null  null
PPC-5190 Flat Panel PC
Page 1
PPC-5190 Flat Panel PC
REVISION HISTORY
Title
PPC-5190 Flat Panel PC User Manual
Revision Number
Description
Date of Issue
1.0
Initial release
November 2006
ABOUT THIS MANUAL
This document covers the description and installation instructions for the PPC-5190 flat
panel PC.
COPYRIGHT NOTICE
This document is copyrighted 2006, by IEI Technology Corp. All rights are reserved. IEI
Technology Corp. reserves the rights to alter the products described in this manual at any
time without prior notice.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Information provided in this manual is intended to be accurate and reliable. However, IEI
Technology Corp. assumes no responsibility for use of this manual, nor for any
infringements upon the rights of third parties, which may result from such use.
Page 2
PPC-5190 Flat Panel PC
SAFETY PRECAUTIONS
Prior to installing, moving, and modifying the panel PC, make sure the power
is turned off and the power cord is disconnected.
Do not apply voltage levels that exceed the specified voltage range. Doing
so will cause fire or an electrical shock.
Electric shocks can occur if the panel is opened. Do not drop or insert any
objects into the ventilation openings of the panel PC.
Only qualified engineers from certified system integrators or VARs are
allowed to make necessary functional modifications to the panel PC, e.g.,
adding a touch screen. IEI offers the customization service on a pre-order
basis.
For installations related to human safety, connect a separately installed
mechanical switch instead of the panel PC’s power switch.
Designs with stand-alone and fault-tolerant hardware considerations should
be implemented using the series models as a critical alarm or production line
control.
If considerable amount of dust, water, or fluids entered the panel PC, turn off
the power supply immediately, unplug the power cord, and contact the MPC
industrial panel PC vendor.
Explosions may occur with installations in environments where flammable
gases are present.
Fault-tolerant and failsafe designs should be implemented with the use of the
series models on transportation vehicles, ships, safety/security devices, or
medical devices not related to life-support functions. Users/integrators
should take the responsibility for implementations with adequate levels of
reliability and safety.
Preventive designs should be implemented so as to avoid the
communications faults between the panel PC and the
PC/workstation/terminals that controls it.
FURTHER PANEL PC PRECAUTIONS
Do not drop the panel PC against a hard surface. Doing so will damage the
display.
Do not strike or exert excessive force onto the touch panel.
Touching the touch panel using a sharp object will damage the LCD panel.
Page 3
PPC-5190 Flat Panel PC
Avoid environments exposed to direct sunlight, dust, or chemical vapors.
The panel PC is actively cooled. In no circumstances should the panel PC
operate with the openings obstructed by foreign objects. However, the
ambient temperature of the installation site should be observed and controlled
to avoid overheating the panel PC.
Condensation might form inside the panel PC chassis if exposed to sudden
changes in temperature.
Carefully route the power cord so that people cannot step on it. Do not place
anything over the power cord.
If the equipment should be left unused for an extended period of time,
disconnect it from the power source to avoid damage by transient
over-voltage.
If any of the following situations arises, get the equipment checked by service
personnel:
o
o
o
o
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work properly, or cannot be made to work
according to the user manual.
o
o
The equipment has been dropped and damaged.
The equipment shows obvious signs of breakage.
WARNING!
Any changes or modifications made to the equipment that are not
expressly approved by the relevant standards could void the authority to
operate the equipment.
Page 4
PPC-5190 Flat Panel PC
ADDITIONAL INFORMATION AND ASSISTANCE
Maintenance and Cleaning
Note the following precautions before starting to clean the panel PC.
When cleaning any single part or component of the computer, please read and understand
the details below fully.
Except for the properly installed front LCD panel, never spray or squirt liquids
directly onto any computer component. If the device needs to be cleaned,
please rub it with a piece of dry and soft cloth or a slightly moistened cloth with
the exterior casing.
The interior of the panel PC does not require cleaning. Keep fluids away
from the panel PC and the interior of it.
Be cautious of the tiny removable components when using a vacuum cleaner
to absorb the dirt on the floor.
Turn the system off before starting to clean up the panel PC.
Never drop any tiny objects through the openings of the panel PC or get
circuit board damp or wet.
Be cautious of all kinds of cleaning solvents or chemicals when usingt them
for the sake of cleaning. Some individuals may be allergic to the ingredients.
Avoid any food, drink or cigarette around the panel PC.
Cleaning Tools
Although many companies have created products to help improve the process of cleaning
Panel PCs and peripherals, users can also use household items to clean their computers
and peripherals. Below is a list of some items that may be needed or used when cleaning
the panel PC or panel PC peripherals.
Please keep in mind that some components in panel PC components may only be cleaned
using a product designed for cleaning that component, if this is the case it will be
mentioned in the cleaning tips.
Page 5
PPC-5190 Flat Panel PC
Cloth - A piece of cloth is the best tool to use when rubbing up a component.
Although paper towels or tissues can be used on most hardware as well, it is
still recommended that a piece of cloth is used to rub it.
Water or rubbing alcohol – Moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer.
Unknown solvents may be harmful to the plastics parts.
Vacuum cleaner - Absorb the dust, dirt, hair, cigarette particles, and other
particles out of a computer can be one of the best methods of cleaning a
computer. Over time these items can restrict the airflow in a computer and
cause circuitry to corrode.
Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas in the keyboard, mouse, and
other locations.
Foam swabs - Whenever possible it is better to use lint free swabs such as
foam swabs.
ESD PRECAUTIONS
Observe all conventional anti-ESD methods while handling the components contained
within the LCD should the need arise for adding a functionality. The use of a grounded
wrist strap and an anti-static work pad is recommended. Avoid dust and debris or other
static-accumulating materials in the work area.
Page 6
PPC-5190 Flat Panel PC
CONVENTIONS USED IN THIS MANUAL
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text in italics. The italicized text is the warning message.
CAUTION!
Cautionary messages should also be heeded to helps reduce the chance of losing data or
damaging the system. Cautions are easy to recognize. The word “caution” is written as
“CAUTION,” both capitalized and bold and is followed by text in italics. The italicized text is
the cautionary message.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
helps avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text in italics. The italicized text is the
cautionary message.
Lists
Bulleted Lists: Bulleted lists are statements of non-sequential facts that can be read in
any order. Each statement is preceded by a black square “■” or bullets in other shapes.
Numbered Lists: Numbered lists describe sequential steps should be followed in order.
Page 7
PPC-5190 Flat Panel PC
Table of Contents
1
INTRODUCTION................................................................................................... 19
1.1 PPC-5190 FLAT PANEL PC OVERVIEW .................................................................... 20
1.1.1 PPC-5190 Model Variation.............................................................................. 20
1.1.2 PPC-5190 Flat Panel PC Applications ........................................................... 20
1.1.3 PPC-5190 Flat Panel PC Features.................................................................. 21
1.2 PPC-5190 EXTERNAL OVERVIEW ............................................................................ 21
1.2.1 General Description......................................................................................... 21
1.2.2 Front Panel ...................................................................................................... 21
1.2.3 Rear Panel ....................................................................................................... 22
1.2.4 Top Panel ......................................................................................................... 23
1.2.5 PPC-5190 Bottom Panel.................................................................................. 23
1.2.6 Left Panel ......................................................................................................... 24
1.2.7 Right Panel....................................................................................................... 25
1.3 PPC-5190 INTERNAL OVERVIEW ............................................................................. 25
1.4 PPC-5190 SPECIFICATIONS ...................................................................................... 26
1.4.1 Preinstalled Hardware Components ................................................................ 26
1.4.2 System Specifications ....................................................................................... 26
1.4.3 PPC-5190 Motherboard Specifications ........................................................... 28
1.4.4 Flat Panel Screen............................................................................................. 29
1.4.5 Power Supply ................................................................................................... 30
1.4.5.1 ACE-4518AP Power Supply..................................................................... 31
1.4.5.2 ACE-4520C Power Supply ....................................................................... 32
1.5 DIMENSIONS ............................................................................................................ 33
2
POS-8520 MOTHERBOARD................................................................................ 35
2.1 INTRODUCTION ........................................................................................................ 36
2.2 CPU SUPPORT.......................................................................................................... 36
2.3 ON-BOARD CHIPSETS ............................................................................................... 36
2.3.1 Northbridge and Southbridge Chipsets ........................................................... 36
2.3.2 852GME Northbridge Chipset......................................................................... 36
Page 8
PPC-5190 Flat Panel PC
2.3.3 ICH5 Southbridge Chipset............................................................................... 37
2.4 GRAPHICS SUPPORT ................................................................................................. 38
2.5 PERIPHERAL DEVICE INTERFACES, CONNECTORS, AND SLOTS ................................. 40
2.5.1 OEM Options ................................................................................................... 40
2.5.2 Internal Slots.................................................................................................... 40
2.5.3 Internal Peripheral Device Connectors........................................................... 40
2.5.4 External Peripheral Device Connectors.......................................................... 42
3
INSTALLATION AND CONFIGURATION ....................................................... 43
3.1 INSTALLATION PRECAUTIONS ................................................................................... 44
3.2 PREINSTALLED COMPONENTS .................................................................................. 44
3.3 INSTALLATION AND CONFIGURATION STEPS ............................................................. 45
3.4 UNPACKING.............................................................................................................. 45
3.4.1 Packing List ..................................................................................................... 46
3.5 JUMPER SETTINGS .................................................................................................... 46
3.5.1 Remove the Back Cover ................................................................................... 48
3.5.2 CF Card Setup (JP12)...................................................................................... 49
3.5.3 Clear CMOS Setup (JP1)................................................................................. 49
3.5.4 COM2 Port RS232/422/485 Selection (JP10, JP20) ....................................... 50
3.5.5 COM port RI and Voltage Selection................................................................. 50
3.5.6 Keyboard and Mouse Power Source Setting (JP18)........................................ 52
3.5.7 LCD Voltage Setup (JP2) ................................................................................. 52
3.6 HDD, FDD AND CD DRIVE INSTALLATION ............................................................. 53
3.6.1 HDD Installation ............................................................................................. 53
3.6.2 FDD Installation.............................................................................................. 54
3.6.3 CD Drive Installation ...................................................................................... 55
3.7 MOUNTING THE SYSTEM .......................................................................................... 59
3.7.1 Wall Mounting.................................................................................................. 59
3.7.2 Panel/ Mounting............................................................................................... 62
3.7.3 Rack and Cabinet Installation ......................................................................... 64
3.7.4 Arm Mounting .................................................................................................. 65
3.8 EXTERNAL PERIPHERAL INTERFACE CONNECTORS .................................................. 66
3.8.1 LCD Panel Connection .................................................................................... 66
3.8.2 Ethernet Connection ........................................................................................ 66
3.8.3 USB Connection............................................................................................... 67
Page 9
PPC-5190 Flat Panel PC
3.8.4 Keyboard and Mouse Connection.................................................................... 67
3.8.5 Parallel Port Connection................................................................................. 67
3.8.6 Serial Port Connection .................................................................................... 67
3.8.7 Audio Port Connection..................................................................................... 67
4
SYSTEM MAINTENANCE .................................................................................. 69
4.1 SYSTEM MAINTENANCE INTRODUCTION .................................................................. 70
4.2 MOTHERBOARD REPLACEMENT ............................................................................... 70
4.3 BACK COVER REMOVAL AND ELEVATED PLATFORM DETACHMENT ......................... 70
4.3.1 Back Cover Removal........................................................................................ 71
4.3.2 Detaching the Elevated Platform..................................................................... 72
4.4 DIMM REPLACEMENT............................................................................................. 74
4.5 PSU MODULE REPLACEMENT.................................................................................. 75
4.5.1 Remove the Old PSU........................................................................................ 75
4.5.2 Install the New PSU ......................................................................................... 77
4.6 SYSTEM COOLING FAN REPLACEMENT .................................................................... 78
4.6.1 Remove the Old System Cooling Fans ............................................................. 78
4.6.2 Install the New System Cooling Fans .............................................................. 79
5
AMI BIOS................................................................................................................ 81
5.1 INTRODUCTION ........................................................................................................ 82
5.1.1 Starting Setup................................................................................................... 82
5.1.2 Using Setup ...................................................................................................... 82
5.1.3 Getting Help..................................................................................................... 83
5.1.4 Unable to Reboot After Configuration Changes.............................................. 83
5.1.5 BIOS Menu Bar................................................................................................ 83
5.2 MAIN ....................................................................................................................... 84
5.3 ADVANCED ............................................................................................................... 85
5.3.1 CPU Configuration.......................................................................................... 87
5.3.2 IDE Configuration ........................................................................................... 89
5.3.2.1 IDE Master, IDE Slave ............................................................................. 93
5.3.3 Floppy Configuration....................................................................................... 97
5.3.4 Super IO Configuration.................................................................................... 98
5.3.5 Hardware Health Configuration.................................................................... 104
5.3.6 ACPI Configuration ....................................................................................... 106
Page 10
PPC-5190 Flat Panel PC
5.3.6.1 General ACPI Configuration................................................................... 107
5.3.6.2 Advanced ACPI Configuration ............................................................... 108
5.3.7 MPS Configuration ......................................................................................... 111
5.3.8 Remote Access Configuration .........................................................................112
5.3.9 USB Configuration..........................................................................................113
5.4 PCI/PNP .................................................................................................................115
5.5 BOOT ..................................................................................................................... 120
5.5.1 Boot Settings Configuration........................................................................... 121
5.5.2 Boot Device Priority ...................................................................................... 123
5.5.3 Removable Drives .......................................................................................... 124
5.6 SECURITY............................................................................................................... 125
5.7 CHIPSET ................................................................................................................. 126
5.7.1 NorthBridge Configuration............................................................................ 127
5.7.2 SouthBridge Configuration............................................................................ 131
5.8 POWER ................................................................................................................... 132
5.9 EXIT ....................................................................................................................... 137
A
IEI PANEL PC PRODUCT LINE ....................................................................... 139
A.1 IEI PANEL PC PRODUCTS ...................................................................................... 140
A.1.1 Overview........................................................................................................ 140
A.1.2 IEI Panel PC Product Series ......................................................................... 140
A.2 PANEL PC PRODUCT SOLUTIONS ........................................................................... 140
A.2.1 PPC-27 Series Panel PC Solutions ............................................................... 140
A.2.2 PPC-37 Series Panel PC Solutions ............................................................... 141
A.2.3 PPC-51 Series Panel PC Solutions ............................................................... 143
A.2.4 PPC-52 Series Panel PC Solutions ............................................................... 145
A.2.5 PPC-53 Series Panel PC Solutions ............................................................... 146
B
INTERFACE CONNECTORS ............................................................................ 149
B.1 FLOPPY DISK DRIVE CONNECTOR ......................................................................... 150
B.2 PCIE - IDE DISK DRIVE CONNECTOR ................................................................... 151
B.3 PARALLEL PORT..................................................................................................... 152
B.4 SERIAL PORTS........................................................................................................ 153
B.5 KEYBOARD / MOUSE CONNECTOR ........................................................................ 158
B.6 EXTERNAL SWITCHES AND INDICATORS ................................................................ 159
Page 11
PPC-5190 Flat Panel PC
B.7 USB PORT CONNECTOR ........................................................................................ 160
B.8 IRDA INFRARED INTERFACE PORT ........................................................................ 161
B.9 VGA CONNECTOR ................................................................................................. 162
B.10 LAN RJ45 CONNECTOR...................................................................................... 163
B.11 FAN CONNECTOR ................................................................................................. 163
B.12 INVERTER (LCD BACKLIGHT) CONNECTOR ........................................................ 164
B.13 LCD PANEL LVDS INTERFACE CONNECTOR ....................................................... 165
B.14 AUDIO CONNECTORS ........................................................................................... 165
B.15 DIGITAL INPUT / OUTPUT .................................................................................... 166
B.16 COMPACT FLASH TYPE II STORAGE CARD SOCKET ........................................... 167
B.17 ATX POWER CONNECTOR ................................................................................... 168
B.18 ATX 12V POWER CONNECTOR ........................................................................... 168
B.19 INTERNAL SWITCHES AND INDICATORS................................................................ 169
B.20 SERIAL ATA CONNECTOR .................................................................................... 169
C
BIOS CONFIGURATION OPTIONS ................................................................ 171
C.1 BIOS CONFIGURATION OPTIONS ........................................................................... 172
D
SOFTWARE DRIVERS ....................................................................................... 177
D.1 INTRODUCTION ..................................................................................................... 178
D.2 DRIVER INSTALLATION .......................................................................................... 178
D.3 TOUCH PANEL DRIVER CONFIGURATION ............................................................... 185
INDEX............................................................................................................................ 187
Page 12
PPC-5190 Flat Panel PC
List of Figures
Figure 1-1: PPC-5190 Front View .................................................................................22
Figure 1-2: PPC-5190 Rear View..................................................................................23
Figure 1-3: PPC-5190 Top View ...................................................................................23
Figure 1-4: Bottom View................................................................................................24
Figure 1-5: Left View .....................................................................................................25
Figure 1-6: Right View...................................................................................................25
Figure 1-7: Internal Components ..................................................................................26
Figure 1-8: Dimensions (units in mm) ...........................................................................33
Figure 3-1: Back Cover Retention Screws ....................................................................48
Figure 3-2: HDD Retention Screws...............................................................................53
Figure 3-3: FDD Retention Screws ...............................................................................54
Figure 3-4: FDD Adapter and FDD Bracket Installation................................................55
Figure 3-5: CD Drive Adapter Installation .....................................................................56
Figure 3-6: CD Drive Retention Screws ........................................................................56
Figure 3-7: Remove CD Drive.......................................................................................57
Figure 3-8: CD Drive Blank Plate Assembly .................................................................57
Figure 3-9: CD Drive Blank Plate Assembly .................................................................58
Figure 3-10: CD Drive Installed.....................................................................................59
Figure 3-11: Wall-mounting Bracket..............................................................................60
Figure 3-12: Mount the Chassis ....................................................................................61
Figure 3-13: Secure the Chassis...................................................................................62
Figure 3-14: Cut the Panel ............................................................................................63
Figure 3-15: Panel Mounting Clamp Positions..............................................................63
Figure 3-16: Tighten the Panel Mounting Clamp Screws .............................................64
Figure 3-17: Rack Mounting..........................................................................................65
Figure 3-18: Arm Mount Retention Screw Holes ..........................................................66
Figure 4-1: Rear Cover Retention Screws (Real Panel) ...............................................72
Figure 4-2: CD Drive Retention Screws ........................................................................73
Page 13
PPC-5190 Flat Panel PC
Figure 4-3: Internal Elevated Platform Retention Screws .............................................73
Figure 4-4: Elevated Platform Retention Screws (Top Panel) ......................................73
Figure 4-5: Elevated Platform Retention Screws (Right Panel) ....................................74
Figure 4-6: Elevated Platform Retention Screws (Bottom Panel).................................74
Figure 4-7: Elevated Platform Retention Screws (PCI Riser Card) ..............................74
Figure 4-8: DIMM Socket Clip Locations.......................................................................75
Figure 4-9: PSU Motherboard Connectors ...................................................................76
Figure 4-10: PSU Bottom Panel Retention Screws ......................................................76
Figure 4-11: PSU Bracket to Chassis Retention Screws ..............................................77
Figure 4-12: PSU Bracket Retention Screws................................................................77
Figure 4-13: System Cooling Fans Motherboard Connector ........................................78
Figure 4-14: System Cooling Fans Left Panel Retention Screws.................................79
Page 14
PPC-5190 Flat Panel PC
List of Tables
Table 1-1: PPC-5190 Model Variation ..........................................................................20
Table 1-2: PPC-5190 Specifications .............................................................................28
Table 1-3: Motherboard Specifications .........................................................................29
Table 1-4: 19” TFT LCD Monitor Specifications............................................................30
Table 1-5: ACE-4518AP Power Supply Specifications .................................................32
Table 1-6: ACE-4520C Power Supply Specifications ...................................................33
Table 3-1: Onboard Jumpers ........................................................................................47
Table 3-2: CF Card Setup Jumper Settings..................................................................49
Table 3-3: Clear CMOS Jumper Settings......................................................................49
Table 3-4: COM2 Port Jumper Settings ........................................................................50
Table 3-5: COM1 RI and Voltage Selection Jumper.....................................................50
Table 3-6: COM1 RI Voltage Selection Jumper............................................................50
Table 3-7: COM2 RI and Voltage Selection Jumper.....................................................51
Table 3-8: COM2 RI Voltage Selection Jumper............................................................51
Table 3-9: COM3 RI and Voltage Selection Jumper.....................................................51
Table 3-10: COM3 RI Voltage Selection Jumper..........................................................51
Table 3-11: COM4 RI and Voltage Selection Jumper...................................................51
Table 3-12: COM4 RI Voltage Selection Jumper..........................................................52
Table 3-13: Keyboard and Mouse Power Source Setting.............................................52
Table 3-14: LCD Voltage Setup Jumper Settings .........................................................52
Table 5-1: BIOS Navigation Keys .................................................................................83
Page 15
PPC-5190 Flat Panel PC
List of BIOS Menus
BIOS Menu 1: Main .......................................................................................................84
BIOS Menu 2: Advanced...............................................................................................86
BIOS Menu 3: CPU Configuration.................................................................................87
BIOS Menu 4: IDE Configuration ..................................................................................89
BIOS Menu 5: IDE Master and IDE Slave Configuration ..............................................93
BIOS Menu 6: Floppy Configuration .............................................................................97
BIOS Menu 7: Super IO Configuration..........................................................................98
BIOS Menu 8: Hardware Health Configuration .......................................................... 104
BIOS Menu 9: ACPI Configuration............................................................................. 106
BIOS Menu 10: General ACPI Configuration............................................................. 107
BIOS Menu 11: Advanced ACPI Configuration.......................................................... 108
BIOS Menu 12: MPS Configuration ........................................................................... 111
BIOS Menu 13: USB Configuration............................................................................ 113
BIOS Menu 14: PCI/PnP Configuration ..................................................................... 115
BIOS Menu 15: Boot .................................................................................................. 120
BIOS Menu 16: Boot Settings Configuration.............................................................. 121
BIOS Menu 17: Boot Device Priority Setting.............................................................. 123
BIOS Menu 18: Removable Drives ............................................................................ 124
BIOS Menu 19: Security............................................................................................. 125
BIOS Menu 20: Chipset.............................................................................................. 126
BIOS Menu 21: NorthBridge Chipset Configuration................................................... 127
BIOS Menu 22: SouthBridge Chipset Configuration .................................................. 131
BIOS Menu 23: Power................................................................................................ 132
BIOS Menu 24:Exit..................................................................................................... 137
Page 16
PPC-5190 Flat Panel PC
Glossary
AC ’97
Audio Codec 97
HDD
Hard Disk Drive
ACPI
Advanced Configuration and
IDE
Integrated Data Electronics
Power Interface
I/O
Input/Output
APM
Advanced Power Management
ICH4
I/O Controller Hub 4
ARMD
ATAPI Removable Media Device
L1 Cache Level 1 Cache
ASKIR
Shift Keyed Infrared
L2 Cache Level 2 Cache
ATA
Advanced Technology
LCD
Liquid Crystal Display
Attachments
LPT
Parallel Port Connector
BIOS
Basic Input/Output System
LVDS
Low Voltage Differential Signaling
CFII
Compact Flash Type 2
MAC
Media Access Controller
CMOS
Complementary Metal Oxide
OS
Operating System
Semiconductor
PCI
Peripheral Connect Interface
CPU
Central Processing Unit
PIO
Programmed Input Output
Codec
Compressor/Decompressor
PnP
Plug and Play
COM
Serial Port
POST
Power On Self Test
DAC
Digital to Analog Converter
RAM
Random Access Memory
DDR
Double Data Rate
SATA
Serial ATA
DIMM
Dual Inline Memory Module
S.M.A.R.T Self Monitoring Analysis and
DIO
Digital Input/Output
DMA
Direct Memory Access
SPD
Serial Presence Detect
EIDE
Enhanced IDE
S/PDI
Sony/Philips Digital Interface
EIST
Enhanced Intel SpeedStep
SDRAM
Synchronous Dynamic Random
Reporting Technology
Access Memory
Technology
FDD
Floppy Disk Drive
SIR
Serial Infrared
FDC
Floppy Disk Connector
UART
Universal Asynchronous
FFIO
Flexible File Input/Output
FIFO
First In/First Out
USB
Universal Serial Bus
FSB
Front Side Bus
VGA
Video Graphics Adapter
IrDA
Infrared Data Association
Receiver-transmitter
Page 17
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 18
PPC-5190 Flat Panel PC
Chapter
1
1 Introduction
Page 19
PPC-5190 Flat Panel PC
1.1 PPC-5190 Flat Panel PC Overview
The PPC-5190 flat panel PC is a flexible, multi-functional flat panel PC that can be applied
in diverse operational environments and implemented in multi-faceted applications. The
PPC-5190 comes fully kitted with a high-performance motherboard, CPU, power supply
unit and a host of other peripheral interface connectors. The PPC-5190 is designed for
ease of use and easy installation.
1.1.1 PPC-5190 Model Variation
Four IEI PPC-5190 models are available. The models are listed in Table 1-1.
Touch
Model
CPU
Socket
Power
Screen
Intel© Pentium© 4
PPC-5190GS/8520/ACE-4518AP
478
AC Input
No
478
AC Input
Yes
478
DC Input
No
478
DC Input
Yes
Intel© Celeron© D
Intel© Pentium© 4
PPC-5190GS/8520/ACE-4518AP/T-R
Intel© Celeron© D
Intel© Pentium© 4
PPC-5190GS/8520/ACE-4520C
Intel© Celeron© D
Intel© Pentium© 4
PPC-5190GS/8520/ACE-4520C/T-R
Intel© Celeron© D
Table 1-1: PPC-5190 Model Variation
1.1.2 PPC-5190 Flat Panel PC Applications
The PPC-5190 flat panel PC is designed for rigorous industrial environments where it may
be exposed to both heat and moisture. Its durability and strength also makes it an ideal
choice for public access computers. Some possible applications include:
Automated manufacturing processes
Public information gathering point
Page 20
PPC-5190 Flat Panel PC
1.1.3 PPC-5190 Flat Panel PC Features
Some of the features of the PPC-5190 flat panel PC include:
Mainstream panel PC design with dual display function.
Aluminum die-casting front panel meet IP 65 water proof standard
High performance Intel Pentium 4 / Celeron CPU support
Dual DDR memory DIMM support up to 2GB SDRAM
Serial ATA-150 connections
High brightness 19” industrial grade panel
Fully I/O function support:
o
o
o
o
5 x COM (1 for Touch Screen)
6 x USB 2.0 ports
1 x PCI slot
1 x CF socket
Dual 10/100/Gigabit Ethernet supported
RoHS compliant
1.2 PPC-5190 External Overview
1.2.1 General Description
The PPC-5190 flat panel PC is comprised of an LCD screen, aluminum front panel and
heavy duty steel rear and side panels. The rear panel provides screw holes for wall and an
arm mounting. The right panel provides access to a slim type CD drive bay and a floppy
disk drive bay. The bottom panel provides access to external interface connectors that
include GbE, USB 2.0, audio, parallel port, serial port connectors and a CF card slot.
1.2.2 Front Panel
The front panel of the PPC-5190 (Figure 1-1) is a flat panel 19” TFT LCD screen
surrounded by an aluminum frame.
Page 21
PPC-5190 Flat Panel PC
Figure 1-1: PPC-5190 Front View
1.2.3 Rear Panel
The rear panel has a fan vent, four VESA standard mounting holes and several retention
screw holes. The VESA mounting holes are circled in Figure 1-2.
Page 22
PPC-5190 Flat Panel PC
Figure 1-2: PPC-5190 Rear View
1.2.4 Top Panel
The top panel has two fan vents, eight mounting clamp slots and three retention screws for
securing the drive bay bracket. The retention screws are circled in Figure 1-3 below.
Figure 1-3: PPC-5190 Top View
1.2.5 PPC-5190 Bottom Panel
The bottom panel shown in Figure 1-4 has the following interfaces:
Page 23
PPC-5190 Flat Panel PC
1 x Power input connector
1 x Power switch
6 x USB connectors
1 x Reset button
2 x RJ-45 GbE connectors
2 x PS/2 keyboard/mouse connector
5 x Serial port (COM) connectors
1 x PCI add-on card slot
1 x Parallel port connector
3 x Audio jacks
1 x VGA connector
1 x Compact Flash slot
Figure 1-4: Bottom View
1.2.6 Left Panel
The left side panel has two fan vents and four retention screws for securing the two
internal fans. The retention screws are circled in Figure 1-5.
Page 24
PPC-5190 Flat Panel PC
Figure 1-5: Left View
1.2.7 Right Panel
The right side panel provides access to a slim type CD drive bay and a FDD drive bay
shown in Figure 1-6.
Figure 1-6: Right View
1.3 PPC-5190 Internal Overview
The PPC-5190 internal components are configured in three levels. An elevated platform
on the right side of the chassis supports a HDD, a CD drive and a FDD. On the second
level, below the elevated platform, are a motherboard and a PSU module. The
motherboard and the PSU module are installed on a metal sheet that protects the rear of
the 19” TFT LCD screen. Below the metal sheet is a circuit board that is connected to the
screen and the motherboard. The three levels of components can be seen in Figure 1-7.
Page 25
PPC-5190 Flat Panel PC
Figure 1-7: Internal Components
1.4 PPC-5190 Specifications
1.4.1 Preinstalled Hardware Components
The PPC-5190 flat panel PC has the following preinstalled components:
1 x Motherboard
1 x 19” TFT LCD screen
1 x Power supply
2 x Cooling fans
The technical specifications for these components and the system are shown in the
sections below.
1.4.2 System Specifications
The technical specifications for the PPC-5190 system are listed in Table 1-2.
SPECIFICATION
DESCRIPTION
Front Panel
Aluminum Front Panel meets IP 65 standard
Chassis
Heavy-duty Steel
LCD Panel
19” High luminance TFT LCD
Resolution
1280 x 1024 (SXGA)
Page 26
PPC-5190 Flat Panel PC
Brightness
300 cd/m2
Contrast Ratio
700:1
LCD MTBF
50,000 hrs
Backlight MTBF
50,000 hrs
Viewing Angle (H/V)
140/130
Optional 5-wire resistive type touch screen
Touch Screen
with RS-232 interface
Display
Supports Dual Display
Add-On Card (Optional)
Support PCI and CFII
One 2.5” HDD bay with anti-shock
Drive Bay
One slim type CD drive bay
One slim type FDD bay
Input voltage: 90~265V AC, 50~60 Hz
Output rating: 180W
Output voltage: [email protected]
Power Supply
[email protected]
[email protected]
[email protected]
[email protected]
Page 27
PPC-5190 Flat Panel PC
Input voltage: 24VDC (18-36VDC)
Output rating: 200W
Output voltage: [email protected]
[email protected]
[email protected]
[email protected]
[email protected]
Mounting Feature
Panel, Arm, Wall, or Rack/Cabinet
Color
Silver (PANTONE PMS-8001)
Operating Temperature
0~50˚C
Relative Humidity
5 ~ 85%, non-condensing
5 - 17Hz, 0.1” double amplitude displacement
Vibration
17 - 640Hz, 1.5G acceleration, peak to peak
Shock
10G Acceleration, peak to peak (11ms)
Dimensions
482.6(W) x 399.3(H) x 115.2(D) mm
Net/Gross Weight
12.6/18.2 Kg
Environment
RoHS Compliant
Table 1-2: PPC-5190 Specifications
1.4.3 PPC-5190 Motherboard Specifications
The PPC-5190 comes with a POS-8520 motherboard. The technical specifications of the
motherboard are listed in Table 1-3.
SPECIFICATION
DESCRIPTION
CPU
Socket-478 base Intel Pentium 4 / Celeron D
Northbridge
852GME
Page 28
PPC-5190 Flat Panel PC
Southbridge
ICH5
Max. FSB
533 MHz
Memory
2 x DDR 266/333 DIMM socket up to 2GB
BIOS
AMI BIOS Label
CRT integrated in Intel 852GME
Display
LVDS Dual 18-bit TTL LCD integrated in Intel 852GM
1 x PCI slot
Expansion Interface
1 x CFII
Audio
AC' 97 Codec
Ethernet
2 x Realtek RTL8110SC GbE controller
1 x RS-232/422/485 port
COM
5 x RS-232 ports (1 for optional touch screen)
USB 2.0
6 x USB 2.0 ports
Drive Interfaces
2 x SATA drive connectors
LPT
2 x ATA 100 channels
KB/ MS
2 x PS/2 connector
IrDA
1 x IrDA interface
Table 1-3: Motherboard Specifications
1.4.4 Flat Panel Screen
The PPC-5190 comes with a 19” TFT LCD monitor at the front of the flat panel PC
(Figure 1-1). The specifications for the LCD monitor are shown in Table 1-4 below.
SPECIFICATION
DESCRIPTION
Model
AUO-M190EG02
Page 29
PPC-5190 Flat Panel PC
Size
19”
Resolution
SXGA (1280 x 1024)
Active Area (mm)
376.32 x 301.06
Pixel Pitch (mm)
0.294
Mode
TN
Number of Colors
16.2M
Color Saturation (%)
72
View Angel (H/V)
160 / 160
Brightness (cd/m2)
300
Contrast Ratio
700 : 1
Response Time (ms) (at 25°C)
6
Power Consumption (W)
28
Interface
2ch LVDS
Supply Voltage (V)
5
Backlight
4 CCFL
Outline Dimensions (mm)
396.0 x 324.0 x 17.5
Weight (g)
2500
Table 1-4: 19” TFT LCD Monitor Specifications
1.4.5 Power Supply
The PPC-5190 flat panel PC comes with either an ACE-4518AP 180W AC-DC 1U, or
ACE-4520C 200W DC 1U RoHS compliant ATX power supply. The PSUs have an MTBF
greater than 100,000 hours.
Page 30
PPC-5190 Flat Panel PC
WARNING:
Under no circumstances is the PSU case to be opened. The PSU
module is not user serviceable and there are dangerous high-voltages
inside the case. If there are any problems with the PSU module, please
contact the dealer or reseller immediately.
1.4.5.1 ACE-4518AP Power Supply
Specifications for the ACE-4518AP PSU module are shown in (Table 1-5).
Voltage
AC90V ~ 265VAC Full Range
Frequency
47 ~ 63Hz
Input Current
4A(RMS)@115VAC
INPUT
2A(RMS)@230VAC
Inrush Current
50A Max for 115VAC
80A Max for 230VAC
Voltage (V)
+3.3V
+5V
+12V
-12V
5VSB
Min. Load (A)
0.3A
0.3A
1.5A
0A
0A
Max. Load (A)
16.8A
12A
10A
0.8A
2A
Ripple and Noise (mV)
50mV
50mV
120mV
120mV
50mV
OUTPUT
+3.3V & +5V≦61W
+3.3V & +5V & +12V≦160W
GENERAL
Watt
180W
PFC
Active
Hold-up time
17ms minimum
Efficiency
68%
MTBF
100,000hrs
Page 31
PPC-5190 Flat Panel PC
Temperature
0~50°C (Operating)
-20~80°C (Storage)
Humidity
5 –95% RH, Non-condensing
(Operating & Storage)
Dimension
150mm (W) x 81.5mm (H) x 40.5mm (D)
Table 1-5: ACE-4518AP Power Supply Specifications
1.4.5.2 ACE-4520C Power Supply
Specifications for the ACE-4520C PSU module are shown in (Table 1-6).
INPUT
OUTPUT
Voltage
18VDC ~ 36VDC Full Range
Input Current
15A
Inrush Current
100A
Voltage (V)
+3.3V
+5V
+12V
-12V
5VSB
Min. Load (A)
0.0A
1.0A
0.5A
0.0A
0.0A
Max. Load (A)
12A
12A
15.4A
0.5A
2.0A
Ripple and Noise (mV)
50mV
50mV
120mV
120mV
50mV
+3.3V & +5V≦80W; +3.3V & +5V & +12V≦184W
GENERAL
Watt
200W
PFC
Active
Hold-up time
20ms minimum
Efficiency
78%
MTBF
100,000hrs
Temperature
0~50°C (Operating); -20~80°C (Storage)
Humidity
5 –95% RH, Non-condensing (Operating & Storage)
Dimension
150mm (W) x 81.5mm (H) x 40.3mm (D)
Table 1-6: ACE-4520C Power Supply Specifications
Page 32
PPC-5190 Flat Panel PC
1.5 Dimensions
The dimensions of the PPC-5190 flat panel PC are shown in Figure 1-8 below.
Figure 1-8: Dimensions (units in mm)
Page 33
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 34
PPC-5190 Flat Panel PC
Chapter
2
2 POS-8520
Motherboard
Page 35
PPC-5190 Flat Panel PC
2.1 Introduction
The PPC-5190 flat screen PC contains a POS-8520 motherboard. The motherboard is the
heart of any computer and is responsible for transmitting, receiving and processing data
as well as driving the different on-board devices. This chapter gives a brief introduction to
the POS-8520 motherboard. For more complete details on the connectors and the
different implementations of the POS-8520, please refer to the POS-8520 user manual.
2.2 CPU Support
The POS-8520 installed in the PPC-5190 supports socket 478, Intel Pentium 4/Celeron D
FSB 533 MHz CPU.
2.3 On-board Chipsets
2.3.1 Northbridge and Southbridge Chipsets
The following chipsets are preinstalled on the board:
Northbridge: Intel 852GME
Southbridge: ICH5
The following two sections (Section 2.3.2 and Section 2.3.3) list some of the features of
the 852GME and the ICH5 chipsets. For more information on these two chipsets please
refer to the Intel website.
2.3.2 852GME Northbridge Chipset
The 852GME northbridge chipset comes with the following features:
Supports the Intel Pentium 4 processor and Intel Celeron processor with Intel
NetBurst® microarchitecture
400 MHz or 533 MHz system bus delivers a high-bandwidth connection
between the processor and the platform
Integrated graphics utilizing Intel® Extreme Graphics 2 technology
AGP 4X support
Page 36
PPC-5190 Flat Panel PC
Display
o
o
o
o
Analog display support
Dual independent pipe support
DVO (DVOB and DVOC) support
Dedicated Local Flat Panel (LFP) LVDS interface
Intel® Embedded Graphics Drivers
o
o
o
o
Graphics interface support
Multi-monitor support
Dynamic display-mode support
Embedded video BIOS
2.3.3 ICH5 Southbridge Chipset
The ICH5 southbridge chipset comes with the following features:
PCI Bus Interface
o
o
o
New: Supports PCI Revision 2.3 Specification at 33 MHz
6 available PCI REQ/GNT pairs
One PCI REQ/GNT pair can be given higher arbitration priority (intended
for external 1394 host controller)
o
Support for 44-bit addressing on PCI using DAC protocol
Integrated LAN Controller
o
o
o
o
Integrated ASF Management Controller
WfM 2.0 and IEEE 802.3 Compliant
LAN Connect Interface (LCI)
10/100 Mbit/sec Ethernet Support
Integrated Serial ATA Host Controllers
o
o
o
Independent DMA operation on two ports.
Data transfer rates up to 1.5 Gb/s (150 MB/s).
RAID Level 0 Support (ICH5R Only)
Integrated IDE Controller
o
o
o
o
Supports “Native Mode” Register and Interrupts
Independent timing of up to 4 drives
Ultra ATA/100/66/33, BMIDE and PIO modes
Tri-state modes to enable swap bay
Interrupt Controller
Page 37
PPC-5190 Flat Panel PC
o
o
o
o
o
Supports up to 8 PCI interrupt pins
Supports PCI 2.3 Message Signaled Interrupts
Two cascaded 82C59 with 15 interrupts
Integrated I/O APIC capability with 24 interrupts
Supports Front Side Bus interrupt delivery
High-Precision Event Timers
1.5 V operation with 3.3 V I/O
o
5V tolerant buffers on IDE, PCI, USB Overcurrent and Legacy signals
Integrated 1.5 V Voltage Regulator (INTVR) for the Suspend wells
Enhanced DMA Controller
o
o
o
o
Two cascaded 8237 DMA controllers
PCI DMA: Supports PC/PCI — Includes two PC/PCI REQ#/GNT# pairs
Supports LPC DMA
Supports DMA Collection Buffer to provide Type-F DMA performance for
all DMA channels
Real-Time Clock
o
o
o
256-byte battery-backed CMOS RAM
Integrated oscillator components
Lower Power DC/DC Converter implementation
2.4 Graphics Support
The Intel® Extreme Graphics 2 is integrated on the Intel® 852GME Northbridge chipset. The
Intel® Extreme Graphics 2 features are listed below.
Enhanced Rapid Pixel and Texel Rendering: Optimized visual quality and
performance from the addition of hardware to support of texel formatting,
bicubic filter, color blending accuracy, and video mixing render, resulting in
optimized visual quality and performance.
Zone Rendering 2 Technology: Enhances the performance of zone
rendering by using larger zones and new commands that improve graphics
pipeline efficiency.
Dynamic Video Memory Technology v2.0: Increases total system
performance by optimizing the efficiency of AGP dynamic video memory by
increasing its size of Video RAM allocation to 96 MB.
Page 38
PPC-5190 Flat Panel PC
Enhanced Intelligent Memory Management: Improves memory bandwidth
efficiency and platform performance by improving the memory management
arbitration between CPU, system memory and graphics memory.
Intel® Extreme Graphics 2 specifications are listed below:
Enhanced 2D:
o
o
o
o
o
o
o
o
o
o
256-bit internal path
8/16/32bpp
DirectDraw*, GDI, GDI+
Anti-aliased text support
Alpha blending
Alphas stretch blitter
Hardware alpha blended RGB cursor
Color space conversion
5x2 overlay support
Rotate, scale and translate operations
High-performance 3D:
o
o
o
o
o
o
o
o
o
o
256-bit internal path
32bpp/ 24ZorW/ 8 Stencil
DX7*/DX8*/OGL*1.1
DXTn texture compression
Up to 4 textures / pixel on a single pass
Cubic reflection map
Embossed/DOT3 bump mapping
Multi-texture
DOT3 bump-mapping
Point sprites
Video and Display:
o
o
o
o
o
DirectShow*/DirectVA*
Hardware motion compensation support for DVD playback
4x2 overlay filter
350 MHz DAC frequency
Maximum DVO pixel rate of up to 330MP/s
Page 39
PPC-5190 Flat Panel PC
o
Flat panel monitors and TV-out support via AGP Digital Display (ADD)
cards
o
350 MHz DAC for 1800x1440 @ 85Hz max CRT resolution or
[email protected] max FP resolution
o
o
o
o
Synchronous display for dual monitor capabilities
350MHz RAMDAC for up to QXGA analog monitor support
Dual DVO ports for up to QXGA digital display support
Multiple display types (LVDS, DVI, TV-out, CRT)
2.5 Peripheral Device Interfaces, Connectors, and Slots
The peripheral device connectors, interfaces and slots on the POS-8520 motherboard are
listed in the sections below.
2.5.1 OEM Options
Many of the peripheral device connectors listed below are not connected to any devices.
These connectors are reserved for OEM customizations. For a customized option, please
contact the vendor, reseller or IEI sales representative.
2.5.2 Internal Slots
The slots listed below can all be found on the POS-8520 motherboard.
2 x DDR DIMM sockets
1 x CFII slot
1 x PCI slot
2.5.3 Internal Peripheral Device Connectors
The peripheral device connectors listed below are located on the POS-8520 motherboard.
Pinouts for these connectors can be found in Appendix A.
1 x ATX 12V power connector
1 x ATX power connector
2 x Audio connectors
1 x DIO connector
Page 40
PPC-5190 Flat Panel PC
3 x Fan connectors
1 x FDD connector
2 x IDE device connectors
1 x IrDA connector
1 x Keyboard connector
1 x PS/2 mouse connector
1 x LCD backlight connector
1 x LVDS interface connector
1 x Multi panel connector
1 x Parallel port connector
1 x Reset connector
2 x Serial ATA connectors
6 x Serial port connectors
6 x USB connectors
1 x VGA connector
Page 41
PPC-5190 Flat Panel PC
2.5.4 External Peripheral Device Connectors
The peripheral device connectors listed below are located on the rear panel of the
POS-8520 motherboard. Pinouts for these connectors can be found in Appendix A.
3 x Audio jack connectors
1 x Keyboard connector
1 x Mouse connector
2 x RJ-45 Ethernet connectors
1 x Serial port connector (COM)
1 x VGA connector
2 x USB ports
Page 42
PPC-5190 Flat Panel PC
Chapter
3
3 Installation and
Configuration
Page 43
PPC-5190 Flat Panel PC
3.1 Installation Precautions
When installing the PPC-5190, please follow the precautions listed below:
Turn power off: When installing the PPC-5190 make sure the power is off.
Failing to turn off the power may cause severe injury to the body and/or
damage to the system.
Certified Engineers: Only certified engineers should install and modify
on-board functions.
Mounting: The PPC-5190 is a heavy device. When mounting the system onto
a rack, panel, wall or arm please make sure that at least two people are
assisting with the procedure.
Anti-static Discharge: If a user open the rear panel of the PPC-5190, to
configure the jumpers or plug in added peripheral devices, ground themselves
first and wear and anti-static wristband.
3.2 Preinstalled Components
The following components are all preinstalled.
Motherboard
19” TFT LCD
19” Touch screen (T-R model only)
Power switch
Power supply
Inverter board
PCI riser card
System cooling fans
Preinstalled OEM customizations may include the following.
CPU
HDD
FDD
CD drive
DIMM
Page 44
PPC-5190 Flat Panel PC
Removal and reinstallation of some of the components are described in Chapter 4.
3.3 Installation and Configuration Steps
The following installation steps must be followed.
Step 1: Unpack the PPC-5190.
Step 2: Set the jumper settings.
Step 3: Install HDD, FDD and CD drive.
Step 4: Mount the PPC-5190 flat panel PC.
Step 5: Connect peripheral devices to the bottom panel of the PPC-5190.
Step 6: Configure the system.Step 0:
3.4 Unpacking
To unpack the PPC-5190 flat panel PC, follow the steps below:
WARNING!
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the PPC-5190 flat panel PC has
been properly installed. The plastic cover ensures the screen is protected
during the installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors to cut the tape that seals the
top side of the external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors to cut the tape that seals the
top side of the internal (first) box.
Step 4: Lift the monitor out of the boxes.
Page 45
PPC-5190 Flat Panel PC
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Make sure all the components listed in the packing list are present.Step 0:
3.4.1 Packing List
The PPC-5190 flat panel PC is shipped with the following components:
1 x Carton
1 x Power cord
1 x Screw kit
1 x HDD IDE cable (44 pin + 2 x 40 pin)
1 x HDD IDE cable (44 pin + 40 pin)
1 x HDD SATA cable
1 x Driver CD (including user manual)
1 x CPU cooler
1 x CD-ROM installation kit
1 x FDD installation kit
1 x HDD bracket
1 x Jumper pack
1 x Wall-mounting kit
1 x Panel-mounting kit
1 x Touch screen driver CD (T-R model only)
1 x Touch pen (T-R model only)
3.5 Jumper Settings
NOTE:
These jumper settings and the jumper locations are described in detail in the
user manual that came with the POS-8520 motherboard. Please refer to the
manual for more detailed descriptions of the jumper settings.
Page 46
PPC-5190 Flat Panel PC
NOTE:
A jumper is a metal bridge that is used to close an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover)
that slides over the pins to connect them. To CLOSE/SHORT a jumper means
connecting the pins of the jumper with the plastic clip and to OPEN a jumper
means removing the plastic clip from a jumper.
The POS-8520 comes with fifteen jumpers (Table 3-1).
Jumper
Type
Label
Clear CMOS Setup
3-pin header
JP1
JP6
JP7
JP8
COM# RI and Voltage Selection
3-pin header
JP9
JP13
JP14
JP15
JP16
12-pin header
JP10
6-pin header
JP20
CompactFlash Card Setup
2-pin header
JP12
CPU Voltage Setting
10-pin header
S3
Keyboard/Mouse Power Source
3-pin header
JP18
LCD Voltage Select
6-pin header
JP2
COM2 RS-232/422/485 Setup
Table 3-1: Onboard Jumpers
Page 47
PPC-5190 Flat Panel PC
3.5.1 Remove the Back Cover
The back cover is secured to the chassis with fourteen retention screws, eleven on the
rear panel and two on the bottom panel (Figure 3-1). Remove the fourteen retention
screws and lift the cover off the PPC-5190.
Figure 3-1: Back Cover Retention Screws
Page 48
PPC-5190 Flat Panel PC
3.5.2 CF Card Setup (JP12)
The CF Card Setup jumper configures a CF card as either the slave or the master.
JP12
DESCRIPTION
Open
Slave (Default)
Close
Master
Table 3-2: CF Card Setup Jumper Settings
3.5.3 Clear CMOS Setup (JP1)
If the motherboard fails to boot due to improper BIOS settings, use this jumper to clear the
CMOS data and reset the system BIOS information. To do this, use the jumper cap to
close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
If the “CMOS Settings Wrong” message displays during the boot up process, try to correct
the fault by pressing the F1 to enter the CMOS Setup menu. Then do one of the following:
Enter the correct CMOS setting
Load Optimal Defaults
After one of the above has been done, save the changes and exit the CMOS Setup menu.
JP1
DESCRIPTION
1-2 closed
Normal (Default)
2-3 closed
Clear CMOS
Table 3-3: Clear CMOS Jumper Settings
Page 49
PPC-5190 Flat Panel PC
3.5.4 COM2 Port RS232/422/485 Selection (JP10, JP20)
The COM Port jumper configures the COM2 serial port.
JP10
JP20
DESCRIPTION
1-2,4-5,7-8,10-11 closed
1-3 closed
RS232 (default)
2-3,5-6,8-9,11-12 closed
3-5, 2-4 closed
RS422
2-3,5-6,8-9,11-12 closed
3-5, 4-6 closed
RS485
Table 3-4: COM2 Port Jumper Settings
3.5.5 COM port RI and Voltage Selection
Use JP7 and JP9 to set pin 9 of COM1 as signal RI or voltage source.
JP9
DESCRIPTION
2-3 closed
COM1 RI PIN Use RI
1-2 closed
COM1 RI PIN Use Voltage
Table 3-5: COM1 RI and Voltage Selection Jumper
JP7
DESCRIPTION
2-3 closed
COM1 RI PIN Use Voltage +12V
1-2 closed
COM1 RI PIN Use Voltage +5V
Table 3-6: COM1 RI Voltage Selection Jumper
NOTE:
The use of pin 2-3 or pin 1-2 of JP7 does not make any difference when pin 2-3
of JP9 is in use.
Use JP6 and JP8 to set pin 9 of COM2 as signal RI or voltage source.
Page 50
PPC-5190 Flat Panel PC
JP8
DESCRIPTION
2-3 closed
COM2 RI PIN Use RI
1-2 closed
COM2 RI PIN Use Voltage
Table 3-7: COM2 RI and Voltage Selection Jumper
JP6
DESCRIPTION
2-3 closed
COM2 RI PIN Use Voltage +12V
1-2 closed
COM2 RI PIN Use Voltage +5V
Table 3-8: COM2 RI Voltage Selection Jumper
Use JP13 and JP15 to set pin 9 of COM3 as signal RI or voltage source.
JP15
DESCRIPTION
2-3 closed
COM3 RI PIN Use RI
1-2 closed
COM3 RI PIN Use Voltage
Table 3-9: COM3 RI and Voltage Selection Jumper
JP13
DESCRIPTION
2-3 closed
COM3 RI PIN Use Voltage +12V
1-2 closed
COM3 RI PIN Use Voltage +5V
Table 3-10: COM3 RI Voltage Selection Jumper
Use JP14 and JP16 to set pin 9 of COM4 as signal RI or voltage source.
JP16
DESCRIPTION
2-3 closed
COM4 RI PIN Use RI
1-2 closed
COM4 RI PIN Use Voltage
Table 3-11: COM4 RI and Voltage Selection Jumper
Page 51
PPC-5190 Flat Panel PC
JP14
DESCRIPTION
2-3 closed
COM4 RI PIN Use Voltage +12V
1-2 closed
COM4 RI PIN Use Voltage +5V
Table 3-12: COM4 RI Voltage Selection Jumper
3.5.6 Keyboard and Mouse Power Source Setting (JP18)
JP18
DESCRIPTION
1-2 closed
VCC (default)
2-3 closed
5VSB
Table 3-13: Keyboard and Mouse Power Source Setting
3.5.7 LCD Voltage Setup (JP2)
WARNING:
Do not change this voltage. This voltage has been preset and is compatible
with the currently installed 17” TFT LCD screen. Change this jumper setting
may cause damage to the system.
The LCD Voltage Setup jumper sets the voltage for the LCD screen. This setting MUST
NOT be changed.
JP2
DESCRIPTION
1-2 closed
+3.3V (default)
3-4 closed
+5V
5-6 closed
+12V
Table 3-14: LCD Voltage Setup Jumper Settings
Page 52
PPC-5190 Flat Panel PC
3.6 HDD, FDD and CD Drive Installation
3.6.1 HDD Installation
To install a HDD, please follow the steps below:
Step 1: Remove the back cover (Section 3.5.1).
Step 2: The HDD bracket is attached to the elevated platform by four retention screws.
Remove the four retention screws from the elevated platform (Figure 3-2).
Figure 3-2: HDD Retention Screws
Step 3: Attach the HDD bracket to the HDD. To do this, align the four retention screw
holes in both side of HDD bracket with the retention screw holes on the side of
the HDD. Insert two retention screws into the bracket on both sides of the HDD.
Step 4: Install the HDD into the PPC-5190 by aligning the retention screw holes in the
base of the HDD bracket with the retention screw holes on the elevated platform.
Insert the four retention screws into the base of the HDD bracket.
Step 5: Connect the IDE/SATA cable from the IDE/SATA connector on the motherboard
to the rear of HDD.Step 0:
Page 53
PPC-5190 Flat Panel PC
3.6.2 FDD Installation
To install the FDD, please follow the steps below:
Step 1: Remove the back cover (Section 3.5.1).
Step 2: The FDD bracket is attached to the elevated platform by two retention screws
(Figure 3-3). Remove the two retention screws from the elevated platform.
Step 3: Remove the FDD bracket by sliding toward the HDD.
Figure 3-3: FDD Retention Screws
Step 4: Attach the FDD adapter to the FDD by aligning the two retention screw holes in
the FDD adapter with the retention screw holes on the rear side of the FDD
bracket. Insert two retention screws into the adapter (Figure 3-4). Connect the
FDD adapter and FDD with ribbon cable.
Page 54
PPC-5190 Flat Panel PC
Figure 3-4: FDD Adapter and FDD Bracket Installation
Step 5: Attach the FDD bracket to the FDD. To do this, align the four retention screw
holes in the FDD bracket with the retention screw holes on the sides of the FDD.
Insert four retention screws into the bracket of the FDD.
Step 6: Reinstall the FDD bracket onto the elevated platform with the previously
removed two retention screws.
Step 7: Connect the FDD ribbon cable and the power cable from the connectors on the
motherboard and the PSU to the rear of the FDD.Step 0:
3.6.3 CD Drive Installation
To install a CD drive, please follow the steps below.
Step 1: Attach a CD drive adapter to a CD drive by aligning the two retention screw
holes in the CD drive adapter with the retention screw holes on the rear side of
the CD drive.
Step 2: Place two spacers between the CD drive and CD drive adapter.
Step 3: Insert two retention screws and secure the adapter to the CD drive (Figure 3-5).
Page 55
PPC-5190 Flat Panel PC
Figure 3-5: CD Drive Adapter Installation
Step 4: Remove the back cover of the PPC-5190 (see Section 3.5.1).
Step 5: The CD drive blank plate assembly is attached to the rear panel by two retention
screws (Figure 3-6).
Figure 3-6: CD Drive Retention Screws
Remove the two retention screws from the bottom panel and slide the CD drive
blank plate assembly toward the PCI riser card until it can be lifted out of the
chassis (Figure 3-7).
Page 56
PPC-5190 Flat Panel PC
Figure 3-7: Remove CD Drive
Step 6: The CD drive blank plate assembly consists of a blank plate and two brackets
that attach the assembly to the chassis. The two brackets each have two screws
that attach them to the blank plate. Remove the four screws that attach the
brackets to the blank plate. Figure 3-8 shows the underside of the CD drive
blank plate assembly with the four screws to be removed.
Figure 3-8: CD Drive Blank Plate Assembly
Step 7: Attach the two brackets to a CD drive with the four previously removed screws.
Be sure to orient the brackets properly before attaching them to the CD drive.
Figure 3-9 shows two views of a CD drive with the brackets attached and the
proper retention screws to use.
Page 57
PPC-5190 Flat Panel PC
Figure 3-9: CD Drive Blank Plate Assembly
WARNING!
The two screws (black M2*3) shown in the left image of Figure 3-9 are
different from the two screws (silver M2*2) shown in the right. Please
secure the correct screws into the CD drive according to the images shown
in the Figure 3-9.
Step 8: Slide the CD drive into the PPC-5190 and align the two retention screw holes in
the side of the CD drive bracket with the retention screw holes on the bottom
panel.
Step 9: Reinsert the two previously removed retention screws.
Step 10: Connect the CD ribbon cable and the power cable from the connectors on the
motherboard and the PSU to the rear of the CD drive. Figure 3-10 shows a
properly installed CD drive.Step 0:
Page 58
PPC-5190 Flat Panel PC
Figure 3-10: CD Drive Installed
3.7 Mounting the System
WARNING!
When mounting the PPC-5190 flat panel PC onto an arm, wall or into a
panel, it is advisable to have more than one person help with the
installation to prevent accidental damage to the panel and avoid personal
injury.
The methods of mounting the PPC-5190 are:
Wall mounting
Panel mounting
Arm mounting
Rack mounting
The mounting methods are fully described below.
3.7.1 Wall Mounting
To mount the PPC-5190G flat panel PC onto a wall, please follow the steps below.
Page 59
PPC-5190 Flat Panel PC
Step 1: Select the location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four bracket screw holes on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into
the four pilot holes and tightening them (see Figure 3-11).
Figure 3-11: Wall-mounting Bracket
Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the
four screw holes on the real panel of the monitor and tighten until the screw
shank is secured against the rear panel (see Figure 3-12).
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes (see Figure
Page 60
PPC-5190 Flat Panel PC
3-12). Ensure that all four of the mounting screws fit snuggly into their respective
slotted holes.
NOTE:
In the diagram below the bracket is already installed on the wall.
Figure 3-12: Mount the Chassis
Step 9: Secure the panel PC with the wall-mounting kit. To do this, stick the protective
cushion to the wall-mounting kit first. Then, put the wall-mounting kit on the top
panel of the panel PC. Carefully mark the location of the wall-mounting kit screw
holes on the wall. Drill a pilot hole at the marked location on the wall. Secure the
wall-mounting kit to the wall by inserting a retention screw into the pilot hole on
the wall (Figure 3-13). This step is to avoid the panel PC being pushed apart
from the wall-mounting bracket accidentally. Step 0:
Page 61
PPC-5190 Flat Panel PC
Figure 3-13: Secure the Chassis
3.7.2 Panel/ Mounting
To mount the PPC-5190 flat panel PC into a panel, please follow the steps below.
NOTE:
The maximum panel thickness should be no more than 6mm.
Step 1: Select the position on the panel to mount the PPC-5190.
Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of
the PPC-5190. Take care that the panel section that is cut out is smaller than the
overall size of the metal frame that surrounds the PPC-5190 but just large
enough for the rear panel of the PPC-5190 to fit through (Figure 3-14).
Page 62
PPC-5190 Flat Panel PC
Figure 3-14: Cut the Panel
Step 3: Slide the PPC-5190 through the hole until the metal frame is flush against the
panel.
Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of
the PPC-5190, behind the metal frame (Figure 3-15). Refer to the mounting kit
packing list for the required number of mounting clamps.
Figure 3-15: Panel Mounting Clamp Positions
Page 63
PPC-5190 Flat Panel PC
Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic
caps at the front of all the screws are firmly secured to the panel (Figure 3-16).
Step 0:
Figure 3-16: Tighten the Panel Mounting Clamp Screws
3.7.3 Rack and Cabinet Installation
To mount the PPC-5190 monitor into a rack/cabinet, please follow the steps below.
Step 1: Secure the rack mounting bracket to two sides of the monitor using the supplied
retention screws (Figure 3-17). Each bracket requires four screws.
Step 2: Secure the rack mounting bracket to the rack by inserting and tightening the
supplied mounting nuts and bolts (Figure 3-17). Each bracket requires three
nuts and bolts for installation.Step 0:
Page 64
PPC-5190 Flat Panel PC
Figure 3-17: Rack Mounting
3.7.4 Arm Mounting
The PPC-5190 is VESA (Video Electronics Standards Association) compliant and can be
mounted on an arm with a 100mm interface pad. To mount the PPC-5190 on an arm,
please follow the steps below.
Step 1: The arm is a separately purchased item. Please correctly mount the arm onto
the surface it uses as a base. To do this, refer to the installation documentation
that came with the mounting arm.
NOTE:
When purchasing the arm please ensure that it is VESA compliant and that
the arm has a 100mm interface pad. If the mounting arm is not VESA
compliant, it cannot be used to support the PPC-5190 flat panel PC.
Step 2: Once the mounting arm has been firmly attached to its surface, lift the PPC-5190
flat panel PC onto the interface pad of the mounting arm.
Step 3: Align the retention screw holes on the mounting arm interface with those in the
PPC-5190 flat panel PC. The PPC-5190 flat panel PC arm mount retention
Page 65
PPC-5190 Flat Panel PC
screw holes are shown in Figure 3-18.
Figure 3-18: Arm Mount Retention Screw Holes
Step 4: Secure the PPC-5190 to the interface pad by inserting four retention screws
through the mounting arm interface pad and into the PPC-5190 flat panel PC.
Step 0:
3.8 External Peripheral Interface Connectors
3.8.1 LCD Panel Connection
A conventional CRT VGA 15-pin female D-SUB connector is located on the bottom panel
to connect the PPC-5190 flat panel PC to a second monitor.
NOTE:
To use the dual screen option, please configure this option in the Intel® Extreme
Graphics configuration settings. To do this, open the Control Panel, locate the
Intel® Extreme Graphics icon and click on it. Once opened, an option for Multiple
Display is available. Select this option and select notebook as the primary device.
3.8.2 Ethernet Connection
The two external peripheral interface RJ-45 connectors can be connected to an external
LAN to provide Internet connectivity to the flat panel PC.
Page 66
PPC-5190 Flat Panel PC
3.8.3 USB Connection
The external peripheral interface USB connectors provide easy and quick access to
external USB devices. The external peripheral interface USB connectors are a standard
connector and can easily be connected to other USB devices.
3.8.4 Keyboard and Mouse Connection
Two PS/2 connectors on the external peripheral interface panel facilitate the connection of
a mouse and a keyboard. To connect either device, plug the PS/2 connector at the end of
the keyboard or mouse cable into the corresponding PS/2 connector on the external
peripheral interface panel.
3.8.5 Parallel Port Connection
The parallel port is typically connected to a printer, but can also be connected to other
parallel devices.
3.8.6 Serial Port Connection
The external peripheral interface panel serial connectors provide easy and quick access to
external serial devices.
3.8.7 Audio Port Connection
The external peripheral interface panel audio ports provide line in, line out and speaker
connectivity.
Page 67
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 68
PPC-5190 Flat Panel PC
Chapter
4
4 System Maintenance
Page 69
PPC-5190 Flat Panel PC
4.1 System Maintenance Introduction
The following system components may require maintenance.
Motherboard
DIMM module
PSU module
Cooling fans
If these components fail, they must be replaced. Please contact the system reseller or
vendor to purchase replacement parts. Replacement instructions for the above listed
components are described below.
4.2 Motherboard Replacement
A user cannot replace a motherboard. If the motherboard fails it must be shipped back to
IEI to be replaced. If the system motherboard has failed, please contact the system vendor,
reseller or an IEI sales person directly.
4.3 Back Cover Removal and Elevated Platform Detachment
WARNING!
BEFORE REMOVING THE BACK COVER, MAKE SURE ALL POWER
TO THE SYSTEM HAS BEEN DISCONNECTED. Failing to do so may
cause severe damage to the PPC-5190 and injury to the user.
Page 70
PPC-5190 Flat Panel PC
WARNING!
PLEASE TAKE ANTISTATIC PRECAUTIONS WHEN WORKING WITH
THE INTERNAL COMPONENTS. The interior of the PPC-5190 contains
very sensitive electronic components. These components are easily
damaged by electrostatic discharge (ESD). Before working with the internal
components, make sure all anti-static precautions described earlier have
been observed.
4.3.1 Back Cover Removal
Please read the warnings at the beginning of Section 4.3 before attempting to remove the
PPC-5190 back cover.
To access the panel PC internal components, the back cover must be removed. To
remove the back cover, please follow the steps below.
Step 1: Remove the PPC-5190 from its mount (panel, wall, rack, arm, etc.).
Step 2: The back cover is secured to the chassis with fourteen retention screws, eleven
on the back cover and two on the bottom panel (Figure 4-1). Remove the
retention screws and lift the cover off the PPC-5190. Step 0:
Page 71
PPC-5190 Flat Panel PC
Figure 4-1: Rear Cover Retention Screws (Real Panel)
4.3.2 Detaching the Elevated Platform
Please read the warnings at the beginning of Section 4.3 before attempting to access any
PPC-5190 internal components.
The elevated platform supports the FDD, CD drive and HDD. Back cover removal is
discussed in Section 4.3.1. To detach the elevated platform, please follow the steps
below.
Step 1: Disconnect all FDD, CD drive and HDD cabling.
Page 72
PPC-5190 Flat Panel PC
Step 2: Remove the CD drive retention screws from the bottom panel (Figure 4-2).
Figure 4-2: CD Drive Retention Screws
Step 3: The elevated platform is secured to the chassis with twelve retention screws,
two on the internal platform (Figure 4-3), three on the top panel (Figure 4-4),
three on the right panel (Figure 4-5), two on the bottom panel (Figure 4-6) and
two on the PCI riser card (Figure 4-7). Remove the retention screws and lift the
elevated platform out of the chassis. Step 0:
Figure 4-3: Internal Elevated Platform Retention Screws
Figure 4-4: Elevated Platform Retention Screws (Top Panel)
Page 73
PPC-5190 Flat Panel PC
Figure 4-5: Elevated Platform Retention Screws (Right Panel)
Figure 4-6: Elevated Platform Retention Screws (Bottom Panel)
Figure 4-7: Elevated Platform Retention Screws (PCI Riser Card)
4.4 DIMM Replacement
Please read the warnings at the beginning of Section 4.3 before attempting to access any
PPC-5190 internal components.
Page 74
PPC-5190 Flat Panel PC
To install/replace the DIMM modules please follow the steps below.
Step 1: Remove the back cover (Section 4.3.1).
Step 2: Locate the DIMM socket on the motherboard near the right of the chassis. Push
down on the white levers of the socket until the DIMM module is dislodged from
the socket (Figure 4-8).
Figure 4-8: DIMM Socket Clip Locations
Step 3: Slowly slide the new DIMM module along the plastic guides at both ends of the
socket. Press the DIMM module down into the socket until it clicks into position
and the two handles have automatically locked the memory module into place.
Step 0:
4.5 PSU Module Replacement
Please read the warnings at the beginning of Section 4.3 before attempting to access any
PPC-5190 internal components.
If the PSU module has been damaged it must be replaced. To replace the PSU module,
please follow the steps below.
4.5.1 Remove the Old PSU
Step 1: Remove the back cover (Section 4.3.1).
Page 75
PPC-5190 Flat Panel PC
Step 2: Detach and remove the elevated platform (see Section 4.3.2).
Step 3: Disconnect all PSU connections including those to the motherboard (Figure 4-9)
and any disk drives.
Figure 4-9: PSU Motherboard Connectors
The PSU module is secured to the PPC-5190 flat panel PC with six retention screws, two
connect to the bottom panel (Figure 4-10), two connect to the internal PSU bracket
(Figure 4-12) which is connected to the chassis by two screws (Figure 4-11).
Step 4: Remove the PSU retention screws from the bottom panel (Figure 4-10).
Figure 4-10: PSU Bottom Panel Retention Screws
Step 5: Remove the retention screws that connect the PSU bracket to the chassis
(Figure 4-11).
Page 76
PPC-5190 Flat Panel PC
Figure 4-11: PSU Bracket to Chassis Retention Screws
Step 6: Remove the retention screws that connect the PSU to the PSU bracket
(Figure 4-12).Step 0:
Figure 4-12: PSU Bracket Retention Screws
4.5.2 Install the New PSU
To install a new PSU module, please follow the steps below.
Step 1: Attach the PSU bracket to the PSU module with the previously removed
retention screws.
Step 2: Insert the PSU module and bracket assembly into the chassis and attach the
PSU bracket to the chassis with the previously removed retention screws.
Step 3: Secure the PSU module to the chassis by reinserting the previously removed
retention screws through the bottom panel.
Page 77
PPC-5190 Flat Panel PC
Step 4: Bundle the cables of the new PSU module and secure them with a plastic tie
similar to the old PSU module.
Step 5: Reconnect all previously disconnected power connectors to the motherboard
and disk drives.
Step 6: Reattach the elevated platform.
Step 7: Replace the back cover.Step 0:
4.6 System Cooling Fan Replacement
Please read the warnings at the beginning of Section 4.3 before attempting to access any
PPC-5190 internal components.
If the system cooling fans have been damaged, they must be replaced. To replace the
system cooling fans, please follow the steps below.
4.6.1 Remove the Old System Cooling Fans
Step 1: Remove the back cover (Section 4.3.1).
Step 2: Detach and remove the elevated platform (see Section 4.3.2).
Step 3: Disconnect the system cooling fans from the motherboard (Figure 4-13).
Figure 4-13: System Cooling Fans Motherboard Connector
Page 78
PPC-5190 Flat Panel PC
Step 4: Remove the system cooling fans retention screws from the left panel
(Figure 4-14).
Figure 4-14: System Cooling Fans Left Panel Retention Screws
Step 5: Remove the system cooling fans from the chassis. Step 0:
4.6.2 Install the New System Cooling Fans
To install the new system cooling fans, please follow the steps below.
Step 1: Insert the system cooling fans into the chassis and attach to the left panel with
the previously removed retention screws.
Step 2: Rebundle the new fan wires and tie them to the chassis like the old fan wires.
Step 3: Reconnect the new fan connector to the motherboard.
Step 4: Reattach the elevated platform.
Step 5: Replace the back cover.Step 0:
Page 79
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 80
PPC-5190 Flat Panel PC
Chapter
5
5 AMI BIOS
Page 81
PPC-5190 Flat Panel PC
5.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
5.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP”
message appears on the screen. 0.
If the message disappears before the DELETE key is pressed, restart the computer and try
again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the “+” and “-“ keys to
change entries, press F1 for help and press ESC to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
“+” key
Increase the numeric value or make changes
“-“ key
Decrease the numeric value or make changes
Page 82
PPC-5190 Flat Panel PC
Key
Function
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
5.1.4 Unable to Reboot After Configuration Changes
If the computer cannot boot after changes are made to the system configuration, use the
jumper described in Section 3.5.3 to reset the CMOS defaults.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Power Changes power management settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 83
PPC-5190 Flat Panel PC
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version: Current BIOS version
Build Date: Date the current BIOS version was made
ID: Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
Page 84
Type: Names the currently installed processor
Speed: Lists the processor speed
PPC-5190 Flat Panel PC
o
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size: Lists memory size
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system to
malfunction. Make sure that the settings made are compatible with the
hardware.
Page 85
PPC-5190 Flat Panel PC
CPU Configuration (Section 5.3.1)
IDE Configuration (Section 5.3.2)
Floppy Configuration (Section 5.3.3)
SuperIO Configuration (Section 5.3.4)
Hardware Health Configuration (Section 5.3.5)
ACPI Configuration (Section 5.3.6)
MPS Configuration (Section 5.3.7)
Remote Access Configuration (Section 5.3.8)
USB Configuration (Section 5.3.9)
BIOS Menu 2: Advanced
Page 86
PPC-5190 Flat Panel PC
5.3.1 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and
configure the CPU.
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
Page 87
PPC-5190 Flat Panel PC
The following CPU Configuration menu items can be configured.
Max CPUID Value Limit
Hyper Threading Technology
Max CUPID Value Limit [Disabled]
NOTE:
If the OS is NT, this value must be set to enabled.
Disabled
DEFAULT
Disables legacy OSes that cannot support CPUs with
extended CUPID functions from booting up
Enables legacy OSes that cannot support CPUs with
Enabled
extended CUPID functions to boot up
Hyper Threading Technology [Disabled]
Disabled
Enabled
Page 88
DEFAULT
Disables the use of hyper threading technology
Enables the use of hyper threading technology
PPC-5190 Flat Panel PC
5.3.2 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of
the IDE devices installed in the system.
BIOS Menu 4: IDE Configuration
IDE Configuration [P-ATA Only]
Use IDE Configuration option to setup the configuration of the hard drive interfaces.
The hard drive interfaces are disabled.
Disabled
P-ATA Only
DEFAULT
The hard drive interfaces are configured as P-ATA
only.
S-ATA Only
The hard drive interfaces are configured as S-ATA
only.
Page 89
PPC-5190 Flat Panel PC
The hard drive interfaces are configured as P-ATA and
P-ATA&S-ATA
S-ATA.
S-ATA Running Enhanced Mode [Yes]
Use S-ATA Running Enhanced Mode option to select whether the S-ATA interface is
running in enhanced mode or legacy mode.
Yes
The S-ATA interface is running in enhanced mode.
DEFAULT
The S-ATA interface is running in legacy mode.
No
P-ATA Channel Selection [Both]
Use P-ATA Channel Selection option to select the active IDE channels.
The primary P-ATA channel is set to be the active IDE
Primary
channel.
The secondary P-ATA channel is set to be the active
Secondary
IDE channel.
Both
DEFAULT
The primary and secondary P-ATA channel are both
set to be the active IDE channels.
S-ATA Ports Definition [PO-3rd./P1-4th.]
Use S-ATA Ports Definition option to select the physical ports for S-ATA.
PO-3rd./P1-4th.
PO-4th. /P1-3rd.
Page 90
DEFAULT
Set the physical ports (PO/PI) to be 3rd./4th.
Set the physical ports (PO/PI) to be 4th./3rd.
PPC-5190 Flat Panel PC
Configure S-ATA as RAID [No]
The Configure S-ATA as RAID option can only be selected if the IDE Configuration option
is set to “P-ATA Only”. Use Configure S-ATA as RAID option to configure the S-ATA
interface as RAID.
No
DEFAULT
The S-ATA interface cannot be configured as RAID drive.
The S-ATA interface can be configured as RAID drive.
Yes
Hard Disk Write Protect [Disabled]
The Hard Disk Write Protect BIOS option protects the hard disks from being overwritten.
This menu item is only effective if the device is accessed through the BIOS.
Disabled
DEFAULT
Enabled
Allows hard disks to be overwritten
Prevents hard disks from being overwritten
IDE Detect Time Out (Sec) [35]
The IDE Detect Time Out (Sec) BIOS option specifies the maximum time (in seconds) the
AMI BIOS will search for IDE devices. This allows fine-tunes the settings to allow for faster
boot times. The following configuration options are available.
0 seconds
5 seconds
10 seconds
15 seconds
20 seconds
25 seconds
30 seconds
35 seconds
DEFAULT
The best setting to use if the onboard IDE controllers are set to a specific IDE disk drive in
the AMIBIOS is “0 seconds” and a large majority of ultra ATA hard disk drives can be
detected well within “5 seconds” (the default setting).
Page 91
PPC-5190 Flat Panel PC
ATA (PI) 80Pin Cable Detection [Host & Device]
When an Ultra ATA/66, an Ultra ATA/100 or an Ultra ATA/133 IDE hard disk drive is used,
an 80-conductor ATA cable must be used. The 80-conductor ATA cable is plug compatible
with the standard 40-conductor ATA cable. The system must detect the presence of
correct cable so that the AMIBIOS can instruct the drive to run at the correct speed for the
cable type detected.
The ATA (PI) 80Pin Cable Detection BIOS option determines how the IDE cable will be
detected.
Host & Device
DEFAULT
Both the motherboard onboard IDE controller and
IDE disk drive are used to detect the type of IDE
cable used.
Host
The motherboard onboard IDE controller detects
the type of IDE cable used.
Device
The IDE disk drive to detects the type of IDE cable
used.
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
Fourth IDE Master
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
Page 92
PPC-5190 Flat Panel PC
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 5.3.2.1 appear.
5.3.2.1 IDE Master, IDE Slave
Use the IDE Master and IDE Slave configuration menu to view both primary and
secondary IDE device details and configure the IDE devices connected to the system.
BIOS Menu 5: IDE Master and IDE Slave Configuration
Auto-Detected Drive Parameters
The “grayed-out” items in the left frame are IDE disk drive parameters automatically
detected from the firmware of the selected IDE disk drive. The drive parameters are listed
as follows:
Device: Lists the device type (e.g. hard disk, CD-ROM etc.)
Type: Indicates the type of devices a user can manually select
LBA/Large Mode: Indicates whether the LBA (Logical Block Addressing) is a
Page 93
PPC-5190 Flat Panel PC
method of addressing data on a disk drive is supported or not.
Block (Multi-Sector Transfer): Block mode boosts IDE drive performance by
increasing the amount of data transferred. Only 512 bytes of data can be
transferred per interrupt if block mode is not used. Block mode allows
transfers of up to 64 KB per interrupt.
PIO Mode: Indicates the PIO mode of the installed device.
S.M.A.R.T.: Indicates whether or not the Self-Monitoring Analysis and
Reporting Technology protocol is supported.
32Bit Data Transfer: Enables 32-bit data transfer.
Type [Auto]
Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from
after the Power-On Self-Test (POST) is complete.
BIOS is prevented from searching for an IDE disk
Not Installed
drive on the specified channel.
Auto
DEFAULT
The BIOS auto detects the IDE disk drive type
attached to the specified channel. This setting should
be used if an IDE hard disk drive is attached to the
specified channel.
CD/DVD
The CD/DVD option specifies that an IDE CD-ROM
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
IDE disk drives on the specified channel.
ARMD
This option specifies an ATAPI Removable Media
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
Page 94
PPC-5190 Flat Panel PC
Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical
Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
BIOS is prevented from using the LBA mode control on
Disabled
the specified channel.
Auto
DEFAULT
BIOS auto detects the LBA mode control on the specified
channel.
Block (Multi Sector Transfer) [Auto]
Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device
supports multi-sector transfers.
BIOS is prevented from using Multi-Sector Transfer on the
Disabled
specified channel. The data to and from the device occurs
one sector at a time.
Auto
DEFAULT
BIOS auto detects Multi-Sector Transfer support on the
drive on the specified channel. If supported the data
transfer to and from the device occurs multiple sectors at
a time.
PIO Mode [Auto]
Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
BIOS auto detects the PIO mode. Use this value if the IDE disk
drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
Page 95
PPC-5190 Flat Panel PC
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
S.M.A.R.T [Auto]
Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and
Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
DEFAULT
BIOS auto detects HDD SMART support.
Disabled
Prevents BIOS from using the HDD SMART feature.
Enabled
Allows BIOS to use the HDD SMART feature
32Bit Data Transfer [Disabled]
Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers.
Disabled
Enabled
DEFAULT
Prevents the BIOS from using 32-bit data transfers.
Allows BIOS to use 32-bit data transfers on supported
hard disk drives.
Page 96
PPC-5190 Flat Panel PC
5.3.3 Floppy Configuration
Use the Floppy Configuration menu (BIOS Menu 6) to set or change the configurations for
floppy disk drives.
BIOS Menu 6: Floppy Configuration
Floppy A [1.44 MB 3½”]
The Floppy A configuration option determines the types of the floppy drive installed in the
system. The following configuration options are available.
Disabled (default)
360 KB 5¼”
1.2 MB 5¼”
720 KB 3 ½”
1.44 MB 3½”
2.88 MB 3½”
Page 97
PPC-5190 Flat Panel PC
5.3.4 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations
for the FDD controllers, parallel ports and serial ports.
BIOS Menu 7: Super IO Configuration
On Board Floppy Controller [Enabled]
Allows BIOS to disable the floppy controller
Disabled
Enabled
DEFAULT
Allows BIOS to enable the floppy controller
Serial Port1 Address [3F8/IRQ4]
Use the Serial Port1 Address option to select the Serial Port 1 base address.
Disabled
Page 98
No base address is assigned to Serial Port 1
PPC-5190 Flat Panel PC
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 1 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Address [2F8/IRQ3]
Use the Serial Port2 Address option to select the Serial Port 2 base address.
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
DEFAULT
Serial Port 2 I/O port address is 3F8 and the interrupt
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Mode [Normal]
Use the Serial Port2 Mode option to select the Serial Port2 operational mode.
Normal
DEFAULT
Serial Port 2 mode is normal
IrDA
Serial Port 2 mode is IrDA
ASK IR
Serial Port 2 mode is ASK IR
Parallel Port Address [378]
Use the Parallel Port Address option to select the parallel port base address.
Page 99
PPC-5190 Flat Panel PC
No base address is assigned to the Parallel Port
Disabled
378
DEFAULT
Parallel Port I/O port address is 378
278
Parallel Port I/O port address is 278
3BC
Parallel Port I/O port address is 3BC
Parallel Port Mode [Normal]
Use the Parallel Port Mode option to select the mode the parallel port operates in.
Normal
DEFAULT
The normal parallel port mode is the standard mode
for parallel port operation.
EPP
The parallel port operates in the enhanced parallel
port mode (EPP). The EPP mode supports
bi-directional communication between the system
and the parallel port device and the transmission
rates between the two are much faster than the
Normal mode.
ECP
The
parallel
port
operates
in
the
extended
capabilities port (ECP) mode. The ECP mode
supports bi-directional communication between the
system and the parallel port device and the
transmission rates between the two are much faster
than the Normal mode
EPP+ECP
The parallel port is also be compatible with EPP and
ECP devices
Page 100
PPC-5190 Flat Panel PC
Parallel Port IRQ [IRQ7]
Use the Parallel Port IRQ selection to set the parallel port interrupt address.
IRQ5 is assigned as the parallel port interrupt address
IRQ5
IRQ7
DEFAULT
IRQ7 is assigned as the parallel port interrupt address
Digital I/O Address [280h]
Use the Digital I/O Address option to select the interrupt address for digital I/O.
200h
Digital I/O address is 200h
220h
Digital I/O address is 220h
240h
Digital I/O address is 240h
260h
Digital I/O address is 260h
280h
DEFAULT
Digital I/O address is 280h
Serial Port3 Address [3E8]
Use the Serial Port3 Address option to select the base addresses for serial port 3
No base address is assigned to serial port 3
Disabled
3E8
DEFAULT
Serial port 3 I/O port address is 3E8
2E8
Serial port 3 I/O port address is 2E8
2F0
Serial port 3 I/O port address is 2F0
2E0
Serial port 3 I/O port address is 2E0
Page 101
PPC-5190 Flat Panel PC
Serial Port3 IRQ [11]
Use the Serial Port3 IRQ option to select the interrupt address for serial port 3.
4
Serial port 3 IRQ address is 4
9
Serial port 3 IRQ address is 9
10
Serial port 3 IRQ address is 10
11
DEFAULT
Serial port 3 IRQ address is 11
Serial Port4 Address [2E8]
Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
Disabled
No base address is assigned to serial port 4
3E8
Serial port 4 I/O port address is 3E8
2E8
DEFAULT
Serial port 4 I/O port address is 2E8
2F0
Serial port 4 I/O port address is 2F0
2E0
Serial port 4 I/O port address is 2E0
Serial Port4 IRQ [10]
Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
3
Serial port 4 IRQ address is 3
9
Serial port 4 IRQ address is 9
10
11
Page 102
DEFAULT
Serial port 4 IRQ address is 10
Serial port 4 IRQ address is 11
PPC-5190 Flat Panel PC
Serial Port5 Address [2F0]
Use the Serial Port5 IRQ option to select the interrupt address for serial port 5.
Disabled
No base address is assigned to serial port 5
3E8
Serial port 5 I/O port address is 3E8
2E8
Serial port 5 I/O port address is 2E8
2F0
DEFAULT
Serial port 5 I/O port address is 2F0
Serial port 5 I/O port address is 2E0
2E0
Serial Port5 IRQ [11]
Use the Serial Port5 IRQ option to select the interrupt address for serial port 5.
4
Serial port 5 IRQ address is 4
9
Serial port 5 IRQ address is 9
10
Serial port 5 IRQ address is 10
11
DEFAULT
Serial port 5 IRQ address is 11
Serial Port6 Address [2E0]
Use the Serial Port6 IRQ option to select the interrupt address for serial port 6.
Disabled
No base address is assigned to serial port 6
3E8
Serial port 6 I/O port address is 3E8
2E8
Serial port 6 I/O port address is 2E8
2F0
Serial port 6 I/O port address is 2F0
2E0
DEFAULT
Serial port 6I/O port address is 2E0
Page 103
PPC-5190 Flat Panel PC
Serial Port6 IRQ [10]
Use the Serial Port6 IRQ option to select the interrupt address for serial port 6.
3
Serial port 6 IRQ address is 3
9
Serial port 6 IRQ address is 9
10
11
DEFAULT
Serial port 6 IRQ address is 10
Serial port 6 IRQ address is 11
5.3.5 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 8) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 8: Hardware Health Configuration
Page 104
PPC-5190 Flat Panel PC
H/W Health Function [Enabled]
Disables the health monitoring function
Disabled
Enabled
DEFAULT
Enables the health monitoring function
If the H/W Health Function is enabled different system parameters and values are shown.
The system parameters that are monitored are:
System Temperatures: The following system temperatures are monitored
o
o
CPU Temperature
System Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
o
o
Fan1 Speed
Fan2 Speed
Fan3 Speed
Voltages: The following system voltages are monitored
o
o
o
o
o
o
Vcore
+1.50V
+3.30V
+5.00V
+12.0V
5VSB
Page 105
PPC-5190 Flat Panel PC
5.3.6 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 9) configures the Advanced Configuration and
Power Interface (ACPI) and Power Management (APM) options.
BIOS Menu 9: ACPI Configuration
Page 106
PPC-5190 Flat Panel PC
5.3.6.1 General ACPI Configuration
Use the General ACPI Configuration menu (BIOS Menu 10) to select the ACPI state when
the system is suspended.
BIOS Menu 10: General ACPI Configuration
Suspend Mode [S1 (POS)]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
S1 (POS)
The system enters S1(POS) sleep state. The system
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
Page 107
PPC-5190 Flat Panel PC
5.3.6.2 Advanced ACPI Configuration
Use the Advanced ACPI Configuration menu (BIOS Menu 11) to select the ACPI state
when the system is suspended.
BIOS Menu 11: Advanced ACPI Configuration
Page 108
PPC-5190 Flat Panel PC
ACPI 2.0 Features [No]
Use the ACPI 2.0 Features option to enable the ACPI (Advanced Configuration and Power
Interface) features. By enabling this feature the system RSDP (Root System Description
Pointer) is able to obtain physical addresses for other 64-bit fixed system description
tables.
No
DEFAULT
RSDP pointers to 64-bit fixed systems are not provided to the
system
Yes
RSDP pointers to 64-bit fixed systems are provided to the
system
ACPI APIC Support [Enabled]
Use the ACPI APIC Support option to add a pointer to an ACPI APIC table in the RSDT
(Root System Description Table). The RSDT is an array of pointers that direct the system
to the physical addresses of other description tables. The RSDT is the main ACPI table.
The RSDP is located in low memory space of the system and provides the physical
address of the RSDT. The RSDT itself is identified in memory because it starts with the
signature "RSDT."
Pointers to the APIC APIC table are not be provided in the
Disabled
RSDT
Enabled
DEFAULT
Pointers to the APIC APIC table are provided in the RSDT
Page 109
PPC-5190 Flat Panel PC
APIC ACPI SCI IRQ [Disabled]
Use APIC ACPI SCI IRQ option to enable the system to send a flag report to the ACPI OS
if a SCI IRQ interrupt event is made via the APIC.
Disabled
DEFAULT
No flag report is sent to the ACPI OS when there is a
"SCI IRQ" interrupt event.
Flag report is sent to the ACPI OS when there is a "SCI
Enabled
IRQ" interrupt event is made via the APIC.
AMI OEMB table [Enabled]
Use the AMI OEMB table option to add a pointer to an OEMB table in the RSDT table and
the Extended System Description Table (XSDT), which accommodates physical
addresses of description headers that are larger than 32-bits. Notice that both the XSDT
and the RSDT can be pointed to by the RSDP structure.
Pointers to the AMI OEMB table are not provided in the
Disabled
RSDT and the XSDT
Enabled
DEFAULT
Pointers to the AMI OEMB table are provided in the
RSDT and the XSDT
Headless Mode [Disabled]
Use the Headless Mode option to update the ACPI FACP (Fixed ACPI Description Table)
to indicate headless operations, i.e. a computer without a monitor, keyboard and mouse.
Disabled
Enabled
Page 110
DEFAULT
The FACP is not updated to indicate headless mode
The FACP is updated to indicate headless mode
PPC-5190 Flat Panel PC
5.3.7 MPS Configuration
Use the MPS Configuration menu (BIOS Menu 12) to select `he multi-processor table.
BIOS Menu 12: MPS Configuration
MPS Revision [1.4]
Use the Multiprocessor Specification (MPS) for OS option to specify the MPS version to
be used.
MPS version 1.1 is used
1.1
1.4
DEFAULT
MPS version 1.4 is used
Page 111
PPC-5190 Flat Panel PC
5.3.8 Remote Access Configuration
Use the Remote Access Configuration menu to configure remote access parameters. The
Remote Access Configuration is an AMIBIOS feature and allows a remote host running a
terminal program to display and configure the BIOS settings.
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities of
the system.
Disabled
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Flow Control
Redirection after BIOS POST
Terminal Type
VT-UTF8 Combo Key Support
These configuration options are discussed below.
Page 112
PPC-5190 Flat Panel PC
5.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information
and configure the USB settings.
BIOS Menu 13: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
Page 113
PPC-5190 Flat Panel PC
USB Function [8 USB Ports]
Use the USB Function BIOS option to select USB function support.
Disabled
USB function support disabled
2 USB Ports
USB function support two USB ports
4 USB Ports
USB function support four USB ports
6 USB Ports
USB function support six USB ports
8 USB Ports
DEFAULT
USB function support eight USB ports
Legacy USB Support [Disabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Disabled
DEFAULT
Legacy USB support disabled
Enabled
Legacy USB support enabled
Auto
Legacy USB support disabled if no USB devices are
connected
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Enabled
Disabled
Page 114
DEFAULT
USB 2.0 controller enabled
USB 2.0 controller disabled
PPC-5190 Flat Panel PC
5.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings.
WARNING!
Setting wrong values for the BIOS selections in the PCIPnP BIOS menu
may cause the system to malfunction.
BIOS Menu 14: PCI/PnP Configuration
Plug & Play O/S [No]
Use the Plug & Play O/S BIOS option to specify whether system plug and play devices are
configured by the operating system or the BIOS.
Page 115
PPC-5190 Flat Panel PC
No
DEFAULT
If the operating system does not meet the Plug and Play
specifications, this option allows the BIOS to configure all the
devices in the system.
This setting allows the operating system to change the
Yes
interrupt, I/O, and DMA settings. Set this option if the system
is running Plug and Play aware operating systems.
PCI Latency Timer [64]
Use the PCI Latency Timer option to specify the PCI latency time. The latency time is
measured in units of PCI clock cycles for the PCI device latency timer register.
Configuration options are:
32
64
Default
96
128
160
192
224
248
Allocate IRQ to PCI VGA [Yes]
Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA
adapter card an interrupt address.
Yes
No
DEFAULT
Assigns an IRQ to a PCI VGA card if card requests IRQ
Does not assign IRQ to a PCI VGA card even if the card
requests an IRQ
Page 116
PPC-5190 Flat Panel PC
Palette Snooping [Disabled]
Use the Palette Snooping option to enable or disable the palette snooping function.
Disabled
DEFAULT
Unless the VGA card manufacturer requires palette
snooping to be enabled, this option should be disabled.
PCI devices are informed that an ISA based Graphics
Enabled
device is installed in the system so the ISA based
Graphics card functions correctly. This does not
necessarily indicate a physical ISA adapter card. The
graphics chipset can be mounted on a PCI card. Always
check with the adapter card manual first, before
modifying the default settings in the BIOS.
PCI IDE BusMaster [Disabled]
Use the PCI IDE BusMaster BIOS option to enable or prevent PCI IDE busmastering.
Disabled
DEFAULT
Busmastering is prevented
IDE controller on the PCI local bus has mastering
Enabled
capabilities
OffBoard PCI/ISA IDE Card [Auto]
Use the OffBoard PCI/ISA IDE Card BIOS option to select the OffBoard PCI/ISA IDE
Card.
Auto
DEFAULT
The location of the Off Board PCI IDE adapter card is
automatically detected by the AMIBIOS.
Page 117
PPC-5190 Flat Panel PC
PCI Slot 1 is selected as the location of the OffBoard
PCI Slot 1
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 1.
PCI Slot 2 is selected as the location of the OffBoard
PCI Slot 2
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 2.
PCI Slot 3 is selected as the location of the OffBoard
PCI Slot 3
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 3.
PCI Slot 4 is selected as the location of the OffBoard
PCI Slot 4
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 4.
PCI Slot 5 is selected as the location of the OffBoard
PCI Slot 5
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 5.
PCI Slot 6 is selected as the location of the OffBoard
PCI Slot 6
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 6.
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
Reserved
The specified IRQ is reserved for use by Legacy ISA
devices
Page 118
PPC-5190 Flat Panel PC
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
Reserved
The specified DMA is reserved for use by Legacy
ISA devices
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Page 119
PPC-5190 Flat Panel PC
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that should
be reserved for legacy ISA devices.
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
64KB reserved for legacy ISA devices
5.5 Boot
Use the Boot menu (BIOS Menu 15) to configure system boot options.
BIOS Menu 15: Boot
Page 120
PPC-5190 Flat Panel PC
5.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced system
boot options.
BIOS Menu 16: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Page 121
PPC-5190 Flat Panel PC
Disabled
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Enabled
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
PS/2 Mouse Support [Auto]
Use the PS/2 Mouse Support option adjusts PS/2 mouse support capabilities.
Page 122
PPC-5190 Flat Panel PC
PS/2 mouse support is disabled and prevented from
Disabled
using system resources.
Allows the system to use a PS/2 mouse.
Enabled
Auto
DEFAULT
The system auto-adjusts PS/2 mouse support.
5.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 17) to specify the boot sequence from the
available devices. Possible boot devices may include:
1st FLOPPY DRIVE
HDD
CD/DVD
BIOS Menu 17: Boot Device Priority Setting
Page 123
PPC-5190 Flat Panel PC
5.5.3 Removable Drives
Use the Removable Drives menu (BIOS Menu 18) to specify the boot sequence of the
available FDDs. When the menu is opened, the FDDs connected to the system are listed
as shown below:
1st Drive
[1st FLOPPY DRIVE]
NOTE:
Only the drives connected to the system are shown. For example, if only
one FDD is connected only “1st Drive” is listed.
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available FDDs is shown. Select the first FDD the system boots from. If
the “1st Drive” is not used for booting this option may be disabled.
BIOS Menu 18: Removable Drives
Page 124
PPC-5190 Flat Panel PC
5.6 Security
Use the Security menu (BIOS Menu 19) to set system and user passwords.
BIOS Menu 19: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears next
to Change Supervisor Password.
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
Page 125
PPC-5190 Flat Panel PC
5.7 Chipset
Use the Chipset menu (BIOS Menu 20) to access the NorthBridge and SouthBridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
BIOS Menu 20: Chipset
Page 126
PPC-5190 Flat Panel PC
5.7.1 NorthBridge Configuration
Use the NorthBridge Configuration menu (BIOS Menu 21) to configure the northbridge
chipset.
BIOS Menu 21: NorthBridge Chipset Configuration
DRAM Frequency [Auto]
Use the DRAM Frequency option to specify the DRAM frequency or allow the system to
automatically detect the DRAM frequency.
200MHz
Sets the DRAM frequency to 200MHz
266MHz
Sets the DRAM frequency to 266MHz
333MHz
Sets the DRAM frequency to 333MHz
Auto
DEFAULT
Automatically selects the DRAM frequency
Page 127
PPC-5190 Flat Panel PC
Configure DRAM Timing by SPD [Enabled]
Use the Configure DRAM Timing by SPD option to determine if the system uses the SPD
(Serial Presence Detect) EEPROM to configure the DRAM timing. The SPD EEPROM
contains all necessary DIMM specifications including the speed of the individual
components such as CAS and bank cycle time as well as valid settings for the module and
the manufacturer's code. The SPD enables the BIOS to read the spec sheet of the DIMMs
on boot-up and then adjust the memory timing parameters accordingly.
DRAM timing parameters are manually set using the
Disabled
DRAM sub-items
Enabled
DEFAULT
DRAM timing parameter are set according to the
DRAM Serial Presence Detect (SPD)
If the Configure DRAM Timing by SPD option is disabled, the following configuration
options appear.
DRAM CAS# Latency [3]
DRAM RAS# to CAS# Delay [5 DRAM Clocks]
DRAM RAS# Precharge [5 DRAM Clocks]
DRAM RAS# Activate to Precha [15 DRAM Clocks]
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see if
it is necessary to reserve the space.
Disabled
15MB – 16MB
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
ISA expansion cards
Page 128
PPC-5190 Flat Panel PC
Init. Graphic Adapter Priority [PCI/Int-VGA]
The Init. Graphic Adapter Priority option selects the graphics controller the system uses as
a primary boot device. The options are:
Internal VGA
PCI/Int-VGA
DEFAULT
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory that
can be used by the Internal graphics device.
Disable
Enable, 1MB
1MB of memory used by internal graphics device
Enable, 4MB
4MB of memory used by internal graphics device
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
Enable, 16MB
16MB of memory used by internal graphics device
Enable, 32MB
32MB of memory used by internal graphics device
Graphics Aperture Size [64MB]
The Graphics Aperture Size option selects the size of the AGP aperture. The aperture is a
portion of the PCI memory address range dedicated as graphics memory address space.
64MB
128MB
DEFAULT
Graphics aperture size set as 64MB
Graphics aperture size set as 128MB
Page 129
PPC-5190 Flat Panel PC
Boot Display Device [CRT+LFP]
Use the Boot Display Device option to select the display device used by the system when
it boots. Configuration options are listed below.
CRT
LFP
CRT+LFP
DEFAULT
Flat Panel Type [640x480]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
640x480
800x600
1024x768 24bits
1280x1024
1400x1050
1024x768 18bits
1600x1200 48bits
800x600 24bits
800x600 18bits
1024x768 36bits
Page 130
DEFAULT
PPC-5190 Flat Panel PC
5.7.2 SouthBridge Configuration
The SouthBridge Configuration menu (BIOS Menu 22) the southbridge chipset to be
configured.
BIOS Menu 22: SouthBridge Chipset Configuration
OnBoard AC97 Audio [Auto]
Use the OnBoard AC97 Audio option to enable or disable the AC’97 CODEC.
Auto
Disabled
DEFAULT
The onboard AC’97 automatically detected and enabled
The onboard AC’97 is disabled
Page 131
PPC-5190 Flat Panel PC
5.8 Power
The Power menu (BIOS Menu 23) allows the advanced power management options to be
configured.
BIOS Menu 23: Power
Power Management/APM [Enabled]
Use the Power Management/APM BIOS option to enable access to the advanced power
management features. If this option is disabled, the only other option on the screen is the
Power Button Mode.
Disables the Advanced Power Management (APM)
Disabled
feature
Enabled
Page 132
DEFAULT
Enables the APM feature
PPC-5190 Flat Panel PC
Video Power Down Mode [Suspend]
The Video Power Down Mode BIOS option specifies in what system mode the video
device can be turned off.
The Video cannot be turned off in the Suspend or
Disabled
Standby mode
The video can be turned off in the Standby mode
Standby
Suspend
DEFAULT
The video can be turned off in the Suspend mode
Hard Disk Power Down Mode [Suspend]
The Hard Disk Power Down Mode BIOS specifies in what system mode the hard disk
device can be turned off.
The hard disk cannot be turned off in the Suspend or
Disabled
Standby mode
The hard disk can be turned off in the Standby mode
Standby
Suspend
DEFAULT
The hard disk can be turned off in the Suspend mode
Standby Time Out [Disabled]
The Power Management/APM option must be enabled in order to change this
configuration option. The Standby Time Out option specifies what length of time without
activity on certain components will place those components in a standby state. The
options are:
Disabled
DEFAULT
1 Min
2 Min
4 Min
8 Min
Page 133
PPC-5190 Flat Panel PC
10 Min
20 Min
30 Min
40 Min
50 Min
60 Min
Suspend Time Out [Disabled]
The Suspend Time Out option specifies what length of time without activity on certain
components will place those components in a suspended state. The options are listed
below:
Disabled
Default
1 Min
2 Min
4 Min
8 Min
10 Min
20 Min
30 Min
40 Min
50 Min
60 Min
Power Button Mode [On/Off]
Use the Power Button Mode BIOS to specify how the power button functions.
On/Off
DEFAULT
When the power button is pressed the system is either
turned on or off
Suspend
When the power button is pressed the system goes into
suspend mode
Page 134
PPC-5190 Flat Panel PC
Restore on AC Power Loss [Last State]
Use the Restore on AC Power Loss option to specify what state the system returns to if
there is a sudden loss of power to the system.
Power Off
The system remains turned off
Power On
The system turns on
Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Resume on Ring/LAN [Disabled]
The Resume on Ring/LAN BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the RI (ring in) modem line. That is,
the system will be roused by an incoming call on a modem.
Disabled
DEFAULT
Wake event not generated by an incoming call
Wake event generated by an incoming call
Enabled
Resume on PME# [Disabled]
The Resume on PME# BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the PCI PME (power management
event) controller.
Disabled
DEFAULT
Wake event not generated by PCI PME controller
activity
Enabled
Wake event generated by PCI PME controller activity
Page 135
PPC-5190 Flat Panel PC
Resume On RTC Alarm [Disabled]
Use the Resume On RTC Alarm option to specify the time the system should be roused
from a suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Enabled
If selected, the following appears with values that
can be selected:
RTC Alarm Date (Days)
System Time
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
Page 136
PPC-5190 Flat Panel PC
5.9 Exit
Use the Exit menu (BIOS Menu 24) to load default BIOS values, optimal failsafe values
and to save configuration changes.
BIOS Menu 24:Exit
Page 137
PPC-5190 Flat Panel PC
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options and
to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Page 138
PPC-5190 Flat Panel PC
Appendix
A
A IEI Panel PC
Product Line
Page 139
PPC-5190 Flat Panel PC
A.1 IEI Panel PC Products
A.1.1 Overview
IEI panel PC products are flexible, multi-functional flat panel PCs that can be applied in
diverse operational environments and implemented in multi-faceted applications. IEI panel
PC products come fully kitted with high-performance motherboards, CPUs, power supply
units and a host of other peripheral interface connectors. IEI panel PC products are
designed for ease of use and easy installation. This appendix introduces the full range of
IEI panel PC products.
A.1.2 IEI Panel PC Product Series
There are currently four panel PC product series. The four series are listed below.
PPC-27 Series
PPC-37 Series
PPC-51 Series
PPC-52 Series
PPC-53 Series
A.2 Panel PC Product Solutions
The different IEI panel PC product solutions are listed below. For further information,
please contact an IEI distributor, reseller, vendor or IEI sales representative. Please also
visit the IEI website (www.ieiworld.com).
A.2.1 PPC-27 Series Panel PC Solutions
All the models listed in the table below support an AMD® Geode® LX800 500MHz CPU.
Model
PPC-2706GS
PPC-2708GS
LCD Size
6.5” TFT LCD
8.4” TFT LCD
Max. Resolution
640 x 480
800 x 600
Brightness
400 cd/m2
220 cd/m2
LCD Color
262K
262K
Page 140
PPC-5190 Flat Panel PC
Model
PPC-2706GS
PPC-2708GS
Viewing Angle
120/100
120/100
Backlight MTBF
50000hrs
20000hrs
SBC Model
WAFER-LX800
WAFER-LX800
CPU
AMD LX800
AMD LX800
RAM
1 x DDR 333/400MHz
1 x DDR 333/400MHz
SO DIMM socket up to
SO DIMM socket up to 1GB
1GB
I/O Ports
1 x RS-232
2 x RS-232
2 x USB 2.0
2 x USB 2.0
1 x PS/2
1 x PS/2
1 x VGA out
1 x VGA out
2 x LAN
2 x LAN
1 x Audio
3 x Audio
1 x IDE
1 x IDE
2 x SATA
2 x SATA
SSD
CF Type II
CF Type II
HDD Drive Bay
1 x 2.5” SATA/IDE HDD
1 x 2.5” SATA/IDE HDD
Power Supply
60W AC Adapter
60W AC Adapter
Mounting
Stand/Rack/Wall/
Stand/Rack/Wall/
Panel/Arm/Din
Panel/Arm/Din
183 x 143 x 62.6
244 x 178 x 67
Weight
1.4/3.4kg
2.2/4.4kg
Front Panel Protection
IP 65 compliant
IP 65 compliant
Touch Screen
Resistive Type 4-wire
Resistive Type 4-wire
with RS-232 Interface
with RS-232 Interface
Dimension (WxDxH)
mm
Table A-1: PPC-27 Series Panel PC Solutions
A.2.2 PPC-37 Series Panel PC Solutions
All the models listed in the table below support Intel® Pentium® M / Celeron ® M /
ULV Celeron® M 1GHz/800MHz CPUs.
Page 141
PPC-5190 Flat Panel PC
Model
PPC-3708GS
PPC-3710GS
PPC-3712GS
PPC-3715GS
PPC-3717GS
LCD Size
8.4” TFT LCD
10.4” TFT LCD
12.1” TFT LCD
15” TFT LCD
17” TFT LCD
Max. Resolution
800 x 600
800 x 600
800 x 600
1024 x 786
1280 x 1024
Brightness
220 cd/m2
230 cd/m2
400 cd/m2
350 cd/m2
300 cd/m2
LCD Color
262K
262K
262K
262K
16.2M
Viewing Angle
120/100
120/100
140/110
120/100
140/130
Backlight MTBF
20000hrs
50000hrs
50000hrs
50000hrs
50000hrs
SBC Model
NANO-8522
NANO-8522
NANO-8522
ENANO-6612
ENANO-6612
(Socket 479/
(Socket 479/
(Socket 479/
(Socket 479/
(Socket 479/
BGA On-board)
BGA On-board)
BGA On-board)
BGA On-board)
BGA On-board)
Pentium® M /
Pentium® M /
Pentium® M /
Pentium® M /
Pentium® M /
Celeron® M /
Celeron® M /
Celeron® M /
Celeron® M /
Celeron® M /
ULV Celeron®
ULV Celeron®
ULV Celeron®
ULV Celeron®
ULV Celeron®
M
M
M
M 1GHz
M 1GHz
1GHz/800MHz
1GHz/800MHz
1GHz/800MHz
1 x DDR
1 x DDR
1 x DDR
1 x DDR
1 x DDR
266/200MHz
266/200MHz
266/200MHz
333/400MHz
333/400MHz
SO DIMM
SO DIMM
SO DIMM
SO DIMM
SO DIMM
socket
socket
socket
socket
socket
up to 1GB
up to 1GB
up to 1GB
up to 1GB
up to 1GB
1 x RS-232/
1 x RS-232/
1 x RS-232/
1 x RS-232/
1 x RS-232/
422/485
422/485
422/485
422/485
422/485
2 x RS-232
2 x RS-232
3 x RS-232
1 x RS-232
1 x RS-232
4 x USB 2.0
4 x USB 2.0
4 x USB 2.0
4 x USB 2.0
4 x USB 2.0
1 x PS/2
1 x PS/2
1 x PS/2
1 x PS/2
1 x PS/2
N/A
N/A
1 x LPT
1 x LPT
1 x LPT
1 x VGA out
1 x VGA out
1 x VGA out
1 x VGA out
1 x VGA out
1 x LAN
1 x LAN
1 x LAN
1 x LAN
1 x LAN
3 x Audio
3 x Audio
3 x Audio
3 x Audio
3 x Audio
1 x IDE
1 x IDE
1 x IDE
1 x IDE
1 x IDE
2 x SATA
2 x SATA
2 x SATA
2 x SATA
2 x SATA
SSD
CF Type II
CF Type II
CF Type II
CF Type II
CF Type II
Expansion Slot
N/A
N/A
N/A
1 x PCI
1 x PCI
HDD Drive Bay
1 x 2.5”
1 x 2.5”
1 x 2.5”
1 x 3.5”
1 x 3.5”
CPU
RAM
I/O Ports
Page 142
PPC-5190 Flat Panel PC
Model
PPC-3708GS
PPC-3710GS
PPC-3712GS
PPC-3715GS
PPC-3717GS
SATA/IDE HDD
SATA/IDE HDD
SATA/IDE HDD
Removable
Removable
SATA/IDE
SATA/IDE
HDD,
HDD,
1 x 2.5”
1 x 2.5”
SATA/IDE HDD
SATA/IDE HDD
FDD Drive Bay
N/A
N/A
N/A
1 x Slim FDD
1 x Slim FDD
CD-ROM
N/A
N/A
1 x Slim
1 x Slim
1 x Slim
CD-ROM
CD-ROM
CD-ROM
Drive Bay
Power Supply
80W/55W
80W/55W
80W/55W
150W
150W
AC Adapter
AC Adapter
AC Adapter
ATX Power
ATX Power
Stand/Rack/
Stand/Rack/
Stand/Rack/
Stand/Rack/
Stand/Rack/
Wall/Panel/
Wall/Panel/
Wall/Panel/
Wall/Panel/
Wall/Panel/
Arm
Arm
Arm
Arm
Arm
Dimension
244 x 178 x
311.5 x 242 x
340 x 260 x
410 x 309 x
452 x 356 x
(WxDxH) mm
75.2
72.8
73.4
80
80
Weight
2.2/4.4kg
3.4/5.8kg
6/8kg
8/12kg
TBD
Front Panel
IP 65
IP 65
IP 65
IP 65
IP 65
Protection
compliant
compliant
compliant
compliant
compliant
Touch Screen
Resistive Type
Resistive Type
Resistive Type
Resistive Type
Resistive Type
5-wire with
5-wire with
5-wire with
5-wire with
5-wire with
RS-232
RS-232
RS-232
RS-232
RS-232
Interface
Interface
Interface
Interface
Interface
Mounting
Table A-2: PPC-37 Series Panel PC Solutions
A.2.3 PPC-51 Series Panel PC Solutions
All the models listed in the table below support Intel® Pentium® 4 / Celeron® D CPUs up
to 2.8GHz.
Model
PPC-5150GS
PPC-5170GS
PPC-5190GS
LCD Size
15” TFT LCD
17” TFT LCD
19” TFT LCD
Max.
1024 x 786
1280 x 1024
1280 x 1024
Page 143
PPC-5190 Flat Panel PC
Model
PPC-5150GS
PPC-5170GS
PPC-5190GS
Brightness
350 cd/m2
300 cd/m2
300 cd/m2
LCD Color
262K
16.2M
16.2M
Viewing Angle
120/100
140/130
140/130
Backlight
50000hrs
50000hrs
50000hrs
POS-8520
POS-8520
POS-8520
(Socket 478)
(Socket 478)
(Socket 478)
Pentium® 4 /
Pentium® 4 /
Pentium® 4 /
Celeron ® D
Celeron ® D
Celeron ® D
2 x DDR 266/333MHz
2 x DDR 266/333MHz
2 x DDR 266/333MHz
DIMM socket up to 2GB
DIMM socket up to 2GB
DIMM socket up to 2GB
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
4 x RS-232
4 x RS-232
4 x RS-232
4 x USB 2.0
6 x USB 2.0
6 x USB 2.0
2 x PS/2
2 x PS/2
2 x PS/2
1 x LPT
1 x LPT
1 x LPT
1 x VGA out
1 x VGA out
1 x VGA out
2 x LAN
2 x LAN
2 x LAN
3 x Audio
3 x Audio
3 x Audio
2 x IDE
2 x IDE
2 x IDE
2 x SATA
2 x SATA
2 x SATA
SSD
CF Type II
CF Type II
CF Type II
Expansion Slot
1 x PCI
1 x PCI
1 x PCI
HDD Drive Bay
1 x 2.5” SATA/IDE HDD
1 x 2.5” SATA/IDE HDD
1 x 2.5” SATA/IDE HDD
w/ Anti-Shock or 2 x
w/ Anti-Shock or 2 x
w/ Anti-Shock or 2 x
2.5”
2.5”
2.5”
SATA/IDE HDD
SATA/IDE HDD
SATA/IDE HDD
w/o Anti-Shock
w/o Anti-Shock
w/o Anti-Shock
FDD Drive Bay
1 x Slim FDD
1 x Slim FDD
1 x Slim FDD
CD-ROM
1 x Slim CD-ROM
1 x Slim CD-ROM
1 x Slim CD-ROM
180W ATX Power
180W ATX Power
180W ATX Power
Resolution
MTBF
SBC Model
CPU
RAM
I/O Ports
Drive Bay
Power Supply
Page 144
PPC-5190 Flat Panel PC
Model
PPC-5150GS
PPC-5170GS
PPC-5190GS
Mounting
Stand/Rack/
Stand/Rack/
Stand/Rack/
Wall/Panel/Arm
Wall/Panel/Arm
Wall/Panel/Arm
410 x 309 x 110
452 x 356 x 110
482 x 399 x 110
Weight
7/11kg
8/12kg
12.6/18.2kg
Front Panel
IP 65 compliant
IP 65 compliant
IP 65 compliant
Resistive Type 5-wire
Resistive Type 5-wire
Resistive Type 5-wire
with RS-232 Interface
with RS-232 Interface
with RS-232 Interface
Dimension
(WxDxH) mm
Protection
Touch Screen
Table A-3: PPC-51 Series Panel PC Solutions
A.2.4 PPC-52 Series Panel PC Solutions
All the models listed in the table below support Intel® Pentium® 4 / Celeron® D CPUs up
to 3.8GHz.
Model
PPC-5150GS
PPC-5170GS
PPC-5190GS
LCD Size
15” TFT LCD
17” TFT LCD
19” TFT LCD
Max.
1024 x 786
1280 x 1024
1280 x 1024
Brightness
300 cd/m2
300 cd/m2
300 cd/m2
LCD Color
262K
16.2M
16.2M
Viewing Angle
120/100
140/130
140/130
Backlight
30000hrs
30000hrs
30000hrs
POS-6614
POS-6614
POS-6614
(LGA-775)
(LGA-775)
(LGA-775)
Pentium® 4 /
Pentium® 4 /
Pentium® 4 /
Celeron ® D
Celeron ® D
Celeron ® D
2 x DDR 400MHz
2 x DDR 400MHz
2 x DDR 400MHz
DIMM socket up to 2GB
DIMM socket up to 2GB
DIMM socket up to 2GB
1 x RS-232/422/485
1 x RS-232/422/485
1 x RS-232/422/485
Resolution
MTBF
SBC Model
CPU
RAM
I/O Ports
Page 145
PPC-5190 Flat Panel PC
Model
PPC-5150GS
PPC-5170GS
PPC-5190GS
3 x RS-232
3 x RS-232
3 x RS-232
4 x USB 2.0
6 x USB 2.0
6 x USB 2.0
2 x PS/2
2 x PS/2
2 x PS/2
1 x LPT
1 x LPT
1 x LPT
1 x VGA out
1 x VGA out
1 x VGA out
2 x LAN
2 x LAN
2 x LAN
3 x Audio
3 x Audio
3 x Audio
2 x IDE
2 x IDE
2 x IDE
2 x SATA
2 x SATA
2 x SATA
SSD
CF Type II
CF Type II
CF Type II
Expansion Slot
1 x PCI, 1 x PCIe
1 x PCI, 1 x PCIe
1 x PCI, 1 x PCIe
HDD Drive Bay
2 x 3.5” SATA/IDE HDD
2 x 3.5” SATA/IDE HDD
2 x 3.5” SATA/IDE HDD
w/ Anti-Shock
w/ Anti-Shock
w/ Anti-Shock
FDD Drive Bay
1 x Slim FDD
1 x Slim FDD
1 x Slim FDD
CD-ROM
1 x Slim CD-ROM
1 x Slim CD-ROM
1 x Slim CD-ROM
Power Supply
250W ATX Power
250W ATX Power
250W ATX Power
Mounting
Stand/Rack/
Stand/Rack/
Stand/Rack/
Wall/Panel/Arm
Wall/Panel/Arm
Wall/Panel/Arm
TBD
TBD
TBD
Weight
TBD
TBD
TBD
Front Panel
IP 65 compliant
IP 65 compliant
IP 65 compliant
Resistive Type 5-wire
Resistive Type 5-wire
Resistive Type 5-wire
with RS-232 Interface
with RS-232 Interface
with RS-232 Interface
Drive Bay
Dimension
(WxDxH) mm
Protection
Touch Screen
Table A-4: PPC-52 Series Panel PC Solutions
A.2.5 PPC-53 Series Panel PC Solutions
All the models listed in the table below support Intel® Pentium® M / Celeron ® M /
ULV Celeron® M 1GHz/800MHz CPUs.
Page 146
PPC-5190 Flat Panel PC
Model
PPC-5350GS
LCD Size
15” TFT LCD
Max. Resolution
1024 x 786
Brightness
350 cd/m2
LCD Color
262K
Viewing Angle
120/100
Backlight MTBF
50000hrs
SBC Model
A-300 (Socket 479)
CPU
Pentium® M /
Celeron ® M /
ULV Celeron® M 1GHz/800MHz
RAM
2 x DDR 266/333MHz
DIMM socket up to 2GB
I/O Ports
1 x RS-232/422/485
4 x RS-232
4 x USB 2.0
2 x PS/2
1 x LPT
1 x VGA out
1 x DVI
2 x LAN
3 x Audio
2 x IDE
2 x SATA
SSD
CF Type II
Expansion Slot
1 x PCI
1 x mini-PCI
1 x PCMCIA supports 32bit
Cardbus
HDD Drive Bay
1 x 2.5” SATA/IDE HDD
CD-ROM
1 x Slim CD-ROM
Drive Bay
Power Supply
150W ATX Power
Mounting
Stand/Rack/
Page 147
PPC-5190 Flat Panel PC
Model
PPC-5350GS
Wall/Panel/Arm
Dimension (WxDxH) mm
410 x 309 x 110
Weight
8/12kg
Front Panel Protection
IP 65 compliant
Touch Screen
Resistive Type 5-wire
with RS-232 Interface
Table A-5: PPC-53 Series Panel PC Solutions
Page 148
PPC-5190 Flat Panel PC
Appendix
B
B Interface Connectors
Page 149
PPC-5190 Flat Panel PC
The PPC-5190 flat panel PC POS-8520 motherboard comes with a number of peripheral
interface connectors and configuration jumpers listed in Chapter 2. The pinouts for these
connectors are listed below.
B.1 Floppy Disk Drive Connector
POS-8520 board is equipped with a 34-pin daisy-chain driver connector cable.
PIN
Description
PIN
Description
1
GROUND
2
REDUCE WRITE
3
GROUND
4
N/C
5
GROUND
6
N/C
7
GROUND
8
INDEX#
9
GROUND
10
MOTOR ENABLE A#
11
GROUND
12
DRIVE SELECT B#
13
GROUND
14
DRIVE SELECT A#
15
GROUND
16
MOTOR ENABLE B#
17
GROUND
18
DIRECTION#
19
GROUND
20
STEP#
21
GROUND
22
WRITE DATA#
23
GROUND
24
WRITE GATE#
25
GROUND
26
TRACK 0#
27
GROUND
28
WRITE PROTECT#
29
GROUND
30
READ DATA#
31
GROUND
32
SIDE 1 SELECT#
33
GROUND
34
DISK CHANGE#
Page 150
PPC-5190 Flat Panel PC
B.2 PCIe - IDE Disk Drive Connector
Four IDE (Integrated Device Electronics) hard disk drives can be attached to the
POS-8520 IDE controller.
IDE1, IDE2: Primary, Secondary IDE Connector
PIN
Description
PIN
Description
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
N/C
21
IDE DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
IDE CHRDY
28
GND
29
IDE DACK
30
GND
31
INTERRUPT
32
N/C
33
SA 1
34
N/C
35
SA 0
36
SA 2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GND
Page 151
PPC-5190 Flat Panel PC
B.3 Parallel Port
This port is usually connected to printer. The POS-8520 includes one on-board parallel
port, accessed through 25-pin D-type female connector LPT1.
LPT1: (LPT1 DB-25 Female) Parallel Port Connector
PIN
Description
PIN
Description
1
STROBE#
2
DATA 0
3
DATA 1
4
DATA 2
5
DATA 3
6
DATA 4
7
DATA 5
8
DATA 6
9
DATA 7
10
ACKNOWLEDGE
11
BUSY
12
PAPER EMPTY
13
PRINTER SELECT
14
AUTO FORM FEED #
15
ERROR#
16
INITIALIZE
17
PRINTER SELECT LN#
18
GND
19
GND
20
GND
21
GND
22
GND
23
GND
24
GND
25
GND
Page 152
PPC-5190 Flat Panel PC
B.4 Serial Ports
The POS-8520 offers six high speed NS16C550 compatible UARTs with Read/Receive 16
byte FIFO serial port (COM1/COM2/COM3/COM4/COM5/COM6)
COM1: Serial Port 2x5 pin header Connector
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
CN20A: Serial Port DB-9 Male Connector (COM1)
PIN
Description
1
DATA CARRIER DETECT (DCD)
2
RECEIVE DATA (RXD)
3
TRANSMIT DATA (TXD)
4
DATA TERMINAL READY (DTR)
5
GROUND (GND)
6
DATA SET READY (DSR)
7
REQUEST TO SEND (RTS)
8
CLEAR TO SEND (CTS)
9
RING INDICATOR (RI)
COM2: Serial Port 2 x 5 Pin Header Connector
COM2 Support three modes: RS-232, RS-422 and RS-485 (via 2 x 5 pin box header
connector).
Page 153
PPC-5190 Flat Panel PC
RS-232 Mode
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
RS-422 Mode
PIN
Description
PIN
Description
1
TXD-
2
RX-
3
TXD+
4
RX+
5
NC
6
NC
7
NC
8
Voltage
9
NC
10
NC
RS-485 Mode
PIN
Description
PIN
Description
1
RTX-
2
NC
3
RTX+
4
NC
5
NC
6
NC
7
NC
8
Voltage
9
NC
10
NC
CN20B: Serial Port DB-9 Male Connector (COM2)
COM2 supports three modes: RS-232, RS-422 and RS-485 (via DB-9 Connector).
Page 154
PPC-5190 Flat Panel PC
RS-232 Mode
PIN
Description
PIN
Description
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTX
4
DTR
9
RI
5
GND
RS-422 Mode
PIN
Description
PIN
Description
1
TXD-
6
RX-
2
TXD+
7
RX+
3
NC
8
NC
4
NC
9
Voltage
5
NC
RS-485 Mode
PIN
Description
PIN
Description
1
RTX-
6
NC
2
RTX+
7
NC
3
NC
8
NC
4
NC
9
Voltage
5
NC
Page 155
PPC-5190 Flat Panel PC
COM3: Serial Port 2x5 Pin Header Connector
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
COM4: Serial Port 2x5 Pin Header Connector
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
Page 156
PPC-5190 Flat Panel PC
CN22: Serial Port DB-9 Male Connector (COM4)
PIN
Description
1
DATA CARRIER DETECT (DCD)
2
RECEIVE DATA (RXD)
3
TRANSMIT DATA (TXD)
4
DATA TERMINAL READY (DTR)
5
GROUND (GND)
6
DATA SET READY (DSR)
7
REQUEST TO SEND (RTS)
8
CLEAR TO SEND (CTS)
9
RING INDICATOR (RI)
COM5: Serial Port 2x5 Pin Header Connector
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
COM6: Serial Port 2x5 Pin Header Connector
PIN
Description
PIN
Description
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTX
7
DTR
8
RI
9
GND
10
NC
Page 157
PPC-5190 Flat Panel PC
B.5 Keyboard / Mouse Connector
The POS-8520 provides one keyboard and one mouse box header connector, as well as
external PS/2 keyboard and mouse connectors.
CN23A (Purple): Extended Keyboard 6-pin Mini Din Connector
PIN
Description
1
KB DATA
2
NC
3
GND
4
VCC
5
KB CLOCK
6
NC
CN23B (Green): Extended Mouse 6-pin Mini Din Connector
PIN
Description
1
MS DATA
2
NC
3
GND
4
VCC
5
MS CLOCK
6
NC
CN16: 5-pin Header Keyboard Connector
PIN
Description
1
KB CLOCK
2
KB DATA
3
N/C
4
GND
5
+5V
Page 158
PPC-5190 Flat Panel PC
CN15: PS/2 Mouse 5-pin Header Connector
PIN
Description
1
MS CLOCK
2
MS DATA
3
N/C
4
GND
5
+5V
B.6 External Switches and Indicators
CN8: Multi Panel
PIN
Description
PIN
Description
1
SPEAKER
11
POWER-VCC
2
N/C
12
N/C
3
N/C
13
GND
4
+5V
14
KEYLOCK
5
RESET SW
15
GND
6
GND
16
GND
7
IDE LED -
17
N/C
8
IDE LED+
18
ATX POWER CONTROL
9
ATX POWER BUTTON
19
ATX 5VSB
10
GND
20
ATX 5VSB
Page 159
PPC-5190 Flat Panel PC
B.7 USB Port Connector
The POS-8520 has eight built-in USB ports for the future I/O bus expansion.
CN26, CN27, CN28: 8-PIN Header USB Connectors
PIN
Description
1
8
VCC
3
6
USBD0-
5
4
USBD0+
7
2
GND
CN25: 2 External USB Connectors
PIN
Description
1
5
VCC
2
6
USBD0-
3
7
USBD0+
4
8
GND
Page 160
PPC-5190 Flat Panel PC
B.8 IrDA Infrared Interface Port
The POS-8520 has a built-in IrDA port that supports Serial Infrared (SIR) or Amplitude
Shift Keyed IR (ASKIR) interfaces. To use the IrDA port, configure the FIR or ASKIR
model in the Peripheral Setup COM2 in BIOS.
Then the normal RS-232 COM2 will be
disabled.
IR1: IrDA Connector
PIN
Description
1
+5V
2
NC
3
IR-RX
4
GND
5
IR-TX
6
+5V
Page 161
PPC-5190 Flat Panel PC
B.9 VGA Connector
The POS-8520 provides one DB-15 female connector and one built-in 10-pin VGA box
header connector that can be connected directly to a monochrome CRT monitor as well as
high resolution color CRT monitor.
VGA1: DB-15 Female VGA Connector
PIN
Description
PIN
Description
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
N/C
12
DDC DAT
13
HSYNC
14
VSYNC
15
DDC CLK
CN14: 10-pin Header VGA Connector
PIN
Description
PIN
Description
1
RED
2
SMCLK
3
GREEN
4
SMDATA
5
BLUE
6
GND
7
H-SYNC
8
GND
9
V-SYNC
10
GND
Page 162
PPC-5190 Flat Panel PC
B.10 LAN RJ45 Connector
The POS-8520 is equipped with two Gigabit Ethernet Controller RTL8110SC chipsets and
two GbE LAN RJ-45 connectors.
CN31: Dual LAN RJ45 Connector
PIN
Description
PIN
Description
1
TX+ (or MDX0+)
5
N/C (or MDX2-)
2
TX- (or MDX0-)
6
RX- (or MDX1-)
3
RX+ (or MDX1+)
7
N/C (or MDX3+)
4
N/C (or MDX2+)
8
N/C (or MDX3-)
13
MDX0+
17
MDX2-
14
MDX0-
18
MDX1-
15
MDX1+
19
MDX3+
16
MDX2+
20
MDX3-
B.11 Fan Connector
The POS-8520 provides three CPU cooling and system fan connectors. The CPU cooling
fan has a linear fan speed controlled by the BIOS. These connectors can supply
12V/500mA to the cooling fans.
FAN1: CPU Fan Connector
PIN
Description
1
GND
2
Linear control
3
Fan Sensor
Page 163
PPC-5190 Flat Panel PC
FAN2: System Fan Connector
PIN
Description
1
GND
2
+12V
3
Fan Sensor
FAN3: System Fan Connector
PIN
Description
1
GND
2
+12V
3
Fan Sensor
B.12 Inverter (LCD Backlight) Connector
CN12: Inverter (LCD Backlight) Connector
PIN
Description
PIN
Description
1
NC
2
GND
3
+12V
4
GND
5
ENABKL
Page 164
PPC-5190 Flat Panel PC
B.13 LCD Panel LVDS Interface Connector
The POS-8520 provides up to 48-bit color TFT LCD.
CN30: DF13-30DP-1.25 LVDS Interface Connector
PIN
Description
PIN
Description
1
GND
2
GND
3
A0P
4
A0M
5
A1P
6
A1M
7
A2P
8
A2M
9
CLK1P
10
CLK1M
11
A3P
12
A3M
13
GND
14
GND
15
A4P
16
A4M
17
A5P
18
A5M
19
A6P
20
A6M
21
CLK2P
22
CLK2M
23
A7P
24
A7M
25
GND
26
GND
27
LCD_VDD
28
LCD_VDD
29
LCD_VDD
30
LCD_VDD
B.14 Audio Connectors
CN7: Audio CD IN (2.54mm)
PIN
Description
PIN
Description
1
CD IN_L
2
GND
3
GND
4
CD IN_R
Page 165
PPC-5190 Flat Panel PC
CN2: Audio LINE OUT (2.54mm)
PIN
Description
PIN
Description
1
LINEOUT_L
2
GND
3
GND
4
LINE OUT_R
CN24: Audio Jack
Color
Description
RED
MIC IN
BLUE
LINE IN
GREEN
SPEAK OUT
B.15 Digital Input / Output
CN6: Digital Input / Output
PIN
Description
PIN
Description
1
GND
2
+5V
3
Output 3
4
Output 2
5
Output 1
6
Output 0
7
Input 3
8
Input 2
9
Input 1
10
Input 0
Page 166
PPC-5190 Flat Panel PC
B.16 Compact Flash TYPE II Storage Card Socket
The POS-8520 configures Compact Flash TYPE II Storage Card in IDE Mode.
CF1: Compact Flash TYPE II Socket PIN Assignment
PIN
Description
PIN
Description
1
GROUND
26
CARD DETECT1
2
D3
27
D11
3
D4
28
D12
4
D5
29
D13
5
D6
30
D14
6
D7
31
D15
7
CS1#
32
CS3#
8
N/C
33
N/C
9
GROUND
34
IOR#
10
N/C
35
IOW#
11
N/C
36
OBLIGATORY TO PULL HIGH
12
N/C
37
IRQ15
13
VCC
38
VCC
14
N/C
39
MASTER/SLAVE
15
N/C
40
N/C
16
N/C
41
RESET#
17
N/C
42
IORDY
18
A2
43
N/C
19
A1
44
OBLIGATORY TO PULL HIGH
20
A0
45
ACTIVE#
21
D0
46
PDIAG#
22
D1
47
D8
23
D2
48
D9
24
N/C
49
D10
25
CARD DETECT2
50
GROUND
Page 167
PPC-5190 Flat Panel PC
B.17 ATX Power Connector
PW2 is a 20-pin ATX power supply connector with the following pin assignments.
PW2: ATX Power Supply Connector
PIN
Description
PIN
Description
11
3.3V
1
3.3V
12
-12V
2
3.3V
13
GND
3
GND
14
PS-ON
4
+5V
15
GND
5
GND
16
GND
6
+5V
17
GND
7
GND
18
-5V
8
Power good
19
+5V
9
5VSB
20
+5V
10
+12V
B.18 ATX 12V Power Connector
This connector supports ATX power. Functions such as modem Ring on, wake-up LAN
and soft power off are supported.
PW1: ATX-12V Power Connector
PIN
Description
PIN
Description
1
GND
2
GND
3
+12V
4
+12V
Page 168
PPC-5190 Flat Panel PC
NOTE:
The power from PW1 should support at least a 6.5A current for the P4 CPU. If
the power output is too low, the CPU may not function normally. Be sure the
power from the power supply is sufficient, and don’t share this power with other
devices, such as hard disk etc. Use IEI’s special ATX power connector cable for
connection to a power supply if the power supply doesn’t have a suitable ATX
connector cable.
B.19 Internal Switches and Indicators
S2: Reset Switch
PIN
1
Description
Reset
PIN
2
Description
GND
B.20 Serial ATA Connector
The POS-8520 provides two Serial ATA (SATA) ports.
SATA1, SATA2: Serial ATA Connector
PIN
Description
PIN
Description
1
S_TXP
3
S_RXN
2
S_TXN
4
S_RXP
Page 169
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 170
PPC-5190 Flat Panel PC
Appendix
C
C BIOS Configuration
Options
Page 171
PPC-5190 Flat Panel PC
C.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 5.
System Overview ...................................................................................................84
System Time [xx:xx:xx] .........................................................................................85
System Date [xx/xx/xx] ..........................................................................................85
Max CUPID Value Limit [Disabled] .......................................................................88
Hyper Threading Technology [Disabled] ............................................................88
IDE Configuration [P-ATA Only]...........................................................................89
S-ATA Running Enhanced Mode [Yes]................................................................90
P-ATA Channel Selection [Both] ..........................................................................90
S-ATA Ports Definition [PO-3rd./P1-4th.] ...............................................................90
Configure S-ATA as RAID [No].............................................................................91
Hard Disk Write Protect [Disabled] ......................................................................91
IDE Detect Time Out (Sec) [35] .............................................................................91
ATA (PI) 80Pin Cable Detection [Host & Device] ................................................92
IDE Master and IDE Slave .....................................................................................92
Auto-Detected Drive Parameters..........................................................................93
Type [Auto] .............................................................................................................94
ZIP ...........................................................................................................................94
LS-120 .....................................................................................................................94
LBA/Large Mode [Auto].........................................................................................94
Block (Multi Sector Transfer) [Auto] ....................................................................95
PIO Mode [Auto].....................................................................................................95
S.M.A.R.T [Auto].....................................................................................................96
32Bit Data Transfer [Disabled] .............................................................................96
Floppy A [1.44 MB 3½”].........................................................................................97
On Board Floppy Controller [Enabled] ................................................................98
Serial Port1 Address [3F8/IRQ4] ..........................................................................98
Serial Port2 Address [2F8/IRQ3] ..........................................................................99
Serial Port2 Mode [Normal]...................................................................................99
Page 172
PPC-5190 Flat Panel PC
Parallel Port Address [378] ...................................................................................99
Parallel Port Mode [Normal]............................................................................... 100
Parallel Port IRQ [IRQ7]...................................................................................... 101
Digital I/O Address [280h] .................................................................................. 101
Serial Port3 Address [3E8]................................................................................. 101
Serial Port3 IRQ [11] ........................................................................................... 102
Serial Port4 Address [2E8]................................................................................. 102
Serial Port4 IRQ [10] ........................................................................................... 102
Serial Port5 Address [2F0]................................................................................. 103
Serial Port5 IRQ [11] ........................................................................................... 103
Serial Port6 Address [2E0]................................................................................. 103
Serial Port6 IRQ [10] ........................................................................................... 104
H/W Health Function [Enabled] ......................................................................... 105
Suspend Mode [S1 (POS)] ................................................................................. 107
ACPI 2.0 Features [No] ....................................................................................... 109
ACPI APIC Support [Enabled] ........................................................................... 109
APIC ACPI SCI IRQ [Disabled]........................................................................... 110
AMI OEMB table [Enabled]................................................................................. 110
Headless Mode [Disabled] ................................................................................. 110
MPS Revision [1.4].............................................................................................. 111
Remote Access [Disabled]................................................................................. 112
Serial Port Number ............................................................................................. 112
Serial Port Mode.................................................................................................. 112
Flow Control ........................................................................................................ 112
Redirection after BIOS POST............................................................................. 112
Terminal Type...................................................................................................... 112
VT-UTF8 Combo Key Support ........................................................................... 112
USB Configuration.............................................................................................. 113
USB Devices Enabled......................................................................................... 113
USB Function [8 USB Ports].............................................................................. 114
Legacy USB Support [Disabled]........................................................................ 114
USB 2.0 Controller [Enabled]............................................................................. 114
Page 173
PPC-5190 Flat Panel PC
Plug & Play O/S [No]........................................................................................... 115
PCI Latency Timer [64] ....................................................................................... 116
Allocate IRQ to PCI VGA [Yes] .......................................................................... 116
Palette Snooping [Disabled] .............................................................................. 117
PCI IDE BusMaster [Disabled] ........................................................................... 117
OffBoard PCI/ISA IDE Card [Auto] .................................................................... 117
IRQ# [Available]................................................................................................ 118
DMA Channel# [Available] ................................................................................. 119
Reserved Memory Size [Disabled] .................................................................... 120
Quick Boot [Enabled] ......................................................................................... 121
Quiet Boot [Disabled] ......................................................................................... 121
AddOn ROM Display Mode [Force BIOS] ......................................................... 122
Bootup Num-Lock [On] ...................................................................................... 122
PS/2 Mouse Support [Auto] ............................................................................... 122
Change Supervisor Password........................................................................... 125
Change User Password...................................................................................... 125
DRAM Frequency [Auto] .................................................................................... 127
Configure DRAM Timing by SPD [Enabled] ..................................................... 128
Memory Hole [Disabled]..................................................................................... 128
Init. Graphic Adapter Priority [PCI/Int-VGA]..................................................... 129
Internal Graphics Mode Select [Enable, 8MB] ................................................. 129
Graphics Aperture Size [64MB] ......................................................................... 129
Boot Display Device [CRT+LFP] ....................................................................... 130
Flat Panel Type [640x480] .................................................................................. 130
OnBoard AC97 Audio [Auto] ............................................................................. 131
Power Management/APM [Enabled].................................................................. 132
Video Power Down Mode [Suspend] ................................................................ 133
Hard Disk Power Down Mode [Suspend] ......................................................... 133
Standby Time Out [Disabled]............................................................................. 133
Suspend Time Out [Disabled]............................................................................ 134
Power Button Mode [On/Off] ............................................................................. 134
Restore on AC Power Loss [Last State]........................................................... 135
Page 174
PPC-5190 Flat Panel PC
Resume on Ring/LAN [Disabled]....................................................................... 135
Resume on PME# [Disabled] ............................................................................. 135
Resume On RTC Alarm [Disabled].................................................................... 136
RTC Alarm Date (Days) ...................................................................................... 136
System Time........................................................................................................ 136
Save Changes and Exit ...................................................................................... 138
Discard Changes and Exit ................................................................................. 138
Discard Changes................................................................................................. 138
Load Optimal Defaults........................................................................................ 138
Page 175
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 176
PPC-5190 Flat Panel PC
Appendix
D
D Software Drivers
Page 177
PPC-5190 Flat Panel PC
D.1 Introduction
The touch panel controller enables analog resistive touch panels for four-wire, five-wire &
eight-wire models. The controller directly communicates with the PC system through the
touch panel communications interface. The controller design is superior in sensitivity,
accuracy, and friendly operation. The touch panel driver emulates the left mouse button
and the right mouse button functions.
The touch panel driver supports the following operating systems:
Microsoft Windows versions:
o
o
o
o
o
o
o
Microsoft Windows 95
Microsoft Windows 98
Microsoft Windows ME
Microsoft Windows 2000
Microsoft Windows NT
Microsoft Windows XP
Microsoft Windows XP Tablet PC Edition
Microsoft Windows CE versions:
o
o
o
Microsoft Windows CE 2.12
Microsoft Windows CE 3.0
Microsoft Windows CE. NET
Linux
IMac
DOS.
Driver installation is described below.
D.2 Driver Installation
To install the touch panel software driver, please follow the steps below.
Step 1: Insert the driver CD that came with the PPC-5190 into the CD drive.
Step 2: Once the CD drive is installed, the screen in Figure C-1 appears.
Page 178
PPC-5190 Flat Panel PC
Figure C-1: Driver CD Pop Up Screen
Step 3: Select the operating system installed on the system from the menu on the left
side of the screen.
NOTE:
The following description is for driver installation using a Windows 2000
OS. If a different OS is installed, please refer to the driver user manual for
the relevant OS. The driver user manuals can be accessed by selecting
“User Manual” from the menu on the left side of the “Driver CD Pop Up
Screen”.
Step 4: Once the OS system is selected, the touch kit setup will prepare the install shield
wizard (Figure C-2).
Page 179
PPC-5190 Flat Panel PC
Figure C-2: Install Shield Wizard Preparation
Step 5: After the Install Shield Wizard is ready, a welcome screen appears
(Figure C-3).
Figure C-3: Welcome Screen
Step 6: To continue the installation process click NEXT.
Step 7: An Install PS/2 interface driver screen appears (Figure C-4). It is not
necessary to install the PS/2 interface driver. To continue click NEXT.
Page 180
PPC-5190 Flat Panel PC
Figure C-4: Install PS/2 Interface Driver
Step 8: Four point calibration options are then selected. Four point calibrations can be
done every time a user boots up, during the next time the system boots or never.
Select when a four-point calibration should be done. Click NEXT to continue.
Page 181
PPC-5190 Flat Panel PC
Figure C-5: Install PS/2 Interface Driver
Step 9: The user is then prompted to ensure the touch monitor or the USB for the touch
controller is plugged into the system (Figure C-6). Once the touch controller is
plugged into the system, click OK.
Figure C-6: Touch Monitor/USB Touch Controller Confirmation
Step 10: The user is then prompted to select a file directory in which the touch kit
controller is installed (Figure C-7). The default directory is “C:\Program
Files\TouchKit.” If a different folder must be used, select browse and then
select the folder. Once the folder is selected, click Next to continue.
Page 182
PPC-5190 Flat Panel PC
Figure C-7: Controller Installation Directory
Step 11: The user is then prompted to select a file directory in which the program icons
are saved (Figure C-8). The default folder is “TouchKit.” If a different folder must
be used, select a folder from the list shown. Once the folder is selected, click
NEXT to continue.
Page 183
PPC-5190 Flat Panel PC
Figure C-8: Program Icon Directory
Step 12: The program then starts installing (Figure C-9).
Figure C-9: Installing
Page 184
PPC-5190 Flat Panel PC
Step 13: Once the program is finished installing, the user is prompted to restart the
computer now or to restart the computer later (Figure C-10). Select when the
computer should be restarted and click FINISH to complete the driver installation
procedure.
Figure C-10: Installation Complete
D.3 Touch Panel Driver Configuration
To configure the touch panel driver options, refer to the TouchKit user manual located on
the driver installation CD.
Page 185
PPC-5190 Flat Panel PC
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 186
PPC-5190 Flat Panel PC
E Index
Page 187
PPC-5190 Flat Panel PC
A
E
embedded system solutions ................... 140
Applications ...............................................20
Arm Mounting ............................................65
ATX 12V Power Connector......................168
Ethernet Connection ..................................66
External Peripheral Device Connectors.....42
External Switches and Indicators............ 159
ATX Power Connector .............................168
Audio Connectors ....................................165
F
Audio Port Connection...............................67
Fan Connector ........................................ 163
B
FDD Installation .........................................54
Features.....................................................21
Back Cover Removal .................................71
BIOS ..........................................................81
Flat Panel Screen ......................................29
Floppy Disk Drive Connector .................. 150
BIOS Configuration..................................171
C
G
Graphics Support.......................................38
CD Drive Installation ..................................55
CF Card Setup...........................................49
H
Cleaning Tools .............................................5
Clear CMOS Setup ....................................49
HDD Installation .........................................53
COM port RI and Voltage Selection...........50
COM2 Port RS232/422/485 Selection.......50
Compact Flash Socket.............................167
Conventions.................................................7
Cooling Fan Replacement .........................78
CPU Support..............................................36
D
I
Installation and Configuration ....................43
Internal Overview .......................................25
Internal Peripheral Device Connectors......40
Internal Slots ..............................................40
Inverter (LCD Backlight) Connector........ 164
IrDA Infrared Interface Port..................... 161
Detaching the Elevated Platform ...............72
Digital Input / Output ................................166
Dimensions ................................................33
DIMM Replacement ...................................74
Page 188
J
Jumper Settings .........................................46
PPC-5190 Flat Panel PC
K
PCI E-IDE Disk Drive Connector ............ 151
Power Supply.............................................30
Keyboard / Mouse Connector..................158
Preinstalled Components...........................44
Keyboard and Mouse Connection .............67
Preinstalled Hardware Components ..........26
Keyboard and Mouse Power Setting .........52
PSU Module Replacement ........................75
L
S
LAN RJ45 Connector...............................163
Safety Precautions.......................................3
LCD Panel Connection ..............................66
Serial ATA Connector .............................. 169
LCD Panel LVDS Interface Connector ....165
Serial Port Connection...............................67
LCD Voltage Setup ....................................52
Serial Ports ............................................. 153
Software Drivers ..................................... 177
M
Maintenance and Cleaning..........................5
Model Variation ..........................................20
Motherboard ..............................................35
Motherboard Replacement ........................70
Motherboard Specifications .......................28
Southbridge................................................37
Specifications .............................................26
System Maintenance .................................69
System Specifications................................26
T
Touch Panel Driver Configuration ........... 185
N
Northbridge ................................................36
U
Unpacking ..................................................45
O
Overview....................................................20
P
Packing List ...............................................46
Panel Mounting..........................................62
Parallel Port .............................................152
Parallel Port Connection............................67
USB Connection ........................................67
USB Port Connector ............................... 160
V
VGA Connector ....................................... 162
W
Wall Mounting ............................................59
Page 189
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement