Samsung HT-AS1 User manual

Digital Amplifier
Speaker System
HT-AS1
HT-AS1T
THIS APPLIANCE IS MANUFACTURED BY:
Instruction Manual
AH68-01942B
Safety Warnings
PREPARATION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Precautions
This symbol indicates “dangerous voltage” inside
the product that presents a risk of electric shock
or personal injury.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER (or BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
GB
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm). Make sure
the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely
from the power supply, remove the mains plug from the wall outlet, especially when left unused for a long period of time.
CAUTION : INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains
plug shall be readily operable.
CAUTION
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Wiring the Main Power Supply Plug (UK Only)
During thunderstorms, disconnect AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the
unit.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable from
the AC supply if the player malfunctions. Your player is not
intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait approximately
2 hours until the unit has reached room temperature before using.
The battery used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug
and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse
fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain
a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to
a main socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
2
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
3
Features
GB
Contents
PREPARATION
PREPARATION
Built-in Subwoofer
Built-in subwoofer in the amplifier enables you to enjoy rich bass sound without additional
subwoofer speaker.
Safety Warnings ..............................................................................................................2
Precautions......................................................................................................................3
Features ..........................................................................................................................4
Description ......................................................................................................................6
CONNECTIONS
Digital Amplifier Speaker
Connecting the Speakers ................................................................................................10
Connecting External Components ..................................................................................12
This product is a pure digital Amplifier Speaker that performs digital signal processing to
minimize signal distortion and loss.
OPERATION
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal
decoding technology that improves upon existing Dolby Pro Logic.
DTS (Digital Theater Systems)
DTS play backs 5.1 channel sound with less compression than Dolby
Digital for richer sound.
Before Using the Digital Amplifier Speaker .....................................................................14
Selecting Digital/Analog Input .........................................................................................16
Setting the Speaker Mode ...............................................................................................18
Setting the Speaker Listening Distance .........................................................................20
Setting Digital Input .........................................................................................................22
Setting DRC (Dynamic Range Compression) .................................................................24
Test Tone ........................................................................................................................26
Setting Speaker Level .....................................................................................................30
Dolby Pro Logic ll Mode..................................................................................................32
Dolby Pro Logic ll Effect .................................................................................................34
Setting Tone Control ........................................................................................................36
SFE Mode........................................................................................................................38
Stereo Mode ....................................................................................................................40
MISCELLANEOUS
SFE(Sound Field Effect) Using 24bit Audio DSP
Provides more realistic surround sound with normal stereo audio sources.
4
Convenient Functions......................................................................................................42
Operating TV with Remote Control..................................................................................44
Operating your DVD (VCR) with Remote Control............................................................46
Before Calling for Service................................................................................................48
Specifications ..................................................................................................................50
5
GB
Description
POWER button
PREPARATION
[ Rear Panel ]
[ Front Panel ]
VOLUME CONTROL
DVD OPTICAL DIGITAL
AUDIO INPUT JACK
POWER STANDBY Indicator
FUNCTION button
SETUP button
CD COAXIAL DIGITAL
AUDIO INPUT JACK
INPUT MODE button
SURROUND MODE button
SELECT (
,
) button
VCR AUDIO INPUT JACKS
CD AUDIO INPUT JACKS
DVD AUDIO INPUT JACKS
SUBWOOFER OUTPUT JACKS 1, 2
VCR AUDIO OUTPUT JACKS
DVD VIDEO INPUT JACK
MONITOR VIDEO OUTPUT JACK
VCR VIDEO INPUT JACK
VCR VIDEO OUTPUT JACK
FRONT SPEAKER TERMINALS
CENTER SPEAKER TERMINALS
SURROUND SPEAKER
TERMINALS
[ Display ]
LIVE SURROUND
INDICATOR
√√ Accessories œœ
DTS
INDICATOR
DOLBY
INDICATOR
L.PCM
INDICATOR
SPEAKER INDICATOR
DOLBY DIGITAL
INDICATOR
Remote Control
DOLBY PRO
LOGIC II
INDICATOR
6
User’s Manual
DIGITAL INDICATOR
FRONT DISPLAY
7
GB
Description (Con’t)
TV button
AMP button
Insert Remote Batteries
DVD button
VCR button
DIMMER button
POWER button
TV/VIDEO, FUNCTION button
CD button
NUMBER(0~9) buttons
PREPARATION
[ Remote Control ]
1
Remove the battery
cover in the direction
of the arrow.
2
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
VCR button
DVD button
SLEEP button
INPUT MODE OPTICAL button
TONE button
DRC button
INPUT MODE ANALOG button
INPUT MODE COAXIAL button
EXTERNAL DEVICE PLAYBACK button
MUTE button
VOLUME CONTROL button
CHANNEL button
Follow these precautions to avoid leaking or cracking batteries:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries.Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
Range of Operation of the Remote Control
MENU button
CROSS OVER button
TONE
OPTICAL COAXIAL ANALOG
The remote control can be used up to approximately 7 meters in a straight line. It can also be operated at
a horizontal angle of up to 30° from the remote control STOP
sensor.
PLAY
CUSOR/ENTER button
SUBWOOFER ON/OFF button
INFO button
(You can view TV,DVD information on the TV screen.)
STEREO button
SPK DISTANCE button
SUBWOOFER LEVEL button
MODE button
EFFECT button
CROSS OVER
TEST TONE button
SPK LEVEL button
SFE MODE button
SPK SELECT button
SUB WOOFER
ON/
OFF
8
SPK DISTANCE
SUB WOOFER
LEVEL
9
GB
Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
ACTIVE SUBWOOFER
(not supplied)
ACTIVE SUBWOOFER
(not supplied)
MAIN UNIT
HT-AS1
MAIN UNIT
HT-AS1T
FRONT (L)
PS-AF1T
FRONT (R)
PS-AF1T
FRONT (L)
PS-AF1
SURROUND (L)
PS-AR1
SURROUND (R)
PS-AR1
CENTER
PS-AC1
• If more bass is desired, you can
connect an additional active
subwoofer (not supplied) to the
Subwoofer 1or 2 port. Since the
signal on the Subwoofer 1and 2 ports
is not stereo, you will hear the same
mono bass sound regardless of the
port you connect to.
SYSTEM MODEL NAME : HT-AS1
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
SURROUND (R)
PS-AR1T
• The position of the Digital Amplifier/ subwoofer Speaker
is not so critical. Place it anywhere you like.
Front Speakers
• Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
• Place the speakers so that their tweeters will be at
the same height as your ear.
• Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
Center Speaker
SURROUND (L)
PS-AR1T
CENTER
PS-AC1T
SYSTEM MODEL NAME : HT-AS1T
PS-AF1
PS-AC1
PS-AR1
Position of Digital Amplifier/
subwoofer Speaker
CONNECTIONS
FRONT (R)
PS-AF1
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
Surround Speakers
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they
face each other.
• Place them about 60 to 90cm (2 to 3feet) above your ear,
facing slightly downward.
PS-AF1T
PS-AC1T
PS-AR1T
√ Connecting Speaker Wire
1
Press the tab of the
speaker connector.
2
Insert the black wire into the black(-)
terminal and the gray wire into the
red(+) terminal.
❈ Unlike the front and center speakers, the surround
speakers are used to handle mainly sound effects and
sound will not come from them all the time.
• Never touch speaker terminals while the power is on.
Doing so could result in electric shock.
• Make sure the polarities (+ and -) are correct.
• It is best to install it at the same height as the front
speakers.
• You can also install it directly over or under the TV.
10
11
GB
Connecting External Components
Connecting Video Component
Connecting Audio Component
CONNECTIONS
CD Player
DVD Player
DVD Player
VCR
TV
• Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
• In a DVD/CD player, you can select one digital audio input from OPTICAL and COAXIAL.
12
13
GB
Before Using the Digital Amplifier Speaker
Turning On/Off
REMOTE CONTROL
1 Connect the power plug to the outlet.
2 Press AMP button to set the remote to Amplifier mode.
3 Press the POWER button of the remote control.
• This unit will be turned on or set to Standby mode.
To Select the Function
REMOTE CONTROL
Method 1
Press the FUNCTION button.
• Each time you press the this button, DVD ➝ VCR ➝ CD will be selected
in turn.
Method 2
Press CD, VCR or DVD button.
• You can directly select CD, VCR or DVD .
1 Connect the power plug to the outlet.
2 Press the POWER button of the main unit.
• This unit will be turned on or set to Standby mode.
OPERATION
MAIN UNIT
MAIN UNIT
Press FUNCTION button.
• Each time you press the this button, DVD ➝ VCR ➝ CD will be selected
in turn.
Functions of Dedicated Remote Control
You can operate your AMP, TV, DVD, VCR with one remote control.
See pages 44-47 for more details.
14
15
GB
Selecting Digital/Analog Input
You can listen to sound in 2 channel analogue or Dolby Digital or DTS using this unit.
REMOTE CONTROL
For DVD Function
Press the OPTICAL or COAXIAL button.
• DVD OPTICAL or COAXIAL will be selected.
• Only the items set in the DIGITAL IN of SETUP will be available.
or
Press the ANALOG button.
MAIN UNIT
For DVD Function
• DVD ANALOG will be selected.
Press the INPUT MODE button.
OPERATION
• DVD OPTICAL or COAXIAL and DVD ANALOG will be selected repetitirely.
For CD Function
Press the OPTICAL or COAXIAL button.
• CD OPTICAL or COAXIAL will be selected.
• Only the items set in the DIGITAL IN of SETUP will be available.
For CD Function
Press the INPUT MODE button.
• CD OPTICAL or COAXIAL and CD ANALOG will be selected repetitirely.
or
Press the ANALOG button.
• CD ANALOG will be selected.
• You can change the digital input setting for DVD and CD functions in the
“DIGITAL IN” setup. (See pages 22~23)
• You can enjoy Dolby Digital or DTS if you connect the digital audio output
jack of an external audio component to the optical/coaxial digital audio input
jack on the main unit.
16
17
GB
Setting the Speaker Mode
Signal outputs and frequency response from the speaker will be adjusted according to your speaker configuration
and whether certain speakers are used or not.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
MAIN UNIT
button to select the “SPK SETUP”, and then
2 Press
press ENTER button.
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
button to select the speaker you want.
3 Press
Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SWSPK ➝
CROVR will be selected in turn.
…† button to set the mode (Large, Small etc.)
4 Press
for the selected speaker.
OPERATION
2 Press FUNCTION button to select the “SPK SETUP”.
3 Press SURROUND MODE button to select the speaker
•
you want.
• Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SWSPK ➝
CROVR will be selected in turn.
5 Repeat steps 3-4 to set the mode for each speaker.
SELECT ( , ) button to set the mode
4 Press
for the selected speaker.
To exit setup mode
• Wait for about 5 seconds or press MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
5 Repeat steps 3-4 to adjust each speaker.
Using the SPK SELECT button
1 Press SPK SELECT button to select the speaker you want.
To exit setup mode
• Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SWSPK ➝
• Wait for about 5 seconds or press SETUP button.
CROVR ➝ SPK MODE OFF will be selected in turn.
“SETUP OFF” appears on the display and Setup Mode is exited.
2 Press …† button to set the mode (Large, Small etc.)
for the selected speaker.
3 Repeat steps 1-2 to set the mode for each speaker.
To turn the SUBWOOFER on or off.
Press SUBWOOFER ON/OFF button on the remote.
• Each time you press this button, SWSPK : YES, SWSPK : NO will be selected
in turn.
• If FRONT is set to LARGE, you can select YES or NO for SWSPK.
• If FRONT is set to SMALL, SWSPK is automatically set to YES.
NO cannot be selected.
To set the cross over.
18
Press CROSS OVER button, and then press …† button
to set the cross over frepuency.
Setting the Speaker
SPEAKER
F.SPK(Front)
C.SPK(Centre)
S.SPK(Surround)
SWSPK(Subwoofer)
CROVR
(Crossover Frequency)
Possible Settings
LARGE,SMALL
LARGE,SMALL,NONE
LARGE,SMALL,NONE
YES,NO
60,80,100,120,
150,180,200(Hz)
Default Setting
SMALL
SMALL
SMALL
YES
150Hz
• LARGE : Select when using large speakers. You can listen to full
range sound.
• SMALL : Select this when using small speakers
• NONE : Select when you use no speaker.
• YES (subwoofer) : Select when using the subwoofer speaker.
• NO (subwoofer) : Select when not using the subwoofer speaker.
• CROVR : Select the crossover frequency for the best bass
response in your room.
19
GB
Setting the Speaker Listening Distance
If the speakers cannot be placed at equal distances from the listening position, you can adjust the
delay time of the audio signals from the centre and surround speakers.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
MAIN UNIT
2 Press
button to select the “DIST SETUP”, and then
press ENTER button.
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
button to select the speaker you want.
3 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
•
•
…† button to set the speaker distance.
4 Press
For F.L, CEN, F.R, S.R, S.L, S.W Speaker, you can set the distance from the
•
OPERATION
2 Press FUNCTION button to select the “DIST SETUP”.
3 Press SURROUND MODE button to select the speaker
will be selected in turn.
you want.
speaker to listening position between 0.3~9.0m in intervals of 0.3m.
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝
To exit setup mode
S.W will be selected in turn.
• Wait for about 5 seconds or press MENU button.
SELECT( , ) button to set the speaker distance.
4 Press
For F.L, CEN, F.R, S.R, S.L, S.W Speaker, you can set the distance from the
“SETUP OFF” appears on the display and Setup Mode is exited.
•
Using the SPK DISTANCE button
speaker to listening position between 0.3~9.0m in intervals of 0.3m.
1 Press the SPK DISTANCE button to select the speaker you
want.
To exit setup mode
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W ➝
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and Setup Mode is exited.
DISTANCE OFF will be selected in turn.
2 Press …† button to set the speaker distance.
• For F.L, CEN, F.R, S.R, S.L, S.W Speaker, you can set the distance from
the speaker to listening position between 0.3~9.0m in intervals of 0.3m.
3 Repeat steps 1-2 to set the mode for each speaker.
• If the listening position is beyond the range of speaker distance setup
when you place the speaker, set the speaker distance to the maximum.
20
Setting Speaker Distance
Set the distance from the speaker to listening position in intervals of 0.3m.
• F.L (front left) : 0.3m ~ 9m
• CEN (centre) : 0.3m ~ 9m
• F.R (front right) : 0.3m ~ 9m
• S.R (surround right) : 0.3m ~ 9m
• S.L (surround left) : 0.3m ~ 9m
• SW (subwoofer) : 0.3m ~ 9m
21
GB
Setting Digital Input
You can set the digital input for a DVD/CD player to either OPTICAL or COAXIAL.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2 Press
button to select the “DIGITAL IN”, and then
press ENTER button.
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
•
…† button to set the digital input.
4 Press
Each time you press this button, COAXIAL
OPTICAL will be selected
•
in turn.
To exit setup mode
• Wait for about 5 seconds or press MENU button.
2 Press FUNCTION button to select the “DIGITAL IN”.
SURROUND MODE button to select the CD or
3 Press
DVD function.
• Each time you press this button, CD
4 Press SELECT(
,
OPERATION
button to select the the CD or DVD function.
3 Press
Each time you press this button, CD
DVD will be selected in turn.
DVD will be selected in turn.
) button to set the digital input.
• Each time you press this button, COAXIAL
OPTICAL will be selected
in turn.
“SETUP OFF” appears on the display and Setup Mode is exited.
To exit setup mode
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and the unit Setup Mode is exited.
• You can select only one digital input for each function.
Example) If you have selected COAXIAL for the CD function,
you cannot select COAXIAL for the DVD function.
Function
DVD
CD
22
Digital input (Default setting)
OPTICAL
COAXIAL
23
GB
Setting DRC (Dynamic Range Compression)
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2 Press
button to select the “DRC SETUP”, and
then press ENTER button.
• “DRC:STD” appears on the display.
•
will be selected in turn.
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2 Press FUNCTION button to select the “DRC SETUP”.
SURROUND MODE button.
3 Press
“DRC : STD” appears on the display .
OPERATION
…† button to set the DRC.
3 Press
Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN
MAIN UNIT
•
To exit setup mode
• Wait for about 5 seconds or press MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
4 Press SELECT(
,
) button to set DRC.
• Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN
will be selected in turn.
To exit setup mode
Using the DRC button
Press DRC button.
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and the unit Setup Mode is exited.
• Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN will be
selected in turn.
Setting DRC
• STD : Sets DRC effect to standard.
• MAX : Sets DRC effect to maximum.
• MIN : Sets DRC effect to minimum.
24
25
GB
Test Tone
Use test tone to check the speaker connection status or level.
To automatically output test tone
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
MAIN UNIT
•
button to select the “TEST-T AUTO”,
2 Press
and then press ENTER button.
S.R ➝ S.L ➝ S.W .
• During test signal output, press …† button to adjust the speaker output level
from -10 to +10 dB by 1 step.
•
2 Press FUNCTION button to select the “TEST-T AUTO”.
3 Press SURROUND MODE button.
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝
S.R ➝ S.L ➝ S.W .
To stop test tone
• During test signal output, press SELECT (
,
) button to adjust the speaker
output level from -10 to +10 dB by 1 step.
• Press MENU button once time.
“SETUP OFF” appears on the display and test tone stops.
To stop test tone
• Press SETUP button once time.
“SETUP OFF” appears on the display and test tone stops.
Using the Test Tone button
Press TEST TONE button.
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝ S.R ➝
S.L ➝ S.W.
• During test tone output, press …† button to adjust the speaker output level from
-10 to +10 dB by 1 step.
26
27
OPERATION
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
GB
Test Tone (Con’t)
Use test tone to check the speaker connection status or level.
To Manually Output Test Tone
√
REMOTE CONTROL
MAIN UNIT
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2
SETUP button.
1 Press
“SETUP MODE” appears on the display and the unit goes into Setup Mode.
Press
button to select the “TEST-T MANU”,
and then press ENTER button.
2 Press FUNCTION button to select the “TEST-T MANU”.
3 Press SURROUND MODE button.
button to select the speaker you want.
button, F.L ➝ CEN ➝ F.R ➝ S.R ➝
S.L ➝ S.W will be selected in turn.
• Each time you press
OPERATION
3 Press
•
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
will be selected in turn.
…† button to set the test tone as you want.
4 Press
You can adjust the speaker output level from -10 to +10dB by 1 step.
4 Press SELECT(
•
• The sound gets quieter at -10dB and louder at +10dB.
,
) button to set the test tone as you
want.
• You can adjust the speaker output level from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
To stop test tone
To stop test tone
• Press MENU button once time.
• Press SETUP button once time.
“SETUP OFF” appears on the display and test tone stops.
“SETUP OFF” appears on the display and test signal stops.
Test Tone Output
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
28
29
GB
Setting Speaker Level
You can set the balance and level of speakers.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
MAIN UNIT
button to select the “LEVEL SETUP”, and
2 Press
then press ENTER button.
3 Press
1 Press SETUP button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
button to select the speaker you want.
• Each time you press
4 Press …† button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
OPERATION
2 Press FUNCTION button to select the “LEVEL SETUP”.
SURROUND MODE button.
3 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
will be selected in turn.
•
• The sound gets smaller at -10dB and louder at +10dB.
will be selected in turn.
4 Press SELECT(
To exit setup mode
,
) button to set the speaker level
you want.
• Wait for about 5 seconds or press MENU button.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets smaller at -10dB and louder at +10dB.
“SETUP OFF” appears on the display and Setup Mode is exited.
To exit setup mode
Using the SPK LEVEL button
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and exits Setup Menu.
1 Press SPK LEVEL button to select the speaker you want.
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W ➝
SPK LVL OFF will be selected in turn.
2 Press …† button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
To set the SUBWOOFER LEVEL.
Press SUBWOOFER LEVEL button, and then press …†
button to set the subwoofer level.
30
Setting Speaker Level
• F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
31
GB
Dolby Pro Logic ll Mode
This mode provides 5.1 channel sound from 2 channel sources
REMOTE CONTROL
Press
MODE button.
• Each time you press this button, CINEMA ➝ MATRIX ➝ GAME
➝ PRO LOGIC ➝ MUSIC will be selected in turn.
MAIN UNIT
1 Press SURROUND MODE button to select “DPLII”
mode.
• Each time you press this button, DPLII ➝ SFE ➝ STEREO will be
2 Press SELECT(
,
OPERATION
selected in turn.
) button.
) button, CINEMA ➝ MATRIX ➝
GAME ➝ PRO LOGIC ➝ MUSIC will be selected in turn.
• Each time you press SELECT (
) button, MUSIC ➝ PRO LOGIC ➝
GAME ➝ MATRIX ➝ CINEMA will be selected in turn.
• Each time you press SELECT (
To exit setup mode
To exit setup mode
• Wait for about 5 seconds.
• Wait for about 5 seconds.
Dolby Pro Logic ll mode
• MUSIC : Provides 5.1 channel surround sound to digital,
analogue or existing stereo sources such as CD, TAPE, TV and
stereo VCR.
• CINEMA : Adds realism to the movie soundtrack.
• MATRIX : You will hear 5.1 channel surround sound.
• GAME : Enhances the excitement of the game's sound.
• PRO LOGIC : You will experience a surround effect with just the
front left and right speakers.
32
• You cannot use Dolby Pro Logic ll mode for multi channel
signals such as Dolby Digital and DTS.
• Pro Logic works only for PCM audio signals with sampling
frequencies of 32KHz, 44KHz or 48KHz.
• Sound will not be output from surround back speaker if
PCM audio signal is mono.
33
GB
Setting Dolby Pro Logic ll Effect
This function works only in Dolby PRO LOGIC II MUSIC Mode.
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
2 Press
button to select the “
and then press ENTER button.
3
MODE”,
MAIN UNIT
Press
button.
SETUP button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
• Each time you press this button,
C-WIDTH ➝ DIMENSION ➝
PANORAMA will be selected in turn.
2 Press FUNCTION button to select the “DPLII MODE”.
SURROUND MODE button.
3 Press
Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA
Press …† button to set the
Dolby Pro Logic ll effect you
want.
OPERATION
4
•
•
will be selected in turn.
Press SELECT( , ) button to set the Dolby
4 Pro
Logic ll effect you want.
To exit setup mode
• Wait for about 5 seconds or press MENU button.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the
To exit setup mode
EFFECT button
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and Setup Mode is exited.
1 Press
2 Press
MODE button to select ‘MUSIC’ Mode.
EFFECT button.
• Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA
will be selected in turn.
3 Press …† button to select Dolby Pro Logic II effect you
want.
• C-WIDTH : You can set from 0 to 7.
• DIMENSION : You can set from -7 to +7.
• PANORAMA : You can set it ON or OFF.
Dolby Pro Logic ll effect
• C-WIDTH : This sets the width of the centre image. The higher the setting, the less sound comes
from the centre speaker.
• DIMENSION : Incrementally adjusts the sound field (DSP)from the front or surround.
• PANORAMA : This mode extends the front stereo image to include the surround speakers for an
34
exciting "wraparound" effect with side wall imaging.
35
GB
Setting Tone Control
This function allows setting up the tone quality of the front speaker.
√
REMOTE CONTROL
MENU button, and then press ENTER button.
1 Press
“SETUP MODE” appears on the display and goes into Setup Mode.
•
button to select the “TONE CONTROL”,
2 Press
and then press ENTER button.
3 Press
button.
• Each time you press this button, BASS ➝ TREBLE➝ TONE : OFF will be
…† button to set the tone control you want.
4 Press
You can adjust it from -6 to +6dB by 1 step.
•
• The sound gets smaller at -6dB and louder at +6dB.
To exit setup mode
• Wait for about 5 seconds or press MENU button.
1 Press SETUP button.
• “SETUP MODE” appears on the display and goes into Setup Mode.
2 Press FUNCTION button to select the “TONE CONTROL”.
SURROUND MODE button.
3 Press
Each time you press this button, BASS ➝ TREBLE ➝ TONE : OFF will be
•
selected in turn.
4 Press SELECT(
,
) button to set the tone control you
want.
• You can adjust it from -6 to +6dB by 1 step.
• The sound gets smaller at -6dB and louder at +6dB.
“SETUP OFF” appears on the display and Setup Mode is exited.
Using the TONE button
1 Press TONE button.
To exit setup mode
• Wait for about 5 seconds or press SETUP button.
“SETUP OFF” appears on the display and exits Setup Menu.
• Each time you press this button, BASS ➝ TREBLE ➝ TONE : OFF will be
selected in turn.
2 Press …† button to set the tone control you want.
• You can adjust it from -6 to +6dB by 1 step.
• The sound gets quieter at -6dB and louder at +6dB.
• Tone Control function is available only in the Stereo mode.
36
37
OPERATION
selected in turn.
• If it is set to TONE: OFF, the Tone Control function will be disabled.
MAIN UNIT
GB
SFE Mode
The SFE (Sound Field Effect) function uses 7 different DSP sound field effects to digitally simulate actual music
environments such as concert halls or cinemas.
REMOTE CONTROL
Press SFE MODE button.
• Each time you press this button, HALL ➝ THEATER ➝ ARENA ➝ CLUB ➝
DOME ➝ STADIUM ➝ CHURCH will be selected in turn.
MAIN UNIT
SURROUND MODE button to select ‘SFE’ Mode.
1 Press
Each time you press this button, DPLII ➝ SFE ➝ STEREO will be selected
•
in turn.
SELECT( , ) button.
2 Press
Each time you press Select (
) button, HALL ➝ THEATER ➝ ARENA ➝
•
CLUB ➝ DOME ➝ STADIUM ➝ CHURCH will be selected in turn
) button, CHURCH ➝ STADIUM ➝
DOME ➝ CLUB ➝ ARENA ➝ THEATER ➝ HALL will be selected in turn.
• Each time you press Select (
To exit setup mode
• Wait for about 5 seconds.
To exit setup mode
• Wait for about 5 seconds.
38
39
GB
Stereo Mode
You can select this mode when listening to sound through the front left and right speakers and subwoofer.
For Surround Mode and Input Signal
o = active, – = inactive
Output Channel
Surround Mode
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PROLOGIC)
Input Signal
Decoding
Display Information
SL
Sub
SR Woofer
L/R
C
O
O
O
Display Signal Format
Channel Status
Dolby D Surr. EX
Dolby Digital 5.1
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (5.1ch)
Dolby Digital 5.1
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch)
Pro Logic II
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
Pro Logic II
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
L.PCM (Audio)
Pro Logic II
O
O
O
O
L.PCM
L, C, R, SL, SR, SW
Analog
Pro Logic II
O
O
O
O
ANALOG
L, C, R, SL, SR, SW
DTS-ES
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
DTS 96/24
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
DTS (5.1)
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
L.PCM (Audio)
Neo:6
O
O
O
-
L.PCM
L, R
Dolby D (2ch)
DD + SFE
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
DD + SFE
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
L.PCM (Audio)
SFE
O
O
O
O
L.PCM
L, C, R, SL, SR, SW
Analog
SFE
O
O
O
O
ANALOG
L, C, R, SL, SR, SW
Dolby D (2ch)
DD
O
-
-
-
DIGITAL
L, R, SW
Dolby D (2ch Surr)
DD
O
-
-
-
DIGITAL
L, R, SW
L.PCM (Audio)
Stereo
O
-
-
-
L.PCM
L, R, SW
L.PCM 96KHz
Stereo
O
-
-
-
L.PCM
L, R, SW
Analog
Stereo
O
-
-
-
ANALOG
L, R, SW
DTS
Press STEREO button.
• “STEREO” appears in the display and Stereo Mode is
selected.
MAIN UNIT
Press SURROUND MODE button to select
‘STEREO’.
SFE
• Each time you press this button, DPLII ➝ SFE ➝ STEREO will
be selected in turn.
STEREO
To exit setup mode
To exit setup mode
• Wait for about 5 seconds.
• Wait for about 5 seconds.
OPERATION
REMOTE CONTROL
L/R : Front Speaker (Left/Right) C : Center Speaker SL/SR : Rear Speaker (Left/Right) SW : Subwoofer
• Channel status displays are dependent on the speaker configuration.
• SFE mode works with 2-ch signals.
40
41
GB
Convenient Functions
Sleep timer function
You can set the time that this unit will shut itself off.
REMOTE CONTROL
Press the SLEEP button.
• SLEEP : OFF ➝ 15 ➝ 30 ➝ 45 ➝ 60 ➝ 90 ➝ 120 M (MIN) will be selected in turn.
To check sleep timer
Press SLEEP button.
• The remaining time before this unit will shut itself off is shown on the display.
• Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
• Press SLEEP button until “SLEEP : OFF” appears on the display.
Mute function
Reset function
If a product malfunction occurs, you can re-initialize the system.
REMOTE CONTROL
the MUTE button.
1 Press
MUTE appears on the display.
2 Press “0” button five times and then
•
press ENTER button.
• “INITIAL : YES” appears on the display.
…† buttons to select “YES”.
3 Press
The unit will turn off after 5 seconds.
•
MAIN UNIT
Turn off the power and hold the
SELECT( ) button for longer than
5 seconds.
• POWER STANDBY indicator will flash.
This function is useful when answering a doorbell or telephone call.
REMOTE CONTROL
Press the MUTE button.
Caution!
• Using the RESET function will erase all stored settings.
• Do not use this unless necessary.
• MUTE appears on the display.
Adjust the display
To output sound again
• MUTE will disappear and sound will output.
You can adjust the brightness of the display.
MISCELLANENOUS
Press MUTE button again.
REMOTE CONTROL
Press the DIMMER button.
• Each time you press this, the brightness changes as follows :
DARK ➝ BRIGHT.
• SLEEP, Mute and the Adjust Display function can only be
operated with the remote control.
42
43
GB
Operating your TV with the Remote Control
TV Brand Code List
Brand
1
Press TV button to set the remote
to TV mode.
2
Press POWER button to turn on the TV.
3
While holding down POWER button,
enter the code corresponding to your
brand of TV.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
4
ADMIRAL(M.WARDS)
A MARK
ANAM
AOC
BELL & HOWELL(M.WARDS)
BROCSONIC
CANDLE
CETRONIC
CITIZEN
CINEMA
CLASSIC
CONCERTO
CONTEC
CORONADO
CRAIG
CROSLEX
CROWN
CURTISMATES
CXC
DAEWOO
If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and
Numeric buttons (0~9).
DAYTRON
DYNASTY
EMERSON
• The remote control may not work on some brands of TVs. Also, some operations
may not be possible depending on your brand of TV.
• The remote control will work with Samsung TVs by default.
44
HALL MARK
HITACHI
INKEL
JC PENNY
JVC
KTV
KEC
KMC
LG(GOLDSTAR)
Brand
LUXMAN
LXI(SEARS)
MAGNAVOX
MARANTZ
MATSUI
MGA
MITSUBISHI/MGA
MTC
NEC
NIKEI
ONKING
ONWA
PANASONIC
PENNEY
PHILCO
PHILIPS
PIONEER
PORTLAND
PROTON
QUASAR
RADIO SHACK
RCA/PROSCAN
REALISTIC
SAMPO
SAMSUNG
SANYO
SCOTT
SEARS
SHARP
SIGNATURE 2000(M.WARDS)
SONY
SOUNDESIGN
SPECTRICON
SSS
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
040, 054
054
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
050, 051, 052, 053, 055,
101
003, 040
001
018
Brand
SYLVANIA
SYMPHONIC
TATUNG
TECHWOOD
TEKNIKA
TMK
TOSHIBA
VIDTECH
VIDECH
WARDS
YAMAHA
YORK
YUPITERU
ZENITH
ZONDA
DONGYANG
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
Code Number
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
003, 015, 018, 025
018, 040
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
054, 112
054
103
108, 109, 113, 119, 120,
121
108
108
113
113
113
114
114
114
114
114
114
114
114
114
116
MISCELLANENOUS
FISHER
FUNAI
FUTURETECH
GENERAL ELECTRIC(GE)
Code Number
056, 057, 058
001, 015
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
001, 018, 040, 048
057, 058, 081
059, 060
018
003
003, 018, 025
097
003
018
046
015
003, 005, 061, 082, 083,
084
062
003
059, 061, 063
003
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
040
003
003, 015, 040, 046, 059,
061, 064, 082, 083, 084,
085
019, 065, 103
003
003
006, 040, 056, 059, 066,
067, 068
040
015, 018, 050, 059, 069
045
056, 059, 067, 086
070
059, 061, 087, 088
003, 015, 040
015
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
45
GB
Operating your DVD (VCR) with the Remote Control
VCR Brand Code List
Brand
1
2
3
Press DVD button to set the remote to
DVD mode.
• If you operate VCR, press VCR button to set the remote to VCR mode.
Press POWER button to turn on the DVD
(VCR).
While holding down POWER button, enter
the code corresponding to your brand of
DVD (VCR).
• If there is more than one code listed for your DVD (VCR) in
the table, enter one at a time to determine which code works.
4
ADMIRAL(M.WARDS)
AWIA
AKAI
ANAM
AOC
AUDIO DYNAMIC
BELL & HOWELL(M.WARDS)
BROKSONIC
CANON
CAPEHART
CITIZEN
CRAIG
CRITERION
CURTIS MATHES
DAEWOO
DAYTRON
DBX
EMERSON
FISHER
If the DVD(VCR) turns off, the setting is
complete.
• You can use DVD (VCR) POWER, VOLUME, PLAY, PAUSE,
STOP, SKIP, MENU and Numeric button (0~9).
FUNAI
GENERAL ELECTRIC(GE)
GO VIDEO
HARMAN KARDON
HITACHI
• The remote control may not work on some brands of DVD (VCR).
Also, some operations may not be possible depending on your brand of DVD (VCR).
• The remote control will work with Samsung DVD (VCR) by default.
JVC
KENWOOD
LG(GOLDSTAR)
LXI(SEARS)
MAGIN
MAGNAVOX
MARANTZ
MARTA
46
043, 106
044, 045, 046
088, 089, 090
001, 002, 003, 004, 005,
033
091
019, 047, 092
048, 093
092, 094, 095
001, 033, 049, 091
011
050
050, 072, 096
051
001, 031, 032, 033, 044,
091
006, 007, 008, 009, 010,
011, 012, 013, 014, 015,
016, 017, 018, 046, 051,
091
011
019, 047, 052, 092
025, 031, 032, 044, 046,
094, 095, 097, 098, 099
009, 048, 053, 054, 055,
100
044
001, 031, 032, 033, 056,
091
059, 060, 061
019
020, 021, 049, 054, 062,
100
051
001, 033, 049, 091
001, 033
025
047, 048, 052, 062, 091,
092
001, 033, 047, 052, 063,
064, 065, 092
047, 050, 052, 092
019, 020, 021, 022, 023,
024, 025, 026, 027, 028,
029, 030, 050
020, 025, 044, 048, 050,
053, 054, 055, 062, 100
072
001, 031, 032, 033, 049,
066, 067, 091
001, 019, 033, 047, 052,
092, 110
025, 050
Brand
MEI
MEMOREX
MINOLTA
MITSUBISHI/MGA
MTC
MULTITECH
NEC
OLYMPIC
OPTIMUS
ORION
PANASONIC
PENNEY
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
QUASAR
RICO
RCA/PROSCAN
REALISTIC
SAMSUNG
SANYO
SANSUI
SCOTT
SEARS
SHARP
SINGER
SIGNATURE 2000(M.WARDS)
SHINTOM
SONY
STS
SYLVANIA
SYMPHONIC
TANDY
Code Number
001, 033
001, 025, 033, 054, 091,
100
020, 021, 062
068, 069, 070, 101, 102
072
044, 057, 069
019, 047, 052, 057, 092
049, 091
101
103
001, 004, 033, 049, 067,
091, 107
019, 020, 072
001, 020, 021, 033, 062
001, 033, 046, 049, 091,
094
001, 030, 033, 049, 050,
066, 091
025
049
011
001, 033, 049, 067, 091,
107, 108
036
001, 020, 021, 031, 032,
033, 049, 051, 062, 066,
070, 091, 104
001, 009, 025, 033,
044, 048, 054, 091,
101, 105
000, 006, 031, 032, 057,
058, 071, 072, 073, 074,
075, 076, 077, 078, 079,
080, 081
008, 009, 046, 048, 050,
054, 058, 093, 100
092
006, 051, 054, 057, 069,
070, 100, 101
020, 021, 025
043, 105, 106
096
043, 044, 054, 100, 106
096
034, 035, 036, 037, 038,
039, 040, 041, 042,082,
083, 084, 085, 086
020
001, 033, 044, 049, 066,
091
044
009
Brand
TASHIRO
TATUNG
TEAC
TECHNICS
TEKNIKA
TOSHIBA
TOTEVISION
TAEKWANG
UNITECH
VECTOR RESEARCH
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code Number
050
047, 052, 092
044, 047, 052, 092
001, 033, 049, 091
001, 025, 033
006, 051
025, 072
087
072
019
019
072
001, 020, 031, 032, 033,
043, 050, 054, 072, 100,
105, 106, 109
019, 047,048, 052, 092,
019, 047,048, 052, 092
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
MARANTZ
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
004, 018
009, 033
004, 024
026
028
029
030
031
MISCELLANENOUS
HQ
INSTANT REPLAY
JCL
JCP
JC PENNY
Code Number
47
GB
Before Calling for Service
Check
Symptom
Can't turn it on.
It does not work when the
button is pressed.
• Is the power cord plugged into the outlet?
• Connect the power plug to the outlet.
Symptom
Can't select Dolby Pro
Check
• Is the input signal selected properly?
Logic ll mode.
• Is there static electricity in the air?
Remedy
• Select 2 channel Dolby Digital, PCM, and
Analogue input signal.
• Disconnect the power plug and connect it
again.
• Are the speakers and external
•
Sound is not produced.
Remedy
•
•
•
components connected properly?
Is the Mute function on?
Is the volume set to minimum?
Is the speaker setup set incorrectly to
NONE?
Aren't you playing MPEG II audio in
an external device?
• Connect them correctly.
• Press Mute button to cancel the function.
There is no sound when
playing a DTS encoded
DVD.
• Is Digital input selected?
• Check whether digital external component
is properly connected and refer to page
22~23 to select the digital input.
• Adjust the volume.
• Refer to pages 18~19 to select LARGE,
SMALL or YES.
• MPEG II audio decoding is not supported.
Set the audio format of the external device
to PCM.
Product protection function
Picture does not appear when
the function is selected.
• Is the external component connected
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Are the left/right speaker or left/right
input/output cables connected
properly?
• Is the surround speaker connected
• Replace with new batteries.
• Operate at close distance.
• Check the left/right channel and connect
Heat protection
• The protection function will come on if the main unit or power
transformer overheats.
"
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
- If there is no problem when you turn the unit on again after
turning it off, PROTECTION mark will disappear on the
display and the unit will work properly.
• If PROTECTION appears on the display,
check whether the speaker terminal is shorted
and then turn on the unit
it/them correctly.
MISCELLANENOUS
The sound from each
device is changed during
stereo playback.
• Connect them correctly.
properly?
• Refer to pages 10~11 to connect it properly.
properly?
There is no sound from
surround speakers.
• Is SURR (surround) incorrectly set to
NONE in speaker setup?
• Is surround mode selected to stereo?
There is no sound from
centre speaker
• Refer to pages 18~19 to select LARGE or
SMALL.
• Refer to pages 32~41 to select other
Surround Mode.
• Is the centre speaker connected properly?
• Refer to pages 10~11 to connect it properly.
• Is CEN (centre) incorrectly selected to
• Refer to pages 18~19 to select LARGE or
NONE in speaker setup?
• Is the surround mode selected to stereo?
SMALL.
• Refer to pages 32~41 to select other
Surround Modes.
48
49
GB
Specifications
HT-AS1
GENERAL
AMPLIFIER
FREQUENCY
RESPONSE
VIDEO
OUTPUT
Power Supply
AC 220-240V, 50/60 Hz
Standby Power Consumption
0.9W
Power Consumption
100W
Weight
13 kg
Dimensions (W x H x D)
270 x 450 x 520 mm
Operating Temperature Range
+5°C~+35°C
Operating Humidity Range
10%~75%
Rated Output
20Hz~20KHz/THD = 10%
Front Speaker(Left+Right)
4 Ω 100W/CH
Center Speaker
4 Ω 100W/CH
Surround Speaker(Left+Right)
4 Ω 100W/CH
Subwoofer Speaker
4 Ω 100W/CH
Input Sensitivity/Impedance
450mV/47kΩ
S/N Ratio(Analog Input)
80dB
Separation(1KHz)
60dB
Analog Input
20Hz~20KHz(±3dB)
Digital Input
20Hz ~44KHz(±3dB)
TV Format
NTSC/PAL
Input Level/Impedance
1Vp-p/75 Ω
Output Level/Impedance
1Vp-p/75 Ω
Video Frequency Response
5Hz to 10KHz(-3dB)
S/N Ratio
60dB
S
P
E
A
K
E
R
S
Speaker system
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
Front / Surround
4Ω
140Hz~20KHz
86dB/W/M
100W
200W
Front
Surround
Front
Surround
Center
4Ω
140Hz~20KHz
86dB/W/M
100W
200W
90 x 152 x 90 mm
90 x 152 x 90 mm
0.5kg
0.4kg
200 x 90 x 92 mm
0.6 Kg
HT-AS1T
S
P
E
A
K
E
R
S
Speaker system
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Front / Surround
4Ω
140Hz~20KHz
86dB/W/M
100W
200W
Front
Dimensions (W x H x D)
Surround
Front
Weights
Surround
Center
4Ω
140Hz~20KHz
86dB/W/M
100W
200W
90 x 1045 x 90 mm
(Stand base :
270)
90 x 152 x 90 mm
3.5kg
0.4kg
200 x 90 x 92 mm
0.6 Kg
MISCELLANEOUS
❈ S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES-17 filter.
50
51

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project