catalogue advanced 11.4

catalogue advanced 11.4
CATALOGUE
ADVANCED
11.4
THE POWER
OF EXPERIENCE
ESD safe
All JBC products comply with EC regulations,
and the ESD recommendations.
2
www.jbctools.com
More than 80 years of experience have placed JBC at
the technological forefront of tools for soldering and rework
operations in electronics.
Innovation, efficiency and reliability are the key features of a
wide range of products which have been designed to satisfy
the most demanding requirements of professionals.
High technology,
superior quality.
Making the products perfect is one of the main objectives
of JBC’s improvement and development program. The
R&D department has created the most innovative soldering
technologies, which JBC is proud to present in this catalog.
All JBC products comply with EC regulations and ESD
recommendations.
A global
organization at
your service.
JBC’s global organization of local offices and a distributor
network spanning 5 continents puts at your disposal a solid
commercial organization that guarantees quick and efficient
service.
www.jbctools.com
3
ADVANCED Series
The key to succesful handsoldering in
the LEAD FREE era
As soldering has become more demanding due to the use
of lead-free alloys and increased complexity and thermal
characteristics of PCBs, the need for tools with outstanding
specifications is more than evident.
With a unique heating system, controlled by microprocessors,
an exceptional heat recovery is achieved which enables to
work at lower temperatures, while at the same time increasing
the quality and reliability of solder joints by 80%.
By controlling the heat, we improve quality.
JBC’s technology exceeds the performance of the
best tools in the market by 80%. Refer to the graphs
below which show the results of empirical tests.
A/ Time to reach 350º C
350º C
JBC
JBC has revolutionized the soldering process by offering
higher reliability and cleaner soldier joints.
Others
JBC tools solder efficiently at 350 degrees (662 F) – no tool
from any competitor achieves the same!
20
0
2
4
6
8
10
12 sec.
Graph A shows responsiveness of a standard station compared
to a JBC station. A standard station needs between 10 and
90 seconds to reach 350ºC, while any JBC station equipped
with a T210 hand-piece reaches the same temperature in only
2 seconds. The superior responsiveness of the JBC system
could not be clearer.
We invite you to discover the outstanding
performance of JBC tools.
We have demo stations at your disposal,
contact us!
B/ Process for 3 solder joints
JBC
350º C
Dif.30º C
320º C
Other
brands
Dif.70º C
280º C
0
2
4
6
8
10
12 sec.
Graph B shows responsiveness on soldering of 3 joints.
Lack of thermal response of the standard tool results in a
temperature drop of 70º C versus only 30º C of a JBC tool. The
difference grows even bigger for more demanding soldering
applications.
4
www.jbctools.com
A new and revolutionary
technology
JBC’s exclusive heating system generates high power with a
small-size heater.
The result is both a minimum of heated mass and a minimum
of thermal inertia. For optimum performance concerning
immediate temperature recovery, maximum power supply
and minimum temperature fluctuations, the heating system
features an extremely sensitive temperature sensor integrated
in the resistor.
Two solderinig irons in one:
Adaptability to different types
of jobs
Thanks to the cartridge extractor system in the stand and the
temperature recovery system, it was never so easy to change
cartridges without interrupting your work. A single handpiece
enables you to operate with various cartridges.
Ergonomics and usability:
JBC soldering irons are currently the lightest,
smallest and most ergonomic handpieces
available in the market. The short tip-to-handle
distance benefits a higher and more accurate
work performance.
Low Ownership Costs Cartridges
last up to five times longer:
On leaving the soldering iron on the stand,
the temperature of the tip automatically drops
to 180ºC (for soldering stations) and 260ºC
(for desoldering stations); the temperature is
back to work level immediately after taking
the soldering iron from the stand. This ‘standby’ temperature drop significantly reduces
wear of the tip, resulting in extended life up to
5 times longer than that of conventional nonJBC tips.
Easy calibration
Low-temperature soldering for
lead-free soldering
Control of the JBC system by using microprocessors makes
frequent recalibration of the stations unnecessary. If still
required, soldering tips can be easily calibrated by using JBC’s
TI-A thermometer; any other adjustment can be made via the
menu of the station.
Pull slightly to remove the cartridge.
Push gently and place a new one.
JBC systems allow soldering at 380º C
instead of 450º C thanks to its highly efficient
temperature recovery system. This system
eliminates the risk of damaging components
by applying excessive heat and therefore
optimizes the quality of your operations.
www.jbctools.com
5
DS360 Micro desoldering iron
AP130 Solder feed iron
T210
Handpiece
6
T245
Handpiece
PA120 Micro hot tweezers
www.jbctools.com
COMPACT line Stations
Concentrated rework power
JBC offers two lines of soldering stations, each designed
to work with a dedicated tool. A stand incorporated in the
housing of the control unit offers a safe place to put down the
handpiece.
Each station has been designed for work with a designated
tool.
The integrated, intelligent sleep and hibernation features
combine perfectly with the fastest temperature recovery
system available in the market.
Process control
Set temperature limits, check usage counters, lock the station
with a PIN, or program sleep and hibernation modes.
Depending on your requirements you can save up to 3 different
temperature settings; changing from one saved temperature
setting to the next will always increase or decrease the
temperature level to the next of all saved temperatures.
The stations are operational regardless if saved temperature
settings are activated or not.
Intelligent Heat Management
The only time a soldering iron must reach its required
temperature level is during a soldering operation. JBC’s
intelligent heat management detects how the tools are used;
accordingly the integrated support function activates the
sleep or hibernation mode. The intelligent heat management
helps to extend tip life by lowering temperature; it also helps to
save energy by reducing power usage to 10W in sleep mode
and 4W in hibernation mode.
Help us to protect the environment and to save energy!
Quick Tip changer
No tools or pads are needed to change a cartridge. Simply
place the tip in the extractor of the stand, remove one cartridge
and insert another one. Reduce idle time while increasing
operator safety.
www.jbctools.com
7
8
www.jbctools.com
COMPACT line Soldering and desoldering stations
This product range features 4 stations, each designed work
to with one dedicated tool. The corresponding stands are
incorporated in the same housing as the control unit for easy
handling.
Each station works with its designated tool.
Cartridge extractor: An easily accesible location of the extractor
for rapid cartridge change.
Tip wiper: Tapping and wiping: Very soft and temperature resistant
receptacle allows tapping and wiping of the tip to eliminate excess
solder.
Adjustable stand: Fast and simple adjustment of the angle of the
stand without requiring additional tools.
Cable collector: Maintains working area free of cable.
Brass wool housing: Contains metal wool and minimises splashing
of solder particles.
The intelligent sleep and hibernation functions, which help to
extend tip life and to save energy, are combined with extremely
fast temperature recovery unrivalled in the market.
Sponge: For final cleaning.
Optional
Metal brushes for more aggressive cleaning.
Retinner chemical cleaning system.
Cable collector
Adjustable stand
Cartridge extractor
User friendly
program
Metal wool
Tip
cleaners
Tip wiper
www.jbctools.com
9
COMPACT line Soldering and desoldering stations
CD Soldering station · 230V
The CD soldering control units feature large back-lit graphic
displays that show important information at a glance. Any
changes to the original setting can be easily made via menu
on the display. All settings can be locked by PIN.
Basic specifications
Nominal power: 75W
Peak power: 140W
Temperature range: 90-450º C
CD-2BB Soldering station
General electronics jobs.
Included Control unit CD
Handpiece T245-A
Cartridges C245-903 & C245-741
CD-2SB Soldering station
For high precision solder joints.
Included Control unit CD
Handpiece T210-A
Cartridges C210-001 & C210-008
CF-2B Solder feed Station · 230V
Designed for repetitive soldering or when you need a free
hand. Equipped with solder feed iron of 1mm diameter.
Basic specifications
Nominal power: 75W
Peak power: 140W
Temperature range: 90-450º C
IncludedCF control unit
AP130-A Solder feed iron
10
C130-403 cartridge
www.jbctools.com
CP-2B Micro tweezers Station · 230V
For soldering and desoldering SMD components with
Micro-Tweezers.
Basic specifications
Nominal power: 2 x 20W
Peak power: 2 x 40W
Temperature range: 90-450º C
Included Control unit CP
PA120-A micro hot tweezers
2 X C120-002 cartridge.
CS/CV Desoldering Station · 230V
Desoldering stations with electric or pneumatic suction systems.
Basic specifications
Nominal power: 20 W
Peak power: 30 W
Temperature range: 180º-450º C
CS-2B Electric system
Included Control unit CS
DS360-A Micro desoldering iron with tip C360-004
MS-A Electric vacuum pump
CV-2B Pneumatic system
Included Control unit CV
DS360-A Micro desoldering iron with tip C360-004
MV-A Pneumatic suction system fed by compressed air max. 6 bar.
www.jbctools.com
11
MS or MV
Suction module for
desoldering iron
DI, DD, DM
control units
for 1, 2 and 4 tools
JT or TE
High power hot air station
PA120-A
12
www.jbctools.com
MODULAR line Stations
The JBC Modular Line features 4 control units, 6 stands, 8
tools, and more than 300 cartridges and tips adaptable for
the tools.
All components can be freely combined for a completely
personalized set-up.
For example, the 4-tools DM station allows to connect 2
soldering irons, 1 pair of tweezers and 1 desoldering iron.
Combine this set-up with a JT hot air station and you will
have a complete set of tools capable of almost any type of
electronics repair.
Following the above example, combine our 2-tools DD station
with any other station.
JBC’s DI, DD and DM stations offer full connectivity to
any kind of tools like soldering irons, desoldering irons
and tweezers.
Minimum requirements for a functioning soldering station are
a control unit, a stand, 1 tool and 1 cartridge.
Stands
DR560-A
T245-A
www.jbctools.com
T210-A
13
14
www.jbctools.com
DI-2B 1 Tool control unit · 230V
The DI-2B 1 tool digital control unit features a digital read-out
display for accurate temperature and tool control.
This control unit was designed for production and rework
applications for low to medium thermal requirements.
All JBC tools are fully connectable to all control units (use
corresponding stands for tools), including DR560 and DS360
desoldering irons in combination with either of JBC’s electric
suction systems MS-A and MV-A.
The control unit features adjustable sleep and hibernation
modes, as well as adjustable temperature settings. All values
can be locked by PIN.
DI-2B 1 tool control unit
Basic specifications
Nominal power: 75W
Peak power: 140W
Sleep power: 10W
Hibernation power: 4W
Temperature selection: 90-450 ºC
Weight: 2 kg
For a complete soldering station the following is needed;
Control unit
One tool with corresponding stand & cartridge.
www.jbctools.com
15
DD & DM 2 & 4 Tools digital control units · 230V
The DD and DM 2 & 4 Tools digital control units feature a digital
read-out display for accurate temperature and tool control.
The DD-2B 2 tools control unit offers connectivity for working
with 2 tools simultaneously.
The DM-2B 4 tools control unit offers connectivity for working
with 4 tools simultaneously.
These control units were designed for production and rework
applications with high thermal requirements.
The control units feature adjustable sleep and hibernation
modes, as well as independently adjustable temperature
settings for each individual tool. All values can be locked by
PIN.
DD and DM control units are fully connectable to all JBC tools
(use corresponding stands for tools), including DR560-A and
DS360-A desoldering irons in combination with either of JBC’s
electric suction systems MS-A and MV-A.
DD-2B 2 tools control unit
DM-2B 4 tools control unit Basic specifications
Nominal power: 2 X 75W
Total peak power :2 X 140W
Sleep power: 2 X 10W
Hibernation power: 2 X 4W
Temperature selection: 90-450ºC
Weight: 3,5 kg
Basic specifications
Nominal power: 4 X 75W
Total peak power: 4 X 140W
Sleep power: 4 X 10W
Hibernation power: 4 X 4W
Temperature selection: 90-450ºC
Weight: 4,5 kg
For a complete soldering station the following is needed;
Control unit
16
From 1 to 4 tools with its corresponding stand & cartridge
www.jbctools.com
MS-A & MV-A Desoldering suction modules
MS-A and MV-A desoldering suction modules are
indispensable for a complete desoldering process. The control
unit regulates the temperature, while the suction module sucks
in the solder. The suction modules line-up features one electric
model regulated by the control unit, and one pneumatic model
powered by compressed air.
MS-A Electric suction module
MV-A Pneumatic suction module
Electric suction module with overdrive startup function that
offers quick collection of solder before it cools down. This
suction system is regulated by the control unit.
This pneumatic suction module uses compressed air and a
Venturi valve. This system offers outstanding desoldering
results because of its immediate suction responsiveness. This
suction system is powered by compressed unit.
Basic specifications
Power: 12W
Supply: 24V
Weight: 1,7 Kg
www.jbctools.com
Basic specifications
Power: 3W
Supply: 24V
Recommended air pressure: 5 Bar (max. 6)
Weight: 1,4 Kg
17
Tip cleaning stand
JBC introduces different methods for cleaning tips, designed
for removal of oxidation, of residues of flux etc.
With the implementation of lead-free soldering it has become
necessary to use methods to clean tips other than with a
simple wet sponge. The wet sponge can be replaced by dry
cleaning methods like metal wool or metal brushes.
Of all cleaning methods the sponge is the softest, whereas the
brush is the most aggressive. Use of either depends on how
much residue needs to be removed, which in turn is a result of
work temperature and type of solder used.
cl9885 Tip cleaning stand
CL6210 Brass wool
18
cl0236 Tip wiper
www.jbctools.com
optional CLEANING TIPS
cl9885 Tip cleaning stand
CL6205 Inox wool
Tip cleaning stand is designed to be able to be used iright next
to the point of work.
A stronger cleaning method than brass wool.
By his weight and nonskid feet it is totally self-lifting, being able
to use without needing holding the support with the hand or
having to fix it during the cleaning of the tips.
Hood
Contains metal wool and minimises
splashing of solder particles.
CL6210 Brass wool
Very effective cleaning method.
Leaves a small layer of solder on
the tip preventing oxidation between
cleaning and rewetting.
CL6220 Brushes
For more indepth cleaning of the tips, tweezers & desoldering
irons.
CL0236 Tip wiper
Tapping and wiping: Very soft and
temperature resistant receptacle
allows tapping and wiping of the tip
to eliminate the excess of solder.
www.jbctools.com
S0354 Sponge
TT-A Tip tinner
To help the final cleaning.
Chemical system to clean and retin the tip at the same time.
19
Stands
JBC’s stands feature a line-up covering the variety of JBC’s
Advanced Series tools. The stands are placed between
the control unit and the tool for optimum performance, like
temperature reduction in sleep mode when the tool is placed
in the stand for extended tip-life and less oxidation.
All stands can be connected to all Modular line stations.
The cartridge extractor system featured in the stands AD-SB
and DN-SB offers switching cartridges without the need to
interrupt your work.
Cable
collector
AD-SB
For T210-A & T245-A handpiece
Includes
3 cartridges extractor magazine for C210 or C245
Quick cartridges change
Sleep mode
PA-SB
For PA120-A Micro hot tweezers
Includes
Sleep mode
AP-SB
DR-SB
For AP130-A Solder feed iron
For DR560-A desoldering iron
Includes
Includes
Sleep mode
Sleep mode
20
HT-SB
DS-SB
For HT420-A hot tweezers
For DS360-A micro desoldering iron
Includes
Includes
Sleep mode
Sleep mode
www.jbctools.com
Accessories
A1286 Kit extention lead for stand
A1287 Accesory for the desoldering silicon tube
For increased distance between stand and control unit.
Includes a cable of 1.5 m length with corresponding
connectors on each side.
Extension accessory for desoldering iron. Includes a cable of
1.5 m length.
SC-A Cartridges stand
Stand for removal and insertion of up to 12 cartridges of the
C245 cartridges range.
Offers perfect view for quick selection of cartridges.
www.jbctools.com
21
Tools
NANO Tools
The smallest soldering tools available in the market, designed for the smallest SMD components like chips 0201 and smaller. Perfect
for work with magnifier thanks to easy handling and low weight. Cartridges are interchangeable as all others from the Advanced
range, and are capable of giving out 15W of power, in spite of its reduced size.
NP105-A Nano Hot Tweezers
Perfect for soldering and desoldering very small-sized chip
components.
Uses cartridges C105
Real Size.
NT105-A Nano soldering iron
For high-precision soldering jobs
Uses cartridges C105
Real Size.
T210-A Micro handpiece
For high-precision applications
Offers quick cartridge change
Used with C210 cartridges
Fume extractor
F3450 For T210-A handpieces
Real Size.
22
www.jbctools.com
Tools
T245 Handpiece
For general soldering jobs in electronics
Used with C245 cartridges.
Fume extractor
T245-A
Offers quick cartridge change.
F3449 For T245-A handpieces
F6457 For Comfort T470-A handpieces
Real Size.
T245 Nitrogen handpiece
T245-nA
For nitrogen soldering jobs.
Handpiece incorporates a screw that allows to fix the cartridges.
Real Size.
T470 Comfort handpiece
T470-A
T470-SA
Handpiece incorporates a screw that allows to fix the cartridges, Ideal
for high intensity jobs where NO cartridge change is needed.
A screw in this handpiece helps to securely fix the cartridge, ideal
for extensive soldering jobs that do NOT require frequent cartridge
changes. Supplied with a cable of 3 m length.
Real Size.
www.jbctools.com
23
Tools
PA120-A Micro tweezers
The PA120-A micro tweezers are designed for soldering and
desoldering SMD micro components.
Each cartridge is individually controlled by the control unit,
guaranteeing fast heating-up, accuracy and recovery of
temperature.
The available range of cartridges (C120) is made for desoldering
a wide range of components.
The PA120-A micro tweezers connect to JBC stations DI, DD,
DM, AM and Single line AP and CP.
Weight of PA120-A micro tweezers without cartridges 102 g.
Supplied without cartridges.
HT420-A Tweezers
The HT420-A tweezers are designed specifically for soldering
and desoldering small and medium-sized SMD components.
A cable strip cartridge is also available.
Each cartridge is individually controlled by the control unit,
guaranteeing fast heating-up, accuracy and recovery of
temperature.
The HT420-A tweezers connect to JBC station DI, DD, DM,
AM and Single line AP.
Weight of HT420-A tweezers without cartridges 102 g.
Use C420 cartridge range.
24
www.jbctools.com
Tools
DS360-A Micro desoldering iron
The DS360-A micro desoldering iron adapts to the everdecreasing size of new components.
Very easy cleaning and maintenance. Tips are easily inserted
by gentle pushing.
The iron connects to JBC stations DS, DV, CS, CV, DI, DD,
DM, AM and Single line AP.
Weight of DS360-A micro desoldering iron 176 gr.
Supplied with tip C360-004.
Desoldering tip
Desoldering body
with heater
Deposable carton tube
www.jbctools.com
DS360-A Desoldering
Exchangeable filter set
25
Tools
DR560-a Desoldering iron
Very easy cleaning and maintenance.
Two different types of solder residue chambers are available:
metal and glass.
Tips are easily placed by thread.
Weight of DR560-A desoldering iron 254 gr.
Supplied with tip C560-003.
Types of solder chambers
Glass
Metal
Vacuum connector
Desoldaring DR560-A
Desoldering tip
26
Desoldering body
www.jbctools.com
Tools
AP130-A Soldering wire feeding iron
The AP130-A soldering wire feeding iron offers a ‘third hand’ by
feeding soldering wire from diameters 0.8 to 1 mm. Specifically
helpful for high-volume soldering jobs, and whenever an extra
hand is needed.
The iron connects to JBC stations DI, DD, DM, AM and Single
line AP.
Fume extractor
F1204 For AP130-A solder feed iron
Weight of AP130-A solder feed iron 234 gr.
Supplied with cartridge C130-403.
SN5450 Solder reels for AP130-A
The soldering irons are fitted with lead free solder reel 99% Sn / 0,3% Ag / 0,7% Cu - with 50g solder.
www.jbctools.com
27
28
www.jbctools.com
PREMIUM line Stations
Premium line stations are designed for industrial and extensive
use, with extraordinary thermal performance. They are easy to
use and built to last.
The Premium line offers 10 different models, each of them
designed for specific soldering applications.
All stations are ready for immediate use; all stations feature
Plug & Play connectivity.
All components of Premium line stations are stackable for
occupying little work-bench space.
All control units of Premium line stations feature large highcontrast graphic displays that show important information at a
glance. Any changes to the original setting can be easily made
via menu on the display. All settings can be locked by PIN.
All JBC tools are fully compatible to all control stations;
there are no limits to putting together a station that
covers all your personal requirements.
DDST Soldering & desoldering station
www.jbctools.com
29
30
www.jbctools.com
DIT & DIR Soldering stations · 230V
DIT-2B
For general electronic applications
Included Control unit DI-2B
Stand AD-SB
Soldering iron T245-A
Cartridge C245-903
CL9885 Tip Cleaning Stand
Basic specifications
Nominal power: 75W
Total peak power: 140W
Temperature selection: 300-450 ºC
Weight: 2 kg
DIR-2B
For high and medium precision solder-joints
Included Control unit DI-2B
Soldering iron T210-A
Cartridge C210-001
Stand AD-SB
CL9885 Tip Cleaning Stand
AD-SB
Stand
cl9885
Tip cleaning stand
DI-2B
Control unit for 1 tool
T245
Handpiece
T210 Handpiece
www.jbctools.com
31
DIS, DIV & DSS Desoldering Station · 230V
DIS-2B & DIV-2B Desoldering station
DSS-2B Micro desoldering station
For desoldering insertion components and cleaning circuits with SMD
components.
For desoldering small and medium-sized insertion components; highprecision station with small measurements.
Included
Control unit DI-2B
Desoldering iron DR560-A with tip C560-003
Stand DR-SB
MS-A Suction module electric system (DIS-2B)
MV-A Suction module pneumatic system (DIV-2B)
CL9885 Tip Cleaning Stand
Accessories set
Included
Control unit DI-2B
Micro desoldering iron DS360-A with tip C360-004
Stand DS-SB
MS-A Suction module electric system
CL9885 Tip Cleaning Stand
Accessories set
Basic specifications
Nominal power: 75W
Total peak power: 140W
Temperature selection: 300-450 ºC
Weight: 2 kg
DI-2B Control
unit 1 tool
DR-SB
Stand
cl9885
Tip cleaning stand
MS-A electric
suction module
MV-A pneumatic
suction module
DR560-A
Desoldering iron
DS360-A
Micro desoldering iron
32
www.jbctools.com
DIN Nitrogen soldering Station · 230V
DIN-2B Nitrogen soldering
The DIN-2B Nitrogen soldering station combines 2 ways of transferring
heat:
- By direct contact between the solder tip and the solder joint, just like a
normal soldering iron
- By nitrogen which is heated when flowing through the soldering tip.
Included
DI-2B control unit
MN-A Nitrogen flow regulator
Stand DN-SB
CL9885 Tip Cleaning Stand
Nitrogen handpiece T245-NA with C245-903
MN-A Nitrogen flow regulator
*An external nitrogen circuit is needed or the nitrogen
generator from JBC GN-A
GN-A Nitrogen module generator
Basic specifications
Nominal power: 75W
N2 Flow regulation: 0,5 - 3,5 LPM at 5 Bar.
Max. Pressure: 6 Bar.
Compressed air pressure: 4 to 6 Bar
Gas N2 concentration: Up to 99,9 %
Concentrated N2 gas flow: 1 to 2 NL/min.
Weight: 2 Kg.
Peak power: 140W
Temperature range: 90 - 450 ºC
Weight: 1,2 kg
MN-A
Nitrogen flow regulator
DI-2B
Control unit for 1 tool
DN-SB
Stand
cl9885
Tip cleaning stand
T245-NA
Nitrogen soldering iron
www.jbctools.com
33
DDST and DDVT Rework station · 230V
The station DDST and DDVT offers a complete solution for fast
and safe repair of insertion component circuits by suction of
the solder. The station can also be used for cleaning pads in
SMD circuits.
The station features all of JBC’s technological advantages, like
fast thermal recovery, sleep mode, small footprint, low weight,
and easy handling of soldering and desoldering irons.
In addition to the standard functions soldering and desoldering,
this station also offers connectivity of any JBC series tool to
both modules (but only 1 desoldering iron).
MS-A electric
suction module
MV-A pneumatic
suction module
DD-2B
Control unit
DDST-2B & DDVT-2B Soldering & desoldering station
Basic specifications
Nominal power: 2 x 75W
Peak power: 2 x 140W
Sleep mode power: 2 x 10W
Hibernation mode power: 2 x 4W
Temperature selection between: 90-450º C
Weight: 4,5 kg
Included Control unit DD-2B
Handpiece T245-A
Cartridge C245-903 and C245-906
Desoldering DR560-A
Tip C560-003
Stand AD-SB
Stand DR-SB
CL9885 Tip Cleaning Stand
MS-A Suction module electric system (DDST-2B)
MV-A Suction module pneumatic system (DDVT-2B)
Set of tools and accessories
DR560-A
Desoldering
34
T245
Handpieces
www.jbctools.com
DR-SB
Stand
www.jbctools.com
AD-SB
Stand
cl9885 Tip cleaning stand
35
RMST Rework station · 230V
The RM rework station was designed for rework and repair of
through-hole and SMT boards. The station’s 4 modules offer
the following rework/repair operations:
Desoldering of SMD components of any size by hot air. JBC’s
exclusive system of using jointly extractors/protectors and hot
air, which offers safe, fast and clean desoldering, limits heat to
the component to be desoldered, while it protects the rest of
the circuit.
Desoldering SMT and through-hole components, and pad
cleaning. For this operation this station features the desoldering
iron DR560-A and an integrated vacuum pump.
MS-A electric
suction module
Pick & Place tip for placing components.
Soldering of any kind of components with the quick response
and recovery features which are typical of all JBC stations.
The AM rework station features sleep and hibernation modes,
as well as all other features of JBC stations.
DD-2B
Control unit
This station can be easily controlled thanks to accurate
information shown on a large-size display. For maximum
user friendliness and adaptation to individual preferences, all
functions can be saved and locked by PIN.
Modular extension of this station offers almost unlimited
connectivity to the JBC tools range: soldering and desoldering
irons, desoldering tweezers and soldering wire feeding irons.
JTE-2A
Control unit
Características básicas
ominal power: 2 x 75 W
N
Peak power: 2 x 140W
Sleep mode power: 2 x 10W
Hibernation mode power: 2 x 4W
Air pump for hot-air with electronic control
of temperature and air flow.
Vacuum pump for holding ICs.
Maximum Power: 1000 W.
Temperature selection: ºC or ºF,
Temperature room - 450° C and “cool”
Air flow regulation: 6-45 l/min.
The system is protected against
antistatic discharge.
· Weight of complete system: 13 kg.
Heater
36
www.jbctools.com
Repair process of a circuit with SMD components
Desoldering IC
component with hot air
Cleaning pads with
desoldering iron
DR-SB
desoldering
stand
Placing component
AD-SB
handpiece
stand
Soldering from 2
opposite angles
Fluxing IC pads and
leads
Soldering leads with
special JBC series
tips for soldering
SMDs
RMST-2A Rework station
Included Control unit DD-2B
Control
unit JTE-2A
Handpiece T245-A
Cartridge C245-903 and C245-906
Desoldering DR560-A
Tip C560-004, C560-005 and C560-013
Stand AD-SB
Stand JT-SB
Stand DR-SB
CL9885 Tip Cleaning Stand
MS-A Suction module electric system
Heater 1000 W
Extractor stand with 5 extractors, 5 protectors
and two tripods.
cl9885 Tip cleaning stand
DR560-A
Desoldering iron
T245-A Handpieces
www.jbctools.com
37
JT High power hot air station · 230V
JT-2A
The JT-2A station is a high power hot air station used for
desoldering all types of SMDs.
Basic Specifications
Air pump for hot-air with electronic
Its powerful heater desolders even the biggest QFPs and
PLCCs quickly and safely. Desoldering small and mediumsized BGAs is done in a very short time.
Digital readout of temperature and airflow offers maximum
accuracy and control.
JBC’s exclusive system uses jointly extractors/protectors and
hot air for fast desoldering and protecting the surrounding
components by concentrating heat on the component to be
desoldered.
IncludedControl unit JTE-2A
As an example, desoldering an integrated, medium-sized QFP
can be finished in approximately 20 seconds.
Extractor stand
control of temperature and air flow.
Vacuum pump for holding ICs.
Maximum Power: 1000 W.
Temperature selection: ºC or ºF,
Temperature room - 450° C and “cool”
Air flow regulation: 6-45 l/min.
The system is protected against antistatic discharge.
Weight of complete system: 8,7 kg.
Heater 1000 W
Extractor stand with 5 extractors, 5 protectors
and two tripods.
Heater stand and set of accessories.
JTE-2A
Control unit
JT-SA
Heater stand
Heater
38
www.jbctools.com
Desoldering a QFP with the system JT or TE
1. Place the extractor.
2. Heat until is undone soldering joint.
3. DesolderedIC is removed automatically.
20 seconds to desolder a medium QFP.
Ref.
PROTECTORS
A
B
A and B are inner workable areas.
1
Supplied with the station JT -2A
Supplied with the station TE-2A
*Reference desk
2
P3353
P3786
P3352
P3355
P3356
P3785
P3784
P4035
P4040
P4080
1-2
32* P2220
P4045
P4090
1-2
24* P2235
P1249
Amm
4,3
5,2
5,2
5,2
6,2
7,2
8,2
9
9,5
9,5
10
10,5
11
12
12
Bmm
EXTRACTORS
Ref.
B
52* E2052
1-2
64* E2064
1-2
80* E2184
1
68* E2068
E4020
E4015
1
84* E2084
E2100
E2124
Amm
20
20
24
27
28,5
31,5
33
38
45
12,5
31,5
13,2
21,5
15
17
29
18,5
24
28,5
31,5
46
50
14
Bmm
20
26
24
27
28,5
31,5
33
38
45
øC
Ref.
www.jbctools.com
12,5
13
13,2
13,5
15
17
18
18,5
18,5
28,5
31,5
33
50
52,5
Tripods
1-2
A
44* P4000
P1593
P3354
P4025
1-2
48* P2230
1-2
60* P4010
P4005
P4030
P1068
P2685
P4085
P2672
P4002
P3357
1-2
3
5,2
7,5
9,5
4,2
7,2
8,2
13
19
21
10
21
16
17
23
øCmm
1-2
T2050
39
1-2
T2250
85
E2190
Manual extractor
39
TE Hot air station precision station · 230V
The TE-2A is a precision hot air station ideal for soldering and
desoldering small and medium-sized SMD components.
TE-2a
With the TE-2A hot air station it takes approximately 30
seconds to desolder medium-sized components, fast enough
to prevent the substrate and the component from being
exposed to harmful temperatures. In combination with JBC’s
unique system of extractors, the TE-2A hot air station is the
safest hot air desoldering system available in the market.
Basic specifications
Autonomous hot air station, digital, thermo regulated with air flow control.
Power maximum out: 300 W.
Temperature selection: ºC or ºF, Room - 450 °C and cool
Variable air flow settings between 4 and 11 l/min.
Weight of complete system 6,7 Kg.
Included Control unit JTE-2A
Extractor stand
JTE-2A
Control unit
Heater 300 W.
Heater stand JT-SA
Accessories.
Extractor stand with 2 tripods,
3 extractors and 5 protectors.
Heater stand
JT-A
Heater
40
www.jbctools.com
HD Heavy duty station · 230V
The HD-2B heavy duty station is the ideal solution for high
thermal demand and prolonged heavy duty soldering
applications.
This station was specifically designed for extensive soldering
of multi-layered circuits and parts which require high
temperatures.
The temperature of the tip is controlled by a sensor integrated
in the heater, which permits quick temperature recovery.
The HD heavy duty station offers high reliability for extensive
applications as for example the production of solar panels.
The HD heavy duty station features sleep and hibernation
modes, as well as all other features of JBC stations.
HD-2B
Basic specifications
Nominal Power: 145 W.
Total peak power: 270 W.
Sleep mode: 20 W
Hibernation mode: 9 W
Temperature Range: 90 - 500º C.
Weight: 4,5Kg.
Included Control unit HD-2B
Stand HD-SB
CL9885 Tip Cleaning Stand
Handpiece T470-A
The T470-A handpiece can be connected to the station using
the C470 cartridge range.
HD-2B
Control unit
HD-SB
stand
cl9885 Tip cleaning stand
T470-TA
Handpiece
www.jbctools.com
41
AL Automatic Solder feed station · 230V
The AL automatic solder feed station is the ideal solution for
extensive soldering application, and any soldering application that
requires one or two free hands.
This station automates the soldering process by feeding soldering
wire, using all advantages of JBC soldering stations.
With the AL-2A automatic solder feed station it is possible to:
- Select length and speed of wire feeding
- Select work cycle: continuous or step-by-step
- Capture and control of work hours and solder cycles
AL-2A
Control unit
AL-2A Solder feed station
Basic specifications
Nominal power: 75 W.
Peak power: 140 W
Sleep mode: 10 W
Hibernation mode: 4 W
Temperature regulation: 90 - 450 ºC.
Uses soldering wire diameters 0.5 to 1.5 mm, with appropriate wire guide accessories
Capacity of solder reels up to 2 Kg.
Weight: 3,2 kg.
Included Control unit AL-2A
Complete handle AL250-A
Cartridge C250403
Stand AL-SB
CL9885 Tip Cleaning Stand
Tubes set and guides, for: wires
ø 0,9 - 1 mm: 0002401
AL 2500 Station accessories
Tubes set and guides for:
wires ø 0,4 - 0,5 mm P/N.: 0002399
wires ø 0,6 - 0,8 mm P/N.: 0002402
wires ø 0,9 - 1,0 mm P/N.: 0002401
wires ø 1,0 - 1,5 mm P/N.: 0002843
Pedal set with cable and connector
Ref.: 0964551
Fume extractor accessory AL-A
Ref.: 0004468
Arm for soldering iron AL
Ref.: AL-IA
42
AL250-A
www.jbctools.com
BE-SA Solder reel stand
The ideal accessory for easy soldering wire supply.
Specifications
Can be used vertically and horizontally.
For reels in standard DIN sizes.
Capacity: reels of 1 kg and 2,5 Kg maximum.
AL-SB stand
AL-SA stand
AL-IA Hands-free soldering
arm for soldering iron AL
Indispensable for using the AL system while
having both hands free.
For this purpose it is also necessary to use the
pedal set Ref. 0964551
www.jbctools.com
43
NAST Nano station · 230V
The Nano station is a complete station designed for micro
soldering and desoldering of small-size components like chips
0201, 0402 etc.
Tools for this station; Nano soldering iron NT105-A and nano
tweezers NP105-A are the lightest, tiniest and ergonomic of
the market, which allows you to work at highest precison.
The control unit is fully compatible with either tweezers or
irons.
NAST-2A
NP105-A
Nano tweezers
Basic specifications
Nominal Power 15W
Peak power 30W
Temperature regulation: 90-450º C
Weight: 2,6 kg
Included Control unit NA-2A
Nano soldering iron NT105-A
Nano tweezers NP105-A
Cartridge set x 2 (10 pcs)
Set:
C105-101
C105-103
C105-105
C105-108
C105-111
C105 Cartridges for NP105 and NT150
¥
¥
¥
¥
C105-101
C105-103
C105-106
C105-107
_
C105-108
1 x 0,3
C105-113
E 1:1
¥
ø 0,5
C105-105
1,8 x 0,5
¥
C105-114
C105-109
0,7
C105-110
3,5
C105-111
0,3
2,5
C105-112
Galvanic treatment of tips offers outstanding thermal performance and long duration.
44
www.jbctools.com
NT105-A
Nano soldering iron
A1205
Extension cord
www.jbctools.com
45
Cartridges
E 1:1
C105 Cartridges for NP and NT
Galvanic treatment of tips offers outstanding thermal performance and long duration.
¥
¥
¥
¥
C105-101
C105-103
C105-106
C105-107
_
C105-108
1 x 0,3
C105-113
¥
ø 0,5
C105-105
1,8 x 0,5
¥
C105-114
C105-109
C105-110
0,7
3,5
0,3
C105-111
2,5
C105-112
C120 Cartridges for microtweezers PA120 handpiece
Galvanic treatment tips offers outstanding thermal performance and long duration.
CHIPS COMPONENTS
C120-002
C120-902
1,5mm
ø 0,2
C120-006
1,5mm
ø 0,3
C120-004
1,5mm
ø 0,5
ø0,7
1,5mm
DUAL IN LINE
C120-001
C120-003
C120-005
C120-007
C120-008
C120-008
C120-007
ø 0,2
46
3mm
5mm
mm
3,5
C120-009 C120-010
C120-009
C120-010
m
6m
www.jbctools.com
Cartridges
E 1:1
C130 Cartridges for solder feed AP130 iron
Galvanic treatment tips offers outstanding thermal performance and long duration.
ø 0,8
C130-401
C130-402
C130-403
1,8x0,8
1,2x0,7
www.jbctools.com
C130-405
C130-409
ø4
ø3
C130-410
C130-416
C130-417
3,2x1,5
2,2x1
C130-404
ø 2,2
ø 1,7
ø1
ø 0,6
C130-406
C130-418
47
Cartridges
E 1:1
C210 Cartridges for T210 handpiece
Galvanic treatment tips offers outstanding thermal performance and long duration.
ø 0,2
ø 0,3
ø 0,3
ø 0,5
ø 0,6
ø1
C210-009
C210-016
C210-001
C210-013
C210-003
C210-005
ø 0,2
C210-002
ø 0,3
C210-010
ø 0,7
C210-014
C210-004
2,3x0,7
1,3x0,6
ø1
C210-006
C210-008
TO SOLDER INSIDE A CONNECTOR
0,8
ø 0,5
5
C210-007
0,7
C210-018
2,4
ø1
0,4
C210-012
TO SOLDER THROUGH HOLE
COMPONENTS ON MULTILAYER PCBS
ø2
ø 0,7
1,2
VIEW A
2:1
48
2,3
C210-015
4,5
A
C210-017
www.jbctools.com
Cartridges
E 1:1
C245 Cartridges for T245 handpiece
Galvanic treatment tips offers outstanding thermal performance and long duration.
SUPER CARTRIDGES
0,8x0,6
C245-407
C245-406
ø3
ø1
ø 0,6
C245-403
C245-107
ø 0,5
C245-032
1,2x0,7
C245-442
C245-056
C245-256*
C245-036
C245-930
ø1
C245-001
C245-201*
C245-957
6,6x1,8
C245-908
C245-808*
C245-966
C245-866*
ø4
C245-260*
ø 0,8
ø 0,6
4,8x1,5
ø2
C245-951
C245-903
C245-803*
2,7x1
3,2x1,2
ø 1,2
C245-628*
ø 2,2
ø 1,7
C245-943
3x1
2,2x1
C245-731 C245-906 C245-944 C245-907 C245-729 C245-061 C245-911
C245-261* C245-811*
C245-806* C245-844* C245-807*
www.jbctools.com
C245-444
ø 3,8
ø 0,5
1,8x0,8
0,6x0,3
3,2x1,2
ø 3,5
C245-405
ø 0,4
2,7x1
C245-741
ø1,5
ø 0,3
C245-030
2,4x0,6
2,2x1
1,2x0,7
C245-742
C245-937
High Thermal Efficency
ø 1,5
C245-933
ø 2,2
ø3
C245-710
C245-905
*These cartridges are 20mm longer than normal cartridges for easy access to applications difficult to reach.
C245-945 C245-912
C245-845* C245-812*
49
Cartridges
E 1:1
C245 Cartridges for T245 handpiece
ø 0,4
ø 0,4
ø 0,4
C245-034
C245-234*
ø 0,8
ø 0,6
C245-029 C245-126
MINI SPOON
C245-929
1,8x0,8
ø3
ø 1,5
ø1
1,2x0,7
C245-935 C245-904 C245-259* C245-627* C245-962
C245-804*
C245-862*
QFP Y PLCC
4,5x1,8
4,5x1,8
A
C245-938 ØA=3,8
C245-931 ØA=2,7
C245-965 ØA=1,9
C245-067
C245-963 C245-946 C245-732
C245-863* C245-846*
CARTridges to solder smt ic
øA
ø 2,3
3,2x1,5
2,2x1
B
A
C245-227*
C245-315*
C245-228*
C245-224*
C245-223*
FOR PLCC SOCKETS
A=17,5 B=17,5
A=15 B=15,0
A=12,4 B=15,0
A=12,0 B=12,0
A=8,5 B=8,5
QFP
PLCC
C245-009
CHIP COMPONENTS
C245-010
blade type
C245-248*
N. of contact positions= 32
A=11,9 B=14,5
C245-247*
N. of contact positions= 44
A=17,0 B=17,0
A
C245-019
C245-018
C245-017
C245-016
DUAL IN LINE
bevel edge tips
C245-949
C245-913
C245-752
C245-914
A=4,5
A=3,4
A=2,2
A=1,9
A=32
A=21
A=15
A=10
Hoof tip with reduced tinned
surface, ideal for touch-up:
0,5
0,4
6
13
A
C245-939
50
C245-955
A
B
C245-226*
C245-215*
C245-304*
C245-305*
C245-306*
C245-222*
C245-303*
C245-221*
C245-250*
C245-220*
A=15,2 B=29,0
A=9,6 B=18,0
A=9,6 B=15,0
A=9,6 B=12,0
A=9,6 B=10,0
A=7,1 B=13,0
A=6,5 B=6,0
A=5,4 B=10,0
A=5,4 B=8,0
A=5,4 B=6,0
ø 1,3 TINNED
ø 2 TINNED
C245-064
C245-102
*These cartridges are 20mm longer than normal cartridges for easy access to applications difficult to reach.
www.jbctools.com
Cartridges
E 1:1
C245 Cartridges for T245 handpiece
Cartridges with chrome finishED, designed for use plastic rivets:
ø 3,2
4,3x0,1
ø5
ø6
ø7
ø 3,8
ø 4,9
ø 6,5
12
ø 1,8
ø 4,1
4,25x2
8
0,7
3
C245-053
C245-109
C245-052
C245-054
C245-138
C245-143
Cartridges with BIG
CONTACT SURFACE TO
SOLDER WIDE AREAS:
6
C245-312*
Cartridges SPECIAL
PRODUCED FOR FAST
SOLDERING ON MALE
CONTACTS:
4
C245-313*
TeflOn
coated tip
C245-124
SPECIAL CARTRIDGE
FOR THROUGH HOLE
SOLDERING:
1,5
ø 8,8
ø1
ø 1,45
20
ø 2,9
6
C245-123
C245-121
EXTRA IRON COATED
TIP, SPECIAL FOR
ROBOTS:
C245-311*
CHISEL TIP (similar
to 245-908 but longer
and more conical):
C245-301*
REWORK
C245-268*
FOR CABLE SOLDERING
C245-119
C245-117
TIP WITH AN
EXTRA TINNED
SURFACE:
1,5x0,5
4,8x1,5
0,4
10
5x1,7
ø1
C245-118
C245-730
C245-708
TO SOLDER INSIDE A CONNECTOR
0,9
3,25
1,25
3
3
2,2
C245-150
www.jbctools.com
pure nickel tip
for hmp (high 1,4x0,7
melting point)
soldering
6
R1
tinned
length
3,5
C245-122
C245-041
THROUGH HOLE DRAG SOLDERING:
5
R2
TINNED
C245-069
A
3
4
1,4
VIEW A
2:1
C245-116
C245-751
*These cartridges are 20mm longer than normal cartridges for easy access to applications difficult to reach.
C245-753
51
Cartridges
E 1:1
C250 Cartridges for AL250 iron
Galvanic treatment tips offers outstanding thermal performance and long duration.
ø 0,8
ø1
ø 0,6
C250-401 C250-402
1,2x0,7
ø 1,7
C250-403
C250-409
1,2x0,7
C250-410
2,2 x 1
2,2x1
4,8x1,5
1,8x0,8
ø 2,2
3,2x1,5
2,2x1
C250-404
C250-405
ø 2,2
C250-406
C250-412
C250-418
ø 3,8
4,8x1,5
C250-407
52
C250-408
C250-411
C250-413
C250-414
C250-415
www.jbctools.com
Cartridges
E 1:1
C420 Cartridges for HT420 tweezers
Galvanic treatment tips offers outstanding thermal performance and long duration.
CHIPS COMPONENTS
BLADE TYPE
C420-271 Amm=1,5
C420-283 Amm=50
C420-272 Amm=2,6
A
QFP Y PLCC
CABLE STRIPPER
C420-279 Amm=8,0
C420-281 Amm=3,5 max.
C420-280 Amm=11,0
C420-282 Amm=3,5 max.
A
A
øA
C420-281
C420-282
C420 Special Cartridges for HT420 tweezers
DUAL IN LINE
C420-273 Amm=4,0
C420-274 Amm=6,0
14,3
C420-275 Amm=8,0
C420-276 Amm=10,0
C420-277 Amm=15,0
C420-278 Amm=20,0
C420-285 Amm=22,0
A
12
15,6
C420-286
2
C420-287
Supplied individually
www.jbctools.com
53
Cartridges
E 1:1
C470 Cartridges for iron T470 with hd station
Galvanic treatment tips offers outstanding thermal performance and long duration.
2x1
2x0,9
C470-013
5,5x1,5
4x1,3
C470-036
3,5x1,5
5x1,2
4x2,5
C470-014
C470-035
C470-017
7,5x1,7
6x1,7
6x1,5
7,5x1,5
C470-002
C470-015
C470-004
10x2,5
C470-016
C470-006
8,9 x1,7
ø 3,5
15,5x2,5
ø 1,7
ø 7,5
C470-009
C470-007
C470-034
C470-018
C470-019
C470-003
C470-001
ø 3,5
2,4
C470-008
54
32,2
C470-023
www.jbctools.com
Cartridges
E 1:1
C470 Special cartridges for iron T470 with hd station
ø 3,4
10,4
10,4
2,5
R6
R6
2,5
ø 12,2
R8
ø 15
C470-005
C470-010
12
4
C470-011
C470-012
22
TINNED
ø 4,2
C470-020
C470-038
Cartridges with chrome finish, designed
for use plastic rivets:
28x4
ø 1,7
ø9
ø 3,5
43
24
20
C470-021
C470-027
C470-022
C470-026
C470-025
C470-032
14x3
12,7x1,9
R31
5x1,8
1,2
90º
C470-028
www.jbctools.com
7,9x1,8
7x1,8
5
3,65
90°
1
C470-030
90°
90°
4
C470-029
8
C470-033
5
6x1,8
3,2
3,6
C470-037
C470-031
55
Desoldering tips
E 1:1
C360 Tips for Microdesoldering DS360 iron
Galvanic treatment tips offers outstanding thermal performance and long duration.
Aø
Bø
C360-001
C360-002
C360-003
C360-004
C360-007
C360-006
ØA=1
ØB=0,6
Ømax. pin=0,4
ØA=1,2
ØB=0,8
Ømax. pin=0,6
ØA=1,4
ØB=1
Ømax. pin=0,8
ØA=1,6
ØB=1,2
Ømax. pin=1
ØA=1,9
ØB=1,4
Ømax. pin=1,2
ØA=3
ØB=1,5
Ømax. pin=1,3
PAD CLEANING tip for Ds360 iron
The pad cleaning tips feature a distinctive contact surface slit which
offers circulation of suction air for easy pad cleaning.
56
standard pad cleaning tip
for Ds360
C360-011
C360-012
ØA=1
ØB=0,6
ØA=1,2
ØB=0,8
C360-013
C360-014
ØA=1,4
ØB=1
ØA=1,6
ØB=1,2
www.jbctools.com
Desoldering tips
E 1:1
C560 Tips for Desoldering iron DR560
Galvanic treatment tips offers outstanding thermal performance and long duration.
C560-001ht
ØA=1,4 ØB=0,6
Ømax. pin=0,4
C560-001
C560-014
C560-004
ØA=2,7 ØB=1
Ømax. pin=0,8
C560-003
ØA=5 ØB=1,3
Ømax. pin=1,1
C560-009
C560-006
C560-005
ØA=4,2 ØB=1,9
Ømax. pin=1,7
C560-006
C560-015
C560-007
ØA=4,8 ØB=2,4
Ømax. pin=2,2
C560-002
C560-009
C560-005
ØA=3,4 ØB=1,5
Ømax. pin=1,3
ØA=1,8 ØB=0,8
Ømax. pin=0,6
C560-003
C560-004
ØA=3,2 ØB=1,3
Ømax. pin=1,1
Bø
C560-002ht
C560-014
ØA=2,5 ØB=0,8
Ømax. pin=0,6
Aø
C560-007
ØA=5,2 ØB=3
Ømax. pin=2,8
C560-015
PAD CLEANING standard pad cleaning tip for DR560 iron
The pad cleaning tips feature a distinctive contact surface slit which
offers circulation of suction air for easy pad cleaning.
standard pad cleaning tip for DR560
C560-011ht
ØA=1,4 ØB=0,6
C560-011
C560-012ht
ØA=1,8 ØB=0,8
C560-012
C560-013
ØA=2,7 ØB=1
www.jbctools.com
C560-013
57
Accessories
TI-A Thermometer
FL Flux
Accessory for measuring tip temperature.
Flux specifically developed for resoldering of components in
repaired circuits.
Soldering right on the temperature measuring point offers
accurate measuring of the real temperature of the solder joint.
FL-15 Little bottle 15ml with applicator brush.
FL-50 Bottle 500 ml equiped with decanting tube.
For measuring the temperature in sleep mode a connection
cable is included. P/N.: 0780476.
Specifications
Temperature range from 21 to 500 ºC.
Replaceable sensor.
Resolution 10 ºC.
Weight 0,7 Kg.
Size: width 165 mm,
height 75 mm,
depth 105 mm.
FS500 Fume extractor switch
This accessory performs as a switch fumes suction system.
The feed of a fume suction system is connected to the FS500
and this to the network acting as a switch. When the soldering
iron is in the stand the fume suction system stops, returning to
work by lifting the iron to use.
This accesory can be connected to the control units, DI, DD
and DM.
58
www.jbctools.com
www.jbctools.com
59
0010392/11-V4
www.jbctools.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement