Microsoft Word Viewer - Troubleshooting

Microsoft Word Viewer - Troubleshooting
TASSIMO TROUBLESHOOTING
In the table below are solutions to problems that may occur.
PROBLEM
All the
indicator
lights are
flashing.
SITUATION
1. Machine not prepared for
use.
2. Water level is too low.
3. Water container not fitted
correctly
4. No T DISC in machine.
5. T DISC not read or damaged.
6. Piercing unit blocked.
7. The machine may require
descaling.
8. Internal machine fault.
SOLUTION
1. Follow the procedure "Preparing Your Machine
for Use".
2. Refill the water container.
3. Place a T DISC, label side down, on the T DISC
holder and close the brew mechanism.
4. Clean the bar code reading window or
replace the T DISC.
5. Remove and clean the piercing unit.
6. Descale the machine following the "Descaling"
procedure.
7. Contact Tassimo Customer Service
1-877-TDISCS1 (1-877-834-7271).
The machine
will not move
past
STANDBY.
The brew mechanism may not be
closed properly.
The "Auto
Mode" is not
working.
Bar code reader may not be able to Clean the bar code reading window. Replace the T
read the T DISC label.
DISC. You can still enjoy your preferred drink by
using the "Manual Mode".
My cup is
overflowing.
Each drink has been formulated to
produce the perfect amount of
liquid. Be sure that you are using
the right sized cup for your drink.
My cup doesn’t The cup stand is too close to the
brew mechanism.
fit.
Liquid is
splashing out
of the cup.
Make sure that a T DISC is placed on the T DISC
holder and the brew mechanism is firmly closed.
Ensure that you use the following recommended cup
sizes:
Espresso
Filter Coffee, Café Crema,
Cappuccino, Latte, Tea
and Chocolate
3 oz / 90 ml cup
11 oz / 325 ml cup
Try lowering the cup stand to fit your cup. You can
also temporarily remove the cup stand and drip tray,
leaving the backsplash in place.
Cup is placed too far away from the Adjust the height of the cup stand up to ensure that
brew mechanism.
the cup is closer to the brew mechanism.
The machine is
leaking from
the brew
mechanism.
1. T DISC is damaged or
leaking.
2. The piercing unit is not fitted
properly.
The machine is
leaking from
1. Drip tray is full of water.
2. Backsplash is not properly
Press the start/stop button to stop the brew cycle.
Slowly open the brew mechanism, remove the T
DISC, and clean the inside of the brew mechanism.
Remove and refit the piercing unit.
TURN OFF AND UNPLUG MACHINE
the bottom.
fitted.
3. Water expansion outlet is
not properly descaled.
4. Water container is not
properly fitted
5. Piercing unit is missing or
damaged (check the rubber
seal around it)
1. Empty the removable drip tray.
2. Remove and refit the backsplash, cup stand,
and drip tray back on the machine.
3. Clean the water expansion outlet using a
clean cloth moistened with white vinegar.
4. Refit the water container.
5. Refit piercing unit if available; or call customer
service for replacement piercing unit and
replace
My drinks are
brewing
smaller than
usual.
The machine may require
descaling.
Descale the machine following the "Descaling"
procedure.
I have lost my
cleaning disc.
A cleaning disc is needed to rinse
and descale the machine.
Contact Tassimo Customer Service
1-877-TDISCS1 (1-877-834-7271).
My machine is
not operating;
there are no
lights
illuminated.
The electrical supply may not be
connected properly.
Check that the machine is properly plugged into the
electrical supply. Check the on/off switch at the back
of the machine.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement