Grande ZI0266E security system User Manual

User Manual
User Manual
Catalog Number: ZI0266E (3/06)
All data is subject to change without prior notice.
-2-
Table of Contents
Chapter One: Introduction and Overview ............................................................................................ 4
1.1: Security System Components ................................................................................................ 4
1.2: System Monitoring ................................................................................................................. 5
1.3: Two-Way Audio ...................................................................................................................... 5
1.4: Home Automation .................................................................................................................. 5
Chapter Two: The User Interface ........................................................................................................ 6
2.1: Front Panel Keypad ............................................................................................................... 6
2.2: Keyfobs .................................................................................................................................. 7
2.3: Wireless Keypad .................................................................................................................... 7
Chapter Three: Arming and Disarming ................................................................................................ 9
3.1: Arming the System................................................................................................................. 9
3.2: Disarming the System .......................................................................................................... 10
3.3: Arm Status Indication ........................................................................................................... 10
3.4: Arming Tones....................................................................................................................... 10
Chapter Four: Panic Alarms .............................................................................................................. 11
4.1: Front Panel Keypad Alarms ................................................................................................. 11
4.2: Keyfob Panic Alarm.............................................................................................................. 11
4.3: Wireless Keypad Panic Alarm.............................................................................................. 11
Chapter Five: Home Automation (optional feature) ........................................................................... 12
5.1: Keypad Control .................................................................................................................... 12
5.2: Keyfob Control ..................................................................................................................... 12
5.4: Scheduling ........................................................................................................................... 12
Chapter Six: Two-Way Audio (optional feature) ................................................................................ 14
6.1: Calling your Home................................................................................................................ 14
6.2: Service Call .......................................................................................................................... 15
Chapter Seven: Advanced System Operation ................................................................................... 16
7.1: Stop Communications .......................................................................................................... 16
7.2: Zone Bypassing/Unbypassing.............................................................................................. 17
7.3: User Codes .......................................................................................................................... 17
7.4: Event Log ............................................................................................................................. 19
7.5: Service Menu ....................................................................................................................... 19
Appendix A: Menu Structure.............................................................................................................. 22
Appendix B: Glossary ........................................................................................................................ 23
-3-
Chapter One: Introduction and Overview
This user manual explains all you need to know about your security system and provides
step-by-step instructions for all of its user functions. In addition to the explanation you will
receive from your installer, we urge you to read this manual so that you may take full
advantage of your system’s features. Keep this manual in an accessible location for
future reference.
The security system has many features in order to suit a wide range of applications. This
manual outlines all of these features but it is likely that there are options that are not
relevant to your system. If you have any questions regarding the availability of the
features described in the manual, please ask your installer.
1.1: Security System Components
Your security system is made up of a control panel, various sensors and a number of optional
peripheral devices. This section explains the role of each component in your system.
Control Panel
The control panel is the brain of the system. It
communicates with all the devices connected to the
system. For example, in the event of a burglary, a
sensor sends a signal to the control panel indicating
that it has sensed motion on the premises. On
receiving this signal, the control panel makes the
decision to report the alarm to your monitoring service
and activate the siren.
Sensors
Sensors are the devices that protect your home, alerting the control
panel when there is a breach in security. Magnetic contacts protect
your doors and windows while motion sensors are able to detect an
intruder moving across its field of view.
Keyfobs
Keyfobs are hand-held transmitters that are used to operate the
system. Various keyfobs are available providing a number of
functions. For example, arming/disarming the system and sending
panic alarms.
Keypads
The keypads enable you to communicate with the control panel in
order to perform a number of different functions. The main function
you can perform using a keypad is to arm the system when leaving
your home and to disarm on your return.
Internal Siren
The control panel includes a built-in internal siren that is sounded
during certain alarm conditions to warn you and deter intruders.
-4-
1.2: System Monitoring
When an event occurs within the system, the control panel sends a message to your
monitoring service describing the exact nature of the event. This enables the monitoring
service to take the required action.
A sensor detects.
,
The control panel is alerted.
An alarm is generated and the
monitoring service is notified.
Remember that no security system can prevent emergencies. This system is only
intended to alert you in case of an emergency and should not take the place of prudent
security practices or life and property insurance.
1.3: Two-Way Audio
The control panel’s built-in microphone and speaker can be used for a number of TwoWay Audio features. These features allow you to contact your home directly in the event
of an alarm or simply to check the premises when you are away.
1.4: Home Automation
An optional expansion module can provide you with the ability to control up to 16
individual electrical appliances or lights using the front panel keypad, wireless keypads or
keyfobs. Additionally, each appliance can be programmed to be turned on and off
automatically according to various schedules and system status conditions.
-5-
Chapter Two: The User Interface
There are several methods you can use to operate the system. Apart from the keypad on
the front panel, your system may include a number of peripheral devices such as
keypads and keyfobs.
This chapter provides a brief introduction to each of the devices you can use to operate
the system. It is important that you familiarize yourself with these devices before reading
the following chapters that shall describe system operation in further detail.
2.1: Front Panel Keypad
The control panel’s front panel keypad is the main user interface that provides you with
all the functions you need to control your security system.
Display
System
Status
LEDs
Arming
Keys
Menu
Navigation
Keys
Alphanumeric
Keypad
Home
Automation
Keys
System Status Indicators
The System Status indicators
provide essential information on
the status of the system such
as arm, disarm, alarm and
power failure conditions.
On during arm. Off during disarm.
Flashes after alarm.
On when power is connected. Off when power
is disconnected. Flashes if there is a problem
with AC power or the backup battery.
Service Call Button
The Service Call button enables you to contact the monitoring service
and talk to an operator.
To make a Service Call, press and hold down the Service Call key for a few seconds.
,
Service Call is an optional feature that may not be included with your system.
-6-
Home Automation On/Off Keys
Pressing one of the Home Automation keys followed by the unit number
(01-16) enables you to control lights and appliances in your home.
Pressing both Home Automation keys simultaneously generates an
SOS panic alarm.
ON
OFF
2.2: Keyfobs
The system supports two types of keyfob transmitter. The function of the buttons on each
keyfob are shown below.
Disarm
Full Arm
Personal
Emergency
Part Arm
or Home
Automation
Perimeter Arm
or Home
Automation
4-button keyfob
1-button keyfob
2.3: Wireless Keypad
The system supports up to four wireless keypads. You can use the keypad as an arming
station and generate a panic alarm in the event of emergency.
Home
Automation
On
Battery
Status LEDs
Numeric
Keypad
Arming Keys
Cancel
Home
Automation
Off
-7-
Numeric Keypad
The numeric keypad allows you to arm or disarm the system by entering a user code.
Arming Keys
Three arming keys are available: Full, Part and Perimeter. These keys arm the system
using one of the three arming methods. One-key Arming is an option that is programmed
by your installer. If this option is disabled, you must also enter a user code when arming.
Simultaneously pressing the Full and Perimeter buttons generates a panic alarm.
Home Automation On/Off Keys
Pressing one of the Home Automation keys followed by the unit number (01-16) enables
you to control lights and appliances in your home.
Cancel
The Cancel key clears the keypad in the event that you pressed a key by mistake.
For example, when entering your code you enter a wrong digit, the system waits for you
to enter all four digits before it decides that the code is incorrect. Pressing the Cancel key
causes the keypad to disregard what was previously entered enabling you to start again.
,
If you are in the process of entering your code and six seconds elapse since the last
keystroke, the entry is automatically canceled. In this case, you must re-enter your code
from the beginning.
Battery Status LEDs
Every time a key is pressed, one of the Battery Status LEDs is lit. When the battery
needs to be replaced, the red Low Battery LED is lit.
-8-
Chapter Three: Arming and Disarming
Arming can be defined as turning the system on. When the system is armed, it monitors
the zones that are protected by the sensors. If a sensor detects an intrusion, the system
generates an alarm.
Certain sensors can be programmed by your installer to be active 24 hours a day. These
sensors are always active regardless of system status.
3.1: Arming the System
Three arming modes are available: Full, Part and Perimeter. These modes enable you to
arm your system accordingly to suit different circumstances.
Full Arming
Away arming activates the entire system. This arming method is used
when you intend to leave your home, leaving the premises empty.
Part Arming
This arming method enables you to arm a section of your home while
remaining on a different part of the premises. For example, at night
your family is upstairs while the area downstairs is armed.
Perimeter Arming
Perimeter arming enables you to turn on the perimeter zones (the
windows and doors of your home) enabling you to move freely within
the protected area.
Before arming the system, check that all doors and windows are closed so that the
system is ready for arming.
To arm the system using the keypad:
•
Press one of the three arming keys; the exit delay begins to count down. At the
end of the exit delay, the system is armed.
,
If the One-key Arming option is disabled in programming, you must enter your user code
when arming the system.
To arm the system using a keyfob:
•
Press the relevant button on your keyfob (see 2.2: Keyfobs); the exit delay
begins to count down. At the end of the exit delay, the system is armed.
Forced Arming
Forced arming enables you to arm when the system is not ready. For example, if a door
protected by a magnetic contact is open, you may arm the system on condition that the
door will be closed by the end of the Exit delay. If the door is still open after the exit delay
expires, an alarm is generated.
,
Forced arming is available only if the option is enabled in programming. Forced arming
may be enabled for specific zones or for the entire system.
-9-
3.2: Disarming the System
When you enter the premises, the entry delay begins
to count down. You must disarm the system within the
entry delay time to prevent the system from activating
an alarm.
To disarm the system using the keypad:
•
Enter your user code.
To disarm the system using a keyfob:
•
Press the disarm button – see 2.2: Keyfobs..
3.3: Arm Status Indication
The system’s arm status is displayed on the front
panel’s display only. The following table explains
the various arm status descriptions that appear
on the display.
This…
DISARMED
FULL ARMED
PART ARMED
PERIMETER ARMED
FULL ARMING
PART ARMING
PERIMETER ARMING
,
DISARMED
11:22:02am
Means…
The system is disarmed.
The system has been armed using the displayed arming method.
The system is in the process of arming (displayed during exit delay).
The system may be programmed to display arm status at all times or only for the first two
minutes after you arm or disarm the system.
3.4: Arming Tones
Arming tones are the chimes that the system
FULL ARMING
sounds during the entry/exit delay and when the
7 TO EXIT
system arms or disarms. Various options are
available that determine the pattern of these
tones.
Arming tones may be sounded by either the external siren or the control panel’s built-in
internal siren.
-10-
Chapter Four: Panic Alarms
Panic alarms enable you to send a message to the monitoring service in the event of an
emergency. There are various types of panic alarms and several methods you can use to
generate them.
4.1: Front Panel Keypad Alarms
You can activate two kinds of alarm from
the front panel keypad.
To activate an SOS Panic alarm from
the front panel keypad:
•
Press and hold down the two
SOS keys simultaneously.
To activate a Personal Emergency alarm
from the front panel keypad:
•
Press and hold down keys 4
and 6 simultaneously.
4.2: Keyfob Panic Alarm
To activate a Panic alarm using the fourbutton keyfob:
•
Press the lower two buttons
simultaneously.
Personal Emergency
The one-button keyfob is designed to send a “Personal
Emergency” message to your monitoring service.
The transmitter is water-resistant and can be worn
around the neck as a pendant.
4.3: Wireless Keypad Panic Alarm
To activate a panic alarm from the wireless keypad:
•
Press the Full Arm and Perimeter Arm keys
simultaneously.
-11-
Chapter Five: Home Automation (optional feature*)
Home Automation enables you to control up to 16 individual lights and appliances around
the home. In this section, we shall refer to these lights and appliances as HA units.
HA units can be controlled using the keypad and keyfobs or programmed to react to
specific system status conditions. For example, an HA unit can be programmed to switch
on when the system is armed or when a specific zone is triggered. Additionally, the
Randomize feature is designed to switch lights on and off at night when the system is
armed. This gives potential intruders the impression that the house is occupied.
Scheduling options enable you to program On and Off times for each HA unit. This
feature is found in the main menu. For further information on how to navigate the menu,
refer to Chapter Seven: Advanced System Operation.
5.1: Keypad Control
Two keys on the keypad enable you send On and Off commands to HA units. How an
HA unit reacts to the On command is determined by the installer in programming.
The HA unit can be programmed to switch on until the Off command is received or
automatically switch itself off after a pre-programmed amount of time.
To turn HA units on using the keypad:
1. Press the On key.
2. Enter the two-digit HA unit number (01-16); the chosen HA unit
switches on.
To turn HA units on using the keypad:
1. Press the Off key.
2. Enter the two-digit HA unit number (01-16); the chosen HA unit
switches off.
5.2: Keyfob Control
You can control two separate HA units, using the four-button keyfob. This option can be
programmed by the installer. For further information on keyfob button assignments refer
to 2.2: Keyfobs.
5.4: Scheduling
The Scheduling feature allows you to set an On and Off time for each HA unit. At these
times the system automatically switches the HA unit on and off. You can also choose the
days of the week that the schedule is active.
On Time
To edit an HA unit’s “On” Time:
1. From the main menu, select HA Schedules [8].
2. Select an HA unit.
3. From the HA unit’s sub-menu, select On Time.
4. Enter a time (HH:MM). Press to toggle AM and PM.
5. Press when the desired setting is displayed.
*
Discuss this capability with your security service provider to determine if it is applicable to your
system.
-12-
Off Time
To edit an HA unit’s “Off” Time:
1. From the main menu, select HA Schedules [8].
2. Select an HA unit.
3. From the HA unit’s sub-menu, select Off Time.
4. Enter a time (HH:MM). Press to toggle AM and PM.
5. Press when the desired setting is displayed.
Weekly Schedule
To program the days of the week that the schedule is active:
1. From the main menu, select HA Schedules [8].
2. Select an HA unit.
3. From the HA unit’s sub-menu, select Schedule.
4. Use keys 1 to 7 to toggle the days on and off.
Press…
1
2
3
4
5
6
7
5.
To toggle…
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Press when the desired setting is displayed.
-13-
Chapter Six: Two-Way Audio (optional feature*)
The control panel offers a range of Two-Way Audio (TWA) features. You may use these
features to check your home in the event of an alarm or as an alternative means of
communicating with members of your family. For example, you may wish to call an
elderly person who has difficulty reaching the phone. Using its Two-Way Audio features,
the control panel automatically picks up the call and you can communicate via its built-in
microphone and speaker.
6.1: Calling your Home
You may call your home at any time in order to contact your family or check your home
while you are away. When your security system shares a telephone line with other
devices (e.g. telephones, an answering machine or fax), it is important that the control
panel distinguish between calls so that it knows when to pick up the relevant call. For this
purpose the system employs a double call method.
To call your home:
1. Dial your telephone number.
2. Wait for two or three rings then hang-up.
3. Wait at least five seconds and dial the number again; on the second ring, the
control panel answers the call and sounds two tones.
4. Enter the User TWA code on your telephone – see 6.3: User Codes, Code 29.
,
Do not enter your user code until you hear the two tones. Any digits entered before the
tones are sounded are disregarded by the system.
5.
The duration of the call is an option programmed by your installer. Ten seconds
before the end of the call, two short tones are sounded. To extend the call,
press 7 on your telephone.
To disconnect before the end of the call, press “@” then “#” on your telephone.
6.
,
It is possible that the Two-Way Audio features on your system are programmed to operate
in “Simplex” mode. Simplex mode means that one party may speak while the other party
listens.
If using Simplex mode, the call is connected in Listen mode. In Listen mode, the
microphone on the control panel is turned on so that you can listen in. If you want to
switch to Speak mode, press 1 on your telephone.
In Speak mode, the microphone is turned off and the speaker is turned on so that you can
speak to people at home. If you want to switch back to Listen mode, press 0 on your
telephone.
Siren Silencing
The siren is silenced during Two-Way Audio communication in the event of an alarm. At
the end of the call, the siren is re-activated (if the Siren Cut-Off has not yet expired). You
can cancel the re-activation of the siren by pressing “9” on your telephone during the call.
*
Discuss this capability with your security service provider to determine if it is applicable to your
system.
-14-
6.2: Service Call
The Service Call feature enables you to call the monitoring service by
pressing one key.
To make a Service Call:
•
Press and hold down the Service Call key for a few seconds.
The monitoring station should then respond to your call and you can talk to them
through the microphone on your control panel.
,
Service Call is an optional feature that may not be included with your system.
-15-
Chapter Seven: Advanced System Operation
Besides the basic functions described in the previous chapters, you can access
additional functions via the menu. This chapter describes these functions and the menu
navigation procedure.
Menu Navigation
Using the keypad on the front panel, you can navigate through the menus using the
arrow navigation keys ( / ) and make simple yes/no decisions using the and keys.
The availability of menu items depends on the user code that you used to enter Menu
mode. Some menu items are limited to the Master code only (User 1). Certain menu
items, such as system programming functions, are not intended for the user and can only
be accessed by the installer.
The following example explains the procedure for navigating through the menus to the
View Event Log function (Master code access only). For further information on this
function, see 7.4: Event Log.
1.
2.
3.
4.
5.
Press to enter Menu mode.
Enter the Master code; the first menu item in the main menu, 1. Stop Comm. is
displayed.
Press
until 6. Event Log is displayed.
Press to enter the Event Log menu; 1. View Log is displayed.
Press to choose the displayed item.
Press if you do not want to choose the displayed item. Pressing also takes you
back to the previous menu level.
,
Menu mode automatically terminates two minutes after the last keystroke.
Throughout this chapter, we have tried to include all of the system functions using a
similar structure and order as they appear in the menu. The above procedure provides a
detailed explanation of menu navigation. However, in order to simplify the procedures
that appear in the rest of this chapter, the following conventions are used:
This…
From the Bypass Zones
menu, select Unbypass All.
Select…
[61]
Means…
Enter the main menu by pressing and entering your user code.
Using the arrow keys, navigate until you reach Bypass Zones
and press . Using the arrow keys, navigate until you reach
Unbypass All and press .
Use the arrow keys to scroll through the options and press .
The shortcut to a specific menu item from the main menu. In this
case, this is the shortcut for View Log. These appear in the
procedures as an additional aid to menu navigation.
7.1: Stop Communications
The Stop Communications function enables you to prevent the system from reporting in
the event of a false alarm.
To stop communications:
•
From the main menu, select Stop Com. [1]; all pending messages to the
monitoring service are canceled.
-16-
7.2: Zone Bypassing/Unbypassing
When a zone is bypassed, its sensor is ignored by the system and it does not generate
an alarm when triggered.
To bypass or unbypass a zone:
1. From the Bypass Zones menu, select Bypass/Unbyp. [21].
2. Using the arrow keys, scroll to the zone you want to bypass or unbypass.
3. Press to change the bypass status.
4. Press ; Save Changes? is displayed.
5. Press to confirm the changed bypass status.
To unbypass all zones:
1. From the Bypass Zones menu, select Unbypass All [22].
2. Press ; all zones are unbypassed
,
All bypassed zones will be automatically unbypassed when the system is disarmed.
7.3: User Codes
The control panel supports a variety of individual user codes. Each of these codes is four
digits long. Most system functions require you to enter a valid user code.
The ability to perform a function is defined by your user code’s authorization level. These
authorization levels are pre-defined for each code as explained below.
Code 1: Master Code
The Master code is the highest user authorization level. With the Master code, you can
change all other user codes. Additionally, the Master code provides access to the Event
Log and the Service menu.
,
The system is provided with a default Master code. Change this code immediately after
the system has been installed!
Codes 2-19: Controlled Codes
When you use a controlled user code for arming and disarming, the system notifies the
monitoring service. You can assign these codes to your children or employees whose
comings and goings are of interest to you.
Codes 20-25: Non-controlled Codes
Non-controlled codes do not cause the system to send Arm/Disarm reports to the
monitoring service. The system sends a Disarm report only if you use this code to disarm
the system after an alarm occurrence.
Codes 26-27: Limited Codes
A Limited code enables you to issue a code that is valid for one day only. This code
automatically expires 24 hours after it has been programmed.
Code 28: Duress Code
The Duress code is designed for situations where you are being forced to operate the
system. This user code performs the operation selected, while sending a Duress event
message to the monitoring service.
-17-
Code 29: User Two Way Audio (TWA) Code
The User TWA code is designed to enable you to communicate with the control panel at
any time. This code can only be used for this specific purpose and does not allow access
to any additional system functions such as disarming.
Changing User Codes
User code changing is a feature that is available exclusively to the Master code. To
maintain a high level of security, keep all user codes confidential.
To change a user code:
1. From the main menu select, User Codes [4].
2. Select the code you want to change;
3. From the code’s sub-menu, select Edit Code; the 4-digit code is displayed with
the cursor flashing on the first digit.
4. Enter a new code.
5. Press ; the new code is stored in the memory.
,
If you enter a code that is identical to an existing user code, the panel sounds an error
tone and the new code is not accepted. 0000 is not a valid user code as this value is used
to delete a user code.
Deleting User Codes
As an additional security measure, make certain that you delete any extra codes that are
no longer required.
To delete a user code:
1. From the main menu select, User Codes [4].
2. Select the code you want to delete;
3. From the code’s sub-menu, select Edit Code; the 4-digit code is displayed with
the cursor flashing on the first digit.
4. Enter 0000.
5. Press ; the code is deleted.
,
The Master code cannot be deleted.
User Code Descriptors
Using the keypad on the front panel,
When changing descriptors, use this key to
you can change the 16-character
enter a space before the current character.
user code descriptors and enter the
Use this key to delete the current character.
name or title of the users to whom
the code is allocated.
To enter text, press a key repeatedly to scroll through the characters that appear on the
key. For example, press 6MNO to enter M, N, O, or 6 respectively. You can also use the 1
and 0 keys to enter symbols. After you enter text, the cursor automatically moves to the
next character.
To change a user code descriptor:
1. From the main menu, select User Codes [4].
2. Select a code.
3. From the code’s sub-menu, select Descriptor.
4. Change the descriptor using the keypad.
5. Press when you have finished the change.
-18-
7.4: Event Log
The event log records events that have occurred within your security system. When the log
is full, the oldest events are automatically erased and are replaced by new events.
To view the event log:
1. From the Event Log menu, select View Log
[61]; the most recent event is displayed.
2. Use the arrow keys to scroll through the
events.
3. When you have finished viewing, press to
exit the log.
Press this key to display
the Time/Date stamp or
the default descriptor on
the second row of the
display.
The following example shows the event log entry for a burglary alarm in the Kitchen
(Zone 4) on November 14th 2003. The report was successfully reported to the central
station.
The labeled diagram below shows how the event log display changes each time the
key is pressed.
The event log displays the following information for each event:
™
š
›
œ

The event – a brief description of the
event that occurred.
Zone descriptor – exactly where the
event occurred.
Time/date stamp – the exact time the
event occurred.
Report details – a single character
indicating whether the event was
reported to the central station. The
options available are R: Report Sent,
F: Report Failed or N: No Report.
Default descriptor – in this case the
number of the zone.
™
ALARM
KITCHEN
š
ALARM
11/14/03
12:34a Rœ
›
ALARM
ZONE #4 
7.5: Service Menu
The Service menu includes various functions that enable you to test your system
effectively. You can gain access to the Service menu using the Master code.
Set Time & Date
To set the time:
1. From the Service menu, select Set Time/Date, Set Time [711].
2. Enter the current time.
3. Press ; the time is modified.
,
When setting the time, use the
key to toggle between AM and PM.
To set the date:
1. From the Service menu, select Set Time/Date, Set Date [712].
2. Enter the current date.
3. Press ; the date is modified
-19-
Siren Tests [to be conducted weekly]
To test the internal siren:
•
From the Service menu, select Int. Siren Test [73]; the internal siren is sounded
briefly.
Speaker Test
To test the speaker:
•
From the Service menu, select Speaker Test [74]; a short sequence of chimes
are sounded from the speaker.
Walk Test [to be conducted weekly]
Walk Test mode enables you to test all your system’s sensors without activating an
alarm.
To start Walk Test mode:
1. From the Service menu, select Walk Test [75]; a list of registered sensors
appears.
2. Operate each sensor by opening protected doors and walking in front of motion
sensors; when the system receives a successful transmission from a sensor,
the sensor is removed from the list.
3. When all the sensors are removed from the list, End Walk Test is displayed.
Transmitters
The Transmitters menu offers two choices, TX List and TX Test.
The TX List comprises all registered transmitters and their last reported status.
To view the TX list:
1. From the Service menu, select TX List/Status [76]; the first transmitter on the
list is displayed.
2. Using the arrow buttons, scroll through the transmitter list.
3. When you have finished viewing, press to exit the list.
The TX list displays the following information for
each transmitter:
™
The transmitter’s descriptor
š
The signal strength of the last received
transmission
›
An abbreviation indicating the last received
status of the transmitter.
This…
OK
TA
BT
OS
NA
Means…
The transmitter is functioning correctly
Tamper condition
Battery low
The transmitter is out of
synchronization
The transmitter is inactive
-20-
™ FRONT
DOOR
S=6 OK ›
š
Press this key to
display the transmitter’s
default descriptor .
Notify
your
installer
The second choice, TX Test, enables you to identify transmitters.
In TX Test mode, each time a transmission is received, a chime is sounded and the
activated transmitter is displayed.
To initiate TX Test mode:
1. From the Service menu, select Transmitters, TX Test [762].
2. Activate a sensor or keyfob; the transmitter’s identity is displayed.
3. When you have finished, press to exit TX Test mode.
Audio Volume
To adjust the sensitivity of the microphone and the volume of the speaker:
1. Establish a two-way audio connection.
2. From the Service menu, select Audio Volume [77]; the current setting is displayed.
3. Adjust the setting according to the following table.
Press…
1
4
3
6
4.
To…
Increase microphone sensitivity
Reduce microphone sensitivity
Increase speaker volume
Reduce speaker volume
Press ; the new settings are stored in the memory.
Display Version
To display the system’s software and hardware versions:
•
From the Service menu, select Version [79]; the software (SW) and hardware
(HW) versions are displayed.
Global Chime
Each sensor can be programmed by your installer to cause the system to chime when
activated. For example, the system can be programmed to sound a chime each time the
front door is opened or closed. The Global Chime option, enables you to turn this feature
on and off.
To enable or disable Global Chime:
1. From the Service menu, select Global Chime [711].
2. Select either Enable or Disable.
3. Press when the desired setting is displayed.
,
Global Chime can also be accessed via a convenient shortcut without needing to enter a
valid user code. To access the Global Chime option from Standby mode, press
then .
-21-
Appendix A: Menu Structure
*
Legend:
Installer code required
Master code required
*
-22-
Not applicable
Appendix B: Glossary
A
Armed
The state during which the security system is turned on. In most
cases, when the system is armed, activating a sensor generates an
alarm.
Arming Keys
The three keys on the front panel or keypad that activate one of the
system’s arming options.
B
Bypassed Zone
A sensor which is ignored by the system. No alarm is generated from
a bypassed zone even if its sensor is activated when the system is
armed.
Cancel Key
A key on the wireless keypad that causes the system to disregard
any partially entered code or command that may have mistakenly
been entered.
Chime
A feature that provides audible annunciation when specific sensors
are activated.
C
Code
see User Code
Controlled Code
A user code that causes the system to notify the monitoring service
when used to arm or disarm.
Delay
The exit/entry delay times that allow the user to arm or disarm the
system without generating an alarm.
Descriptor
Custom labels programmed for each user code, zone, keyfob,
keypad etc.
Disarmed
The state during which the security system is turned off. During
disarm only sensors that are defined as 24hr, Panic or Personal
Emergency are capable of generating an alarm.
Duress Code
A user code that generates a silent alarm to indicate that the user is
being forced to operate the system.
D
E
Entry Delay
See Delay
Event Log
A viewable record of events that have occurred within the system.
Exit Delay
See Delay
F
Forced Arming
Arming before the system is ready. If the system is not secured by
the time that the exit delay expires, an alarm is generated.
Front Panel
The main interface located on the front of the control panel
consisting of a keypad and display.
Full Arming
An arming method that activates the entire system when everyone
leaves.
-23-
G
Global Chime
A feature that enables/disables the Chime feature for the entire
system – see Chime.
HA Units
Home Automation Units (abbr.). The lights and appliances in the
home that are controlled by the optional Home Automation feature.
Home Automation
An optional feature that enables the user to control electrical
appliances and lights via the control panel.
H
K
Keyfob
Handheld wireless transmitters used to remotely control the system.
L
Limited Code
Log
A user code that automatically expires 24 hours after it is
programmed.
See Event Log
M
Master Code
The only user code with the ability to program other user codes. The
Master code also has exclusive access to specific system functions.
Non-Controlled
Code
A user code that does not cause the system to notify the monitoring
service when used to arm or disarm. The system only reports if the
code is used to disarm after an alarm.
Panic Alarm
A user initiated event that alerts the monitoring service in the event
of an emergency.
Part Arming
An arming method that is designed to turn on the protection for a
certain section of the premises.
Perimeter Arming
An arming method that is designed to activate the sensors protecting
the doors and windows while enabling residents to move freely on
the premises.
Ready
The state in which all zones are closed and the system is ready to be
armed.
Sensors
The devices installed around the home that alert the panel in the
event of an alarm.
Service Call
A feature that enables the user to contact the monitoring service and
talk to an operator via the control panel.
Stop
Communications
An operation that stops the transmission of any pending messages
to the monitoring service.
System Status
Indicators
Luminous indicators on the front panel that provide information on
the armed and power status of the system.
N
P
R
S
-24-
T
Tones
TWA
TX
Chimes sounded by the control panel’s internal siren.
Two-Way Audio (abbr.)
Transmitter (abbr.)
TX List
A service feature that lists all the system’s registered transmitters,
their last recorded status and signal strength.
TX Test
A service feature that displays the source of the last received
transmission.
U
Unbypass
The restoral of a bypassed zone to its original state.
User Code
A four-digit code that allows certain system functions to be
performed such as arming and disarming the system.
User TWA Code
A user code that enables Two-Way Audio communication.
W
Walk Test
A mode that enables sensors to be tested without generating an
alarm.
Z
Zone
Zone Bypassing
A protected area within the security system.
See Bypassed Zone
-25-
UL NOTICE: This is a “Grade A” system.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires
the following statement for your information.
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient the receiving antenna until interference is reduced or eliminated.
•
Move the receiver away from the control/communicator.
•
Move the antenna leads away from any wire runs to the control/ communicator.
•
Plug the control/communicator into a different outlet so that it and the receiver are on different branch
circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions.
The user or installer may find the following booklet prepared by the Federal Communications Commission helpful:
“Interference Handbook”. This booklet is available from the U.S. Government Printing Office, Washington, DC
20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User’s Manual. Unauthorized changes or modifications could void the user’s authority to operate
the equipment.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that
contains, among other information, the FCC registration number and ringer equivalence number (REN) for this
equipment. If requested, this information must be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not
all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be
connected to the line, as determined by the total RENs, contact the telephone company to determine the
maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. If advance notice is not practical, the telephone company
will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC
if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect
the operation of the equipment. If this happens, the telephone company will provide advance notice in order for
you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information.
If the trouble is causing harm to the telephone network, the telephone company may request you remove the
equipment from the network until the problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must be made by the
manufacturer. Other repair methods may invalidate the FCC registration on this product.
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is
subject to state tariffs.
This equipment is hearing aid compatible.
When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for
the call. Perform such activities in the off-peak hours; such as early morning or late evening.
-26-
WARNING
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary
or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or
failure to warn for a variety of reasons. For example:
•
Intruders may gain access through unprotected openings or have the technical sophistication to
bypass an alarm sensor or disconnect an alarm warning device.
•
Movement detectors (e.g. Passive InfraRed detectors), smoke detectors and many other sensing
devices will not work without power. Battery operated devices will not work without batteries, with dead
batteries, nor if the batteries are not installed properly. Devices powered solely by AC will not work if
their AC power supply is cut off for any reason, however briefly.
•
Signals sent by wireless transmitters may be blocked or reflected before they reach the alarm
receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur
by a reflecting object.
•
A user may not be able to reach a panic or emergency button quickly enough.
•
While smoke detectors have played a key role in reducing residential fire deaths, they may not
activate or provide early warning for a variety of reasons. Some of the reasons smoke detectors used
in conjunction with this System may not work are as follows. Some detectors may have been
improperly installed and positioned. Smoke detectors may not sense fires that start where smoke
cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed
doors. Smoke detectors also may not sense a fire on another level of a residence or building. A
second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke
detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In
general, detectors may not always warn about fires caused by carelessness and safety hazards like
smoking in bed, violent explosions, escaping gas, improper storage of flammable materials,
overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of
the fire and/or the location of the smoke detectors, the detector, even if it operates as anticipated, may
not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
•
Passive InfraRed motion detectors can only detect movement within the designed ranges as
diagrammed in their installation manual. Passive InfraRed detectors do not provide volumetric area
protection. They do create multiple beams of detection, and movement can only be detected in
unobstructed areas covered by those beams. They cannot detect motion or movement that takes
place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.
Mechanical tampering, masking, painting, or spraying of any material on the lenses or any part of the
optical system can reduce or abolish their detection capability. Passive InfraRed detectors sense
changes in temperature; however, as the ambient temperature of the detection area approaches the
temperature of 90° to 105°F (32° to 40°C), the detection performance can decrease or cease.
•
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they
are located on the other side of the closed or partly open doors. If warning devices sound on a
different level of residence from the bedrooms, then they are less likely to waken or alert people inside
the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by a
stereo, radio, air conditioner, or other appliance, or by passing traffic. Finally, alarm warning devices,
however loud, may not warn hearing-impaired people or waken deep sleepers.
•
Telephone lines or other communication media needed to transmit alarm signals from premises to a
central monitoring station may be out of service or temporarily out of service. Telephone and other
communication lines are also subject to compromise by sophisticated intruders.
•
Even if the system responds to the emergency as intended, however, occupants may have insufficient
time to protect themselves from the emergency situation. In the case of a monitored alarm system,
authorities may not respond appropriately.
•
This equipment, like other electrical devices, is subject to component failure. Even though this
equipment is designed to last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate
maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working
properly.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a
substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting
themselves and continue to insure their lives and property.
The producer continues to develop new and improved protection devices. Users of alarm systems owe it to
themselves and their loved ones to learn about these developments.
-27-
ELECTRONICS LINE 3000 Ltd. ONE YEAR LIMITED WARRANTY
Electronics Line 3000 Ltd. (“EL3K”) and its divisions, subsidiaries and affiliates (“Seller”), 2 Granit Street, Kiryat
Arieh Industrial Zone, Petah Tikva 49130 Israel, warrants its security equipment (the “product”) to be free from
defects in materials and workmanship for one year from date of original purchase, under normal use and service.
Batteries are expressly not covered by the warranty. Seller’s obligation is limited to repairing or replacing, at it’s
option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or
workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the
product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact
the security professional who installed and maintains your security equipment or the Seller for product repair.
This one year Limited Warranty is in lieu of all other warranties, obligations or liabilities. THERE ARE NO
WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR
PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO
CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER
BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER’S OWN
NEGLIGENCE OR FAULT.
ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR
UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY
THE SELLER’S OWN NEGLIGENCE OR FAULT.
Some states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, therefore the above limitations or exclusions may not apply to you to that
extent.
Seller does not represent that the product may not be compromised or circumvented; nor that the product will
prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product will in all
cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm
may only reduce the risk of a burglary, robbery, fire, nor other events occurring without providing an alarm, but it is
not insurance nor a guarantee that such will not occur or that there will be no personal injury or property loss as a
result. Neither the Seller nor its directors, officers, shareholders, partners, principles, agents, servants or
employees or their successors, predecessors, assigns, heirs and personal representatives is an insurer nor
guarantor. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR
ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF
THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This
warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. No
increase or alteration, written or verbal, to this warranty is authorized.
-28-
OWNER’S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner’s insurance carrier for possible
premium credit.
A. GENERAL INFORMATION
Insured’s Name and Address:
_____________________________________________________
_____________________________________________________
Insurance Company:
____________________
INFINITI
____________________
Other:
Installed by:
Policy No.:
__________________________
Type of Alarm:
___________________________
Serviced by:
________________________________________
Burglary
________________________
_____________________________________
B. NOTIFIES:
Local Sounding Device
_____________________
Central Station … Name:
_________________________________________________________
Police Dept.:
Address:
_________________________________________________________
Phone:
_________________________________________________________
C. POWERED BY:
AC with rechargeable power supply.
D: TESTING:
… Quarterly
… Monthly
… Weekly
___________________
… Other ______________
E: BURGLARY DETECTING DEVICE LOCATIONS:
… Front Door
st
… 1 Floor Windows
… Basement Door
… Rear Door
… All Windows
… Interior Locations
… All Exterior Doors
… All Accessible Openings (including skylights, air conditioners and vents)
G: ADDITIONAL PERTINENT INFORMATION:
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
Signature:
___________________________________
-29-
Date:
_________________________
ZI0266E (3/06)
PRINTED IN ISRAEL
">