16467200US Service Manual - English
OWNER`S
MANUAL
Model No.
16467200US
Xterra
Upright Cycle
CAUTION:
You must read and
understand this
owner’s manual
before operating unit.
Keep this manual for
future reference.
UPRIGHT CYCLE
TABLE OF CONTENTS
Manufacturer’s Limited Warranty ……………………. …… 2
Safety Precautions………….………………………………. 3
Before you begin …………………………………………….. 4
Pre-assembly Check List…………………………………… 5
Hardware Packing List……………………………………… 6
Assemble Instruction……………………………………….. 7-9
Monitor Instruction……...…………………………………… 10-16
User Direction……………………………………………….. 17-18
Maintenance Parts………………………………………….. 19-20
Parts List / Diagram ………………………………………… 21-23
Trouble Shooting …………………………………………….. 24
Training Guideline …………………………………………… 25-27
Stretching …………………………………………………….. 28-29
Customer Service 1-888-707-1880
or email [email protected]
1
Dyaco Canada Inc. ©2014
Manufacture’s One-Year Limited Warranty
Your Xterra Cycle is warranted for one year from the date of purchase against defects in
material when used for the purpose intended, under normal conditions and provided it
receives proper care. Any part found defective or missing will be sent at no cost when
returned in accordance with the terms of this warranty.
This warranty is not transferable and is extended only to the original owner.
The warranty shall not apply to exercise units which are (1) used for commercial or other
income producing purposes, or (2) subject to misuse, neglect, accident or unauthorized
repair and alterations.
This warranty provided herein is lieu of all other express warranties, any implied warranties,
including any implied warranties of merchantability of fitness for particular purpose, are
limited in duration to the first 12 months from date of purchase. All other obligations or
liabilities, including liability for consequential damages are hereby excluded.
REPAIR PARTS AND SERVICE
All of the parts for the cycle shown in figure can be ordered from Dyaco Canada Inc.
6050 DON MURIE STREET, NIAGARA FALLS, ONTARIO L2G 0B3. When ordering parts,
the parts will be sent and billed at the current prices. Prices may be subject to change without
notice. Check or money order must accompany all orders. Standard hardware items are
available at your local hardware store.
To ensure prompt and correct handling of any errors, or to answer any questions, please call
our Toll Free number: 1-888-707-1880, or local number 1-905-353-8955 or fax 1-905-3538968 or email [email protected] or visit us at: www.dyaco.ca Office hours are from
8:30 AM to 5:00 PM Monday to Friday Eastern Standard Time.
Always include the following information when ordering parts
 Model number
 Name of each part
 Part number of each part
Customer Service 1-888-707-1880
or email [email protected]
2
Dyaco Canada Inc. ©2014
SAFETY PRECAUTIONS
Thank you for purchasing our product. Even though we go to great efforts to ensure the quality of each
product we produce, occasional errors and /or omissions do occur. In any event should you find this
product to have either a defective or a missing part please contact us for a replacement.
This product has been designed for home use only. Product liability and guarantee conditions will not be
applicable to products being subjected to professional use or products being used in a gym center.
This exercise equipment was designed and built for optimum safety. However, certain
precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before assembly and operation of this machine. Also, please note the following safety precautions:
1. Read the OWNER’S OPERATING MANUAL and all warnings posted on the exercise cycle and follow it
carefully before using your cycle.
2. If dizziness, nausea, chest pains, or any other abnormal symptoms are experienced while using this
equipment, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
3. Review all warnings labels that affixed to the cycle. Inspect your exercise equipment prior to exercising
to ensure that all nuts and bolts are fully tightened before each use. Functional and visual inspection of the
equipment shall be made after assembling your cycle
4. The cycle must be regularly checked for signs of wear and damage. Any part found defective must be
replaced with a new part from the manufacturer.
5. Set up and operate the exercise bicycle on a solid level surface. It is recommended to use an equipment
mat to prevent the unit from moving while it is being used, which could possibly scratch or damage the
surface of your floor.
6. No changes must be made which might compromise the safety of the equipment.
7. It is recommended to have a minimum of 2’ safe clearance around the exercise equipment while in use.
8. The pulse sensor is not a medical devise. Various factors, including the user’s movement may affect
the accuracy of the heart rate readings. The pulse sensor is intended only as an exercise aid in
determining heart rate trends in general
9. Keep children and pets away from this equipment at all times while exercising.
10. Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This allows
your heart rate to gradually increase and decrease and will help prevent you from straining muscles.
11. Never hold your breath while exercising. Breathing should remain at a normal rate in
conjunction with the level of exercise being performed
12. Always wear suitable clothing and footwear while exercising. Do not wear loose fitting clothing that
could become entangled with the moving parts of your cycle.
13. Always hold the handlebars when mounting, dismounting or using the cycle. When you stop exercising,
allow pedals to slowly come to a complete stop before dismounting.
14. Care must be taken when lifting or moving the equipment, so as not to injure your back. Always use
proper lifting techniques.
15. User weight should not exceed 265lbs.
16. Tie all long hair back.
17. Remove all personal jewellery before exercising.
18. After eating, allow 1-2 hours before exercising as this will help to prevent muscle strain.
19. Injuries may result from incorrect or excessive training and using the equipment otherwise than as
directed or recommended by your doctor.
20. The decal shown below has been placed on the exercise cycle. If the decal is missing, or if it is not
legible, please call the toll-free telephone number on the front cover of this manual and order a free
replacement decal. Apply the decal in the location shown.
21. The exercise cycle does not free-wheel. Spinning pedals can cause injury. Pedal speed should be
reduced in a controller manner.
WARNING: Before beginning any exercise program consult your physician. This is especially
important for individuals over the age of 35 or persons with pre-existing health problems. Read all
instructions before using any fitness equipment. We assume no responsibility from personal
injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
Customer Service 1-888-707-1880
or email [email protected]
3
Dyaco Canada Inc. ©2014
BEFORE YOU BEGIN
Thank you for selecting the revolutionary Xterra exercise bike. Cycling is an effective exercise
for increasing cardiovascular fitness, building endurance, and toning the body. The exercise
bike provides an impressive selection of features designed to make your workouts at home
more effective and enjoyable.
For your benefit, read this manual carefully before you use the exercise bike. If you
have questions after reading this manual, please see the front cover of this manual. To help
us assist you, note the product model number and serial number before contacting us. The
model number and the location of the serial number decal are shown on the front cover of
this manual. Before reading further, please familiarize yourself with the parts that are labeled
in the drawing below
Monitor
Hand pulse sensor
Handlebar
Seat
Upright
Seat post
Right pedal
w/strap
Quick release knob
Transport wheel
Adjustable End Cap
·
Left pedal
w/ strap
Customer Service 1-888-707-1880
or email [email protected]
4
Dyaco Canada Inc. ©2014
PRE-ASSEMBLY CHECK LIST
NO:1
NO:4
NO:2
NO:8
PART NO.
1
2
3
4
5
6/77
7
8
9
10
17
36
75
NO:3
NO:9
NO:5
NO:10
NO:17
DESCRIPTION
Main frame
Front stabilizer
Rear stabilizer
Upright
Handlebar
Computer / Audio wire
Seat post
Seat
Left pedal
Right pedal
Cover for seat post
Towel rack
Bottle holder
Hardware bag
Manual
Customer Service 1-888-707-1880
or email [email protected]
NO:7
NO:6/77
NO:36
NO:75
Q’TY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
Dyaco Canada Inc. ©2014
HARDWARE PACKING LIST
Part No
Description
Q’ty
11
Quick release knob
1
13
Spring washer Φ8*Φ17
4
15
Allen screw M8*75
4
16
Curved washer Φ8*Φ20
8
18
Allen screw M8*16
4
21
T-type knob
1
37
Cover for clamp
1
78
Box wrench
1
79
Allen key 6mm
1
Drawings
Note: Above parts are all the parts needed to assemble this machine. Before you start
to assemble, please check the hardware packing to make sure they are included.
Customer Service 1-888-707-1880
or email [email protected]
6
Dyaco Canada Inc. ©2014
ASSEMBLY INSTRUCTION
This manual is designed to help you easily assemble, adjust and use this machine. Please read this
manual carefully. For the sake of familiarizing yourself with the parts identified in the instruction, first
study the overview drawing.
Set all parts in a clear area on the floor and remove the packing material. Refer to the parts list for
help to identify the parts.
It will take two people to assemble your unit.
Note: If a part is not in the hardware kit, check to see if it has been preassembled. To avoid
damaging parts, do not use power tools for assembly
STEP 1
 Attach the front stabilizer (2) to the main frame (1), securing with two sets of allen screw (15),
spring washer (13) and curved washer (16).
 Attach the rear stabilizer (3) to the main frame (1), securing with two sets of allen screw (15),
spring washer (13) and curved washer (16).
15 13
16
1
3
2
16
13
15
STEP 2
 Connect the computer extension wire (33) to the lower computer wire (34). Insert the upright (4)
to the main frame (1). Secure using four curved washers (16) and four allen screws (18).
 Tip: Avoid pinching the Extension Wire
33
4
34
33
18
34
16
16
18
1
Customer Service 1-888-707-1880
or email [email protected]
7
Dyaco Canada Inc. ©2014
STEP 3





Remove the clamp (25) and allen screw (22) from the upright (4). Attach the handlebar (5) to the
front of the upright (4) using the clamp (25). Finger tighten the allen screw (22) to the top of the
clamp (25). Attach the plastic cover (37) over the clamp using the t-type knob (21).
Connect the extension wire (33) to the wire from the back of the monitor (6).
Connect the handpulse wires (20) to the wires from the back of the monitor (6).
Attach the monitor to the bracket of the upright (4). Secure using the four screws (27) which are
pre-assembled on the back of the monitor
Tip: Avoid pinching the Extension Wire
6
27
27
20
21
33
4
32
5
25 22
37
STEP 4




Orient the seat (8) and the seat post (7) as shown.
Attach towel rack (36) to the sliding tube under the seat (8). Secure using the two flat washers
(12), two spring washers (13) and two nylon nut (14) which are pre-assembled on the seat.
Slide the seat (8) on to sliding tube of the seat post (7) and secure with one carriage bolt (47),
one square plate (48), one small bushing (49) and the seat adjustment knob (19).
Insert the seat post (7) into main frame (1) through the cover for seat post (17). Tighten with quick
release knob.
8
12
13
14
47
48
49
19
36
7
17
11
1
Customer Service 1-888-707-1880
or email [email protected]
8
Dyaco Canada Inc. ©2014
STEP 5


The left and right pedals (9 & 10) are marked “L” & “R”. Attach the straps to the pedals. Connect
left pedal (9) to the crank (38) on the left hand side of the cycle as you sit on it. Repeat for the
right pedal (10).
Note that the right pedal should be threaded on clockwise and the left pedal on counterclockwise.
Attach the bottle holder (75) to the upright (4) and tighten with 2 screws (45) which are preassembled on the upright.
75
4
45
10
1
9
38
STEP 6


To listen to an MP3 during your workout, connect the MP3 with the computer (6) by using the
audio wire (77)
Plug adapter (76) into the power receptacle (61).
6
77
1
NOW FIRMLY TIGHTEN ALL NUTS AND BOLTS
YOUR UNIT IS NOW FULLY ASSEMBLED
Your cycle is equipped with adjustable end caps.
If the unit is wobbly, please turn the leveling caps. See page 18
Customer Service 1-888-707-1880
or email [email protected]
9
Dyaco Canada Inc. ©2014
MONITOR INSTRUCTIONS
FUNCTION BUTTON
START/STOP:
Press to start or stop your exercise program.
Press to start body fat measurement.
Press and hold for three seconds to reset all values to zero.
UP:
Press UP to increase the target values.
Press UP to increase the tension level while you are exercising.
Press UP to select your desired program.
DOWN:
Press DOWN to decrease the preset target values.
Press DOWN to decrease the tension level.
Press DOWN to select your desired program.
ENTER:
Press to accept the desired program.
Press to accept the target value.
Press and hold for four seconds to reset all values to zero.
Body Fat:
Press to have your body fat measurement.
Pulse RECOVERY:
Press to have the recovery grade of F1 to F6
FUNCTION:
Time:
Shows your elapsed workout time up to 99:59.
Counts down from your preset target time to 0:00 during your workout.
Speed:
Displays between the current speed up to 99.9 M/H.
Distance: Displays the cumulative distance traveled during your workout up to
99.99 M.
Counts down from your preset target time to 0 M during your workout.
RPM:
Displays the current rotation per minute.
Customer Service 1-888-707-1880
or email [email protected]
10
Dyaco Canada Inc. ©2014
Calories:
Displays between the cumulative calories burned at any given time during your
workout up to 999.
Counts down from your preset target calorie to 0
Note: This is a rough guide used for comparison of different exercise sessions,
which cannot be used for medical purposes.
Watt:
When pre-setting the watt, the tension will adjust according to the speed and
the watt value you set.
Body fat:
Hand on the pulse grip, press the body fat key, the monitor will be measure the
data of fat% , bmi, bmr.
Gripped pulse
Display’s the user’s current heart rate in beats per minute during the workout.
Both hands must hold the gripped pulse for a heart rate reading during your
workout.
You may preset your target pulse. The computer will alarm to remind you
as soon as your current heart rate has achieved at the preset figure.
Note: This data is a rough guide used for comparison of different exercise
sessions, which cannot be used for medical purposes.
Pulse Recovery:
Your computer is equipped with a recovery program to monitor your heart rate
recovery. After your workout, press the recovery button and keep both hands
on the gripped pulse. The computer will cease monitoring all functions except
time which will commence countdown from 00:60 to 00:00.
Once zero is reached the pulse function will display a grade between F1 to F6.
F1 being the best and F6 being the worst reading you can receive.
Press the recovery button to return to the main display.
Note: If no pulse signal input then the computer will show “P” on the PULSE
window. If the computer shows “ERR” on the message window, please re-press
the PULSE RECOVERY key and please make sure your hands are keeping
well on the grips or the chest transmitter is attached well.
DISTANCE BAR
Every bar indicates 0.1 mile.
SPEAKER:
To listen to an MP3 during your workout, connect the MP3 to the monitor (6) by
using the audio wire (77). Volume is controlled by the MP3 player.
PROGRAM:
Displays the program level from P1 to P23
P1 –Manual you can control the tension level
P2 to P13 programs are preset at the factory.
P14 to P17 programs are user setting
P18 to P22 programs are heart rate control programs
P23 body fat program
Remarks
1.
The monitor will turn on automatically by pressing any key or when
your start to pedal. The monitor will shut off automatically if no signal
is detected for four minutes and will keep all function values. You may
press Start button or start to pedal to have the computer resume.
2.
Press the enter button for four seconds to reset all values to zero
Customer Service 1-888-707-1880
or email [email protected]
11
Dyaco Canada Inc. ©2014
Program Introduction & Operation:
Manual Program: Manual
P1 is a manual program. User can start exercise by pressing START/STOP key. The default
resistance level is 5. Users may exercise in any desirous of resistance level (Adjusting by
UP/DOWN keys during the workout) with a period of time or a number of calories or a certain
distance.
Operations:
1. Use UP/DOWN keys to select the MANUAL (P1) program.
2. Press the ENTER key to enter MANUAL program.
3. The TIME will flash and you can press UP or DOWN keys to set your exercise TIME.
Press ENTER key to confirm your desired TIME.
4. The DISTANCE will flash and you can press UP or DOWN keys to set your target
DISTANCE. Press ENTER key to confirm your desired DISTANCE.
5. The CALORIES will flash and you can press UP or DOWN keys to set your exercise
CALORIES. Press ENTER key to confirm your desired CALORIES.
6. The PULSE will flash and then you can press UP or DOWN keys to set your exercise
PULSE. Press ENTER key to confirm your desired Pulse.
7. Press the START/STOP key to begin exercise.
Preset Program:
Steps, Hill, Rolling, Valley, Fat Burn, Ramp, Mountain, Intervals, Random, Plateau, Fartlek,
Precipice Program
PROGRAM 2 to PROGRAM 13 is the preset programs. Users can exercise with different
level of loading in different intervals as the profiles show. Users may exercise in any desirous
of resistance level (Adjusting by UP/DOWN keys during the workout) with a period of time or
a number of calories or a certain distance.
Operations:
1. Use UP/DOWN keys to select one of the above programs from P2 to P13.
2. Press the ENTER key to enter your workout program.
3. The TIME will flash and you can press UP or DOWN keys to setting your exercise TIME.
Press ENTER key to confirm your desired TIME.
4. The DISTANCE will flash and you can press UP or DOWN keys to setting your target
DISTANCE. Press ENTER key to confirm your desired DISTANCE.
5. The CALORIES will flash and you can press UP or DOWN keys to setting your exercise
CALORIES. Press ENTER key to confirm your desired CALORIES.
6. The PULSE will flash and then you can press UP or DOWN keys to set your exercise
PULSE. Press ENTER key to confirm your desired Pulse.
7. Press the START/STOP key to begin exercise.
Customer Service 1-888-707-1880
or email [email protected]
12
Dyaco Canada Inc. ©2014
User Setting Program: User 1, User 2, User 3, User 4
Program 14 to 17 is the user setting program. Users are free to create the values in the order
of TIME, DISTANCE, CALORIES and the resistance level in 10 columns. The values and
profiles will be stored in the memory after setup. Users may also change the ongoing loading
in each column by UP/DOWN keys, and they will not change the resistance level stored in
the memory.
Operations:
1. Use UP/DOWN keys to select the USER program from P14 to P17.
2. Press the ENTER key to enter your workout program.
3. The column 1 will flash, and then use the UP/DOWN keys to create your personal
exercise profile. Press ENTER to confirm your first column of exercise profile. The default
level is load 1.
4. The column 2 will flash, and then use the UP/DOWN keys to create your personal
exercise profile. Press ENTER to confirm your second column of exercise profile.
5. Follow the above description 5 and 6 to finish your personal exercise profiles. Press
ENTER to confirm your desired exercise profile.
6. The TIME will flash and you can press UP or DOWN keys to setting your exercise TIME.
7. Press ENTER key to confirm your desired TIME.
8. The DISTANCE will flash and you can press UP or DOWN keys to setting your target
DISTANCE. Press ENTER key to confirm your desired DISTANCE.
9. The CALORIES will flash and you can press UP or DOWN keys to setting your exercise
CALORIES. Press ENTER key to confirm your desired CALORIES.
10. The PULSE will flash and then you can press UP or DOWN keys to set your exercise
PULSE. Press ENTER key to confirm your desired Pulse.
11. Press the START/STOP key to begin exercise.
Heart Rate Control Program:
55% H.R.C., 65% H.R.C., 75% H.R.C., 85% H.R.C., Target H.R.C.
Program 18 to Program 22 is the Heart Rate Control Programs and Program 22 is the Target
Heart Rate Control program.
Program 18 is the 55% Max H.R.C. - - Target H.R. = (220 – AGE) x 55%
Program 19 is the 65% Max H.R.C. - - Target H.R. = (220 – AGE) x 65%
Program 20 is the 75% Max H.R.C. - - Target H.R. = (220 – AGE) x 75%
Program 21 is the 85% Max H.R.C. - - Target H.R. = (220 – AGE) x 85%
Program 22 is the Target H.R.C. - - Workout by your target heart rate value.
Users can exercise according to your desired Heart Rate program by setting your AGE,
TIME, DISTANCE, CALORIES or TARGET PULSE. In these programs, the computer will
adjust the resistance level according to the heart rate detected. For example, the resistance
level may increase every 20 seconds while the heart rate detected is lower than the TARGET
H.R.C. Also the resistance level may decrease every 20 seconds while the heart rate
detected is higher than the TARGET H.R.C.
Customer Service 1-888-707-1880
or email [email protected]
13
Dyaco Canada Inc. ©2014
Operations:
1. Use UP/DOWN keys to select one of the heart rate control program from P18 to P22.
2. Press the ENTER key to enter your workout program
3. The AGE will flash at P18 to P21 programs and you can press UP or DOWN keys to set
your AGE. The default age is 35.
4. At program 22, the TARGET PULSE will flash and you can press UP or DOWN keys to
set your TARGET PULSE between 80 to 180. The default TARGET PULSE is 120.
5. The TIME will flash and you can press UP or DOWN keys to set your exercise TIME.
Press ENTER key to confirm your desired TIME.
6. The DISTANCE will flash and you can press UP or DOWN keys to set your target
DISTANCE. Press ENTER key to confirm your desired DISTANCE.
7. The CALORIES will flash and you can press UP or DOWN keys to set your exercise
CALORIES. Press ENTER key to confirm your desired CALORIES.
8. Press the START/STOP key to begin exercise.
Body Fat Program: Body Fat
Program 23 is a special program design to calculate users’ body fat ratio and to offer a
specific loading profile for users. There are 3 body types divided according to the FAT%
calculated.
Type1: BODY FAT% > 27
Type2: 27 ≧ BODY FAT% ≧ 20
Type3: BODY FAT % < 20
The computer will show the test results of FAT PERCENT
Operations:
1. Use UP/DOWN keys to select the BODY FAT (P23) program.
2. Press the ENTER key to enter your workout program.
3. The HEIGHT will flash and you can press UP or DOWN keys to set your HEIGHT. Press
ENTER key to confirm your HEIGHT. The default HEIGHT is 170cm or 5’07” (5feet 7
inches).
4. The WEIGHT will flash and you can press UP or DOWN keys to set your WEIGHT. Press
ENTER key to confirm your WEIGHT. The default WEIGHT is 70kgs or 155lbs.
5. The GENDER will flash and you can press UP or DOWN keys to select your sex. Number
1 means man and number 0 means female. Press ENTER key to confirm your Gender.
The default sex is 1 (MAN).
6. The AGE will flash and you can press UP or DOWN keys to set your AGE. Press ENTER
key to confirm your AGE. The default AGE is 35.
7. Press the START/STOP key to begin body fat measurement. If the window show E on the
window, please make sure your hands are attached well on the grips or the chest belt is
touch well on your body. Then press the START/STOP key again to begin body fat
measurement.
8. After finished your measurement, the computer will show the values of FAT PERCENT on
the LCD display.
9. Press START/STOP key to begin exercise.
Customer Service 1-888-707-1880
or email [email protected]
14
Dyaco Canada Inc. ©2014
PRESET PROGRAM PROFILES:
PROGRAM 1
PROGRAM 2
MANUAL
STEPS
PROGRAM 3
HILL
PROGRAM 5
VALLEY
PROGRAM 6
FAT BURN
PROGRAM 7
RAMP
PROGRAM 8
MOUNTAIN
PROGRAM 9
INTERVAL
PROGRAM 10
SRANDOM
PROGRAM 11
PLATEAU
PROGRAM 12
FARTLEK
PROGRAM 4
ROLLING
PROGRAM 13
PRECIPICE
USER SETTING PROGRAM
PROGRAM 14
USER 1
PROGRAM 15
USER 2
PROGRAM 16
USER 3
PROGRAM 17
USER 4
Customer Service 1-888-707-1880
or email [email protected]
15
Dyaco Canada Inc. ©2014
HEART RATE PROGRAM PROFILES:
PROGRAM 18
55% H.R.C.
PROGRAM 19
65% H.R.C.
PROGRAM 20
75% H.R.C.
PROGRAM 21
85% H.R.C.
PROGRAM 22
TARGET H.R.C.
BODY FAT TEST PROGRAMS:
PROGRAM 23
BODY FAT (STOP MODE)
BODY FAT (START MODE)
One of the Following Six Profiles Will Display Automatically after Measuring Your BODY FAT:
Workout Time: 40 minutes
Workout Time: 40 minutes
Workout time: 20 minutes
Workout Time: 40 minutes
Workout Time: 40 minutes
Workout time: 20 minutes
Customer Service 1-888-707-1880
or email [email protected]
16
Dyaco Canada Inc. ©2014
USER DIRECTION
HOW TO USE THE EXERCISE BIKE
HOW TO ADJUST THE HEIGHT OF THE SEAT
For effective exercise, the seat should be at the
proper height. As you pedal, there should be a slight
bend in your knees when the pedals are in the lowest
position. To adjust the seat, first loosen the
adjustment knob a few turns. Next, pull the knob outward,
slide the seat post upward or downward to the desired position,
and then release the knob. Move the seat post upward or
downward slightly to make sure that the knob is engaged
in one of the adjustment holes in the seat post. Then, tighten the
knob.
HOW TO ADJUST HORIZONTAL POSITION
OF THE SEAT
If you want to adjust horizontal position of
the seat, first you can release the club knob.
Next, move the seat forward or backward.
Then retighten the knob after you find the
desired position.
SEAT
HOLE
KNOB
SEAT POST
SEAT
CLUB KNOB
HOW TO ADJUST THE HANDLEBAR
To adjust the angle of handlebar, first loosen
the T type knob. Then turn the handlebar
downward or upward slightly to the proper
position and tighten the knob
HANDLEBAR
T TYPE KNOB
Customer Service 1-888-707-1880
or email [email protected]
17
Dyaco Canada Inc. ©2014
HOW TO ADJUST THE PEDAL STRAPS
The strap for the pedal is adjustable.
Please select the proper holes to fix the straps.
HOW TO MOVE THE EXERCISE BIKE
The bike can be easily moved from room to room.
Grasp the handlebar and pulling back on handles,
tip machine towards you.
HOW TO LEVEL THE EXERCISE BIKE
The bike is equipped with adjustable end caps.
If the unit is wobbly, please turn the leveling caps on
the rear stabilizer to level the unit.
Customer Service 1-888-707-1880
or email [email protected]
18
Dyaco Canada Inc. ©2014
MAINTENANCE
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the reed switch should be adjusted. To
adjust the reed switch, the chain cover (42) must first be removed.
Remove the quick release knob (11), seat post cover (17) and seat post (7).
Remove the left pedal (10) from the crank (38).
Remove the two self-tapping screws (45) from each side of chain cover (42). Remove
another seven ST5 x 15 self-tapping screws (40) from left chain cover (42L). Remove the
crank cover (43) from the chain cover (42). Hold the chain cover (42) near the back and pull it
apart slightly until the chain cover can be lifted off the ends of the crank (38). Do not pull the
chain cover apart at the top or the seam may be broken.
7
40
40
45
9
17
11
40
40
40
10
1
40
45
38
Next, locate the sensor wire (57). Turn the pulley until the magnet is aligned with the reed
switch. Loosen, but do not remove, the ST5 x 15 screw (40). Slide the reed switch slightly
toward or away from the magnet. Make sure that the magnet will not hit the reed switch.
Retighten the screw (40). Turn the pulley for a moment. Repeat until the console displays
correct feedback.
40
51
57
When the Reed Switch is correctly adjusted, reattach the Chain Cover and the Crank Covers.
Customer Service 1-888-707-1880
or email [email protected]
19
Dyaco Canada Inc. ©2014
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip while you are pedaling, even when the resistance is adjusted to
the highest level, the drive belt may need to be adjusted. To adjust the drive belt, the right
chain cover (42R) must first be removed.
Next, turn the nut (65) on clockwise to tighten the eye bolt (64).
When the belt is correctly adjusted, reattach the chain cover and the crank covers.
65
64
Customer Service 1-888-707-1880
or email [email protected]
20
Dyaco Canada Inc. ©2014
PART LIST
Key No.
01
02
03
04
05
06
07
08
09
09S
10
10S
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Part
6720001
6720002
6720003
6720004
6720005
6720006
6720007
6720008
6720009
6720009S
6720010
6720010S
6720011
6720012
6720013
6720014
6720015
6720016
6720017
6720018
6720019
6720020
6720021
6720022
6720023
6720024
6720025
6720026
6720027
6720028
6720029
6720030
6720031
6720032
6720033
6720034
6720035
6720036
6720037
6720038
Customer Service 1-888-707-1880
or email [email protected]
Description
Main frame
Front stabilizer
Rear stabilizer
Upright
Handlebar
Computer
Seat Post
Seat
Left pedal
Left pedal Strap
Right pedal
Right pedal Strap
Quick release knob
Flat washer Φ8*Φ17
Spring washer Φ8
Nylon Nut M8
Allen screw M8*75
Curved washer Φ8*Φ20
Cover for seat post
Allen screw M8*16
Seat adjustment knob
Hand pulse wire
T-type knob
Allen screw M8*20
Roller wheel for front stabilizer
Leveling end cap for rear stabilizer
Clamp
Hand pulse sensor
Screw for computer M5*10
Foam grip
End cap for handlebar
Self tapping screw ST 4*20
Flat washer Φ4.2*Φ12
Grommet
Extension computer wire
Lower computer wire
Sliding tube
Towel rack
Cover for clamp
Crank w/pulley
21
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
5
7
5
4
8
1
4
1
2
1
2
2
2
1
2
4
2
2
2
2
1
1
1
1
1
1
1
Dyaco Canada Inc. ©2014
PART LIST
Key No.
39
40
41
42L
42R
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Part
6720039
6720040
6720041
6720042L
6720042R
6720043
6720044
6720045
6720046
6720047
6720048
6720049
6720050
6720051
6720052
6720053
6720054
6720055
6720056
6720057
6720058
6720059
6720060
6720061
6720062
6720063
6720064
6720065
6720066
6720067
6720068
6720069
6720070
6720071
6720072
6720073
6720074
6720075
6720076
6720077
6720078
6720079
Customer Service 1-888-707-1880
or email [email protected]
Description
Bushing
Self tapping screw ST 5*15
Magnet assembly
Chain cover left
Chain cover right
Crank cover
Spacer for magnet assembly
Self tapping screw
Hex head bolt M8*105
Carriage bolt M8*40
Square plate
Small bushing
Idler wheel
Sensor bracket
Hex head bolt M6*25
Hex head nut M6
Flange nut
Belt
Bearing assembly
Sensor wire
Flywheel
Spring for magnet assembly
Motor
Power wire
Motor cable
Spring for idler wheel
Eye bolt
Nut M8
Powder spacer
Nut M10
Bowl shaped spacer
Bearing 6000
Bearing 6900
Axle for flywheel
Copper washer
Spring clutch
Small pulley
Bottle holder
Adaptor
Audio wire
Box wrench
Allen key 6mm
22
Qty
1
12
1
1
1
2
2
6
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
3
1
1
1
1
1
1
1
1
1
1
Dyaco Canada Inc. ©2014
Customer Service 1-888-707-1880
or email [email protected]
9
58
27
4
16
18
16
45
32
63
64
18
28
66
11
22
23
13
40
61
3
57
1
7
8
16 24
38
15
56
35
28
21 13
55
17
39
75
25 22
37
31
26
50
65
5
30
20
26
29
33
14 12
73 67
34
69 74
71
54
67
51 40
54
69 70
72
68 69
62
59
23
15 16
53
46
40
13
40
52
44
60
40
12
23 2
56
40
40
14
43
24
40
41
45
42L 45
77
27
6
45
47 36
48
49
19
12
14
42R
45
10
43
DIAGRAM
Dyaco Canada Inc. ©2014
TROUBLE SHOOTING
Problem
Cause
Correction
Adaptor not plugged in
Plug adaptor in
Monitor does not display
Computer wires not connected
Sensor wire not connected
No speed or distance
displays on the monitor
No tension
Heart rate not displaying
Grinding noise
Squealing
E1 Monitor cannot read
the signal change (level
change or level change
cannot reach target
position) from the gear
motor.
Sensor wire not working properly
Replace sensor wire
Monitor not working properly
Replace monitor
Magnetic
properly
wheel
Replace magnetic wheel
Computer
properly
wires
not
working
Pulse wire not connected
Hand pulse defective
Monitor not working properly
Crank bearing defective
Idler pulley defective
Flywheel defective
Ensure the computer wires are
connected properly at the
upright and the computer
Securely plug wires together
Replace hand pulse grip
Replace monitor
Replace crank bearings
Replace idler pulley
Replace Flywheel
V-belt slipping
Adjust v-belt
monitor has problem
Replace monitor
The connection cables from monitor
to gear motor are damaged or
disconnected. Pins of the connector
are bent or not fix well.
Check all computer plugs and
wires are connected firmly.
Gear Motor damage or circuit on
the gear motor is abnormal.
Replace gear motor
Wire cable from gear motor to
magnetic system is too short to
drive the magnetic system or
position is not correct.
Adjust the length of motor wire
to make sure there are enough
space to drive the motor.
not
connected
E2 The computer
EEPROM has problem (EEPROM
cannot interface with the
is installed incorrect)
IC chip.
E3
Ensure the computer wires are
connected properly at the
upright and the computer
Ensure the computer wires are
connected properly at the
upright and the computer
The gear motor cannot read the
signal change from the level one
within 4 seconds after press the
start button.
Replace monitor.
Replace gear motor
Maintenance
The safety of this produce can be maintained only if regular periodic checks are made. Most checks
can be performed once a week. However some checks should be made before each workout, and are
indicated as such below.
Customer Service 1-888-707-1880
or email [email protected]
24
Dyaco Canada Inc. ©2014
Checks
 Check that seat nuts are secure, check before each workout.
 Check that pedals are tight, pedals can work loose over time.
 Check that stabilizer bolts are tight, check before each workout this.
 Check that handlebar is secure, if not, tighten, check before each workout this.
 Should a part become defective, replace it immediately. Do not allow use of the equipment until it
has been repaired.
Cleaning
Almost all surfaces are washable. A damp cloth is sufficient to clean most surfaces of this unit. Be
careful not to drip water on the monitor. A mild liquid soap may be added if needed.
TRAINING GUIDELINES
Exercise
Exercise is one of the most important factors in the overall health of an individual. Listed among its
benefits are:






Increased capacity for physical work (strength endurance)
Increased cardiovascular (heart and arteries/veins) and respiratory efficiency
Decreased risk of coronary heart disease
Changes in body metabolism, e.g. losing weight
Delaying the physiological effects of age
Physiological effects, e.g. reduction in stress, increase in self-confidence, etc.
Basic Components of Physical Fitness
There are four all encompassing components of physical fitness and we need to briefly define each
and clarify its role.
Strength is the capacity of a muscle to exert a force against resistance. Strength contributes to
power and speed and is of great importance to a majority of sports people.
Muscular Endurance is the capacity to exert a force repeatedly over a period of time, e.g. it is
the capacity of your legs to carry you 10 Km without stopping.
Flexibility is the range of motion about a joint. Improving flexibility involves the stretching of
muscles and tendons to maintain or increase suppleness, and provides increased resistance to
muscle injury or soreness.
Cardio-Respiratory Endurance is the most essential component of physical fitness. It is the efficient
functioning of the heart and lungs
Aerobic Fitness
The largest amount of oxygen that you can use per minute during exercise is called your maximum
oxygen uptake (MVo2). This is often referred to as your aerobic capacity.
The effort that you can exert over a prolonged period of time is limited by your ability to deliver oxygen
to the working muscles. Regular vigorous exercise produces a training effect that can increase your
aerobic capacity by as much as 20 to 30%. An increased MVO2 indicates an increased ability of the
heart to pump blood, of the lungs to ventilate oxygen and of the muscles to take up oxygen.
Anaerobic Training
This means “without oxygen” and is the output of energy when the oxygen supply is insufficient to
meet the body’s long term energy demands. (For example, 100 meter sprint).
The Training Threshold
This is the minimum level of exercise which is required to produce significant improvements in any
Customer Service 1-888-707-1880
or email [email protected]
25
Dyaco Canada Inc. ©2014
physical fitness parameter.
Progression
As your become fitter, a higher intensity of exercise is required to create an overload and therefore
provide continued improvement
Overload
This is where you exercise at a level above that which can be carried out comfortably. The intensity,
duration and frequency of exercise should be above the training threshold and should be gradually
increased as the body adapts to the increasing demands. As your fitness level improves, so the
training threshold should be raised.
Working through your program and gradually increasing the overload factor is important.
Specificity
Different forms of exercise produce different results. The type of exercise that is carried out is specific
both to the muscle groups being used and to the energy source involved.
There is little transfer of the effects of exercise, i.e. from strength training to cardiovascular fitness.
That is why it is important to have an exercise program tailored to your specific needs.
Reversibility
If you stop exercising or do not do your program often enough, you will lose the benefits you have
gained. Regular workouts are the key to success.
Warm Up
Every exercise program should start with a warm up where the body is prepared for the effort to
come. It should be gentle and preferably use the muscles to be involved later.
Stretching should be included in both your warm up and cool down, and should be performed after
3-5 minutes of low intensity aerobic activity or callisthenic type exercise.
Warm Down or Cool Down
This involves a gradual decrease in the intensity of the exercise session. Following exercise, a large
supply of blood remains in the working muscles. If it is not returned promptly o the central circulation,
pooling of blood may occur in the muscles
Heart Rate
As you exercise, so the rate at which your heart beat also increases. This is often used as a measure
of the required intensity of exercise. You need to exercise hard enough to condition your circulatory
system, and increase your pulse rate, but not enough to strain your heart.
Your initial level of fitness is important in developing an exercise program for you. If you are starting
off, you can get a good training effect with a heart rate of 110-120 beats per minute (BPM). If you are
fitter, you will need a higher threshold of stimulation.
To begin with, you should exercise at a level that elevates your heart rate to about 65 to 70% of your
maximum. If you find this is too easy, you may want to increase it, but it is better to lean on the
conservative side.
As a rule of thumb, the maximum heart rate is 220 minus your age. As you increase in age, so your
heart, like other muscles, loses some of its efficiency. Some of its natural loss is won back as fitness
improves.
The following table is a guide to those who are “starting fitness”.
Age
25
30
35
40
45
50
55
60
65
Target heart Rate
10 Second Count
23
22
22
21
20
19
19
18
18
Beats per Minute
138
132
132
126
120
114
114
108
108
Pulse Count
The pulse count (on your wrist or carotid artery in the neck, taken with two index fingers)is done for
ten seconds, taken a few seconds after you stop exercising. This is for two reasons: (a) 10 seconds is
long enough for accuracy, (b) the pulse count is to approximate your BPM rate at the time you are
exercising. Since heart rate slows as you recover, a longer count isn’t as accurate.
Customer Service 1-888-707-1880
or email [email protected]
26
Dyaco Canada Inc. ©2014
The target is not a magic number, but a general guide. If you’re above average fitness, you may work
quite comfortably a little above that suggested for your age group.
The following table is a guide to those who are keeping fit. Here we are working at about 80% of
maximum.
Age
25
30
35
40
45
50
55
60
65
Target heart Rate
10 Second Count
26
26
25
24
23
22
22
21
20
Beats per Minute
156
156
150
144
138
132
132
126
120
Don’t push yourself too hard to reach the figures on this table. It can be very uncomfortable if you
overdo it. Let it happen naturally as you work through your program. Remember, the target is a guide,
not a rule, a little above or below is just fine.
Two final comments:(1) don’t be concerned with day to day variations in your pulse rate, being under
pressure or not enough sleep can affect it;(2) your pulse rate is a guide, don’t become a slave to it.
Endurance Circuit Training
Cardiovascular endurance, muscle, strength, flexibility and coordination are all necessary for
maximum fitness. The principle behind circuit training is to give a person all the essentials at one time
by going through your exercise program moving as fast as possible between each exercise. This
increases the heart rate and sustains it, which improves the fitness level. Do not introduce this circuit
training effect until you have reached an advanced program stage.
Body Building
Is often used synonymously with strength training The fundamental principal here is OVERLOAD.
Here, the muscle works against greater loads than usual. This can be done by increasing the load
you are working against.
Patronization
This is the term used to vary your exercise program for both physiological and psychological benefits.
In your overall program, you should vary the workload, frequency and intensity. The body responds
better to variety and so do you. In addition, when you feel yourself getting “stale’, bring in periods of
lighter exercise to allow the body to recuperate and restore its reserves. You will enjoy your program
more and feel better for it.
Muscle Soreness
For the first week or so, this may be the only indication you have that you are on an exercise program.
This, of course, does depend on your overall fitness level. A confirmation that you are on the correct
program is a very slight soreness in most major muscle groups. This is quite normal and will
disappear in a matter of days.
If you experience major discomfort, you may be on a program that is too advanced or you have
increased your program too rapidly.
If you experience PAIN during or after exercise, your body is telling your something.
Stop exercising and consult your doctor.
What to Wear
Wear clothing that will not restrict your movement in any way while exercising. Clothes should be light
enough to allow the body to cool. Excessive clothing that causes you to perspire more than you
normally would while exercising, gives you no advantage. The extra weight you lose is body fluid and
will be replaced with the next glass of water you drink. It is advisable to wear a pair of gym or running
shoes or “sneakers”.
Breathing during Exercise
Do not hold your breath while exercising. Breathe normally as much as possible. Remember,
breathing involves the intake and distribution of oxygen, which feeds the working muscles.
Rest periods
Once you start your exercise program, you should continue through to the end. Do not break off
Customer Service 1-888-707-1880
or email [email protected]
27
Dyaco Canada Inc. ©2014
halfway through and then restart at the same place later on without going through the warm-up stage
again.
The rest period required between strength training exercises may vary from person to person. This
will depend mostly on your level of fitness and the program you have chosen. Rest between exercises
by all means, but do not allow this to exceed two minutes. Most people manage with half minute to
one minute rest periods.
STRETCHING
Stretching should be included in both your warm up and cool down, and should be performed
after 3-5 minutes of low intensity aerobic activity or callisthenic type exercise. Movements
should be performed slowly and smoothly, with no bouncing or jerking. Move into the stretch
until slight tension, not pain, is felt in the muscle and hold for 20-30 seconds. Breathing
should be slow, rhythmical and under control, making sure never to hold your breath.
HEAD ROLLS
Rotate your head to the right for one count, feeling
the stretch up the left side of your neck. Next rotate
your head back for one count, stretching your chin to
the ceiling and letting your mouth open. Rotate your
head to the left for one count, and finally, drop your
head to your chest for one count.
SHOULDER LIFTS
Lift your right shoulder up toward your ear
for one count. Then lift your left shoulder
up for one count as you lower your right
shoulder.
SIDE STRETCHES
Open your arms to the side and continue lifting
them until they are over your head. Reach your
right arm as far upward toward the ceiling as
you can for one count. Feel the stretch up
your right side. Repeat this action with your
QUADRICEPS STRETCH
With one hand against a wall for balance,
reach behind you and pull your right foot up.
Bring your heel as close to your buttocks as
possible. Hold for 15 counts and repeat with
left foot up.
left arm.
Customer Service 1-888-707-1880
or email [email protected]
28
Dyaco Canada Inc. ©2014
INNER THIGH STRETCH
Sit with the soles of your feet together with your
knees pointing outward. Pull your feet as close
Into your groin as possible. Gently push your
knees towards the floor. Hold for 15 counts.
TOE TOUCHES
Slowly bend forward from your waist, letting
your back and shoulders relax as you stretch
toward your toes. Reach down as far as you
can and hold for 15 counts.
HAMSTRING STRETCHES
Sit with your right leg extended. Rest the sole of
your left foot against your right inner thigh. Stretch
your toe as far as possible. Hold for 15 counts.
Relax and then repeat with left leg extended.
CALF / ACHILLES STRETCH
Lean against a wall with your left leg in front
of the right and your arms forward. Keep toward
your right leg straight and the left foot on the
floor then bend the left leg and lean forward
by moving your hips toward the wall. Hold, then
repeat on the other side for 15 counts.
Customer Service 1-888-707-1880
or email [email protected]
29
Dyaco Canada Inc. ©2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement