Samsung AZ12PHA User's Manual

ESPAÑOL
Series
Series
ITALIANO
PORTUGUÊS
FRANÇAIS
AZ09PH
AZ12PH
ENGLISH
USER'S MANUAL
Window-type Room Air Conditioner
(Cooling and Heating )
E S F P I DB98-22423)
DB98-22420A-1.indd
23
2006-5-31
16:31:39
Register your product at www.samsung.com/global/register
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
Risk of electric shock. • Can cause injury or death. • Disconnect all
remote electric power supplies before servicing, installing or cleaning.
• This must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
WARNING
DURING OPERATION
DISPOSING OF THE UNIT
OTHERS
u
Users of this product are cautioned not to attempt repair of this product at their
own discretion. Instead, they are requested to directly contact a designated
service center or the outlet at which the product was purchased.
u
Never spill any kind of liquid into the unit. Should this happen, unplug or main
switch off the unit and contact an authorized service center.
u
Do not insert anything between the air outlet blades because the inner fan may
be damaged and could cause injury. Keep children away from the unit.
u
Do not place any obstacles in front of the unit.
u
Do not spray liquid of any kind into the indoor unit. Should this happen, switch off
the breaker used for your air conditioner and contact your installation specialist.
u
Make sure that the unit is correctly ventilated at all times:
Do not place clothing or other materials over it.
u
If the wireless remote control will not be used for a long time, remove the
batteries. (If applicable)
u
When using a wireless remote control, the distance should not be more than 7
meters from the air conditioner. (If applicable)
u
The air conditioner must be plugged into its own specific power source, which
must be installed in compliance with national wiring,earthing and safety
regulations.
u
If the power cord is damaged in any way, it must be replaced by the manufacturer
or its service agent or a similarly qualified person in order to avoid a hazard.
u
This device must be installed according to the national electrical rules.
u
The appliance must be installation that the plug should be easily accessible
after installation.
u
If the fuse on PC board is broken please change it with the type of T 3.15A 250V.
u
The breaker of the air conditioner should be all-pole switch; and the distance
between its two contacts should be no less than 3.5mm. Such means for
disconnection must be incorporation in the fixed wiring.
u
Before throwing out the device, it is necessary to pull back the battery cells and
get rid of them safely for recycling reasons.
u
When you need to dispose of the unit, consult your dealer. If pipes are removed
incorrectly, refrigerant may blow out and come into contact with your skin,causing
injury. Releasing refrigerant into the atmosphere also damages the environments.
u
Please recycle or dispose of the packaging material for this product in an
environmentally responsible manner.
u
Never store or ship the air conditioner upside down or sideways to avoid damage
to the compressor.
u
The appliance is not intended for use by young children or infirm persons without
supervision: Young children should be supervised to ensure that they do not play
with the appliance.
u
Max current is measured according to IEC standard for safety and current is
measured according to ISO standard for energy efficiency.
E-
DB98-22420A-1.indd
2
2006-5-31
16:31:26
ENGLISH
Contents
 PREPARING YOUR AIR CONDITIONER
n
Safety Precautions.........................................................................................2
n
4
5
6
7
Air Conditioning Unit-Main Parts, Buttons and Display..................................
Remote Control-Buttons.................................................................................
n Getting Started...............................................................................................
n Inserting the Remote Control Batteries . .......................................................
n
 OPERATING YOUR AIR CONDITIONER
n
Cooling Your Room........................................................................................
8
n
Heating Your Room........................................................................................
9
n Airing Your Room...........................................................................................10
n Adjusting the Air Flow Direction Horizontally.................................................11
n Adjusting thr Air Flow Direction Vertically......................................................11
 PROGRAMMING YOUR AIR CONDITIONER
n
Setting the On Timer......................................................................................12
n
Setting the Off Timer......................................................................................13
Setting the Sleep Timer..................................................................................14
n
 RECOMMENDATIONS FOR USE
n
n
n
n
Operating Recommendation..........................................................................15
Temperature and Humidity Ranges...............................................................16
Cleaning Your Air Conditioner........................................................................17
Solving Common Problems............................................................................18
 METHOD OF INSTALLATION......................................................................
19
CAUTION
“The high inrush current of the starting compressor motor can have adverse effects to
the operation of other equipment under unfavorable mains conditions. This equipment
does not comply with the relevant technical standards for the limitation of voltage
fluctuations and flicker.”
Before connection this equipment to the power supply system, please report to your
suply authority and obtain the consent.
Do not connect other electric appliances to the same supply lines.
AZ18
The maximum permissible system impedance at the power junction box is 0.27 ohms.
Usually, the maximum permissible mains impedance will not be exceeded when the
branch to the power outlet is fed from a junction box with a rated current of 32A.
E-
DB98-22420A-1.indd
3
2006-5-31
16:31:26
Air Conditioning Unit - Main Parts, Buttons and Display
The design and shape are subject to
change according to the model.
Air Outlet
Inner air flow blades
(right/left orientation)
Air inlet (Inside)
Outer air flow blades
(up/down orientation)
The air filter is
located in side
Air inlet (Outside)
Ventilation lever
 The power plug may be not supplied
depending on the model.
Power plug
Fan speed indicators
(LOW,MED,HIGH)
Temperature/ Timer
The type of the power plug
may differ according to the
type of local power supply.
Air flow blade swing indicator
Sleep timer setting button
Temperature adjustment
buttons
Timer setting button
Operating mode indicators
(COOL,FAN,HEAT)
Timer indicator
Deice indicator
Remote Control sensor
Air flow blade
swing button
Operating mode selection
button (COOL,FAN, HEAT)
Fan speed adjustment
button
On/Off button
E-
DB98-22420A-1.indd
4
2006-5-31
16:31:26
ENGLISH
Remote Control - Buttons
Timer setting button
Sleep timer setting
button
Operating mode
selection buttons
Air flow blade swing
button
Temperature adjustment
buttons
Fan speed adjustment
buttons
ON/OFF button
E-
DB98-22420A-1.indd
5
2006-5-31
16:31:27
Getting Started
You have just purchased a window-type room air conditioner and it has been installed by your
installation specialist.
Your Owenr’s Instructions contain valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s functions.
This Owner’s Instructions is just for using your air conditioner correctly.
Thus, the illustrations shown in this manual may not exactly match your air conditioners.
The booklet is organized as follows.
 The following figures are shown on pages 4 and 5:
-
Air conditioning unit (main parts, buttons and display)
-
Remote control (buttons)
They will help you find the buttons and understand the symbols displayed.
 In the manual, you will find a series of step-by-step procedures for each function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH


IMPORTANT
NOTE
Moreover,applicable, wherever the illustrations show the positions of the buttons on both the
remote control and the unit itself.
For the...
The illustrations have a...
Remote control
Gray background.
Example:
Unit itself
White background.
Example:
E-
DB98-22420A-1.indd
6
2006-5-31
16:31:27
ENGLISH
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when:
 You purchase the air conditioner
 The remote control does not work correctly

Use two AAA, LR03 1.5V batteries. Do not use old
batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months,
even if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your thumb in
the direction of the arrow and remove it.
2
Insert the two batteries,taking care to respect the polarities:
 + on the battery with + on the remote control
 - on the battery with - on the remote control
3
Close the cover by sliding it back unitl it clicks into place.
Result: You can control all the functions your air conditioning unit
directly from your seat, using the remote control.
E-
DB98-22420A-1.indd
7
2006-5-31
16:31:28
Cooling Your Room
Remote Control
Control Panel
You must select the Cool mode if you wish to lower the temperature
in your room.You can also set the fan speed.
1
If necessary, press the
Result:
(On/Off) button.
 The operating mode indicator (COOL,FAN or HEAT) on the
unit comes on.
 The air conditioner starts up in the mode selected when the
unit was last used.
 The unit beeps twice.
 The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
 Plugged in
 Stopped
It will start up aotomatically after about three minutes.
2
If the COOL indicator is not lit up on the unit:
 Press the
button on the remote control
or
 Press the MODE button on the unit one or more times until the COOL
indicator lights up
Result:
 The unit beeps each time you press MODE.
 The air conditioner starts up in Cool mode.
 You can change modes at any time.
3
To adjust the temperature, press the
or
button on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the
or
button on the unit one
or more times until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
4
To set the fan speed to...
Then...
High
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Med
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Low
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Result:
5
 Each time you press the temperaure buttons.
- The temperature is adjusted by 1°C and
displayed on the control panel
- The unit beeps
 The air conditioner starts cooling if the room temperature
is higher than the selected temperature.
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
E-
DB98-22420A-1.indd
8
2006-5-31
16:31:29
You must select the Heat mode if you wish to heat your room to a
specific temperature. You can also set the fan speed.
1
If necessary, press the
Result:
Remote Control
Control Panel
ENGLISH
Heating Your Room
(On/Off) button.
 The operating mode indicator (COOL,FAN or HEAT) on the
unit comes on.
 The air conditioner starts up in the mode selected when the
unit was last used.
 The unit beeps twice.
 The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
 Plugged in
 Stopped
It will start up aotomatically after about three minutes.
2
If the HEAT indicator is not lit up on the unit:
 Press the
button on the remote control
or
 Press the MODE button on the unit one or more times until the HEAT
indicator lights up
Result:
 The unit beeps each time you press MODE.
 The air conditioner starts up in Heat mode.
 You can change modes at any time.
3
To adjust the temperature, press the
or
button on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the
or
button on the unit one
or more times until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
4
To set the fan speed to...
Then...
High
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Med
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Low
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Result:
5
 Each time you press the temperaure buttons.
- The temperature is adjusted by 1°C and
displayed on the control panel
- The unit beeps
 The air conditioner starts cooling if the room temperature
is higher than the selected temperature.
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
E-
DB98-22420A-1.indd
9
2006-5-31
16:31:30
Airing Your Room
If the atmosphere in your room is stale, you can air it using the Fan
feature and if necessary, evacuate the stale air outside.
1
If you wish to evacuate stale air outside, push the ventilation lever on the
front of the unit to the right and the open position (
).
Result:
The air inside the room circulates and stale air is evacuated
outside.
Otherwise, push the ventilation lever to the left and the closed
position (
Result:
Remote Control
).
The air simply circulates inside the room.
Control Panel
2
If necessary, press the
Result:
3
(On/Off) button.
 The operating mode indicator (COOL,FAN or HEAT) on the
unit comes on.
 The air conditioner starts up in the mode selected when the
unit was last used.
 The unit beeps twice.
If the FAN indicator is not lit up on the unit:
 Press the
button on the remote control
or
 Press the MODE button on the unit one or more times until the FAN
indicator lights up
Result:
 The unit beeps each time you press MODE.
 The air conditioner starts up in Fan mode.

 You can change modes at any time.
 When the air conditioner is in Fan mode, the temperature is not
displayed; in this case, you do not need to set the temperature.
4
To set the fan speed to...
High
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Med
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Low
 Press the
button on the remote control.
or
 Press the
on the unit until the
indicator lights up
Result:
5
Then...
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
E-10
DB98-22420A-1.indd
10
2006-5-31
16:31:31
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the unit,
thus increasing the efficiency of the air conditioner.
1
Press the
Result:
(or
Remote Control
ENGLISH
Adjusting the Air Flow Direction Horizontally
Control Panel
on the unit) button on the remote control.
The inner blades swing automatically left and right.
The blades may stop swinging momentarily when the Deice function

is activated (see page 15 for further details on this function.)They will
start swinging again automatically as soon as the Deice function
stops.
2
To stop the blades moving left and right, press the
button on the remote control.
(or
on the unit)
 To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply press the
(or
on the unit)
button on the remote control when the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Heating
Downwards
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
 If you orient the air flow blades downwards and the unit operates in Cool mode
for a long period of time, dew may:
 From on the surface of the blades
 Drip from the blades
E-11
DB98-22420A-1.indd
11
2006-5-31
16:31:32
Setting the On Timer
Remote Control
Control Panel
The On Timer enables you to switch on the air conditioner automatically after
a given period time.You can set the period of time from 1 hour to 24 hours.
You can set the period of time from 1 hour to 24 hours.
You can select the On Timer only when the air conditioner is off.
1
Check that the air conditioner has been switched off; if necessary,
press the
(On/Off) button.
2
Set the required mode by pressing the appropriate button:

,
or
on the remote control.
 Mode button on the unit (press it one or more times until the appropriate
operating mode indicator lights up)
3
Set the operating time by pressing:

Timer on the remote control.
or

Timer on the unit one or more times.
Possible time is between 1 hour and 24 hours inclusive.
Result:
 The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
 The air conditioner switches on automatically when the
operating time reaches zero.
 You can change the setting mode, fan speed, and air flow direction after
setting the On timer.
To Cancel the On Timer
To cancel the On Timer, press:

Timer on the remote control or unit one or more times until "
" is
displayed.
or

on the remote control or unit (The air conditioner operates in the mode
selected when the unit was last used.)
E-12
DB98-22420A-1.indd
12
2006-5-31
16:31:33
The Off Timer enables you to switch off the air conditioner automatically after
a given period of time.
You can set the period of time from 1 hour to 24 hours.
You can select the Off Timer only when the air conditioner is on.
1
ENGLISH
Setting the Off Timer
Remote Control
Control Panel
Check that the air conditioner has been switched on; if necessary,
press the
2
(On/Off) button.
Set the operating time by pressing:

Timer on the remote control.
or

Timer on the unit one or more times.
Possible times are between 1 hour and 24 hours inclusive.
Result:
 The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
 The air conditioner switches off automatically when the
operating time reaches zero.
 You can change the fan speed and air flow direction and others
after setting the Off Timer.
To Cancel the Off Timer
To cancel the Off Timer, press:

Timer on the remote control or unit one or more times until "
" is
displayed.
or

on the remote control or unit (The air conditioner operates in the mode
selected when the unit was last used.)
E-13
DB98-22420A-1.indd
13
2006-5-31
16:31:34
Setting the Sleep Timer
Remote Control
Control Panel
The Sleep Timer can be used when you are cooling or heating your room to
switch the air conditioner off automatically after a period of 8 hours.
If you wish to switch the unit off at a specific time, refer to page 13.

1
Make sure that you have selected either COOL or HEAT mode.
2
Press the
or
Press the
Result:
Cooling
button on the remote control
button on the unit until the SLEEP indicator lights up.
 Each time you press a butoon, the unit beeps.
 The "SLEEP" passes through the control panel for about 15
seconds and the"
"will be dispalyed.
 The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
 The air conditioner will be controlled as illustration below.
When the temperature has
been increased by 1°C(after
1 hour), it is maintained
for 7 hours.
Heating
Set
TEMP.
Start
time
1hr
8hr
Stop
time
The temperature is decreased
by 1°C after 1 hour.
When it has been decreased
by 2°C (after 2 hour),the
temperature is maintained for
6 hours.
To Cancel the Sleep Timer
To cancel the timer, press:

on the remote control.
or

on the unit.
Result:
 The unit beeps.
 The SLEEP indicator is no longer displyed.
 The air conditioner operates in the mode selected last.
E-14
DB98-22420A-1.indd
14
2006-5-31
16:31:35
ENGLISH
Operating Recommendations
Here air a few recommendations that you should follow when using your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner absorbs heat from outside
air and brings it indoors. If the temperature of the outside air drops,the
air conditioner will heat less. If you find that the room is not warm
enough,use an additional heating appliance.
Warm air circulation
The air conditioner circulates warm air to heat your room;as a result,
some time will be required after starting the air conditioner to warm
the entire room. If necessarty,set the air conditioner going a short time
before you wish to use the room.
Frost
When outside temperatures are low and humidity is high, frost may form
in the unit's condensor when heating with your air conditioner. If this
happens:
 The unit stops heating
 The air flow blades stop swinging
 The Deice mode is triggered automatically for about five minutes
 The DEICE indicator on the unit lights up red
No intervention is required from you;after about five minutes,the air
conditioner starts operating again normally.
High indoor and outdoor
temperatures
If both the indoor and outdoor temperature are high and you select the
Heat mode ,the fan and compressor in the unit may stop at times.
This is normal;simply wait until the air conditioner switches on again.
E-15
DB98-22420A-1.indd
15
2006-5-31
16:31:35
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges within which the air
conditioner can be used .
Mode
IndoorTemperature
OutdoorTemperature
Indoor Humidity
Cooling
21°C to 32°C approx.
21°C to 43°C approx.
80% or less
Heating
28°C or less
0°C to 21°C approx.
-
If the air conditioner is used at...
Then...
Higher temperatures
The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperatures
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels
Water way condense on and drip from the surface of the unit if
it is used for long periods.
E-16
DB98-22420A-1.indd
16
2006-5-31
16:31:35
ENGLISH
Cleaning Your Air Conditioner
Be sure to clean the air filter periodically to maintain the air conditioner in
the best condition for a long period of time.
IMPORTANT When cleaning the air conditioner, turn it off and pull out
the power plug.
1
Hold the front grille handle, slightly pull it to the left side and open the front grille.
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.

CAUTION
Removal and Reassembly of the Front Grille
For user’s safety, a safety clip has been installed in the front grille.

1
Grasp the lower part of the front
grille and the front grille handle,
then open the grille. (The open
angle of front grille has not to be
exceeded 25 degree)
2
Lift the front grille slightly and
remove it from the front panel.
3
Reassembling of front grille
should be done in reverse
order of disassembly.
2
Pull the air filter to the right side.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
If you...
Then...
Will not be using the
air conditioner for a
long period of time
 Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
 Switch the air conditioner off and
unplug it from the wall socket.
 Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
The air conditioner has two or three grille
grooves depending on the model.
E-17
DB98-22420A-1.indd
17
2006-5-31
16:31:36
Solving Common Problems
Before contacting the after-sales service,perform the following simple checks.
They may save you the time and expense of an unnecessary service call.
Problem
Explanation/Solution
The air conditioner does not
 Check that the circuit breaker used for the air conditioner has not
operate at all triggered.
been triggered.
 Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
 Check that the operating mode indicator (COOL, FAN or HEAT) on the
unit is lit up; if necessary press
(On/Off) on the remote control or
unit.
The air conditioner does not
operate with the remote control
 Check that there are no obstacles between you and the unit.
 Replace the remote control batteries if necessary.
 Check that you are close enough to the unit (seven metres / yards
or less).
No beep is heard when you press
(On/Off) on the remote control
 Check that you are pointing the remote control at the remote
control sensor on the unit.
 Replace the remote control batteries if necessary.
The air conditioner does not cool or  Check that the correct operating mode has been selected COOL or
heat.
HEAT.
 The room temperature may be too low or too high.
 Dust may be blocking the air filter; refer to page 17 for
cleaning instructions.
 Check that there is no obstacle blocking the air flow into or out of
the unit.
When heating, the required room
temperature is never reached and
the air conditioner frequently stops
 Check that the required temperature has been set correctly.
 Increase the fan speed.
 If the air flow is directed downwards,direct it upwards.
 Check that the air conditioner has been switched on;if necessary,press
The air flow direction does not
change when you press AIR SWING
(On/Off) on the remote control or unit.
The timer is not correctly triggered
 Check that the timer has been programmed correctly;
see page 12~14.
Odours are permeated in the
 Air the room.
room during air conditioning
E-18
DB98-22420A-1.indd
18
2006-5-31
16:31:37
Installation
ENGLISH
Before installation, be sure to check the installation area or the air
conditioner, and drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
 The appliance must be fixed well by screw or similar
method.
75mm
min.
500mm
500mm
300mm
"170mm"
500mm
Fence, wall
or other
obstacle
Approx.3
750mm

150mm min.
 If the wall is greater than 150mm thick, cut the wall back on a 45 angle if possible.
Outdoor side 45
45
Indoor side
100mm or more
E-19
DB98-22420A-1.indd
19
2006-5-31
16:31:37
In some region, drain tube and drain pan may not be supplied.
Plesae contact the sales agent.
Installation of the Drain Tube
Fix the drain tube as shown in the figure.
Rear
Rubber cap
Gasket
Drain Tube
Screws(2EA)
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
 In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1 Open the front grille; refer to page 17.
2 Remove the screw located at the lower section of the front grille.
It is secured in the
Front panel
section depending on the model.
3 Remove the front panel.
3-1 Press both sides of the cabinet in the directionof the arrow
as shown in the figure.
3-2 Pull the lower part of the front panel slightly forward.
(below three inches)
3-3 Lift the front panel upward.
Screw

Applying excessive force to remove the front panel
may cause damage to the tab; be sure not to use
excessive force.
4 Remove two screws on the lower, right and left sides of the unit.
5 Remove the chassis from the cabinet.
6 Remove the rubber cap inserted into the basepan.
Drain Pan
Rear
7 Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
8 Install the cabinet at the specified area after installing the drain pan,
and then re-assemble it in the original condition.

Rubber cap
Screw
Drain Hose
Bottom-Side View with
Drain Pan and Hose in Place
Secure the front panel to the case by replacing the screw removed in
step 2. If a screw not removed in setp 2, secure the panel with a
supplied screw.
 In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1 Follow steps 6 and 7 only
E-20
DB98-22420A-1.indd
20
2006-5-31
16:31:38
ENGLISH
Memo
E-21
DB98-22420A-1.indd
21
2006-5-31
16:31:38
Country
Customer Care Center ☎
Web Site
MEXICO
ARGENTINE
01-800-SAMSUNG (7267864)
0800-333-3733
0800-124-421
4004-0000
800-726-7864(SAMSUNG)
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
www.samsung.com/mx
www.samsung.com/ar
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
1-800-7267-864
www.samsung.com/latin
0-800-100-5303
01-8000112112
1300 362 603
3030 8282
1800 110011
0800-112-8888
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
1800-29-3232
02-689-3232
1 800 588 889
0860 726 7864 (SAMSUNG)
800SAMSUNG (7267864)
8000-4726
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/au
BRAZIL
CHILE
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD &
TOBAGO
VENEZUELA
COLOMBIA
AUSTRALIA
INDIA
INDONESIA
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
VIETNAM
SOUTH AFRICA
U.A.E
DB98-26004A.indd
22
www.samsung.com/br
http://www.samsung.com/in/
www.samsung.com/id
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/vn
www.samsung.com/za
www.samsung.com/mea
2006-12-5
16:37:44