User Manual IP68 Waterproof Indicator

User Manual IP68 Waterproof Indicator
User Manual
IP68 Waterproof Indicator
QW
© Excell Precision Limited 2013. All rights reserved Worldwide.
The information contained herein is the property of Excell Precision Limited and is
supplied without liability for errors or omissions. No part may be reproduced or used
except as authorised by contract or other written permission. The copyright and the
foregoing restriction on reproduction and use extend to all media in which the
information may be embodied.
EXCELL PRECISION CO., LTD
Table of Contents
SPECIAL NOTICE ....................................................................................................................... 3
BEFORE USING THE SCALE ..................................................................................................... 4
INSTRUCTIONS FOR USE ......................................................................................................... 4
PREPARING TO USE THE SCALE ............................................................................................. 4
CHAPTER 1 INTRODUCTION .................................................................................................... 6
1-1 Product Features................................................................................................................ 6
1-2 Specifications ..................................................................................................................... 6
1-3 Product Appearance........................................................................................................... 7
1-4 Display Description............................................................................................................. 8
1-5 Power Supply ..................................................................................................................... 9
1-6 Keypad Function .............................................................................................................. 10
1-7 Self-Test Mode ................................................................................................................. 12
1-8 Error Messages ............................................................................................................... 13
1-9 Weight Units .................................................................................................................... 13
CHAPTER 2 CONFIGURATIONS.............................................................................................. 14
2-1 General Function Setting
....................................................................... 15
...................................................... 16
2-1-1 Auto Backlight Function Setting
2-1-2 Auto Power-off Timer Setting
.......................................................... 17
2-1-3 HI/LO/OK Settings
........................................................................... 18
......................................................... 19
2-1-4 Restore to the Default Settings
2-1-5 Noise Filter Settings
........................................................................ 20
2-1-6 Hold Function Settings
.................................................................... 21
................................................ 23
2-1-7 Auto Unit Weight Averaging Setting
2-1-8 Record Last Zero
2-1-9 Foot Switch Settings
................................................................................. 24
(Option) ............................................................. 25
.............................................................. 26
2-1-10 F Key Function Settings
2-1-11 Zero Setting
................................................................................. 27
2-2 External Weight Calibration
...................................................................... 28
............................................................. 29
2-3 RS232 Serial Interface Settings
2-3-1 Baud Rate Settings
02005155
.......................................................................... 30
1
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-2 Communication Protocol Settings
.................................................... 31
2-3-3 Output Format Settings
..................................................................... 32
2-3-4 Continuous Transmission Settings
................................................... 35
2-3-5 Selection of the Continuous Transmission Rate
2-3-6 Auto Transmission at Zero
................................... 36
.............................................................. 37
2-3-7 Reset Auto Transmission
.................................................................. 38
2-3-8 Output Condition Settings
................................................................ 39
2-3-9
RS232 6/7 Digits Setting
2-3-10 RTC Adjustment
........................................................... 40
....................................................................... 41
2-3-11 Y/M/D Print Layout Selection
......................................................... 42
2-3-12 RS485 ID Input (Option)
2-3-13 Line Feed Input
................................................................ 43
.............................................................................. 44
CHAPTER 3 WIRELESS CONNECTION INSTRUCTION ......................................................... 45
COMMAND MODE............................................................................................................... 51
OUTPUT DATA FORMAT ..................................................................................................... 54
APPENDIX I: ASCII CODE TABLE ............................................................................................ 56
APPENDIX II: 7 SEGMENT DISPLAY CHARACTERS .............................................................. 57
APPENDIX III: WIRING INSTRUCTIONS.................................................................................. 58
02005155
2
ZSME300000230
EXCELL PRECISION CO., LTD
SPECIAL NOTICE
While installing the load cell, power cord hookup or replacing a new rechargeable battery,
the indicator housing must be opened. It must be done by a technician assigned by your
electronic indicator provider to avoid affecting the waterproof ability of this indicator.
Before opening the housing, make sure the indicator is dry, if there is any liquid on it, please
wipe it with a clean cloth.
HOW TO INSTALL THE HOUSING:
After installing the load cell, power cord hookup or replacing a new rechargeable battery, the
housing must be screwed by the assigned order as shown below. Screw lightly first, then screw
them tight using a 12 kgf-cm torsion.
P.s. Please use a torsion-adjustable screw driver.
Screwing order:
3
5
02005155
1
6
4
2
3
ZSME300000230
EXCELL PRECISION CO., LTD
Thank you for purchasing EXCELL WEIGHING INDICATOR, to
help use the product properly, operate smoothly, and extend its
life cycle, please read this manual carefully.
BEFORE USING THE SCALE
In order to use this scale correctly, we suggest that you read this manual carefully.
INSTRUCTIONS FOR USE
1. The load placed on the weigh pan must NOT exceed the maximum weighing capacity
of the scale.
2. Protect the scale from high temperatures.
3. Avoid objects impacting with the scale. Do not drop loads onto the scale or subject the
weigh pan to any strong shock loads.
PREPARING TO USE THE SCALE
1. Locate the scale on a firm level surface free from vibrations for accurate weight readings.
2. Adjust the four levelling feet (if fitted) to set the scale pan level.
3. Avoid operating the scale in direct sunlight or drafts of any kind.
4. If possible avoid connecting the scale to ac power outlet sockets which are adjacent to
other appliances to minimise the possibility of interference affecting the performance of
the scale.
5. Remove any weight that might be on the weigh pan before the scale is switched on and
avoid leaving weight on the pan for long periods of time
6. All goods weighed should be placed in the centre of the weigh pan for accurate weighing.
The overall dimensions of the goods being weighed should not exceed the dimension of
the weigh pan.
7. Once the scale has been powered on, it will go through an LCD display test and it is ready
for use when the display shows zero.
8. The scale requires 15~20 minutes warm up before operation to ensure best accuracy
9. Please note when the
recharged.
symbol keeps flashing on the screen, the batteries need to be
10.Introduction of Storage Battery
02005155
4
ZSME300000230
EXCELL PRECISION CO., LTD
Due to the storage battery adopt the advanced free-maintaining technique, customers need not
to replenish electrolyte.
The scale should be recharged every 3 months to prevent failure of the internal rechargeable
battery.
1. The battery should be charged for 8~10 hours.
2. The temperature of battery should below 45℃.
Maintaining
1. Please do not discharge with over-current when using the battery. Please charge the battery
after discharging current.
2. Please take down the battery when the scale is not used for a long time or break the
connection of cathode.
3. Do not short the battery terminals to check whether there is current. Please check whether
the connection point is firm to guarantee good connection.
4. The battery should be replaced by specialized person. No reverse-battery or the product
will be damaged.
a) Anode of battery should be connected with Anode of product battery(usually red
cable)
b) Cathode of battery should be connected with Cathode of product battery (usually brown
cable or black cable)
c) See the picture following
Brown cable(or black cable)
connected with Anode of
battery
Red cable connected with
Cathode of battery
Safety warnings
1. The electrolyte of battery is caustic which causes metal, cotton, etc to corrode.
2. The hydrogen will be resolved when using or charging the battery and it will cause explosion
when approaches fire.
02005155
5
ZSME300000230
EXCELL PRECISION CO., LTD
CHAPTER 1 INTRODUCTION
1-1 Product Features
„
Extra-large and wide LCD display (175 x 70mm) 6 digits with 55mm height
„
COOL WHITE LED backlight
„
Type 304 stainless steel housing
„
Sealed to IP68, Waterproof, mist-proof and dustproof (Only use cables of
3mm~5mm diameter to ensure correct sealing of the cable glands)
„
Kilogram (kg) and pound (lb) weighing modes
„
Full range tare; Pre-tare; Auto zero tracking; Sampling counting;
Gross/Net indication
„
Hold function; Check mode Lo/Hi/OK; Auto average unit weight;
Animal scale function
„
Adjustable gravity value
„
Low power indication and auto power off
„
AC/DC power in and rechargeable battery.
„
Built-in RS-232
„
Options: wireless transmitter, pressure release valve, foot switch, and RS-485
1-2 Specifications
„
Analogue Input: Input Sensitivity 0.3μ V/d (Min.)
„
Input Signal Range: -1mV~+14mV
„
Input Zero Range: -1mV~+5mV
„
Load Cell Excitation: 5V DC
„
Load Cell Drive Capacity: Up to 8 x 350Ω load cells
„
Non-linearity: 0.01% of full scale
„
A/D Resolution: 500,000 counts (Maximum)
„
Operating temperature: 0℃ ~ 40℃
02005155
6
ZSME300000230
EXCELL PRECISION CO., LTD
1-3 Product Appearance
80 mm
232 mm
170 mm
[ Standard ]
[ Option ]
Load Cell
RS232
or RS485
Load Cell
RS232
Pressure relieve valve or RS485
Foot switch or RS485
Power
02005155
Power
7
ZSME300000230
EXCELL PRECISION CO., LTD
1-4 Display Description
1
HI
OK
LO
kg
lb
t
Pcs
Æ0Å
Net
:
:
:
:
:
:
:
:
:
:
2
3
4
5
6
7
Upper limit
Value between HI and LO
Lower limit
Unit “kilogram”
Unit “pound”
hk tael
Counting mode indication
Zero point indication
Net weight indication
Low Power indication
“” indications description:
1 : (STABLE) stable indication
2 : (GROSS) gross weight indication
3 : (
) unit weight insufficient indication
4 : ( PT ) pre-tare indication
5 : (Hold) weight hold indication
6 : “GN”、“dwt”、 “carat” 、”M+” unit indication
P cs
7 : “oz” or “viss” unit indication (set as needed), or no unit indication
02005155
8
ZSME300000230
EXCELL PRECISION CO., LTD
1-5 Power Supply
Power Supply Selection
➀ 6V / 4.5Ah rechargeable battery
➁ 110/230VAC ±15% (plugged-in)
Power Consumption
Approximately DC 31
Approximately DC 65
Approximately DC 80
Approximately DC 65
mA
mA
mA
mA
(Indicator + Load Cell)
(Indicator + Load Cell + Display backlight)
(Indicator + Load Cell + Wireless 100M)
(Indicator + Load Cell + Wireless 10M)
Charging Voltage
DC 10V/1A
Low Battery Warning
Please note when the (
) symbol keeps flashing on the display, the internal battery
should be recharged.
The scale will turn off automatically after a few hours when the low battery warning symbol
shows up. The scale must be fully charged, before operating again.
When the battery status indication is full, the power is about 6.1V; Each block is about 0.2V;
When the battery warning symbol shows up, the power is about 5.4V.
Safety Reminder:
z
Please make sure “+” , “- “ poles are placed in the correct direction
z
Please don’t’ place the battery in hot areas, or try to dissemble the battery, to avoid
electricity leakage.
z
Please don’t mix & use batteries of different models.
z
Please don’t keep the used-up battery in the battery case to avoid breakdown.
(dry cell models)
z
The battery inside the indicator was used for testing the fullness of the product.
Therefore, the life of the battery cannot be count from the day you purchase.
02005155
9
ZSME300000230
EXCELL PRECISION CO., LTD
1-6 Keypad Function
ON/OFF KEY
Press the ON/OFF key to switch the indicator on or off.
ZERO KEY
The ZERO key acts as the zero balance function. If the weighing value is within the
range of zero balance, it can be re-zeroed and tare cancelled.
Zero Range : OIML&NTEP is ±2% F.S., and Sri Lanka is ±3% F.S.
TARE/PT KEY: Tare/Pre-tare key
To TARE:
Place the container onto the scale, until the weight value is stable, press TARE/PT key for
zero return and the NET indication is shown on the display.
Place the object onto the container and the display shows the net weight value of the object.
Remove both object and container, and negative value of the container will show on
the display.
Press TARE/PT again to clear “tare value”. The scale returns to zero and NET indication
goes off.
Tare can be continuously done until tare value=full load capacity
Continuous Tare Æ Press TARE/PT key for continuous weight increase/decrease on
platter.
If there is Tare, the pre-tare cannot be done. If there is pre-tare first, and the tare weight
more than pre-tare weight, Tare can be done.
No Tare can be done under gross weight display mode.
To PRE-TARE:
Press TARE / PT key, use keypad to input pre-tare weight. When the cursor flashes on the
rightmost digit, press TARE / PT key again to complete.
Pre-tare mode, keypad function as followed:
ZERO => upward key(0~9 digit entry)
NET/GROSS => move cursor leftward
UNIT => downward key(0~9 digit entry)
TARE/PT => move cursor rightward
UNIT KEY
Press the UNIT key to switch weight units; the display icons will indicate the active units.
NET/GROSS KEY
In the Tare mode, the screen displays the “TARE” icon; press the NET/GROSS key to switch
between the “Net value” and the “Gross value”.
When the ”GROSS” arrow 6 shows up, the Gross Weight in the screen = Tare weight +
Net weight, meanwhile, keys except the NET/GROSS KEY, have no response.
02005155
10
ZSME300000230
EXCELL PRECISION CO., LTD
M+ | PRINT KEY
Totalization function. M+/Print function is available when RS232 is on keypad transmission
mode. (
output).
This key is a composite key, while totalization is shown and weight returns to net zero, press M+
key to erase memory. RS232 will output MC print format (
output).
If there is new weight added on platter(it is less than 20 divisions in Brazil version, no
accumulation ), a new item will be added to totalization. If this weight is not taken off,
nothing can be added to totalization.
Display will show the totalization numbers for one second, then show net weight for one
second, then the scale returns to the current weight, and prints out the last item for totalization.
To clear totalization data, press M+ key to let display shows up totalization numbers, then
press M+ again, to clear totalization data. RS232 will print out totalization numbers, total
weight, etc.
P.s. Weight must return to net zero if to perform clear function.
F KEY
Function key (In
, select F key as “MC” or “HR”
Foot Switch Mode:
This function is optional. Use FNC11 to select TARE/PT key as “ZERO” or “PRINT” key
If “PRINT” key is set (
= 10/11), all totalization data will be printed out, and
totalization will be cleared.
If it is Brazil version and foot switch is set as Print function, it has totalization function and
print function.
Simple Counting Mode
Use UNIT key to switch unit to Pcs, to go into simple counting mode.
1. Use NET/GROSS key, to select a sample number from “10 , 20, 50, 100, or 200”. Display
will show
、
、
、
、
in an sequential order by
pressing NET/GROSS key.
2. Select a sampling number, and put appropriate weight on platter, and press UNIT key. Display will
show “
”. The scale will go into counting mode after weight is stable, and
display will show the sample number.
Unit weight insufficient (
): Sample unit weight is less than 0.2d (d=division) or total
sample weight is less than 20d (d=division)
P cs
While sampling, if there is insufficient sample or unit weight insufficient indication “”, the
scale is still usable, but there may be slight inaccuracy.
After Power-off, the scale automatically memorizes the sampling number, and it is available
when “Pcs” unit is selected next time.
If the setting is “automatic average unit weight “, if the object on platter > the previous
sampling number more than 5 pcs, and also < less than 100% the previous sampling number,
the scale will execute unit weight calibration automatically.
02005155
11
ZSME300000230
EXCELL PRECISION CO., LTD
1-7 Self-Test Mode
When power is off, hold NET/GROSS , and press ON/OFF key,
to enter “Self-Test Mode”.
Wait till display shows
Press UNIT key
Press ZERO key
Press UNIT key
Press ZERO key
Press UNIT key
Press ZERO key
Press TARE/PT
k
INTERNAL VALUE MODE (must hook up full-bridge Load Cell to test)
c Press TARE / PT to enter, and the display shows internal value
d Please check the internal value is within normal range is 0 ~ 400000 (no load)
e Check whether the backlight is on
f Press ZERO key to back to the last screen , the display shows
KEYPAD TEST MODE
c Press TARE/ PT to enter, display shows
Keypad’s internal code: TARE/ PT key= 06 、 UNIT key= 05、 NET/GROSS key=04
F key = 02
d Press ZERO key to back to the last screen , the display shows
FIRMWARE VERSION DISPLAY MODE
c Press TARE/ PT to enter , display shows the firmware version
d Press TARE/ PT key again, the display shows maintenance number
seconds
e Press ZERO key to back to the last screen, display shows
,
for 2
BACK TO THE LAST SCREEN
Press TARE/ PT key to exit self-test mode, the scale will re-power on automatically.
02005155
12
ZSME300000230
EXCELL PRECISION CO., LTD
1-8 Error Messages
⇒ The EEPROM is not working correctly.
The EEPROM is not set yet, or the circuit on PCB is broken.
⇒ Zero is higher than the zero range when switching the indicator on.
⇒ Zero is lower than the zero range when switching the indicator on.
⇒ A/D value is unstable.
⇒ The weight of the object is over 9 divisions of the maximum capacity.
⇒ The weight of the object is under -1/6 maximum capacity.
⇒ ADIC value is over the maximum range.
⇒ The scale is not in level status.
(Only available with level detector equipped)
1-9 Weight Units
(kg)
(g)
(lb)
(lb/oz)
(oz)
(GN)
(dwt)
(ct)
(hk.tael)
viss
02005155
1g =
1g =
1g =
1g =
1g =
1g =
1g =
1g =
1g =
1kg =
0.001 kg
1g
0.002204623 lb
0.03527396 oz
0.03527396 oz
15.432358 GN
0.6430149 dwt
5 ct
0.02645546 Hk.catty
0.612245 viss
13
ZSME300000230
EXCELL PRECISION CO., LTD
CHAPTER 2 Configurations
Configuration Workflow
In the weighing mode, press the NET/GROSS
and ZERO keys at the same time to enter the
configuration mode.
.
The LCD shows
Overall workflow of the Advanced Function setting mode:
Press UNIT key
Press ZERO key
Press UNIT key
Press ZERO key
Press UNIT key
Press ZERO key
Press UNIT key
Press ON/ZERO key
⇒ General Function Setting Mode
⇒ External Weight Calibration
⇒ RS232 Bi-direction Function Setting
⇒ Exit the Advanced Function Setting Mode
Refer to the following sections for the detailed operation
procedures of each function setting.
02005155
14
ZSME300000230
EXCELL PRECISION CO., LTD
2-1 General Function Setting
Workflow of the General Function setting:
Press TARE/PT key
key in the parameter
“00 ~ 13”
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
Key in “00” and
press TARE/PT key to
return to the
Advanced
function setting
menu
NET/GROSS key ⇒ Move cursor leftward
⇒ Return to the Advanced Function Setting Mode Menu
⇒ Automatic Backlight Function Settings
⇒ Automatic Power-off Timer Settings
⇒ Hi/Lo/OK Settings
⇒ Restore the Default Settings
⇒ Noise Filter Settings
⇒ Hold Function Settings
⇒ Auto Unit Weight Averaging Setting
⇒ Reserved
⇒ Reserved
⇒ Record Last Zero
⇒ Foot switch on/off settings (Option)
⇒ F key function settings
⇒ Zero Setting
02005155
15
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-1 Auto Backlight Function Setting
Select
in the general function setting mode
the backlight function setting.
to change
Press TARE /PT key
LCD displays the last status
¾ Default setting = off
Use ZERO or UNIT key to
select function “on” or “off
On Æ backlight function is on
Off Æ backlight function is off
Press TARE/PT key to go
back to the advanced
function setting menu
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
Auto backlight function
When the weight is over 10d, the display backlight will be on. After the weight
is stable for 10 seconds or when the scale returns to zero, the display
backlight switches off.
02005155
16
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-2 Auto Power-off Timer Setting
Select
in the general function setting mode
the automatic power-off timer setting.
Press TARE/PT key
to change
LCD displays the last status
Default setting = 0 (No auto power-off)
Use ZERO or UNIT key to
key in parameter
Automatic power-off timer setting
Use ZERO or UNIT key to key in
parameter
Press TARE/PT key to
go back to the
Advanced function
setting menu
0 ⇒ No auto power-off
1 ⇒ When the scale is idle for 1
minute, the scale
automatically switches off
2 ⇒ When the scale is idle for 2
minutes, the scale
automatically switches off
9 ⇒ When the scale is idle for 9
minutes, the scale
automatically switches off
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
Auto power-off function
When the weight on weigh pan is less than 10d or keeps idle for the set time, the
scale will automatically switch off.
02005155
17
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-3 HI/LO/OK Settings
Select
HI/LO/OK function.
in the general function setting mode
to set the
When the high limit and low limit are both set as “0”, the Hi/Lo/OK function is disabled.
Press TARE/PT key
lb
.
Key in the desired high
limit value
.
LCD displays the last status
lb
Press TARE/PT key
.
lb
LCD displays the last status
Key in the desired low limit
value
.
lb
LCD displays the last status
Press TARE/PT key
Alarm setting
(a)(b)(c)
Key in the parameter
setting for alarm
The definition of a, b, c positions:
(a) ⇒ 1 = beep sound on
0 = beep sound off
(b) ⇒ 1 = beep sound on when stable
0 = beep sound on when unstable
Press TARE/PT key
(c) ⇒ 1 = beep sound on when the weight is
between high and low limits
0 = beep sound on when the weight is
not between high and low limits and
higher than 10d
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
18
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-4 Restore to the Default Settings
Select
in the general function setting mode
to the default settings.
to restore
Press TARE/PT key
⇒ Return (Cancel the
restoration)
Use ZERO or UNIT keys
to select “return”
or “format”
⇒ Restore the default
setting
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
The defaults are included the following:
1) External weight calibration
2) HI/LO/OK setting values
3) Noise filter setting (External)
4) Sampling settings for the counting function
02005155
19
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-5 Noise Filter Settings
Select
in the general function setting mode
noise filter settings.
When modifying
, the parameters of
to set the
remain un-altered.
Returning to zero point setting
LCD displays the last status
Press TARE/PT key
Returning to the zero point setting
Use ZERO or UNIT key to key in the
parameters or zero point
¾ Default setting = 0
0 ⇒ No skip
5 ⇒ skip 5d
1 ⇒ skip 1d
6 ⇒ skip 6d
2 ⇒ skip 2d
7 ⇒ skip 7d
3 ⇒ skip 3d
8 ⇒ skip 8d
4 ⇒ skip 4d
9 ⇒ skip 9d
„ When the weight on the scale is over 1/3
full capacity, the function is on.
Use ZERO or UNIT key
to key in
the parameters
Press TARE/PT key
Digital switch & Stabilization range setting
LCD displays the last parameter setting
Use ZERO or UNIT key to
key in the parameters
Digital switch & Stabilization range setting
Use ZERO or UNIT keys to key in the
parameters.
¾ Default setting = 0
Parameter 0 ~ 9, the larger the number the
more stable the weight.
Press TARE/PT key
Filter parameter setting
LCD displays the last parameter setting.
Use ZERO or UNIT
key to key in
the parameters
Filter parameter setting
Use ZERO or UNIT keys to key in the
parameters.
Press TARE/PT key
02005155
¾ Default setting = 5
Parameter 0 ~ 9.
The larger the number is, the faster the
filter responds. Fast response can lead to
weighing instability.
Parameter 9 Æ the AD value is not filtered.
Input AD value = Output AD value
20
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-6 Hold Function Settings
Press TARE/PT key
Hold function setting
LCD displays the last parameter setting
Hold function setting
Use ZERO or UNIT keys to key in the
parameters
¾ Default setting = 0
0 ⇒ Hold function disabled
1 ⇒ “Peak hold” mode
2 ⇒ “Stable hold 1” mode
3 ⇒ “Stable hold 2” mode
4 ⇒ “Animal scale hold” mode
Use ZERO or UNIT key to
key in the parameters
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
= Hold function disabled
= “Peak hold” mode
The scale keeps displaying the maximum weight when the weight is continually
changing. Press any key to exit this mode.
= “Stable hold 1” mode
When the weight is stable, the LCD shows the current weight value. Press any
key to exit this mode.
= “Stable hold 2” mode
When the weight is stable, the LCD shows the current weight value. When the
weight returns to zero (<10d), the hold mode is cancelled automatically.
= “Animal scale hold” mode
When the scale returns back to zero, the display shows “ - - - - - - ”. After the animal or object is
on the platter and the scale becomes stable, the display shows the weight value and hold.
Then when the animal or object is off the platter, the display shows “ - - - - - - ” (or the weight is
less than 10e) and the hold function is off. If the scale is hardly stable when the animal is on
the platter, the scale shows the average weight in 10 seconds and holds the status.
02005155
21
ZSME300000230
EXCELL PRECISION CO., LTD
Hold Function Setting (Animal scale)
Hold function setting
LCD displays the last parameter setting
Press TARE/PT key
Hold function setting
Use ZERO or UNIT keys to key in 4 and
press TARE/PT key to enter the hold function
setting mode.
Use ZERO or UNIT key to
key in the parameters
Press TARE/PT key
%
Use ZERO or UNIT key to
key in the parameters
Error range setting
Use ZERO or UNIT keys to key in the
parameters ( Among 1%~100%)
Default setting = 10%
%
Press TARE/PT key
Use ZERO or UNIT key to
key in the parameters
Counts averaging setting
Use ZERO or UNIT keys to key in the
parameters (1,2,4,8,16,32,64)
Default setting = 8
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
22
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-7 Auto Unit Weight Averaging Setting
Press TARE/PT key
Auto unit weight averaging setting
LCD displays the last parameter setting
Use ZERO or UNIT key to
key in the parameters
Auto unit weight averaging setting
Use ZERO or UNIT keys to key in the
parameters
¾ Default setting = 0
0 ⇒ Auto unit weight averaging
1 ⇒ Non auto unit weight averaging
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
23
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-8 Record Last Zero
Press TARE/PT key
LCD displays the last parameter setting
Use ZERO or UNIT key to
enter the parameter.
Record Last Zero
Use ZERO or UNIT Key to select the setting.
Default setting =
⇒ Record the last zero setting
Press TARE/PT key
⇒ No record
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
24
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-9 Foot Switch Settings
(Option)
Foot switch on “ZERO” function
Press TARE/PT key
Display shows parameter from
the previous setup
Use ZERO or UNIT key
to select parameter
Foot switch on “TARE” function
Use ZERO or UNIT key
to select parameter
Foot switch on “PRINT” function
RS232 print out data sent from
pressing M+ key
Press TARE/PT key
If it is Brazil version and
=
_
, the format is
format and it has totalization function.
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
25
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-10 F Key Function Settings
F key function represents
“MC” function
Display shows parameter from
the previous setup
Press TARE/PT key
Use ZERO or UNIT key
To select parameter。
F key function represents
“HR” function
F key function represents
tare or pre-tare value
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
26
ZSME300000230
EXCELL PRECISION CO., LTD
2-1-11 Zero Setting
Press TARE/PT key
Unrestricted zero setting off
Display shows parameter from
the previous setup. Here is:
Use ZERO or UNIT key
To select parameter。
Unrestricted zero setting on
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
27
ZSME300000230
EXCELL PRECISION CO., LTD
2-2 External Weight Calibration
Press TARE/PT key, the display
shows the calibration value. The
right digit keeps flashing.
The calibration value could
be changed
Press NET/GROSS key
to move the flashing
digit to the left.
kg
.
kg
.
Press NET/GROSS key
to skip
When the right digit is flashing,
press TARE/PT key while ther
e is no load on platter
kg
Reading Zero
About 2 seconds later
kg
.
Press NET/GROSS key to exit
Put the calibrated weight on
platter and press TARE/PT key;
After 3 beep sounds, calibration
completes;
Remove weight
About 2 seconds later
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
The conditions for external weight calibration:
The calibration weight value placed on the platter must be over 100e, and the standard
deviation of the weight must be within 10%.
02005155
28
ZSME300000230
EXCELL PRECISION CO., LTD
2-3 RS232 Serial Interface Settings
For command format, please refer to page 51
Output format, please refer to page 54
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
Key in the parameter 00 ~ 08
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
Key in the parameter “00”,
then press TARE/PT key
to exit
⇒ Exit the RS232 Serial Interface Setting Mode
⇒ Baud Rate Settings
⇒ Communication Protocol Settings
⇒ Output Format Settings
⇒ Transmission method setup
⇒ The Selection of Continuous Transmission Rate
⇒ Auto Transmission at Zero
⇒ Reset of Auto Transmission
⇒ Output Condition Settings
⇒ RS232 6/7 digits setting
⇒ RTC adjustment
⇒ Y/M/D Print Format Selection
⇒ RS485 ID Input (Option)
⇒ Line Feed Input
02005155
29
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-1 Baud Rate Settings
Select
set the Baud Rate.
in the RS232 serial interface setting mode
to
Press TARE/PT key
Baud rate setting
LCD displays the last value
¾ Default value: 9600 (bits/sec)
Use ZERO or UNIT key to
select the desired
Baud rate
Baud rate setting
Use ZERO or UNIT keys to select the
desired Baud rate 600、1200、2400、
4800、9600、19200 (bits/sec)
Press TARE/PT key
Key in the parameter “00”
Press the TARE/PT key
to exit
ZERO key
UNIT key
⇒ Upward key (0~9 digit entry)
⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
30
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-2 Communication Protocol Settings
Select
in the RS232 serial interface setting mode
set the Communication Protocol.
to
Press TARE/PT key
Communication protocol setting
LCD shows the last setting value.
¾
Default setting:
Use ZERO or UNIT key to
select the protocol setting
Communication protocol setting
Use ZERO or UNIT keys to select the
protocol setting: n 8 1, E 7 1, O 7 1
Press TARE/PT key
Key in the parameter “00”
Press TARE/PT key to exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
31
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-3 Output Format Settings
Select
in the RS232 serial interface setting mode
set the Output Format.
to
RS232 output format setting
LCD shows the last setting.
¾ Default setting:
Press TARE/PT key
RS232 output format setting
Use ZERO or UNIT keys to select the
output format:
Use ZERO or UNIT key to
select the output format
= Same data as the scale
= Gross weight
= Net weight
= Same data as the scale in
simple format
= Same gross data as the scale
in simple format
= Same net data as the scale
in simple format
= Hi/Lo/OK status + Same data
as the scale in simple format
= Hi/Lo/OK status + Simple
gross weight
= Hi/Lo/OK status + Simple net
weight
= Tare value
Press TARE/PT key
Key in
the parameter “00”
Press the TARE/PT key
to exit
= M+ Transmission 1 note1
= M+ Transmission 2 note2
= Brazil printing format
ZERO key ⇒ Upward key (0~9 digit entry)
note 3
Format 12. are only for Brazil
Format 10.11 are not available on
counting mode
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
32
ZSME300000230
EXCELL PRECISION CO., LTD
Note1:
Ticket No.
Date year/month/day & day/month/year (choose 1 out of 2 date formats)
Time
G
T
N
Total Net (This line will only print when data is erased, showing net weight total of every count)
Note2:
Ticket No.
Date year/month/day & day/month/year (choose 1 out of 2 date formats)
Time
G
T
N
Total weight (This line will only print when data is erased, showing gross weight total of every
count)
Note3:
If it is not Brazil version, it can only print under continuous transmition.
If it is Brazil version, under decimal units mode,
=
and
can print out. It is not available on counting mode.
For example:
70.15Kg print as: =51.07000=51.07000=51.07000=51.07000=51.07000
negative 70.15Kg print as: =51.0700-=51.0700-=51.0700-=51.0700-=51.0700-
= _
, it
Note4:
If it is not Brazil version, it can print under key transmition, auto transmition and order mode.
=
If it is Brazil version, when the scale is stable and under under decimal units mode,
and
, it can print out.. It is not available on counting mode.
= _
Transformat as followed:
F
R
“
I
R
W
? <LF>
G G
G ,
G
G
T
T
T ,
T
T
N
N
N ,
N
N
A
A
A ,
A
A
C
C
C C
C
C
D
D
/ M
M
/
H
H
: m
m
:
n
n
n ,
n
n
P
1
, 1 <LF>
T
3
0
G
T
N
A
<LF>
Y
S
n
<LF>
<LF>
<LF>
<LF>
Y
S
t
G = gross weight
T,t = tare
N,n = net weight
A,a = accumulating weight
C,c =accumulating times
D = date (DD/MM/YY)
DD: day
H = time(HH:mm:SS)
HH: hour
02005155
0
<LF>
<LF>
t
0
t
MM: month
mm: minute
33
“
<LF>
,
t
t
t a a a , a a a c c c c c c <LF>
YY: year
SS: second
ZSME300000230
EXCELL PRECISION CO., LTD
For example:
tare 0.2kg, net weight 1key, press M+:
FR”IRWT3000”
?
1,200
0,200
1,000
1,000
1
30/05/00
00:54:12
001,000000,200001,000000001
P1,1
Note5
If it is not Brazil version, it only can print under continuous transmition.
If it is Brazil version, under decimal units mode,
can print out. It is not available on counting mode.
=
and
= _
, it
Transformat as followed:
S,GGG .GGG ,TTT .TTT,NNN.NNN
S = 0:stable 1: unstable
G = gross weight
T = tare + pre-tare
N = net weight
For example:
tare 1 kg, net weight 0.2key, gross weight 1.2 kg , stable, then show as followed:
0,001.200,001.000,000.200
Take off the weight then show as followed:
0,000.000,001.000,-01.000
02005155
34
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-4 Continuous Transmission Settings
Select
in the RS232 serial interface setting mode
set the Continuous Transmission status.
to
Press TARE/PT key
Transmission setting
LCD shows the last setting
¾ Default setting:
Use ZERO or UNIT keys to
select the transmission
type
Transmission setting
Use ZERO or UNIT keys to select the
transmission type:
Press TARE/PT key
Key in the parameter “00”
_
= Command mode
= Continuous transmission
= Constantly auto
transmission
= Shut down RS232
= M+ Mode
Press the TARE/PT key to
exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
35
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-5 Selection of the Continuous Transmission Rate
Select
in the RS232 serial interface setting mode
set the Continuous Transmission Rate.
to
Press TARE/PT key
Continuous transmission rate setting
The LCD shows the last setting.
¾ Default setting:
Use the ZERO or UNIT keys
to select the continuous
transmission rate.
Use ZERO or UNIT keys to select the
continuous transmission rate:
= 1 time/sec
= 2 times/sec
= 4 times/sec
= 8 times/sec
= 16 times/sec
= More than16 times/sec
Press TARE/PT key
Key in the parameter “00”
Note: Actual output times vary by
hardware implements
Press the TARE/PT key
to exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
36
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-6 Auto Transmission at Zero
Select
in the RS232 serial interface setting mode
set the Auto Transmission at Zero.
to
Press TARE/PT key
Auto transmission at zero
LCD shows the last setting
¾ Default setting:
Use ZERO or UNIT keys to
key in the desired
parameters
Auto transmission at zero
Use ZERO or UNIT keys to key in the desired
parameters:
= 00 division of weight value
Press TARE/PT key
= 01 division of weight value
= 99 divisions of weight value
Key in the parameter “00”
Press the TARE/PT key
to exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
When the value of “Auto transmission at zero” set as
, the “Auto transmission
at zero” function is not available. Because when the scale is at zero and keeping stable, the
data are keeping transmitted, and that would be the same as “Continuous Transmission”.
02005155
37
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-7 Reset Auto Transmission
Select
in the RS232 serial interface setting mode
Reset Auto Transmission.
Press TARE/PT key
to
Resetting auto transmission
The LCD shows the last setting
¾ Default setting:
Use ZERO or UNIT keys to
key in the desired
parameters
Resetting auto transmission
Use ZERO or UNIT keys to key in the
desired parameters:
= 00 division of weight value
= 01 division of weight value
Press TARE/PT key
= 99 divisions of weight value
Key in the parameter “00”
Press TARE/PT key to exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
When the value of “Auto transmission at zero” set as
, the “Auto transmission
at zero” function is not available. Because when the scale is at zero and keeping stable, the
data are keeping transmitted, and that would be the same as “Continuous Transmission”.
02005155
38
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-8 Output Condition Settings
Select
in the RS232 serial interface setting mode
Reset of Auto Transmission.
to
Press TARE/PT key
Output condition settings
The LCD shows the last setting.
¾
Use ZERO or UNIT keys
to select the desired
setting
Default setting:
Output condition settings
Use ZERO or UNIT keys to select the
desired setting:
= All output
Press TARE/PT key
= Stable output
(No output when OL or unstable)
= Stable output
(OL included)
Key in the parameter “00”
Press the TARE/PT key to
exit RS232 2-way serial
interface settings
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
39
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-9
RS232 6/7 Digits Setting
Select
in the RS232 serial interface setting mode
Reset of Auto Transmission.
to
Press TARE/PT key
Output Condition Restriction Settings
Display shows the previous setup
Factory Default is
(6 places)
Use ZERO or UNIT keys
to select the desired
setting
Output Condition Restriction Settings
Use ZERO or UNIT key, to select
desired setting.
Press TARE/PT key
Output condition:
= 6 digits
= 7 digits
Press TARE/PT key
Press the TARE/PT
key to exit
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
40
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-10 RTC Adjustment
Select
in the RS232 serial interface setting mode
reset of Auto Transmission.
to
Enter the date in YY/MM/DD
Use upward and downward key to
select, and use TARE/PT key to confirm
Press TARE/PT key
Move cursor to the right end and
press TARE/PT key
Press TARE/PT key
Enter time in HH/MM/SS
Use upward and downward key to
select, and use TARE/PT key to
confirm, and move rightward.
Press TARE/PT key
Move cursor to the right end and
press TARE/PT key to confirm.
RTC adjustment is complete
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
41
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-11 Y/M/D Print Layout Selection
Select
in the RS232 serial interface setting mode
reset of Auto Transmission.
to
Display shows the previous setup
Use upward and downward key to select,
and use TARE/PT key to confirm
Print TARE/PT key
If y_m_d, printed as Year/Month/Day
If d_m_y, printed as Day/Month/Year
Use ZERO or UNIT keys
to select the desired
setting
Print TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
42
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-12 RS485 ID Input
Select
Auto Transmission.
(Option)
in the RS232 serial interface setting mode
to reset of
Press TARE/PT key
Display shows the previous setup
Use upward and downward key to
select, and use TARE/PT key to confirm
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
43
ZSME300000230
EXCELL PRECISION CO., LTD
2-3-13 Line Feed Input
Line feed would be available only when
was set as 10 or 11.
Factory default: 2
Display shows the previous setup
Use upward and downward key to
select, and use TARE/PT key to
confirm
Press TARE/PT key
Press TARE/PT key
ZERO key ⇒ Upward key (0~9 digit entry)
UNIT key ⇒ Downward key (0~9 digit entry)
TARE/PT key ⇒ Move cursor rightward
NET/GROSS key ⇒ Move cursor leftward
02005155
44
ZSME300000230
EXCELL PRECISION CO., LTD
CHAPTER 3 Wireless Connection Instruction
Step 1: Connect to your device
1. Enable Wireless on your computer. Right-click on the
taskbar, highlight “New Connection” and left click.
icon of the bottom-right corner on
Due to the different bluetooth supplier software could be installed, the setting dialogs shown
below are just for reference.
2. Check “My device is set up and ready to be found” in the dialogue box.
02005155
45
ZSME300000230
EXCELL PRECISION CO., LTD
3. If the device is ready, the device names Device-C1 or C2 will be found. Double-click on
Device-C1 or Device-C2.
4. Circle “Let me choose my own passkey”, input the passkey “111111” and click
“Next > ” button
02005155
46
ZSME300000230
EXCELL PRECISION CO., LTD
5. Device is added so far. Please disconnect COM port and click “Finish.”
Step 2: Connection test
To test the connection, use HyperTerminal recommended in Windows XP
1. go “START” → “All programs” → “Accessories“→ “Communications“→
“HyperTerminal”
02005155
47
ZSME300000230
EXCELL PRECISION CO., LTD
2. Key in a name and select icon, then press “OK.”
3. After select the COM port referred by step 1 point 5 and click “OK.”
02005155
48
ZSME300000230
EXCELL PRECISION CO., LTD
4. Click “File” → “Properties”
5. Select “settings” from the menu, and click “ASCII setup” on the bottom of the box.
02005155
49
ZSME300000230
EXCELL PRECISION CO., LTD
6. Check “Send line ends with line feeds” and “Echo typed characters locally” and click
“OK”.
7. Key in commands such RW, MZ, and RG in the main screen to test...
02005155
50
ZSME300000230
EXCELL PRECISION CO., LTD
Command Mode
On RS485 command mode, the format is as following,
1. If RS485’s ID setting is 0(RS1 12), and the command is the same as regular RS232.
2.
A. If RS485’s ID setting is not 0(assume 99),”@ID” has to be added in front of every
command. If you wish to command a zero-return, the complete command is @99MZY,
then press “ENTER” key
B. If there is an error on entered command, letter “E” will show up + “Unidentified
Command”
e.g. @99MZZ
The response message is => 99E1MZZ
3. RS485 responses only to machines of identified ID code
Command Format A
Host
Slave
Command
Command
MZ Zero
SO Command mode
MT Tare
UA Switch to the first unit
MG Gross weight
UB Switch to the second unit
MN Net weight
UC Switch to the third unit
CT Clear TARE value
UD Switch to the forth unit
SC Continuous transmission
UE Switch to the fifth unit
SA Auto transmission
UF Switch to the sixth unit
%
Stop continuous transmission and enter the command mode
Note: UA ~ UF settings are depended on the model of the scale
Command Format B
Host
Slave
RW
RG
Command
Data
Read Gross (simple)
Read Net (simple)
Read comparison situation +
RN Read Net weight
RJ current display of weight
(simple)
Read comparison situation +
RT Read TARE
RK
Gross (simple)
Read current display of
Read comparison situation +
RB
RL
weight (simple)
Net (simple)
Note: a. add % before the command to read continuously
b. add # before the command to transmit a stable value
02005155
Read current weight
Read Gross weight
RH
RI
51
ZSME300000230
EXCELL PRECISION CO., LTD
RJ,RK,RL Command Description
If RL command entered, and
if weight is higher than HI (FNC 03 setting), and if the current weight is 10 kg, the following will
be displayed: “100+ 10.000”
If weight is higher than HI (FNC 03 setting), and if the current weight is 0.5 kg, the following will
be displayed: “001+ 0.500”
If weight is between HI and LOW, and if the current weight is 1 kg, the following will be
displayed: 010+ 1.000
Read weight comparison setting value RS{{……
{{: Groups(00 ~ 09) ……: Setting Items
HI
Show “HI” presetting value
LO
Show “LO” presetting value
Note : {{(Group) is various depended on different models
00 ⇒ The first group
01 ⇒ The second group
02 ⇒ The third group
EX:
ANS:
RS02LO<CR><LF>
RS02LOXXXXXX<CR><LF>
Show “LO” presetting value
Command Format C
Host
Slave
Command+ Data
Command+ Data
Write weight comparison setting value WS{{……XXXXXX
{{: Groups(00 ~ 09) ……: Setting Items XXXXXX: Setting Value
HI
Write “HI” setting value
LO
Write “LO” setting value
Note : {{ (Group) is various depended on different models
00 ⇒ The first group
01 ⇒ The second group
02 ⇒ The third group
EX:
ANS:
02005155
WS00HI001000<CR><LF>
WS00HI001000<CR><LF>
52
Write “HI” setting value
ZSME300000230
EXCELL PRECISION CO., LTD
Command Format D
Host
Slave
Data
Position of
decimal point
Value (e.g. Price)
1
2
3
4
5
6
CR
LF
1
When the Slave receives this data format, it will transfer the data and display it on
its LCD.
․
Note: The function is effective when the weight value is over 0.
The above 4 (ABCD) command formats are RS232 bi-directional. There are
the following error messages received by Slave terminal (scale).
Error messages:
E1: Wrong command
E2: Command format error (Wrong parameters)
E3: Command not recognised
02005155
53
ZSME300000230
EXCELL PRECISION CO., LTD
Output data format
1. 7 places ( first decimal place not included)
Weight format
Gross
Net
Tare
Plus OL
Minus OL
Unstable
S
S
S
O
O
U
T
T
T
L
L
S
,
,
,
,
,
,
G
N
T
G
G
G
S
T
R
S
S
S
,
,
,
,
,
,
+ 0 1 2
+ 1 . 2
+ 0 1 2
+ SP SP SP
- SP SP SP
+ 0 1 2
2
2
2
SP
SP
3
3
.
SP
SP
.
4
3
SP
SP
4
5
4
SP
SP
3
3
.
SP
SP
3
4
.
3
SP
SP
4
5
4
4
SP
SP
.
6
5
5
SP
SP
5
7
6
6
SP
SP
6
SP
t
SP
SP
SP
SP
SP
l
SP
SP
SP
SP
o
.
k
SP
SP
l
z
g
g
CR LF
SP
SP
b
Simple format
G/N
G/N
G/N
Plus OL
Minus OL
+ 1 .
+ 0 1
+ 0 1
+ SP SP
- SP SP
5
.
5
SP
SP
6
6
6 CR LF
SP
SP
Comparison status + Simple format
Byte0 Byte1 Byte2 +/-
1
.
2
3
.
4
5
6
CR
LF
Byte0 : HI 30H/31H
Byte1 : OK 30H/31H
Byte2 : LO 30H/31H
2. 6 places ( first decimal place not included)
Weight format
Gross
Net
Tare
Plus OL
Minus OL
Unstable
S
S
S
O
O
U
T
T
T
L
L
S
,
,
,
,
,
,
G
N
T
G
G
G
S
T
R
S
S
S
,
,
,
,
,
,
+ 1 2 3
+ . 2 3
+ 1 2 .
+ SP SP SP
- SP SP SP
+ 1 2 3
4
.
3
SP
SP
4
5
4
4
SP
SP
.
6
5
5
SP
SP
5
7
6
6
SP
SP
6
SP
t
SP
SP
SP
SP
SP
l
SP
SP
SP
SP
o
.
k
SP
SP
l
z
g
g
CR LF
SP
SP
b
Simple format
G/N
G/N
G/N
Plus OL
Minus OL
02005155
+
.
2 3
.
4 5 6
+ 1 2 3 4 5
.
6
+ 1 2
.
3 4 5 6 CR LF
+ SP SP SP SP SP SP SP
- SP SP SP SP SP SP SP
54
ZSME300000230
EXCELL PRECISION CO., LTD
Comparison status + simple format
Byte0 Byte1 Byte2
+/-
.
2
3
.
4
5
6
CR
LF
Byte0 : HI 30H/31H
Byte1 : OK 30H/31H
Byte2 : LO 30H/31H
Serial Data Transfer/Receive Format
LSB
MSB
n,8,1
S
8-bit data
STOP
e,7,1
S
7-bit data
P STOP
o,7,1
S
7-bit data
P STOP
1
0
1
0
1
0
Note:
S
: Start bit
STOP: Stop bit
P
: Parity bit
02005155
55
ZSME300000230
EXCELL PRECISION CO., LTD
APPENDIX I: ASCII CODE TABLE
Symbol
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
02005155
ASC II
Code
41H
42H
43H
44H
45H
46H
47H
48H
49H
4AH
4BH
4CH
4DH
4EH
4FH
50H
51H
52H
53H
54H
55H
56H
57H
58H
59H
5AH
ASC II
Code
61H
62H
63H
64H
65H
66H
67H
68H
69H
6AH
6BH
6CH
6DH
6EH
6FH
70H
71H
72H
73H
74H
75H
76H
77H
78H
79H
7AH
Symbol
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
56
Symbol
0
1
2
3
4
5
6
7
8
9
↵
ASC II
Code
30H
31H
32H
33H
34H
35H
36H
37H
38H
39H
0DH
ZSME300000230
EXCELL PRECISION CO., LTD
APPENDIX II: 7 SEGMENT DISPLAY CHARACTERS
Digit
02005155
7 segment letter
Alphabet
7 segment letter
Alphabet
0
A
N
1
B
O
2
C
P
3
D
Q
4
E
R
5
F
S
6
G
T
7
H
U
8
I
V
9
J
W
K
X
L
Y
M
Z
57
7 segment letter
ZSME300000230
EXCELL PRECISION CO., LTD
APPENDIX III: Wiring Instructions
Load cell wiring method
(1) As shown below, when a load cell is connected with a 4PIN cable, SEN+
and SEN- can be unconnected. J11 and J12 on PCB must be tin-soldered
in short circuit.
(2) If Load Cell is 6PIN, please wire as the following diagram:
02005155
58
ZSME300000230
EXCELL PRECISION CO., LTD
RS232 wiring instruction
To connect RS232, please open the housing, RS232’s PIN connectors locate
on the bottom-right corner of the main board. The most common connection
method is using 9PIN and 25PIN, as shown below:
PC
Printer
PIN
Function
2
Transmit Data
Female 9 PINS
Function
SG
3
Receive Data
RxD
5
Signal Ground
TxD
PIN
Function
QW
Male 25 PINS
Function
2
Receive Data
SG
3
Transmit Data
RxD
7
Signal Ground
TxD
QW
RS485 wiring instruction
PC
Printer
PIN
Function
2
Transmit Data
Female 9 PINS
Function
SG
3
Receive Data
DA
5
Signal Ground
DB
PIN
Function
QW
Male 25 PINS
Function
2
Receive Data
SG
3
Transmit Data
DA
7
Signal Ground
DB
QW
To use other connection methods, please identify the signal and following the
above principles. After it is finished, please install the housing by the instruction in
the SPECIAL NOTICE.
02005155
59
ZSME300000230
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement