Portwell WADE-8022 User manual

WADE-8022

Mini-ITX Board

User's Manual

Version 1.0

Copyright © Portwell, Inc., 2014. All rights reserved.

All other brand names are registered trademarks of their respective owners.

Preface

Table of Contents

How to Use This Manual

Chapter 1 System Overview....................................................................................................... 1-1

1.1 Introduction ....................................................................................................... 1-1

1.2 Check List........................................................................................................... 1-2

1.3 Product Specification........................................................................................ 1-2

1.3.1 Mechanical Drawing................................................................................ 1-4

1.4 System Architecture.......................................................................................... 1-6

Chapter 2 Hardware Configuration ........................................................................................... 2-1

2.1 Jumper Setting ................................................................................................... 2-1

2.2 Connector Allocation...................................................................................... 2-10

Chapter 3 System Installation.................................................................................................... 3-1

3.1 Intel ® Haswell Processor .................................................................................. 3-1

3.2 Main Memory .................................................................................................... 3-1

3.3 Installing the Mini-ITX Board Computer ...................................................... 3-2

3.3.1 Chipset Component Driver .................................................................... 3-2

3.3.2 Intel ® Integrated Graphics Controller................................................... 3-3

3.3.3 Gigabit Ethernet Controller .................................................................... 3-3

3.3.4 Audio Controller...................................................................................... 3-3

3.4 Clear CMOS Operation .................................................................................... 3-3

3.5 EC WDT.............................................................................................................. 3-4

3.6 EC GPIO ............................................................................................................. 3-6

Chapter 4 BIOS Setup Information............................................................................................ 4-1

4.1 Entering Setup - Launch System Setup.......................................................... 4-1

4.2 Main .................................................................................................................... 4-2

4.3 Configutation..................................................................................................... 4-3

4.4 Boot ................................................................................................................... 4-23

4.5 Security ............................................................................................................. 4-25

4.6 Save & Exit ....................................................................................................... 4-26

Chapter 5 Troubleshooting ........................................................................................................ 5-1

5.1 Hardware Quick Installation........................................................................... 5-1

5.2 BIOS Setting ....................................................................................................... 5-3

5.3 FAQ ..................................................................................................................... 5-4

Preface

How to Use This Manual

The manual describes how to configure your WADE-8022 system board to meet various operating requirements. It is divided into five chapters, with each chapter addressing a basic concept and operation of Mini-ITX Board.

Chapter 1: System Overview. Presents what you have in the box and give you an overview of the product specifications and basic system architecture for this series model of Mini-ITX Board.

Chapter 2: Hardware Configuration.

Show the definitions and locations of Jumpers and Connectors that you can easily configure your system.

Chapter 3: System Installation.

Describes how to properly mount the CPU, main memory and Compact Flash to get a safe installation and provides a programming guide of Watch Dog Timer function.

Chapter 4: BIOS Setup Information.

Specifies the meaning of each setup parameters, how to get advanced BIOS performance and update new BIOS. In addition, POST checkpoint list will give users some guidelines of trouble-shooting.

Chapter 5: Troubleshooting.

Provide various of useful tips to quickly get

WADE-8022 running with success. As basic hardware installation has been addressed in Chapter 3, this chapter will basically focus on system integration issues, in terms of backplane setup, BIOS setting, and OS diagnostics.

The content of this manual is subject to change without prior notice. These changes will be incorporated in new editions of the document. The vendor may make supplement or change in the products described in this document at any time.

System Overview

Chapter 1

System Overview

1.1 Introduction

Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market and a member of the Intel ® Embedded and Communications Alliance (Intel ® ECA), announced today the Portwell WADE-8022 adopting the Mini-ITX form factor. The

WADE-8022 of the Intel ® platform will provide high performance and flexibility for functional expansion, such as Gaming, Kiosk, DS, Medical, Defense, Industrial automation and control applications.

Haswell mobile processors is the next major architecture from Intel ® . The

WADE-8022 supports the latest Intel ® Haswell mobile processors in BGA1364 package which has memory and PCI Express controller integrated to support

2-channel DDR3L memory and PCI Express 3.0 lanes providing great graphics performance. Intel ® Haswell mobile processor is one of the most powerful and energy efficient CPU in the world. Portwell have taken advantage of such technology to furnish a series of products that can meet multiple industrial requirements such as cost-effective of CPU performance or industrial systems.

WADE-8022 is based on the Intel ® Haswell mobile processor with Intel ® QM87 chipset.

The Intel ® QM87 Express Chipset, when combined with a processor from the Intel ®

Dual Core/Quad Core mobile processor family, delivers smart security, cost saving manageability, and Intel ® ligent performance for business platforms. WADE-8022 is the first Portwell off-the-shelf product for by Intel ® QM87 Express Chipset, it can be an embedded solution and a good platform for customer to integrate it to the embedded system.

WADE-8022 showcased one of Portwell upcoming motherboard for the Intel ® ’s

Haswell mobile processors. The WADE-8022 is based on the forthcoming Intel ®

QM87 chipset and supports the new BGA1364 type. This board has lots of features, including supports total 4x SATA 6.0 Gbps storage specification , allows RAID 0/1/5 and 10. supports the latest PCIe 3.0 (one PCI-Express x16 slot) devices for double speed and bandwidth which enhances system performance, two long-DIMM memory slot for DDR3L SDRAM up to 16GB, support total 10 USB ports (4x USB 3.0 on rear I/O, 6x USB 2.0 on board header), VGA / HDMI / DVI-D / DP / LVDS, two

Gigabit Ethernet and Dual mini-PCIe slot support mSATA and normal storage.

WADE-8022 User’s Manual 1-1

System Overview

1.2 Check List

The WADE-8022package should cover the following basic items

9 One WADE-8022Mini-ITX Main Board

9 One SATA Cable

9 One I/O Shield bracket

9 One Installation Resources CD-Title

If any of these items is damaged or missing, please contact your vendor and keep all packing materials for future replacement and maintenance.

1.3 Product Specification

z Main Processor

Intel ® mobile BGA processor z Chipset

Intel ® QM87 chipset z System BIOS

AMI BIOS z Main Memory

Two 204 -pin DDR3 SODIMM socket support DDR3L up to 16GB dual channel

1333/1600 MHz memory z Expansion Interface

One PCIex16

- Two Mini-PCIe slot(support mSATA and normal SSD storage)

- One PCIe x1 gold finger(include 2x PCI x1 signal) z SATA Interface

Four SATA 6Gb ports z Serial Port

Support total six comports(one RS232 and one RS232/422/485 on rear I/O，three

RS232 and one RS232/422/485 on board header) z USB Interface

Support Ten USB (Universal Serial Bus) ports, four USB 3.0 ports on rear I/O and six USB 2.0 ports on board header for internal devices z Audio Interface

Line-Out Audio Jack on Rear I/O, Mic-In, Line-In on board header z Real Time Clock/Calendar (RTC)

Support Y2K Real Time Clock/Calendar


System Overview z Watch Dog Timer

Support WDT function through software programming for enable/disable and interval setting

- General system reset z On-board Ethernet LAN

Two Gigabit Ethernet (10/100/1000 Mbits/sec) LAN ports using Intel ®

WGI217LM

WGI210AT GbE Ethernet Controller z High Drive GPIO

One pin-header for 8 bit GPIO(4bit in & 4bit out) z System Monitoring Feature

Monitor system temperature and major power sources. z Outline Dimension (L x W)

170mm(6.69’’) x 170mm(6.69’’) z Power Requirements

System +12V

USB Loading Test (2.0)

USB Loading Test (3.0)

1.71 A 1.98 A

4.86 V/ 510 mA

4.82 V/ 970 mA

Full Loading

30Min

2.23 A z Configuration

CPU Type

SBC BIOS

EC Version

Memory

VGA Card

VGA Driver

LAN Card

LAN Driver

LAN Card

LAN Driver

Audio Card

Audio Driver

Chip Driver

USB 3.0 Driver

SATA HDD

DVDROM

Power Supply

Intel ® Celeron CPU 2000E @ 2.20GHz L3: 2Mbytes

Portwell, Inc. WADE-8022 TEST BIOS ( 40820T00 )

40717T00 ( 07/17/2014 )

WARIS DDR3L SO-DIMM 1600 1.35V/8GB*1

(Skhynix H5TC4G83AFR )

Onboard Intel ® HD Graphics

Intel ® HD Graphics Version: 10.18.10.3496

Onboard Intel ® Ethernet Connection I217-LM

Intel ® Ethernet Connection I217-LM Version: 12.11.96.1

Onboard Intel ® I210AT Gigabit Network Connection

Intel ® I210AT Gigabit Network Connection Version: 12.11.97.0

Onboard Realtek ALC886 High Definition Audio

Realtek ALC886 High Definition Audio Version: 6.0.1.7246

Intel ® Chipset Device Software Version: 9.4.0.1027

Intel ® USB3.0 eXtensible Host Controller Version: 6.2.9200.16384

WD WD1002FAEX 1TB

LION-ON IHAS324 DVD-ROM

Seasonic SSA-0651-1 DC 12V


System Overview z Operating Temperature

0 °C ~ 60 °C z Storage temperature

-20 ~ 80 °C z Relative Humidity

0% ~ 90%, non-condensing

1.3.1 Mechanical Drawing


System Overview


System Overview

1.4 System Architecture

All of details operating relations are shown in WADE-8022 System Block Diagram.

WADE-8022 User’s Manual

WADE-8022 System Block Diagram

1-6

Hardware Configuration

Chapter 2

Hardware Configuration

This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on WADE-8022 are in the proper position.





Jump Setting List

is mean default

JP1: GPIO Power select Connector

PIN No. Signal Description

1-2 5V

JP2: Dual channel LVDS VDD voltage Select

PIN No.

1-2

Signal Description

VDD voltage 3.3V (Default)　

5-6 VDD voltage 5V

JP3: LVDS BL Enable voltage Select

PIN No.

1-3, 2-4

1-3, 4-6

3-5,2-4


5V, Active High (Default)　

12V, Active High

5V, Active Low

3-5,4-6 12V, Active Low

JP4: WDT Function Select


1-2 short WDT Function enable (Default)

1-2 open WDT Function disable

JP5: ATX / AT Mode Select


1-2 short ATX emulation AT mode

1-2 open ATX mode 　



J9: Audio MIC/Line-in/Line-out Connector

PIN No.

1

3

5


MIC- in Left Channel

Analog Ground

Line-out Left Channel

7 Line-out Right Channel 8

J10: ATX 4Pin 12V Power Connector

PIN No.

2

4

6


Line-in Left Channel

Line-in Right Channel

Analog Ground

MIC- in Right Channel


1 Ground

2 Ground

3 +12V

4 +12V

J11: 8Bit GPIO Connector


5 LPC_GPJ2

7 LPC_GPJ3

J13: LVDS Power Connector


1 VCC

2 BL_BRIGHT

3 +12V

4 Ground

5 BL_ENABLE


2 LPC_GPE0

4 LPC_GPE7

6 LPC_GPC0

8 LPC_GPG0

10 VCC



J14: TPM(Trusted Platform Module) Connector


1 PCLK_TPM


2 GND

3 LFRAME# 4 N/C

5 SIO2_PLTRST# 6 VCC

7 LAD3

9 VCC3

8 LAD2

10 LAD1

11 LAD0 12 GND

13 SMB_CLK_MAIN 14 SMB_DATA_MAIN

15 3VSB

17 GND

16 SERIRQ

18 N/C

19 LPCPD#

J15: Dual channel LVDS Connector

20 N/C


1 VDD

3 LCD1DO0+

5 LCD1DO1+

7 LCD1DO2+

9 LCD1DO3+

11 LCD1CLK+

13 LCLK1

15 Ground

17 LCD2DO0+

19 LCD2DO1+

21 LCD2DO2+

23 LCD2DO3+

25 LCD2CLK+

27 N/C

29 Ground


2 VDD

4 LCD1DO0-

6 LCD1DO1-

8 LCD1DO2-

10 LCD1DO3-

12 LCD1CLK-

14 LDATA1

16 Ground

18 LCD2DO0-

20 LCD2DO1-

22 LCD2DO2-

24 LCD2DO3-

26 LCD2CLK-

28 N/C

30 Ground



J16/J17/J18/J19: COM3/COM4/COM5/COM6 Serial Port Connector

PIN No.

1

3

5

7

9

Signal Description PIN No. Signal Description

DCD (Data Carrier Detect) 2 RXD (Receive Data)

TXD (Transmit Data) 4 DTR (Data Terminal

Ready)

GND (Ground)

RTS (Request to Send)

RI (Ring Indicator)

J20: Clear CMOS

6

8

10

DSR (Data Set Ready)

CTS (Clear to Send)

N/C


1-2 Normal　

J22/J26: SATA Power Connector

Pin No. Signal Description

1 +12V

2 GND

3 GND

4 VCC



J23/J24/J25: External USB Connector

PIN No.

1


5V Dual

3 USB-

5 USB+

7 Ground

9

J27: SMBus Connector


2 5V Dual

4 USB-

6 USB+

8 Ground

10 N/C


1 SMBus_CLK

2 N/C

3 Ground

4 SMBus_DAT

5 +5V

J32: SYSTEM FAN Power Connector

2

3


Fan speed control

Fan on/off output



J37: Front Panel System Connector

5


1 PWR_LED(+)

3 PWR_LED(-)

J4 LAN1_ACT(+)

11 J5 LAN2_ACT(+)

13 HDD_LED(+)

15 HDD_LED(-)

J38: CPU FAN Power Connector


2 Speaker(+)

4 GND

6 N /C

8 Speaker(-)

10 GND

12 Power Button

16 GND


1 Ground

2 +12V

3 Fan on/off output

4 Fan Speed control

J39:PS/2 Keyboard/Mouse Pin Header

PIN No.

1


Mouse Data

3 N/C

5 Ground

7

9

PS2 Power

Mouse Clock

PIN No.

2


Keyboard Data

4 N/C

6 Ground

8

10

PS2 Power

Keyboard Clock



J41: SPI Bus Select Header

PIN No.

1-3, 2-4, 7-9, 8-10


CFEX

3-5, 4-6, 9-11, 10-12 Normal　

SW1: LVDS GPIO Switch Select

ON : 0 ; OFF : 1

Default : 0001

Pin No. Signal Description

1 GP0

2 GP1

3 GP2

4 GP3



J2

J3

J4

I/O peripheral devices are connected to the interface connectors.

Connector Function List

Connector Function Remark

J5

Audio Line Out Connector

DVI-I Connector

Serial port Connector (Top-COM2,

Bot-COM1)

Display Port Connector (DP port)

COM2 Support 232/422/485

Support Dual (DVI-D,VGA)

Link

J7 USB/100+Giga Lan Connector

(LAN2) I210IT

J8 USB/100+Giga Lan Connector

(LAN1) I217LM

MIC/Line-in/

Line-out Connector

J10 ATX 4Pin 12V Power Connector

J11 8Bit

J13 LVDS Power Connector

J14

J15

J16、J17、J18、

J19

J20

J21

TPM(Trusted Platform Module)

Connector

Dual channel LVDS Connector

COM3/COM4/COM5/COM6

Serial Port Connector

Clear CMOS Select HEADER

PCI-E x16 Slot Support PCI-E Gen3

J22、J26 SATA Power Connector

J23、J24、J25 External USB Connector

J28

J29

J30、J31

J32

J33、J34、J35、

J36

J37

J38

J39

Mini PCIe Slot

Mini PCIe Slot

SO-DIMM Slot

System FAN Power Connector

SATA Connector(6Gb/s)

Front Panel System Connector

CPU FAN Power Connector

PS/2 Keyboard/Mouse Pin Header

Only Support Mini PCIe

Only Support mSATA

Only Support

DDR3L Memory



J40

J41

CFEX Card slot

SPI Select HEADER


System Installation

Chapter 3

System Installation

This chapter provides you with instructions to set up your system. The additional information is enclosed to help you set up onboard PCI device and handle Watch

Dog Timer (WDT) and operation of GPIO in software programming.

3.1 Intel

®

Haswell Processor

The Main Processor of the WADE-8022 is Intel ® Celeron Haswell 2000E 2.2GHz

Processor (BGA Type)

WADE-8022 can support 4th Generation Mobile Celeron/Core Haswell i3/i5/i7

Processors (BGA Type) by optional.

WADE-8022 provide 2 x 204 pin DIMM sockets (Dual Channel) which supports

Dual channel 1333 DDR3L-SO-DIMM (1.35V) Non-ECC (Error Checking and

Correcting), non-register functions as main memory. The maximum memory can be up to 16GB. Memory clock and related settings can be detected by BIOS via

SPD interface.

The 2 DIMMs per channel only supported in Quad-Core package (1333 MT/s only)

For system compatibility and stability, do not use memory module without brand. Memory configuration can be set to either one double-sided DIMM in one

DIMM socket or two single-sided DIMM in both sockets.


System Installation

Beware of the connection and lock integrity from memory module to socket.

Inserting improperly it will affect the system reliability.

Before locking, make sure that all modules have been fully inserted into the card slots.

Note:

To insure the system stability, please do not change any of DRAM parameters in

BIOS setup to modify system the performance without acquired technical information.

3.3 Installing the Mini-ITX Board Computer

To install your WADE-8022 into standard chassis or proprietary environment, please perform the following:

Step 1: Check all jumpers setting on proper position

Step 2: Install and configure CPU and memory module on right position

Step 3: Place WADE-8022 into the dedicated position in the system

Step 4: Attach cables to existing peripheral devices and secure it

WARNING

Please ensure that SBC is properly inserted and fixed by mechanism.

Note:

Please refer to section 3.3.1 to 3.3.4 to install INF/VGA/LAN/Audio drivers.

3.3.1 Chipset Component Driver

WADE-8022 uses Intel ® QM87 Lynx Point chipset. It’s a new chipset that some old operating systems might not be able to recognize. To overcome this compatibility issue, for Windows Operating Systems such as Windows 7, please install its INF before any of other Drivers are installed. You can find very easily this chipset component driver in WADE-8022 CD-title.


System Installation

3.3.2 Intel

®

Integrated Graphics Controller

WADE-8022 uses Intel ® PCH integrated graphic chipset to gain an outstanding graphic performance. WADE-8022 supports DP (3200 x 2000 resolution), HDMI

(4096 x 2304 resolution), LVDS (18/24bit single & Dual port, 1920x1200 resolution)from onboard Shark Bay BGA processor, DVI-I (DVI+VGA, 1920 x

1200 resolution) from QM87 PCH display output. Processor integrated 3D graphics Media Accelerator . Supports DX11.1, OpenGL 3.1, MPEG-2, Shader

Model 4.0. WADE-8022 can support triple display output.

Drivers Support

Please find the Graphic drivers in the WADE-8022 CD-title. Drivers support

Win7.

3.3.3 Gigabit Ethernet Controller

Drivers Support

Please find Intel ® WGI217LM and WGI210AT LAN drivers in /Ethernet directory of WADE-8022 CD-title. The drivers support Win7.

Please find ALC886 (High Definition Audio driver) form WADE-8022 CD-title.

The drivers support Win7.

The following table indicates how to enable/disable Clear CMOS Function hardware circuit by putting jumpers at proper position.

J20: Clear CMOS


1-2 Normal


System Installation

Sample code:

#include <stdio.h>

#include <stdlib.h>

#include <conio.h>

#include <dos.h>

#define EC_DATA 0x62

#define EC_CMD 0x66

#define EC_CMD_READ 0x80

#define EC_CMD_WRITE 0x81

#define WDT_MODE 0x06 /* WDT Select mode. */

#define WDT_MIN 0x07 /* Minute mode counter */

#define WDT_SEC 0x08 /* Second mode counter */

/* Use port 62 and port 66 to access EC command / data. */ static int IBF_Check()

{ unsigned char IBF_status;

do

{

delay(2);

outportb

} while (IBF_status & 0x02);

return

} static int OBF_Check ()

{ unsigned char OBF_status;

do

{

delay(2);

OBF_status = inportb (EC_CMD);

} while (!(OBF_status & 0x01));

} static void Write_EC (unsigned char index, unsigned char data)

{

(); outportb (EC_CMD, EC_CMD_WRITE);


System Installation

{ outportb (EC_DATA, index);

IBF_Check

outportb

} static unsigned char Read_EC (unsigned char address) unsigned char data;

(); outportb (EC_CMD, EC_CMD_READ);

();

(EC_DATA,

OBF_Check(); data = inportb (EC_DATA);

return

} void EC_WDT_Trigger ()

{

/* WDT Counter */

Write_EC (WDT_SEC, 0x05);

/* if use minute mode */

} int main ()

{

/* Write_EC (WDT_MIN, 0x05); */

/* 0x01 is second mode */

/* 0x03 is minute mode */

Write_EC (WDT_MODE, 0x01);

EC_WDT_Trigger for (i = 0; i < 5; i++)

{ printf ("Reset counter ...................%d\n", 5 - i);

(1000);

}

return

}


System Installation

Sample code:

#include <stdio.h>

#include <stdlib.h>

#include <conio.h>

#include <dos.h>

#define EC_DATA 0x62

#define EC_CMD 0x66

#define EC_CMD_READ 0x80

#define EC_CMD_WRITE 0x81

#define GPIO_DIR 0x2B

#define GPIO_DATA 0x2C static void Write_EC (unsigned char index, unsigned char data)

{

sleep(1); outportb (EC_CMD, EC_CMD_WRITE);

sleep(1); outportb (EC_DATA, index);

sleep(1);

{

} static unsigned char Read_EC (unsigned char address) unsigned char data;

sleep(1); outportb (EC_CMD, EC_CMD_READ);

sleep(1);

(EC_DATA,

sleep(1); data = inportb (EC_DATA);

return

} int main ()

{ unsigned char d2;

printf("\n\n"); printf("WADE-8079 GPIO TEST Program v1.0\n"); printf("Please short the following pins with 2.54mm-pitched jumper on

JP8\n");


System Installation

----

printf("GPIO3

printf("GPIO5

printf("GPIO7 printf("GND xxxx Vcc <==PWR/GND pins, DO NOT short them!\n\n"); printf("LED Test Begins...\n");

/* Set GPIO Port In/Out mode */

Write_EC (GPIO_DIR, 0x00);

(2); printf("Write_EC mode 0x00\n");

/* Set Low or High */

Write_EC (GPIO_DATA, 0xFF); printf("Write_EC data 0xFF\n");

/* Set GPIO Port In/Out mode */

Write_EC (GPIO_DIR, 0x00);

sleep printf("Write_EC mode 0x00\n");

/* Set Low or High */

Write_EC (GPIO_DATA, 0x00); printf("Write_EC data 0x00\n");

(2);

return

}


BIOS Setup Information

Chapter 4

BIOS Setup Information

WADE-8022 uses AMI BIOS structure stored in Flash ROM. These BIOS has a built-in Setup program that allows users to modify the basic system configuration easily. This type of information is stored in CMOS RAM so that it is retained during power-off periods. When system is turned on, WADE-8022 communicates with peripheral devices and checks its hardware resources against the configuration information stored in the CMOS memory. If any error is detected, or the CMOS parameters need to be initially defined, the diagnostic program will prompt the user to enter the SETUP program. Some errors are significant enough to abort the start up.

4.1 Entering Setup - Launch System Setup

Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <Del> key will enter BIOS setup screen.

Press <Del> to enter SETUP

If the message disappears before responding and still wish to enter Setup, please restart the system by turning it OFF and On or pressing the RESET button. It can be also restarted by pressing <Ctrl>, <Alt>, and <Delete> keys on keyboard simultaneously.

Press <F1> to Run SETUP or Resume

The BIOS setup program provides a General Help screen. The menu can be easily called up from any menu by pressing <F1>. The Help screen lists all the possible keys to use and the selections for the highlighted item. Press <Esc> to exit the

Help screen.



4.2 Main

Use this menu for basic system configurations, such as time, date etc.

BIOS Information, Memory Information

These items show the firmware and memory specifications of your system. Read only.

System Date

The date format is <Day>, <Month> <Date> <Year>. Use [＋] or [－] to configure system Date.

System Time

The time format is <Hour> <Minute> <Second>. Use [＋] or [－] to configure system Time.



4.3 Configutation

Use this menu to set up the items of special enhanced features.

CPU Configuration

CPU Configuration Parameters



Active Processor Cores

Number of cores to enable in each processor package

Choices: All, 1.

Intel ® Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

Choices: Disabled, Enabled.

EIST

Enable/Disable Intel ® SpeedStep.


CPU C states

Enable or disable CPU C states


Enhanced C1 states (CPU C states Enabled)

Enhance C1 state


CPU C3 Report (CPU C states Enabled)

Enable/Disable CPU C3 report to OS







Choices: Disabled, CPU C7, CPU C7s.



Chipset Configuration

Configuration Chipset feature

High Precision Timer

Enable or Disable the High Precision Event Timer.


Azalia

Control Detection of the Azalia Device.

Disabled = Azalia will be unconditionally disabled.

Enabled = Azalia will be unconditionally Enabled.


Port 80h Redirection

Control where the Port 80h cycles are sent

[LPC BUS] Forward I/O Port 80 to LPC

[PCIE BUS] Forward I/O Port 80 to PCIE Subtractive device

Choices: LPC BUS, PCIE BUS.



AMT Configuration

Configure Active Management Technology Parameters

Intel ® AMT

Enable/Disable Intel ® Active management technology BIOS Extension

Note: iAMT H/W is always enabled.

This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device


Un-configure ME

OEMFlag Bit 15: Un-configure ME without password.


Disable ME

Set ME to Soft Temporary Disabled.




Memory Configuration

Memory Configuration Parameters (Read Only)

LAN Configuration

Configuration On Board LAN device.



Launch PXE OpROM policy

Controls the execution of UEFI and Legacy PXE OpROM

Choices: Disabled, UEFI only, Enabled.

Intel ® LAN I217 Controller

Enable or disable onboard NIC.

Choices: Enabled, Disabled.

Wake on LAN I217

Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.)


Intel ® LAN I210 Controller

Enable or disable onboard NIC.


Wake on LAN I210

Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.)


Graphic Configuration

Configuration Graphics Settings



Primary Display

Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.

Choices: Auto, IGFX, PEG, PCIE.

Primary PCIE

Select PCIE4/PCIE5 Graphics device should be Primary PCIE.

Choices: Auto, PCIE4, PCIE5.

Aperture Size

Select the Aperture Size.

Choices: 128MB, 256MB, 512MB.

DVMT Pre-Allocated

Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the

Internal Graphics Device.

Choices: 32M, 64M, 96M, 128M, 160M, 192M, 224M, 256M, 288M, 320M, 352M,

384M, 416M, 448M, 480M, 512M, 1024M.

DVMT Total Gfx Mem

Select DVMT 5.0 Total Graphic Memory size used by the Internal Graphic device.

Choices: 128M, 256MB, MAX.

Primary IGFX Boot Display

Select the Video Device which will be activated during POST. This has no effect if external graphics present.

Secondary boot display will appear based on your selection. VGA modes will be supported only on primary display.

Choices: VBIOS Default, VGA, DP, LVDS, DVI HDMI.

Secondary IGFX Boot Display

Select Secondary IFGX Boot Display Device.

Choices: Disabled, DP, LVDS, DVI, HDMI.



PCI/PCIE Configuration

PCI, PCI-X and PCI Express Settings.

PCI Latency Timer

Value to be programmed into PCI Latency Timer Register

Choices: 32 PCI Bus Clocks, 64 PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus

Clocks, 160 PCI Bus Clocks, 192 PCI Bus Clocks, 224 PCI Bus Clocks, 248 PCI Bus

Clocks.

Maximum Payload

Set Maximum Payload of PCI Express Device or allow System BIOS to select the value.

Choices: Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, 4096 Bytes.

Maximum Read Request

Set Maximum Read Request size of PCI Express Device or allow System BIOS to select the value.

Choices: Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, 4096 Bytes.



CPU PCI Express Configuration

CPU PCI Express Configuration settings

PEG0 – Gen X

Configure PEG0 B0:D1:F0 Gen1-Gen3

Choices: Auto, Gen1, Gen2, Gen3

PEG0 – ASPM

Control ASPM support for the PEG Device. This has no effect if PEG is not the currently active device.

Choices: Disabled, Auto, ASPM L0s, ASPM L1, ASPM L0sL1.

PEG1 – Gen X



PEG1 – ASPM



PEG2 – Gen X





PEG2 – ASPM



Enable PEG

To enable or disable the PEG

Choices: Disabled, Enabled, Auto.

PCH PCI Express Configuration

PCH PCI Express Configuration settings



PCI Express Root Port 1-5, Port8

PCI Express Root Port 1-5 Settings Port 1-5, Port8 (x1)

PCI Express Root Port 1-5, Port8

Control the PCI Express Root Port


ASPM

PCI Express Active State Power Management settings

Choices: Disabled, L0s, L1, L0sL1, Auto

PCIe Speed

Select PCI Express port speed.

Choices: Auto, Gen1, Gen2.



SATA Configuration

SATA Device Options Settings

SATA Controller(s)

Enable or disable SATA Device.




SATA Mode Selection

Determines how SATA controller(s) operate.

Choices: IDE, AHCI, RAID.

SATA Controller Speed

Indicates the maximum speed the SATA controller can support.

Choices: Default, Gen1, Gen2, Gen3.

Alternate ID (RAID Mode only)

Report alternate Device ID


Port 0-5

Enable or Disable SATA Port


Hot Plug

Designates this port as Hot Pluggable


Mechanical Presence Switch (For Serial ATA Port 0-3 only)

Controls reporting if this port has an Mechanical Presence Switch.

Note: Requires hardware support.


External SATA

External SATA Support


SATA Device Type

Identify the SATA Port is connected to Solid State Drive or Hard Disk Drive.

Choices: Hard Disk Drive, Solid State Drive.



USB Configuration

USB Configuration Parameters

Legacy USB Support

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for

EFI applications.

Choices: Enabled, Disabled, Auto.

XHCI Hand-Off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should claim by XHCI driver.


EHCI Hand-Off

This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should claim by EHCI driver.


USB Mass Storage Driver Support

Enable/Disable USN Mass Storage Driver Support.




PCH USB Configuration

PCH USB Configuration settings

USB Port #0-11

Disable USB Port




Power Control Configuration

System Power Control Configuration Parameters

Enable Hibernation

Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.


ACPI Sleep State

Select the ACPI Sleep state the system will enter when the SUSPEND button is pressed.

Choices: S3 only (Suspend to RAM).

Power Loss Function

Control SIO Power Loss Function, ON is always ON, OFF is always OFF, Last state will depends on last power state.

Choices: Always Off, Always On, Last State.

Wake system with Fixed Time

Enable or disable system wake on alarm event. When enabled, System will wake on the hr::min::sec specified.




Wake up Day of Month

Select 0 for daily system wake up 1-31 for which day of the month that you would like the system wake up.

Choices: 1-31.

Wake up hour

Select 0-23 for example enter 3 for 3am and 15 for 3pm.

Choices: 0-23.

Wake up minute

Choices: 0-59.

Wake up second

Choices: 0-59.

Wake up Ring

Enable or Disable Wake on Ring form OS.


TPM Configuration

Trusted Computing Settings



Security Device Support

Enables or Disables BIOS support for security device. O.S. will not show Security

Device. TCG EFI protocol and INT1A interface will not be available.

Choices: Disable, Enable.

Super IO Configuration

System Super IO Chip Parameters

Watch Dog Timer

Enable/Disable Watch Dog Timer


Timer Unit

Select Timer count unit of WDT.

Choices: Second, Minute.

Timer value

Select WDT Timer value Seconds Range: 10 to 255

Choices: 10-255.

Serial Port 1-6

Enable or Disable Serial Port 1-6 (COM)




RS-232/422/485 Control Option (For Serial Port2 only)

Serial Port2 RS-232/422/485 Control Option

Choices: RS-232, RS-422, RS-485.

H/W Monitor

Monitor hardware status

CPU Smart Fan Control

Control Which Mode for CPU Smart Fan use.

Choices: Disabled, Thermal Cruise Mode.

Smart Fan Start Temperature

Set Temperature for Start CPU Smart Fan (40 to 105)

Choices: 40-105

Smart Fan Full Speed Temperature

Set Temperature for Smart Fan Full Speed (40 to 105)

Choices: 40-105



Serial Port Console Redirection

Serial Port Console Redirection

Serial Port 1 (Disabled)

Console Redirection

Console Redirection Enable or Disable


Serial Port 2 (Disabled)

Console Redirection

Console Redirection Enable or Disable




4.4 Boot

Bootup Num-Lock State

Select the keyboard Numlock state.

Choices: On, Off.

GateA20 Active

UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disabling GA20; this option is useful when any RT code is executed above

1MB.

Choices: Upon Request, Always.

Option ROM Messages

Set display mode for Option ROM.

Choices: Force BIOS, Keep Current.

INT19 Trap Response

BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE – execute the trap right away; POSTPONED – execute the trap during legacy boot.

Choices: Immediate, Postponed.



Launch Storage OpROM

BIOS reaction on INT19 trapping by Option ROM:

IMMEDATE – execute the trap right away; POSTPONED – execute the trap during legacy boot.

Choices: Immediate, Postponed.

Full Screen Logo

Enables or Disables Quiet Boot option and Full screen Logo.


Post Report

Post Report Support Enabled/Disabled.


Summary Screen

Summary Screen Support Enabled/Disabled.


Fast Boot

Enables or Disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options.

Choices: Disable Link, Enabled.

Boot mode select

Select boot mode LEGACY/UEFI.

Choices: LEGACY, UEFI.

Boot Option #1-7

Sets the system boot order

Choices: Hard Disk, CD/DVD, USB Hard Disk, USB CD/DVD, USB Key, USB

Floppy, Network, Disabled.



4.5 Security

Administrator Password

Set Setup Administrator Password

User Password

Set User Password



4.6 Save & Exit

Save Changes and Reset

Reset the system after saving the changes.

Pressing <Enter> on this item asks for confirmation: Save configuration and reset.

Discard Changes and Exit

Reset system setup without saving any changes.

Restore Defaults

Restore/Load Default values for all the setup options.


Troubleshooting

Chapter 5

Troubleshooting

This chapter provides a few useful tips to quickly get WADE-8022 running with success. As basic hardware installation has been addressed in Chapter 2, this chapter will primarily focus on system integration issues, in terms of BIOS setting, and OS diagnostics.

5.1 Hardware Quick Installation

ATX Power Setting

Unlike other Mini-ITX board computer, WADE-8022 supports ATX only. Therefore, there is no other setting that really needs to be set up. You must connect to J1 (12V DC

Jack) or J10 (ATX 4Pin 12V Power Connector) to let WADE-8022 power on.

ATX Power emulation AT Mode

You can adjust the JP5 to 1-2 short to emulation the AT mode.

It can let system auto power on when J1 or J10 has been detected your power source directly.

JP5: ATX / AT Mode Select


1-2 short ATX emulation AT mode

1-2 open ATX mode

Please note that you still need to use 12V adapter or ATX power supply to use!!

Serial ATA Hard Disk Setting for IDE/AHCI/RAID

Unlike IDE bus, each Serial ATA channel can only connect to one SATA hard disk at a time; there are total four connectors, J33, J34, J35, J36 SATAIII (6Gb/s) ports on-board.

The SATA hard disk doesn’t require setting up Master and Slave, which can reduce mistake of hardware installation. All you need to operate IDE, AHCI or RAID

(0,1,5,10) application for system, please follow up setting guide in BIOS programming (Table 5-1); Furthermore, you can consult chapter 4.3

Advanced “SATA Configuration” part of the” SATA Mode Selection”.


Troubleshooting

Table. 5-1 SATA Mode setting guide

System BIOS Main Menu

Configuration

SATA Configuration

CFEX support

SATA Mode Selection …….………… [Press enter]

SATA Mode…… [IDE/AHCI /RAID Mode]

The J40 (CF 50pin socket) supports CFEX. (Has SATA signal).

mSATA device support

The J28 (Mini-PCIe slot) has SATA signal can support mSATA device.


Troubleshooting

It is assumed that users have correctly adopted modules and connected all the devices cables required before turning on ATX power. 204-pin DDR3 SO-DIMM

Memory, keyboard, mouse, SATA hard disk, DVI-I connector, device power cables,

ATX accessories are good examples that deserve attention. With no assurance of properly and correctly accommodating these modules and devices, it is very possible to encounter system failures that result in malfunction of any device.

To make sure that you have a successful start with WADE-8022, it is recommended, when going with the boot-up sequence, to hit “Del” or “Esc” key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well.

Loading the default optimal setting

When prompted with the main setup menu, please scroll down to “Restore

Defaults”, press “Enter” and select “Yes” to load in default optimal BIOS setup. This will force your BIOS setting back to the initial factory configuration. It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed. As a matter of fact, users can load the default BIOS setting any time when system appears to be unstable in boot up sequence.

Improper Disable Operation

There are too many occasions where users disable a certain device/feature in one application through BIOS setting. These variables may not be set back to the original values when needed. These devices/features will certainly fail to be detected.

When the above conditions happen, it is strongly recommended to check the BIOS settings. Make sure certain items are set as they should be. These include the Serial

Port1/ Serial Port 2 ports, USB ports, external cache, on-board VGA and Ethernet.

It is also very common that users would like to disable a certain device/port to release IRQ resource. A few good examples are

Disable Serial Port1 to release IRQ #4

Disable Serial Port2 to release IRQ #3

Etc…

A quick review of the basic IRQ mapping is given below for your reference.

It is then very easy to find out which IRQ resource is ready for additional peripherals.

If IRQ resource is not enough, please disable some devices listed above to release further IRQ numbers.


Troubleshooting

5.3 FAQ

Information & Support

Question: I forget my password of system BIOS, what am I supposed to do?

Answer: You can simply short 2-3 pins on J20 to clean your password.

Question: How to update the BIOS file of the WADE-8022?

Answer:

1. Please visit web site of the Portwell download center as below hyperlink and register an account. (The E-Mail box should be an existing

Company email address that you check regularly.) http://www.portwell.com.tw/member/newmember.php

2. Input your User name and password to log in the download center.

3. Select the “Search download” to input the keyword “WADE-8022”.

4. Find the “BIOS “page to download the ROM file and flash utility.

5. Execute the zip file to root of the bootable USB pen drive which can boot to DOS mode.

6. Insert your bootable USB pen drive in WADE-8022 board and power-on.

7. Boot to DOS mode then input the “Update” command to start to update

BIOS process.

8. Switch “Off” the Power Supply when you finished the update process.

9. Wait 5 seconds then switch “ON” the Power Supply then press the “Del” or “Esc” key to BIOS to select “Load Setup Defaults” and then select “Exit

Saving Changes” option.

Note:

Please visit our Download Center to get the Catalog, User manual, BIOS, and driver files. http://www.portwell.com.tw/support/download_center.php

If you have other additional technical information or request which is not covered in this manual, please fill in the technical request form as below hyperlink. http://www.portwell.com.tw/support/problem_report.php

We will do our best to provide a suggestion or solution for you.


Troubleshooting

System Memory Address Map

Each On-board device in the system is assigned a set of memory addresses, which also can be identical of the device. The following table lists the system memory address used for your reference.

Memory Area Size Description

0000 – 003F

0040 – 004F

0050 – 006F

1K

0.3K

0.5K

Interrupt Area

BIOS Data Area

System Data

0070 – 0E2E

0E2F - 0F6B

54K

5K

DOS

Program Area

0F6C – 9D7F 568K 【 Available】

First Meg -- Conventional memory end at 630K --

9D80 – 9EFF

9F00 – 9FFF

A000 - AFFF

B000 – B7FF

B800 - BFFF

C000 - CEBF

CEC0 - EFFF

F000 - FFFF

6K

4K

64K

32K

32K

59K

133K

64K

Extended BIOS Area

Unused

VGA Graphics

Unused

VGA Text

Video ROM

Unused

System ROM

HMA 64K First 64K Extended


Troubleshooting

IRQ 7

IRQ 8

IRQ 9

IRQ 10

IRQ 11

IRQ 12

IRQ 13

IRQ 14

IRQ 15

Interrupt Request Lines (IRQ)

Peripheral devices can use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.

Interrupt Request Lines IRQ

IRQ# Current Use Default Use

IRQ 0

IRQ 1

System ROM

System ROM

System Timer

Keyboard Event

IRQ 2

IRQ 3

IRQ 4

IRQ 5

IRQ 6

【

【

Unassigned】

System ROM

System ROM

Unassigned】

System ROM

Usable IRQ

COM2

COM1

Usable IRQ

Diskette Event

【 Unassigned】

System ROM

【 Unassigned】

Video ROM

【 Unassigned】

System ROM

System ROM

System ROM

【 Unassigned】

Usable IRQ

Real-Time Clock

Usable IRQ

Usable IRQ

Usable IRQ

IBM Mouse Event

Coprocessor Error

Hard Disk Event

Usable IRQ


Portwell WADE-8022 User manual

Mini-ITX Board

Table of Contents

How to Use This Manual

Chapter 1

System Overview

1.1 Introduction

1.2 Check List

1.3 Product Specification

1.4 System Architecture

Chapter 2

Hardware Configuration

Chapter 3

System Installation

3.1 Intel

Haswell Processor

3.3 Installing the Mini-ITX Board Computer

Chapter 4

BIOS Setup Information

4.1 Entering Setup - Launch System Setup

4.2 Main

4.3 Configutation

4.4 Boot

4.5 Security

4.6 Save & Exit

Chapter 5

Troubleshooting

5.1 Hardware Quick Installation

5.3 FAQ

Related manuals

Table of contents

Portwell WADE-8022 User manual

Mini-ITX Board

Table of Contents

How to Use This Manual

Chapter 1

System Overview

1.1 Introduction

1.2 Check List

1.3 Product Specification

1.4 System Architecture

Chapter 2

Hardware Configuration

Chapter 3

System Installation

3.1 Intel

Haswell Processor

3.3 Installing the Mini-ITX Board Computer

Chapter 4

BIOS Setup Information

4.1 Entering Setup - Launch System Setup

4.2 Main

4.3 Configutation

4.4 Boot

4.5 Security

4.6 Save & Exit

Chapter 5

Troubleshooting

5.1 Hardware Quick Installation

5.3 FAQ

Related manuals

Portwell

WADE-8078

WinSystems

ITX-N-3815-1-0

Portwell

WADE-8076

Portwell

WADE-8070

Table of contents