Onetouch 32-4W 232, USB, 5W 232, 5W USB-BB TouchScreen Controller User Manual
Below you will find brief information for TouchScreen Controller 32-4W 232, TouchScreen Controller 32-4W USB, TouchScreen Controller 5W 232, TouchScreen Controller 5W USB-BB. These touch panel controllers offer a superior design with high sensitivity, accuracy, and user-friendly operation. This manual will guide you through the installation, configuration, and advanced features of the TouchKit software, including mouse emulation, monitor rotation, and sound notification.
Advertisement
Advertisement
TouchScreen Controller
User Manual for Windows 9X / ME
Version: 3.4.0
Customer :
Model :
32-4W232/4WUSB/5W232/5WUSB-BB
Date :
Version:
Onetouch Technologies
Co., Ltd.
(Supplier)
Acceptance Sheet
(Purchaser)
Date Approval Signature Date Approval Signature
O netouch
®
Model No.
Page
1
CONTENT
CHAPTER 1. TOUCH PANEL CONTROLLER.............................................................. 3
1.1 CONTROLLER .................................................................................................. 3
1.2 SPECIFICATIONS AND FEATURES............................................................... 4
CHAPTER 2. INSTALLING TOUCHKIT......................................................................... 6
CHAPTER 3. CONFIGURATION UTILITY AND RIGHT BUTTON EMULATOR..10
CHAPTER 4. MONITOR ROTATION SETTING…………………………..………… 27
4.1 ROTATING DISPLAY BY WAY OF NVIDIA OR ATI DRIVER….…...…..27
4.2 ROTATING DISPLAY BY WAY OF PIVOT DRIVER……………….……..28
CHAPTER 5. UNINSTALLING TOUCHKIT.................................................................. 31
O netouch
®
Model No.
Page
2
Chapter 1. Touch Panel Controller
This touch panel controller provides the optimistic performance of analog resistive touch panels for 4 wire, 5 wire and models. It communicates with PC system directly through RS232, PS/2 or USB connector. Users can see how superior the design is in sensitivity, accuracy and friendly operation. The touch panel driver emulates mouse left and right button function and supports operation systems including Microsoft Windows 95 / 98 / ME /NT4 / 2000 / XP / XP Tablet PC Edition,
Windows CE 2.12 / 3.0 / .NET, Linux, iMac and DOS.
1.1 Controller
Interface RS232 USB PS/2
4-wire Ready Ready Ready
5-wire Ready Ready Ready
Table 1. Controllers match with different interfaces
O netouch
®
Model No.
Page
3
O netouch
®
Specifications
Power requirements
Operating temperature
Storage Temperature
Relative Humidity
Protocol
Resolution
Report rate
Response time
Pin out definition
Panel resistance
Regulatory Approvals
1.2 Specifications and Features
+5VDC ( Maximum 100mA, typical 70mA,
50mV peak to peak maximum ripple )
0 to 50 ℃
-40 to 80 ℃
RS232 Model: 9600 bauds, None parity, 8 data bits and 1 stop bit
USB Model: USB 1.1 Low speed
PS/2 Model: PS/2 mouse
2048 X 2048
RS232 Model: Max. 160 points/sec
USB Model: Max. 160 points/sec
PS/2 Model: Max. 140 points/sec
Resistive: Max. 35 ms
Capacitive: Max. 20 ms
Resistive: Max. 35 ms
Capacitive: Max. 20 ms
4 wire model: X+, Y+, X-, Y-
5 wire model: UL, UR, COM, LR, LL
4, wire resistive model: 200 ~ 900 ohm
( pin to pin on the same layer )
5 wire resistive model: 50 ~ 200 ohm
( pin to pin on drive layer )
FCC-B, CE
Table 2. Specifications for TouchKit controller
Model No.
Page
4
Features
Calibration
Compensation
Draw Test
Language
Advanced Feature
Controller Setting
Mouse Emulator
Sound Notification
Double Click
OS support
COM port support
O netouch
®
Model No.
Fast full oriental 4 points position
Accuracy 25 points linearity compensation.
Position and linearity verification
Support 10 languages for Windows
1. Support monitor / display rotation
2. Support multiple monitor / display
3. Support QVGA and Half-VGA function
4. Support edge compensation
5. Support constant touch
1. Support multiple controllers
2. Dynamical add / remove controllers
3. Change Controller interface without reboot.
1. Right / Left button emulation
2. Normal / Click on touch / Click on release mode
3. Auto right button
1. Sound option (No Sound / Touch Down /
Lift Up)
2. Frequency adjustment
3. Duration adjustment
1. Configurable double click speed
2. Configurable double click area
1. Windows 95 / 98 / ME / NT4 / 2000 / XP /
Windows XP Tablet PC Edition
2. Windows CE 2.12 / 3.0 / .NET
3. Linux ( RedHat / Fedora / Mandrake /
Suse / YellowDog )
4. iMac. OS9.X / OSX
5. MS-DOS:
Support display resolution:
320x200, 640x200, 640x350, 640x480,
800x600,
1024x768 and 1280x1024
1. Support COM 1 ~ COM 256 for Windows and Linux
2. Support COM 1 ~ COM 8 for DOS
Table 3. Features for TouchKit software
Page
5
Chapter 2. Installing TouchKit
TouchKit is software, which contains drivers of the touch panel controllers for the specified communication connectors, RS232, PS/2 and USB, and the other two utilities:
• Touch Tray support
This is utility for emulating the right and left button of mouse through controlling
Touch panel. Users can toggle between right or left mouse buttons by this utility.
• Configuration support
The calibration and draw test of touch panel are done by this utility. Besides, users can add or remove for new RS-232, PS/2 or USB touch panel devices.
Follow these steps to install TouchKit.
1. Put the TouchKit CD to CD-ROM.
2. Change directory to Win9X_ME
3. Double click the Setup.exe, then windows starts to run the installation program.
Notice that do not plug the USB controller on the system before the installation
has been finished.
4. Just click [Next >] button to continue installation.
O netouch
®
Model No.
Page
6
5. Then check the check box if PS/2 touch controller is to be installed. The default
is unchecked. Then Press [Next >] to continue installation.
System will give you a warning, if users check the PS2AUX check box,
6. Choose the setup type that best suits your needs. There are two TouchKit
accessory utilities for choosing, Rotation Monitor Utility and Shutdown Utility.
Users can install the utility they want by checking the box. Then Press [Next >]
to continue installation.
O netouch
®
Model No.
Page
7
7. Select the appropriate folder where set-up files will be installed. Then Press
[Next >] to continue installation.
8. Then type in the name of program folder for TouchKit or press [Next >] to
continue. There will be a default name for it.
During driver installation, the setup program will scan COM port for RS232
Touchkit controller. Once the controller was scanned, the setup program will
display a dialog as
Click Yes to add the controller on the specified COM port automatically.
O netouch
®
Model No.
Page
8
9. Windows is copying files to disk and the setup is complete. It will request re-boot
computer. Press [Yes >] to re-boot immediately or [No >] to re-boot later. The
installation will not be finished until system re-boot.
10. Setup is complete. After TouchKit installation, the USB device will be found
automatically as soon as it was plugged into the computer. Then users can see
the new device on the application program window. And, the program will remove
the USB Device automatically as soon as it was unplugged. ( USB device is not
supported for Windows95 )
O netouch
®
Model No.
Page
9
Chapter 3. Configuration Utility and Right Button Emulator
There are five property pages in TouchKit utility, and they are General, Setting,
Edge coefficient, Monitors and About. Each property page contains different
functions for users to do the adjustments. Therefore, users can easily manage all the
TouchKit controllers through TouchKit utility.
Functional Group Tab
General
General property page contains the functions of language selection, devices add/
remove, 4 points calibration, Draw test and Advanced.
General Function
O netouch
®
Model No.
Page
10
<Language>
TouchKit supports multi-language user interface. Users could select native
language that is compatible to operation system support. For example, if the
operation system is a traditional Chinese version, users could see the normal
display words under the traditional Chinese and English mode. There are ten
different languages, English, Traditional Chinese, Simplified Chinese,
French, Spanish, German, Japanese, Italian, Korean and Dutch supported in
this feature of TouchKit.
Note to select the
compatible language first.
Select the compatible language first or users may not see the normal display of
each button.
<Add> / <Remove>
Please check the touch panel devices (including its controller) are equipped well,
then click [Add] button to add all of those RS-232 and PS/2 devices to the Panel
List dialogue box.
There is one devices found. Press [Yes] to continue.
O netouch
®
Model No.
Page
11
Device is found in COM1
The controller is displayed on the Panel List box. users can get the information
of interface, type, firmware version and baud rate for each controller.
Select one device after added more than one device at the panel list window.
The one selected will activate the panel, and remember to do the calibration
before starting to use touch panel.
But, for hot-swapping USB touch controller, it will be added automatically as
soon as it was plugged into the computer. Then users can see the new device
on the application program window. And, the program will remove the USB touch
controller automatically as soon as it was unplugged. ( USB device is not
supported for Windows95 )
O netouch
®
Model No.
Page
12
There are three buttons, [4pts Cal] [Draw Test] [Advanced], at the lower section of
the General property page.
<4pts Cal>
Correct 4 point locations on screen with the panel. Press [4 pts Cal], screen
displays as follows.
Touch the blinking symbol on panel until beep or stop blinking.
Touch the blinking symbol on panel until beep or stop blinking.
O netouch
®
Model No.
Page
13
<Draw Test>
Test the drawing position related to the display screen on panel.
Click on the [Draw Test] button. There will be a squared blue display showing.
In drawing test window, users can click [Clear] button to clear the window. Also,
users can click [Quit] or press mouse right button to quit from the drawing test.
In drawing test window, users can verify the panel linearity, calibration capability,
and drawing line quality.
<Advanced>
Touchkit provide more accuracy 25 points calibration for touch sensor. In
addition, Touchkit provides controller setting for capacitive touch sensor. If the
capacitive controller is selected, a capacitive setting property page appears on
the advanced sheet. In general case, it does not need to do 25 points calibration
other then bad linearity sensor.
Press [Clear] to clear the previous calibration records.
O netouch
®
Model No.
Page
14
Press [Yes] to clear previous records.The record will become default record.
Press [25ptCal] to do 25 points calibration. Correct 25 point locations on screen
with the panel.
Touch the blinking symbol on panel until beep or stop blinking.
After the calibration, the new record will overwrite the old one.
If the selected controller is capacitive type, an extra property page for capacitive
setting adjustment shown as below:
Please select property size of capacitive screen first, and press [Restart]
O netouch
®
Model No.
Page
15
The capacitive controller will restart, and do not touch the screen before the warning message disappears
Warming: Do not adjust the sensitive and sampling time without RD help
Setting
There are three functional groups in Setting property page, and at the upper section
of the property page is sound option; at the middle section is Mouse Mode; and at
the lower section is Double Click Adjustment.
The Sound options provide users the click feedback while touching the panel.
Select preferred option first.
Sound options
<No Sound>
Users could choose to make no sound while using the touch panel.
<Touch Down>
The system will make a sound while touching the panel.
<Lift Up>
The system will not make any sound until finger leaves the touch panel.
<Frequency>
Sound frequency, drag the cursor from left to right is low to high.
<Duration>
Sound duration, drag the cursor from left to right is short to long.
O netouch
®
Model No.
Page
16
The Mouse Mode provides users different operating options. They are as follows:
Mouse Mode
<Mouse Button>
Click it to show / hide Touch Tray on the right bottom corner of the desktop.
The touch panel system starts with the computer booting, and a mouse icon shows in the taskbar.
Users can choose show or hide Touch Tray from the mouse icon in the taskbar.
Just click the mouse icon to choose show or hide.
Touch Tray
Change right / left button by clicking the upper small rectangular box of Touch
Tray. Blue area expresses what button has been selected.
O netouch
®
Model No.
Page
17
<Shutdown utility>
Shutdown utility
Click on shutdown utility in the task bar
Shutdown utility dialog
There are five modes in shutdown utility for users convenience.
[Standby] to enter standby mode that saves power consumption.
[Shutdown] to turn off PC.
[Reboot] to restart PC.
[Cancel] to escape from the Shutdown utility dialog.
[Exit] to disable the Shutdown utility.
Please notice that Windows NT does not support this function.
<Mouse Mode>
There are three kinds of mouse mode users could choose,
[Normal Mode]
It provides all the mouse functions, including the dragging function.
[Click on Touch]
Click action is executed as soon as users touch the panel.
[Click on Release]
Click action will not be executed until finger leaves the panel.
O netouch
®
Model No.
Page
18
<Option>
Touchkit provides an option for advanced Mouse Emulation setting. When the
Option button is pressed, a setting property sheet will be popped up. Support
Constant Touch and Support Auto Right Button check boxes are shown in the property sheet to enable / disable Constant touch and Auto right button support.
[Constant Touch]
Enable Constant Touch to force driver to stop reporting touch point when the movement is within the range which users can adjust. Therefore, the user can see a stabilized cursor instead of a chattering cursor when users touch the same point with unwanted noise.
[Auto Right Button]
Enable Auto Right Button to force driver to report a right click mouse
event to OS when users do a continuing touch till time out. It no longer needs to touch the right button in the Touchtray to activate a right click.
This feature makes users to do right click more easily with touchscreen.
O netouch
®
Model No.
Page
19
<Cursor Visibility>
Cursor visibility function provides users to hide the cursor in the display. Please go to Start / Control Panel / Mouse / Pointers / Scheme, and choose
TouchKit Hide Cursor. Press [Apply] to make setting change, and press [OK] to escape the property page.
If users want to cancel the function of TouchKit Hide Cursor, do the steps again and choose the other scheme.
O netouch
®
Model No.
Page
20
The Double Click adjustment provides users to set up the tolerance while double clicking. They are as follows:
Double Click Adjustment
<Double Click Speed>
Double Click Speed is the double click response time for Windows system.
Users can adjust the proper double click for easy double click by touch panel.
<Double Click Area>
Each one touch has its own touch tolerance once someone may not fix in one point. So if users set the Double Click Area to <Smaller>, the panel will be very sensitive about micro-move while users want to fix on a point. If users set it to
<Larger>, it tolerates the larger touch point movement while users want to point at a fixed position.
O netouch
®
Model No.
Page
21
Edge Coefficient
Edge Coefficient property page contains the functions of Edge Compensation for
Top, Bottom, Left, Right, X Axis and Y Axis.
In some case, if it is difficult to touch items at the edges of the touch panel, users can set adjustment to reach the edges of the screen image.
O netouch
®
<Top>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the top edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the top edge.
<Bottom>
If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the bottom edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the bottom edge.
<Left>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the left edge. If users set the Edge to <Larger>, TouchKit will extend the vertical position of the left edge.
<Right>
If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the right edge. If users set the Edge to <Larger>, TouchKit will extend the vertical position of the right edge.
Model No.
Page
22
In some case, cursor will be behind the finger when users touch the panel. If users can not see the cursor when they touch down on the panel, users can set X Axis or Y
Axis to move the cursor.
<Offset X Axis>
If users set the Offset X Axis to <Smaller>, cursor will be moved a pixel of X
Axis to left. If users set the Offset X Axis to <Larger>, cursor will be moved a pixel of X Axis to right.
<Offset Y Axis>
If users set the Offset Y Axis to <Smaller>, cursor will be moved a pixel of Y
Axis to top. If users set the Offset Y Axis to <Larger>, cursor will be moved a pixel of Y Axis to bottom.
Edge Compensation Switch
<Edge Compensation Switch>
Users can choose Edge compensation Enable / Disable from left bottom corner of Touchkit Utility.
Using +10% and -10% button to adjust the smaller or larger of edge. If users press +10% button, the top, bottom, left and right edges will extend 10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to right and top. If users press -10% button, the top, bottom, left and right edges will contract 10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to left and bottom.
If users want the value back to the default value, choose Default button.
O netouch
®
Model No.
Page
23
Monitors
There are three functions in this property page, and they are Multiple Monitors,
Split Monitor and One point Calibration. Such a trendy and yet innovated design provides viewing pleasures, viewing flexibility and convenience to users.
<Multiple Monitors>
To configure the mapping relationship between the monitors and the touch panels, select the monitor page as below.
Set the check box (Use Multiple Monitors) to enable multiple monitors mapping.
Uncheck this box will disable multiple-monitor configuration, and all of the touch panel controllers will be mapped to the primary monitor. The gray shadow area is the monitor mapped the selected controller/panel. The button [Mapping] is used to find the mapping relationships between the monitors and touch panel controllers. Press the [Mapping], the software will guide users to touch the corresponding monitor to obtain the mapping relationship.
After finish monitor mapping, Press [Apply] to apply the mapping relation.
O netouch
®
Model No.
Page
24
<Split Monitors>
To use the Split Monitor function, users need to select which controller you want to launch this function, then check the Multiple Monitors box and Split Monitor at the same time as showing as the follow picture. Press the [Split Setting] button to set up the activate area.
O netouch
®
It shows the current resolution of display and users can set up the activate area by inputting the value by yourself or use the default button [Upper Half], [Left
Half] or [Quarter]. The default value of panel resolution should be full screen as
Left: 0 , Right: 0, Top: 0 and Bottom: 0.
<One Point Calibration>
TouchKit utility provides a fast tool to identify the touchscreen orientation when the monitor display was rotated by 90 degrees. Enable this One Point
Calibration feature, Touchtray will pops up this One Point Calibration tool for users to identify and correct the touchscreen / monitor orientation whenever the monitors was rotated by 90 degrees. Disable this feature, Touchtray does not pop up this One Point Calibration tool. Then, the user has to do four points calibration to correct the orientation whenever the monitor was rotated.
Model No.
Page
25
About
Information about TouchKit.
O netouch
®
Model No.
Page
26
Chapter 4. MONITOR ROTATION SETTING
TouchKit driver package for Windows 98/ME/2000/XP provides two easiest ways to rotate the touch panel while the display is rotated.
Rotating display by way of nVidia or ATI driver
Rotating display by way of Pivot.
4.1 Rotating display by way of nVidia or ATI driver
1. After activating the rotation of nVidia or ATI driver, there will be one blinking symbol show as the following picture. Touch near the blinking symbol until stop blinking, and the touch panel will rotate itself.
One touch blinking symbol adjustment
2. However, 180 degree rotation of touch panel can not be done in one step, users need to rotate 90 degree twice.
O netouch
®
Model No.
Page
27
4.2 Rotating display by way of Pivot
There are two ways to rotate the display by way of Pivot.
Rotating display by way of Pivot hotkey or function menu
Rotating display by way of RotTray icon provided by TouchKit.
< Rotating display by way of Pivot hotkey or function menu >
1. To rotate the display, please install Pivot pro 6.05 first. Then reboot PC to activate
Pivot.
2. There will be a pivot icon in the task bar. Users can click on it, and users can choose four angles: 0 degree, 90 degree, 180 degree, 270 degree to rotate the display.
3. After choosing the angle users want to rotate, there will be one blinking symbol showing as the following picture. Touch this blinking symbol until stop blinking, and the touch panel will rotate itself.
One touch blinking symbol adjustment
4. However 180 degree rotation of touch panel can not be done in one step, users need to rotate 90 degree twice.
O netouch
®
Model No.
Page
28
< Rotating display by way of RotTray icon provided by TouchKit>
1. To rotate the display, please install Pivot pro 6.05 first. Then reboot PC to activate
Pivot.
2. Users will see RotTray icon in the task bar.
RotTray
RotTray icon
3. Clicking on RotTray, it will call Pivot to rotate the display and touch panel 90 degree at the same time. Clicking it again, it will rotate another 90 degree to 180 degree. Every click on RotTray, display will rotate clockwise. Recalibration and one symbol adjustment won’t be necessary anymore.
4. However this version of RotTray is design for Pivot pro 6.05. If users want to use older version of Pivot, like Pivot 5.1, users need to amend the value of windows registry. The next step is an example for setting Pivot 5.1 on Win98.
5. Go to Start / Run, and execute regedit.
Press [OK] to execute
6. For Windows 95/98/ME OS, The Registry Editor will show as the follow picture.
Then go to
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\VxD\TKIT.
Right click on the MaxRotation, and choose Modify.
O netouch
®
Model No.
Page
29
Right click on MaxRotation to Modify Value data
7. Choosing the Hexadecimal Base, and replace the value data “4”(default) with
“FFFFFFFF”.
Pressing [OK] to confirm.
8. Here bellow are the value data for different version of Pivot:
Version of Pivot
Pivot pro 6.05
Pivot 5.1
Other Version
Available Angle
0, 90, 180, 270
0, -90
0, 90
O netouch
®
Model No.
Value Data
4 (default)
FFFFFFFF
2
Page
30
Chapter 5. Uninstalling TouchKit
Follow these steps to uninstall TouchKit.
1. Go to Start / Programs / TouchKit / Uninstall, and execute it.
2. TouchKit setup dialog appears, and prepares to uninstall.
3. Confirm dialog, press [OK] to start un-installation; [Cancel] to cancel uninstallation.
O netouch
®
Model No.
Page
31
4. Start to uninstall TouchKit.
If users do not want to uninstall TouchKit at this moment, press [Cancel] to terminate the uninstall process.
5. TouchKit will not be removed until system re-boot. Press [Yes] to re-boot immediately or [No] to re-boot later.
O netouch
®
Model No.
Page
32

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- High sensitivity and accuracy
- Multiple Interface Support (RS232, PS/2, USB)
- Mouse emulation
- Monitor rotation support
- Calibration and draw test utilities
- Sound notification options
- Multiple controller support
- Advanced mouse emulation settings