SignaMax Gigabit Ethernet Media Converters Guide

Add to my manuals
13 Pages

advertisement

SignaMax Gigabit Ethernet Media Converters Guide | Manualzz
Gigabit Ethernet SFP Media Converter
Signamax
 Connectivity Systems
Gigabit Ethernet SFP Media Converter
Model - 065-1195SFP
065-1195SFPI
User’s Guide
1
Gigabit Ethernet SFP Media Converter
Quick Start Guide
This quick start guide describes how to install and use the Gigabit Ethernet SFP media
converter. The converter introduced here provides a one channel media conversion solution.
Physical Description
Product Overview
This Gigabit Ethernet SFP media converter is a plug-and-play device. Connect the supplied AC
to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter,
and then attach the plug into a standard AC outlet with a voltage range from 100 to 240V AC.
DIP Switch
DIP
switch
Up (Default Setting)
Down
Left-hand
side
The fiber port auto detects
full and half duplex
Forces the fiber port to full
duplex mode
Right-hand
side
Disable LFS
Enable LFS
The 1000BaseT and 1000BaseSX/LX Connectors
The 1000BaseT
Connection
The following lists the pinouts of the
1000BaseT port.
The 1000BaseSX/LX
Connection
The SFP socket accepts standard Gigabit
Ethernet Small Form-factor Pluggable (SFP)
modules of various types and spectra.
2
LFS:
Link fault signaling
function
Gigabit Ethernet SFP Media Converter
The Port Status LEDs
LEDs
Power
LNKC
State
Steady
Off
Steady
LNKF
Steady
FX port: A valid network connection is established.
LNKF stands for LINK/Fiber
Off
Indication
Power on
No power
TX port: A valid network connection is established.
LNKC stands for LINK/Copper
No connection
Off
No connection
FDX/COL
Steady
RX
Steady
Off
Steady
Off
Connection has been made in full duplex mode.
FDX stands for FULL DUPLEX
Receiving data
No reception
Transmitting data
No transmission
TX
Functional Description
•
•
•
•
•
•
•
•
DIP switch configuration for Link Fault Signaling enable/disable and
fiber auto/force mode.
1000 Mbps, Auto/Full-duplex, Auto-Negotiation, Auto-MDI/MDIX.
SFP socket for Gigabit fiber optic expansion.
Full wire-speed forwarding rate.
0.8A 12VDC external universal power supply.
32℉ to 113℉ (0℃ to 45℃) operating temperature range.
Aluminum case.
Supports wall mounting installations or can be used with the 065-1185
media converter chassis system.
3
Gigabit Ethernet SFP Media Converter
FCC Statement
The FCC (Federal Communications Commission) restricts the amount of
radio frequency emission and radiation coming from computer equipment.
The equipment introduced in this manual has been tested and found to
comply with the limits for a Class A digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user is required to correct the interference at
his/her own expense.
Any changes or modifications not expressly approved by the manufacture
would void the user’s authority to operate the equipment.
4
Gigabit Ethernet SFP Media Converter
Trademarks
Product names mentioned in this manual may be trademarks or registered
trademarks of those products.
All trademarks or brand names mentioned are properties of their respective
companies.
5
Gigabit Ethernet SFP Media Converter
Preface
This manual describes how to install and use the 065-1195SFP Gigabit
Ethernet SFP Media Converter. The Converter introduced here provides a
one channel media conversion solution:
This media converter supports a 1000BaseT to 1000Base connection
(multimode or singlemode fiber, in a variety of light spectra and span
lengths) with a Link Fault Signaling function.
A variety of Small
Form-factor Pluggable (SFP) modules allow a wide choice of available fiber
types and spanning distances to be used in the same converter model.
The Link Fault Signaling function allows a link failure on either the
1000Base fiber optic connection or the 1000BaseT twisted-pair Gigabit
Ethernet connection to be propagated to a like device at the opposite end of
the fiber optic channel. This is useful when managed switches are used in
a network, so that a dropped link on either twisted-pair connection or the
fiber optic cable will be shown to the switch at the other end of the circuit for
Spanning Tree/Rapid Spanning Tree circuit reconfiguration by the
connected managed switches. It is switch-defeatable for use during the
initial circuit setup or if managed switches are not used.
The Gigabit Ethernet Media Converter fully complies with IEEE802.3ab
1000BaseT and IEEE802.3z 1000BaseSX/LX Gigabit Ethernet standards.
In this manual, you will find:
Product overview
Features on the media converter
Illustrative LED functions
Installation instructions
Specifications
6
Gigabit Ethernet SFP Media Converter
Table of Contents
Quick Start Guide .....................................................2
Physical Description ........................................................2
Functional Description ....................................................3
FCC Statement ..........................................................4
Trademarks ...............................................................5
Preface .......................................................................6
Table of Contents ......................................................7
Introduction ..............................................................8
Product Overview............................................................8
Product Features .............................................................8
Packing List .....................................................................9
One-Channel Media Converter .............................. 10
Physical Ports ................................................................ 10
Port Status LEDs........................................................... 10
Installation............................................................... 11
Selecting a Site for the Equipment ................................ 11
Connecting to Power ..................................................... 11
Installing in a Chassis.................................................... 11
Specifications........................................................... 12
Contact Information ............................................... 13
7
Gigabit Ethernet SFP Media Converter
Introduction
The 065-1195SFP Gigabit Ethernet SFP Media Converter provides one
channel for media conversion between 1000BaseT and 1000BaseSX/LX
with a Link Fault Signaling function. It can be used as a stand-alone device
or with the Signamax 065-1185 16-bay Rack Mount Chassis (mountable in
a standard 19” rack) as shown below.
Product Overview
Product Features
One-channel media conversion between: 1000BaseT and 1000BaseSX/LX using SFP
modules; a SFP socket is provided to accommodate Gigabit Ethernet SFP’s.
Fiber media can be either multimode fiber, singlemode fiber, or WDM singlemode fiber.
Full wire-speed forwarding rate.
Front panel status LEDs.
Used as a standalone device or with the Signamax 065-1185 rack mount chassis.
Hot-swappable when used with the Signamax 065-1185 rack mount chassis.
A connection to the TX port must be made before making a connection to the fiber port, so
that a link condition will be sensed on the fiber port whenever the media converter detects
a link condition on the TX port.
There are two pins on the DIP switch of the 1000BaseT and 1000BaseSX/LX
one-channel media converter:
Toggle up the pin on the left-hand side to let the fiber port auto detect full and half
duplex.
Toggle down the pin on the left-hand side to force the fiber port to full duplex
mode.
Toggle up the pin on the right-hand side to disable the link-fault-pass-through
function.
Toggle down the pin on the right-hand side to enable the link-fault-pass-through
function.
DIP
Switch:
Up (Default Setting):
Down:
Left-hand
side
The fiber port auto
detects full and half
duplex
Force the fiber port to full
duplex mode
Right-hand
side
Disable LFS
Enable LFS
Notes:
LFS: Link Fault
Signaling function
The fiber port should be forced to full duplex mode when two 1000BaseT and
1000BaseSX/LX one-channel media converters are connected to each other via fiber port.
The TX port auto detects full and half duplex
The TX port supports auto MDIX for uplink purpose
8
Gigabit Ethernet SFP Media Converter
Packing List
When you unpack this product’s package, you will find the items listed
below. Please inspect the contents, and report any apparent damage or
missing items immediately to your authorized reseller.
The Media Converter
User’s Manual
AC to DC Power Adaptor
9
Gigabit Ethernet SFP Media Converter
One-Channel Media Converter
Physical Ports
065-1195SFP -- 1000BaseT to 1000Base SFP Media Converter
This converter provides one TX port and one Gigabit SFP socket. The
Gigabit SFP socket provides the option of using multimode, singlemode, or
WDM singlemode fiber with the appropriate SFP module. The TX port uses
a RJ-45 connector and supports auto-MDIX for uplink purposes.
Port Status LEDs
The LED indicators give you instant feedback on the status of the converter:
LEDs
Power
LNKC
State
Steady
Off
Steady
LNKF
Steady
FX port: A valid network connection is established.
LNKF stands for LINK/Fiber
Off
Indication
Power on
No power
TX port: A valid network connection is established.
LNKC stands for LINK/Copper
No connection
Off
No connection
FDX/COL
Steady
RX
Steady
Off
Steady
Off
Connection has been made in full duplex mode.
FDX stands for FULL DUPLEX
Receiving data
No reception
Transmitting data
No transmission
TX
10
Gigabit Ethernet SFP Media Converter
Installation
This chapter gives step-by-step installation instructions for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not
be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
The ambient temperature should be between 32 and 113 degrees
Fahrenheit (0 to 45 degrees Celsius).
The relative humidity should be less than 95 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic
field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
Make sure that the equipment receives adequate ventilation. Do not
block the ventilation holes of the equipment.
The power outlet should be within 6 feet (1.8 meters) of the product.
Connecting to Power
This Converter is a plug-and-play device.
Connect the supplied AC to DC power adapter to the receptacle at the back of the
converter.
Attach the plug into a standard AC outlet with a voltage range from 100 to 240 VAC.
Installing in a Chassis
The 065-1195SFP Converter is designed to fit into any of the expansion
slots on a Signamax 065-1185 rack mount chassis.
Unscrew the carrier from the desired expansion slot on the chassis.
Fit the converter onto the carrier.
When the converter is completely seated onto the carrier, insert the carrier to the guide
rails of the expansion slot.
Carefully slide in the carrier until it is fully and firmly fit the chassis.
Fasten the carrier to the chassis by the screws.
<NOTE>
Never insert any converter into the chassis directly without
using the supplied carriers. The carriers allow secure and consistent
placement of the converters into the chassis’ backplane without causing any
damage.
11
Gigabit Ethernet SFP Media Converter
Specifications
Applicable Standards
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
Fixed Ports
1000BaseT to 1000BaseSX/LX:
Speed
1 TX port, 1 Gigabit SFP socket
1000/2000Mbps for half/full-duplex
Forwarding rate
1,488,100pps for 1000Mbps
LED Indicators
1000T to 1000SX/LX:
Power; TX; RX; FDX/COL; LNKF; LNKC
Dimensions
3.16” (W) × 4.3” (D) × 0.94” (H)
(80.3mm (W) × 109.2mm (D) × 23.8mm (H))
Weight
Power
0.33lb (150 g.)
External power adaptor
0.2A @ 12VDC
2.4 Watts Maximum
32°F ~ 113°F (0°C ~ 45°C)
14°F ~ 158°F (-10°C ~ 70°C)
5 ~ 95%, non-condensing
FCC part 15 Class A, CE Mark Class A
Power Consumption
Operating Temperature
Storage Temperature
Humidity
Emissions
Please consult our website at www.signamax.com for product
information and specifications of currently-available Signamax
SFP modules.
12
Gigabit Ethernet SFP Media Converter
Contact Information
SIGNAMAX CONNECTIVITY SYSTEMS
An AESP Company
16295 N.W. 13h Avenue
Miami, Florida 33169, U.S.A.
Phone: 305-944-7710 Fax: 305-949-4483
Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201
Http://www.signamax.com
E-mail: [email protected]
13

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement