TVLogic LVM-241W User manual


Add to my manuals
27 Pages

advertisement

TVLogic LVM-241W User manual | Manualzz

Multi

User’s Manual

Multi-Format LCD Monitors

LVM Series

LVM-171W

LVM-241W

LVM-401W

LVM-461W

LVM-571W

Contents

Warnings ........................................................................................... 2

Features ............................................................................................ 5

Name & Function of Each Part ......................................................... 6

Menu Organization & Adjustment ................................................... 11

Menu Contents ............................................................................... 12

Other Functions .............................................................................. 21

Product Specification ..................................................................... 24

Warning

·

Always use set voltage.

- AC 100 ~ 240V

- DC 12V [Only LVM-171W] / DC 24V [Only LVM-241W]

·

All operating instructions must be read and understood before the product is operated.

·

These safety and operating instructions must be kept in safe place for future reference.

·

All warnings on the product and in the instructions must be observed closely.

·

All operating instructions must be followed.

·

Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.

·

This product must be operated on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on batteries or another power source, refer to the operating instructions.

·

The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.

·

Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

·

Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.

·

Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

·

If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid is spilled on the product or when objects fall into the product.

c. When the product has been exposed to rain or water.

2

d. When the product does not operate properly as described in the operating

instructions. Do not touch the controls other than those described in the

operating instructions. Improper adjustment of controls not described in the

instructions can cause damage, which often requires extensive adjustment

work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality

in the product indicates that the product needs servicing.

·

In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

·

Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

·

When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

·

Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

·

Unplug the power cord from the AC outlet if you do not use the product for considerably long time.

·

Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

·

Keep the product away from direct rays of the Sun-light.

·

Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's instruction. Use only the mounting hardware recommended by the manufacturer.

·

When relocating the product placed on a cart, it must be moved with the utmost care.

Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.

3

·

The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed.

·

The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.

·

Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).

4

FCC (Federal Communications Commission)

This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential to correct the interference at his own expense.

Warning!!

: Change or modifications not expressly approved by the manufacturer responsible for compliance void the user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.

Features

LVM Series Monitors have the following features:

Compatible with varied SDI signals

The product is compatible with varied SDI Signals

- 480i, 576i, 720p, 1080i, 1080p, 1080psF (SDI A, B 2 channels are compatible)

Compatible with varied analog signals

The product is compatible with varied analog signals

- Composite, S-Video, Component, RGB, etc.

All-in-one system

Slim and all-in-one monitor that requires no external accessories, optimizes space utilization.

Wide Screen compatible

Wide Screen for native 16:9 aspect ratio monitoring.

AC/DC compatible

The product may be powered by normal AC source, but also 24V DC(LVM-241W) or

12V DC source(LVM-171W).

Remote control function

Remote-controlled simply with cable connection without additional peripheral equipment attached to unit.

DVI/HDMI(HDCP) function built-in

DVI/HDMI(HDCP) Input is available without any other accessory.

Dual Link support (Option)

LVM-171W (LVM-241W) can be equipped with password activated Dual Link support of

4:4:4 and 1080/60p formats.

Additional Features

Wide Viewing Angle, Loop Through (SDI), VESA Mounting Standard, 1000:1 contrast ratio

(LVM-241W), 500cd brightness, Easy to Operate User Interface and Rack-Mountable Design.

* LVM-171W contrast ratio 600:1, brightness 450cd

5

Name & Function of Each Part

<FRONT>

TALLY

ANALOG INPUT

SDI INPUT SELECT

UNDER SCAN

ASPECT

MARKER

H/V DELAY

<REAR>

6

HDMI

RS485 OUT

RS485 IN

REMOTE

AUDIO IN

AUDIO OUT

(LVM-171W / LVM-241W)

STAND BY

ENTER

UP / CONTRAST

DOWN / BRIGHT

MENU

CHROMA/PHASE

BLUE ONLY / MONO

FACTORY PGM

CVBS1/Y/G/S-Y

CVBS2/Pb/B

CVBS3/Pr/R/S-C

DVI-I

SDI IN-A

SDI OUT-A

SDI IN-B

SDI OUT-B

AC IN

<FRONT>

ANALOG INPUT

SDI INPUT SELECT

UNDER SCAN

ASPECT

MARKER

H/V DELAY

<REAR>

STAND BY

ENTER

UP / CONTRAST

DOWN / BRIGHT

MENU

CHROMA/PHASE

BLUE ONLY / MONO

RS485 OUT

RS485 IN

REMOTE

AUDIO IN

AUDIO OUT

HDMI

AC IN

SDI OUT-B

SDI IN-B

SDI OUT-A

SDI IN-A

(LVM-401W / LVM-461W / LVM-571W)

FACTORY PGM

CVBS1/Y/G/S-Y

CVBS2/Pb/B

CVBS3/Pr/R/S-C

DVI-I

7

<FRONT>

· ANALOG INPUT

Used to select an ANALOG INPUT. Sub Menu for analog input menu-selection appears.

· SDI INPUT SELECT

Used to select SDI INPUT A or B.

· UNDER SCAN

Used to toggle between OVER SCAN & UNDER SCAN modes.

(Also toggles between other Scan Modes down to: SD 1:1 SCAN mode.)

· ASPECT

Used to change the monitoring aspect ratio for anamorphic SD sources.

· MARKER

Used to toggle onscreen MARKER on/off. The type of marker at work may be selected from the main menu.

· H/V DELAY

Used to check horizontal sync and vertical sync simultaneously.

· BLUE ONLY / MONO

You may remove R(red) and G(green) from the input signal and play the screen only in B(blue) signal. Pressing the button twice will activate MONO mode. (This mode uses only luminance value.)

· CHROMA/PHASE

Used to change the CHROMIANCE and PHASE values when the OSD Menu is inactive. Pressing the button once will activate the CHROMA mode. Pressing the button twice will activate PHASE mode.

(PHASE may be used only ANALOG mode.)

· MENU

Used to activate OSD menu.

8

· DOWN/BRIGHT

Used to move within the menus during OSD menu activation. It may also be used to control the BRIGHT value when the OSD Menu is inactive.

· UP/CONTRAST

Used to move within the menus during OSD menu activation. It may also be used to control the CONTRAST value when the OSD menu is inactive.

· ENTER

Used to confirm a chosen value (or mode) or for shortcut access to volume control when OSD menu is inactive.

· STANDBY

Signifies unit is connected to power source, which is indicated by power lamp. The lamp is RED when connected to a power supply and in Standby mode. The lamp is

GREEN when monitor is on. In case of sudden power loss the last power state of the monitor is remembered.

· POWER

Used to turn power on and off.

· TALLY

LED that can be toggled via Remote Control.

<REAR>

· REMOTE (RJ-45)

Provides connection to monitor control equipment via simple GPI contact closure.

· DVI IN / FACTORY PGM

Used to connect DVI-A or DVI-D signals

- FACTORY PGM

Factory Program port used for firmware updates and automatic alignment

9

· CVBS1/Y/G/S-Y (BNC)

Signal input terminal used to feed monitor COMPOSITE 1, S-VIDEO Y, COMPONENT

Y, RGB G signals.

· CVSBS2/Pb/B (BNC)

Signal input terminal used to feed monitor COMPOSITE 2, RGB B, COMPONENT Pb signals.

· CVSBS3/Pr/R/S-C (BNC)

Signal input terminal used to feed monitor COMPOSITE 3, S-VIDEO C, COMPONENT

Pr, RGB R signals.

· SDI-IN A (BNC)

SDI/HD-SDI signal input terminal that provides A signal.

· SDI-OUT A (BNC)

SDI/HD-SDI signal output terminal used for SDI A output.

· SDI-IN B (BNC)

SDI/HD-SDI signal input terminal that provides B signal.

· SDI-OUT B (BNC)

SDI/HD-SDI signal output terminal used for SDI B output.

· Audio in & out

Built in Audio Disembedder and Internal Speakers Stereo Audio out using phone jack.

External Audio in for Stereo Speaker out

· ~ AC IN

Used to supply AC power; 100V~240V input range.

· DC 12V/24V IN

Used to supply DC power 12V(LVM-171W) or 24V(LVM-241W).

Information

Input VIDEO connection method

Connector Composite

1

2

3

CVBS1

CVBS2

CVBS3

Component

Y

Pb

Pr

G

B

R

S-Video

Y

No Con.

C

10

GGGGG

Warning!!

When using the product, make sure to connect the GND (power) first before connecting the input signal line. The unit may not operate properly if the input line is connected before the GND is connected.

Menu Organization & Adjustment

The product may be controlled and set system-wise through

OSD displayed on the screen.

1) Menu Organization

Below is the organization of the product’s menu.

2) Menu Control

You may control various functions using MENU, UP/DOWN and ENTER buttons on the bottom front of the monitor.

3) Menu Control Sequence

Menu control sequence follows the order below

1. Press MENU button to bring OSD menu on the screen.

2. Display the desired sub menu with the UP/DOWN button.

11

3. After selecting a sub menu, press ENTER to select an item with the UP/DOWN button.

4. Press ENTER to select the desired item. (Verified by highlighted field text turning red.)

5. Press ENTER to save the new value (verified by highlighted field returning to default black color.)

6. Press MENU once to remove OSD menu from the screen.

Menu Contents

Below are descriptions for each function of the menu.

[1] PICTURE menu

12

· Brightness

This item controls the degree of brightness between MAX(50) and MIN (-50) range.

· Contrast

This item controls the contrast ratio between MAX(100) and MIN(-100).

· Chroma

This item controls saturation between MAX(50) and MIN(-50).

· Phase

This item controls PHASE value (Tone) between MAX(50) and MIN(-50). However, it is only available on COMPOSITE and S-VIDEO among ANALOG modes.

· APERTURE

This item controls the picture sharpness. Sharpness selection is between MIN(-1) and

MAX(5).

· NTSC SETUP

This item sets IRE value in NTSC mode between 0 IRE and 7.5 IRE.

· SDI FORMAT

This item selects input SDI format between single link and dual link SDI.

· SDI SAMPLING

This item selects input SDI sampling mode between YCbCr and RGB for Dual Link Signals.

· FILTER

This toggles the 4:4:4 Video Processing Filter On/Off. To eliminate ringing artifacts in

4:2:2 sources please set this Filter to OFF.

· ORBITER CIRCUIT

This item is available to prevent TIR on static images displayed on screen for extended periods of time. Most scenarios do not require an orbiter circuit as TIR does not occur easily/rapidly. However, for some Multi-Viewer type applications this mode may be desirable. The orbiter value can be set between 1 and 100 (number of pixels image is scaled down). The image will move onscreen every 10 minutes.

13

· INTERNAL PATTERN

This item generates internal white pattern. The white level can be set between 0% and

100% in 5% increments.

· FAST MODE

This item minimizes deinterlacing delay and improves the quality of fast moving fine detail in interlaced sources.

· VGA H POSITION

This item controls VGA H position. It is only available in DVI analog mode.

· VGA V POSITION

This item controls VGA V position. It is only available in DVI analog mode.

· DITHERING

This item enables dithering 10 bit dithering.

· FORCE psf

This item forces psf mode for psf signals overriding automatic psf detection.

· FILM MODE DETECTION

This item toggles Film Mode On/Off

[2] COLOR menu

14

· COLOR TEMP

This item controls COLOR TEMPERATURE and allows instant access to pre-stored color temperature settings of 5000K, 5600K, 6500K, 9300K and USER modes. In user mode, the user can define custom RGB Gain and Bias Values

· GAIN RED

This item controls red color. The value is selectable between MIN(-255) and

MAX(255).

· GAIN GREEN

This item controls green color. The value is selectable between MIN(-255) and

MAX(255).

· GAIN BLUE

This item controls blue color. The value is selectable between MIN(-255) and

MAX(255).

· BIAS RED

This item adjusts black level to control red color. The value is selectable between

MIN(-50) and MAX(50).

· BIAS GREEN

This item adjusts black level to control green color. The value is selectable between

MIN(-50) and MAX(50).

· BIAS BLUE

This item adjusts black level to control blue color. The value is selectable between

MIN(-50) and MAX(50).

· COLOR COPY

This item is used to copy pre-stored color temperature settings (set and stored by automatic alignment) into a user setting as a starting point for custom color temperature setting.

15

[3] MARKER menu

· MARKER

This selects the marker type when the MARKER is displayed on the screen. MARKER may only be activated by pressing the MARKER button on the front of the monitor.

Available MARKER types are as follows:

MODE MARKER CLASS

HD

SD 16:9

SD 4:3

16:9, 4:3, 4:3 ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1

& 4:3, USER

16:9

· CENTER MARKER

This item displays the CENTER MARKER on the screen. This function operates only after activating the MARKER function by pressing the MARKER button on the front of the monitor.

· SAFETY AREA

This item controls the size of the SAFETY AREA between 80%, 88%, 90%, 93%, 100%,

EBU ACTION 16:9, EBU GRAPHIC 16:9, EBU ACTION 14:9, EBU GRAPHIC 14:9,

EBU ACTION 4:3 and EBU GRAPHIC 4:3.

· FIT MARKER

This item activates the Fit Marker Function. With Fit Marker On the Safety Area is displayed relative to the Marker in use. With Fit Marker Off the Safety Area is displayed relative to the incoming source.

16

· MARKER MAT

This item darkens the area of the outside of MARKER. The degrees of darkness are between OFF(0) and (7). The higher the number the darker the area outside of the

Marker becomes

· MARKER COLOR

This item controls the color of the MARKER lines. Available colors are white, gray, black, red, green and blue.

· MARKER THICKNESS

This item controls the width of the marker. The degrees of width are between 1 and 7.

· USER MARKER H1 / H2

This item controls the position of up to two user defined Horizontal Marker lines.

· USER MARKER V1 / V2

This item controls the position of up to two user defined Vertical Marker lines.

[4] REMOTE menu

This product provides a REMOTE CONTROL mode. The user may connect an

RJ-45 jack to the REMOTE terminal on the rear of the unit and designate a function for each pin.

The user designates function for PIN 1~PIN 6. PIN 7 is POWER ON/OFF use only, PIN

8 is the GND. The selectable functions are as follows:

17

Menu

Classification

PIN 1~6

Settable Values

NONE, ANALOG CHANNEL, DIGITAL A/B CHANNEL, BLUE

ONLY, SD 1:1 SCAN, UNDER SCAN, ASPECT, H/V DELAY,

16:9,15:9,14:9,13:9 MARKER, 4:3, 4:3 ON AIR MARKER,

1.85:1, 2.35:1 MARKER, 1.85:1&4:3 MARKER, CENTER

MARKER,SAFETY AREA 80% / 88% / 90% / 93%, TALLY RED,

TALLY GREEN

On the pin to be used, set the function you desire with the ENTER button and

UP/DOWN button. The method of setting the value is the same as that for the MENU function discussed earlier.

[5] SYSTEM menu

· SET DEFAULT

You can use the SET DEFAULT menu to reinitialize the values of BRIGHT, CONTRAST,

PHASE and CHROMA of the monitor.

18

· USER CONFIG SET

This item saves three different user configurations, which can be recalled by simply selecting User 1, 2, or 3.

· BACK LIGHT

This item controls the LCD Panel’s backlight brightness. The value is selectable between MIN(0) and MAX(50).

· AUDIO VOLUME

This item controls audio volume between MIN (0) and MAX (30).

· AUDIO CHANNEL

This item selects the single or stereo pair of embedded audio channels to monitor.

This item can be set to CH1~16 or Off.

· LOCK NUMBER

Lock number is product’s serial number.

· LOCK ENABLE

Lock enable is the area reserved for the Dual Link Enable Key, which can be purchased separately, to password activate the Dual Link Option.

· BOARD VER

This item represents the serial number and hardware configuration of the monitor

(Board Version can only be altered via firmware update.)

· KEY LED

This item toggles the monitor’s front panel LED lights On/Off.

· OSD DISPLAY

This item controls OSD DISPLAY time. (20 sec or continuous)

· OSD POSITION

This item controls OSD Menu position. (Left-Top, Left-Bottom, Right-Top, Right-Bottom and Center.)

19

· SOURCE ID

This item toggles between Source ID modes. (MANUAL, ANC, Off)

· SOURCE ID CHARACTER

This item is used to set the 5 character source ID displayed when Source ID function is set to Manual. (Use Menu, Down, Up and Enter key to adjust Source ID characters.)

· SOURCE ID POSITION

This item controls Source ID position. (Left-Top, Left-Bottom, Center-Top, Center-

Bottom, Right-Top and Right-Bottom)

· CLOSED CAPTION

This item toggles between available CC modes (608 line 21, 608 ANC data, 708, & Off)

· AUDIO LEVEL METER

This item controls on screen audio level meter display.

· AUDIO LEVEL METER

This item sets embedded audio groups to monitor, selection are: off, G1+G2,

G2+G3, G3+G4, G1+G3, G1+G4,G2+G4.

· AUDIO LEVEL METER DISPLAY

When audio level meter is activated, This item controls display method.(Pair, Group)

· AUDIO LEVEL METER REFERENCE

This item sets audio level default.(-18dB, -20dB) Changes point where audio level meter switches from Green to Yellow.

· WAVEFORM/VECTOR

This item toggles between waveform and vector scope.

When in waveform mode it displays the shape and form of the luminance level of a signal. When in Vector scope mode it displays an X-Y plot of color signal.

· WAVEFORM TYPE

This item displays the waveform type (not a user adjustable mode).

20

· WAVEFORM POSITION

This item sets the waveform position.(R-B,C-B,L-B,L-T,C-T,R-T)

· WAVEFORM SIZE

This item sets the waveform size.( Large,Medium,Small)

· TIME CODE ENABLE

This item displays the time code. (VITC, LTC)

Other Functions

[1] ANALOG Mode Usage

This product is capable of processing numerous input signals in ANALOG mode.

The ANALOG input settings are as follows:

1. Press ANALOG button on the front of the product and activate the menu below.

2. Highlight the value you desire by using the UP/DOWN button and press the MENU button to confirm your selection. From this point the OSD menu operates identically to the MENU operations discussed above.

Warning!!

When using ANALOG mode, always check the input method and modify the setting as needed for optimized output results.

21

[2] SD 1:1 SCAN Mode

Widescreen models provide not only an UNDERSCAN mode but also an SD 1:1

SCAN mode. These modes may be selected as follows:

1. Transfer to UNDERSCAN by pressing the UNDERSCAN button on the front of the monitor.

2. Press the UNDERSCAN button again after the mode is shifted to UNDERSCAN mode to transfer to SD 1:1 SCAN mode.

[3] DVI Support Resolution

DVI-ANA mode supports the following modes:

Resolution Frequency

640 × 480 60Hz, 75Hz

800 × 600

1024 × 768

720 X 400

60Hz, 72Hz, 75Hz

60Hz, 70Hz, 75Hz

70Hz

DVI-DIG mode is separated into Graphic mode and Video mode. Graphic mode supports the below resolutions and frequencies. DVI-DIG Graphic mode supports the following modes:

Resolution Frequency

640 × 480 60Hz, 75Hz

800 × 600 60Hz, 72Hz, 75Hz

1024 × 768

1280 × 1024

1600 X 1200

1920 X 1200

60Hz, 70Hz, 75Hz

60Hz

60Hz

60Hz

22

DVI-DIG Video mode supports the following input signals.

SMPTE-274M

SMPTE-296M

1080i (60 / 59.94)

720p (60 / 59.94)

୔GWhen using DVI function, User must select Underscan button.

୔G If not using a native widescreen mode the image can be viewed in widescreen aspect by pressing the aspect button.

[4] DUAL LINK Mode

This product provides a DUAL LINK mode. If user wants to view dual link signal, select signal format on picture menu. DUAL LINK Mode can be setup by following these steps:

1. Press the MENU button to bring up the OSD menu.

2. Display Picture menu and press ENTER button and then the PICTURE menu will be activated.

3. Select DUAL option in SDI FORMAT.

4. Select YCbCr 444, YCbCr 422 or RGB option in SDI SAMPLING.

23

Product Specification

Below is the product specification

LVM-171W LVM-241W

Input

Output

Input Signal

Analog Input Spec

1 x DVI-I

3 x BNC

2 x BNC

1 x HDMI

3 x BNC

2 x BNC

Analog

HD-SDI

SD-SDI

DVI

HDMI

Composite

S-Video

Component

RGB

DVI-I(RGB) IN

Analog Input

SDI A/B Channel Input

HDMI Input

Analog Output

SDI A/B Channel (Active Through Out)

Composite / S-Video / Component / RGB

1.458Gpbs

270Mpbs

VESA/IBM Modes

480i/480p/720p/1080i & VESA/IBM Modes

1.0Vpp (With Sync)

1.0Vpp (Y With Sync), 0.286Vpp(C)

1.0Vpp (Y With Sync), 0.7Vpp (Pb,Pr)

SDI Input Signal Formats SMPTE-296M

SMPTE-260M

SMPTE-125M

ITU-R BT.656

Audio In

Audio Out

Size

Resolution

Pixel Pitch

LCD

Color

Viewing Angle

Luminance of white

Contrast

Power

Power Consumption (Approx.)

Display Area

Operating Temperature

Storage Temperature

Main Body Dimensions (mm/inch)

Main Body Dimensions (With Stand)

Weight

Accessory

Option

SMPTE-274M

1.0Vpp (G With Sync), 0.7Vpp (B,R)

1080i (60/59.94/50)

1080p (30/29.97/25/24/24sF/23.98/23.98sF)

720p (60/59.94/50)

Embedded Audio / Analog Stereo (Phone Jack)

17.1”

1280 x 768 (15:9)

0.291(H) x 0.291(W) mm

16.7M(true 8bit)

H : 176 degrees / V : 176 degrees

450 cd/

༇ (Center)

600:1

1035i (60/59.94)

480i (59.94)

AC / DC Power cord

Carrying Case, V-Mount, Hood/Handle

19” Rack Mountable Kit,

Dual-Link, ND Filter

576i (50)

Analog Stereo (Phone Jack)

372.4(H) x 223.4(V) mm

DC 12V(5A)/AC100~240V(1.8A/50~60Hz)

60 Watts(DC / Max.)

0 ୅ to 40୅ (32එ to 104එ)

-20 ୅ to 60୅ (-4එ to 140එ)

406 x 310 x 82 (15.98 x 12.20 x 3.22)

440 x 333 x 120 (17.32 x 13.11 x 4.72)

8Kg / 17.6 lb

24”

1920 x 1200 (16:10)

0.270(H) x 0.270(W) mm

16.7M(true 8bit)

H : 178 degrees / V : 178 degrees

500 cd/

༇ (Center)

1000:1

518.4(H) x 324.0(V) mm

DC 24V(6A)/AC100~240V(1.8A/50~60Hz)

0

-20

73 Watts(DC / Typ.)

୅ to 35୅ (32එ to 95එ)

୅ to 60୅ (-4එ to 140එ)

552 x 389 x 95 (21.73 x 15.31 x 3.74)

586 x 417 x 150 (23.07 x 16.41 x 5.90)

11Kg / 24.2 lb

AC / DC Power cord

Carrying Case

19” Rack Mountable Kit

Dual-Link, ND Filter

* Above specifications may be changed without notice

24

Product Specification

Below is the product specification

LVM-401W LVM-461W LVM-571W

Input

Output

Input

Signal

Analog

Input Spec

1 x DVI-I

1 x HDMI

3 x BNC

2 x BNC

1 x BNC

3 x BNC

2 x BNC

1 x BNC

Analog

HD-SDI

SD-SDI

HDMI

DVI-Analog

DVI-Digital (Graphic)

DVI-Digital (Video)

Composite

S-Video

Component

RGB

DVI IN

HDMI IN

Analog Input

SDI 2 Channel Input

-

Analog Out

SDI 2 Channel Output

-

Composite / S-Video / Component / RGB

1.485Gbps

270Mbps

1080p / 1080i / 720p / 480i

640×480 / 800×600 / 1024×768 / 1280×768 / 1280×1024 / 720×400

640×480 / 800×600 / 1024×768 / 1280×768 / 1280×1024 / 720×400 / 1600×1200 / 1920×1200 / 1920×1080

1080p (60/59.94/50) / 1080i (60/59.94/50) / 720p (60/59.94/50) / 480i (59.94) /480p (59.94) / 576i (50)

1.0Vpp (With Sync)

1.0Vpp (Y With Sync), 0.286 Vpp (C)

1.0Vpp (Y With Sync), 0.286 Vpp (Pb,Pr)

1.0Vpp (G With Sync), 0.286 Vpp (B,R)

SMPTE-274M

SMPTE-296M

1080i (60 / 59.94 / 50)

1080p (30 / 29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF)

720p (60 / 59.94 / 50)

Dual HD-SDI YPbPr (4:2:2) 1080p (50 / 59.94 / 60)

SDI Input

Signal

Formats

SMPTE-372M**

SMPTE-260M

SMPTE-125M

ITU-R BT.656

2K Format

1080i (29.97 / 25 / 24 / 23.98)

Dual HD-SDI YPbPr/RGB (4:4:4) 1080p (30 / 29.97 / 25 / 24 / 23.98)

720p (60 / 59.94 / 50)

1035i (60 / 59.94)

480i (59.94)

576i (50)

2048 X 1080 ( 23.98psf / 24psf / 23.98p / 24p )

Embedded Audio / Analog stereo (Phone Jack)

Audio IN

Audio OUT

Size

Resolution

40"

1920×1080 (16:9)

0.461 mm

LCD

Dot Pitch

Color

Viewing Angle

(Typical)

Luminance of White

16.7M (True), 24bit

H : 178 degree

V : 178 degree

450 cd (Center)

Contrast

Display Area

Power

Power Consumption (Approx.)

Operating Temperature

Storage Temperature

Main Body Dimensions (mm/inch)

Main Body Dimensions (with stand)

Weight

Accessory

Option

1000 : 1

885.60×498.15 mm

AC 100 - 240 V (1.8A/50~60Hz)

290 Watts

0 °C to 40 °C ( 32 °F to 104 °F )

-20 °C to 60 °C (-4 °F to 140 °F)

990.6×589.6×111.8(39.0×23.2×4.4)

990.6×642.7×255(39.0×25.3×10.0)

35Kg / 77.2 lb

AC Power Cord

Carrying Case / WALL mount

Dual-Link / ND Filter

Analog stereo (Phone Jack)

46"

1920×1080 (16:9)

0.53 mm

16.7M (True), 24bit

H : 178 degree

V : 178 degree

450 cd (Center)

1000 : 1

1018×572 mm

AC 100 - 240 V (1.8A/50~60Hz)

349 Watts

0 °C to 40 °C ( 32 °F to 104 °F )

-20 °C to 60 °C (-4 °F to 140 °F)

1126.6×670.7×103.8(44.4×26.4×4.1)

1126.6×723.8×255(44.4×28.5×10)

42Kg / 92.6 lb

AC Power Cord

Carrying Case / WALL mount

Dual-Link / ND Filter

57"

1920×1080 (16:9)

0.651 mm

16.7M (True), 24bit

H : 178 degree

V : 178 degree

600 cd (Center)

1200 : 1

1251.36×703.89 mm

AC 100 - 240 V (1.8A/50~60Hz)

516 Watts

0 °C to 40 °C ( 32 °F to 104 °F )

-20 °C to 60 °C (-4 °F to 140 °F)

1370×807×120(54.0×31.8×4.7)

1370×857.7×350(54.0×33.8×13.8)

57Kg / 125.66 lb

AC Power Cord

Carrying Case / WALL mount

Dual-Link / ND Filter

* Above specifications may be changed without notice

25

Multi

HDMI

TVLogic Product Line

LVM - 071W LVM - 171W LVM - 241W

LVM - 401W LVM - 461W LVM - 571W

LHM - 400W LHM - 460W LHM - 570W

Developed by

For more information please visit : www.tvlogic.co.kr

Suite 914 ACE TECHNO TOWER-9, 345-30 Gasan-Dong, GuemChun-Gu, Seoul, Korea

TEL : +82-2-2026-1333 FAX : +82-2-2026-1339 E-mail : [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement