advertisement
2M HD IP Fixed
Indoor Box Camera
Quick Manual
Ver. 1.0 / 2014.05
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the userwill be required to correct the interferenece at his own expense.
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that the plug is easily accessible.
1. Product & Accessories
The C-Lens and CS-Lens are not included in the product package.
C-Lens and CS-Lens is optional.
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may
cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may
cause fire.
5. When installing the camera, fasten it securely and firmly. A falling camera may cause
personal injury.
6. Do not place conductive objects (e.g. screw drivers, coins, metal things, etc.) or
containers filled with water on top of the camera. Doing so may cause personal injury
due to fire, electric shock, or falling objects.
2. Part Name
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued
use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way.
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a
location subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to
do so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any
time.
Important Safety Instructions
WARNING
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus.
13. Unplug this apparatus when a cart is used. Use caution
when moving the cart/apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Camera Holder (Mount) Holes
Lens Connector Port
Auto Iris Lens (Optional)
3. Installation
Disconnect the power before proceeding.
1 Mounting the Lens
- CS-Lens: Turn the optional CS-Lens
clockwise to insert it.
- C-Lens: Turn the C mount adaptor
clockwise to insert it and do
the same with the C-Lens.
CS-Lens Lens Connector
3 Connection Lens Connector
Connect the lens control cable to the lens connector.
Camera
C-Mount Adaptor Camera Holder Mount Camera Holder
Screw-2pcs
Micro SD Memory Card Slot
Power
RJ-45 Connector
GND
Audio In/Out Port
Factory Reset Switch
BNC Video Port
Power Port
Alarm Input/Output Port
C-Lens
2 Fix the Camera Holder
By tightening two camera holder screws provided, attach the camera holder on the camera.
4 Adjusting Zoom and Focus
By turning screws of the lens, adjust the
Zoom and Focus after setting the position and view angle of camera.
Manual CD Quick Manual
WARNNING
Factory Reset Switch
Resetting the camera IP address, subnet mask, gateway address etc. requires the use of the IP Installer software application.
Power Port
Be careful not to reverse the polarity when you connect the power cable. You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
4. Cabling
1 SD Card
2 RJ-45
3 BNC Cable
5 Alarm Input
6 Alarm Output
4 Power
1 SD Card
Insert or remove the SD card carefully.
2 RJ-45
Connect the crossover cable.
3 Monitor
Connects to video output device such as monitor using the BNC coaxial cable.
4 Power
Please check the correct rated power.
7 RS-485
5 Alarm Output
It connects to the alarm lights, siren or lamps, and it is activated according to the OSD menu setting.
6 Alarm Input
It connects to IR sensor, IrDA sensor or door switch. If the sensor is activated, it can activate to move camera to the specific angle and to connect the alarm device.
7 RS-485
Controls with device using RS-485 communication standards.
Mic.
Amplifier
Mic.
8 Audio In
9 Audio Out
Speaker
8 Audio In
Connect the ‘Audio In’ port of the camera to the microphone directly or ‘Line Out’ port of the amplifier connected with microphone.
If the microphone is connected directly, the
microphone with the embedded amplifier
such as condenser mic. needs to be used.
9 Audio Out
Connect the ‘Audio Out’ port of the camera to the ‘Line In’ port of the speaker.
If the speaker without the amplifier is
connected to Audio Out port, it doesn’t work
properly. Therefore, the speaker with the
amplifier or the separate amplifier is needed.
5. IP Installer
3
2
4
5
7
6
8
9
11
10
12
1. Run IP Installer
1 Run the manual CD and IP installer in
S/W folder.
2 Click on Network Adaptor selection Menu
(NIC) after run this program.
3 Select a network which a camera is connected then click on a ‘Search’ button. (Takes about 5 sec.)
4 Select a camera to set.
5 The information of the selected camera will be shown at Device Info.
6 Select the network type.
If the internet service is dynamic IP method which receive the IP address from DHCP server, please select DHCP.
If the IP address is received from a network administrator, please select STATIC and input other information on IP setting.
If the internet service is based on Static IP address and to set it directly to the camera, please contact to internet service center for detailed information.
7 Input IP setting information when the network type is set to STATIC.
Default TCP/IP information
- IP: 192.168.1.80
- Subnet Mask: 255.255.255.0
- Gateway: 192.168.1.1
- DNS : 168.126.63.1
8 Change the port as necessary when the network type is set to STATIC.
A ‘Port Forwarding’ has to be set for external access to the camera.
Refer to the manual of the network hub for
‘Port Forwarding’ settings.
An additional change of HTTPS, RTSP port can be done at Web Viewer >Admin page.
11 To reboot or reset (except network setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on Reboot
or Factory Reset button.
12 Able to delete an Active-X which is installed when accessing to Web Viewer.
Please try to re-install the Active-X after
deleting previous Active-X when there is a
problem with it. Changing the security option
of IE might be necessary depending on the
version of IE.
Note that all IE windows will be closed when
uninstalling Active-X.
9 Input ID and PW of the camera for authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Admin page>System>
Users” for ID and PW change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
Default ID / PW : admin / admin
10 Make sure to click on ‘Save’ button to save changed values.
An “Apply” message will be popped-up
when the settings are applied normally, or
an error message will be popped-up when
failed.
6. Web Viewer Screen
1 2 3
4
5
7
6
8
Disposal of Old Appliance
1. When this crossed-out wheel bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the
municipal waste stream in accordance to laws designated by the government or the
local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact
your city office, waste disposal service or the shop where you purchased the product.
Web viewer is optimized with Windows
XP or above version and explorer browser.
1 Live video display. This is the region for live video stream from the camera.
2 Resolution. The resolution of video that displays currently on the screen.
3 SD Card Search. Searching or Playing the Image which stored in the SD Card.
4 Setup popup button. Click it to open the Setup page to setup details of IP camera like Video, Network, Events,
System and etc.
5 Control tab button. Click it to extend the panel to setup 1) Video Format,
2) Backup, 3) Alarm Input and Relay
Output, 4) Audio setup, 5) Motion
Detection.
6 Full screen button. Click it to extend the live video to full screen. To return to normal mode, press ‘Esc’ or ‘Enter’ key.
7 Camera Setup popup button. Click it to open the Setup page to setup details of Lens, White Balance, Auto Exposure, image Backlight and etc.
8 Event alert icon. If Alarm in and Motion detection are detected, below icons will appear.
<Alarm Input> <Motion Detection>
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project