OMEGA 23221C, 23222C, 23301C Hydraulic Truck Jack Operating Instructions & Parts Manual
Below you will find brief information for Hydraulic Truck Jack 23221C, Hydraulic Truck Jack 23222C, Hydraulic Truck Jack 23301C. These Hydraulic Truck Jacks are designed to lift vehicle loads consisting of one end of a vehicle. After lifting, vehicle must be supported by a pair of appropriately rated jack stands. The process of lifting includes connecting to an adequate air source, closing the release valve, centering the jack saddle under the lift point, squeezing the lift control valve, and transferring the load to jack stands. Lowering is accomplished by opening the release valve, raising the load high enough to clear the jack stands, removing jack stands carefully, and slowly turning the handle knob counter-clockwise.
Advertisement
Advertisement
Operating Instructions & Parts Manual
Hydraulic Truck Jack
Model
23221C
23222C (Low Profile)
23301C
Capacity
22 Ton
22 Ton
30 Ton
U.S. Patent No's.
5,341,723 • 5,946,912
Model 23301C
Models 23221C & 23222C
!
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
AdveRTenCIA
• Leer, comprender, y seguir las instrucciónes antes de utilizar el aparato.
• El manual de instrucciónes y la información de seguridad deben estar comunicado en lengua del operador antes del uso.
• No seguir estas indicaciónes puede causar daños personales o materiales.
!
WARNING
To avoid crushing and related injuries:
neveR work on, under or around a load supported only by a hydraulic jack. ALWAYS use adequately rated jack stands.
SFA Companies
http://www.omegalift.com
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in China
23221C-M1 rev 07/09
SAFeTY And GeneRAL InFORMATIOn
Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any jack that appears damaged in any way, or operates abnormally shall be removed from service immediately. If the jack has been or suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer for list of authorized service centers). It is recommended that an annual inspection be done by qualified personnel.
Labels and Operator's Manuals are available from manufacturer.
PROdUCT deSCRIPTIOn
These Hydraulic Truck Jacks are designed to lift, but not support, rated capacity partial vehicle loads consisting of one end of a vehicle. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands.
!
NEVER use a hydraulic truck jack as a stand-alone device. After lifting, immediately support the lifted vehicle with a pair of appropriately rated jack stands.
PRePARATIOn
Assembly (see Replacement Parts pages 6-7 for reference to parts location & assembly sequence)
Assemble, align and insert the handle assembly and handle position bar into the handle sleeve, then tighten the bolt on handle sleeve to prevent accidental removal of handle while in use.
Before Use
1. Verify that the product and application are compatible, if in doubt call Omega Technical Service (888) 332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve (handle knob):
a. Clockwise until firm resistance is felt to further turning. This is the ‘ CLOSed’ release valve position used to
raise the load.
b. Counter-clockwise, but no more than 1 full turn from the closed position. This is the ‘ OPen’ release valve
position used to lower the load. The more you turn the release valve counter-clockwise, the faster the load
descends.
4. With ram fully lowered, remove the oil filler screw. Check oil level. Proper oil level should be just below the rim of the opening. Reinstall the oil filler screw.
5. Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve. Connect to air supply, then squeeze the lift control valve for 3 seconds to evenly distribute lubricant.
note: These models are equipped with the popular 1/4" NPT air coupler. When installing a different air coupler of your choice, ensure that thread tape or compound is used when servicing connections. To ensure dependable, trouble free operation an inline air dryer and oiler is recommended.
6. Ensure that jack rolls freely. Raise and lower the unloaded ram throughout the lifting range before putting into service to ensure the jack operates smoothly. Replace worn or damaged parts and assemblies with Omega authorized replacement parts only.
Bleeding / venting Trapped Air
With the release valve in the OPEN position (3b.) and with ram fully lowered, locate and remove the oil filler screw.
This will help release any pressurized air which may be trapped within the reservoir. Reinstall the oil filler screw.
2
SPeCIFICATIOnS
Model Capacity Jack Size (L x W)
23221C
23222C
23301C
22 Ton
22 Ton
30 Ton
22-7/8" x 12-1/2"
22-7/8" x 12-1/2"
22-7/8" x 12-1/2"
Min.
Height
9-3/4"
8-1/4"
11"
Max.
Height
19-1/4"
16-3/4"
18"
Hyd.
Range
5-5/8"
4-5/8"
7"
Extension
Screw
3-7/8"
N/A
Handle
Handle Position
Release
Handle Knob
(release valve)
Handle Knob
(release valve)
Air Supply Inlet,
1/4NPT
Lift Control
Valve
Adapter, 5"
(23222C only)
Adapter, 2-1/2"
(23221C & 23222C)
Saddle
Air Supply Inlet,
1/4NPT
Handle Position
Release
Lift Control
Valve
Adapter Holder
(23221C & 23222C)
Handle Sleeve
Figure 1 - Typical Truck Jack Nomenclature (23222C shown)
Wheel
Extension Screw
(23221C & 23222C)
Oil Filler
Screw
Handle
Sleeve
Carrying
Handle
Handle
Saddle
Oil Filler Screw
(not shown)
Wheel
Carrying
Handle
Figure 1 - Model 23301C Nomenclature
3
!
WARNING
• Study, understand, and follow all printed materials provided with/on this product before use.
• do not exceed rated capacity.
• This is a lifting device only!
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
• Use only on hard, level surface.
• Lift only on areas of the vehicle as specified by the vehicle manufacturer.
• never wire, clamp or otherwise disable the lift control valve to function by other than operator's hand.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
!
WARNING
X
To avoid crushing and related injuries:
• never work on, under or around a load supported only by hydraulic jack.
• Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• do not use this device to lift, level, lower, support nor move a house, mobile home, travel trailer, camper or any building structure.
• Be alert and sober when using this product. Do not operate under the influence of drugs or alcohol.
!
The wheels provided with this jack are for positioning the jack under a load ONLY! The wheels are
not load wheels. Do not try to dolly or move the vehicle with the jack!
OPeRATIOn
(see Fig 1)
Lifting
note: The jack is equipped with handle position lock. To adjust the handle, release lock device by pulling the lever up, lever is spring loaded and will lock into desired position. Ensure lever locking mechanism is fully engaged before leaving
1. Connect adequate air source to the air supply inlet.
2. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement.
3. Close the release valve by turning the handle knob clockwise until firm resistance is felt.
4. Center jack saddle under lift point, then squeeze the lift control valve until saddle contacts the lift point. To lift, continue squeezing the lift control valve until load reaches desired height. Simply release your grip on the lift control valve to end lift event.
5. Transfer the load immediately to appropriately rated jack stands.
!
Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the vehicle as specified by the vehicle manufacturer.
!
NEVER use hydraulic jack as a stand alone device! ALWAYS transfer the lifted load IMMEDIATELY to a pair of appropriately rated jack stands. Use one pair of jack stands per vehicle. Rated capacity is per pair only! Do not exceed rated capacity.
Lowering
!
of the rate of speed at which the load lowers at all times!
Slowly open the release valve! The
more you turn the handle knob counter-clockwise, the faster the load will come down. Maintain control
1. Raise load high enough to clear the jack stands.
2. Remove jack stands carefully ( always used in pairs).
3. Slowly turn handle knob counter-clockwise, but no more than 1 full turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the malfunctioning jack and then the jack stands.
c. Use the functioning jack to lower the vehicle.
4. After removing jack from under the vehicle, fully retract the jack to reduce ram exposure to rust and contamination.
4
MAInTenAnCe
Important: Use only good grade hydraulic jack oil. Avoid mixing different types of fluid and NEVER use brake fluid, turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load. We recommend Mobil DTE 13M or equivalent.
Adding/ Changing Oil
For best performance and longest life, replace the complete fluid supply at least once per year.
1. With saddle fully lowered remove cover plate, then oil filler screw.
2. Lay jack on its side and drain fluid into a suitable container.
note: Dispose of hydraulic fluid in accordance with local regulations.
3. Set jack in its upright, level position.
4. Fill with oil. Proper oil level is just below the rim of the opening. Reinstall the oil filler screw.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that wheels move freely and the pump functions smoothly. To help ensure trouble free operation, an inline air dryer and oiler is recommended.
Cleaning
Periodically check the ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth.
note: Never use sandpaper or abrasive material on ram surfaces!
Storage
When not in use, store the jack with saddle fully lowered.
RePLACeMenT PARTS
(see pages 6 & 7)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, please give the Model number, part number and parts description. Call or write for current pricing: SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
E-Mail: [email protected] Tel: (888) 332-6419 Fax: (816) 891-6599 Omega Website: http://www.omegalift.com
TROUBLeSHOOTInG
Symptom
Jack will not lift load
Jack will lift, but not maintain pressure
Possible Causes
• Release valve not tightly closed
• Load is too heavy
• Air supply inadequate
• Release valve not tightly closed
• Hydraulic unit malfunction
Jack will not lower after unloading • Reservoir overfilled
• Linkages binding
Corrective Action
• Ensure release valve tightly closed
• Consider higher capacity jack
• Ensure adequate air supply
• Ensure release valve tightly closed
• Discontinue use, contact Omega technical service
• Drain fluid to proper level
• Clean and lubricate moving parts
Poor lift performance
Will not lift to full extension
• Fluid level low
• Air trapped in system
• Fluid level low
• Ensure proper fluid level
• With ram fully retracted, remove oil filler screw to let pressurized air escape. Reinstall oil filler screw
• Ensure proper fluid level
5
Replacement Parts for models 23221C & 23222C:
Item Part No.
Description Qty
1 A070-70000-100 Handle Assembly
2 G251-00007-000 Handle Grip
3 G251-40001-000 Knob
4 5402-04028-000 Spring Pin
5 5115-10017-000 Bolt
6 5303-00010-100 Washer, Lock
7 A070-00006-000 Handle Sleeve
8 A090-00001-000 Cover Plate
9 5110-06010-000 Screw
10 A070-00001-000 Wheel
11 5308-00013-006 Washer
12 5304-00013-000 C-clip
13 G831-03200-000 Air Motor
14 5102-10025-000 Bolt
15 5308-00095-000 Copper Gasket
16 A220-01000-000 Air Hose Assembly
1
1
1
4
2
2
4
2
1
1
1
5
1
1
1
2
17 A20060-0006
18 A20060-0007
Air Hose
Lift Control Valve
19 A20060-0016 Air Coupler, Male, 1/4
NPT
20 A070-3000-000 Release Valve Cable
21 A090-12008-000 Release Valve
1
1
1
1
1
3
16
Item Part No.
Description
22 5905-00054-000 Oil Seal
23 5105-05016-000 Screw
24 5102-08025-000 Screw
25 5202-00008-000 Nut
26 G62S-03301-000 Filler Screw
27 A070-00009-000 Spring
28 A070-11001-000 Extension Screw
29 A070-00007-000 Saddle
30 A070-00008-000 Spring Plate
31 A27010-0028
32 A0901S-077
33 A27010-0008
Air Filter
Repair Kit (includes
#22 & A~F)
Piston, Air Motor #13
34 A090-10000-000 Hydraulic Unit (for
23221C only)
35
A091-10000-000 Hydraulic Unit (for
23222C only)
A070-00003-000 Wheel Axle
36 A090-00002-000 Base Plate
37 A070-81001-000 Adapter Holder
38 A070-00015-000 Adapter, 2-1/2"
39 A091-00003-000 Adapter, 5" (for
23222C only)
1
1
1
2
1
1
4
1
2
1
Qty
1
1
2
1
-
1
1
1
29
30
19
2
39
1
38
4
17
28
25
18
31
37 27
A
B
24
5
7
15
C
6
8
26
F
B
9
13 33
6
22 E
14 21
23 D
36
35
11
10
12
34
20
B
Figure 2 - Replacement Parts Illustration for Model 23221C & 23222C
6
Replacement Parts for model 23301C:
8
9
6
7
4
5
2
3
Item
1
Part No.
Description
A070-70000-100 Handle Assembly
G251-00007-000 Handle Grip
G251-40001-000 Knob
5402-04028-000
5115-10017-000
16 A20060-0005
17 A20060-0006
18 A20060-0007
19 A20060-0016
Spring Pin
Bolt
5303-00010-000 Washer, Lock
A070-00006-000 Handle Sleeve
A300-00005-000 Cover Plate
5110-06010-000 Screw
10 A070-00001-000 Wheel
11 5308-00013-006 Washer
12 5304-00013-000 Retainer Clip
13 A27010-0021 Air Motor &14,15
14 A27010-0026 Washer
15 A27010-0027 Gasket
Lift Control Valve
Air Coupler, Male,
1/4 NPT
Qty
1
1
1
5
1
1
5
2
1
1
1
2
1
2
2
1
4
Air Hose Assembly 1
Air Hose 1
Item Part No.
Description
20 A070-30000-000 Release Valve
Cable
21 A300-13001-000 Release Valve
22 5905-00054-000 Oil Seal
23 5115-05012-000 Screw
24 BL80-15000-000 Hyd. Cartridge
25 B120-10003-000 Filter
26 G62S-03301-000 Filler Screw
27 A300-00003-000 Spring
28 5308-00380-000 Retaining Ring
29 B300-10003-000 Saddle
30 A300-00004-000 Spring Plate
31 A27010-0028 Air Filter
32 A300-90009-K01 Repair Kit (includes
#22, 26 & a~r)
33 A27010-0008 Internal Piston, Air
Motor
34 A300-90009-K02 Hydraulic Unit
35 A070-00003-000 Wheel Axle
Qty
1
1
1
2
2
1
1
1
1
1
1
1
1
-
1
1
30
2
27
4
3
18
19
34
1 16
17
31 r e
25 k m n o p
6
5
7
8
6
9
5
15
14
13 33 g
20
24
23 h i
21 j
22
35 11
12
10
Figure 3 - Replacement Parts & Illustration for Model 23301C
7 q f
29
28 a c d b
26
One YeAR LIMITed WARRAnTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419 [email protected]

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Lifts vehicle loads
- 22 Ton capacity for 23221C & 23222C
- 30 Ton capacity for 23301C
- Air-powered operation
- Release valve for controlled lowering
- Includes wheels for positioning
- Recommended for use with jack stands
- One-year limited warranty
- Replacement parts available