Samsung SP-47W3HF User manual

Add to my manuals
48 Pages

advertisement

Samsung SP-47W3HF User manual | Manualzz

ELECT

COLOUR

TELEVISION

SP43T6/48T6/54T6/62T6

SP47W3/55W3/65W3

Owner’s Instructions

Before operating the unit, please read this manual thoroughly, and retain it for future reference.

REMOTE CONTROL

ON-SCREEN MENUS

PERFECT FOCUS

PICTURE IN PICTURE

TELETEXT

(depending on the model)

ENG

ENG

Important Warranty Information Regarding Television

Format Viewing

S tandard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television viewing per week.

W ide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on non-expanded standard format television video and programming, should be limited to no more than 15% of the total television viewing per week.

A dditionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying any stationary images that exceed the above

guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On television models that offer picture sizing features, use these controls to view the different formats as a full screen picture.

B e careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a result of format selection and use, as well as other burned-in images, is not covered by your Samsung limited warranty.

2

Safety Instructions

Do not expose the television to extreme temperature conditions or to extreme humidity conditions.

Do not expose the television to direct sunlight and other sources of heat.

Do not expose the television to any liquids.

Never put objects of any kind into the television, and do not place a water-containing vessel on the television.

During a storm conditions (especially when there is lightning) unplug the television from the mains socket and aerial.

Do not step on or twist the power cord.

Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.

If the television is broken, do not try to repair it yourself. Contact qualified service personnel.

If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place.

Do not drop the remote control.

This device is not for use in industrial environments.

ENG

Caution

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

!

CAUTION:

TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT DAMAGE WHICH MAY

RESULT IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The lightning flash and arrow head within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.

The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.

!

The main voltage is indicated on the rear of the TV set and the frequency is

50 or 60Hz.

3

ENG

Contents

(continued)

PREPARING YOUR TELEVISION

Safety Instructions .........................................................................................

Caution ..........................................................................................................

Front Control Panels......................................................................................

Front or Side Connection Panels...................................................................

Rear Connection Panel .................................................................................

Infrared Remote Control ................................................................................

Inserting the Batteries in the Remote Control................................................

Connecting the Aerial (or Cable Television Network)....................................

Switching Your Television On and Off...........................................................

Placing Your Television in Standby mode .....................................................

Plug & Play Feature.......................................................................................

Adjusting Basic Convergence........................................................................

Using the Perfect Focus Feature...................................................................

Choosing Your Language..............................................................................

SETTING UP THE CHANNELS

Storing the Channels Automatically...............................................................

Storing the Channels Manually......................................................................

Skipping Unwanted Channels .......................................................................

Fine tuning Channel Reception .....................................................................

Sorting the Stored Channels .........................................................................

USING THE TELEVISION (continued)

Changing the Picture Standard .....................................................................

Selecting the Picture Format .........................................................................

Adjusting the Picture Settings........................................................................

Activation/Deactivation the Digital Noise Reduction Feature ........................

Setting the Blue Screen Mode.......................................................................

Using the Natural Scan Feature ....................................................................

Using the LNA (Low Noise Amplifier) Feature...............................................

Adjusting the Volume.....................................................................................

Changing the Sound Standard ......................................................................

Adjusting the Sound Settings ........................................................................

Extra Sound Settings (Auto volume/Melody).................................................

Setting the Dolby ProLogic ............................................................................

Selecting the Sound Mode (depending on the model) ..................................

Switching the Sound Off Temporarily ............................................................

17

18

19

20

21

12

12

13

14

15

16

10

11

8

9

6

7

3

3

26

26

27

28

29

30

30

22

22

23

24

24

25

25

4

Contents

USING THE TELEVISION

Setting the Sleep Timer .................................................................................

Setting and Displaying the Current Time.......................................................

Switching the Television On and Off Automatically .......................................

Setting up your Remote Control ....................................................................

Picture In Picture ...........................................................................................

USING THE TELETEXT FEATURE (depending on the model)

Teletext Feature ............................................................................................

Displaying the Teletext Screen......................................................................

Selecting Display Options..............................................................................

Selecting a Teletext Page..............................................................................

INFORMATION ON CONNECTIONS AND RECOMMENDATIONS FOR USE

Setting up your PC (depending on the model) ..............................................

Changing the Screen Size or Position of your PC.........................................

Connecting to the PC Input ...........................................................................

Connecting to the AV Input/Outputs ..............................................................

Connecting to the AV Input............................................................................

Connecting to the DVD Input.........................................................................

Connecting to the S-Video Input....................................................................

Connecting to the Audio Output ....................................................................

Viewing Picture From External Sources ........................................................

Automatic Degaussing to Remove Colour Patches.......................................

Trouble Shooting: Before Contacting Service Personnel ..............................

31

31

32

33

34

36

37

38

39

40

41

41

42

42

43

43

44

44

45

45

Symbols

☛ ➢

Press Important Note

ENG

5

ENG

Front Control Panels

The actual configuration on your TV may be different, depending on your model.

6 a) Source Selection b) Menu Display c) Previous Channel Selection d) Next Channel Selection e) Volume Decrease f) Volume Increase g) Temporary Sound Switch-Off h) Remote Control Sensor i) Power j) Stand by & Timer Indicator

Front or Side Connection Panels

The actual configuration on your TV may be different, depending on your model.

a a) Perfect Focus b) Video Input c) Audio Inputs (L, R) d) S-Video Input e) PC Input

ENG

7

ENG

Rear Connection Panel

The actual configuration on your TV may be different, depending on the model.

Option

R L

Option a) 75 Ω Coaxial connector for

Aerial/Cable network b) Audio/Video Input/Output c) S-Video Input d) Video Inputs e) Audio Inputs f) Audio/Video Monitor Outputs g) DVD Video Inputs h) DVD Audio Inputs i, j, k) Audio Outputs

(Dolby Pro logic)

8

Infrared Remote Control

Buttons and markings are subject to change.

AUTOMATIC SWITCH-OFF

PERFECT FOCUS

VCR/DVD FUNCTIONS;

(STOP/REWIND/PLAY/PAUSE/

FAST-FORWARD)

REMOTE CONTROL SETUP

PC DISPLAY CONTROL

(CHANGE THE POSITION OR

SIZE OF SCREEN)

TELEVISION STANDBY BUTTON

Power

AV-LINK VCR STOP (OPTION)

AV-LINK VCR RECORD (OPTION)

PIP FUNCTIONS;

PIP ON/SWAP/LOCATE/

SOURCE SELECTION (TV/VIDEO)/

SCAN/CHANNEL SELECTION (P ▲/)

INFORMATION DISPLAY

(MEGA-TELETEXT OPTION)

NUMERIC BUTTONS

ONE/TWO-DIGIT CHANNEL SELECTION

EXTERNAL INPUT SELECTION

NEXT CHANNEL/

TELETEXT NEXT PAGE

VOLUME DECREASE

TELETEXT SUB-PAGE

ON-SCREEN DISPLAY/

TELETEXT REVEAL

TELETEXT DISPLAY/MIX

DOLBY PRO LOGIC MENU DISPLAY

FASTEXT TOPIC SELECTION

SOUND EFFECT SELECTION

MAKE THE REMOTE CONTROL WORKS

FOR TV, PC (OPTION), CABLE,

DVD PLAYER

TUNER/CABLE NETWORK SELECTION

MENU DISPLAY/

PROGRAMME SELECTION BY NAME

CONTROL THE CURSOR IN THE MENU

VOLUME INCREASE

CHANGE CONFIRMATION

PREVIOUS CHANNEL/

TELETEXT PREVIOUS PAGE

PICTURE SIZE/TELETEXT SIZE

SOUND MODE SELECTION/

TELETEXT CANCEL

TEMPORARY SOUND SWITCH OFF

PICTURE EFFECT SELECTION

The performance of the remote control may be affected by bright light.

9

ENG

ENG

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when you :

Purchase the television.

Find that the remote control is no longer operating correctly.

1 Remove the cover of the remote control by pressing the symbol

( PRESS ) and pulling the cover in the direction of the arrow.

2 Insert batteries, taking care to respect the polarities:

+ on the battery with + on the remote control

on the battery with on the remote control

3

Replace the cover by pushing it in the direction of the arrow.

10

Connecting the Aerial (or Cable Television Network)

To view television channels correctly, a signal must be received by the set from one of the following sources:

An outdoor aerial

A cable television network

Plug the aerial or cable network input cable to the 75

Ω coaxial socket on the rear of the television.

Rear of TV

Cable

Television

Network

ENG

11

ENG

Switching Your Television On and Off

The mains lead is attached to the rear of the television.

1

Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the TV set and the frequency is 50 or 60Hz.

2 Press the “ I “ (ON/OFF) button on the front of the television.

Result: The Standby indicator lights up on the front panel.

3 Press the POWER button on the remote control to switch the television on.

Result: The programme that you were watching last is reselected automatically.

4 To switch your television off, press the “ I “ (ON/OFF) button again on the front of the television.

Placing Your Television in Standby mode

Your television can be placed in Standby mode, in order to reduce:

Power consumption

Wear of the cathode ray tube

The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

The television is placed automatically in Standby mode when you turn it on.

1 Press the POWER button on the remote control.

Result: The screen is turned off and the Standby indicator on the front of the television lights up.

2 To switch the screen back on, simply press the POWER button again on the remote control.

Do not leave your television in standby mode for long periods of time (when you are away on holiday, for example).

In this case, you should switch it off completely.

12

Plug & Play Feature

When the television is initially powered ON, three basic customer settings proceed automatically and subsequently: setting the language, channel and clock.

1

If the television is in Standby mode, press the POWER button on the remote control.

Result: The message PLUG & PLAY is displayed. It flickers for a little while and then the LANGUAGE menu is automatically displayed.

2 Move the joystick up or down to select required language. Press the MENU button to enter the language, and then the message

ANT. INPUT : CHECK is displayed.

If any language is not selected on the LANGUAGE menu, the

LANGUAGE menu will be displayed about 30 seconds later.

3 Make sure that the antenna is connected to the TV. And move the joystick left or right.

Result: The AUTO STORE menu is displayed.

4 Select your area by moving the joystick left or right. The following areas are available: ASIA/W.EUROPE - CIS/E.EUROPE - CHINA -

HONGKONG/UK - AUSTRALIA - NZ/INDONESIA - SOUTH AFRICA -

AMERICA .

5 To search the channels, select the SEARCH by moving the joystick up or down, and then move the joystick left or right (refer to

“Storing the Channels Automatically” on page 17). Press the

MENU button to skip.

Result: The TIME menu is displayed.

6 Move the joystick left or right to move to the hour or minute. Set the hour or minute by moving the joystick up or down (refer to “Setting and Displaying the Current Time” on page 31).

7 When you have finished, press the MENU button.

Result: The message ENJOY YOUR WATCHING is displayed, and then the channel which has been stored will be activated.

PLUG & PLAY

ANT. INPUT : CHECK

SELECT EXIT

AUTO STORE

AREA : ASIA/W.EUROPE

SEARCH : -/+

SELECT ADJUST EXIT

TIME

CLOCK : -- : -- AM

TIMER : OFF

SELECT ADJUST EXIT

ENJOY YOUR WATCHING

ENG

13

ENG

Adjusting Basic Convergence

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE

BLUE SCREEN : ON

SELECT ENTER EXIT

CONVERGENCE

MANUAL CONVERGENCE

RED √

BLUE √

PERFECT FOCUS √

SELECT ENTER EXIT

PLEASE USE REMOTE CONTROL

RED

POSITION 0:R/B

UP/DOWN L/R EXIT

If the color appears spread out or “smeared” on the screen, the convergence probably needs alignment. Be sure to use the remote control for the convergence adjustments. (The Convergence

Adjustment can not be made by using the control buttons on the front panel.)

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed.

3 Move the joystick up or down until the CONVERGENCE is selected and press the joystick ( ) button.

Result: The CONVERGENCE menu is displayed with the RED selected.

4 Press the joystick ( ) button again.

Result: A crosshair pattern will appear on the screen.

5 Adjust convergence by using your remote control.

If a horizontal red line is visible, use P and P buttons to move the line so that it is superimposed on the horizontal center-line (i.e., make a signal horizontal line that is as white as possible).

If a vertical red line is visible, use - and + buttons to move the line so that it is superimposed on the vertical center-line (i.e., make a signal vertical line that is as white as possible).

6 For blue adjustment, do the same as the above.

7 After the blue convergence is correctly adjusted, press the

MENU button repeatedly to return to normal viewing.

Since the center convergence adjustments can not be done after completing the side convergence adjustments, do the center convergence adjustments first.

14

Using the Perfect Focus Feature

When the picture size is distorted after moving the set, use the

Perfect Focus feature to adjust for the optimum picture size set in the factory.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed.

3 Move the joystick up or down until the CONVERGENCE is selected and press the joystick ( ) button.

Result: The CONVERGENCE menu is displayed.

4 Move the joystick up or down until the PERFECT FOCUS is selected and press the joystick ( ) button.

Result: Perform Perfect Focus in the following sequence: green

➞ red ➞ blue.

The Perfect Focus feature ends after the cursor flickers for one second.

5 Press the MENU button repeatedly to return to normal viewing.

You can use the Perfect Focus feature by simply pressing the PERFECT FOCUS button on the remote control.

◆ If any error happens during Perfect Focus, then perform Perfect Focus once again.

◆ If you can not make adjustments after Perfect Focus, then make manual adjustments. Still you can not make adjustments, contact your Service Center.

◆ If Perfect Focus operates by a wrong use of remote control, then press the MENU button to exit.

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE

BLUE SCREEN : ON

SELECT ENTER EXIT

CONVERGENCE

MANUAL CONVERGENCE

RED √

BLUE √

PERFECT FOCUS √

SELECT ENTER EXIT

PERFECT FOCUS

MODE ON

EXIT

ENG

15

ENG

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE

BLUE SCREEN : ON

SELECT ENTER EXIT

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE √

BLUE SCREEN : ON

SELECT ADJUST EXIT

Choosing Your Language

When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed with the LANGUAGE selected.

4 Select a particular language by moving the joystick left or right repeatedly.

5 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

You can choose only English according to location.

16

Storing the Channels Automatically

You can scan the frequency ranges available on your television and in your area and store all the channels found automatically.

The channels are stored in the order in which they appear in the frequency bands. It is possible that the automatically allocated numbers may not correspond to those by which you wish to identify the channels. If this is the case, refer to “Sorting the Stored

Channels” on page 21.

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the CHANNEL is selected and press the joystick ( ) button.

Result: The CHANNEL menu is displayed with the AUTO STORE selected.

3 Press the joystick ( ) button again.

Result: The AUTO STORE menu is displayed with the AREA selected.

4

Select your area by moving the joystick left or right. The following countries are available: ASIA/W.EUROPE - CIS/E.EUROPE -

CHINA - HONGKONG/UK - AUSTRALIA - NZ/INDONESIA - SOUTH

AFRICA - AMERICA.

5 Move the joystick up or down until the SEARCH is selected and move the joystick left or right.

Result: The horizontal bar is displayed, and then channels are stored in an order which reflects their positions in the frequency range. Finally, the search will end automatically.

6

When searching and storing is complete, the SORT menu is displayed.

To...

Then...

Sort the stored channels into the desired numerical order

Exit the channel store function without sorting the channels

Go to Step 4 of the “Sorting the Stored Channels” procedure on page 21.

Press the MENU button repeatedly until the menus disappear.

CHANNEL

AUTO STORE

MANUAL STORE √

ADD/ERASE

FINE TUNE √

SORT

SELECT ENTER EXIT

AUTO STORE

AREA : ASIA/W.EUROPE

SEARCH : -/+

SELECT ADJUST EXIT

AUTO STORE

AREA : ASIA/W.EUROPE

SEARCH : -/+

SELECT SEARCH EXIT

P 8 C--

426 MHz 22%

EXIT

FROM : P 1

TO : P--

STORE : ?

SORT

SELECT ADJUST EXIT

ENG

17

ENG

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : C12

STORE : ?

SELECT ADJUST EXIT

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : C12

STORE : ?

SELECT ADJUST EXIT

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : P12

STORE : ?

SELECT ADJUST EXIT

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : P12

STORE : ?

SELECT SEARCH EXIT

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : P12

STORE : ?

SELECT ADJUST EXIT

MANUAL STORE

COLOR SYSTEM : AUTO

SOUND SYSTEM : BG

SEARCH : 138MHZ

CHANNEL : C 6

PROG.NO. : P12

STORE : ?

SELECT ADJUST EXIT

18

Storing the Channels Manually

When storing channels manually, you can choose:

Whether or not to store each of the channels found.

The number by which you wish to identify each stored channel.

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the CHANNEL is selected and press the joystick ( ) button.

Result: The CHANNEL menu is displayed.

3 Move the joystick up or down until the MANUAL STORE is selected and press the joystick ( ) button.

Result: The MANUAL STORE menu is displayed with the COLOR

SYSTEM selected.

4 If necessary, indicate the broadcasting standard required by moving the joystick left or right.

Result: The color standards are displayed in the following order.

AUTO

PAL SECAM NT4.43 NT3.58

NT4.43

is a “trick” playback mode used by special

VCR’s to play PAL-recorded videos in NTSC mode.

5 Move the joystick up or down until the SOUND SYSTEM is selected and move the joystick left or right.

Result: The sound standards are displayed in the following order.

BG

DK I M

6 If you...

Know the number of the channel to be stored

Do not know the channel numbers

Move the joystick...

◆ up or down to select the CHANNEL.

◆ left or right to indicate the required required number.

◆ up or down to select the SEARCH.

◆ left or right to start the search.

Result: The tuner scans the frequency range until the first channel or the channel that you selected is received on your screen.

7 To assign a programme number to the channel, select the

PROG.NO.

. Move the joystick left or right until you find the correct number.

8

To store the channel and associated programme number, select the STORE and move the joystick left or right.

Result: OK is displayed.

9 Repeat Steps 6 to 8 for each channel to be stored.

10 When you have finished manual storage, press the TV button, or press the MENU button repeatedly to return to normal viewing.

Skipping Unwanted Channels

You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those you have chosen to skip are not displayed.

All channels that you do not specifically choose to skip are displayed during scanning.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the CHANNEL is selected and press the joystick ( ) button.

Result: The CHANNEL menu is displayed.

3

Move the joystick up or down until the ADD/ERASE is selected and press the joystick ( ) button.

Result: The ADD/ERASE menu is displayed.

4 Move the joystick up or down to select the required channel.

5

To add or erase the desired channel by moving the joystick left or right.

6

When you have finished adding and erasing channels, press the

TV button, or press the MENU button repeatedly to return to normal viewing

CHANNEL

AUTO STORE

MANUAL STORE √

ADD/ERASE

FINE TUNE √

SORT

SELECT ENTER EXIT

CHANNEL

AUTO STORE √

MANUAL STORE √

ADD/ERASE √

FINE TUNE √

SORT √

SELECT ENTER EXIT

P 0 : ADDED

P 1 : ADDED

P 2 : ADDED

P 3 : ADDED

ADD/ERASE

SELECT ADJUST EXIT

ADD/ERASE

P 0 : ERASED

P 1 : ADDED

P 2 : ADDED

P 3 : ADDED

SELECT ADJUST EXIT

ENG

19

ENG

CHANNEL

AUTO STORE

MANUAL STORE √

ADD/ERASE

FINE TUNE √

SORT

SELECT ENTER EXIT

TUNE : -/+

STORE : ?

ERASE : ?

FINE TUNE

SELECT ADJUST EXIT

FINE TUNE

Fine tuning Channel Reception

TUNE : -/+

STORE : OK

ERASE : ?

FINE TUNE

If the reception is clear, you do not have to fine-tune the channel, as this is done automatically during the search and store operation.

If however the signal is weak or distorted, you may have to finetune the channel manually.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the CHANNEL is selected and press the joystick ( ) button.

Result: The CHANNEL menu is displayed.

3

Move the joystick up or down until the FINE TUNE is selected and press the joystick ( ) button.

Result: The FINE TUNE menu is displayed with the TUNE selected.

4 To...

obtain a sharp and clear picture and good sound quality memorise adjusted picture or sound erase adjusted picture or sound

Move the joystick...

◆ left or right.

Result: The horizontal bar’s cursor moves to the left or right.

◆ up or down to select the STORE.

◆ left or right.

Result: OK is displayed.

◆ up or down to select the ERASE.

◆ left or right.

Result: OK is displayed.

5 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

SELECT ADJUST EXIT

TUNE : -/+

STORE : ?

ERASE : OK

FINE TUNE

SELECT ADJUST EXIT

20

Sorting the Stored Channels

You can exchange the numbers of two channels, in order to:

Modify the numeric order in which the channels have been automatically stored.

Give easily remembered numbers to the channels that you watch most often.

1 Press the MENU button.

Result: The main menu is displayed.

2

Move the joystick up or down until the CHANNEL is selected and press the joystick ( ) button.

Result: The CHANNEL menu is displayed.

3 Move the joystick up or down until the SORT is selected and press the joystick ( ) button.

Result: The SORT menu is displayed with the FROM selected.

4 Move the joystick left or right until the channel number that you wish to change is displayed.

Result: The selected channel’s picture is displayed.

5 Move the joystick up or down to select the TO.

6 Move the joystick left or right until the new number by which you wish to identify the channel is displayed.

7 To...

Move the joystick...

Confirm the exchange

◆ up or down to select the STORE.

of channel numbers

◆ left or right.

Result: OK is displayed.

The selected channel is exchanged with the one previously stored to the chosen number.

Example: If you select P 1 for the

FROM and P 3 for the TO:

◆ Channel 1 becomes channel 3.

◆ Channel 3 becomes channel 1.

You can exchange other channel numbers by selecting FROM and returning to step 4 .

8 When you have finished sorting channels, press the TV button, or press the MENU button repeatedly to return to normal viewing.

CHANNEL

AUTO STORE

MANUAL STORE √

ADD/ERASE

FINE TUNE √

SORT

SELECT ENTER EXIT

FROM : P 1

TO : P--

STORE : ?

SORT

SELECT ADJUST EXIT

FROM : P 1

TO : P 3

STORE : ?

SORT

SELECT ADJUST EXIT

From : P 3

To : P 1

Store : OK

Sort

SELECT ADJUST EXIT

ENG

21

ENG

PICTURE

MODE

œ √

ADJUST √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : OFF

SELECT ADJUST EXIT

PICTURE

MODE œ √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : OFF

SELECT ADJUST EXIT

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements. The following picture effects are available in the order given:

Natural, Mild, Custom, Standard, Sports.

1

Press the MENU button.

2

Press the joystick ( ) button to enter the PICTURE menu.

Result: The PICTURE menu is displayed with the MODE selected.

3

Select the required picture effect by moving the joystick left or right repeatedly.

4

When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

You can use your remote control to select the type of picture which best corresponds to your viewing requirements.

To select the required picture effect, simply press the P.STD standard) button on the remote control.

(Picture

Result: The following picture effects are available in the order given:

NATURAL

MILD CUSTOM STANDARD SPORTS

Selecting the Picture Format

You can select the picture format which best corresponds to your viewing requirements by simply pressing the “P.SIZE

” button.

The following picture formats are available (depending on the model);

NORMAL, WIDE, PANORAMA, ZOOM1, ZOOM2

NORMAL, ZOOM1, ZOOM2

Picture format cannot be changed in the PIP mode.

22

Adjusting the Picture Settings

Your television has several settings which allow you to control picture quality:

Color tone, Contrast, Brightness, Color,

Sharpness, Tint (NTSC only)

1 Press the MENU button.

2 Press the joystick ( ) button to enter the PICTURE menu.

3 Move the joystick up or down until the ADJUST is selected and press the joystick ( ) button

Result: The ADJUST menu is displayed with the current option.

When the MODE is set to CUSTOM, the ADJUST menu is displayed.

4 To adjust the...

COLOR TONE

Move the joystick...

◆ left or right until the required option is

(NORMAL, WARM1, WARM2, COOL1,

COOL2 ) displayed.

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT (NTSC only)

◆ left or right.

Result: The horizontal bar is displayed.

5

When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

The television has an “automatic degaussing” system that is activated if magnetic interference is present. To degauss the television screen, switch power off by pressing the “ I

(ON/OFF) button on the front panel (refer to “Automatic

Degaussing To Remove Colour Patches” on page 45).

If you make any changes to the ADJUST settings, the picture standard is automatically switched to CUSTOM.

PICTURE

MODE

œ √

ADJUST √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : OFF

SELECT ENTER EXIT

ADJUST

COLOR TONE : NORMAL

CONTRAST : 100

BRIGHTNESS : 50

SHARPNESS : 75

COLOR

TINT

: 60

: 50G 50R

SELECT ADJUST EXIT

ADJUST

COLOR TONE : NORMAL

CONTRAST : 100

BRIGHTNESS : 50

SHARPNESS : 75

COLOR

TINT

: 60

: 50G 50R

SELECT ADJUST EXIT

CONTRAST 100

ENG

23

ENG

PICTURE

MODE

œ √

ADJUST √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : OFF

SELECT ENTER EXIT

PICTURE

MODE œ √

ADJUST √

DIGITAL NR : OFF

NATURAL SCAN : ON

LNA : OFF

SELECT ADJUST EXIT

Activating/Deactivating the Digital Noise Reduction Feature

If the broadcast signal received by your television is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.

1 Press the MENU button.

2 Press the joystick ( ) button to enter the PICTURE menu.

3

Move the joystick up or down to select the DIGITAL NR.

4 Select the required option (ON/OFF) by moving the joystick left or right.

5 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

Setting the Blue Screen Mode

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE √

BLUE SCREEN : ON

SELECT ADJUST EXIT

If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background.

If you wish to continue viewing the poor picture, you must set the

“BLUE SCREEN” mode to “ON”.

1 Press the MENU button.

Result: The main menu is displayed.

2

Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed.

3 Move the joystick up or down to select the BLUE SCREEN.

4 Select the required option (ON/OFF) by moving the joystick left or right.

5

When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

24

Using the Natural Scan Feature

You will normally find that Natural scan is best set to on to reduce any slight picture flicker. However, it is possible that some occasional broadcasts may benefit by selecting the off position.

1 Press the MENU button.

Result: The main menu is displayed.

2

Move the joystick up or down until the PICTURE is selected and press the joystick ( ) button.

Result: The PICTURE menu is displayed.

3 Move the joystick up or down to select the NATURAL SCAN.

4 Select the required option (ON/OFF) by moving the joystick left or right.

5

When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

PICTURE

MODE

œ √

ADJUST √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : OFF

SELECT ADJUST EXIT

ENG

Using the LNA (Low Noise Amplifier) Feature

This function is very useful in the situation that the TV is used in weak signal. LNA amplifies the TV signal in the weak signal area, but not noise.

This function works only when a weak signal is received, and it keeps ON for the current channel even if you change the channel.

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the PICTURE is selected and press the joystick ( ) button.

Result: The PICTURE menu is displayed.

3

Move the joystick up or down to select the LNA.

4 Select the required option (ON/OFF) by moving the joystick left or right.

5 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

PICTURE

MODE œ √

ADJUST √

DIGITAL NR : ON

NATURAL SCAN : ON

LNA : ON

SELECT ADJUST EXIT

25

ENG

Adjusting the Volume

◆ Press the + button to increase the volume (cursor moves to the right)

◆ Press the button to decrease the volume (cursor moves to the left)

The volume setting is retained:

◆ When you switch the television to standby mode

◆ When you switch the television off using the

I ” (ON/OFF) button on the front panel

◆ If there is a power failure.

VOLUME 12

SOUND

MODE œ √

EQUALIZER

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ADJUST EXIT

SOUND

MODE

œ √

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ADJUST EXIT

Changing the Sound Standard

You can select the type of special sound effect to be used when watching a given broadcast. The following sound effects are available in the order given:

Standard, Music, Movie, Speech, Custom.

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the SOUND is selected and press the joystick ( ) button.

Result: The SOUND menu is displayed with the MODE selected.

3

Select the required sound effect by moving the joystick left or right repeatedly.

4 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

You can use your remote control to select the type of special sound effect to be used when watching a given broadcast.

To select the required sound effect, simply press the S.STD standard) button on the remote control.

(Sound

Result: The following sound effects are available in the order given:

STANDARD

MUSIC MOVIE SPEECH CUSTOM

26

Adjusting the Sound Settings

The sound settings can be adjusted to suit your personal preferences.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the SOUND is selected and press the joystick ( ) button.

Result: The SOUND menu is displayed.

3 Move the joystick up or down until the EQUALIZER is selected and press the joystick ( ) button.

Result: The EQUALIZER menu is displayed.

When the MODE is set to CUSTOM, the EQUALIZER menu is displayed.

5 Select the required option and adjust to satisfy your preference.

6 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

SOUND

MODE œ √

EQUALIZER √

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ENTER EXIT

EQUALIZER

R

L

100 300 1K 3K 10K

ADJUST MOVE EXIT

ENG

27

ENG

SOUND

MODE œ √

EQUALIZER √

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ENTER EXIT

SOUND

MODE œ √

EQUALIZER √

AUTO VOLUME : ON

MELODY : ON

DOLBY PRO LOGIC √

SELECT ADJUST EXIT

SOUND

MODE œ √

EQUALIZER √

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ADJUST EXIT

Extra Sound Settings

The following sound settings can be adjusted to suit your personal preferences.

AUTO VOLUME

Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the channel is changed. AUTO VOLUME lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

MELODY

You can hear clear melody sound when the TV is powered ON or OFF.

1 Press the MENU button.

Result: The main menu is displayed.

2

Move the joystick up or down until the SOUND is selected and press the joystick ( ) button.

Result: The SOUND menu is displayed.

3

To...

Move the joystick...

Change an option up or down.

Select the required option (ON/OFF) left or right.

4 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

28

Setting the Dolby ProLogic

You can enjoy Dolby prologic surround effect fully with only surround speakers are connected to TV.

This allows various modes for the main, center and rear speakers to be selected.

Surround Mode

NORMAL

PHANTOM

WIDE

Input Signal

Stereo

Mono

Stereo

Mono

Stereo

Mono

Stereo

Mono

Main

Speakers

Centre

Rear

OFF

; Sound

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the SOUND is selected and press the joystick ( ) button.

Result: The SOUND menu is displayed.

3 Move the joystick up or down until the DOLBY PRO LOGIC is selected and press the joystick ( ) button.

Result: The DOLBY PRO LOGIC menu is displayed with the

MODE selected.

4 Select the required mode (OFF, NORMAL, PHANTOM, WIDE) by moving the joystick left or right.

The following Dolby settings can be adjusted to suit your personal preferences.

Volume of the centre and rear speakers

Prologic delay time for the rear speakers (between

15 and 30 ms)

Activation/deactivation of the test tone to simulate the volume on each speaker

5 To...

Change a setting

Move the joystick...

up or down.

Change the option left or right.

6 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.

Rear of TV

Option

R L

SOUND

MODE œ √

EQUALIZER √

AUTO VOLUME : OFF

MELODY : ON

DOLBY PRO LOGIC √

SELECT ENTER EXIT

DOLBY PRO LOGIC

MODE œ √

SELECT ADJUST EXIT

DOLBY PRO LOGIC

MODE œ √

CENTER : 0

REAR : 0

DELAY : 20 ms

TEST TONE : OFF

CONNECT SPEAKER

SELECT ADJUST EXIT

DOLBY PRO LOGIC

MODE œ √

CENTER : 0

REAR : 0

DELAY : 20 ms

TEST TONE : OFF

CONNECT SPEAKER

SELECT ADJUST EXIT

29

ENG

ENG

Selecting the Sound Mode

(depending on the model)

The “S.MODE” button displays/controls the processing and output of the audio signal. When power is switched ON, the mode is automatically preset to either “Dual-I” or “Stereo”, depending on the current transmission.

NICAM

Stereo

Type of broadcast

Regular broadcast

(Standard audio)

Regular +

NICAM Mono

NICAM Stereo

NICAM Dual-I/II

On-screen indication

Mono (Normal use)

Mono

Mono

Nicam (Normal)

Stereo

Mono

Nicam (Normal)

Dual-I

Dual-II Mono

Nicam Nicam (Normal)

Regular broadcast

(Standard audio)

Mono (Normal use)

A2

Stereo

Bilingual or Dual-I/II

Stereo

Dual-I

Dual-II

Stereo

Mono

(Forced Mono)

◆ If the receiving conditions deteriorate, listening will be easier if the mode is set to the “Mono” position using the

S.MODE button.

◆ If the stereo signal is weak (or if intermittent Stereo-Mono) and automatic switching occurs, then switch to the

“Mono” mode.

◆ When receiving mono sound in the AV mode, connect to the “L” input jack on the panels. If the mono sound comes out only from the left speaker, then press the

S.MODE button.

Switching the Sound Off Temporarily

You can switch the sound off temporarily, for example you may wish to answer the telephone.

1 Press the MUTE button.

Result: The sound is switched off and “ ” is displayed.

2 When you wish to turn the sound back on at the same volume as before, press the MUTE button again (or either of the volume buttons).

30

Setting the Sleep Timer

You can select a time period of between 30 and 180 minutes after which the television automatically switches to Standby mode by pressing the “SLEEP ” button.

1 Press the SLEEP button on the remote control.

Result:

If the sleep timer is...

Already set

The screen displays...

Time remaining before the television will be placed in standby mode.

Not yet set Word OFF.

2

Press the SLEEP button repeatedly and cycle through the preset time intervals (30, 60, 90, 120, 150, 180).

Result: The television automatically switches to standby mode when the timer reaches 0.

3 To cancel the sleep timer function, press the SLEEP button repeatedly and select OFF.

Setting and Displaying the Current Time

You can set the television’s clock so that the current time is displayed when you press the “DISPLAY ” button. You must also set the time if you wish to use the automatic On/Off timers.

The clock will be re-set when pressing the “ I ” (ON/OFF) button on the front panel.

1 Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed.

3 Move the joystick up or down until the TIME is selected and press the joystick ( ) button.

Result: The TIME menu is displayed with the CLOCK selected.

4 To...

Move the joystick...

Move to the hour or minute

6 To display the...

left or right.

Set the hour or minute up or down.

5 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

Press the “DISPLAY ” button...

Channel information Once.

Current time Twice.

7 To remove the display, press the DISPLAY button again.

FUNCTION

LANGUAGE : ENGLISH

TIME √

CONVERGENCE

BLUE SCREEN : ON

SELECT ENTER EXIT

TIME

CLOCK : 11 : 35 AM

TIMER : OFF

SELECT ADJUST EXIT

31

ENG

ENG

SELECT ADJUST EXIT

TIME

CLOCK : 11 : 35 AM

TIMER : ON

ON TIME : -- : -- AM

OFF TIME : -- : -- AM

SELECT ADJUST EXIT

TIME

CLOCK : 11 : 35 AM

TIMER : ON

ON TIME : 07 : 00 AM

OFF TIME : -- : -- AM

SELECT ADJUST EXIT

TIME

CLOCK : 11 : 35 AM

TIMER : ON

ON TIME : 07 : 00 AM

OFF TIME : 11 : 30 PM

SELECT ADJUST EXIT

Switching the Television On and Off Automatically

TIME

CLOCK : 11 : 35 AM

TIMER : OFF

You can set the On/Off timers so that the television will:

Switch on automatically and tune to the channel of your choice at the time you select

Switch off automatically at the time you select

The first step is to set the television’s clock (refer to

“Setting and Displaying the Current Time” on the previous page). If you have not yet set the clock, the message SET THE CLOCK FIRST is displayed.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the FUNCTION is selected and press the joystick ( ) button.

Result: The FUNCTION menu is displayed.

3 Move the joystick up or down until the TIME is selected and press the joystick ( ) button.

Result: The TIME menu is displayed.

4 Move the joystick up or down to select the TIMER.

5 Set the mode to ON by moving the joystick left or right.

Result: The ON TIME and OFF TIME options are displayed.

6 Move the joystick up or down to select the ON TIME.

7 Set the time at which you wish the television to be switched On.

To...

Move to the hour or minute

Adjust the hour or minute

Move the joystick...

left or right.

up or down.

8 In the same way, set the time at which you wish the television to be switched Off.

9 When you have finished setting the On/Off time, press the TV button, or press the MENU button repeatedly to return to normal viewing.

32

Setting up your Remote Control

This TV’s remote control can operate almost any Cable box, VCR, or DVD, in addition to controlling the TV.

The remote control might not be compatible with the TV manufactured by another company.

1

Turn off your Cable box, VCR, or DVD.

2 Press the SELECT button and make sure that the CABLE or

VCR/DVD LED is illuminated.

The remote control has four modes: TV, PC, CABLE and

VCR/DVD. Press the SELECT button to switch the remote control to the CABLE or VCR/DVD mode.

3

Press the SET button.

4 Enter 3 digits of the Cable box, VCR, or DVD code listed for your brand of Cable box, VCR, or DVD.

Make sure you enter 3 digits of the code, even if the first digit is a “0.” If more than one code listed, try the first one.

5

Press the POWER button on the remote control. Your Cable box, VCR, or DVD should turn on. If they turns on, your remote control is now set correctly.

If your Cable box, VCR, or DVD does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for the brand of particular yours. If no other codes are listed, try each code, 000 through 089 for VCR/DVD and 000 through

077 for Cable box.

6 Once your remote control is set up, press the SELECT button any time you want to use the remote to operate your Cable box, VCR or

DVD.

◆ When your remote control is in the CABLE or VCR/DVD mode, the volume buttons still control your TV’s volume.

◆ When your remote control is in the TV or CABLE mode, the VCR control buttons (PLAY, PAUSE, etc.) still operate your VCR.

GI

SA

TOCOM

PIONEER

ZENITH

Cable Box Codes

000 001 002

003 004 005

006

007 008

009 010

DENON

PANASONIC

PHILIPS

PIONEER

SAMSUNG

SONY

THOMSON

TOSHIBA

DVD Codes

059 000

060 001

061 002

062 003

063 004

064 005

065 006

066 007

Power

AIWA

AKAI

BLAUPUNKT

DAEWOO

FERGUSON

FISHER

FUNAL

HITACHI

JVC

LG

MITSUBISHI

VCR Codes

000 001

002 003 004 005 006

007 008 009

010 011 012 013 014 015 016

017 018

019 020

021

022 023 024 025

026 027

028

029 030

MORDMENDE 031

NEC 032

KONIA

ORION

RADIOLA

SABA

SAMSUNG

SANYO

SHARP

SONY

TELEFUNKEN 057

TOSHIBA 058

033

034 035 036 037

038 039 040 041 042

043 044 045 046

047

048 049 050

051 052

053 054 055 056

33

ENG

ENG

SELECT ADJUST EXIT

PIP

PIP : ON

SOURCE : TV

PROG.NO. : P 1

SIZE : DOUBLE

SELECT ADJUST EXIT

PIP

PIP : ON

SOURCE : TV

PROG.NO. : P 1

SIZE : DOUBLE

SELECT ADJUST EXIT

PIP

PIP : ON

SOURCE : TV

PROG.NO. : P 1

SIZE : DOUBLE

SELECT ADJUST EXIT

PIP

PIP : ON

SOURCE : TV

PROG.NO. : P 1

SIZE : DOUBLE

SELECT ADJUST EXIT

Picture In Picture

(continued...)

PIP : OFF

PIP

You can display a “Picture-In-Picture screen” within the main picture of TV program or Video input. In this way you can watch or monitor TV program or the Video input from any connected equipment while watching TV or other Video input.

For information about connection of other equipment, see pages

42~43.

1

Press the MENU button.

Result: The main menu is displayed.

2 Move the joystick up or down until the PIP is selected and press the joystick ( ) button.

Result: The PIP menu is displayed.

3 Set to ON by moving the joystick left or right.

4 Move the joystick up or down until the SOURCE is selected and move the joystick left or right repeatedly.

Result: The sources of sub picture are displayed in the following order.

TV

AV1 S-VIDEO1 AV2 AV3 S-VIDEO2 AV4

5 Move the joystick up or down to select the PROG.NO..

6 Select the channel that you want to view through sub picture by moving the joystick left or right.

7 Move the joystick up or down until the SIZE is selected and move the joystick left or right repeatedly.

Result: The types of sub picture are displayed in the following order.

DOUBLE

LARGE SMALL

If a different color system (NTSC/PAL) is received when viewing double picture, the sub picture automatically becomes smaller in size and may not be soft.

8 When you have finished, press the TV button, or press the

MENU button repeatedly to return to normal viewing.

34

Picture In Picture

Remote-control functions while “PIP” is “On”:

Features

PIP ON

SWAP

LOCATE

P

/

TV/VIDEO

SCAN

Description

Used to operate ON/OFF function of PIP directly.

Used to interchange the main picture and the sub picture.

When the main picture is in the Video mode and the sub picture is in the TV mode, you might not hear the sound of main picture when pressing the SWAP button after changing the sub picture channel.

At this time, reselect the main picture channel.

Used to move the sub picture counterclockwise.

Used to select the channel of sub picture.

Used to assign a source of sub picture (TV, AV1,

S-VIDEO1 , AV2, AV3, S-VIDEO2, AV4).

Used to scan every memorized channel in order.

To stop scanning, press it again.

Power

ENG

35

ENG

Teletext Feature

(depending on the model)

A B C

E

F

D

Part

A

B

C

D

E

F

Most television channels provide a written information service via

Teletext. Information provided includes:

Television programme times

News bulletins and weather forecasts

Sports results

Travel information

This information is divided into numbered page (see diagram).

Contents

Selected page number.

Current page number or search indications.

Broadcasting channel identity.

Date and time.

Text.

Status information.

FASTEXT information.

Teletext information is often divided between several pages displayed in sequence, which can be accessed by:

◆ Entering the page number

◆ Selecting a title in a list

◆ Selecting a coloured heading (FASTEXT system)

36

Displaying the Teletext Screen

You can display Teletext information at any time on your television.

For Teletext information to be displayed correctly, channel reception must be stable; otherwise:

◆ Information may be missing

◆ Some pages may not be displayed

To activate the Teletext mode and display the contents page, follow the instructions below.

1 Select the channel providing the Teletext service using the P or

P buttons or the VIDEO button ( ).

2 Press the TEXT/MIX button to activate the Teletext mode.

Result: The contents page is displayed.

3 If you wish to display the actual broadcast at the same time as the

Teletext page, press the TEXT/MIX button again.

4 When you have finished, press the TV button to continue viewing normally.

A message box containing the words “No Text

Transmission” will be displayed if the selected channel does not carry a Teletext signal.

ENG

37

ENG

Selecting Display Options

When you have displayed a Teletext page, you can select various options to suit your requirements.

To display...

Both the Teletext information and the normal broadcast

◆ Hidden text

(answers to quiz games, for example)

◆ The screen normally again

A secondary page by entering its number

The broadcast when searching for a page

The next page

The previous page

◆ In letters the upper or lower half of the page

◆ To a full page

Press the...

TEXT/MIX.

(reveal).

.

.

(reveal) again.

(P ).

(P ).

(size) repeatedly.

To return to the normal display after using the reveal or size features, press the TV button again.

38

Selecting a Teletext Page

You can enter the page number directly by pressing the numeric buttons on the remote control.

1 Enter the three-digit page number given in the contents, by pressing the corresponding numeric buttons.

Result: The current page number is incremented until the requested page is reached. That page is then displayed.

If the selected page is linked with several secondary pages, the secondary pages are displayed in turn.

2 If the FASTEXT system is used by the broadcasting company, the different topics covered on a Teletext page are color-coded and can be selected by pressing the coloured buttons on the remote control.

Press the coloured button corresponding to the topic that you wish to select; the available topics are given on the status line.

Result: The page is displayed with other colored information that can be selected in the same way.

3

To display the...

Press the...

Previous/Next page Corresponding colored button.

Subpage 1.

button.

The available subpages are appeared.

2. Select the required subpage.

4 When you have finished, press the TV button again to return to your normal broadcast.

ENG

39

ENG

Setting up your PC

(depending on the model)

How to Set up Your PC Software (Windows only)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card.

First, click on “Settings” on the Windows start menu.

While “Settings” is highlighted, move the cursor so that “Control Panel” is highlighted.

When the control panel screen appears, click on “Display” and a display dialog-box will appear.

Navigate to the “Settings” tab on the display dialog-box.

800 by 600 pixels

Both screen position and size will vary, depending on the type of PC monitor and its resolution.

Resolution Vertical frequency resolution

640 x 480 75/60

800 x 600 75/72/60

The two key variables that apply the TV-PC interface are “resolution” and “colors.” The correct settings for these two variables are:

◆ Size (resolution): 800 x 600 pixels

◆ Color: “24-bit” color (might also be expressed as “16 million colors”) Shown at left is a typical screen for “Display” dialog box.

◆ The interlace mode is not supported.

◆ The TV operates abnormally if a non-standard video format is selected.

If a vertical-frequency option exists on your display settings dialog box, the correct value is

“60” or “60 Hz”. Otherwise, just click “OK” and exit the dialog box.

The text quality of PC screen is optimum in the VGA mode (640 x 480), the full size displayed PC mode is optimum in the SVGA mode (800 x 600).

◆ When this TV is used as a PC display, 24-bit color is supported (over 16 million colors).

◆ Your PC display screen might appear different, depending on the manufacturer (and depending on your particular version of Windows). Check your PC instruction book for information about connecting your PC to a TV display-monitor.

◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHZ (horizontal).

◆ In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the TV button to enter the TV mode. Also, make sure that the PC is connected.

◆ If a phenomenon with an unstable horizontal sync happens while using your PC, please check the power saving mode and power condition of PC and cable connections.

40

Changing the Screen Size or Position of your PC

You can set up the size or position of the screen which best corresponds to your viewing requirements by simply moving the joystick of the remote control.

1

Press the SELECT button to select PC mode.

Result: The PC mode LED illuminates.

2

Press the POSITION/SIZE button.

Repeatedly pressing the POSITION/SIZE button alternates between position control and size control.

3 To expand or compress the image...

Press the...

Horizontally

Vertically

4

To move the image...

Up or down

Left or right or button.

- or + button.

Press the...

or button.

- or + button.

Power

Connecting to the PC Input

(depending on the model)

Front of TV

Personal Computer

Side of TV

and

ENG

◆ The PC INPUT/RCA(AUDIO-L+R) connectors are used for interfacing with your PC.

◆ Only black signal is output from a monitor in PC mode.

41

ENG

Connecting to the AV Input/Outputs

(depending on the model)

◆ The AV connectors on the rear of the television are used for equipment with an AV output, such as video games, video disc players or VCR.

◆ For a Mono VCR, connect to the AUDIO-L.

Rear of TV AV cable

or

VCR

Decoder/

Video game device

Video disc player

Camcorder

Satellite receiver or

Connecting to the AV Input

(depending on the model)

Front of TV

Side of TV

◆ The RCA (VIDEO + AUDIO-L and R) connectors are used for equipment such as VCR, camcorders, video disc players and some video game devices.

◆ For a Mono VCR, connect to the AUDIO-L.

VCR

Decoder/

Video game device

Video disc player

Camcorder

42

Connecting to the DVD Input

Rear of TV

The DVD/RCA (AUDIO-L and R) connectors are used for equipment with a DVD output.

DVD

ENG

Connecting to the S-Video Input

(depending on the model)

Front of TV

◆ The S-VIDEO/RCA (AUDIO-L and R) connectors are used for equipment with an S-VIDEO output, such as a camcorder or VCR.

◆ For a Mono VCR, connect to the AUDIO-L.

Side of TV

Camcorder and

VCR

Rear of TV

To playback pictures and sound both the S-VIDEO and the RCA (AUDIO-L and R) connections must be used.

43

ENG

Connecting to the Audio Output

Rear of TV

The AUDIO OUTPUT RCA connectors are used for equipment, such as an audio system (to take full advantage of the Surround sound effect).

Audio system

See the page 29 for further details on “Setting the Dolby ProLogic”.

Viewing Pictures From External Sources

Once you have connected up your various audio and video systems, you can view the different sources by selecting the appropriate input.

1 Check that all the necessary connections have been made.

2 Switch the television on and if necessary, press the VIDEO button one or more times until the required input is displayed.

Depending on the source selected, the pictures may appear automatically.

To watch television programmes again, press the TV button and select the number of the channel required.

44

Automatic Degaussing to Remove Colour Patches

A degaussing coil is mounted around the picture tube, so you do not normally need to degauss the television manually.

If you move the television to a different position and color patches appear on the screen, you must:

◆ Switch the television off by pressing the “ I “ (ON/OFF) button on the front panel

◆ Unplug the television from the wall socket

◆ Leave the television power-off (stand-by) for about 30 minutes so that the automatic degauss function can be activated, and then press the POWER button on the remote control.

If your television will be left unattended, press the “ I “ (ON/OFF) button to turn your television off.

ENG

Troubleshooting: Before Contacting Service Personnel

Before contacting Samsung after-sales service, perform the following simple checks.

If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer.

No sound or picture

Normal picture but no sound

No picture or black and white picture

Sound and picture interference

Blurred or snowy picture, distorted sound

Remote control malfunctions

◆ Check that the mains lead has been connected to a wall socket.

◆ Check that you have pressed the “ I ” (ON/OFF) button.

◆ Check the picture contrast and brightness settings.

◆ Check the volume.

◆ Check the volume.

◆ Check whether the MUTE button has been pressed on the remote control.

◆ Adjust the colour settings.

◆ Check that the broadcast system selected is correct.

◆ Try to identify the electrical appliance that is affecting the television and move it further away.

◆ Plug your television into a different mains socket.

◆ Check the direction, location and connections of your aerial.

This interference is often due to the use of an indoor aerial.

◆ Replace the remote control batteries.

◆ Clean the upper edge of the remote control (transmission window).

◆ Check the battery terminals.

45

ENG

Memo

46

Memo

ENG

47

- AFTER SALES SERVICE

- Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present.

ELECTRONICS

AA68-02151A-01 (ENG)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents