660-2130-0000-B DM2500RF-BW-English.cdr

660-2130-0000-B DM2500RF-BW-English.cdr
Your programmable dimmer DM2500RF
The installation of this dimmer should be made by a certified
electrician and must be installed in conformity with the
national and local Electrical Codes.
Press once to turn ON
the light. Hold down the
button to increase
the intensity.
Installation
guide
1
Install your dimmer
Warnings
load
This dimmer requires a neutral wire. If your electrical box
does not have a neutral wire, you can either add one or
install the dimmer at a different location.
neutral
(white)
Make sure that the
breaker for your switch
is OFF at the main
electrical panel then
remove the old switch.
line
load
CAUTION!
DM2500RF
Press once to turn OFF
the light. Hold down the
button to decrease
the intensity.
Web programmable dimmer
Maximum load per dimmer for a simple or a
multi-gang installation:
Incandescent
Lamp
Halogen
Lamp
Dimmable
LED / CFL
Single installation
600 W
600 W
150 W
Multi-gang (2 units)
500 W
500 W
150 W
Multi-gang (3 units)
400 W
400 W
150 W
Technical Specifications:
Indicator light
Light turned ON = Blue
Light turned OFF = Amber
The indicator intensity can be changed from your
neviweb® account.
Operating voltage
Operating temp.
Storage temp.
UL Standard
CSA Standard
120 Vac, 60 Hz
0 °C to 40 °C (32 °F to 104 °F)
-20 °C to 50 °C (-4 °F to 122 °F)
Conforms to ANSI/UL Std. 1472
Certified to CAN/CSA Std. C22.2#184.1
Provided connectors specifications:
16 mm
Stripping length: 16 mm
Wires: 22-10 AWG, Cu
Combinations: Max. 2 #12 & 2 #14, Min. 3 #20 Sol.
Neutral
(white)
re
d
To reduce the risk of overheating and possible damage to
another device, do not install to control an outlet, a motor or
a transformer.
ite
wh
black
e
lin
blue
Power up
the dimmer.
4
2
Use the provided connectors to connect
the wires as follows: Red
Load
Black
Line
White
Neutral
Blue
None*
*Note: For a single pole installation, do not remove
the label on the blue wire.
For a 3-way installation, consult the 3-way wiring
diagram on the next page.
3
Use the provided screws
to secure the dimmer to
the electrical box. Then,
place the wall plate.
!
Make sure to firmly tighten the wire connectors for a
secure connection. A loose connection can be a fire
hazard. Special CO/ALR solderless connectors must
be used when connecting with aluminum conductors.
Single pole wiring diagram
Connect to your network the dimmer
that is the closest to the GT125 by
pressing simultaneously the two dimmer
buttons for 1 second.
Link your dimmer to your Web Interface
Load
Electrical
Panel
1
The indicator flashes blue = Connecting
Initiate the connectivity
session by pressing the
button on the GT125.
2
(*Do not hold the button.)
DM2500RF
Wait until the green light
flashes, indicating that
new devices can be
added to your network.
white (neutral)
red (load)
black (line)
3-way wiring diagram
nevi web
FR
R
Login
Load
Electrical
Panel
E-mail address
Password
Stay connected
Sign in
Forgot your password?
New to neviweb?
Single Pole Switch
Create your account
DM2500RF
line
white (neutral)
black (line)
load
red (load)
blue (3-way)
5
If you already have a
neviweb® account, your
dimmer will automatically
be integrated to your
account.
If you do not have an
account yet, visit
neviweb.com to open an
account and add your
network. To do so, refer to
your GT125 installation
guide.
nevi web
Discover all the possibilities of your dimmers by
configuring them via www.neviweb.com
Transmitter Module IC: 7693A-89XAM9A / FCC ID:OA3MRF89XAM9A
You can connect up to 250 compatible devices to neviweb®
through one same GT125 Web interface. Visit
www.sinopetech.com to discover the full neviweb® product
range.
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
If the connectivity fails, the indicator will
turn red. Refer to our Website to
troubleshoot the unit.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between
the equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help.
After a few seconds, the indicator changes
color depending on the switch status.
(Turned ON = blue, Turned OFF = amber)
blue (3-way)
Connect your
network
to neviweb®
The indicator turns green = Connected
Stay connected at all times!
3
Connect all your dimmers
the same way, by going to
the next closest dimmer.
4
G T125
3-year limited warranty
SINOPÉ TECHNOLOGIES INC. warrants the components of their
products against defects in material and workmanship for a 3 year
period from the date of purchase, under normal use and service, when
proof of purchase of such is provided to the manufacturer. This
warranty does not cover any transportation costs that may be incurred
by the consumer. Nor does it cover a product subjected to misuse or
accidental damage. The obligation of Sinopé Technologies Inc., under
the terms of this warranty, will be to supply a new unit and this releases
the manufacturer from paying the installation costs or other secondary
charges linked to replacing the unit or the components.
3e
1er
When all dimmers are
connected, press again
on the
button of the
GT125 to close the
connectivity session.
2e
Interface Web
To be informed about our upcoming products:
nevi web
For more information, visit our Website at:
or subscribe to our newsletter.
660-2130-0000-B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement