inconsistent
seeding and or seed damage. REFER TO MANUAL
For seed rates under 30kg/Ha >use LOW RATIO
Keep a constant pace during calibration turns
11
10 Weigh seed (scales must be accurate to within 2 grams)
180
16 Run
Machine
Row
Sowing Width Turns for 1/40 Turns for 1/10
Size
Spacing(mm)
(m)
Hectare
Hectare
9 Turn the crank handle anti-clockwise the required number of
revolutions.
8 Place the crank handle over the hex drive and turn anti-clockwise
until the seed flows consistently from all seeder units then empty
into the seedbox.
7 Select gearbox setting
6
5 Set Bottom Flap
4 Set Shutter Slide
3 Select gear ratio
2 Position all the clear plastic seed diverters to redirect the seed
into the calibration tray
1 Place the calibration tray in the brackets
Seed Calibration Procedures
The calibration test should be done to confirm the required seed rate
and is done with the drill stationary and level.
Seed Calibration
Basic Calibration Procedure
Seed rates shown are approximate only for the respective gearbox setting. It is recommended that the calibration procedure is always used.
13T
Low Speed Shown
Full
H
Oats
21T
Bottom Flap*
Position
3/4
H
Hi/Low
Shutter
Slide*
Wheat
PRODUCT
Metering
Wheel*
Renovator Seed Drill Sowing Chart
Calibration Chart and Handy Hints (16R 3m & 20R 3.5m)
Pt. No. 67381
Issue 0511
42
Full
Full
3/4
3/4
3/4
Full
Full
Full
3/4
3/4
3/4
3/4
3/4
3/4
3/4
Full
Full
H
H
H
H
H
H
H
H
H
L
L
L
L
L
L
H
H
Oats
Barley
Ryecorn
White Peas
Green Peas
Peren. Grass
Annual Grass
Pasture Mix*
Lucerne
Turnip
Kale
Swedes
Rape
White Clover
Red Clover
Super Phosphate
DAP Granules
3
3
1
1
1
1
1
1
1
3
3
3
3
3
3
3
3
3
0.9
1.2
1.2
10
7.7
15
2.2
1.9
1.9
1.9
2.0
2.1
17
19
17
20
40
Closed
3/4
Full
60
70
80
90
100
141 175 211 245 285 320
140 172 208 243 281 315
117 146 173 204 233 260
121 152 180 213 246 277
50
5.9
5.3
5.2
5.6
5.4
17
49
55
49
7.9
6.6
6.9
7.1
7.1
21
64
72
64
10
26
79
91
79
12
31
96
96
139 185 227 274 323 374 422
Connected
Connected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Connected
Connected
Connected
Connected
Disconnected
Connected
Connected
Connected
Connected
Connected
Agitator Shaft
125
125
125
24 Run
28 Run
Machine
Row
Size
Spacing(mm)
2750
H1
Hectaremeter Settings
206 253 304 358 410 453
108 166 219 278 340 407 470 541
4.2
3.7
3.6
3.8
3.8
11
32
38
32
92
133 192 252 291 361 425 470 541
30
Metering Wheel* N=Normal (Both)
F= Fine (Small)
N
N
F
F
F
F
F
F
F
N
N
N
N
N
N
N
N
N
Type
Gearbox Setting Position
Seed Rate (kg/ha)
3.50
3.00
H2
High & Low Ratio - Narrow Row Spacing 125mm
Disconnect/connect Agitator Shaft
125
28 Run
3.50
3.00
26
30.5
HANDY HINTS
For 1/10 Hectare
Seed Rate = Actual Seed Collected (kg) x 10
For 1/40 Hectare
Seed Rate = Actual Seed Collected (kg) x 40
104
122
www.duncanag.co.nz
When fitted, disc opener should run approx 20mm deeper than boot
Keep turning in ground to a minimum
P/N 45642
For accurate seeding, ensure jockey wheel is inflated to maximum
pressure shown on the tyrewall
For products not on sowing chart choose a similar product
Bottom Flap: check gap setting (0.3mm) regularly to avoid inconsistent
seeding and or seed damage. REFER TO MANUAL
For seed rates under 30kg/Ha >use LOW RATIO
Keep a constant pace during calibration turns
11
10 Weigh seed (scales must be accurate to within 2 grams)
125
24 Run
Machine
Row
Sowing Width Turns for 1/40 Turns for 1/10
Size
Spacing(mm)
(m)
Hectare
Hectare
9 Turn the crank handle anti-clockwise the required number of
revolutions.
8 Place the crank handle over the hex drive and turn anti-clockwise
until the seed flows consistently from all seeder units then empty
into the seedbox.
7 Select gearbox setting
6
5 Set Bottom Flap
4 Set Shutter Slide
3 Select gear ratio
2 Position all the clear plastic seed diverters to redirect the seed
into the calibration tray
1 Place the calibration tray in the brackets
Seed Calibration Procedures
The calibration test should be done to confirm the required seed rate
and is done with the drill stationary and level.
Seed Calibration
Basic Calibration Procedure
Seed rates shown are approximate only for the respective gearbox setting. It is recommended that the calibration procedure is always used.
13T
Low Speed Shown
3/4
21T
Bottom Flap*
Position
H
Hi/Low
Shutter
Slide*
Wheat
PRODUCT
Metering
Wheel*
Renovator Seed Drill Sowing Chart
Calibration Chart and Handy Hints (24R 3m & 28R 3.5m)
43
L
L
L
L
L
Turnip
Kale
Swedes
Rape
White Clover
Full
Full
Full
Full
3/4
3/4
3/4
3/4
3/4
3/4
3/4
Full
Full
Full
3/4
3/4
3/4
Full
Full
3/4
13T
0.8
1.0
1.0
8.1
6.5
15
1.9
1.6
1.6
1.6
1.7
1.8
14
16
14
20
40
3/4
Full
60
70
80
90
100
123 146 172 197 220
119 148 178 207 241 270
118 145 176 205 237 266
99
102 128 152 180 208 234
50
Gearbox
91
3.6
3.1
3.0
3.2
3.2
9.0
27
32
27
78
6.7
5.6
5.8
6.0
6.0
18
54
61
54
8.2
22
67
77
67
9.8
26
81
81
54
71
90
Connected
Connected
Connected
Connected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Disconnected
Connected
Connected
Connected
Connected
Disconnected
Connected
Connected
Connected
Connected
Connected
Agitator Shaft
147.5
147.5
147.5
21 Run
24 Run
Machine
Row
Size
Spacing(mm)
2750
H1
Hectaremeter Settings
116 133 147
110 132 152 183
174 214 257 302 346 383
140 185 235 287 344 397 457
5.0
4.5
4.4
4.7
4.6
14
41
46
41
117 156 192 231 273 316 356
112 162 213 246 305 359 397 457
30
Setting Position
Seed Rate (kg/ha)
3.54
3.098
H2
High & Low Ratio - Standard Row Spacing 147.5mm
Metering Wheel* N=Normal (Both)
F= Fine (Small)
N
N
N
N
F
F
F
F
F
F
F
N
N
N
N
N
N
N
N
N
Type
Closed
Bottom Flap*
Disconnect/connect Agitator Shaft
147.5
24 Run
3.54
3.098
26
29.5
HANDY HINTS
For 1/10 Hectare
Seed Rate = Actual Seed Collected (kg) x 10
For 1/40 Hectare
Seed Rate = Actual Seed Collected (kg) x 40
118
103
www.duncanag.co.nz
When fitted, disc opener should run approx 20mm deeper than boot
Keep turning in ground to a minimum
P/N 45643
For accurate seeding, ensure jockey wheel is inflated to maximum
pressure shown on the tyrewall
For products not on sowing chart choose a similar product
Bottom Flap: check gap setting (0.3mm) regularly to avoid inconsistent
seeding and or seed damage. REFER TO MANUAL
For seed rates under 30kg/Ha >use LOW RATIO
Keep a constant pace during calibration turns
11
10 Weigh seed (scales must be accurate to within 2 grams)
147.5
21 Run
Machine
Row
Sowing Width Turns for 1/40 Turns for 1/10
Size
Spacing(mm)
(m)
Hectare
Hectare
9 Turn the crank handle anti-clockwise the required number of
revolutions.
8 Place the crank handle over the hex drive and turn anti-clockwise
until the seed flows consistently from all seeder units then empty
into the seedbox.
7 Select gearbox setting
6
5 Set Bottom Flap
4 Set Shutter Slide
3 Select gear ratio
2 Position all the clear plastic seed diverters to redirect the seed
into the calibration tray
1 Place the calibration tray in the brackets
Seed Calibration Procedures
The calibration test should be done to confirm the required seed rate
and is done with the drill stationary and level.
Seed Calibration
Basic Calibration Procedure
Seed rates shown are approximate only for the respective gearbox setting. It is recommended that the calibration procedure is always used.
21T
3
3
3
3
1
1
1
1
1
1
1
3
3
3
3
3
3
3
3
3
Position
Shutter
Slide*
Low Speed Shown
L
H
Lucerne
DAP Granules
H
Pasture Mix*
L
H
Annual Grass
Super Phosphate
H
Peren. Grass
H
H
Green Peas
DAP Granules
H
White Peas
L
H
Ryecorn
H
H
Barley
Super Phosphate
H
Oats
Red Clover
H
Hi/Low
Wheat
PRODUCT
Metering
Wheel*
Renovator Seed Drill Sowing Chart
Calibration Chart and Handy Hints (21R 3m & 24R 3.5m)
Pt. No. 67381
Issue 0511
Renovator
44
Maintenance Notes
Pt. No. 67381
Issue 0511
45
46
Parts List
‘Mk4 Renovator’ Seed Drill
Head Office:
P.O. Box 2018
Hilton Highway, Washdyke
Timaru, New Zealand
Telephone (03) 688 2029
Facsimile (03) 688 2821
Australian Branch:
4B Silverton Close
Laverton North 3026
Melbourne, Australia
Telephone (03) 9314-9666
Facsimile (03) 9314-6810
Pt. No. 67381
Issue 0511
47
‘Renovator’ Seed Drill
Dual Box Complete Assembly
19
17
20
13, 14
10
26
1
8
15
2
11
12
27
17
18
27
21 22
28
23
8
16
3
5
6
48
‘Renovator’ Seed Drill
ITEM
PART No.
1
Refer pages 52-55
Dual Box Complete Assembly
DESCRIPTION
QTY
Main Frame and Drawbar Assembly
1
2
Refer pages 56
Wheel Leg
1
3
Refer pages 58-59
Wheel Hydraulics
1
4
Refer pages 88-89
Wiring and Lighting (Optional - not shown)
1
5
Refer pages 84-85
Disc Opener Assembly (Optional)
1
6
Refer pages 60-61
Tine and Boot Assembly
-
7
Refer pages 62-63
Drive Chains (Not shown)
-
8
Refer pages 68-69
Jockey Wheel and Transfer Drive System
1
9
Refer pages 81
Hectaremeter Kit (Not shown)
1
10
Refer page 67
Seed Box Drive Shafts
2
11
Refer page 70-71
Gearbox Final Assembly
1
12
Refer pages 72-75
Seedbox Assembly
2
13
Refer page 78
Agitator Drives
2
14
Refer page 79
Agitator Shaft Assembly (Inside Seedbox)
2
15
Refer page 80
Seeder Mechanism
-
16
60150
16/21/24 Run 3.0m Footboard Assembly
1
16
60350
20/24/28 Run 3.5m Footboard Assembly
1
17
Refer pages 72-75
16/21/24 Run 3.0m Calibration Tray
4
17
Refer pages 72-75
20/24/28 Run 3.5m Calibration Tray
4
18
60092
Drive Guard
1
19
60160
Safety Rail 3.0m
2
19
60360
Safety Rail 3.5m
2
20
60163
End Safety Rail 3.0/3.5m
1
21
25730
Jockey Arm Tension Spring
1
22
25723
Jockey Arm Tension Eyebolt
1
23
60175
Footboard Step
1
24
22051
Crank Arm and Handle Assy
1
25
60240
3.0m Weather Skirt (Not shown)
2
25
60242
3.5m Weather Skirt (Not shown)
2
26
60077
LH Pedestal W/Assy (Dual)
1
27
60081
Drive Pedestal W/Assy
1
28
26599
Calibration Tray Bracket
8
Pt. No. 67381
Issue 0511
49
‘Renovator’ Seed Drill
Single Box Complete Assembly
19
20
24
27
1
13, 14
26
5
2
11
12
3
8
21 22
23
17
16
10
15
8
6
50
‘Renovator’ Seed Drill
Single Box Complete Assembly
ITEM
PART No.
DESCRIPTION
QTY
1
Refer pages 52-55
Main Frame and Drawbar Assembly
1
2
Refer pages 56-57
Wheel Leg
1
3
Refer pages 58-59
Wheel Hydraulics
1
4
Refer pages 88-89
Wiring and Lighting (Optional - not shown)
1
5
Refer pages 84-85
Disc Opener Assembly (Optional)
1
6
Refer pages 60-61
Tine and Boot Assembly
-
7
Refer pages 62-63
Drive Chains (Not shown)
-
8
Refer pages 68-69
Jockey Wheel and Transfer Drive System
1
9
Refer pages 81
Hectaremeter Kit (Not shown)
1
10
Refer page 67
Seed Box Drive Shafts
2
11
Refer page 70-71
Gearbox Final Assembly
1
12
Refer pages 76-77
Seedbox Assembly
2
13
Refer page 78
Agitator Drives
2
14
Refer page 79
Agitator Shaft Assembly (Inside Seedbox)
2
15
Refer page 80
Seeder Mechanism
-
16
60150
16/21/24 Run 3.0m Footboard Assembly
1
16
60350
20/24/28 Run 3.5m Footboard Assembly
1
17
Refer pages 76-77
16/21/24 Run 3.0m Calibration Tray
4
17
Refer pages 76-77
20/24/28 Run 3.5m Calibration Tray
4
18
60092
Drive Guard
1
19
60160
Safety Rail 3.0m
2
19
60360
Safety Rail 3.5m
2
20
60163
End Safety Rail 3.0/3.5m
1
21
25730
Jockey Arm Tension Spring
1
22
25723
Jockey Arm Tension Eyebolt
1
23
60175
Footboard Step
1
24
22051
Crank Arm and Handle Assy
1
25
60240
3.0m Weather Skirt (Not shown)
1
25
60242
3.5m Weather Skirt (Not shown)
1
26
60225
LH Pedestal W/Assy (Single)
1
27
60081
Drive Pedestal W/Assy
1
28
26599
Calibration Tray Bracket
4
Pt. No. 67381
Issue 0511
51
‘Renovator’ Seed Drill
7
17
10
Mainframe and Drawbar
9
14 15
13
1
2
5
12
6
3
8
20
23
4
20
16
21
22
18
19
24
25 26 27 28
8
11
52
‘Renovator’ Seed Drill
Mainframe and Drawbar
ITEM
PART No.
DESCRIPTION
QTY
1
60000
3.0m Mainframe (16/21/24 Run)
1
1
60200
3.5m Mainframe (20/24/28 Run)
1
2
Refer Pages 60-61
Coil Tines & Boots
-
3
60033
Drawbar Welded Assembly
1
4
4800315
Hose Support
1
5
60094
Drawbar Axle
1
6
45285
Roll Pin
2
7
60192
Centre Hitch Welded Assembly
1
8
60405
Towing Eye Assembly
1
9
26577
LH Support Stay
1
10
26578
RH Support Stay
1
11
43832
Safety Chain Assembly
2
12
45066
M20 x 70 Grade 8.8 Bolt
4
13
45141
M20 Nyloc Nut
6
14
47244
7/8” UNF Bolt x 6.5”
1
15
47548
7/8” UNF Nut
1
16
45181
M8 x 12 S/H Grub Screw
1
17
45075
M20 x 150 Grade 8.8 Bolt
1
18
45042
M16 x 60 Grade 8.8 Bolt
4
19
45140
M16 Nyloc Nut
4
20
45033
M12 x 120 Grade 8.8 Bolt
2
21
45139
M12 Nyloc Nut
3
22
60409P
Hose Rack
1
23
Refer Pages 90-91
Stand Kit – Optional
1
24
43007
Grease Nipple
1
25
22262
Clevis Pin Tabbed
1
26
45001s
M10 x 20 S/Screw Grade 8.8 ZP
1
27
45152
M10 Light Flat Washer
1
28
45166
M10 Spring Washer
1
Pt. No. 67381
Issue 0511
53
‘Renovator’ Seed Drill
3
4
1
2
Mainframe and Drawbar
4
Note: Drawbar hydraulic parts can be
purchased as a kit.
The part number is 26720K.
13
14
8
9
5
6
12
13
7
10 11
54
15
‘Renovator’ Seed Drill
ITEM
PART No.
Mainframe and Drawbar
DESCRIPTION
QTY
Drawbar Turnbuckle Parts
1
43395
H/D Ratchet Turnbuckle
1
2
47254
Bolt 1” UNF x 5” HT
1
3
47251
Bolt 1” UNF x 3.5” HT
1
4
47552
1” UNF Nyloc Nut
2
Drawbar Hydraulic Parts
5
43852
Hydraulic Cylinder
1
6
26723
Hydraulic Hose 2.80m
1
7
26724
Hydraulic Hose 2.50m
1
8
43496
3/4” UNO to 3/8”BSPT Elbow
1
9
43393
3/8” BSP S/S Ball Valve
1
10
43147
1/2” BSP Quick Release Coupling
2
11
43617
Dust Cover
2
12
43280
3/4” UNO to 3/8” BSPM Nipple
1
13
47552
1” UNF Nyloc Nut
2
14
47254
Bolt 1” UNF x 5” HT
1
15
47251
Bolt 1” UNF x 3.5” HT
1
Pt. No. 67381
Issue 0511
55
‘Renovator’ Seed Drill
Wheel Leg
10
11
9
2
12
3
13
8
1
13
6
7
2
4
5
3
56
‘Renovator’ Seed Drill
Wheel Leg
ITEM
PART No.
DESCRIPTION
QTY
1
60045PH
Left Hand Wheel Leg (not shown)
1
1
60061PH
Right Hand Wheel Leg
1
2
60247
Pivot Pin
2
3
60065
Spacer
4
4
45619
Lock Washer
2
5
45618
Lock Nut
2
6
45648
Hub and Stub
2
7
45638
Wheel
2
8
43010
90° Grease Nipple
2
9
60059p
Wheel Scraper
2
10
45030
M12 x 90 Gr 8.8 Z/P Bolt
4
11
45159
M12 HD Washer
4
12
45139
M12 Nyloc Nut
4
13
43426
Glacier Bush Ø45
4
14
Call
Hub Rebuild kit
-
Pt. No. 67381
Issue 0511
57
‘Renovator’ Seed Drill
Wheel Hydraulics
3
6
15
2
15
Slave
Cylinder
5
1
Master
Cylinder
7
4
13, 14
4
8
10
17
19
9
10
24, 25
5
18
12
9
11
16
58
20 - 23
‘Renovator’ Seed Drill
Wheel Hydraulics
ITEM
PART No.
DESCRIPTION
QTY
1
26702
3.5” x 6.5” Master Rephasing Cylinder (Includes pin)
1
2
26703
3.25” x 6.5” Slave Rephasing Cylinder (Includes pin)
1
3
43848
Stroke Limiting Collar 7/8” (where fitted)
1
4
60866
Hydraulic Hose, 2.70m (3.0m and 3.5m machines)
1
5
60864
Hydraulic Hose, 2.70m (3.0m machine)
1
5
60869
Hydraulic Hose, 2.80m (3.5m machine)
1
6
60864
Hydraulic Hose, 2.70m (3.0m machine)
1
6
60868
Hydraulic Hose, 3.10m (3.5m machine)
1
7
60863
Hydraulic Hose, 5.45m (3.0m machine)
1
7
60867
Hydraulic Hose, 5.70m (3.5m machine)
1
8
43028
3/8” Flow Control
1
9
43391
3/8” Dowty Washer
3
10
43392
3/8” BSPP Male Nipple
2
11
43393
3/8” BSP S/S Ball Valve
1
12
60856
Hydraulic Valve Support Assy
1
13
43147
1/2” BSP Quick Release Coupling
2
14
43617
Dust Cover
2
15
43280
3/4” UNO to 3/8” BSP Nipple
4
16
45033
M12 x 120 Bolt
1
17
45139
M12 Nyloc Nut
1
18
44957
M6 X 50 Bolt
2
19
45136
M6 Nyloc Nut
2
20
22270
Clevis Spacer
2
21
22262
Clevis Pin Assembly
2
22
45418s
M10 x 25 Set Screw
2
23
45166
M10 Spring Washer
2
24
26558
Clevis Pin
2
25
45272
R Clip
2
Pt. No. 67381
Issue 0511
59
‘Renovator’ Seed Drill
Tine and Boot Assembly
11
12
10
1
Left Hand
Tine Shown
7
5
2
9
8
13
14
3
9
4
60
‘Renovator’ Seed Drill
ITEM
PART No.
Tine and Boot Assembly
DESCRIPTION
3.0m
3.5m
16R
21R
24R
20R
24R 28R
1
21413
LH Coil Tine
8
11
12
10
11
14
1
21414
RH Coil Tine
8
10
12
10
13
14
2
26848
LH Inverted Tee Clamp
16
21
24
20
24
28
3
25615
RH Inverted Tee Clamp
16
21
24
20
24
28
4
26849
Cast Inverted Tee Point
16
21
24
20
24
28
5
25608
Fertilizer Tube, Standard (dual box)
12
17
20
16
20
24
6
25613
Fertilizer Tube, Angle (dual box)
4
4
4
4
4
4
7
45010
M10 x 65 Bolt, Class 8.8
32
42
48
40
48
56
8
45003
M10 x 30 Bolt, Class 8.8
32
42
48
40
48
56
9
45138
M10 Nyloc Nut
64
84
96
80
96
112
10
21691
Tine Clamp Casting
32
42
48
40
48
56
11
45466
M16 x 80 (4.6) Zinc Plated Bolt
32
42
48
40
48
56
12
21690
75 x 75 RHS Clamp Plate
16
21
24
20
24
28
13
45413
M8 x 35 Bolt (dual box)
16
21
24
20
24
28
14
45137
M8 Nyloc Nut (dual box)
16
21
24
20
24
28
15
43691
Feed Hose 38mm
-
Pt. No. 67381
Issue 0511
61
‘Renovator’ Seed Drill
Drive Chains Dual Box
ITEM
PART No.
DESCRIPTION
QTY
1
25724
13 T Sprocket 1/2” P x 20mm Bore
1
2
25742
38 T Sprocket 1/2” P x 25mm Bore
1
3
26352
13T/21T Crank Sprocket
1
4
26350
13T/21T Change Sprocket
1
5
22044
15 T Sprocket 1/2” P x 20mm Bore
2
6
22537
25 T Sprocket 1/2” P x 20mm Bore
2
7
24103
1/2” BS Chain x 61 Links (Jockey Wheel Drive)
1
8
60269
1/2” BS Chain x 87 Links (Transfer Shaft to Gearbox input)
1
9
25780
1/2” BS Chain x 47 Links (Gearbox to Boxshaft)
2
10
Refer page 66
Chain Tensioner Jockey Wheel Drive
1
11
Refer page 64-65
Chain Tensioner Transfer Drive
1
12
Refer page 64
Rear Chain Tensioner Box Shaft
1
13
Refer page 64
Front Chain Tensioner Box Shaft
1
14
22294
Sprocket Key (6 x 6 x 25)
8
15
45180
M8 x 10 Socket Head Grub Screw
14
16
45181
M8 x 12 Socket Head Grub Screw
2
17
43388
1/2” Pitch Joining Link
4
18
45065
M20 x 65 8.8 Bolt Z/P
1
19
45120
M20 8.8 Half Nut Z/P
1
20
45141
M20 Nyloc Nut
1
9
9
5
6
4
5
6
13
12
11
8
7
3
1
A welded stop has replaced items
18, 19 & 20 from May 2011.
18
2
19
10
20
62
‘Renovator’ Seed Drill
Drive Chains Single Box
ITEM
PART No.
DESCRIPTION
QTY
1
25724
13 T Sprocket 1/2” P x 20mm Bore
1
2
25742
38 T Sprocket 1/2” P x 25mm Bore
1
3
26352
13T/21T Crank Sprocket
1
4
26350
13T/21T Change Sprocket
1
5
22044
15 T Sprocket 1/2” P x 20mm Bore
2
6
22537
25 T Sprocket 1/2” P x 20mm Bore
2
7
24103
1/2” BS Chain x 61 Links (Jockey Wheel Drive)
1
8
60269
1/2” BS Chain x 87 Links (Transfer Shaft to Gearbox input)
1
9
25781
1/2” BS Chain x 37 Links (Gearbox to Boxshaft)
1
10
Refer page 66
Chain Tensioner Jockey Wheel Drive
1
11
Refer page 65
Chain Tensioner Transfer Drive
1
12
22294
Sprocket Key (6 x 6 x 25)
6
13
45180
M8 x 10 Socket Head Grub Screw
8
14
45181
M8 x 12 Socket Head Grub Screw
2
15
43388
1/2” Pitch Joining Link
3
16
45065
M20 x 65 8.8 Bolt Z/P
1
17
45120
M20 8.8 Half Nut Z/P
1
18
45141
M20 Nyloc Nut
1
9
5
6
4
A welded stop has replaced items
16, 17 & 18 from May 2011.
11
8
7
3
1
16
2
17
10
18
Pt. No. 67381
Issue 0511
63
‘Renovator’ Seed Drill
Chain Tensioners
ITEM
PART No.
1
22535
Nylon Roller
2
2
22480
Arm Assembly, RH
2
3
22522
Torsion Spring, LH
1
4
22523
Torsion Spring, RH
1
5
23376
Chain Tensioner Anchor
2
6
45132
M16 Hex Nut
2
7
45462
M16 x 60 Bolt
2
5
DESCRIPTION
QTY
7
4
1
6
2
2
1
4
5
6
7
64
‘Renovator’ Seed Drill
DESCRIPTION
Chain Tensioners
ITEM
PART No.
QTY
1
22535
Nylon Roller
1
2
25984
Arm Assembly, RH, 60 Extension
1
3
22523
Torsion Spring, RH
1
4
45132
M16 Hex Nut
1
5
45461
M16 x 55 Bolt
1
2
1
4
3
5
Pt. No. 67381
Issue 0511
65
‘Renovator’ Seed Drill
Chain Tensioners
ITEM
PART No.
DESCRIPTION
1
22535
Nylon Roller
2
23373
Short Arm Assembly, LH
1
3
22523
Torsion Spring, RH
1
4
23376
Chain Tensioner Anchor
1
5
45119
M16 Half Nut
1
6
45462
M16 x 60 Bolt
1
3
QTY
1
2
6
4
5
1
66
‘Renovator’ Seed Drill
Seed Box Drive Shafts
ITEM
PART No.
DESCRIPTION
1
22537
Sprocket, 25T x 1/2” Pitch
2
22294
Key, Sprocket 6 x 6 x 25
1
3
25758
Shaft, Box Drive
1
4
43385
“Y” Bearing
2
5
43387
Housing, Bearing, Press Steel (2 Flanges = 1 Housing)
2
6
45411S
Set Screw, M8 x 20, Zinc Plate
4
7
45137
Nut, M8, Nylock
4
8
45181
Grubscrew, M8 x 12, Socket Head
2
9
45151
M8 Light Flat Washer
8
8
4
1
QTY
2
1
3
7
7
6
9
4
6
5
9
5
7
Pt. No. 67381
Issue 0511
67
‘Renovator’ Seed Drill
11
13
8
8
16
1
13
11
Jockey Drive
10
11
2
25
27 28
26
5
10
6
4
27 28
21
31
20
29
19
30
17
9
12
25
32
7
4
3
22
23
24
18
33
9
68
14
15
‘Renovator’ Seed Drill
Jockey Drive
ITEM
PART No.
DESCRIPTION
QTY
1
25742
38T 1/2” P (25mm Bore) Sprocket
1
2
26352
13T/21T 1/2”P Crank Sprocket
1
3
25724
13T 1/2” P (20mm Bore) Sprocket
1
4
22294
6 x 6 x 25 Sprocket Key
3
5
26569
Drive Pedestal Shaft, Transfer
1
6
26568
Hexagonal Drive Shaft
1
7
25744
Jockey Wheel and Axle Assembly
1
8
43036
Drive Pedestal Transfer Shaft Bearing
2
9
17127
Jockey Wheel Axle Bearing
2
10
43386
“Y” Bearing
2
11
30359
3 Bolt Bearing Housing, PF52, (2 Flanges = 1 Housing)
2
12
25726
Jockey Drive Axle Spacer (where fitted)
1
13
25725
Jockey Arm Pivot Spacer
2
14
25739
Jockey Axle Inner Spacer
1
15
25727
Jockey Axle Outer Spacer (Loctite in place when fitted)
1
16
25729
Jockey Arm Pivot Outer Spacer (Loctite in place when fitted)
1
17
25735
Jockey Wheel Arm
1
18
25746
Jockey Drive Swing Guard
1
19
26567
Sensor Mount Bracket
1
20
43403
Sensor
1
21
43404
Magnet and Clamp
1
22
45401S
M6 x 16, Z/P Set Screw
2
23
45164
M6, Z/P Spring Washer
2
24
45156
M6, H/D Z/P Flat Washer
2
25
45180
M8 x 10 Socket Head Grubscrew
4
26
45181
M8 x 12 Socket Head Grubscrew
2
27
45411S
Set Screw, M8 x 20 Class 4.6, Zinc Plated
6
28
45137
M8, Nyloc Nut
6
29
45417S
M10 x 20 Class 4.6, Z/P Set Screw
1
30
45152
M10 Light Flat Washer
1
31
45138
M10 Nyloc Nut
1
32
47625
M16 Bellevilles Disc Washer
1
33
45140
M16 Nyloc Nut
1
69
Pt. No. 67381
Issue 0511
‘Renovator’ Seed Drill
Dual Gearbox Assembly
ITEM
PART No.
DESCRIPTION
1
25756
Gearbox Sub-Assembly
1
2
22036
Quadrant, Speed Adjusting
2
3
25754
Lever, Front, Speed Adjusting
1
4
25755
Lever, Rear, Speed Adjusting
1
5
43366
Tri-Knob, M8, Tapped Centre
2
6
47031
Bolt, Coach, M8 x 40 Cup Head, Class 4.6, Zinc Plated
2
7
45151
Washer, Flat, M8, Light
2
8
22041
Label, Front Box Speed Indicator (black writing on yellow background)
1
9
22042
Label, Rear Box Speed Indicator (yellow writing on black background)
1
10
44992s
Set Screw M8 x 20 Grade 8.8 Zinc Plate
2
11
44993s
SetScrew M8 x 25 Grade 8.8 Zinc Plate
6
12
45157
Washer, Flat, M8, Heavy Duty, Zinc Plate
2
13
45137
Nut, M8 Nyloc
8
14
25762
Gearbox Final Assembly (Includes items 1 to 13)
1
15
26359
13T/21T 1/2”P Change Sprocket (not illustrated)
1
16
22294
Sprocket Key (not illustrated)
1
17
45180
Grub Screw, M8 x 10 Socket Head (not illustrated)
2
2
QTY
1
12
13
10
2
11
8
7
9
5
3
11
10
6
11
70
11
4
‘Renovator’
Single Gearbox Assembly
ITEM
PART No.
1
25763
Single Output Gearbox Sub-Assembly
1
2
22036
Quadrant, Speed Adjusting
1
3
25755
Lever, Rear, Speed Adjusting
1
4
43366
Tri-Knob, M8, Tapped Centre
2
5
47031
Bolt, Coach, M8 x 40 Cup Head, Class 4.6, Zinc Plated
1
6
45151
Washer, Flat, M8, Light
1
7
22042
Label, Rear Box Speed Indicator (yellow writing on black background)
1
8
44992s
Set Screw M8 x 20 Grade 8.8 Zinc Plate
1
9
44993s
SetScrew M8 x 25 Grade 8.8 Zinc Plate
3
10
45157
Washer, Flat, M8, Heavy Duty, Zinc Plate
1
11
45137
Nut, M8 Nyloc
4
12
25764
Gearbox Final Assembly (Includes items 1 to 11)
1
13
26359
13T/21T 1/2”P Change Sprocket (not illustrated)
1
14
22294
Sprocket Key (not illustrated)
1
1
DESCRIPTION
11
10
QTY
8
9
3
2
7
5
6
11
9
4
Pt. No. 67381
Issue 0511
71
‘Renovator’ Seed Drill
Dual Seedbox Assembly
3
19
23
24 25
32 35 36
11
17
27
Lid Hinge Detail
8
12
16
7
10
18
4
5
32 34
31
35 36
35
16
33 35
13
Strut fasteners
on next page
20
21
27
22
14
15
30
28
29
19
9
6
72
Location Tab Detail
‘Renovator’ Seed Drill
Dual Seedbox Assembly
ITEM
PART No.
DESCRIPTION
QTY
1
Refer Table Below
Box Only
2
2
Refer Table Below
Box with Lid
2
3
Refer Table Below
Lid Only
2
4
22485P
Box Set Lifting Eye Profile
2
5
60116#
Box Set Mounting Bracket LH
1
6
60117#
Box Set Mounting Bracket RH
1
7
60118PH
Front Agitator Drive assy
1
8
60110PH
Rear Agitator Drive assy
1
9
22855#
Agitator Access Blanking Plate
2
10
10143
Front Box Quadrant Plate
1
11
10158
Rear Box Reverse Quadrant Plate
1
12
Refer Page 65
13
22419#
14
Seeder Assembly
32,40,42,48,56
Box Shaft Connecting Sleeve
2
Refer Table Below
Box Shaft (20mm)
2
15
Refer Table Below
Flap Shaft (18mm)
2
16
60096
Front Flapshaft Handle w/assy
2
17
60098
Rear Flapshaft Handle w/assy
2
18
22568
Location Tab (Calibration Tray)
6
19
Refer Table Below
Calibration Tray
4
20
45644
Gas Strut Mk4
4
21
43430
Lashing Hook
4
22
14442
Rubber Body Plug
28
23
29163
Hinge Assembly
6
24
22491
Hinge Pin
6
25
27599
Hinge Pin Spring Clip
6
26
43373
Black Edge Trim (Refer Table Below for Length per Box)
2
27
45019s
M12 x 30 Set Screw Class 8.8 Zinc Plate
20
28
45153
M12 Light Flat Washer
40
29
45139
M12 Nyloc Nut
20
30
45186
M10 x 12 Socket Head Grubscrew
4
31
45758
M6 x 16 Zinc Plated Countersunk Posidrive Screw
4
32
45908
M6 x 16 Zinc Plated Pan Head Machine Screw
21
33
45907
M6 x 12 Zinc Plated Pan Head Machine Screw
6
34
45122
M6 Class 8.8 Zinc Plated Hex Nut
5
35
45136
M6 Nylock Nut
26
36
45150
M6 Zinc Plated Light Flat Washer
12
Continued on following pages…
Pt. No. 67381
Issue 0511
73
‘Renovator’ Seed Drill
Dual Seedbox Assy (cont)
48
37
39
38
40
46
43
45
37
39
42
38
44
40
20
40
39
38
49
Gas Strut Fastener
Detail
Rubber Latch Detail
74
‘Renovator’ Seed Drill
Dual Seedbox Assy (cont)
ITEM
PART No.
DESCRIPTION
QTY
37
45005
M10x 40 Bolt Class 8.8 Zinc Plate (Gas Strut)
8
38
45158
M10 Heavy Duty Washer (Gas Strut)
16
39
45130
M10 Nut (Gas Strut)
8
40
45654
M10 Dome Nut Stainless
8
41
60190
Box Strap
2
42
45645
T Pull Rubber Rope
4
43
45646
Hook for Rubber Tensioner
4
44
45661ss
M10 x 50 SS Button Head Screw
4
45
45633
M4 x 25 Pan Head Screw
4
46
45632
M4 Nyloc Nut
4
47
Refer Table Below
Weather Skirts (Not Shown)
2
48
Refer Table Below
Transfer MK4 Renovator
4
49
60190P
Box Strap Bracket
2
50
43381
Metering Housing Outlet Cover
16R=10, 20R=8
PART NUMBER FOR DIFFERENT WIDTH MACHINES
ITEM
DESCRIPTION
16R/21R 3.0m
24R 3.0m
20R/24R 3.5m
28R 3.5m
1
Box Only
60251
60101
60401
60301
2
Box with Lid
60260
60261
60262
60263
3
Lid Only
60120
60120
60320
60320
14
Box Shaft (20mm)
60148
60148
60146
60146
15
Flap Shaft (18mm)
60147
60147
60145
60145
19
Calibration Trays
LONG 60140/ SHORT 60138
60130
60144
60144
47
Weather Skirt
60240
60240
60242
60242
48
Transfer MK4
45640
45640
45641
45641
Pt. No. 67381
Issue 0511
75
‘Renovator’ Seed Drill
Single Seedbox Assembly
3
Refer to previous page for
gas strut and rubber latch
parts and fasteners
34
15
8
1
27 31
10
15
4
Lid Hinge Detail
13
6
19
20
21
26
28 31
9
32
14
28 30
16
31 32
26
13
29
17
10
18
7
6
26
12
5
11
23 24 25
15
Location Tab Detail
76
‘Renovator’ Seed Drill
Single Seedbox Assembly
ITEM
PART No.
DESCRIPTION
QTY
1
Refer Table Below
Box Only
1
2
Refer Table Below
Box with Lid
1
3
Refer Table Below
Lid Only
1
4
25934
Box Set Mounting Bracket LH
1
5
25935
Box Set Mounting Bracket RH
1
6
60110PH
Rear Agitator Drive assy
1
7
22855#
Agitator Access Blanking Plate
1
8
10158
Rear Box Reverse Quadrant Plate
9
Refer Page 65
1
Seeder Assembly
16, 20, 21, 24, 28
10
22419#
Box Shaft Connecting Sleeve
1
11
Refer Table Below
Box Shaft (20mm)
1
12
Refer Table Below
Flap Shaft (18mm)
1
13
60098
Rear Flapshaft Handle w/assy
1
14
22568
15
Refer Table Below
Location Tab (Calibration Tray)
3
Calibration Tray
2
16
45644
Gas Strut Mk4
2
17
43430
Lashing Hook
2
18
14442
Rubber Body Plug
8
19
29163
Hinge Assembly
3
20
22491
Hinge Pin
3
21
27599
Hinge Pin Spring Clip
3
22
43373
Black Edge Trim
1
23
45019s
M12 x 30 Set Screw Class 8.8 Zinc Plate
8
24
45153
M12 Light Flat Washer
16
25
45139
M12 Nyloc Nut
8
26
45186
M10 x 12 Socket Head Grubscrew
2
27
45758
M6 x 16 Zinc Plated Countersunk Posidrive Screw
2
28
45908
M6 x 16 Zinc Plated Pan Head Machine Screw
11
29
45907
M6 x 12 Zinc Plated Pan Head Machine Screw
3
30
45122
M6 Class 8.8 Zinc Plated Hex Nut
3
31
45136
M6 Nylock Nut
14
32
45150
M6 Zinc Plated Light Flat Washer
12
33
Refer Table Below
Weather Skirt (Not Shown)
1
34
Refer Table Below
Transfer MK4 Renovator
2
35
43381
ITEM
DESCRIPTION
Metering Housing Outlet Cover
16R=5, 20R=4
PART NUMBER FOR DIFFERENT WIDTH MACHINES
169R/21R 3.0m
24R 3.0m
20R/24R 3.5m
28R 3.5m
1
Box Only
60251
60101
60401
60301
2
Box with Lid
60260
60261
60262
60263
3
Lid Only
60120
60120
60320
60320
14
Box Shaft (20mm)
60148
60148
60146
60146
15
Flap Shaft (18mm)
60147
60147
60145
60145
19
Calibration Trays
LONG 60130/ SHORT 60138
60130
60144
60144
33
Weather Skirt
60240
60240
60242
60242
34
Transfer Mk4
45640
45640
45641
45641
Pt. No. 67381
Issue 0511
77
‘Renovator’ Seed Drill
Agitator Drives
ITEM
PART No.
DESCRIPTION
1
60110PH
Agitator Drive Rear Housing complete with internals
1
2
60110
Rear Housing only
1
3
60118PH
Agitator Drive Front Housing complete with internals
1
4
60118
Front Housing only
1
5
22418
3/8” Pitch x 20mm Bore 21T Sprocket
2
6
22422
3/8” Pitch x 20mm Bore 15T Sprocket
2
7
22417
3/8” Pitch x 33 Link BS Chain
2
8
43396
3/8” Pitch Joiner Link
2
9
44968
M8 x 60 Class 8.8 Zinc Plated Bolt
2
10
44965
M8 x 45 Class 8.8 Zinc Plated Bolt
2
11
45137
M8 Nylock Nut
4
12
22425
Agitator Shaft Extension
2
13
22426
Seed Shaft Extension
2
14
43428
Nylon Bush
6
15
22416
Agitator Drive Spacer
2
16
22419
Box Shaft Connecting Sleeve
2
17
22420
Agitator Shaft Joining Collar
2
18
45180SS
M8 x 10 Stainless Steel Socket Head Grub Screw
4
19
44956SS
M6 x 40 Bolt S/Steel
4
20
45136SS
M6 Nyloc Nut S/Steel
4
21
45150SS
M6 Light Flat Washer
4
3
14
QTY
9 11
15
7
5
12
17
18
20
21
4
16
19
Rear assembly shown exploded
1
13
6
2
14
78
10 11
‘Renovator’ Seed Drill
ITEM
PART No.
1
Refer Below
2
Agitator Shaft Assembly
DESCRIPTION
QTY
Agitator Shaft Assembly
1
22420
16mm Agitator Joining Collar
2
3
22423
Agitator Shaft Support RH (Short)
2
4
22424
Agitator Shaft Support LH (Long)
2
5
22428
Agitator Shaft Support Cap
2
6
43442
5/8” Lurethane Wiper Seal
4
7
45185SS
M10 x 10 Stainless Steel Sockept Head Grubscrew
4
8
45410SSS
M8 x 16 Grade 316 Stainless Steel Set Screw
4
9
45137SS
M8 Grade 316 Stainless Steel Nylock Nut
4
10
47600
M30 ISO Fine Zinc Plated Hex Lock Nut
4
Drive End
Centre Bearing
8
10
2
7
4
6
Plain End
10
3
6
1
5
9
PART NUMBER FOR DIFFERENT WIDTH MACHINES
ITEM
DESCRIPTION
16R/21R 3.0m
24R 3.0m
20R/24R 3.5m
28R 3.5m
1
Agitator Shaft
60183
60181
60186
60184
Pt. No. 67381
Issue 0511
79
‘Renovator’ Seed Drill
Seeder Mechanism
ITEM
PART No.
DESCRIPTION
QTY
1
43375
Metering Housing
20 to 56
2
43376
Shutter Slide
20 to 56
3
43377
Seed Metering Wheel Assembly (Includes item 4)
20 to 56
4
43374
Fine Seed Wheel (For Spares Ordering Only)
5
43378
Bottom Flap & Bolt Assembly
20 to 56
6
22550
Seeder Extension Funnel
20 to 56
7
22551
Seed Diverter
20 to 56
8
22548
Spring Clip, S/S
20 to 56
9
43379
Seed Shaft Guide Bearing
6
10
43380
Guide Bearing Tension Spring
6
11
43382
Metering Wheel Clutch Hook
1
12
43383
Seed Rate Disc Calculator
1
13
43362
Fine Seed Wheel Brush (Optional Extra)
-
-
2
8
3
9
9
2
1
4
3
8
1
7
10
5
6
7
6
12
11
80
10
‘Renovator’ Seed Drill
DESCRIPTION
Hectaremeter Kit
ITEM
PART No.
QTY
1
43409
Hectaremeter Kit, (Includes items 2 to 7)
1
2
43400
Hectaremeter
1
3
43408
Manual, Hectaremeter
1
4
43404
Magnet and Clamp
1
5
43403
Sensor
1
6
43453
Hectaremeter Cable
1
7
43461
Cable, Recharging
1
8
43455
Electronic Scales
1
9
43456
Calculator
1
10
43457
Sealtop Plastic Container
1
2
Pt. No. 67381
Issue 0511
81
‘Renovator’ Seed Drill
3
4
23
24
Disc Opener 21, 24, 28R
22
3
4
27 28
7
21
25
29
18
9
29
5
20
37
25
21
8
26
33
19
6
9
17
19
18
32
35
37
15
14
36
16
28 10 33
11
12
13
30
34
82
32
‘Renovator’ Seed Drill
Disc Opener 21, 24, 28R
ITEM
PART No.
1
Refer Below
Disc Opener Complete
DESCRIPTION
QTY
1
2
Refer Below
Disc Opener Frame
1
3
60280
Pivot Arm
2
4
60287
Angle Bracket
2
5
60290
Frame Support
6
60460
Mounting Bracket
7
60452
Single Disc Assembly LH
9,11,13
8
60453
Single Disc Assembly RH
10,11,13
9
Refer Below
10
45650
2
20,23,27
Double Disc Assembly
1
Seal
21,24,28
11
60466
Housing
21,24,28
12
45652
Bearing
21,24,28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement