CyberData 011049 SIP Call Button Owner Manual

Dimensions
Installation Quick Reference
The IP Endpoint Company
SIP Call Button
SIP Compliant
011049
4.53 [115.0]
Parameter
Factory Default Setting
IP Addressing
IP Address
4.53 [115.0]
DHCP
a
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
1.58 [40.2]
Typical System Installation
DIMENSIONS ARE IN INCHES [MILLIMETER]
Generic PoE Switch
1
Maximum Recommended Wall Cutout Dimensions
2
3
4
5
6
0.25 [6.4]
SIP Call Button
0.25 [6.4]
•
0.25 [6.4]
IP PBX Server
Download the SIP Call Button Operations Guide PDF file, from the SIP Call Button product page at:
http://www.cyberdata.net/products/voip/digitalanalog/callbutton/docs.html
0.25 [6.4]
Dimensions are in Inches [Millimeter]
Contacting CyberData
•
Create a plan for the locations of your SIP Call Buttons.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
Corporate Headquarters
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
IP Phone
SIP Call Button
Getting Started
Wall Cutout
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
SIP Call Button
(1) SIP Call Button Assembly
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930293M
(1) Wall Mounting Kit
(4) #6 x 1.25 inches
Sheet Metal Screw
Quick Reference
Quick Reference
930293M
(1) Gang Box Mounting Kit
(4) #6 Ribbed Plastic
Anchor
(4) #6-32 x 0.625-inch
Flat-Head Machine Screw
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Wall Mounting Options
RTFM Button
RTFM (SW1)
Pre Drill Holes
(4 Places) on Wall
When the device is operational and linked to a
network, you can use the Reset Test Function
Management (RTFM) button (SW1) to restore
the device to the factory default settings.
Backplate
Cable
Slots
Closed
Pick One of Four Mounting Hole
for Ground Wire Connection
To restore the device to factory default settings:
• Press and hold the RTFM switch until the
button LED starts blinking rapidly (about 10
seconds), then release the RTFM switch.
Wall
Cutout
Cable
Entry
Slot
Network Cable &
Ground Wire
(Not Provided)
121001A
Screw
Accessory Kit
Mounting
Screw (3x)
Gang Box Mounting Options
Terminal Block Connections
Cable
Slots
Closed
Backplate
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
4
Wall Cutout
Alternate Power Input:
1 = +12 to 24 VDC at 500 mA
2 = Power Ground
Backplate accept
Single Gang Box
or Two Gang Box
Cable
Entry
Slots
Wall Cutout
Relay Contact:
(1 A at 30 VDC for continuous loads)
3
4
3 = Normally Open Common
Relay
Contact:
4 = Normally Open
Contact
5 = Door Sense(1A
Input
at 30 VDC for continuous loads)
6 = Door Sense3Ground
= RelayReference
Common
Network Cable & Ground Wire
(Not Provided)
Mounting
Screw (3x)
4 = Relay Normally Open Contact
*Contacts 1 and 2 on the J3 terminal block are only for
5 = Door
Sense
Input 12VDC power
powering the device
from
a non-PoE
6
=
Door
Sense
Ground
Reference
source as an alternative to Network
PoE
power. Use of
121002B
Screw
Accessory Kit
Single Gang Box use two
Two Gang Box use Four
these contacts for any other purpose will damage the
device and void the product warranty.
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930293M
Pick One of Two or Four
Available Mounting Hole
for Ground Wire Connection
Quick Reference
Quick Reference
930293M
© 2015, CyberData Corporation, ALL RIGHTS RESERVED