WEATHERPROOF DOME CAMERA Series SPU

WEATHERPROOF DOME CAMERA Series SPU
WEATHERPROOF DOME CAMERA Series
SPU-3750T/3700 User Guide
Before installing and operating the camera, please read this user’s manual carefully.
English
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING
- CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE
THE EQUIPMENT.
CAUTION : To prevent electric shock and risk of fire hazards:
- The installation for this apparatus should be by a qualified service person
and should conform to all local codes.
- Do NOT use power sources other than Class 2 power source.
- Carefully push the unlock buttons to prevent the apparatus falling and
injurying someone.
This installation should be made by a qualified service person and
should conform to all local codes.
Contents
Features……………………………………………………………………………
Cautions for Operating Temperature… …………………………………
Cautions for Using Auto Track(SPU-3750T)… …………………………
Setting Up Auto Track…………………………………………………………
■ Auto Track Using Presets… ………………………………………………
•
•
•
•
6
7
7
8
8
▶ Selecting Auto Track Starting Point 1……………………………………………… 8
▶ Selecting Auto Track Starting Point 2……………………………………………… 9
▶ Setting Auto Tracking Details………………………………………………………… 9
▶ Starting Auto Track (Loading Presets)………………………………………………11
▶ Auto Tracking Using Group Command………………………………………………11
■ Auto Tracking Using Target Lock… …………………………………… 13
• Warnings & Cautions… ……………………………………………………… 14
• Components and Accessories……………………………………………… 18
• Component Names and Functions………………………………………… 19
• Installing Your Camera………………………………………………………… 21
■ Speed Dome Camara and Appliances Wiring Diagram………… 21
■ How to Set Up Protocols and ID DIP Switches………………… 23
■ Communication DIP Switch Settings (SW2)………………………… 24
▶ Protocol Settings……………………………………………………………………… 24
▶ Baud Rate Settings…………………………………………………………………… 25
▶ Communication Method Settings………………………………………………… 25
▶ Communication Response Settings……………………………………………… 25
▶ Termination Settings………………………………………………………………… 25
▶ Camera Backup Settings…………………………………………………………… 26
■ Camera ID DIP Switch Settings(SW1)………………………………… 26
▶ Camera ID Chart……………………………………………………………………… 27
■ Preparing Adapter and Cables… ……………………………………… 33
■ Installation Suggestions for Bracket Types………………………… 35
■ On-wall Mount Type Installation Example… ……………………… 37
• Interface Symbols……………………………………………………………… 41
• Operating Your Camera……………………………………………………… 42
• Functional Description………………………………………………………… 46
SPEED DOME CAMERA
4
User Guide
■ Camera Setting……………………………………………………………… 46
▶ Focus and Zoom Settings…………………………………………………………… 46
▶ White Balance………………………………………………………………………… 48
▶ Exposure………………………………………………………………………………… 49
▶ Backlight………………………………………………………………………………… 50
▶ AGC……………………………………………………………………………………… 54
▶ SSNR(Samsung Super Noise Reduction)… …………………………………… 55
▶ Day & Night… ………………………………………………………………………… 56
▶ Others…………………………………………………………………………………… 57
■ Sequence Setting…………………………………………………………… 58
▶ Power On Resume & MD Dwell Time …………………………………………… 58
▶ Preset …………………………………………………………………………………… 59
▶ Swing SEQ……………………………………………………………………………… 63
▶ Group SEQ……………………………………………………………………………… 64
▶ Tour SEQ………………………………………………………………………………… 65
▶ PTZ Trace… …………………………………………………………………………… 66
▶ Auto Run………………………………………………………………………………… 67
■ P/T Setting…………………………………………………………………… 68
▶ Pan/Tilt Limit…………………………………………………………………………… 68
▶ Area Setting…………………………………………………………………………… 69
▶ Area Masking… ……………………………………………………………………… 70
▶ Prop. P/T………………………………………………………………………………… 71
▶ Digital Flip……………………………………………………………………………… 72
▶ Image Holding………………………………………………………………………… 73
▶ Auto Track 1 (SPU-3750T Only)…………………………………………………… 74
▶ Auto Track 2 (SPU-3750T Only)…………………………………………………… 76
■ OSD Setting…………………………………………………………………… 78
■ Alarm Setting………………………………………………………………… 79
■ Initialize………………………………………………………………………… 83
■ Status…………………………………………………………………………… 85
• Troubleshooting………………………………………………………………… 86
• Product Specification… ……………………………………………………… 91
SPEED DOME CAMERA
5
User Guide
Features
Cautions for Operating Temperature
Smart P/T
A/F 37x Optical Zoom
The built-in 37x optical zoom lens with auto-focus is
combined with a 12x digital zoom, providing a
maximum of 444x zoom.
The Smart P/T function automatically adjusts the
control speed of the Pan and Tilt functions according
to the current zoom ratio. It is useful to adjust the
functions manually for detailed controls when
monitoring at high zoom ratios.
Versatile protocols and coaxial
communication
Day & Night
RS-422/485, Coaxial communication methods are
supported.
- R S-422/485 (10 species) : Samsung Techwin, Pelco (D / P),
Samsung Electronics, Panasonic, Honeywell, AD, Vicon,
GE, BOSCH
- Coaxial Communications : Pelco Coaxitron (automatic
detection)
With its daytime & nighttime switch and Sens-Up
functions based on the ICR (Infrared Cut filter Removal)
method, the camera provides high quality pictures
regardless of whether it is day or night.
*Sens-Up increases the CCD sensitivity by electrically
extending the camera’s exposure time.
* Day & Night enables you to select between color and
B/W modes depending on the lighting conditions.
Wide Range Auto Security
Functions
- Auto Tracking(SPU-3750T Only) : A moving object or a person
can be tracked and recorded automatically by the camera
with its Pan, Tilt, and Zoom functions.
- Multiple Preset Function Saving : Up to 13 camera image
properities can be saved individually to provide high quality
pictures.
- Image Holding : When moving between presets in Group and
Tour functions, using this Preset Freeze function holds the
image status and helps the screen observer relieve visual
fatigue.
- P TZ Trace : Patterns operated with the joystick can be saved
and replayed by users.
- S wing : Using the Swing function commands the camera to
move between 2 selected locations, monitoring the route.
- G roup Search : Maximum 255 Preset positions are toured in
order.
- Tour Search : Maximum 6 Group Search functions are toured
in order.
Highly durable built-in housing
This IP66-rated built-in housing is easy to install, and
protects the product from a full range of harsh outdoor
conditions. The high performance built-in fan/heater
enables the product to operate under extreme
temperatures between -50℃ ~ 50℃ .
Preset Position Saving and Loading
Up to 255 preset positions can be set. Using this
function saves and brings up the camera feed of a
selected monitoring location.
Camera Backup
This is to back up the camera’s sequence information
and presets. This is useful when the camera or its
install base are damaged or malfunctions occur.
Digital Flip
The Digital Flip function is useful to monitor moving objects
or people passing directly under the camera. When an object
or a person passes directly under the camera, its tilt motor
follows the object or person over 100 degrees to the other
side of the tilt area without panning. The screen inversion
starts to occur at 100 degrees or higher is digitally adjusted.
SPEED DOME CAMERA
Area Masking
If a monitoring location includes a highly private area,
the area can be selectively masked on the screen.
6
User Guide
1. The camera cannot operate properly at temperatures lower than -50℃.
2. E ven if the surrounding temperature is -50℃ or higher, the camera may not thaw itself and operate properly
depending on the installation environment.
3. Always keep the power on, so the camera can maintain its internal temperature at -10℃ or higher.
4. If the camera was turned on after being left at temperatures lower than -50℃ for a long duration:
- If the internal temperature is lower than -20℃, the camera does not transmit video signals and displays a
black screen along with the "Wait to warm up(xx Left)" message, instead of operating properly.
- If the internal temperature is higher than -20℃ and lower than -10℃, the "Wait to warm up(xx Left)"
message disappears as the camera resets itself and enters the operation mode.
However, only manual P/T operation is in effect while the Sequence and Turbo commands are limited in use.
- If the internal temperature is higher than -10℃, the camera activates all Sequence and Turbo commands.
5. If the heater malfunctions, a message appears as follows.
- "Please Check Heater System"
- If this message appears, turn off the camera and call where you bought.
Cautions for Using Auto Track(SPU-3750T)
The following cautions are for the Auto Track function built-in with the SPU-3750T; The SPU-3700 does not have
Auto Track.
To use Auto Track to its full potential, please read and be aware of the following cautions. Neglecting the cautions
may cause unsatisfactory performance of the tracking function as well as camera malfunctions.
• Auto Track is specifically to track down unknown intruders. It is not be suitable to monitor a crowd.
• If the camera is not safely secured, tracking errors may occur.
• If the camera lens is smeared with foreign substances, snow flakes, or raindrops, the camera may incur
unsatisfactory performance in the tracking function. For optimal performance, please install the camera in an
environment safe from contamination, and clean the camera lens on regular basis.
• If the tracking function shows poor performance at nighttime or under low light circumstances, use the Sens-Up
function.
• Auto Track may have errors at times when pronounced shadows are created: e.g. sunrise and sunset.
• The camera may catch and follow unintended movements – car traffic or swaying tree branches – during the
Auto Track operation. To prevent and correct such errors, adjust the installation direction and angle of the camera,
or use Zone Settings (Mask) (page 70).
• Adjust the installation direction and angle of the camera, or use Zone Settings also under the following
conditions: With excessively bright light sources, under flickering lights, or if the camera displays internal
reflections.
• When using Auto Track, it is recommended to adjust the tracking object size to 1/4 of the screen.
• This feature may not perform as expected depending on the situation and circumstances. Samsung Techwin is
not responsible for injuries and financial damage caused by the situation described above.
SPEED DOME CAMERA
7
User Guide
Setting Up Auto Track
• Two different Auto Track setup methods are available.
Using Presets
- Select a starting point for Auto Track as a preset to activate Auto Tracking.
(This can be used in conjunction with Group SEQ and Tour SEQ.)
Using Target Lock
- Select an object on the screen to activate Auto Tracking.
2. Selecting Auto Track Starting Point 2
▶ Main Menu/Sequence Settings/Preset/Edit
Preset Edit
Preset = 001*
(1~255)
✽ The selected preset is indicated with an asterisk (*).
Auto Track Using Presets
Preset
Settings
Auto
Tracking
Editing
Presets
· Set a Preset to Start
Auto Tracking
· Set Zoom/Focus
· Select Tracking Mode
for a Preset
· Tracking On
· S et Auto Tracking
details
Preset Edit
[001]
271/045/1X
ONE SHOT AF
050
AUTO
⑧
PTZ
Focus Mode
Brightness
Iris
Back Light
Day & Night
After Act.
Scene Adj.
At Menu 7 [After Act.], select [TRACK].
- TRACK : Perform Auto Track upon arrival.
B/W
OFF
Preset Edit
<Auto Track Setting Flow Chart>
At Preset Edit, select the preset number under
the Preset Settings menu.
Preset = 001T (1~255)
When the [After Act.] menu is set to [TRACK], the
letter “T” appears next to the preset number as
shown in the figure.
1. Selecting Auto Track Starting Point 1
▶ Main Menu/Sequence Settings/Preset/Settings
Preset Setting
Preset = 001
(255)
3. Setting Auto Tracking Details
Using the joystick, select a preset number from 1
to 255, and then press [Enter].
▶ Main Menu/P/T Settings/Auto Track1
Auto Track 1
Preset Setting Z>Z00M
Select the preset as the starting point for Auto
Track. Using the joystick, set the Pan/Tilt and
Zoom/Focus options.
1+PST:ZOOM 2+PST:FOCUS
Use W/T Preset
SPEED DOME CAMERA
8
User Guide
Auto Track
Camera Height
Object Size
Sensitivity
Zoom Control
Auto Release
Auto Return
Lost Mode OFF
02.5M
SMALL
HIGH
OFF
OFF
OFF
STOP
At Menu 1 [Auto Track], select [ON] to activate
Auto Tracking.
Set the Camera Height, Object Size, Sensitivity,
and Zoom Control options.
Refer to the timing chart below to set the [Auto
Release], [Auto Return], and [Lost Mode] options.
SPEED DOME CAMERA
9
User Guide
Setting Up Auto Track
[ Auto Release ]
(10sec ~ 5min)
[ Auto Return ]
(1sec ~ 5min)
4. Starting Auto Track (Loading Presets)
▶ Main Menu/Sequence Settings/Preset
Preset
Start
Tracking
[ Lost Mode ]
Performed only for the
Auto Release duration
Finish
Tracking
Initial
Location
<Auto Track Timing Chart>
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Preset Edit
Auto Release : C
ommand the camera to follow an object for a set duration and
then return to its initial (preset) location.
Auto Return : A
fter Auto Release expires, command the camera to stand by at
the tracking finish point and then return to its initial location.
(Selecting OFF keeps the camera at the tracking finish point
instead of returning it to the initial location.)
Lost Mode : S et an action for the camera when it loses its tracking object.
(Performed only for the Auto Release duration.)
- STOP : Stop at the lost point and abort tracking.
- RESEARCH : Stop at the lost point and search for a new object.
- ZOOM-OUT : When an object is lost, Zoom Out to find and track a new object.
SPEED DOME CAMERA
10 User Guide
Preset = 001T (1~255)
Start Auto Tracking in the OSD Menu
① Select [Execute].
② Select a Preset to start Auto Tracking.
③ The camera will move to the Preset location
and start Auto Tracking.
Start Auto Tracking Using the Controller
① Exit the OSD menu then press a Preset
number on the controller keypad to start Auto
Tracking. And Press a <Preset> button.(The
number can be checked on the LCD window.)
② The camera will move to the Preset location
and start Auto Tracking.
5. Auto Tracking Using Group Command
▶ Main Menu/Sequence Settings/Group SEQ/Group X/Settings
Group SEQ 1
NO
001:
002:
003:
004:
005:
006:
007:
PSET DWT(s) SPD
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
PSET : Using the joystick, enter a preset number
under which [After Act.] menu is set to
[TRACK].
DWT : Indicates the camera time spent at each
preset location. (1 ~ 120sec)
SPD : Adjusts the camera movement speed by 64
different levels.
SPEED DOME CAMERA
11 User Guide
Setting Up Auto Track
After finishing setup, press [Execute] in the parent menu to activate the Group
SEQ mode. (Or turn OFF OSD Menu, and then press [Group]+[Group Number]
using the controller.)
Auto Tracking Using Target Lock
1. Setting Target Lock
▶ Main Menu/P/T Settings/Auto Track2
Auto Track 2
[Preset 1]
[Preset 2]
[Preset N]
[Auto Release]
(10sec~5min)
Start
Group SEQ
Start
Tracking
[ Lost Mode ]
Performed only for the Auto
Release Duration
Last
Preset
Finish
Tracking
[ Auto Return ]
(1sec~5min)
Next
Preset
① Zone Setting
Indicator
Target Lock
When Group SEQ is activated, the camera starts auto tracking at the [Preset 1]
location. For the set DWT duration, the camera performs Auto Track according
to [Auto Release] and [Auto Return] settings. If no movement is detected, it
moves to [Preset 2] and repeats the procedures.
SPEED DOME CAMERA
12 User Guide
Target Lock => [ON]
- When Target Lock is turned [ON], a red box
appears in the center of the screen.
Using the joystick, move the red box to encircle
an object and then press [Enter] to start Auto
Tracking the object.
OFF
OFF
2. Target Lock
<Group SEQ Timing Chart>
P:234 T:5 1x
SPEED DOME CAMERA
13 User Guide
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Warnings & Cautions
Warnings & Cautions
Warnings
Stop using the camera if smoke or
abnormal heat is detected.
Do not install on your own.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Unplug the power plug during a thunder storm to prevent fire and damage to the product.
* This product is support equipment for a security system. Therefore, we can't compensate for material losses and/or
personal injuries by robbery, fire, natural disaster, or anything of the sort.
Warning/Caution/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries, including
death.
Ignoring this information may
result in material loss and/or slight
injuries.
Indicates “Prohibited”.
Indicates “No Disassembly”.
This installation should be made by a qualified service
person. Installing this product on your own may result in
fire or electric shock. For the installation service, contact
the retail shop where you bought the product.
May cause fire.
Do not install in high humidity or in a
place that may be exposed to oil or gas.
May cause product malfunctions, electric shocks, and fire.
Do not install on an unsubstantial wall
that may be subject to vibrations.
May cause the product to fall.
Do not handle the power plug
with wet hands.
May cause electric shock.
SPEED DOME CAMERA
14 User Guide
Do not disassemble the camera or
insert foreign subjects.
May cause fire and damage to the product.
SPEED DOME CAMERA
15 User Guide
Warnings & Cautions
Warnings & Cautions
Detailed Warnings and Cautions
Cautions
Do not install under extreme
temperature conditions.
Do not install under unstable
lighting conditions.
Only use in the temperature range of between -50ºC and
+50ºC to prevent low graphics quality and product
malfunction. When using in high temperature conditions,
provide good ventilation.
Severe lighting changes or flickering may hinder normal
camera operation.
Do not drop the camera or subject
it to physical shock.
Never keep the camera facing direct
sunlight or any other strong lights.
May cause product malfunctions.
May cause critical damage to the CCD.
Avoid touching the camera lens.
Do not touch the heater when the
product is in operation.
- Avoid operating the camera for long durations under high temperatures and in high humidity. Excessive
heat can shorten the lifespan of the camera components.
- D o not install or place the camera near any heat sources.
- S ubjecting the dome cover to physical shock may damage the camera and cause water leakage into it.
- D o not place the camera facing direct sunlight or other intense light sources. Strong lights such as
spotlights can cause distortions—blooming and smear—as well as discolorations on the screen by
heating up the color filter of the camera. They also may cause internal reflections of the camera, leading to
operational malfunctions.
- D o not drop the camera or subject it to physical shock or vibration; this can cause serious damage to the
camera.
- When installing the camera near a power line, make sure to keep at least 1 meter distance from the power
line, or earth an additional metal pipe to separate the camera from the power source.
- Install this camera on the ceiling. Installing it on the ground or a unleveled location may cause product
malfunctions and shorten its lifespan.
- Avoid installing and operating the camera in the following places.
∙ P laces whose temperature exceed the camera’s recommended range. ( -50℃ ~ 50℃)
∙ P laces where drastic temperature changes occur: e.g. Near an air conditioner.
∙ P laces that are exposed to steam, oil, and inflammable substances: e.g. Inside a kitchen.
∙ P laces that are exposed to radioactivity, X-rays, strong electric waves, and electro-magnetic waves.
∙ P laces that are exposed to outdoor air contaminants: e.g. Dust and car exhaust.
∙ P laces in high humidity.
∙ P laces that are exposed to corrosive gas: e.g. Next to the sea.
- S meared and dusty dome covers decrease the picture and video quality. Clean the dome cover and camera
lens on a regular basis.
- R emove the plastic wrap on the dome cover only after the camera installation is complete.
- This camera is not equipped with a power switch. Plug in the camera only after the installation is complete.
Expendable components
The lens is the most important component of the camera.
Be careful not to smear it with fingerprints.
SPEED DOME CAMERA
The heater makes high temperature.
16 User Guide
The following expendable components should be replaced within the recommended lifetime. Lifetimes vary
somewhat and depend on the operating environments and conditions.
- Cooling fan: Approx. 50,000 hours
- Slipring: Approx. 20,000 hours
- VCL lens: Approx. 20,000 hours
SPEED DOME CAMERA
17 User Guide
Component Names and Functions
Components and Accessories
* Components
Body
Front
Power Adapter (AC 24V, Peak 2.5A)
Hexa Wrench
Back
User’s Manual
1
* The set for America does not include the power adapter.
* Accessories
The following items are sold separately from the camera.
Brackets
STB-300PW Wall Bracket
STB-300PP Ceiling Mount
STB-355PPM Parapet Mount
Bottom
2
STB-270B Setup Box
STB-340PCM Corner Mount
3
1 Safety Wire Holder
2 SW2: Communication DIP Switch
3 SW1: ID DIP Switch
STB-330PPM Pole Mount
Notes
• For the DIP switch settings, please refer to the “Installing Your Camera” on Page 23~32.
STB-40PF Pendent Coupling
* Ceiling bracket (STB-300PP) pipe not provided
SPEED DOME CAMERA
18 User Guide
SPEED DOME CAMERA
19 User Guide
Installing Your Camera
Component Names and Functions
Camera Wiring Interface Board (Sold Separately)
Speed Dome Camera and Appliances Wiring Diagram
For the camera wiring, please refer to the picture below.
The camera's wiring interface board is fitted to the housing, this is sold separately.(When
using coaxial communication, a separate control signal connection is not required.)
Alarm
Connecting with Samsung Techwin’s “Stand Alone DVR”
·RS-485 :
Camera
D+
DAlarm Output
Communications and AUX
T(TX)+
T(TX)-
SVR-1680/1660/1645/960/
·RS-422 :
Camera
Alarm Input
Stand Alone DVR
Stand Alone DVR
D+
D-
T(TX)+
T(TX)-
TXD+
TXD-
R(RX)+
R(TX)-
SVR-945
Power Supply
SVR-940/450
SVR-1650/1640A/950E
Connecting with the Samsung Techwin Controller SCC-3100A
AC24V 2.5A
Power Input
Ground
Refer to the below Control
Signal Connection chart
Camera
AUX Output
·RS485 Communications
Camera
D+
D-
·RS422 Communications
Camera
D+
DTXD+
TXD-
Controller
or DVR
TXD+
TXD-
Controller
or DVR
TXD+
TXDRXD+
RXD-
SPEED DOME CAMERA
D+
D-
20 User Guide
RX+
RXTX+
TX-
Notes
• The maximum power capacity of the built-in
relay is 30VDC/2A, 125VAC/0.5A, and
250VAC/0.25A.
• Connecting the power connector and GND
incorrectly to the NC/NO and COM ports may
cause a short circuit and fire, damaging the
camera.
SCC-3100A
Data Box PORT1
·RS-422 :
Camera
SCC-3100A
Data Box PORT1
TX+
TX-
RX+
RX-
D+
D-
TX+
TX-
SPEED DOME CAMERA
21 User Guide
SCC-3100A Data Box
Control Signal Connection
·RS-485 :
Installing Your Camera
Note!
* DVRs that can fully control a PTZ Dome via RS-422/485 are as follows
- 32Ch : SVR-3200
- 16Ch : SVR-1680/1660/1645/1650E/1640A
- 9Ch : SVR-960/945/950E
- 4Ch : SVR-440
* Samsung Techwin DVR products that can fully control a PTZ Dome via coaxial are as
follows
- 16Ch : SVR-1680C,SVR-1660C
- 9Ch : SVR-960C
* The following DVR models support only the Pan, Tilt, Zoom, and Focus functions of
the camera.
- 9Ch : SVR-940
- 4Ch : SVR-450,SVR-470
* Memo
Installing Your Camera
How to Set Up Protocols and ID DIP Switches
You can control various settings of the camera system using the Communication and ID
DIP switches. Before installing the product, please set up the DIP switches according to
the installation environment.
1. Detach the camera frame from the install base, and place the bottom of the frame
toward you as shown in the picture below.
2. Set the switches according to your installation environment. For more detailed setup
information, please refer to the chart on the next page.
3. The camera may malfunction if the switches are not fully turned On/Off; please
double check the switches before finishing setup.
Communication Protocol DIP Switch(SW2)
MEMO
Camera ID DIP Switch(SW1)
SPEED DOME CAMERA
22 User Guide
SPEED DOME CAMERA
23 User Guide
Installing Your Camera
Installing Your Camera
Communication Protocol DIP Switch Settings (SW2)
*Coaxial communication automatically detects signals, and so does not require a separate
communication setup process.
ON
ON
• Baud Rate Settings
Select the transfer speed of a selected communication protocol.
No.
1
2
3
4
Baud Rate(BPS)
2,400
4,800
9,600
19,200
SW2-#5
ON
ON
OFF
OFF
SW2-#6
ON
OFF
OFF
ON
OFF
SW2
SW2 Pin No.
1~4
5~6
7
8
9
10~11
12
Purpose
Protocol Settings
Baud Rate Settings
Transfer Method (RS-485/422) Settings
Response Mode Settings
Backup Mode Settings 1
Termination Settings
Backup Mode Settings 2
• Communication Method Settings
Select a communication method for the camera.
SW2- #7
OFF
RS-485(2Wire)
Select a communication response method for the camera and controller: Response or No
Response.
Select a communication protocol for the camera
Protocol
Samsung Techwin
Pelco-D
Pelco-P
Samsung Elec.
Panasonic
Vicon
Honeywell
AD
GE
BOSCH
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ON
RS-422(4Wire)
• Communication Response Settings
• Protocol Settings
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Function
Transfer Mode Switch
SW2-#1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
SPEED DOME CAMERA
SW2-#2
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
24 User Guide
SW2-#3
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW2-#4
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW2- #8
Function
Response Mode Switch
ON
Response
OFF
No Response
• Termination Settings
To prevent the attenuation of communication signals between the camera and controller,
the items at the end of line must be set up with the termination settings.
Camera Input Position
Termination of Longest Path
On the Path
SW2- #10
ON
OFF
SW2- #11
ON
OFF
*This model is provided with factory defaults of all DIP switches set to OFF. The default
settings are shaded in the table.
SPEED DOME CAMERA
25 User Guide
Installing Your Camera
Installing Your Camera
• Camera ID Chart
• Camera Backup Settings
These settings are useful when the camera or its install base are damaged or malfunctions
occur. When replacing the camera or its install base, you can transfer existing presets and
sequence information to the replacement using these settings.
Backup Function
Backup(IB→D)
Backup(D→IB)
Backup Disable
SW2- #9
OFF
ON
-
SW2- #12
OFF
OFF
ON
- Backup(IB→D) : Enables transferring the current camera's sequence information to a new
camera.
- Backup(D→IB) : Enables transferring the current camera's sequence information to a new
install base.
*IB: Install base, D: Dome Camera
Notes
• To use a third party controller with this product, please contact our After-Sales Service or
Technology Department.
• AD Protocol Control Method
- Input Camera OSD: 3+Auxiliary On
- Output Camera OSD: 3+Auxiliary Off
- Enter: IRIS Open
- ESC: IRIS Close
• For more information about the protocols, refer to our official website.
Camera ID DIP Switch Settings (SW1)
To set up camera IDs, refer to the “Camera ID Chart” next.
ON
ON
OFF
SW1
SPEED DOME CAMERA
26 User Guide
ID
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
SW1-#1
ON/OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW1-#3
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
SW1-#4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SPEED DOME CAMERA
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
27 User Guide
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Installing Your Camera
ID
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW1-#2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW1-#3
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
SW1-#4
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
SPEED DOME CAMERA
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
28 User Guide
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Installing Your Camera
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ID
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
SW1-#1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW1-#3
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
SW1-#4
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#5
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SPEED DOME CAMERA
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
29 User Guide
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Installing Your Camera
ID
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW1-#2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
SW1-#3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
SW1-#4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
SPEED DOME CAMERA
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
30 User Guide
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Installing Your Camera
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ID
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
SW1-#1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW1-#3
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
SW1-#4
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#5
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
SPEED DOME CAMERA
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
31 User Guide
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Installing Your Camera
ID
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW1-#3
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
SW1-#4
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
SPEED DOME CAMERA
SW1-#5
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
32 User Guide
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Installing Your Camera
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Preparing Adapter and Cables
– Power Adapter
Power adapter has the capacity of AC24V 2.5A.
– Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
Distance
300m
450m
600m
Recommended Cable Specification
4C2V(RG-59/U)
5C2V(RG-6/U)
7C2V(RG-11/U)
Notes
• If the camera is controlled through coaxial communication, please use a video amp
intended for coaxial communications. Regular video amps do not transfer coaxial signals.
– Communications Cable
For the camera to communicate with the controller, a
RS-485/422 communications line is required. To ensure
the quality of long distance communication and the
accuracy of the overall communication it is
recommended using a twisted pair cable such as UTP.
* Caution!
Depending on the camera’s environment, the communications distance may vary.
Notes
• Neither the video nor communications cable is enclosed with the camera.
it is recommended that pure copper coax cable is used and not copper coated steel, as
this will cause issues with the communication over the coaxial cable.”
* Neither the video nor communications cable is enclosed with the camera.
SPEED DOME CAMERA
33 User Guide
Installing Your Camera
Installing Your Camera
Installation Suggestions for Bracket Types
• Camera Wiring Diagram
To install the camera on a wall or ceiling, please purchase and use an extra wall mount:
STB-300PW for walls, STB-300PP for ceilings or STB-355PPM for parapet
For more detailed instructions, please refer to the bracket’s user manual.
RS-422/485
SVR Series
1
2
...
16
RS-422/485
SVR Series
1
2
...
16
Coaxial
Communication
SVR Series
1
2
...
16
Coaxial
Communication
SVR Series
1
2
...
16
SCC-3100A
CONTROLLER (SUB)
SCC-3100A
CONTROLLER (MAIN)
SPEED DOME CAMERA
34 User Guide
CONTROL LINE
VIDEO LINE
CONTROL/VIDEO LINE
Wall Bracket (STB-300PW)
SPEED DOME CAMERA
Ceiling Mount (STB-300PP)
35 User Guide
Installing Your Camera
Installing Your Camera
On-wall Mount Type Installation Example
Notes
• Do not connect the camera to a power outlet until the installation is complete. Supplying
power in the middle of the installation may cause fire or damage the product.
• How to Set Up Install Base
1. Open Hinged Door
As shown in the picture below, gently
press and lift up the handle of the
hinged door on the bottom of the
install base.
2. Connect Terminal Wires
Connect each wire to the pertinent
terminal block.
For more detailed instructions, please
refer to the “Camera Wiring Diagram”
on Page 20.
Once all the wires are connected, close
the hinged door.
Parapet Mount (STB-355PPM)
Setup Box (STB-270B)
Knob
Control Line
Power Line
Video Out Line
Notes
• Make sure to first hook the camera's safety cable to the mount before proceeding.
Otherwise you may be exposed to serious injury caused by a fallen camera.
SPEED DOME CAMERA
36 User Guide
SPEED DOME CAMERA
37 User Guide
Installing Your Camera
Installing Your Camera
• Secure Install Base to Bracket
• Attach Camera
1. Assemble Bracket and Install Base
Assemble the install base and bracket
following the screw directions.
Make sure to keep the installation
direction guide at the front.
1. Assemble Camera and Install Base
Assemble the install base and camera
by matching the installation direction
guides.
Arrow
2. Attach Camera
Turn the camera frame
counterclockwise until the protrusions
on the camera frame and install base
become matched perfectly.
2. Secure Bracket and Install Base
Using 2 hexagon screws, secure the
assembled bracket and install base.
SPEED DOME CAMERA
38 User Guide
SPEED DOME CAMERA
39 User Guide
Installing Your Camera
• Secure Camera and Attach Safety Cable
1. Secure Camera and Install Base
As shown in the picture below, secure
the install base and camera using 3
hexagon screws.
2. Connect Safety Cable
Hook the safety cable on the back of
the camera to the loop on the bracket.
Interface Symbols
• Motion Detection Standby/Operation Display :
- When in standby mode, the " " in the upper right of the screen blinks and then
changes to " " if motion is detected.
• Alarm Input Port Status Display :
- "①","②" and "③" in the upper right of the screen blink.
• Current Alarm Port Display According to Input Alarm Ports(Priority) :
- Only one of " "," "," " in the upper right of the screen blinks.
• Preset Number Display Settings :
- '*' : If a preset number is already available
- 'H' : If a preset location is the camera’s home position
- 'T' : If a preset location is the camera’s Auto Track starting point(SPU-3750T Only)
• If an OSD Menu has Sub Menus :
- The color of the circle around the menu number shows as embossed, e.g. "①".
• If an OSD Menu Does Not Have Sub Menus :
- The circle around the menu number shows as engraved, e.g. "".
Motion Detect
Alarm Input
• PTZ Function Screen :
Area Display
Sequence Status
Preset Info
ID=001
①②③
Area1 Area Name
G-SEQ1
PRESET=001 Preset Name
P:300 T:040 10X
• Preset Number Setting Screen :
SPEED DOME CAMERA
40 User Guide
Preset Edit
Preset=011* (1~255)
SPEED DOME CAMERA
41 User Guide
Operating Your Camera
Operating Your Camera
*OSD Menu Chart
• OSD Menu Screen :
P1
Sub Menu Available
Sub Menu Not Available
Camera Setting
① Focus & Zoom
White Balance
-- ---
P2
①Focus
&Zoom
②Zoom Tracking
③Digital Zoom
ATW
②White
Balance
AWB Mode
①Brightness
Operating Your Camera
②Iris
• Panning and Tilting
- Use the joystick of the controller or its direction buttons.
• Controlling Zoom
- Move the joystick clockwise (Tele) or counterclockwise (Wide), or use the zoom
buttons.
• Accessing Screen Menus
- Press the Menu or OSD button on the controller.
✽ For more detailed information about controls using a third party controller or a DVR, refer to the
user’s manual of the product.
OSD Commands, Function Chart, and Menu Controls
This dome camera can be operated using two methods: Using hot keys on its dedicated
controller, or accessing the OSD (On Screen Display) on the video output. The OSD menu
commands are as follows:
Command
Move the joystick up/down/left/right
Enter/Focus Far
ESC/Focus Near
P3
①Focus Mode
Function
Moves the OSD menus up/down/left/right, respectively.
Selects a menu and allows access to the sub menus.
Cancels a command and moves back to an upper-level menu.
③Exposure
④Sens-Up
①Off
①Camera
Setting
④Back Light
⑤AGC
⑥SSNR
⑦Day&Night
①Preset
42 User Guide
Limit
Low/Medium/High
Level
1~100
Level
Low/High
③HLC
Mask Color
0~10
Up/Down/Left/Right/
④BLC
Increase/Decrease
Off/Low/Medium/High
Manual
Level
5~41
Off/Low/Medium/High
Auto
Burst Level
Mode
Color
0~100
B/W
Burst On/Off
Duration
Slow/Fast
Dwell Time
5/7/10/15/20/30/40/60 Sec
Internal
Sync
Line Lock
Line Lock Phase
Stabilizer
On/Off
①Sharpness On(0~32)/Off
Image Adj.
②Color
0~100
Freeze
On/Off
①Setting②Edit③Home Position④Execute⑤Clear
⑥Status
②WDR
⑧Others
SPEED DOME CAMERA
③Shutter
P4
P5
Auto/Manual/One Shot AF
Mode
Auto/Tracking/Off
Speed
Slow/Medium/Fast
Off/2X/3X/4X/5X/.../12X
ATW/INDOOR/OUTDOOR/AWC
Red
Manual
Blue
0~100
Auto
Manual
Iris Level
---/A.FLK/Manual
Sens-Up Limit
Auto/Off
X2/X4...X256
SPEED DOME CAMERA
43 User Guide
Default
One Shot AF
Auto
Fast
Off
ATW
117
93
50
Auto
F1.6
--Auto(X2)
Off
Medium
50
Low
5
Medium
5 dB
Medium
Color
Fast
5 Sec
Internal
Off
20
50
Off
Operating Your Camera
①Pan Swing
①Setting②Execute③Clear
②Swing SEQ. ②Tilt Swing
①Setting②Execute③Clear
③P&T Swing
①Setting②Execute③Clear
③Group SEQ. Group1~6
①Setting②Execute③Clear
④Tour SEQ.
①Setting②Execute③Clear
⑤PTZ Trace
①Replay②Memorize
Trace1~4
②Sequence
Off/Home/Preset/Swing/Group/Tour/
Setting
①Mode
Trace/A.Pan
⑥Auto Run
②Time
1~60(Sec), 1~60(Min)
⑦Power On
On/Off
Resume
①Off
⑧MD Dwell
Time
②On
1~60(Sec),1~60(Min)
①Position
①Pan Limit
②On/Off
①Pan/Tilt Limit
①Position
②Tilt Limit
②On/Off
②Area Setting Area1~8
①Name/②Position/③On/Off
③Area Masking Mask1~8
①Position/②On/Off
④Prop.P/T
On/Off
⑤Digital Flip
On/Off
⑥Image Hold
③P/T
Setting
On/Off
①Auto Track
②Camera Height
③Object Size
④Sensitivity
⑦Auto Track 1
⑤Zoom Control
⑥Auto Release
⑦Auto Return
⑧Lost Mode
①Zone Setting
⑧Auto Track 2
①Camera ID
②Indicator
③Target Lock
On/Off
SPEED DOME CAMERA
Operating Your Camera
②Camera
Name
③Preset
Number
④OSD
Setting
Off
30 Sec
On
44 User Guide
⑤Sequence
Status
⑥Area Name
⑦PTZ Position
⑧Language
①Alarm Enable
30 Sec
②Alarm Input
Off
Off
Off
Off
On
On
Off
2.5 m
Small
High
Off
Off
Off
Stop
Mask
Off
Off
Off
On
Off
On/Off
On
①On/Off
②Edit
Off
On/Off
On
On/Off
On/Off
English/Chinese/Français/Deutsch/Español/Italiano
On/Off
Off
On
English
Off
MOD:NC/NO/OFF
Priority:1~3
SEQ:Preset/Swing/Group/Tour/
A.Pan/Trace/Off
①In1
Out
③Alarm Output
④Aux. Output
⑥Initialize
②In2
③In3
⑤Alarm
Setting
Off
On/Off
2.5m~30m
Small/Medium/Large
High/Medium/Low
Off/One Shot/Continuous
Off/10sec~5min
Off/1sec~5min
Stop/Research/Zoom Out
①Position
②Mode(Alarm/Mask)
Zone1~8
③On/Off
Off/On/Pointer/Target
On/Off
④Preset Name
①On/Off
②Edit
①Power On
Reset
②Factory
Default Set
③Camera
Default Set
④Auto Refresh
⑤Auto Track
Default
⑥Fan Life
Time
①On/Off
②Time
Off
1~3,MD,TRK
Off/On/Momentary
Off
1~60(Sec), 1~60(Min),
Dwell Time
1~60(Hour)
On/Off
Off
1~60(Sec), 1~60(Min)
Cancel/Execute
Cancel/Execute
Cancel/Execute
Off,1~7Days
Off
Cancel/Execute
①Message Display On/Off
②Message Clear
Cancel/Execute
③Time Reset
④Time Remain(hour)
⑦Status
SPEED DOME CAMERA
45 User Guide
On
49000
Functional Description
Functional Description
1.2 Zoom Tracking
▶ Main Menu/Camera Setting/Focus & Zoom/Zoom Tracking
Camera Setting
1. Focus and Zoom Settings
1.1 Focus Mode and Digital Zoom Setting Menu
▶ Main Menu/Camera Setting/Focus & Zoom
Focus Mode :
- Auto : Performs continuous auto-focus.
- Manual : Changes the camera mode to Manual Focus.
- One Shot AF : Auto-focuses the camera once after the
Pan, Tilt, or Zoom function is used.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Digital Zoom :
Enables the maximum digital zoom.
Setting the digital zoom to 12x provides a total zoom of
444x.
➡
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
➡
Focus & Zoom
Focus Mode ONE SHOT AF
② Zoom Tracking
③ Digital Zoom OFF
Notes
• Unlike the optical zoom, the graphics quality of the
digital zoom decreases as its zoom ratio increases.
• The auto-focus function may not operate normally
under the following conditions :
- When background illumination is low
- While Slow-Shutter is in operation
- If the zoom level is set too high
- When background illumination is too high
- If a long distance object and a close distance object
appear together within a monitoring area
- If there is no contrast, e.g. the sky or a wall
- If the camera is facing a thin horizontal line
• Auto Focus focuses on an object in the center of the
screen; objects around the screen edges may not be
properly in focus.
SPEED DOME CAMERA
46 User Guide
Through this menu you can set up the camera’s focus mode
when zooming.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Mode :
- Auto : Auto-focuses when zooming.
- Tracking : Focuses manually when zooming.
- Off : D
isable the focus modes when zooming. (Full
manual mode)
Speed :
- Slow/Fast : Adjusts the zooming speed.
➡
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
➡
Focus & Zoom
Focus Mode ONE SHOT AF
② Zoom Tracking
③ Digital Zoom OFF
➡
Zoom Tracking
Mode
② Speed
AUTO
FAST
SPEED DOME CAMERA
47 User Guide
Functional Description
2. White Balance
3. Exposure
▶ Main Menu/Camera Setting/White Balance
▶ Main Menu/Camera Setting/Exposure
The White Balance menu adjusts the balance of the screen
colors under different lighting conditions.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Setting
Functional Description
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
- ATW : Adjusts the screen color automatically.
- Indoor : Adjusts the screen color to be optimal in an
indoor environment. (Operating Temperature:
about 1,800°K ~ about 10,500°K)
- Outdoor : Adjusts the screen color to be optimal in an
outdoor environment. (Operating Temperature:
about 3,600°K ~ about 10,500°K)
- AWC : Adjusts the screen color to be optimized to the
current lighting and monitor conditions. Using this
setting may require an readjustment if the lighting
conditions changes.
- MANUAL : Enables customization the Red and Blue gains.
OFF
Medium
Medium
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
➡
Exposure
Notes
White Balance may not work properly under the following conditions.
When the color temperature of the environment surrounding the subject is out of the
control range.(e.g. Clear sky or sunset)
When the ambient illumination of the subject is dim.
If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, White Balance adjustments may not deliver
consistent results.
SPEED DOME CAMERA
48 User Guide
Brightness
Iris
Shutter
Sens-Up
050
AUTO
--AUTO
The Exposure settings are to control the camera’s exposure
meter.
Brightness : Adjusts the screen brightness.
(Over 50: Brighter, Under 50: Darker)
Iris :
- Auto : Automatically adjusts the exposure meter.
- Manual : Enables manual adjustment of the exposure
meter. (Over 50: Brighter, Under 50: Darker)
Shutter : Controls the camera’s electronic shutter.
- --- : The shutter speed is fixed at 1/60 for NTSC and 1/50
for PAL. Operates when Iris is on the Auto Mode.
- ESC : Adjusts the shutter speed automatically according
to the screen brightness. Operates when Iris is on
the Manual Mode.
- A.FLK : S elect this setting when you experience picture
flickering. Flickering can happen when artificial
lighting frequencies clash with camera frame rates.
- Manual : Enables manual adjustment of the shutter speed.
Sens-Up :
- Auto : Automatically detects light levels and maintains a
clear picture at night or under low-light conditions.
- Sens-Up Limit : Adjusts to the maximum-powered zoom
per frame.
Notes
• For optimal performance of the A.FLK mode, avoid
using the mode in conjunction with Backlight.
• While the Internal Sync mode is in effect, setting the
shutter to '---' and facing the camera directly to a
bright light source may cause poor camera
performance.
• Sens-Up is disabled when the shutter is in Manual or
A. FLK mode.
SPEED DOME CAMERA
49 User Guide
Functional Description
Functional Description
4.2 WDR(SPU-3750T Only)
▶ Main Menu/Camera Setting/Back Light/WDR
4. Backlight
4.1 Backlight Mode Settings
▶ Main Menu/Camera Setting/Back Light
When there are both bright and dark areas at the same time,
this mode makes both areas distinctive.
Main Menu
Unlike other cameras, Samsung Techwin’s unique SV-IV DSP
chip(SPU-3750T) / W-IV DSP chip(SPU-3700) gives you a clear
image of the subject even with bright backlight.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Back Light Mode :
- Off : Disables the Backlight mode.
- WDR : Activates the Wide Dynamic Range mode.
- HLC : Activates the High Light Compensation mode.
- BLC : Activates a user defined backlight compensation
mode.
➡
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
WDR Off
WDR ON
Camera Setting
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
WDR
Medium
Medium
Limit :
Three WDR sensitivity levels are available in 3: Low,
Medium , and High.
Note that the higher the sensitivity level, the lower the
contrast in the light and dark areas becomes.
Level :
Adjusts the screen brightness in WDR mode.
➡
WDR Setting
Limit
Level
Medium
50
Notes
• WDR is disabled if the shutter is in Manual mode.
• During WDR operation, noise, discoloration, spots, and
whitish symptoms may occur depending on lighting
conditions. If they occur, stop using WDR.
SPEED DOME CAMERA
50 User Guide
SPEED DOME CAMERA
51 User Guide
Functional Description
Functional Description
4.3 HLC
▶ Main Menu/Camera Setting/Back Light/HLC
The HLC settings selectively eliminates high lights in a limited
environment such as the entrance to an apartment parking lot
or gas station, and is useful to detect a small objects like car
license plates.
HLC is disabled during the daytime. While monitoring night
time car traffic, if car headlights reflects too much bright light
on the screen, the camera automatically eliminates the
headlamp lights and adjusts the color of the license plate
accordingly.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
HLC
Medium
Medium
<HLC ON>
<HLC OFF>
Level :
Adjusts the HLC sensitivity level.
HLC Setting
LOW
05
Mask Color :
Adjusts the mask color on the highlighted area.
Notes
• Even if HLC is on, car license plates may not be detectable depending on the location and
angle of the camera as well as the lighting condition.
SPEED DOME CAMERA
52 User Guide
You can selectively choose a screen area to see objects within
the area more clearly than others.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Four-direction Joystick Controls :
- Moving the joystick in all four directions—upward,
downward, left, and right—adjusts the location and size
of a selected area.
Zoom Control :
- Zoom Tele : Enlarges the size of a selected area.
- Zoom Wide : Reduces the size of a selected area.
➡
Camera Setting
HLC Masking Area
➡
Level
Mask Color
4.4 BLC Setting
▶ Main Menu/Camera Setting/Back Light/BLC
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
BLC
Medium
Medium
➡
↑:Up↓:Down ←:Left →:Right
W:Decrease T:Increase
Notes
• Color saturation may occur depending on the environment.
SPEED DOME CAMERA
53 User Guide
Functional Description
5. AGC
6. SSNR (Samsung Super Noise Reduction)
▶ Main Menu/Camera Setting/AGC
▶ Main Menu/Camera Setting/SSNR
AGC (Automatic Gain Control) adjusts the camera’s gain
control and the screen brightness if the camera has captured
an object under low-light conditions.
The Off, Low, Medium, High, and Manual modes are available.
Main Menu
Functional Description
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Main Menu
SSNR significantly reduces the amount of low luminance noise.
- Off : Disables the noise reduction function.
- Low : Reduces only a small amount of noise, but generates
almost no afterimage.
- Medium : The most commonly used mode. Reduces a suitable
amount of noise while generating a subtle
afterimage.
- High : R educes noise significantly, but generates obvious
afterimages.
➡
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Setting
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
Notes
• SSNR is disabled when the AGC mode is turned off.
SPEED DOME CAMERA
54 User Guide
SPEED DOME CAMERA
55 User Guide
Functional Description
7. Day & Night
8. Others
▶ Main Menu/Camera Setting/Day & Night
▶ Main Menu/Camera Setting/Others
The Day & Night function allows the camera to switch
between the Color and B/W modes.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Modes :
- Auto : Operates in Color mode most times, and switches
to B/W mode if a low light level is detected during
nighttime.
- Color : Operates in Color mode at all times.
- B/W : Operates in B/W mode at all times. By using the
Burst On/Off sub menu, burst signals can be
retained or disabled.
➡
Camera Setting
Functional Description
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
✽ If the camera is in B/W mode and connected to equipment
that requires external sync through burst signals, set the
Burst On/Off option to “On.”
Duration :
The camera’s light sensitivity is adjustable as in the chart
below. The camera’s ambient light diversion performance
may vary depending on its environment.
➡
Fast
Slow
Day & Night
① Mode
Duration
③ Dwell Time
COLOR
FAST
05 SEC
Color  B/W
2.5 Lux
0.8 Lux
B/W  Color
4 Lux
6 Lux
Dwell Time :
The duration of both the lighting conditions can be
customized to let the camera divert between the daytime
and nighttime settings.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Setting
① Focus & Zoom
White Balance
③ Exposure
④ Back Light
AGC
SSNR
⑦ Day & Night
⑧ Others
ATW
OFF
Medium
Medium
➡
Others
③
Sync
Stabilizer
Image Adj
Freeze
INTERNAL
OFF
OFF
Sync : Enables selecting Internal Synchronization or the
external Line Lock.
(SPU-3750T not supported)
- Internal : Synchronizes the camera’s output timing to the
internal crystal.
- Line Lock: Synchronizes the camera’s output timing to the
AC adapter power to synchronize multiple
cameras. This option is useful when using a
switch such as Matrix Switcher.
- Line Lock Phase : Enables setting the adapter’s
synchronization phase between 0 and 360°.
Stabilizer : The Stabilizer compensates for any small
movements of the camera caused by due to
the wind and other reasonable causes.
Notes
• The Stabilizer uses the digital zoom and may cause
low picture quality.
• The Stabilizer is disabled if the ambient light is too
low.
• The Stabilizer is disabled if the field of view has very
low or no contrast, e.g. The sky or a white wall.
Image Adj :
- Sharpness : Sharpens outlines of an image.
- Color : Adjusts the color density of an image.
Freeze : Stops or reanimates an image.
Notes
• The Auto mode is disabled when AGC is turned off. This function is only available when
the Color or B/W mode is selected.
• Using B/W mode under sunlight or a halogen lamp may decrease the focusing
performance.
SPEED DOME CAMERA
56 User Guide
SPEED DOME CAMERA
57 User Guide
Functional Description
Sequence Setting
10. Preset
9. Power On Resume and MD Dwell Time
10.1 Preset Location Saving
▶ Main Menu/Sequence Setting/Preset/Setting
▶ Main Menu/Sequence Setting
Power On Resume : This is useful when the power is disconnected and
reconnected due to power failures or other power
interruptions.
If the camera was performing a sequence action prior to a
power disconnection, the camera automatically resumes
the action when the power is reconnected.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Sequence Setting
Functional Description
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ON
ON
MD Dwell Time :
When Motion Detection under the Preset Edit menu is
selected, MD Dwell Time performs the Tour or Group
function.
While the camera is performing a sequence action, if
motion is detected from a selected preset location, the
camera pauses the sequence action operation and starts
monitoring the location instead for a duration that is set
under the MD Dwell Time menu.
If the motion is no longer detectable or the duration
expires, the camera aborts the monitoring operation and
then resumes the sequence action.
This function enables the memorization of a selected location
and activates the Pan, Tilt, and Zoom functions at that location.
Saved locations can be recalled using the Preset Execute
command.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Setting Up Preset Numbers :
Selecting the Preset Setting menu brings up a screen as
shown below. Move the joystick in all four directions to
select the desired number.
➡
Preset Setting
Sequence Setting
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ➡
Preset
Setting
Edit
Home Position OFF
Execute
Clear
Status
Preset = 001 (255)
ON
OFF
Saving Preset Locations :
Selecting a preset number and pressing the Enter key
redirects the menu to the screen shown below.
Using the joystick, adjust the location of the Pan and Tilt
functions and then set the Zoom and Focus command.
In Preset Settings, the Zoom and Focus command is
controllable only by the Zoom command. To switch
between Zoom and Focus, use the Preset 1 and 2
commands as shown below.
Preset Setting Z>Z00M
1+PST:ZOOM 2+PST:FOCUS
Use W/T Preset
SPEED DOME CAMERA
58 User Guide
SPEED DOME CAMERA
59 User Guide
Functional Description
Functional Description
10.2 Preset Edit
▶ Main Menu/Sequence Setting/Preset/Edit
You can edit the preset items such as Pan/Tilt location, Zoom
and Focus, which are selected among camera functions.
Main Menu
① Camera Setting
② Sequence Setting
....
PTZ :
Recalls saved locations using the Preset Settings command.
➡
Focus Mode :
Refer to the section entitled Setting Up Your Camera.
Sequence Setting
Brightness :
Refer to the section entitled Setting Up Your Camera.
① Preset
② Swing SEQ
③ Group SEQ
....
Iris :
Refer to the section entitled Setting Up Your Camera.
➡
Backlight :
Refer to the section entitled Setting Up Your Camera.
Preset
③
Setting
Edit
Home Position
Execute
Clear
Status
OFF
➡
Preset Edit
Preset = 001* (1~255)
➡
Preset Edit
[001]
271/045/1X
ONE SHOT AF
050
AUTO
⑤
⑧
PTZ
Focus Mode
Brightness
Iris
Back Light
Day & Night
After Act.
Scene Adj.
Day & Night :
Refer to the section entitled Setting Up Your Camera.
After Act :
Enables setting up an automatic action after the camera
arrives at a selected preset location.
- TRACK : Commands the camera to perform the Auto
Tracking function.
- MD : Commands the camera to perform the Motion
Detection function.
- None : Select this when no action is desired.
Scene Adj :
Enables setting the Shutter, AGC, SSNR, Sens-Up, White
Balance, and Stabilizer functions. For more information
about interface terminology, please refer to the section
entitled Setting Up Your Camera.
B/W
OFF
SPEED DOME CAMERA
60 User Guide
10.3 Preset Name Setting
▶ Main Menu/OSD Setting/Preset Name/Edit
Using this function, you can add names to preset locations.
up to 12 characters.
Once a name is entered, use the joystick and the Enter key to
perform the Set command and save the name.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
OSD Setting
① Camera
② Camera
③ Preset
④ Preset
....
ID
Name
Number
Name
ON
ON
➡
Preset Name
ON/OFF
Edit
OFF
➡
Preset Edit
Preset = 001* (1~255)
➡
PSET Name 001[
]
0123456789()[]#&%/~-=_
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
äöÖüÄÜàâçéèêëîïôûôùÿñÑáí
óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ
ABC->中文1 BACK SPACE CLR SET
SPEED DOME CAMERA
61 User Guide
Functional Description
Functional Description
10.4 Preset Execution/Deletion/Memory Check
▶ Main Menu/Sequence Setting/Preset
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Execute :
Recalls a saved preset location.
Clear :
Deletes the selected preset location.
Status :
Opens a map of saved preset locations.
An area saved as a preset location is displayed with the
'■' icon.
➡
Sequence Setting
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time Preset Status
ON
OFF
➡
Preset
③
Setting
Edit
Home Position
Execute
Clear
Status
Home Position :
Sets one of the currently configured preset positions as the
home position.
Main Menu
11. Swing SEQ
OFF
:
:
:
:
:
:
:
:
:
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
➡
Preset Status
SPEED DOME CAMERA
001
021
041
061
081
101
121
141
161
181
201
221
241
:
:
:
:
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
□□□□□ □□□□□ □□□□□ □□□□□
62 User Guide
▶ Main Menu/Sequence Setting/Swing SEQ
The Swing function commands the camera to move between 2
selected locations, monitoring the route.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Pan Swing :
Activates the Pan function for the Swing operation.
Tilt Swing :
Activates the Tilt function for the Swing operation.
P&T Swing :
Activates both the Pan and Tilt functions for the Swing
operation.
Swing Settings/Execute/Clear :
- Settings : Each of the Swing menus have sub menus with
the settings.
➡
Sequence Setting
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ➡
Swing SEQ
① Pan Swing
② Tilt Swing
③ P&T Swing
➡
Pan Swing
ON
OFF
① Setting
② Execute
③ Clear
➡
Pan Swing SET
[001]←→[***]
SPEED=64 (1~64)
DWT =003(1~128)(s)
Select 2 preset locations by using the joystick.
Speed indicates the camera’s movement speed. DWT indicates
the camera’s duration of stay at a preset location.
- Execute: Executes the Swing operation.
- Clear: Deletes data in the Swing memory.
SPEED DOME CAMERA
63 User Guide
Functional Description
12. Group SEQ
13. Tour SEQ
▶ Main Menu/Sequence Setting/Group SEQ
▶ Main Menu/Sequence Setting/Tour SEQ
Selecting Group SEQ recalls a group of multiple preset
locations in a consecutive manner. A group can contain up to
255 preset locations.
Main Menu
Functional Description
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Setting :
Using the joystick, enter desired preset numbers into the
PSET section. DWT indicates the camera’s duration of stay
at a preset location. SPD shows the camera’s movement
speed by 64 different levels.
➡
Sequence Setting
Group SEQ 1
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ➡
Group SEQ
① Group
② Group
③ Group
④ Group
....
1
2
3
4
ON
OFF
NO
001:
002:
003:
004:
005:
006:
007:
PSET DWT(s) SPD
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
*** : 003 : 64
Execute :
Executes the group operation.
Clear :
Deletes the selected group.
Selecting Tour SEQ recalls groups of preset locations in a
consecutive manner. Up to 6 groups can be listed for this
function.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Settings :
Selecting the Settings menu brings up the following screen.
Using the joystick, you can enter desired group numbers to
the Group section. DWT indicates the camera’s standby
time before a new group is recalled.
➡
Tour SEQ
Sequence Setting
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ➡
Tour SEQ
Setting
Execute
Clear
ON
OFF
NO Group DWT(s)
01: *
003
02: *
003
03: *
003
04: *
003
05: *
003
06: *
003
Execute :
Executes the group operation.
Clear :
Deletes the selected group.
➡
Group SEQ 1
Setting
Execute
Clear
SPEED DOME CAMERA
64 User Guide
SPEED DOME CAMERA
65 User Guide
Functional Description
14. PTZ Trace
15. Auto Run
▶ Main Menu/Sequence Setting/PTZ Trace
▶ Main Menu/Sequence Setting/Auto Run
Maximum 4 patterns of the manual operation paths (for Pan,
Tilt, Zoom and Focus) are memorized and replayed.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Replay :
Replays a route saved by the Trace function. Use the Stop
button to stop the replay.
Memorize :
Up to 120 seconds of a memory can be saved. The memory
duration varies depending on the difficulty level of the PTZ
Trace action. If the memory capacity is full, the Over
message appears and the memorization action is
terminated.
➡
Sequence Setting
Functional Description
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time ➡
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Sequence Setting
①
②
③
④
⑤
⑥
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
MD Dwell Time Auto Run
Mode
Time
Trace
Trace
Trace
Trace
ON
OFF
Time :
Enables setting up an Auto Run duration. (The duration can
be 1~60 seconds, or 1~60 minutes.)
➡
PTZ Trace
①
②
③
④
Mode :
- Home : Auto run Home Position (Refet to the Preset
Menu.)
- Preset : Auto run a selected preset number.
- Swing : Auto run a selected Swing mode.
- Group : Auto run a selected Group mode.
- Tour : Auto run a selected Tour mode.
- Trace : Auto run a selected trace mode.
- A.Pan : Auto run a 360-degree pan. To activate the
panning command, you need to set up the
camera's tilt angle and auto pan speed manually.
➡
ON
OFF
If there is no controller operation by the user for a certain time,
the sequence operation designated by the user will be
executed.
Main Menu
1
2
3
4
OFF
30 SEC
➡
PTZ Trace 1
Replay
Memorize
SPEED DOME CAMERA
66 User Guide
SPEED DOME CAMERA
67 User Guide
Functional Description
Functional Description
P/T Setting
17. Area Setting
▶ Main Menu/P/T Setting/Area Setting
16. Pan/Tilt Limit
▶ Main Menu/P/T Setting/Pan/Tilt Limit
Main Menu
The moving ranges in the Pan/Tilt directions can be limited.
Position :
Selecting the Position menu brings up the following screen
if it is for the Pan Limit setting. Move the joystick left and
right to select a movement range from the starting point to
the end.
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Start Limit
End Limit
➡
P/T Setting
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
⇨
Enter: Set
ON
ON
OFF
➡
ESC: Exit
Enter: Set
ESC: Exit
The following picture shows the Tilt Limit setting.
Move the joystick left and right to select a movement
range from the starting point to the end.
Start Limit
End Limit
Pan/Tilt Limit
⇨
① Pan Limit
② Tilt Limit
➡
Enter: Set
ESC: Exit
Enter: Set
ESC: Exit
Pan Limit
① Position
② ON/OFF
OFF
On/Off :
Cancels or activates the Pan/Tilt Limit functions.
SPEED DOME CAMERA
68 User Guide
The Area Setting menu enables selecting certain locations in
the course of the Pan and Tilt operation, and then display the
areas with the OSD (On Screen Display) texts when the camera
passes through them. Up to 8 areas can be selected.
Main Menu
① Camera Setting
② Sequence Setting
③ P/T Setting
④ OSD Setting
⑤ Alarm Setting
⑥ Initialize
Status
Area Name :
You can add names to selected areas. Names can be up to
12 characters and can be entered via the joystick and the
Enter key. Once a name is entered, use the joystick and the
Enter key to perform the Set command and save the name.
➡
P/T Setting
① Pan/Tilt Limit
② Area Setting
③ Area Masking
Prop. P/T Digital Flip
Image Hold
⑦ Auto Track1
⑧ Auto Track2
ON
ON
OFF
➡
Position :
As shown in the picture below, move the joystick to select
the upper left corner and lower right corner of an area.
Area Setting
① Area
② Area
③ Area
④ Area
....
Area Name 001[
]
0123456789()[]#&%/~-=_
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
äöÖüÄÜàâçéèêëîïôûôùÿñÑáí
óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ
ABC->中文1 BACK SPACE CLR SET
1
2
3
4
Start Position
⇨
➡
Area 1
Area Name
Position
ON/OFF
End Position
Enter: Set
OFF
ESC: Exit
Enter: Set
ESC: Exit
On/Off :
Cancels or activates the display function of selected areas.
SPEED DOME CAMERA
69 User Guide
Functional Description
Functional Description
18. Area Masking
19. Prop. P/T
▶ Main Menu/P/T Setting/Area Masking
If a monitoring location includes a highly private area, the area
can be selectively excluded from monitoring.
Main Menu
①
②
③
④
⑤
⑥
▶ Main Menu/P/T Setting/Prop. P&T
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Position :
As shown in the picture below, move the joystick to select
the upper left corner and lower right corner of an area.
Start Position
End Position
➡
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
Enter: Set
ON
ON
OFF
ESC: Exit
Enter: Set
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
P/T Setting
ESC: Exit
On/Off :
Cancels or activates the Area Masking function.
➡
➡
⇨
P/T Setting
This commands the camera to change the Pan and Tilt speed
automatically according to the current zoom ratio. Moving the
joystick clockwise (Tele) slows down and counterclockwise
(Wide) accelerates the Pan and Tilt speed, allowing detailed
adjustments.
Turning this “Off” executes the function the optical 1x zoom
speed regardless of how far the lens is zoomed in.
Main Menu
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
ON
ON
OFF
Area Masking
① Mask
② Mask
③ Mask
④ Mask
....
1
2
3
4
➡
Mask 1
Position
ON/OFF
OFF
SPEED DOME CAMERA
70 User Guide
SPEED DOME CAMERA
71 User Guide
Functional Description
20. Digital Flip
21. Image Holding
▶ Main Menu/P/T Setting/Digital Flip
▶ Main Menu/P/T Setting/Image Hold
Digital Flip is useful to monitor a moving object or a person
passing directly under the camera.
When an object or a person passes directly under the camera,
the camera tilt monitor follows the object or person over 100
degrees to the other side of the tilt area without panning. The
screen inversion occurs at 100 degrees or higher and is
digitally adjusted.
Main Menu
Functional Description
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
➡
P/T Setting
P/T Setting
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
When the camera is moving between presets locations, this
function freezes the cameras image until the camera reached
the next location. This is useful to help the screen observer
keep sharp eyes and to monitor multiple locations within a
network.
Main Menu
ON
ON
OFF
SPEED DOME CAMERA
72 User Guide
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
ON
ON
OFF
SPEED DOME CAMERA
73 User Guide
Functional Description
22. Auto Track 1 (SPU-3750T Only)
▶ Main Menu/P/T Setting/Auto Track1
This commands the camera to automatically follow a moving
object or a person on the screen.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Auto Track :
On/Off : Turns Auto Track on or off.
Camera Height :
Adjusts the height of the camera. Tracking performance
may decrease if the camera height is not adjusted properly.
(Height: 2.5m ~ 30m)
➡
P/T Setting
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
ON
ON
OFF
Auto Track 1
Auto Track
Camera Height
Object Size
Sensitivity
Zoom Control
Auto Release
Auto Return
Lost Mode Auto Release :
Enables setting a maximum duration to follow an object. When the duration expires, the camera
stops following the object and returns to the start position to follow another objects.
Auto Return :
- Off : C ommands the camera to stay on the location the last object stopped at instead of
returning to the initial position.
- Time Setting : Sets a duration for the camera to standby upon the Auto Release expiration and
then return to the start position.
Lost Mode :
Sets up an action for the camera in case the object it is following goes out of the detection
range.
- Stop : Commands the camera to stop and abort tracking at the spot where its object
disappeared.
- Research : Commands the camera to stop and standby at the spot where its object
disappeared.
- Zoom-Out : Commands the camera to zoom out and look for a new object in case its current
object disappears.
Sensitivity :
The object detection sensitivity is adjustable. Lower the
sensitivity if the camera catches a swaying tree branch,
raindrops, or snowflakes during the Auto Track operation.
➡
Object Size :
Sets a maximum zoom ratio to zoom in on an object if the
Zoom function is used for the tracking operation.
- Small : Zooms in on a tracking object up to 1/4 of the
screen height.
- Medium : Zooms in on a tracking object up to 2/4 of the
screen height.
- Large : Zooms in on a tracking object up to 3/4 of the
screen height.
Functional Description
OFF
02.5M
SMALL
HIGH
OFF
OFF
OFF
STOP
Zoom Control :
The function’s zoom control settings are as follows.
- Off : Disables the Zoom control.
- One Shot : P erforms the Zoom control once during the
Motion Detection and Auto Track operations.
Depending on the movement detection, the
camera performs the Zoom control multiple
times.
- Continuous : Performs the Zoom control continuously.
SPEED DOME CAMERA
74 User Guide
SPEED DOME CAMERA
75 User Guide
Functional Description
Functional Description
- Target (
23. Auto Track 2 (SPU-3750T Only)
object is detected, a square grid appears and surrounds the object.
▶ Main Menu/P/T Setting/Auto Track2
Auto Track 2 provides Auto Track related settings other than
the ones programmed in the Auto Track 1 menu.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Zone Setting :
- Position : E nables the designation of certain areas as
zones for the Auto Track operation. The setting
procedures are the same as for Area Mask.
- Mode : Two modes are available: Mask and Alarm. When
Mask is selected, the camera does not follow the
object entering the masked zone. This is useful if
the camera catches swaying objects such as tree
branches and flags during the Auto Track peration.
When Alarm is selected, the camera activates an
alarm if an object enters the zone.
- On/Off : Activates or deactivates the Zone function.
➡
P/T Setting
①
②
③
⑦
⑧
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T Digital Flip
Image Hold
Auto Track1
Auto Track2
ON
ON
OFF
➡
Auto Track 2
① Zone Setting
Indicator
Target Lock
OFF
OFF
Track Zone
① Zone
② Zone
③ Zone
④ Zone
⑤ Zone
⑥ Zone
⑦ Zone
⑧ Zone
1
2
3
4
5
6
7
8
Zone 1
① Position
② Mode
③ ON/OFF
⇨
MASK
OFF
Indicator :
Indicates objects with icons on the screen.
- Off : Disables the Indicator function.
- On ( ) : Indicates both the pointer and target.
- Pointer ( ) : Indicates the indicator when following an
object using the joystick; shows as a cross
in the center of the screen.
SPEED DOME CAMERA
76 User Guide
) : Indicates the camera’s target for the Auto Track operation; when a moving
Target Lock :
Target Lock is useful to select and follow an object using the Auto Track mode while operating
the camera with the joystick. Target Lock can be turned On or Off.
To activate the Auto Track mode, turn on Target Lock, select an object to follow, and then press
Enter.
Notes
• Auto Track is specifically to track down intruders. Thus, it may not be suitable to monitor a
crowd.
• If the camera is not safely secured, tracking errors may occur.
• If the camera lens is smeared with foreign substances or is scratched, an error may
occur causing the camera to not behave as expected.
• The camera may not follow an object or tracking errors may occur under the following
conditions:
∙ If the contrast between an object and the background is low
∙ If the camera lens is smeared with foreign substances, e.g. raindrops or snowflakes
∙ If the lighting is changing dramatically
∙ If many movements around an object are detected
∙ If an object moves vertically on the optic angle of the camera
∙ If an object passes directly under the camera
∙ If an object creates inconsistent light levels, e.g. the object is too shiny or flickering
∙ In environments where there are light reflections causing internal reflections of camera,
e.g. windows, shiny road surfaces, and backlights
∙ If an object moves behind large and tall objects, e.g. telephone poles
∙ If an object moves too quickly
∙ If the camera is vibrating
SPEED DOME CAMERA
77 User Guide
Functional Description
Functional Description
Alarm Setting
OSD Setting
25. Alarm Setting
24. OSD Setting
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
OSD Setting
②
④
25.1. Setting Up Alarm Input
▶ Main Menu/Alarm Setting/Alarm Input
▶ Main Menu/OSD Setting
Camera ID
ON
Camera Name
Preset Number ON
Preset Name ON
Sequence Status ON
Area Name
OFF
PTZ Position ON
Language
English
XXX Name 001[
]
0123456789()[]#&%/~-=_
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
äöÖüÄÜàâçéèêëîïôûôùÿñÑáí
óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ
ABC->中文1 BACK SPACE CLR SET
Camera ID :
Displays or hides Camera ID in the upper left of the screen.
Camera Name :
Add a name to the camera. (First check the Note.)
Preset Number :
Displays or hides Preset Numbers on the screen.
Preset Name :
Add names to preset locations. (First check the Note.)
Sequence Status :
Displays or hides the status of a sequence action that is in
progress.
Area Name :
Displays or hides the Area Name for the Area Settings on
the screen.
PTZ Position :
Displays or hides the status of the Pan, Tilt, and Zoom
operation that is in progress.
Language :
Enables changing the system language. This camera
supports English, Chinese, French, German, Spanish, and
Italian.
Alarm Enable :
- On/Off : Enables or disables the Alarm function.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
MOD :
Enables selecting an Alarm Input method.
- NO (Normally Open)
IN 1.2.3
IN 1.2.3
⇨
➡
Alarm Setting
②
③
④
ALM GND
Alarm Enable
OFF
Alarm Input
Alarm Output
Aux Output
➡
ALM GND
ALARM OFF
ALARM ON
- NC (Normally Closed)
ALM MOD P SEQ. NO
IN1 OFF 1
IN2 OFF 2 IN3 OFF 3
OFF
OFF
OFF
IN 1.2.3
IN 1.2.3
⇨
ALM GND
✽ When selecting the Camera Name and Preset
Name, the screen displays the Left keypad.
Names can be up to 12 characters and can be
entered via the joystick and the Enter key. Once a
name is entered, use the joystick and the Enter key
to perform the Set command and save the name.
SPEED DOME CAMERA
78 User Guide
ALM GND
ALARM OFF
SPEED DOME CAMERA
79 User Guide
ALARM ON
Functional Description
Functional Description
25.2. Alarm Output
▶ Main Menu/Alarm Setting/Alarm Output
Notes
• As shown in the picture above, the Alarm Input must be entered with the Open or Closed
switch signals. Supplying power without entering the signals may damage the product.
P (Priority) :
Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated,
the alarm with the highest priority activates before the others. Once the alarm is canceled, the
next highest priority alarm activates.
SEQ :
Enables setting up a sequence action for the camera in response to an alarm. Available
sequence actions are Preset, Swing, Group, Tour, Trace and A.Pan.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Alarm Setting
②
③
④
Alarm Enable
OFF
Alarm Input
Alarm Output
Aux Output
➡
Alarm Output
Output
Time □1□2□3□MD□TRK
OFF
Setting :
Enables selecting an Alarm Output method.
- 1, 2, 3 and MD on the menu selection indicate the alarm
input port and motion detection input. Up to 3 alarm
inputs can be set for each MD (Motion Detection) and
TRK (Auto Track). Alarm output port can be used for more
than 2 alarm inputs along with ones for MD and TRK.
✽ The TRK function becomes activated only if the Zone mode
under Zone Settings under Auto Track 2 is set to Alarm.
Time :
Enables selecting an Alarm Output method.
- On : Retains an alarm output for a set duration from a
minimum of 1 second to a maximum of 60 hours
upon the alarm occurrence.
- Momentary : Retains an alarm output only until the alarm
is canceled.
✽ The Alarm Output is equipped with a relay circuit. The
operation of the alarm output port is as shown in the
diagram below.
NO
NO
COM
NC
⇨
Alarm Out OFF
COM
NC
Alarm Out ON
Notes
• Connecting the power connector and GND incorrectly to the NC/NO and COM ports may
cause a short circuit and fire, damaging the camera.
• The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and
250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s
lifespan and damage it.
SPEED DOME CAMERA
80 User Guide
SPEED DOME CAMERA
81 User Guide
Functional Description
Functional Description
Initialize
26. Initialize
25.3. Aux Output
▶ Main Menu/Alarm Setting/Aux Output
AUX Output menu is to operate the camera’s peripheral
devices such as lamps and sirens through the controller and
switches as well as through network communications.
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
On/Off :
- Cancels or activates the Aux function.
Time :
Enables setting up a duration for the Aux output when the
Aux command is transmitted from the controller. A
duration can be selected from a minimum of 1 second to a
maximum of 60 minutes.
➡
Alarm Setting
②
③
④
Alarm Enable
OFF
Alarm Input
Alarm Output
Aux Output
NO
COM
AUX Off
NO
⇨
COM
AUX On
➡
AUX Output
On/Off
Time
OFF
00 SEC
Notes
• Connecting the power connector and GND incorrectly to the Aux terminal’s NO and COM
ports may cause a short circuit and fire, damaging the camera.
• The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and
250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s
lifespan and damage it.
SPEED DOME CAMERA
82 User Guide
26.1. Initialization Menu
▶ Main Menu/Initialize
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Initialize
① Power On Reset
② Factory Default
③ Camera Default
Auto Refresh
OFF
⑤ Auto Track Default
⑥ Fan Life
Power On Reset : Restarts the camera.
Factory Default :
Enables resetting the camera to its factory default settings.
When the mode is selected, all custom data such as preset
locations is deleted from the camera. Use this function if it
is necessary to reset the settings of the camera.
Camera Default :
This mode can be used if the camera module has been
replaced and you want to keep the camera's existing
settings for the new module.
To reset the camera, first replace the old module with a
new camera module. When the replacement is properly
installed, turn on the module, then execute this command.
Auto Refresh :
Enables optimizing the status of the camera’s built-in
electric circuits and components on a regular basis. (A
regular operation can be scheduled.)
This mode can be used to maintain and repair the current
settings of the camera when anomalous operations occur:
e.g. The camera happened to directly face a light source, or
the settings have been canceled after the camera
repeatedly rotated in all four directions for a long time to
monitor a specific location.
The default setting is Off.
- Off, 1~7 Days : Selecting Off disables Auto Refresh and
selecting 1~7 Days automatically executes it after 1~7
days has passed.
✽ Auto Refresh takes approximately 10 seconds to finish. If
Auto Refresh activates in the middle of a sequence action,
the camera pauses the sequence action and performs an
Auto Refresh, then resumes the sequence action once the
refresh is complete.
Auto Track Default : Enables resetting the Auto Track settings.
Fan Life : Enables setting the Fan Life.
SPEED DOME CAMERA
83 User Guide
Functional Description
Functional Description
Status
26.2 Setting Fan Life
▶ Main Menu/Initialize/Fan Life
Message Display :
The following alert message appears 2 months before the
fan lifespan expires: Fan Life was Expired. Replace the Fans.
"Fan life Expired., Replace the Fans"
-ON : Displays alert messages. (Default Option)
-Off : Hides alert messages.
✽ The [Off] option does not automatically delete the messages
but keeps them hidden from the screen. To show the
messages again, change it back to [On]. (Displays only
messages that are not deleted by [Message Clear].)
Main Menu
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Initialize
① Power On Reset
② Factory Default
③ Camera Default
Auto Refresh
OFF
⑤ Auto Track Default
⑥ Fan Life
➡
Fan Life
②
③
Message Display ON
Message Clear
Time Reset
Time Remain.(hour) 49000
Message Clear :
Deletes alert messages from the screen.
✽ [Cleared] messages do not display on the screen when the
display option changes back to [On].
Time Reset :
Resets and starts counting the lifespan of a fan when it is
replaced.
(The Reset function activates only after the fan lifespan
alert message is active.)
✽ This function counts the lifespan of a fan only during its
operation; it may be used longer than the expiration date
displayed on the OSD.
27. Status
▶ Main Menu/Status
Main Menu
Displays the settings and version of the dome camera.
Cam Model :
Indicates the model name of the camera.
Cam Version :
Indicates the software version of the camera.
Dome Version :
Indicates the version of the camera control board.
CON Protocol :
Indicates the status of the current protocol.
Dome ID :
Dome Camera ID
Controller :
Indicates the settings of the current communications mode.
Track Version :
Indicates the Auto Track software version of the camera.
COAX VERSION :
Indicates the software version of the Coax communication
①
②
③
④
⑤
⑥
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
➡
Camera Status
CAM MODEL =
CAM VERSION =
DOME VERSION=
CON PROTOCOL=
DOME ID =
CONTROLLER =
TRACK VERSION=
COAX VERSION=
37NHU
3.8
1.16
SAMSUNG TW
001
Simplex-9600
1.08
1.04
Time Remain.(hour) :
- 49000 : Indicates the remaining lifespan of the current
fan. (Unit: hours)
- The remaining time refreshes when the [Fan Life] menu is
selected and the [Enter] key is pressed in the [Time Remain
(hour)] option.
SPEED DOME CAMERA
84 User Guide
SPEED DOME CAMERA
85 User Guide
Troubleshooting
Problem
Controller does not work.
No picture is displayed on
monitor.
The picture is too dark/
bright.
The monitor displays a
white image.
Picture is out of focus.
Digital noise appears in
picture.
Cause and Solution
▶ Check if the camera and peripheral devices are
properly connected.
▶ Verify the setups of ID, protocol, and baud rates.
▶ Check if power cable is securely connected to the
camera and the monitor.
Check if the video cable is properly connected.
Consult the operation manual of the system
controller connected to the camera.
▶ Check if the iris of the lens is closed.
Adjust the menu for the iris of the lens.
▶ Check the camera's fixed shutter speed.
Adjust the camera's shutter menu.
▶ Check the camera's Brightness menu.
Adjust the camera's Brightness menu.
▶ Check if the iris of the lens is open.
Adjust the menu for the iris of the lens.
▶ Check if the dome cover or the camera lens is
dirty or smudged. If it is, clean the dirt off.
▶ Verify the distance between the camera and the
subject, as well as the subject's surroundings.
Camera may have difficulty focusing on a subject
against a white background.
▶ If Auto Focusing is having difficulty focusing on a
particular subject, set Focus Mode to Manual and
adjust the focus by yourself.
▶ Use the camera's reset menu to restore the
camera settings in order to default.
▶ Adjust Sharpness level.
▶ Check if the video cable is properly connected.
▶ Make sure that the power cable and video cable
do not exceed the recommended maximum
lengths.
▶ Adjust Sharpness level.
SPEED DOME CAMERA
86 User Guide
Troubleshooting
PAGE
▶ Check the White Balance.
48
▶ Adjust Color Menu in Image Adj.
57
23~32
▶ C
heck if the dome cover or the camera lens is
dirty or smudged. If it is, clean the dirt off.
-
20~21
▶ C
heck if the camera is pointing directly at a
fluorescent light or sunlight. If so, change the
camera's direction to remove the flickering.
-
34
49
49
49
49
-
-
46~47
83
57
33
57
Picture's colors are not
good.
The picture is flickering.
Afterimages appear in
▶ Check Sens-Up settings.
49
picture.
Camera switches between
▶ Adjust Duration and Dwell Time in Day & Night
color and B&W modes
56
menu.
frequently.
A circular object appears on ▶ You are seeing a pinpoint-like injection artifact on
screen when the camera is
the dome cover.
pointing straight down.
The camera is functioning normally.
▶ Check if power cable is securely connected to the
camera and the monitor.
Check if the video cable is properly connected.
20~21
Consult the operation manual of the system
controller connected to the camera.
Pan, tilt, zoom, and/or focus
do not work.
▶ Check if Pan Limit and/or Tilt Limit are set.
68
If so, remove the limit(s).
▶ A motor or the lens may be overheated.
If so, contact your service personnel or system
provider for assistance.
The camera's position
▶ This phenomenon may happen, since the motors
differs from the position
have a margin error of ±0.1˚.
defined in a preset.
▶ Check if Preset or another operation mode has
59~62
Sequence configuration of
been set.
the camera does not work.
▶ Check the Auto Refresh settings.
83
The upper side of the
picture is dark when the
▶ You are seeing the camera's internal cover. The
camera is on the horizontal
camera is functioning normally.
reference point.
SPEED DOME CAMERA
87 User Guide
Troubleshooting
Camera suddenly turns on
or moves to a preset
position by itself.
Although The subject is
moving, but Auto Tracking
does not work.
Auto Tracking suddenly
functions incorrectly.
Troubleshooting
▶ Check the Auto Run settings.
Auto Run puts a camera through a predefined
action sequence if the user does not use the
Controller to operate the camera for a certain
period of time.
67
▶ Check the Auto Refresh settings.
Auto Refresh optimizes the camera's circuitry and
components according to a predefined schedule.
83
▶ Check if the subject is in an area set of Area
Masking.
70
▶ C
heck the Auto Release settings.
Auto Release stops tracking a subject after a
preset period of time, and returns the initial
position of the camera to track a new subject.
75
▶ Sensitivity may be set too low for the camera to
detect a moving subject.
Adjust a higher Sensitivity setting.
74
▶ Check if the subject is too small.
Adjust picture angle to increase the subject size.
42
▶ Check if there are trees, grass, flags, or other
subjects being moved by wind, and/or water,
glass, paved roads, or other subjects with a highly
reflective surface.
If so, set Area Masking of the area containing such
subjects.
70
▶ The sensitivity of the camera's threshold detection
may be set too high.
Adjust a lower Sensitivity setting.
74
▶ Check if it is raining/snowing.
Auto Tracking may function incorrectly or fail to
function at all if the dome cover is contaminated
with water or snow particles.
SPEED DOME CAMERA
88 User Guide
A subject being AutoTracked is out of screen
immediately.
Coxial communication does
not work.
I turned on the power, but
the camera didn't start
running.
I can’t see the screen.
(The screen is black.)
-
The camera stops in the
Initialize mode and won’t
proceed to the next mode.
▶ C
heck Object Size settings.
If Object Size is set too small, adjust it to a larger
72
value.
▶ Check if the monitored area contains multiple
moving subjects.
Auto Tracking is intended for monitoring intruders,
and may not be suitable for crowd monitoring.
▶ Check the distance between the camera and the
monitor.
▶ If the distance between the camera and the
monitor exceeds the recommended maximum,
please use an auxiliary video amp.
▶ Please check the environment temperature; the
camera may not operate properly if it has been left
at temperatures lower than -50℃ for a prolonged
duration.
▶ The motor may malfunction at temperatures lower
than -20℃; please turn on the camera in Standby mode instead of [Initialize].
▶ Keep in Standby mode for at least 90 minutes.
Once the internal temperature reaches -20℃ or
higher, the camera automatically resets itself and
activates the [Initialize] mode for normal operation.
▶ When the camera’s internal temperature drops
down to -20℃ or lower, it becomes unable to
transmit video signals and may cause a black
screen.
▶ A black screen does not indicate camera
breakage; it resets itself and starts displaying
video again once its internal temperature reaches
-20℃ or higher.
▶ The motor may malfunction at temperatures lower
than -20℃; please turn on the camera in Standby mode instead of [Initialize].
▶ Once the camera's internal temperature reaches
-20℃ or higher, it resets itself and activates the
[Initialize] mode for normal operation.
SPEED DOME CAMERA
89 User Guide
Troubleshooting
▶ When the camera's internal temperature is
between -10℃ to -20℃, the motor may
malfunction, limiting the use of the Sequence and
I can use the controller, but I
Turbo commands.
can’t activate the Sequence
command.
▶ Once the internal temperature reaches -10℃ or
higher, all Sequence modes become reactivated
normally.
I can't get rid of this
message
from the screen: “ Fan life
Expired. Replace the Fans.”
Product Specification
Model Name
-
-
Imaging Device
▶ Such symptoms may occur if the camera's
temperature increases from -20℃ or lower to
The camera suddenly resets
-20℃ or higher.
itself while displaying the
▶ The motor may malfunction at temperatures lower
black screen.
than -20℃; please reset the camera and
reactivate the [Initialize] mode.
“Please Check Heater
System” appears.
▶ The heater may malfunction. Turn off the camera
and call where you bought.
"Auto Refresh(Wait)"
appears and the camera
reboots.
▶ Such symptoms may occur if the camera's
temperature increases from -10℃ or lower to
-10℃ or higher to prevent the malfunction of
motor.
1/4 inch, Double Density Interline Transfer CCD
1/4 inch, Super HAD color CCD
NTSC / PAL
Total Pixels
NTSC: 811(H) × 508(V) / PAL: 795(H) × 596(V)
Effective Pixels
NTSC: 768(H) × 494(V) / PAL: 752(H) × 582(V)
Scanning System
80
2:1 Interlace
Internal
Horizontal Scan
15.734 KHz
59.94 Hz
Horizontal
-
-
-
Min. Illumination
550 TV Line(Color)/680 TV Line(B/W)
0.7 Lux (50 IRE @ F1.6 Color)
0.03Lux (50 IRE @ F1.6 B/W)
90 User Guide
0.4 Lux (50 IRE @ F1.6 Color)
0.02Lux (50 IRE @ F1.6 B/W)
S/N (Y Signal)
50 dB
Video Output
CVBS:1.0Vp-p/75Ω
Zoom Ratio
37X (Optical),12X (Digital)
Focal Length
3.5~129.5mm (F1.6 ~3.9)
Min. Object
1.9m
H:55.5°(Wide)~1.59°(Tele)
Angular Field of
view
V:42.5°(Wide)~1.19°(Tele)
Focus
AUTO / MANUAL / ONE-SHOT
Zoom Speed
2.5sec
IRIS
• The Power cord's coating
has been damaged.
Continuing to use the product when its power cord is
• The power cord is hot to
damaged constitutes an electrical and fire hazard.
touch when the product is The power plug must be removed from the outlet
in operation.
immediately, and a qualified service personnel or
• The power cord gets hot
your system provider should be contacted for
after being folded or
assistance.
pulled on.
Internal/External(AC Line Lock)
Vertical Scan Rate
Check the Power cord's by periods
SPEED DOME CAMERA
SPU-3700
TV Standard
Synchronization
▶ Please make sure to "Clear" the message from
the screen.
SPU-3750T
AUTO/MANUAL
Lens Initialization
Auto Tracking
-
Built-In
Built-In
-
Horizontal
Rotation Angle
360° Endless
Horizontal
Rotation Speed
Manual:0.024°/sec ~120°/sec, Preset 500°/sec
Vertical Rotation
Angle
-5° ~ 185°
Vertical Rotation
Speed
Manual:0.024°/sec ~120°/sec, Preset 500°/sec
SPEED DOME CAMERA
91 User Guide
DECLARATION OF CONFORMITY
Product Specification
Model Name
SPU-3750T
SPU-3700
Preset Position
Max. 255 Point
Preset Accuracy
±0.1°
Camera ID
255
Day & Night
Backlight
AUTO / COLOR / BW
BLC / HLC / OFF
WDR / BLC / HLC / OFF
Dynamic Range
52dB
Application of Council Directive(s)
EMC-Directive 92/31 EEC and its amendments
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
Motion Detection
ON/OFF
European Representative Address
Stabilizer
ON/OFF
Equipment Type/Environment WEATHERPROOF DOME CAMERA
Model Name SPU-3750T/3700
On/Off (Selectable limit ~ 256X )
Beginning Serial NO. C10S7010007
LOW/MEDIUM/HIGH/MANUAL/OFF
Year of Manufacture 2009.07.01
Conformance to EN 55022 : 2006
RS-422/485, Coaxial Communication
EN 50130-4 : 2003
Samsung Techwin, Pelco-D, Pelco-P, Pelco Coaxitron,
Panasonic, Honeywell, AD, Vicon, Samsung Electronics, GE, BOSCH
Privacy Mask
ON/OFF (8 Areas)
SSNR
Sens-up
Gain Control
White Balance
Electronic Shutter
Serial Com.
Protocol
LOW/MEDIUM/HIGH/OFF
ATW/INDOOR/OUTDOOR/AWC/MANUAL
AUTO(NTSC:1/60~120,000sec, PAL:1/50~120,000sec)/MANUAL/A.FLK
Alarm
3 In, 1 Out, 1 Aux
Digtal Flip
ON/OFF
Waterproof
Standards
IP66(IEC-60529)
We, the undersigned, hereby declare that the equipment specified above conforms
Operating
Temperature/
Humidity
-50℃ to +50℃ / 20% to 80% RH
Storage
Temperature/
Humidity
-50℃ to +60℃ / 20% to 95% RH
Input Voltage
AC24V ± 10%
Power
Max.60W(When the heater and the fan work)
External
Dimensions
(Ø×D)
Weight
SPEED DOME CAMERA
Max.58W(When the heater and the fan work)
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name BON JUNG GU
Full Name
Position QUALITY CONTROL MANAGER Position Ø248×331mm
Place SUNGNAM, KOREA
Place
About 4.5Kg
Date 2009.07.01
Date
92 User Guide
SPEED DOME CAMERA
93 User Guide
MEMO
SPEED DOME CAMERA
94 User Guide
MEMO
SPEED DOME CAMERA
95 User Guide
SALES NETWORK
•
•
AMSUNG TECHWIN CO., LTD.
S
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
•
AMSUNG TECHWIN EUROPE LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
P/No. :Z6806-1026-01B
VAN 10. 04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement